GI 01-10 - WALL TYPE DETAILS.pdf

1HR FIRE/SMOKE BARRIER

UL DESIGN #:

STC RATING:

FIRE RATING:

SCALE:

16" O.C.

SECTION

PLAN

3-5/8" STUDB

U465

45 - 49

1HR

N.T.S.

DESCRIPTION:

2 43

ABOVE CEILING ID (STENCIL):

"1HR FIRE/SMOKE BARRIER"

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL

DESIGN # MUST BE MET.

WALL PRIORITY:

1/ 4"

M

IN

OPENINGS: 45 MIN

1. STEEL FLOOR AND CEILING CHANNELS - TOP AND BOTTOM CHANNELS OF WALL

ASSEMBLY SHALL BE MIN. 20 GA. GALV. STEEL SIZED TO FIT STUDS. TOP CHANNEL TO

HAVE 2" FLANGES (MIN). BOTTOM CHANNEL TO HAVE 1-1/4" FLANGES (MIN). SECURE

BOTTOM CHANNELS WITH STEEL FASTENERS AT 24" O.C. (MAX). SECURE TOP

CHANNELS TO VALLEYS OF STEEL FLOOR UNITS (OR STRUCTURE ABOVE) WITH STEEL

FASTENERS AT 12" O.C. (MAX).

2. STEEL STUDS - MIN. 3-5/8" WIDE, 1-1/4" LEGS, 3/8" FOLDED BACK RETURN. FORMED OF

20 GA.(MIN) GALV. STEEL. MAX. SPACING 16" O.C. CUT STUDS 1" LESS IN LENGTH THAN

ASSEMBLY HEIGHT WITH BOTTOM NESTING IN AND SECURED TO FLOOR CHANNEL, AND

WITH TOP NESTING IN CEILING CHANNEL WITHOUT ATTACHMENT.

3. SOUND ATTENUATION BATT INSUL. - 3-1/2" (DEPENDING ON STUD SIZE) GLASS FIBER

BATTS IN STUD CAVITY. FILL ENTIRE CAVITY FULL HEIGHT.

4. GYPSUM WALLBOARD- 5/8" THICK TYPE "X", 4' WIDE, ATTACHED TO STEEL STUDS AND

FLOOR CHANNELS WITH 1" LONG TYPE S SELF-TAPPING STEEL SCREWS AT 8" O.C.

ALONG THE VERTICAL AND BOTTOM EDGES AND 12" O.C. IN THE FIELD OF THE BOARD.

INSTALL WALLBOARD WITH A MIN. 1/2" AND MAX. 3/4" GAP BETWEEN THE TOP OF THE

WALLBOARD AND THE BOTTOM OF THE FLOOR UNIT VALLEYS (OR STRUCTURE ABOVE).

NO SCREWS ARE TO BE INSTALLED WITHIN 4" OF THE STEEL FLOOR UNIT VALLEYS AT

THE TOP OF THE WALL. ORIENT JOINTS VERTICALLY AND STAGGER JOINTS ON

OPPOSITE SIDES OF THE ASSEMBLY. WHEN ATTACHED TO FURRING CHANNELS,

WALLBOARD IS ATTACHED WITH 1" LONG TYPE S SCREWS AT 12" O.C.

5. JOINT TAPE AND COMPOUND - VINYL, DRY OR PRE-MIXED JOINT COMPOUND, APPLIED

IN TWO COATS TO JOINTS AND SCREW HEADS; PAPER TAPE 2" WIDE EMBEDDED IN

FIRST LAYER OF COMPOUND OVER ALL JOINTS. JOINTS REINFORCED.

6. FURRING CHANNELS (OPTIONAL NOT SHOWN) - RESILIENT 20 MSG GALV. STEEL

FURRING CHANNELS SPACED VERT. MAX. 24" O.C. ATTACH FLANGE TO EACH

INTERSECTING STUD WITH 1/2" LONG TYPE S-12 PANHEAD SCREWS.

7. ACOUSTICAL SEALANT.

8. PACKING MATERIAL - MIN. 4" TKNS. OF MIN. 4.0 PCF MINERAL WOOL BATT INSULATION

FIRMLY PACKED INTO FLUTES OF STEEL FLOOR UNITS AS A PERMANENT FORM.

