Attachment 1 (L6) - AR-ETP-25-101_ARTC Cold Wet Jacket_1.1_05Sep2025.pdf

Department of Defense Clothing and Textiles

Style# AR-ETP-25-101

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Scope

Description Scope

This covers the requirements for a waterproof, extreme cold/wet weather jacket, which serves as a layer of the All Range Tactical Clothing System (ARTC).

Design jacket for cold wet environment

Size & Length X Small / Short

X Small / Regular

X Small / Long

X Small / X Long

Small / Short

Small / Regular

Small / Long

Small / X Long

Medium / Short

Medium / Regular

Medium / Long

Medium / X Long

Large / Short

Large / Regular

Large / Long

Large / X Long

X Large / Short

X Large / Regular

X Large / Long

X Large / X Long

9/5/2025 Page 1 of 44

General Statements - Scope Category Description Statements

Classification End Item General Statement The end item(s) shall be of the following types, classes and styles as specified in the contract..

Schedule of sizes End Item General Statement The end items are available in the following sizes as specified in the contract

Size & Length XX Large / Short

XX Large / Regular

XX Large / Long

XX Large / X Long

9/5/2025 Page 2 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Materials Image/Sketch Product Code Description Placement Material Type Total Composition Comments

AR-MTP-25-206 100% Nylon Laminate - PTFE Shell and Reinforcements

Multi Layer Laminated

Nylon 100

AR-MTP-25-207 Three-layer Knit Laminate Facing Multi Layer Laminated

AR-MTP-24-154 Lightweight Nylon Ripstop Hood Brim Drawcord Tunnel Woven

Nylon 100

AR-MTP-25-199 Nylon Spandex Stretch Woven Pocket, Inside Left Woven

Nylon/Spandex 94/6

AR-MTP-25-200 Adhesive Sheet - 2 Layer

Hood Brim, Hood, Hem, Cuff Facing, Cuff Tab, Interior

Pocket, Hand Pockets

Non Woven

AR-MTP-24-143 Lightweight Non-fusible Interlining Center Front Placket Non Woven

AR-MTP-25-201 3 Layer Seam Seal Tape Reinforcement Patches Non Woven

Components

Materials and Components

General Statements - Materials and Components Category Description Statements

Recycled, recovered, or environmentally preferable materials General Statement Recycled, recovered, environmentally preferable, or biobased materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

Requirements General Statement The materials and components shall conform to the requirements specified in material properties in accordance with the Quality Requirements and Inspections Methods.

9/5/2025 Page 3 of 44

Image/Sketch Product Code Description QTY Additional Description Placement Comments

Zipper, No. 8, Type III Style 8 1 30.5 inches Center Front Opening A-A-55634 Type III Grades and Alters see pattern

AR-CTP-24-187 Zipper, No. 5, Type III Style 8 2 10.5 inches Chest Pockets A-A-55634 Type III

AR-CTP-24-187 Zipper, No. 5, Type III Style 8 2 8 inches Arm Pockets A-A-55634 Type III

AR-CTP-24-187 Zipper, No. 5, Type III Style 8 2 29.25 inches Side Zipper A-A-55634 Type III Grades and Alters see pattern

AR-CTP-24-190 Zipper, No. 5, Type I, Style 7 1 7 inches Inside Chest Pocket A-A-55634 Type III Left side only

AR-CTP-24-150 Elastic Drawcord, 3/16" 1 36 inches Hem Center Back Hood Opening & Hood Brim

MIL-DTL-43701 Type II Grades see pattern

AR-CTP-25-265 Cord, Zipper Thong 1 7.5 inches, finishes at 2-3/4 inches Center Front Zipper Pull A-A-55634C Sear Ends

AR-CTP-25-265 Cord, Zipper Thong 6 7.5 inches, finishes at 2-3/4 inches Side Opening Zipper Pull A-A-55634C Sear Ends

AR-CTP-25-265 Cord, Zipper Thong 2 7.5 inches, finishes at 2-3/4 inches Chest Pocket Zipper Pull A-A-55634C Sear Ends

AR-CTP-25-265 Cord, Zipper Thong 2 7.5 inches, finishes at 2-3/4 inches Arm Pocket Zipper Pull A-A-55634C Sear Ends

AR-CTP-24-199 Nylon tape 3/8" width 3 3.25 inches Secure Cordlocks MIL-DTL-5038 Type III Sear Ends

AR-CTP-24-199 Nylon tape 3/8" width 1 3.5 inches Hanger Loop MIL-DTL-5038 Type III Sear Ends

9/5/2025 Page 4 of 44

Label Image/Sketch Product Code Description Material Comments

Components Image/Sketch Product Code Description QTY Additional Description Placement Comments

AR-CTP-24-166 Nylon Fastener Tape, Hook, 1" Width 2 2.5 inches Sleeve Tab A-A-55126 Type II Class 1 Style A

AR-CTP-24-167 Nylon Fastener Tape, Hook, 5/8" Width 4 2 inches Left Center Front Flap A-A-55126 Type II Class 1 Style A

AR-CTP-24-163 Nylon Fastener Tape, Pile, 2" Width 1 2 inches Left Center Front Flap A-A-55126 Class 1 Style A

AR-CTP-24-165 Nylon Fastener Tape, Pile, 1" Width 2 5 inches Sleeve Hem A-A-55126 Class 1 Style A

AR-CTP-24-262 Nylon Fastener Tape, Pile, 5/8" Width 4 2 inches Right Front of Jacket, Hood, Sleeve Yoke, Front A-A-55126 Class 1 Style A

AR-CTP-24-274 CordLoc - Barrel 5 Center Back Hood (1), Hem (2), Hood Brim (2)

AR-CTP-25-278 Two Component Drawcord Ends 3 Center Back Hood (1), Hem Shock Cord (2)

AR-CTP-25-278 Two Component Drawcord Ends 2 Hood Drawcord Ends

AR-CTP-24-208 Snaps (Male Part), No Gloss 2 Side Opening at Hem MIL-DTL-10884 Style 2A Finish

