Attachment 1 (L1) - AR-MTP-23-203_Cloth_Mesh Knit_1.1_05Sep2025.pdf

Department of Defense Clothing and Textiles

RM # AR-MTP-23-203

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Year 2023

RM Status

Size Range zRM - Rolled Goods |

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

General Statements - Scope Category Description Statements

Approved Use All Departments and Agencies General Statement This document is approved for use by all Departments and Agencies of the Department of Defense (DoD).

Classification Component General Statement The component (s) shall be of the following types, classes and styles as specified in the contract..

Scope

9/4/2025 Page 1 of 15

Fabric# AR-MTP-23-203

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Style Colors Color Swatch (Ref)L (Ref)A (Ref)B Comments

476/498 | Coyote | 45.44 4.66 15.18

General Statements - Colors Category Description Statements

General Statement - Colors Material The fabric(s) shall be in the following color(s) as specified in the contract.

Colors

9/4/2025 Page 2 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

General Statements - Material Construction GS Tab Category Description Detail Statements

Construction General Statement - Construction

Material and Component Material construction shall conform to the requirements specified as verified by the quality requirements and inspection methods specified. Following the exact sequence of operations is not required, provided the finished material meets the physical requirements and appearance as those produced by following the sequence of operations.

Construction Workmanship Material General Statement General Statement The finished end item shall be uniform, and the occurrence of defects shall not exceed the established Acceptance Quality Limits (AQL) and shall not adversely affect the serviceability, appearance, and uniformity of the product.

Material Construction

Yarn Ply Single

Yarn Details Modacrylic/rayon

Fiber Percentage Yarn 1 Yarn

Total Composition

Fiber Percentage Yarn 2 Yarn

Total Composition B

Fiber/Yarn/Additional Details Modacrylic and Rayon blend

Woven Information

Weave Type

Warp Count

Weft Count

Knit Information

Knit Type Mesh

Gauge

Wales

General Information

Fabric Weight 3.0-3.8

UOM Oz/yd2|Ounces per square yard

Width 0

9/4/2025 Page 3 of 15

Additional Construction Details Image Description

Open Hole, net-like warp knit mesh construction

Material Finish / Treatment Material Finish / Treatment Additional Details

Untreated

UOM

Thickness (inches) 0.02

Appearance/Hand

Courses Shinkage Length 0

UOM

Shirinkage Width 0

UOM

9/4/2025 Page 4 of 15

Style# AR-MTP-23-203

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Style Status

Platform

Environment

End Use

Gender

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

General Statements - Inspection Methods Category Description Detail Statements

Inspection Methods Inspection Conditions General Statement General Statement The end item shall be examined for defects in color, shade, design, material, finish, construction, workmanship, marking, and the defects shall be classified in accordance with the list of defects.

General Statements - Conformance Category Description Detail Statements

Conformance Inspection Requirement General Statement Samples shall be subjected to Conformance inspections for compliance with design, configuration, workmanship, dimensional and testing requirements. Conformance inspection shall consist of the inspection methods, examinations and tests specified.

Conformance Inspection Material and Component Sampling Unless otherwise specified in subsidiary specifications, referenced documents, or procurement documents material and component sampling shall be (2) sample units for lots 800 yards of less, (3) sample units for lots 801 yards to 22,000 yards and (4) sample units for lots over 22,000 yards. For material testing, the sample unit shall be 5 continuous yards full width of the finished cloth for all physical and chemical tests.

Conformance Inspection Material and Component Acceptance Criteria The lot shall be unacceptable if the number of defects exceeds the Acceptable Quality Limits (AQL) or the failure of any test.

Quality

General Statements - First Article Category Description Detail Statements

First Article Inspection - Quality

Acceptance Criteria General Statement The presence of defects exceeding AQLs specified in the contract or failure of any testing (end item, material or component) shall be cause for rejection of the first article.

First Article Inspection - Quality

Requirement General Statement Samples shall be subjected to First Article inspection for compliance with design, configuration, workmanship, dimensional and testing requirements. First article inspection shall consist of the inspection methods, examinations and tests specified.

First Article Inspection - Quality

Sampling General Statement The sample size shall be as specified in the contract. The sample unit shall be one finished end item and the lot size shall be expressed in units of end items.

