AE101-SB.pdf

GENERAL NOTES

1. THE ARCHITECTURAL DRAWINGS SHOW PRINCIPAL AREAS AND LIMITS OF

CONSTRUCTION WHERE WORK MUST BE ACCOMPLISHED UNDER THIS CONTRACT.

WORK WILL BE NECESSARY IN AREAS NOT SHOWN ON ARCHITECTURAL DRAWINGS

DUE TO CHANGES AFFECTING STRUCTURAL, ELECTRICAL, MECHANICAL, PLUMBING

AND OTHER SYSTEMS. THIS WORK SHALL BE PART OF THIS CONTRACT. INSPECT

THESE AREAS TO ASCERTAIN WORK REQUIRED AND PERFORM THE WORK IN

ACCORDANCE OF CONTRACT REQUIREMENTS.

2. PROVIDE FIREPROOFING TO THE RATING REQUIRED AS INDICATED IN THE LIFE

SAFETY PLAN, CODE SUMMARY AND PER NFPA ON STRUCTURAL STEEL ELEMENTS.

3. DO NOT SCALE DRAWINGS. NOTIFY ARCHITECT IMMEDIATELY OF ANY

DISCREPANCIES.

4. PATCH OPENINGS CUT THOUGH RATED CONSTRUCTION WITH MATERIALS

COMPATIBLE WITH EXISTING ASSEMBLY TO RESTORE INTEGRITY OF THE RATING.

RESTORE FINISHES OF DISTURBED AREAS TO LIKE NEW CONDITION.

5. GENERAL CONTRACTOR TO CHECK MECHANICAL DRAWINGS FOR EXISTING PIPES

AND DUCTS FURRED IN WALLS. VERIFY SIZE AND LOCATION WITH MECHANICAL

CONTRACTOR PRIOR TO PROCEEDING WITH REMODELING.

6. RESTORE EXISTING FIREPROOFING TO RATINGS INDICATED ON LIFE SAFETY PLANS

WITH MATERIALS TO MATCH EXISTING.

7. AT LOCATIONS WHERE EXISTING FIRESTOPPING IS REQUIRED TO BE ALTERED,

REMOVE EXISTING FIRESTOPPING SYSTEM IN ITS ENTIRETY AND REPLACE FIRE

STOPPING SYSTEM WITH NEW FIRESTOPPING MATERIALS THAT MEET THE RATING

REQUIREMENTS OF THE PENETRATION.

8. DIMENSIONS OF EQUIPMENT ARE THOSE OF THE BASIS-OF-DESIGN EQUIPMENT.

VERIFY DIMENSIONS OF ACTUAL EQUIPMENT BEING PROVIDED TO COORDINATE

SPACE REQUIREMENTS.

9. VERIFY DIMENSIONS OF MECHANICAL OR ELECTRICAL EQUIPMENT PRIOR TO

FABRICATING SUPPORTS FOR THE EQUIPMENT.

10. PATCH AREAS DISTURBED OR MODIFIED BY THIS WORK WITH MATERIALS TO

MATCH EXISTING ADJACENT SURFACES OR SCHEDULED FINISHES AND TO A LIKE

NEW CONDITION.

11. PROVIDE ACCESS PANELS WHERE INDICATED ON DRAWINGS AND WHERE

DESCRIBED IN SPECIFICATIONS SECTION 08 31 13. COORDINATE LOCATIONS AND

SIZES REQUIRED (24" X 24" MINIMUM) WITH MECHANICAL, PLUMBING, ELECTRICAL

AND TECHNOLOGY SUBCONTRACTORS.

12. ABBREVIATIONS AND SYMBOLS OF ARCHITECTURAL, STRUCTURAL, MECHANICAL,

AND ELECTRICAL MAY VARY BY DISCIPLINE. SEE RESPECTIVE DISCIPLINE SECTIONS

AND/OR DRAWINGS FOR DEFINITIONS.

13. AT MECHANICAL AND ELECTRICAL EQUIPMENT ROOMS, PROVIDE 3/4" FIRE

RETARDANT TREATED (FRT) PLYWOOD SURFACE OF SCHEDULED PARTITION FOR

SURFACE MOUNTED FIXTURES AND EQUIPMENT, UNLESS NOTED OTHERWISE. DO

NOT PAINT OVER FRT LABEL.

14. EVALUATE INTEGRITY OF EXISTING LIFE SAFETY RATED PARTITION ASSEMBLIES

INDICATED BY SYMBOLS ON THE LIFE SAFETY PLAN(S) WITHIN THE PROJECT SCOPE

INCLUDING PENETRATIONS THOUGH ASSEMBLY AND BASE AND HEAD OF ASSEMBLY.

WHERE GAPS OR DEFICIENCIES ARE FOUND, RESTORE INTEGRITY OF EXISTING

ASSEMBLIES WITH MATERIAL NECESSARY TO MEET REQUIRED RATING OF THE

ASSEMBLIES.