AR-CTP-24-207 Snaps (Female Part), No Gloss 2 Side Opening at Hem MIL-DTL-10884 Style 2A Finish

AR-CTP-24-181 Thread, Nylon, Bonded, Monocord All Top Stitch, All Seams Thread, A-A-59826 Type III Class A

9/5/2025 Page 5 of 44

Label Image/Sketch Product Code Description Material Comments

AR-CTP-24-113 Bar Code Label/Tag Paper

AR-CTP-24-115 Identification and care label

Artwork

Image/Sketch ProductCode Description Artwork type Comments

9/5/2025 Page 6 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Colorways Color Family Color Image/Swatch (Ref)L (Ref)A (Ref)B Comments

Camouflage | 0001 | Army OCP Print |

Material- Colors Image/Sketch Product Code Description Placement Colorway1

AR-MTP-25-206 100% Nylon Laminate - PTFE Shell and Reinforcements 0001 | Army OCP Print |

AR-MTP-25-207 Three-layer Knit Laminate Facing 499 | Tan |

AR-MTP-24-154 Lightweight Nylon Ripstop Hood Brim Drawcord Tunnel 499 | Tan |

AR-MTP-25-199 Nylon Spandex Stretch Woven Pocket, Inside Left 499 | Tan |

AR-MTP-25-200 Adhesive Sheet - 2 Layer Hood Brim, Hood, Hem, Cuff Facing, Cuff Tab, Interior Pocket, Hand Pockets

499 | Tan |

AR-MTP-24-143 Lightweight Non-fusible Interlining Center Front Placket WHT | White |

Colors

General Statements - Colors Category Description Statements

General Statement - Colors End Item The end item(s) shall be in the following color(s) as specified in the contract.

General Statement - Colors Component - Color The color shall be specified in end item

9/5/2025 Page 7 of 44

Component-Colors Image/Sketch Product Code Description Colorway1

Zipper, No. 8, Type III Style 8 499 | Tan |

AR-CTP-24-187 Zipper, No. 5, Type III Style 8 499 | Tan |

AR-CTP-24-187 Zipper, No. 5, Type III Style 8 499 | Tan |

AR-CTP-24-187 Zipper, No. 5, Type III Style 8 499 | Tan |

AR-CTP-24-190 Zipper, No. 5, Type I, Style 7 499 | Tan |

AR-CTP-24-150 Elastic Drawcord, 3/16" 499 | Tan |

AR-CTP-25-265 Cord, Zipper Thong 499 | Tan |

AR-CTP-25-265 Cord, Zipper Thong 499 | Tan |

AR-CTP-25-265 Cord, Zipper Thong 499 | Tan |

AR-CTP-25-265 Cord, Zipper Thong 499 | Tan |

AR-CTP-24-199 Nylon tape 3/8" width 499 | Tan |

AR-CTP-24-199 Nylon tape 3/8" width 499 | Tan |

Material- Colors Image/Sketch Product Code Description Placement Colorway1

AR-MTP-25-201 3 Layer Seam Seal Tape Reinforcement Patches 499 | Tan |

9/5/2025 Page 8 of 44

Label - Colors Image/Sketch Product Code Description

AR-CTP-24-113 Bar Code Label/Tag

AR-CTP-24-115 Identification and care label

Component-Colors Image/Sketch Product Code Description Colorway1

AR-CTP-24-166 Nylon Fastener Tape, Hook, 1" Width 499 | Tan |

AR-CTP-24-167 Nylon Fastener Tape, Hook, 5/8" Width 499 | Tan |

AR-CTP-24-163 Nylon Fastener Tape, Pile, 2" Width 499 | Tan |

AR-CTP-24-165 Nylon Fastener Tape, Pile, 1" Width 499 | Tan |

AR-CTP-24-262 Nylon Fastener Tape, Pile, 5/8" Width 499 | Tan |

AR-CTP-24-274 CordLoc - Barrel 499 | Tan |

AR-CTP-25-278 Two Component Drawcord Ends 499 | Tan |

AR-CTP-25-278 Two Component Drawcord Ends 499 | Tan |

AR-CTP-24-208 Snaps (Male Part), No Gloss 499 | Tan |

AR-CTP-24-207 Snaps (Female Part), No Gloss 499 | Tan |

AR-CTP-24-181 Thread, Nylon, Bonded, Monocord 499 | Tan |

9/5/2025 Page 9 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Label and Artwork Placement

General Statements - Label and Artwork Placement GS Tab Category Description Statements

Label and Artwork Placement Artwork General Statement The artwork shall conform to the requirements listed when examined as specified.

Label and Artwork Placement Label General Statement The label(s) shall conform to the requirements listed when examined as specified.

Label Additional Details

Label Label Placement Measurement Image/Sketch Comments

9/5/2025 Page 10 of 44

Artwork Artwork Placement Measurement Image/Sketch Comments

Artwork Additional Details

9/5/2025 Page 11 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Pattern List Pattern Name Piece Part Cut Parts Material Name comments

PD25_08-MID-HD-INSERT-RNF MIDDLE HOOD INSERT REINFORCEMENT 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SNAP-RNF SNAP REINFORCEMENT 4 100% Nylon Laminate - PTFE (A) Shell

PD25_08-HEM-EYE-SNP-RNF HEM EYELET AND SNAP REINFORCEMENT 4 100% Nylon Laminate - PTFE (A) Shell

PD25_08-BACK BACK 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-ZIP-GUARD ZIPPER GUARD 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-CENTER-HOOD CENTER HOOD 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-BACK-SIDE BACK SIDE 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SIDE SIDE 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SLEEVE-BACK SLEEVE BACK 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SLEEVE-FRONT SLEEVE FRONT 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-UPPER-HOOD UPPER HOOD 2 100% Nylon Laminate - PTFE (A) Shell

Patterns

General Statements - Patterns GS Tab Category Description Detail Statements

Patterns General Statement - Patterns

Standard Standard patterns, providing a seam allowance of ⅜ inch for all seams except where otherwise specified, will be furnished by the Government. The list of pattern parts and computer nomenclature is provided to ensure that the pattern set provided is complete. The Government patterns shall not be altered in any way, and shall only be used for cutting the contractor’s working patterns. The working patterns shall be identical to the Government patterns, except that additional notching, if needed to facilitate manufacture is permitted on the contractor’s working pattern. Minor modifications are permitted where necessary to accommodate the manufacturer’s processes and the use of automated equipment provided the modifications do not alter the dimensional, serviceability, or appearance requirements cited in this document or governed by the Government pattern.