Additional Quality General Statements Category Description Detail Statement

9/4/2025 Page 5 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Material Properties

Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

1 Hole (void) Size relaxed PSI|Per square inch

30-55 visual

2 Hole (void) Size relaxed mm|Millimeters Minimum 1.6 Department of Defense - Internal ITP2|Hole Size Determination|3363|

3 Fiber Content Modacrylic/Rayon American Association of Textile Chemist and Colorists (AATCC)

AATCC TM20|Fiber Analysis:

Qualitative|3363|

Weight Oz/yd2|Ounces per square yard 3.0-3.8 ASTM International ASTM D3776 / D3776M|Standard Test

Methods for Mass Per Unit Area (Weight) of Fabric|3363| method C

5 Thickness in|Inches Minimum 0.02 ASTM International ASTM D1777|Standard Test Method for Thickness of Textile Materials|3363|

Snag Test courses and wales Minimum 4 ASTM International ASTM D3939 / D3939M|Standard Test

Method for Snagging Resistance of Fabrics (Mace)|3363|

Pilling rating Minimum 4 ASTM International ASTM D3512 / D3512M|Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Random Tumble Pilling Tester|3363|

8 Drying Time 95% min|Minutes Maximum 90 Department of Defense - Internal ITP8|Dry Time - Fabric|6487|

Material Properties and Testing

General Statements - Material Component and Physical Requirements Gs Tab Category Description Detail Statements

Material Properties and Testing

Component Standard Samples

General Statement The finished component shall match the standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced.

Material Properties and Testing

Material Standard Samples General Statement The finished material shall match the standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced.

Material Properties and Testing

Physical Requirements - Material Properties and Testing

Material General Statement General Statement The finished material shall conforms to the requirements listed when tested as specified.

9/4/2025 Page 6 of 15

Material Properties

Characteristic Characteristic Additional Detail UOM Min/Max Requirements Source Test method Test Method Options

Labile Sulfur Content The use of dyes and compounds containing sulfur capable of oxidation to sulfuric acid shall be chosen and applied such that the dyed and finished cloth shall show a rating of “slight” or “free” labile sulfur.

Department of Defense - Internal ITP5|Labile Sulfur|3363|

10 Dimensional Stability 3 cycles, wales %|Percentage Maximum 5 American Association of Textile Chemist and Colorists (AATCC)

AATCC TM135|Dimensional Changes of Fabrics after Home Laundering|3363|

(1), III, (Ai)

11 Dimensional Stability 3 cycles, courses %|Percentage Maximum 12 American Association of Textile Chemist and Colorists (AATCC)

AATCC TM135|Dimensional Changes of Fabrics after Home Laundering|3363|

(1), III, (Ai)

Fabric Stretch wales %|Percentage Minimum 20 ASTM International ASTM D2594 / D2594M|Standard Test

Method for Stretch Properties of Knitted Fabrics Having Low Power|3363|

Loose Fitting Items procedure & conditioning

Fabric Stretch courses %|Percentage Minimum 25 ASTM International ASTM D2594 / D2594M|Standard Test

Method for Stretch Properties of Knitted Fabrics Having Low Power|3363|

Loose Fitting Items procedure & conditioning

Fabric Growth wales %|Percentage Maximum 5 ASTM International ASTM D2594 / D2594M|Standard Test

Method for Stretch Properties of Knitted Fabrics Having Low Power|3363|

Loose Fitting Items procedure & conditioning

Fabric Growth courses %|Percentage Maximum 10 ASTM International ASTM D2594 / D2594M|Standard Test

Method for Stretch Properties of Knitted Fabrics Having Low Power|3363|

Loose Fitting Items procedure & conditioning

Vertical Flame initial and after 5 launderings, wales No melt/no drip ASTM International ASTM D6413 / D6413M|Standard Test

Method for Flame Resistance of Textiles (Vertical Test)|3363|

Vertical Flame initial and after 5 launderings, courses No melt/no drip ASTM International ASTM D6413 / D6413M|Standard Test

Method for Flame Resistance of Textiles (Vertical Test)|3363|

18 pH - Water Extract 5.0-8.5 American Association of Textile Chemist and Colorists (AATCC)

AATCC TM81|pH of the Water-Extract from Wet Processed Textiles|3363|

Bursting Strength lbs|Pounds Minimum 40 ASTM International ASTM D3787|Standard Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test|3363|

Alternately, ASTM D6797 may be used. The test method used is at the discretion of the vendor and should be specified in all reporting of the results.