PACKING MATERIAL TO BE RECESSED FROM BOTH SURFACES OF THE WALL AS

REQUIRED TO RECEIVE JOINT SEALANT.

9. JOINT TREATMENT MATERIAL - NON-SAG FIRE CAULK EACH SIDE MIN THICKNESS 1/2",

APPLIED WITHIN THE OPENING BETWEEN THE TOP OF THE WALLBOARD AND ALL

SURFACES OF THE STEEL FLOOR OR STRUCTURE, FLUSH WITH BOTH SURFACES OF

THE WALL ASSEMBLY.

7/

8" M

IN

1HR FIRE BARRIER

UL DESIGN #:

STC RATING:

FIRE RATING:

SCALE:

16" O.C.

SECTION

PLAN

3-5/8" STUDC

U465

45 - 49

1HR

N.T.S.

DESCRIPTION:

2 43

ABOVE CEILING ID (STENCIL):

"1HR FIRE BARRIER"

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL

DESIGN # MUST BE MET.

WALL PRIORITY:

1/ 4"

M

IN

OPENINGS: 45 MIN

1. STEEL FLOOR AND CEILING CHANNELS - TOP AND BOTTOM CHANNELS OF WALL

ASSEMBLY SHALL BE MIN. 20 GA. GALV. STEEL SIZED TO FIT STUDS. TOP CHANNEL TO

HAVE 2" FLANGES (MIN). BOTTOM CHANNEL TO HAVE 1-1/4" FLANGES (MIN). SECURE

BOTTOM CHANNELS WITH STEEL FASTENERS AT 24" O.C. (MAX). SECURE TOP

CHANNELS TO VALLEYS OF STEEL FLOOR UNITS (OR STRUCTURE ABOVE) WITH STEEL

FASTENERS AT 12" O.C. (MAX).

2. STEEL STUDS - MIN. 3-5/8" WIDE, 1-1/4" LEGS, 3/8" FOLDED BACK RETURN. FORMED OF

20 GA.(MIN) GALV. STEEL. MAX. SPACING 16" O.C. CUT STUDS 1" LESS IN LENGTH THAN

ASSEMBLY HEIGHT WITH BOTTOM NESTING IN AND SECURED TO FLOOR CHANNEL, AND

WITH TOP NESTING IN CEILING CHANNEL WITHOUT ATTACHMENT.

3. SOUND ATTENUATION BATT INSUL. - 3-1/2" (DEPENDING ON STUD SIZE) GLASS FIBER

BATTS IN STUD CAVITY. FILL ENTIRE CAVITY FULL HEIGHT.

4. GYPSUM WALLBOARD- 5/8" THICK TYPE "X", 4' WIDE, ATTACHED TO STEEL STUDS AND

FLOOR CHANNELS WITH 1" LONG TYPE S SELF-TAPPING STEEL SCREWS AT 8" O.C.

ALONG THE VERTICAL AND BOTTOM EDGES AND 12" O.C. IN THE FIELD OF THE BOARD.

INSTALL WALLBOARD WITH A MIN. 1/2" AND MAX. 3/4" GAP BETWEEN THE TOP OF THE

WALLBOARD AND THE BOTTOM OF THE FLOOR UNIT VALLEYS (OR STRUCTURE ABOVE).

NO SCREWS ARE TO BE INSTALLED WITHIN 4" OF THE STEEL FLOOR UNIT VALLEYS AT

THE TOP OF THE WALL. ORIENT JOINTS VERTICALLY AND STAGGER JOINTS ON

OPPOSITE SIDES OF THE ASSEMBLY. WHEN ATTACHED TO FURRING CHANNELS,

WALLBOARD IS ATTACHED WITH 1" LONG TYPE S SCREWS AT 12" O.C.

5. JOINT TAPE AND COMPOUND - VINYL, DRY OR PRE-MIXED JOINT COMPOUND, APPLIED

IN TWO COATS TO JOINTS AND SCREW HEADS; PAPER TAPE 2" WIDE EMBEDDED IN

FIRST LAYER OF COMPOUND OVER ALL JOINTS. JOINTS REINFORCED.