Patterns Component Parts General Statement Component parts shall be cut from the materials specified and in accordance with the pattern parts listed to achieve the desired fit.

9/5/2025 Page 12 of 44

Pattern List Pattern Name Piece Part Cut Parts Material Name comments

PD25_08-FRONT-SIDE FRONT SIDE 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-ZIP-GUARD-TOP ZIPPER GUARD TOP 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SLV-POCKET-EXT SLEEVE POCKET EXTENSION 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-FRONT FRONT 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-LOWER-HOOD LOWER HOOD 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-LEFT-CENTER-FRONT-FLA

P LEFT CENTER FRONT FLAP 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SLEEVE-YOKE SLEEVE YOKE 1 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SLV-TAB SLEEVE TAB 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SIDE-ZIP-FLAP SIDE ZIPPER FLAP 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-SIDE-ZIP-FLAP SIDE ZIPPER FLAP 2 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-FRONT-RIGHT-CHEST-PO

CKET FRONT RIGHT CHEST POCKET 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-HD-CTR-FCG-BTM HOOD CENTER FACING BOTTOM 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-HD-CTR-FCG HOOD CENTER FACING 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-SLV-POCKET-BAG SLEEVE POCKET BAG 2 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-FRONT-HOOD-FACING FRONT HOOD FACING 2 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-HD-TUNNEL HOOD TUNNEL 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-BACK-HEM-FACING BACK HEM FACING 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-SLV-HEM-FCG SLEEVE HEM FACING 2 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-ZIP-GUARD-INNER ZIPPER GUARD INNER 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-CB-PATCH CENTER BACK PATCH 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-CB-PATCH CENTER BACK PATCH 1 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-FRONT-LEFT-CHEST-POC

KET FRONT LEFT CHEST POCKET 1 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-FRONT-HEM-FACING FRONT HEM FACING 2 Three-layer Knit Laminate (C) Knit Laminate

PD25_08-SLV-HEM-ADHESIVE SLEEVE HEM ADHESIVE 2 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-SLV-TAB-ADH SLEEVE TAB ADHESIVE 2 Adhesive Sheet - 2 Layer (B) Adhesive

9/5/2025 Page 13 of 44

Pattern List Pattern Name Piece Part Cut Parts Material Name comments

PD25_08-ZIP-GUARD-ADHESIVE ZIPPER GUARD ADHESIVE 1 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-SIDE-ZIP-FLAP-ADHESIVE SIDE ZIPPER FLAP ADHESIVE 2 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-HD-TUNNEL-ADH HOOD TUNNEL ADHESIVE 1 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-HD-EYE-RNF HOOD EYELET REINFORCEMENT 2 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-HD-EYE-RNF HOOD EYELET REINFORCEMENT 2 100% Nylon Laminate - PTFE (A) Shell

PD25_08-HD-CTR-ADH HOOD CENTER ADHESIVE 1 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-SLV-PKT-BAG-ADH SLEEVE POCKET BAG ADHESIVE 2 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-FRONT-CHEST-PKT-ADH FRONT CHEST POCKET ADHESIVE 2 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-CHEST-TAB-ADH CHEST TAB ADHESIVE 2 Adhesive Sheet - 2 Layer (B) Adhesive

PD25_08-CHEST-INNER-POCKET CHEST INNER POCKET 1 Nylon Spandex Stretch Woven (S) Stretch

PD25_08-HD-CTR-TUNNEL HOOD CENTER TUNNEL 1 Lightweight Nylon Ripstop (D) Ripstop

PD25_08-LEFT-CENTER-FRONT-FLA

P-INT LEFT CENTER FRONT FLAP INTERLINING 1 Lightweight Non-fusible Interlining (I) Interlining

PD25_08-FRONT-CHEST-PKT-PATC

H FRONT CHEST POCKET PATCH 2 3 Layer Seam Seal Tape (E) Seam Seal

Pattern Support Details Pattern Name Piece Part Cut Part Comments Image

9/5/2025 Page 14 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Construction

General Statements - Construction GS Tab Category Description Detail Statements

Construction General Statement - Construction

End Item End item construction shall conform to the requirements and figures to maintain end item configuration as verified by the quality requirements and inspection methods specified. Following the exact sequence of operations is not required, provided the finished end item meets the finished form, fit, and function requirements as those produced by following the sequence of operations.

Construction Seams and Stitches General Statement The end item shall be made in accordance with the stitches and seams specified. The contractor is not required to follow a specific sequence of operations provided the finished end item meets the finished form, fit, and function.

Construction Workmanship End Item General Statement General Statement The finished end item shall be uniform, and the occurrence of defects shall not exceed the established Acceptance Quality Limits (AQL) and shall not adversely affect the serviceability, appearance, and uniformity of the product.