Moisture regain - Calculation

Commercial %|Percentage Maximum 5 ASTM International ASTM D1909|Standard Tables of Commercial Moisture Regains and Commercial Allowances for Textile Fibers|3363|

21 Moisture regain - Calculation

Department of Defense - Internal ITP1|Moisture Regain Calculation |3363|

Toxicity The finished cloth shall not present a health hazard and shall show compatibility with prolonged, direct skin contact, as specified in 40 CFR §798.2250, Dermal Toxicity, and 40 CFR §798.4100, Dermal Sensitization. Chemicals recognized by the Environmental Protection Agency as human carcinogens shall not be used.

Department of Defense - Internal ITP6|Toxicity|3363|

9/4/2025 Page 7 of 15

Material Properties Color

Color Characteristic Characteristic and Additional Details UOM Min/Max Requirements Source Test method Test Method Options

Colorfastness - Crocking dry Minimum 4 American Association of Textile

Chemist and Colorists (AATCC) AATCC TM8|Colorfastness to Crocking:

Crockmeter|3363|

AATCC EP8 Evaluation Procedure for AATCC 9-Step Chromatic Transference Scale

Colorfastness - Crocking wet Minimum 4 American Association of Textile

Chemist and Colorists (AATCC) AATCC TM8|Colorfastness to Crocking:

Crockmeter|3363|

AATCC EP8 Evaluation Procedure for AATCC 9-Step Chromatic Transference Scale

3 Colorfastness - Light After 40 AFU or 170 kJ/(m2nm) at 420 nm

Minimum 4 American Association of Textile Chemist and Colorists (AATCC)

AATCC TM16.3|Colorfastness to Light:

Xenon-Arc|3363|

AATCC EP1 Evaluation Procedure for Gray Scale for Color Change.

Visual Shade Matching Daylight D65 AMS-STD-595/20150 American Association of Textile

Chemist and Colorists (AATCC) AATCC EP9|Evaluation Procedure for Visual Assessment of Color Difference of Textile|3363| option C

Visual Shade Matching Incandescent A AMS-STD-595/20150 American Association of Textile

Chemist and Colorists (AATCC) AATCC EP9|Evaluation Procedure for Visual Assessment of Color Difference of Textile|3363| option C

Colorfastness - Laundering 3 cycles Minimum 4 American Association of Textile Chemist and Colorists (AATCC)

AATCC TM61|Colorfastness to Laundering: Accelerated|3363|

AATCC EP1 Evaluation Procedure for Gray Scale for Color Change. AATCC EP2 Evaluation Procedure for Gray Scale for Staining.

Additional Material Properties and Testing

Characteristic Characteristic Additional Detail

Unit Of Measure Min/Max Requirements Source Test method Test Method Options

1 Construction Open-hole, net like warp knit mesh construction visual

9/4/2025 Page 8 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Internal Test Procedures

Material Internal Test Procedures Source Test Method Test method options Test method description

Department of Defense - Internal

ITP2|Hole Size Determination|3363| The hole size is determined by measuring the hole void in both the course and wale directions and taking the average of the course and wale void dimensions. A minimum of ten voids shall be measured in each direction. The cloth should be laid flat and be under no tension when measuring hole void.

Department of Defense - Internal

samples and blotting paper should be conditioned at 65±2 percent relative humidity (RH) and 70±2 °F for a minimum of 4 hours. Three 2- by 2-inch test specimens shall be tested per sample. Drying time test procedure. The following

between two pieces of unused blotting paper. Pass the sandwich through the wringer with a dead weight load of 27.7±0.5 kilograms. f. Immediately place specimen on the balance with top door of the balance open, side doors closed and record wet weight either to the nearest 0.01 or 0.10 gram. (The degree of dryness shall be determined by the user.) Manually monitor weight at set intervals until dry or use an automated balance with capability to weigh