6. FURRING CHANNELS (OPTIONAL NOT SHOWN) - RESILIENT 20 MSG GALV. STEEL

FURRING CHANNELS SPACED VERT. MAX. 24" O.C. ATTACH FLANGE TO EACH

INTERSECTING STUD WITH 1/2" LONG TYPE S-12 PANHEAD SCREWS.

7. ACOUSTICAL SEALANT.

8. PACKING MATERIAL - MIN. 4" TKNS. OF MIN. 4.0 PCF MINERAL WOOL BATT INSULATION

FIRMLY PACKED INTO FLUTES OF STEEL FLOOR UNITS AS A PERMANENT FORM.

PACKING MATERIAL TO BE RECESSED FROM BOTH SURFACES OF THE WALL AS

REQUIRED TO RECEIVE JOINT SEALANT.

9. JOINT TREATMENT MATERIAL - NON-SAG FIRE CAULK EACH SIDE MIN THICKNESS 1/2",

APPLIED WITHIN THE OPENING BETWEEN THE TOP OF THE WALLBOARD AND ALL

SURFACES OF THE STEEL FLOOR OR STRUCTURE, FLUSH WITH BOTH SURFACES OF

THE WALL ASSEMBLY.

7/

8" M

IN

SMOKETIGHT PARTITION

UL DESIGN #:

STC RATING:

FIRE RATING:

SCALE:

16" O.C.

SECTION

PLAN

3-5/8" STUDD

45 - 49

N.T.S.

DESCRIPTION:

2 43

ABOVE CEILING ID (STENCIL):

"NON-RATED SMOKETIGHT"

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL

DESIGN # MUST BE MET.

WALL PRIORITY:

1/ 4"

M

IN

OPENINGS: SM

1. STEEL FLOOR AND CEILING CHANNELS - TOP AND BOTTOM CHANNELS OF WALL

ASSEMBLY SHALL BE MIN. 20 GA. GALV. STEEL SIZED TO FIT STUDS. TOP CHANNEL TO

HAVE 2" FLANGES (MIN). BOTTOM CHANNEL TO HAVE 1-1/4" FLANGES (MIN). SECURE

BOTTOM CHANNELS WITH STEEL FASTENERS AT 24" O.C. (MAX). SECURE TOP

CHANNELS TO VALLEYS OF STEEL FLOOR UNITS (OR STRUCTURE ABOVE) WITH STEEL

FASTENERS AT 12" O.C. (MAX).

2. STEEL STUDS - MIN. 3-5/8" WIDE (UNLESS NOTED OTHERWISE), 1-1/4" LEGS, 3/8" FOLDED

BACK RETURN. FORMED OF 20 GA.(MIN) GALV. STEEL. MAX. SPACING 16" O.C. CUT

STUDS 1" LESS IN LENGTH THAN ASSEMBLY HEIGHT WITH BOTTOM NESTING IN AND

SECURED TO FLOOR CHANNEL, AND WITH TOP NESTING IN CEILING CHANNEL WITHOUT

ATTACHMENT.

3. SOUND ATTENUATION BATT INSUL. - 3-1/2" (DEPENDING ON STUD SIZE) GLASS FIBER

BATTS IN STUD CAVITY. FILL ENTIRE CAVITY FULL HEIGHT.

4. GYPSUM WALLBOARD- 5/8" THICK TYPE "X", 4' WIDE, ATTACHED TO STEEL STUDS AND

FLOOR CHANNELS WITH 1" LONG TYPE S SELF-TAPPING STEEL SCREWS AT 8" O.C.

ALONG THE VERTICAL AND BOTTOM EDGES AND 12" O.C. IN THE FIELD OF THE BOARD.

INSTALL WALLBOARD WITH A MIN. 1/2" AND MAX. 3/4" GAP BETWEEN THE TOP OF THE

WALLBOARD AND THE BOTTOM OF THE FLOOR UNIT VALLEYS (OR STRUCTURE ABOVE).

NO SCREWS ARE TO BE INSTALLED WITHIN 4" OF THE STEEL FLOOR UNIT VALLEYS AT

THE TOP OF THE WALL. ORIENT JOINTS VERTICALLY AND STAGGER JOINTS ON

OPPOSITE SIDES OF THE ASSEMBLY.