9/5/2025 Page 15 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Construction Images

9/5/2025 Page 16 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Additional Images and Description Image Description

Front detail

Back Detail

9/5/2025 Page 17 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Additional Images and Description Image Description

Sleeve-cuff detail

Hood detail

9/5/2025 Page 18 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Additional Images and Description Image Description

Construction Details Construction Area / Location Description Requirement Image Number

Preparation TRIM PREP SHOCK CORD CUT

INSERT

1. HOT CUT M/C

9/5/2025 Page 19 of 44

Construction Details Construction Area / Location Description Requirement Image Number

FACING

BOTTOM EDGE

6. SET BEMIS FRONT POCKET LINER

BOTTOM

7. SET BEMIS FRONT POCKET BAG

FOLDER

PATCH

11. SET BEMIS FRONT & BACK

GUSSET ZIP

12. SET BEMIS ANCHORED INTO

FACING

In Process Step MAKE SLEEVE TAB &

CUFF

In Process Step HEM FACING 1. SEW HEM FACING EYELET 1. EYELET M/C

BARTACK

5. SET INNER POCKET & FRONT

POCKET BAG

RIPSTOP

9/5/2025 Page 20 of 44

TAPE

TAPE

CORDLOCK

16. INSPECTION

REIN

3. UNDERSRM PANEL & GLUED

SEAMSEAL TAPE

BARTACK

9. SLEEVE POCKET ZIPPER SEAM

SEAL TAPE

SEAL TAPE

SEAM SEAL TAPE

11. FRONT & UNDER SRM PANEL

SEAM

9/5/2025 Page 21 of 44

BARTACK

SEAM SEAL TAPE

CLOSE

12. FRONT & BACK SIDE CLOSE

SEAM SEAL TAPE

13. FRONT & BACK SIDE CLOSE

SEAM

(CORDLOCK)

CLOSE

20. SET BOTTOM HEM 1/8"NYLON

SHOCK CORD

21. SEW HEM FACING FINISHED

CORD BACKTACK

SINGLE

TOPSTITCH

36. N/A

37. N/A

In Process Step FINISHING 1. APPLY VELCRO LOOPS ON

WEARER'S RIGHT SIDE

VELCRO

9/5/2025 Page 22 of 44

Stitches and Seams Seaming

Area/Location Seaming Area

Operation Operation Detail Stitch Type Seam Type Additional Details Stitches Per Inch(SPI) Comments

At all joining seams

301 SSa 9-11

Zipper guards 301 SSae 9-11 no topstitch/edgestitch

Construction Details Construction Area / Location Description Requirement Image Number

Construction Details Secondary Construction Area / Location Description Requirement Image

9/5/2025 Page 23 of 44

Bartacks / Tacks / Backtacks Placement Size(Inches) Stiches Per Inch Number Horizontal Vertical Comments

Jacket Sleeve pocket zipper bottom 3/4 37 STITCHES/TACK 2 þ ¨

Jacket Sleeve pocket zipper top 1/4 37 STITCHES/TACK 4 ¨ þ

Jacket placket 3/8 37 STITCHES/TACK 2 ¨ þ

Jacket CF zipper 1/2 37 STITCHES/TACK 4 ¨ þ

Jacket drawcord pass through 1/4 37 STITCHES/TACK 4 ¨ þ

Jacket Chest Pocket bottom 3/4 37 STITCHES/TACK 2 þ ¨

Jacket Chest Pocket top 1/4 37 STITCHES/TACK 4 ¨ þ

Jacket Inner chest pocket zipper 3/4 37 STITCHES/TACK 2 þ ¨

Jacket side zipper @under arm 3/4 37 STITCHES/TACK 2 þ ¨

Jacket side zipper @hem 3/8 37 STITCHES/TACK 4 ¨ þ

Jacket Hood Brim #00 n/a 4 ¨ ¨ sewn eyelet

Jacket Hood CB #00 n/a 2 ¨ ¨ sewn eyelet

Jacket Hem #00 n/a 4 ¨ ¨ sewn eyelet

Stitches and Seams Seaming

Area/Location Seaming Area

Operation Operation Detail Stitch Type Seam Type Additional Details Stitches Per Inch(SPI) Comments

Hem and hood facing

301 SSae-2 9-11 hem facing: 1-1/8" topstitch up from hem edge

Chest pocket and sleeve pocket bag

301 LSbj-1 9-11 Sleeve Pocket: stitch to shell and then seam seal.

Chest Pocket: secure bottom edge to shell with stitch, then seam seal.

Attaching hook and loop

301 LSbj-1 9-11

Side zippers 301 SSs-1 SSs-1/SSj-1 9-11 1/8 (+/- 1/32) from finished edge

9/5/2025 Page 24 of 44

9/5/2025 Page 25 of 44

9/5/2025 Page 26 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

TOFM & Grade Rules

General Statements -TOFM & Grade Rules GS Tab Category Description Detail Statements

TOFM Finished Dimensions General Statement The finished end item shall conform to the measurements specified in the

Table of Finished Dimensions (TOFM) as defined by the Method of Measure

(MOM).

TOFM Method of Measure General Statement All measurements are taken with garments laid on a flat, clean surface with all folds smooth, being careful not to stretch or distort the garment. All measurements are taken from the front of the garment unless otherwise noted.

9/5/2025 Page 27 of 44

Grade Rules

Code Point of Measure How To Measure Base Tol X Small Small Mediu m Large X

Large

XX

Large

¨ L7S03 HOOD HEIGHT (Long) MEASURED FROM NECK SEAM HPS TO TOP OF THE HOOD

AT FOLD 16 1/4 1/4 0 1/4 0 1/4 3/8 3/8

¨ L7S02 HOOD HEIGHT (Regular) MEASURED FROM NECK SEAM HPS TO TOP OF THE HOOD

AT FOLD 16 1/4 1/4 1/4 1/4 0 1/4 3/8 3/8

¨ L7S01 HOOD HEIGHT (Short) MEASURED FROM NECK SEAM HPS TO TOP OF THE HOOD

AT FOLD 16 1/4 1/4 1/4 1/4 0 1/4 0 0

¨ L7S04 HOOD HEIGHT (XLong) MEASURED FROM NECK SEAM HPS TO TOP OF THE HOOD

AT FOLD 16 7/8 1/4 0 0 0 0 0 3/8

¨ L7T07 HOOD WIDTH AT WIDEST POINT - ON HALF

(Long)

MEASURED STRAIGHT FROM MIDDLE OF FLAP STITCH LINE

AT FOLD EDGE TO BRIM JOINING SEAM 11 3/4 3/8 0 3/8 0 1/2 1/2 1/2

¨ L7T06 HOOD WIDTH AT WIDEST POINT - ON HALF

(Regular)