15. DEFINITIONS OF COMMON TERMS.

• FURNISH: TO SUPPLY AND DELIVER TO THE SITE, READY FOR INSTALLATION

• INSTALL: TO PLACE INTO POSITION SERVICE OR USE

• PROVIDE: TO FURNISH AND INSTALL

FLOOR PLAN SYMBOLS

EXISTING WALL TO

REMAIN

WALL

EXISTING DOOR

AND FRAME TO

REMAIN

DOOR

INTERIOR

BORROWED LIGHT

101B

101A

8'-0"

DIMENSION LINE,

NOMINAL

8'-0" EXTENDED

DIMENSION LINE,

NOMINAL

AE2111A

INTERIOR

ELEVATION

INDICATOR TAG

2B

AE2O1

EXTERIOR

ELEVATION

INDICATOR TAG

1A

203 EQUIPMENT TAG

100 FLOOR SPOT

ELEVATIONWALL TAG

OFFICE

ROOM NAME AND

NUMBER

AE501

1A

DETAIL REFERENCE

TAG

AE2O1

EXTERIOR SECTION

REFERENCE TAG

1A

AE2O1

INTERIOR SECTION

REFERENCE TAG

1A

KEY NOTE

A

GRIDLINE

REVISION TAG

PR01

REVISION CLOUD

NOTE: NOT ALL SYMBOLS MAY BE USED ON EACH PLAN

FP10

B3

CURTIAN WALL TAG

OR

WINDOW TAG

CW1 W3OR

M A

C H

IN

E

S

E E

S H

E E

T

A E

-S

A

BUILDING 10

VAULT #1

LINK B

VAULT #2

EXISTING STEAM TUNNEL

SYSTEM. SEE STRUCTURAL AND

CIVIL

AE101-SA

STEAM PIPING. SEE MECHANICAL

STEAM PIPING SUPPORT SYSTEM.

SEE STRUCTURAL

STEAM TUNNEL. SEE

STRUCTURAL

EXISTING STEAM TUNNEL

SYSTEM. SEE STRUCTURAL AND

CIVIL

STEAM PIPING

EXPANSION LOOP.

SEE MECHANICAL

FE

FE

FE

FE

AE101-SB

AE314

AE314

AE313TYP

ELI-2

ELI-3

ELI-4

UTILITY CROSSING INSIDE

TUNNEL. SEE CIVIL &

STRUCTURAL

VAULT LID PLAN

VAULT LID PLAN

LINE OF HATCH ABOVE. SEE

STRUCTURAL

LINE OF HATCH ABOVE. SEE

STRUCTURAL

3'-0" x 6'-0" RO STEEL FLOOR

HATCH. SEE SPEC 08 31 00

OUTLINE OF HATCH OPENING

CONCRETE BEAM BELOW - SEE

STRUCTURAL

CONCRETE WALL BELOW - SEE

SSTRUCTURAL

VENT PIPE. SEE MECHANICAL

TOP OF VAULT. SEE CIVIL

& STRUCTURAL

TUNNEL ROOF BELOW.

SEE CIVIL & STRUCTURAL

7' -3

3'-10 1/4"

AE314

2'-11"

3' -7

/4

GATE. SEE CIVIL

RAILING. SEE CIVIL

HATCH CURB

VAULT CURB - SEE CIVIL &

STRUCTURAL

OUTLINE OF VENT OPENING.

SEE MECHANICAL FOR PIPE

AND SLEEVE DIMENSIONS

3'-0" x 3'-0" RO STEEL FLOOR

HATCH. SEE SPEC 08 31 00

AE314

SIM

1'-6"

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

100% FINAL BID

DOCUMENTS

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

DESIGNER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

623 26TH AVENUE

ROCK ISLAND, IL 61201

9555 JAMES AVE S. SUITE 200

BLOOMINGTON, MN 55431

C U s e rs

\g b a rb a ri

\D o c u m e n ts

\1

-A -R

G io v a n n i- B a rb a ri .r v t

/7

/2

:0

:2

A M

AE101-SB

SOUTH TUNNEL PLAN - LINK B CONSTRUCT STEAM

TUNNEL

DES MOINES, IA

636A6-23-101

SITE

08/09/2024 JU/LK GJB

17270

0 8' 16'4'

VAULT #2

FUTURE BUILDING

BUILDING 10

LINK B

LINK A

VAULT #1

BUILDING 9

BUILDING 11

SOUTH TUNNEL KEY PLAN

1/8" = 1'-0"

SOUTH TUNNEL - LINK B FLOOR PLAN

1/4" = 1'-0"

ENLARGED PLAN - VAULT 2 LID PLAN

SEE CIVIL AND STRUCTURAL DRAWINGS

FOR ADDITIONAL INFOMATION

0 4' 8'2'

Revisions: Date:

REVISION 1 02/07/2025