5. JOINT TAPE AND COMPOUND - VINYL, DRY OR PRE-MIXED JOINT COMPOUND, APPLIED

IN TWO COATS TO JOINTS AND SCREW HEADS; PAPER TAPE 2" WIDE EMBEDDED IN

FIRST LAYER OF COMPOUND OVER ALL JOINTS. JOINTS REINFORCED.

6. ACOUSTICAL SEALANT.

7. JOINT TREATMENT MATERIAL - NON-SAG FIRE CAULK EACH SIDE MIN THICKNESS 1/2",

APPLIED WITHIN THE OPENING BETWEEN THE TOP OF THE WALLBOARD AND ALL

SURFACES OF THE STEEL FLOOR OR STRUCTURE, FLUSH WITH BOTH SURFACES OF

THE WALL ASSEMBLY.

V A

R

IE

S

NON-RATED PARTITION

16" O.C.

SECTION

PLAN

E 3-5/8" STUD

F

DESCRIPTION:

2 43

UL DESIGN #:

STC RATING:

FIRE RATING:

SCALE:

45 - 49

N.T.S.

ABOVE CEILING ID (STENCIL):

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL

DESIGN # MUST BE MET.

WALL PRIORITY:

OPENINGS: --

V

A R

IE

S

1. STEEL FLOOR AND CEILING CHANNELS - TOP AND BOTTOM CHANNELS OF WALL

ASSEMBLY SHALL BE MIN. 20 GA. GALV. STEEL SIZED TO FIT STUDS. TOP CHANNEL TO

HAVE 2" FLANGES (MIN). BOTTOM CHANNEL TO HAVE 1-1/4" FLANGES (MIN). SECURE

BOTTOM CHANNELS WITH STEEL FASTENERS AT 24" O.C. (MAX). SECURE TOP

CHANNELS TO VALLEYS OF STEEL FLOOR UNITS (OR STRUCTURE ABOVE) WITH STEEL

FASTENERS AT 12" O.C. (MAX).

2. STEEL STUDS - MIN. 3-5/8" WIDE (UNLESS NOTED OTHERWISE), 1-1/4" LEGS, 3/8" FOLDED

BACK RETURN. FORMED OF 20 GA.(MIN) GALV. STEEL. MAX. SPACING 16" O.C. CUT

STUDS 1" LESS IN LENGTH THAN ASSEMBLY HEIGHT WITH BOTTOM NESTING IN AND

SECURED TO FLOOR CHANNEL, AND WITH TOP NESTING IN CEILING CHANNEL WITHOUT

ATTACHMENT.

3. SOUND ATTENUATION BATT INSUL. - 3-1/2" (DEPENDING ON STUD SIZE) GLASS FIBER

BATTS IN STUD CAVITY. FILL ENTIRE CAVITY FULL HEIGHT.

4. GYPSUM WALLBOARD- 5/8" THICK TYPE "X", 4' WIDE, ATTACHED TO STEEL STUDS AND

FLOOR CHANNELS WITH 1" LONG TYPE S SELF-TAPPING STEEL SCREWS AT 8" O.C.

ALONG THE VERTICAL AND BOTTOM EDGES AND 12" O.C. IN THE FIELD OF THE BOARD.

INSTALL WALLBOARD WITH A MIN. 1/2" AND MAX. 3/4" GAP BETWEEN THE TOP OF THE

WALLBOARD AND THE BOTTOM OF THE FLOOR UNIT VALLEYS (OR STRUCTURE ABOVE).

NO SCREWS ARE TO BE INSTALLED WITHIN 4" OF THE STEEL FLOOR UNIT VALLEYS AT

THE TOP OF THE WALL. ORIENT JOINTS VERTICALLY AND STAGGER JOINTS ON

OPPOSITE SIDES OF THE ASSEMBLY.

5. JOINT TAPE AND COMPOUND - VINYL, DRY OR PRE-MIXED JOINT COMPOUND, APPLIED

IN TWO COATS TO JOINTS AND SCREW HEADS; PAPER TAPE 2" WIDE EMBEDDED IN

FIRST LAYER OF COMPOUND OVER ALL JOINTS. JOINTS REINFORCED.