MEASURED STRAIGHT FROM MIDDLE OF FLAP STITCH LINE

AT FOLD EDGE TO BRIM JOINING SEAM 11 3/4 3/8 3/8 3/8 0 1/2 1/2 1/2

¨ L7T05 HOOD WIDTH AT WIDEST POINT - ON HALF

(Short)

MEASURED STRAIGHT FROM MIDDLE OF FLAP STITCH LINE

AT FOLD EDGE TO BRIM JOINING SEAM 11 3/4 3/8 3/8 3/8 0 1/2 0 0

¨ L7T08 HOOD WIDTH AT WIDEST POINT - ON HALF

(XLong)

MEASURED STRAIGHT FROM MIDDLE OF FLAP STITCH LINE

AT FOLD EDGE TO BRIM JOINING SEAM 12 3/4 3/8 0 0 0 0 0 1/2

¨ L3S15 CENTER FRONT LENGTH (Long) Measurement taken straight from CF at neck seam to lowest point at finished hem edge 26 1/2 1/2 0 1/2 0 1/2 1/2 1/2

¨ L3S14 CENTER FRONT LENGTH (Regular) Measurement taken straight from CF at neck seam to lowest point at finished hem edge 25 1/2 1/2 1/2 1/2 0 1/2 1/2 1/2

¨ L3S13 CENTER FRONT LENGTH (Short) Measurement taken straight from CF at neck seam to lowest point at finished hem edge 24 1/2 1/2 1/2 1/2 0 1/2 0 0

¨ L3S16 CENTER FRONT LENGTH (X Long) Measurement taken straight from CF at neck seam to lowest point at finished hem edge 28 1/2 1/2 0 0 0 0 0 1/2

¨ L6T03 LONG SLEEVE LENGTH (Long) LAY FLAT / MEASURE ALONG FOLD EDGE FROM HPS TO

SLEEVE HEM EDGE 34 1/2 1/2 0 7/8 0 7/8 7/8 7/8

¨ L6T02 LONG SLEEVE LENGTH (Regular) LAY FLAT / MEASURE ALONG FOLD EDGE FROM HPS TO

SLEEVE HEM EDGE 33 1/2 7/8 7/8 0 7/8 7/8 7/8

¨ L6T01 LONG SLEEVE LENGTH (Short) LAY FLAT / MEASURE ALONG FOLD EDGE FROM HPS TO

SLEEVE HEM EDGE 32 1/2 7/8 1 3/8 0 3/8 0 0

¨ L6T04 LONG SLEEVE LENGTH (XLong) LAY FLAT / MEASURE ALONG FOLD EDGE FROM HPS TO

SLEEVE HEM EDGE 37 3/4 1/2 0 0 0 0 0 7/8

Department of Defense Clothing and Textiles

Style# AR-ETP-25-101

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Grade Rule Size Range Alpha Sizes XXS-4XL | Fit Type

Selected Sizes X Small|Small|Medium|Large|X Large|XX Large

Base Size Medium

9/5/2025 Page 28 of 44

Small Small Mediu m Large X

Large

XX

Large

¨ L7T32 LONG SLEEVE OPENING WIDTH - ON HALF

(Long)

MEASURE STRAIGHT FROM FOLD EDGE TO EDGE AT

FINISHED SLEEVE OPENING 6 3/8 1/4 0 1/4 0 3/8 3/8 3/8

¨ L7T31 LONG SLEEVE OPENING WIDTH - ON HALF

(Regular)

MEASURE STRAIGHT FROM FOLD EDGE TO EDGE AT

FINISHED SLEEVE OPENING 6 3/8 1/4 1/4 1/4 0 3/8 3/8 3/8

¨ L7T30 LONG SLEEVE OPENING WIDTH - ON HALF

(Short)

MEASURE STRAIGHT FROM FOLD EDGE TO EDGE AT

FINISHED SLEEVE OPENING 6 3/8 1/4 1/4 1/4 0 3/8 0 0

¨ L7T33 LONG SLEEVE OPENING WIDTH - ON HALF

(XLong)

MEASURE STRAIGHT FROM FOLD EDGE TO EDGE AT

FINISHED SLEEVE OPENING 7 1/8 1/4 0 0 0 0 0 3/8

¨ L7T37 CHEST WIDTH - ON HALF (Long)

MEASURED STRAIGHT FROM FOLD EDGE TO EDGE AT 1"

BELOW ARMHOLE SEAM WITH GARMENT LYING FLAT AND

CENTER FRONTAND SIDE SEAM ZIPPERS FULLY CLOSED

26 1/4 1/2 0 2 0 2 2 2

¨ L7T18 CHEST WIDTH - ON HALF (Regular)

MEASURED STRAIGHT FROM FOLD EDGE TO EDGE AT 1"

BELOW ARMHOLE SEAM WITH GARMENT LYING FLAT AND

CENTER FRONTAND SIDE SEAM ZIPPERS FULLY CLOSED

26 1/4 1/2 2 2 0 2 2 2

¨ L7T35 CHEST WIDTH - ON HALF (Short)

MEASURED STRAIGHT FROM FOLD EDGE TO EDGE AT 1"

BELOW ARMHOLE SEAM WITH GARMENT LYING FLAT AND

CENTER FRONTAND SIDE SEAM ZIPPERS FULLY CLOSED

26 1/4 1/2 2 2 0 2 0 0

¨ L7T20 CHEST WIDTH - ON HALF (XLong)

MEASURED STRAIGHT FROM FOLD EDGE TO EDGE AT 1"

BELOW ARMHOLE SEAM WITH GARMENT LYING FLAT AND

CENTER FRONTAND SIDE SEAM ZIPPERS FULLY CLOSED

30 1/4 1/2 0 0 0 0 0 2

¨ L7T23 BOTTOM OPENING - ON HALF (Long)