6. ACOUSTICAL SEALANT.

1/ 4"

M

IN

6" STUD

WALL LEGEND

NOTE: REF. SHEET G01.10 OR WALL TYPE DETAILS

NON-RATED PARTITION

1-HR. RATED FIRE BARRIER

SMOKE BARRIER (1-HR. RATED)

2-HR. RATED EXISTING FIRE BARRIER

NON-RATED SMOKE PARTITION

1-HR. RATED FIRE/SMOKE BARRIER

2-HR. RATED FIRE/SMOKE BARRIER

1 HR SHAFT WALL

INTERIOR WALL TYPE LEGEND

NOTE: REF GENERAL INTERIOR WALL NOTES, WALL

CONSTRUCTION & PRIORITY DETAILS, AND FIREWALL DETAILS

FOR ADDITIONAL INFORMATION. NOT ALL WALLS WILL BE

TAGGED. REFERENCE SECTIONS, DETAILS, & PLAN NOTES FOR

UNIQUE OR SPECIAL CONDITIONS.

A

A

D

E

6" MTL. STUD W/ GYPSUM BOARD ON BOTH SIDES (NON-RATED)

C

6" MTL. STUD W/ GYPSUM BOARD ON (1) SIDES

B

3 5/8" MTL. STUD W/ 2 LAYERS GYPSUM BOARD ON BOTH SIDES

H

F

G

2 1/2" MTL. STUD W/ GYPSUM BOARD ON (1) SIDE

3 5/8" MTL. STUD W/ GYPSUM BOARD ON (1) SIDE

J 7/8" FURRING CHANNELS W/ GYPSUM BOARD ON (1) SIDE

K

L 2 1/2" MTL. STUD W/ GYPSUM BOARD ON ONE SIDE WITH 2" FOIL FACED

RIGID INSULATION AT EXTERIOR WALLS

3 5/8" MTL. STUD W/ GYPSUM BOARD ON BOTH SIDES (1 HOUR FIRE

SMOKE)

3 5/8" MTL. STUD W/ GYPSUM BOARD ON BOTH SIDES (1 HOUR)

3 5/8" MTL. STUD W/ GYPSUM BOARD ON BOTH SIDES (SMOKE)

3 5/8" MTL. STUD W/ GYPSUM BOARD ON BOTH SIDES (NON-RATED)

M 3 5/8" MTL. STUD W/ GYPSUM BOARD ON ONE SIDE WITH 2" FOIL FACED

RIGID INSULATION AT EXTERIOR WALLS

N 1" THICK SHAFT LINER WITH 2 1/2" MTL. SHAFTWALL STUDS AND 5/8"

GYP. BD.

N 1 1/2" MTL. STUD W/ GYPSUM BOARD ON (1) SIDE

SECTION

NON-RATED FURRING

ABOVE CEILING ID (STENCIL):

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL DESIGN

# MUST BE MET.

WALL PRIORITY:

ACOUSTICAL SEALANT

HAT CHANNEL- 7/8" MIN

MTL STUD - 2 1/2"

AT 16" O.C. MAX.

GYPSUM WALLBOARD - 5/8"

THICK TYPE "X"

JOINT TAPE AND COMPOUND

ACOUSTICAL SEALANT

UL DESIGN #:

FIRE RATING:

GA FILE #:

STC RATING: --

OPENINGS: --

DAMPERS: --

CEILING ASSEMBLY

GYPSUM BOARD CUT TO FIT DECK

CONFIGURATION

1/ 4"

M

IN

1/ 4"

M

IN

7/8" HAT CHANNELJ SCALE:

N.T.S.

2 1/2" STUDSK

1 1/2" STUDSN

SECTION

NON-RATED

FURRING WITH

INSULATION

ABOVE CEILING ID (STENCIL):

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL DESIGN

# MUST BE MET.

WALL PRIORITY:

ACOUSTICAL SEALANT

MTL. STUDS

AT 16" O.C. MAX.

GYPSUM WALLBOARD - 5/8"

THICK TYPE "X"

JOINT TAPE AND COMPOUND

ACOUSTICAL SEALANT

UL DESIGN #:

FIRE RATING:

GA FILE #:

STC RATING: --

OPENINGS: --

DAMPERS: --

CEILING ASSEMBLY

GYPSUM BOARD CUT TO FIT

1/ 4"

M

IN

1/ 4"

M

IN

1-5/8" STUDL SCALE:

N.T.S.