MEASURED STRAIGHT FROM HEM FOLD EDGE TO EDGE

WITH GARMENT LYING FLAT, CENTER FRONTAND SIDE

SEAM ZIPPERS FULLY CLOSED AND INNER SIDE PLEATS

FOLD FLAT

23 1/2 0 2 0 2 2 2

¨ L7T22 BOTTOM OPENING - ON HALF (Regular)

MEASURED STRAIGHT FROM HEM FOLD EDGE TO EDGE

WITH GARMENT LYING FLAT, CENTER FRONTAND SIDE

SEAM ZIPPERS FULLY CLOSED AND INNER SIDE PLEATS

FOLD FLAT

23 1/2 2 2 0 2 2 2

¨ L7T21 BOTTOM OPENING - ON HALF (Short)

MEASURED STRAIGHT FROM HEM FOLD EDGE TO EDGE

WITH GARMENT LYING FLAT, CENTER FRONTAND SIDE

SEAM ZIPPERS FULLY CLOSED AND INNER SIDE PLEATS

FOLD FLAT

23 1/2 2 2 0 2 0 0

¨ L7T24 BOTTOM OPENING - ON HALF (XLong)

MEASURED STRAIGHT FROM HEM FOLD EDGE TO EDGE

WITH GARMENT LYING FLAT, CENTER FRONTAND SIDE

SEAM ZIPPERS FULLY CLOSED AND INNER SIDE PLEATS

FOLD FLAT

27 1/2 0 0 0 0 0 2

¨ L3S53 CENTER BACK BODY LENGTH (Long) Measurement taken straight from center back neck seam to folded hem edge at lowest point of drop tial at center back

33 1/4 1/2 0 1/2 0 1/2 1/2 1/2

¨ L3S52 CENTER BACK BODY LENGTH (Regular) Measurement taken straight from center back neck seam to folded hem edge at lowest point of drop tial at center back

32 1/4 1/2 1/2 1/2 0 1/2 1/2 1/2

¨ L3S51 CENTER BACK BODY LENGTH (Short) Measurement taken straight from center back neck seam to folded hem edge at lowest point of drop tial at center back

31 1/4 1/2 1/2 1/2 0 1/2 0 0

¨ L3S54 CENTER BACK BODY LENGTH (XLong) Measurement taken straight from center back neck seam to folded hem edge at lowest point of drop tial at center back

35 1/4 1/2 0 0 0 0 0 1/2

¨ L3S01 Collar Height at Center Front Measurement taken at center front from collar seam to top of bendback. 4 1/8 0 0 0 0 0 0

¨ L7T29 BICEP WIDTH -ON HALF - ON HALF (XLong)

MEASURE STRAIGHT FROM FOLD EDGE OF UNDERARM

SEAM AT 1" BELOW ARMHOLE TO FOLDED TOP EDGE OF

SLEEVE

13 1/4 0 0 0 0 0 1/2

¨ L7T28 BICEP WIDTH -ON HALF- ON HALF (Long)

MEASURE STRAIGHT FROM FOLD EDGE OF UNDERARM

SEAM AT 1" BELOW ARMHOLE TO FOLDED TOP EDGE OF

SLEEVE

12 1/4 0 1/2 0 1/2 1/2 1/2

9/5/2025 Page 29 of 44

Small Small Mediu m Large X

Large

XX

Large

¨ L7T27 BICEP WIDTH- ON HALF - ON HALF (Regular)

MEASURE STRAIGHT FROM FOLD EDGE OF UNDERARM

SEAM AT 1" BELOW ARMHOLE TO FOLDED TOP EDGE OF

SLEEVE

12 1/4 1/2 1/2 0 1/2 1/2 1/2

¨ L7T26 BICEP WIDTH- ON HALF - ON HALF (short)

MEASURE STRAIGHT FROM FOLD EDGE OF UNDERARM

SEAM AT 1" BELOW ARMHOLE TO FOLDED TOP EDGE OF

SLEEVE

12 1/4 1/2 1/2 0 1/2 0 0

Additional TOFM Details

Code Point Of Measure How to Measure Tol Base Size Grade

9/5/2025 Page 30 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

General Statements - Inspection Methods Category Description Detail Statements

Inspection Methods End Item General Statement General Statement Finished end items shall be inspected in accordance with the inspection methods specified and those referenced specifications and standards unless otherwise excluded, amended, or modified in this specification or applicable procurement documents

Inspection Methods Testing End item General Statement General Statement Finished end items shall be examined and tested in accordance with the specified examinations and tests on the end item properties unless otherwise excluded, amended, or modified in this document or applicable procurement documents. End item physical tests apply to the finished end item to include all pre and post treatments, assemblies and operations.

General Statements - Conformance Category Description Detail Statements

Conformance Inspection Requirement General Statement Samples shall be subjected to Conformance inspections for compliance with design, configuration, workmanship, dimensional and testing requirements. Conformance inspection shall consist of the inspection methods, examinations and tests specified.

Conformance Inspection End Item Acceptance Criteria General Statement Acceptance quality limits (AQL) as specified in the contract and/or order, except where otherwise indicated.

Conformance Inspection End Item Sampling General Statement Sampling for inspection shall be performed in accordance with ASQ/ANSI Z1.4. The sample shall be one (1) end item and the lot size shall be expressed in units of end items.

Quality

General Statements - First Article Category Description Detail Statements

First Article Inspection - Quality

Requirement General Statement Samples shall be subjected to First Article inspection for compliance with design, configuration, workmanship, dimensional and testing requirements. First article inspection shall consist of the inspection methods, examinations and tests specified.

First Article Inspection - Quality

Acceptance Criteria General Statement The presence of defects exceeding AQLs specified in the contract or failure of any testing (end item, material or component) shall be cause for rejection of the first article.

First Article Inspection - Quality

Sampling General Statement The sample size shall be as specified in the contract. The sample unit shall be one finished end item and the lot size shall be expressed in units of end items.

Additional Quality General Statements Category Description Detail Statement

9/5/2025 Page 31 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Material Properties and Testing Requirements are to be found within the Material and Components identified.