2" RIGID INSULATION

3-5/8" STUDM

2HR FIRE BARRIER

UL DESIGN #:

STC RATING:

FIRE RATING:

SCALE:

16" O.C.

SECTION

PLAN

3-5/8" STUDA

U411

55 - 59

2HR

N.T.S.

DESCRIPTION:

2 43

ABOVE CEILING ID (STENCIL):

"2HR FIRE BARRIER"

PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL

DESIGN # MUST BE MET.

WALL PRIORITY:

1/ 4"

M

IN

OPENINGS: 90 MIN

1. STEEL FLOOR AND CEILING CHANNELS - TOP AND BOTTOM CHANNELS OF WALL

ASSEMBLY SHALL BE MIN. 20 GA. GALV. STEEL SIZED TO FIT STUDS. TOP CHANNEL TO

HAVE 2" FLANGES (MIN). BOTTOM CHANNEL TO HAVE 1-1/4" FLANGES (MIN). SECURE

BOTTOM CHANNELS WITH STEEL FASTENERS AT 24" O.C. (MAX). SECURE TOP

CHANNELS TO VALLEYS OF STEEL FLOOR UNITS (OR STRUCTURE ABOVE) WITH STEEL

FASTENERS AT 12" O.C. (MAX).

2. STEEL STUDS - MIN. 3-5/8" WIDE, 1-1/4" LEGS, 3/8" FOLDED BACK RETURN. FORMED OF

20 GA.(MIN) GALV. STEEL. MAX. SPACING 16" O.C. CUT STUDS 1" LESS IN LENGTH THAN

ASSEMBLY HEIGHT WITH BOTTOM NESTING IN AND SECURED TO FLOOR CHANNEL, AND

WITH TOP NESTING IN CEILING CHANNEL WITHOUT ATTACHMENT.

3. SOUND ATTENUATION BATT INSUL. - 3-1/2" (DEPENDING ON STUD SIZE) GLASS FIBER

BATTS IN STUD CAVITY. FILL ENTIRE CAVITY FULL HEIGHT.

4. GYPSUM WALLBOARD- 5/8" THICK TYPE "X", 4' WIDE. OUTER LAYER PAPER OR VINYL

SURFACED. (LAMINATED SYSTEM) WALLBOARD APPLIED VERTICALLY IN TWO LAYERS.

INNER LAYER ATTACHED TO STUDS WITH 1" LONG TYPE 'S' STEEL SCREWS AT 8" O.C.

ALONG VERT. EDGES AND 12" O.C. IN THE FIELD. OUTER LAYER LAMINATED TO INNER

LAYER WITH JOINT COMPOUND APPLIED WITH A NOTCHED SPREADER PRODUCING

CONT. BEADS OF COMPOUND ABOUT 3/8" IN DIAMETER, SPACED NOT MORE THAN 2"

O.C. JOINTS OF LAMINATED OUTER LAYER OFFSET 12" FROM INNER LAYER JOINTS.

OUTER LAYER ATTACHED TO FLOOR CHANNEL WITH 1-5/8" STEEL SCREWS AT 12" O.C.

OPTIONAL (DIRECT ATTACHED SYSTEM) - INNER LAYER ATTACHED TO STUDS WITH 1"

LONG TYPE 'S' STEEL SCREWS AT 16" O.C. ALONG VERT. EDGES AND IN THE FIELD.

OUTER LAYER ATTACHED TO THE STUDS OVER THE INNER LAYER WITH 1-5/8" LONG

TYPE S STEEL SCREWS AT 16" O.C. ALONG VERT. EDGES AND IN THE FIELD AND AT 12"

O.C. TO THE FLOOR CHANNEL. OFFSET OUTER LAYER JOINTS FROM INNER LAYER

JOINTS. OUTER LAYER JOINTS MAY BE TAPED OR UNTAPED. INSTALL WALLBOARD

WITH A MIN. 1/2" AND MAX. 3/4" GAP BETWEEN THE TOP OF THE WALLBOARD AND THE

BOTTOM OF THE FLOOR UNIT VALLEYS. NO SCREWS ARE TO BE INSTALLED WITHIN 4"

OF THE STEEL FLOOR UNIT VALLEYS AT THE TOP OF THE WALL. ORIENT JOINTS

VERTICALLY AND STAGGER JOINTS ON OPPOSITE SIDES OF THE ASSEMBLY. WHEN

ATTACHED TO FURRING CHANNELS, WALLBOARD IS ATTACHED WITH 1" LONG TYPE 'S'

SCREWS AT 12" O.C.

5. JOINT TAPE AND COMPOUND - VINYL, DRY OR PRE-MIXED JOINT COMPOUND, APPLIED

IN TWO COATS TO JOINTS AND SCREW HEADS; PAPER TAPE 2" WIDE EMBEDDED IN

FIRST LAYER OF COMPOUND OVER ALL JOINTS. JOINTS REINFORCED.

6. FURRING CHANNELS (OPTIONAL NOT SHOWN) - RESILIENT 20 MSG GALV. STEEL

FURRING CHANNELS SPACED VERT. MAX. 24" O.C. ATTACH FLANGE TO EACH

INTERSECTING STUD WITH 1/2" LONG TYPE S-12 PANHEAD SCREWS.

7. ACOUSTICAL SEALANT.

8. PACKING MATERIAL - MIN. 4" TKNS. OF MIN. 4.0 PCF MINERAL WOOL BATT INSULATION

FIRMLY PACKED INTO FLUTES OF STEEL FLOOR UNITS AS A PERMANENT FORM.

PACKING MATERIAL TO BE RECESSED FROM BOTH SURFACES OF THE WALL AS

REQUIRED TO RECEIVE JOINT SEALANT.

9. JOINT TREATMENT MATERIAL - NON-SAG FIRE CAULK EACH SIDE MIN THICKNESS 1/2",

APPLIED WITHIN THE OPENING BETWEEN THE TOP OF THE WALLBOARD AND ALL

SURFACES OF THE STEEL FLOOR OR STRUCTURE, FLUSH WITH BOTH SURFACES OF

THE WALL ASSEMBLY.

1/ 8"

M

IN

SECTION

1HR SHAFTWALL

ABOVE CEILING ID (STENCIL):

"1HR FIRE BARRIER"

LIFE SAFETY PLAN DESIGNATION:

GENERAL NOTES:

1. ALL REQUIREMENTS OF LISTED UL DESIGN

# MUST BE MET.

WALL PRIORITY:

JOINT TREATMENT MATERIAL

INSULATION - MIN. 3" MINERAL

WOOL BATTS, FRICTION FITTED TO

FILL CAVITY

VENTED STEEL CH-STUDS- 20

GA,2-1/2" MIN AT 24" O.C.

GYPSUM WALLBOARD - 5/8" THICK

TYPE "X". STAGGER JOINTS

JOINT TAPE AND COMPOUND

STEEL FLOOR J-CHANNELS 1/2"

CONTINUOUS SEALANT PER UL

DESIGN REQUIREMENTS

UL DESIGN #:

FIRE RATING:

U469

1HR

GA FILE #:

STC RATING: 35 - 39

OPENINGS: 45 MIN W/ CLOSER

DAMPERS: FIRE

CEILING ASSEMBLY

STEEL CEILING J-RUNNERS

ACOUSTICAL GASKET AT FLOOR

TRACK

GYPSUM BOARD CUT TO FIT DECK

CONFIGURATION

SHAFT ROOM

1/ 2"

M

IN

5/ 8"

M A

X

GYPSUM SHAFTLINER - 1" THICK

TYPE "X"

3 1/8"

SHAFT WALL STUDN

12 Cadillac Dr., Suite 150 Brentwood, TN 37027 P 615.297.4554

©Copyright 2019

TLC No.:

www.tlc-engineers.com

118626

Drawing Title

Approved: Project Director

Project Title

Date

Location

Checked

Building Number

Project Number

Drawing Number

Drawn

Dwg.

PROJECT TEAM:

Office of

Construction and Facilities Management o n e e ig h th in c h o n e fo o t 1

B

A

C

D

E

F th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t

VA FORM 08-6231

1 2 3 4 5 6 87 9

F

E

D

C

B

A

97 8654321

Department of Veterans Affairs

MURFREESBORO, TN

615.370.8500

615.370.8530 hfrdesign.com

214 Centerview Drive Suite 300 Brentwood, TN 37027

Phase

FULLY SPRINKLERED

C U s e rs \a tr a y lo r\ D o c u m e n ts

\M b o ro V

A W a rd b

R e n o a tr a y lo r2 X

N D

H .r v t

/1

/2

:2

:0

P

M

04-14-2023

626A4-19-101

GI 01.10

AE RENOVATE WARD 1BWALL TYPE DETAILS

AT/MC

HFR Project No: 2019056

100% CONSTRUCTION

DOCUMENTS

● USE SEMI-GLOSS PAINT.