End Item Properties and testing are to be found within End Item Testing

GENERAL STATEMENTS - MATERIAL AND COMPONENTS PHYSICAL REQUIREMENT

GS Tab Category Description Detail Statement

Material Properties and Testing Physical Requirements - Material Properties and Testing

End Item General Statement General Statement The end item shall conform to the requirements listed when tested as specified.

Material Properties and Testing Component Standard Samples General Statement The finished component shall match the standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced.

Material Properties and Testing Material Standard Samples General Statement The finished material shall match the standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced.

9/5/2025 Page 32 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Additional End Item Properties & Testing Requiremnts

Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

End Item Testing

Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

Dimensional Stability 50 washes, warp %|Percentage Maximum 3.0 American Association of Textile Chemist and Colorists

(AATCC)

AATCC TM150|Dimensional Changes of Garments after Home Laundering|3363|

Dimensional Stability 50 washes, fill %|Percentage Maximum 2.5 American Association of Textile Chemist and Colorists

(AATCC)

AATCC TM150|Dimensional Changes of Garments after Home Laundering|3363|

Dimensional Stability 100 washes, warp %|Percentage Maximum 3.5 American Association of Textile Chemist and Colorists

(AATCC)

AATCC TM150|Dimensional Changes of Garments after Home Laundering|3363|

Dimensional Stability 100 washes, fill %|Percentage Maximum 2.5 American Association of Textile Chemist and Colorists

(AATCC)

AATCC TM150|Dimensional Changes of Garments after Home Laundering|3363|

Toxicity The finished end item shall not present a health hazard and shall show compatibility with prolonged, direct skin contact, as specified in 40 CFR §798.2250, Dermal Toxicity, and 40 CFR §798.4100, Dermal Sensitization. Chemicals recognized by the Environmental Protection Agency as human carcinogens shall not be used.

Department of Defense - Internal

ITP6|Toxicity|3363| If dermal toxicity testing is required, it will be conducted in accordance with Title 40 of the Code of Federal Regulations, current editions and applicable sections, which are consistent with OECD tests: Skin Sensitization 406 and Dermal Irritation 404 (https://www.oecd-ilibrary.org/environment/oecd-g uidelines-for-the-testing-of -chemicals-section-4-health-effects_20745788?pa ge=1). Dermal sensitization:

https://www.law.cornell.edu/cfr/text/40/798.4100 Dermal toxicity:https://www.law.cornell.edu/cfr/text/40/798.

End Item Testing

General Statements - End Item Testing Category Description Detail Statements

Physical Requirements - End Item Testing

General Statement The finished end item shall conform to the requirements listed when tested as specified.

9/5/2025 Page 33 of 44

Additional End Item Properties & Testing Requiremnts

Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

Sealed Seams The seam tape shall be launderable and shall prevent water leakage through seams and stitching. Seam tape shall be applied only to the inside of the end item.

Tape shall be cut 7/8-inch to 1-inch wide strips from material that is compatible with the back side of cloth specified in Table I. The shade of the tape shall approximate the back of the basic cloth.

ASTM International ASTM D751 Standard Test Method for Coated Fabrics

The end item shall be tested for initial hydrostatic resistance in accordance with ASTM D751 Procedure B, Procedure 2 as follows: Tests shall be run on the finished jacket at five (5) different seam locations as follows: One (1) on each side seam, one (1) on the center hood seam, and two

(2) on the seam joining the hood to the neck of the jacket. The five (5) determinations shall be reported separately as "pass" or "fail". More than one (1) area of the five (5) test areas on each jacket showing leakage shall constitute a failure.

Sealed Seams Hydrostatic Resistance After Laundering

No Leakage ASTM International ASTM D751 Standard Test Method for Coated Fabrics

From production lots when specified, units shall be randomly selected for five (5) launderings in accordance with the laundering procedure below.

The units shall be visually examined and then tested for hydrostatic resistance as specified in ASTM D751, Procedure B, Procedure 2, after the fifth laundering cycle.

Sealed Seams Hydrostatic Resistance No Leakage ASTM International ASTM D751 Standard Test Method for Coated Fabrics

ASTM D751, Procedure B, Procedure 2 shall be utilized to determine if the seams are resistant to leakage at a fixed hydrostatic head pressure of 50 centimeters for three (3) minutes. The hydrostatic pressure shall be applied to the outside or face of the garment. Leakage is defined as the appearance of water at three (3) or more different places or the continuous flow of water through the material or seams at one (1) or more different places within the 4-1/2-inch diameter test area.

Sealed Seams End Item Laundering for sealed seam test

Prior to laundering, one (1) jacket shall be retained for use as the unlaundered sample in evaluating the jackets after laundering. Place two (2) end items, (one (1) end item may be ballast) (approximately 4 pounds total load), in an automatic washing machine set on permanent press cycle, high water level and warm 100°F (+ 10°F, - 0°F) wash temperature. If seams are taped sealed, then taped areas of the end item shall be visually examined prior to laundering for physical surface appearance characteristics and initial tape end and integrity conditions. The slide, hook/loop and snap fasteners of each end item shall be closed with the right side of each end item out during the wash and drying cycles. Place 28 grams of detergent conforming to 1993 AATCC Standard Reference Detergent (non-phosphate) without optical brighteners into the washer. The duration of each laundering cycle shall be 30 to 35 minutes.

After laundering, place end items in an automatic tumble dryer set on permanent press cycle, high heat setting (150°F -160°F) and run approximately for 45 minutes. Conduct five (5) laundering and drying cycles. After the fifth laundering and drying cycle, test and evaluate the end items for conformance to the required characteristics in this table. The laundering equipment (washer and dryer) shall be in accordance with AATCC-135.

9/5/2025 Page 34 of 44

Material Properties Color

Color Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

Additional End Item Properties & Testing Requiremnts

Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

Sealed Seams Appearance After Laundering

After five (5) laundering cycles, the end item shall be examined for any sign of tape ends lifting, within 3/4-inch of sewn seam; tape ends lifting more than 1/8-inch when tape extends beyond 3/4-inch of the sewn seam, tape curling, bubbling, separation along tape edges or across the tape width, or tape outer layer more than 1/8-inch. The occurrence of any of these defects shall be considered a test failure. Tape ends lifting more than 1/8-inch beyond 3/4-inch of the sewn seam shall be tested for hydrostatic resistance in accordance with ASTM D751 Procedure B, Procedure 2. Color loss in print areas of camouflage pattern. After five (5) laundering cycles, the color loss shall be determined by comparing the laundered and unlaundered samples. Any color change on any area of the end item less than the required rating on the AATCC Gray Scale for evaluating change in color shall be considered a test failure. Any physical surface appearance characteristic noted in a taped area on the unlaundered sample shall not be considered a test failure on the laundered end item if there is no adverse change in the characteristic. Puckering and creases within taped areas, not adversely affecting appearance shall not be considered a test failure. Physical surface appearance changes of the basic shell material. After five (5) laundering cycles, the camouflage face side of the end item shall be visually examined on all visible pattern parts for any evidence of physical surface appearance changes as unlaundered sample. Any physical surface appearance change shall be considered a test failure. Any physical surface appearance characteristic noted in a taped area on the unlaundered end item, if seams are tape sealed, shall not be considered a test failure on the laundered end item if there is no adverse change in the characteristic. Puckering and creases within taped areas, not adversely affecting appearance shall not be considered a test failure.

9/5/2025 Page 35 of 44

Material Properties Color

Color Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

Visual Shade Matching The color and appearance of the end item shall match the standard sample when viewed using the AATCC EP 9, Option C, with a primary light source simulating the spectral quality of average daylight, CIE Illuminant D65, with a color temperature of 6500 (± 200) Kelvin (K) illumination of 100 (± 20) foot candles. Alternatively, the color and appearance of the end item shall match the standard sample with a primary light source simulating artificial daylight, CIE Illuminant D75, with a color temperature of 7500K (± 200) illumination of 100 (± 20) foot candles in lieu of D65. The end item shall also be a good match to the standard sample with a secondary source simulating the spectral quality of incandescent lamplight, CIE Illuminant A, with a color temperature of 2856K (± 200).

American Association of Textile Chemist and Colorists

(AATCC)

AATCC EP9|Evaluation Procedure for Visual Assessment of Color Difference of Textile|3363|

Option C

9/5/2025 Page 36 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Internal Test Procedures

Internal Test Procedures- Style Source Test Method Test method options Test method description

Department of Defense - Internal

ITP6|Toxicity|3363| If dermal toxicity testing is required, it will be conducted in accordance with Title 40 of the Code of Federal Regulations, current editions and applicable sections, which are consistent with OECD tests: Skin Sensitization 406 and Dermal Irritation 404 (https://www.oecd-ilibrary.org/environment/oecd-guidelines-for-the-testing-of -chemicals-section-4-health-effects_20745788?page=1). Dermal sensitization:

https://www.law.cornell.edu/cfr/text/40/798.4100 Dermal toxicity:https://www.law.cornell.edu/cfr/text/40/798.2250

9/5/2025 Page 37 of 44

Description All Range Tactical Clothing (ARTC) - Cold Wet Jacket

MIL/CID Number N/A

Style Status

Platform Combat

Environment Cold Weather

End Use

Gender Unisex

Enterprise DoD | 01

Service AR | Army

Category APP | Apparel

Sub Category Jacket and Coats |

Size Range Alpha Sizes XXS-4XL |

Defects End Item

Item Defect Category NOs Defect Additional Detail Measurements Major Minor

1 Jackets Material 01 Hole, cut, tear, smash, burn, drill hole, run, needle chew, abrasion damaging the fabric, affecting appearance or serviceability þ ¨

2 Jackets Cutting 02 Any component part not cut in accordance with specified directional lines, twill lines and/or fabric grain not parallel between parts þ ¨

3 Jackets Components 03 Component omitted þ ¨

4 Jackets Components 04 Component bent, broken, cracked, torn, cut, twisted, folded or scratched þ ¨

5 Jackets Stitching and Seaming 05 Omitted þ ¨

6 Jackets Stitching and Seaming 06 Seam and/or stitch type not as specified þ ¨

7 Jackets Bartacks 07 Omitted þ ¨

8 Jackets Bartacks 08 Loose and or tight stitch tension ¨ þ

9 Jackets Labels 09 Label text incorrect, incomplete and/or illegible (smeared or bleeding) þ ¨

10 Jackets Labels 10 Omitted þ ¨

11 Jackets Hem(s) 11 Not finished as specified þ ¨

12 Jackets Hem(s) 12 Hem twisted, pleated and/or puckered þ ¨

13 Jackets Hem(s) 13 Irregular in width þ ¨

14 Jackets Cleanliness 14 Any spot and/or stain on outside that cannot be completely removed with a clean cloth moistened with water ¨ ¨

15 Jackets Cleanliness 15 Thread ends on the outside of the garment ¨ ¨

Defects

General Statements- Defects Category Description Detail Statement

1 Quality End Item General Statement General Statement The finished end item shall be examined and scored for the defects listed.

9/5/2025 Page 38 of 44

Defects End Item

Item Defect Category NOs Defect Additional Detail Measurements Major Minor

16 Jackets Sleeve and armholes 16 Sleeves not attached as specified þ ¨

17 Jackets Sleeve and armholes 17 Sleeves reversed þ ¨

18 Jackets Sleeve and armholes 18 Sleeves tight, causing pleat and/or excessive puckers on front, back and/or sleeve ¨ þ

Additional defects Part NOS Defect Major Minor

1 Material and Components 16 Incorrect, not as specified. þ ¨

2 Material and Components 17 Knots greater than Fabric Defect Scale Level C. ¨ þ

3 Material and Components 18 Slubs greater than Fabric Defect Scale Level D. ¨ þ

4 Construction, Assemby and Workmanship 19 Any component or part omitted (unless classified herein). þ ¨

5 Material and…