● LOCATE NOT MORE THAN 12'-0" O.C. ON CORRIDOR SIDES OF PARTITIONS, AND WITH A LEAST ONE MESSAGE

PER WALL ON ROOM SIDE OF PARTITION, AND WITHIN 15'-0" OF THE END OF EACH WALL.

● STENCIL MESSAGE SIMILAR TO: "SMOKE PARTITION" OR "1-HR FIRE BARRIER."

● IDENTIFY PARTITIONS ABOVE CEILINGS ON BOTH SIDES OF PARTITIONS EXCEPT WITHIN SHAFTS IN RED

LETTERS NOT LESS THAN 4" HIGH WITH AT LEAST A 3/8" STROKE.

12. FIRE AND SMOKE PARTITION / BARRIER IDENTIFICATION:

11. PENETRATIONS IN WALLS SHALL BE SEALED AS REQUIRED BY THE WALL RATING PER AN APPROVED UL DESIGN.

10. GYPBOARD PANELS SHALL BE PLACED A MINIMUM OF 1/4" ABOVE FLOOR AND SHALL BE CUT WITHIN 1/4" MAX TOLERANCE TO SHAPE OF DECK OR STRUCTURE ABOVE. GAPS BETWEEN PANELS SHALL BE <1/4".

● PROVIDE DEFLECTION AND BRIDGING CLIPS.

● MAINTAIN CLEARANCE UNDER STRUCTURAL BUILDING MEMBERS TO AVOID DEFLECTION TRANSFER TO STUDS.

PROVIDE NESTED OR SLOTTED EXTENDED LEG CEILING TRACK RUNNERS.

9. DO NOT TRANSFER DEFLECTION FROM STRUCTURAL BUILDING MEMBERS TO STUDS. CONTRACTOR'S OPTION, PROVIDE EITHER OF THE FOLLOWING:

8. EXTEND ALL WALL CONSTRUCTION TO THE DECK ABOVE AND SEAL U.N.O.

7. INSTALL ACOUSTICAL GASKETS AT FLOOR AND CEILING TRACK LOCATIONS.

6. PROVIDE ACOUSTICAL INSULATION FULL HEIGHT IN ALL WALLS U.N.O.

5. STAGGER JOINTS ON OPPOSITE SIDES OF PARTITIONS.

4. ALL FRAMING SHALL BE 20 GA U.N.O.

● PROVIDE FIRE RATED IMPACT RESISTANT GYPBOARD 4'-0"H ON ALL WALLS IN PATIENT ROOMS, 4'-0"H AT ALL EQUIPMENT ALCOVES AND ROOMS NOT SCHEDULED TO RECEIVE RIGID WALL PROTECTION, AND ADDITIONAL LOCATIONS AS NOTED ON DRAWINGS. (IMPACT RESISTANT GYPBOARD SHALL TAKE PRIORITY AT LOCATIONS

INDICATED TO RECEIVE GLASS FIBER FACED GYPSUM PANELS.)

● PROVIDE FIRE RATED GLASS FIBER FACED GYPSUM PANELS ON INTERIOR SURFACE OF EXTERIOR WALLS, TOILET ROOMS, JANITOR'S CLOSETS, MECHANICAL SPACES, AND WITHIN 4'-0" OF WATER SOURCES.

● ALL GYPBOARD SHALL BE 5/8" TYPE 'X' U.N.O.

3. GYPBOARD REQUIREMENTS:

2. TOILET WETWALLS AND PATIENT ROOM HEADWALLS SHALL BE 6" METAL STUDS

1. ALL WALLS SHALL BE 3-5/8" METAL STUD AT 16"0.C. MAX U.N.O.

REFERENCE WALL TYPE DETAILS, PLANS, AND SPECIFICATIONS.

GENERAL WALL NOTES

No. Date Description