Department of Defense - Internal

ITP5|Labile Sulfur|3363| Two (2) 1.50 (± 0.01) gram samples from each sample unit shall be tested. Each of the two (2) samples shall be cut into very small pieces and placed into separate test tubes. Prepare an acidic tin(II) chloride (stannous chloride) solution by dissolving 100 g SnCl2 (ACS grade) in 100 mL of 35% hydrochloric acid (ACS grade) and adding the mixture to 50 mL of distilled water. Prepare a lead acetate solution by dissolving 5.0 g of lead acetate (CP reagent grade) in a small amount of distilled water and diluting to a total of 100 mL. If the solution is not clear, add a few drops (one at a time) of glacial acetic acid until the solution is clear. The samples shall be submersed the acidic tin(II) chloride solution. A filter paper wet out with the lead acetate solution shall be placed over the top of the test tube.

The test tube containing the textile sample, tin(II) chloride and wet filter paper shall be heated over a low flame until the solution is boiling. The solution should not be heated for more than 15 seconds. A brown to black stain on the filter paper should be evaluated as follows: Free - The filter paper shows no discoloration or staining of any kind. Slight - The filter paper shows a light tan to light brown discoloration stain. Moderate - The filter paper shows a dark brown discoloration stain. Severe - The filter paper shows a black color stain. The rating shall be recorded. The results shall be recorded as “pass” or “fail. **

Department of Defense - Internal

ITP1|Moisture Regain Calculation |3363| The commercial moisture regain (CMR) values from ASTM D1909 shall be used for the fibers used in the yarn blend to calculate the moisture regain with the following formula: CMR of Fiber #1×Fiber #1 blend percentage CMR of Fiber #2×Fiber #2 blend percentage + CMR of Fiber #3×Fiber #3 blend percentage Total commercial moisture regain (CMR) Example: 78/22 modacrylic/rayon fabric 0.4%×78% modacrylic+11%×22% rayon=2.7% commercial moisture regain Where 0.4% is the CMR value for modacrylic fiber (class 1) and 11% is the CMR value for rayon

Department of Defense - Internal

ITP6|Toxicity|3363| If dermal toxicity testing is required, it will be conducted in accordance with Title 40 of the Code of Federal Regulations, current editions and applicable sections, which are consistent with OECD tests: Skin Sensitization 406 and Dermal Irritation 404 (https://www.oecd-ilibrary.org/environment/oecd-guidelines-for-the-testing-of -chemicals-section-4-health-effects_20745788?page=1). Dermal sensitization:

https://www.law.cornell.edu/cfr/text/40/798.4100 Dermal toxicity:https://www.law.cornell.edu/cfr/text/40/798.2250

9/4/2025 Page 9 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Defects Material Fabric type Defect Type Defect Description Details Major Minor

1 Knit Type V - Knits Edge ravels when pulled outward. ¨ ¨

2 Knit Type V - Knits Skewing ¨ ¨

3 Knit Type V - Knits Broken or missing yarn, dropped stitch, run. ¨ ¨

4 Knit Type V - Knits Any spot, stain or streak more than 1-inch in combined directions. ¨ ¨

5 Knit Type V - Knits Any mend. ¨ ¨

6 Knit Type V - Knits Stretch (stitch tension) knitting tension too high or too loose, washboards. ¨ ¨

7 Knit Type V - Knits Coarse or fine yarns resulting in noticeable difference in appearance stiffness and thickness. ¨ ¨

8 Knit Type V - Knits Twist yarn. ¨ ¨

9 Knit Type V - Knits Kinks or untrimmed ends. ¨ ¨

10 Knit Type V - Knits Knots greater than Fabric Defect Replica Scale Level D. ¨ ¨

11 Knit Type V - Knits Slubs greater than Fabric Defect Replica Scale Level F. ¨ ¨

12 Knit Type V - Knits Width not as specified within a tolerance of not less than 1/2-inch. ¨ ¨

13 Knit Type V - Knits Color not a good match to reference, barre. ¨ ¨

Knit Type V - Knits Any area of poor dye penetration, streak or shade bar that is

9-inches or less. Defective shade areas that are greater than 9-inches constitute a failure.

15 Knit Type V - Knits Objectionable odor. ¨ ¨

Defects

General Statements- Defects Category Description Detail Statement

1 Quality Material General Statement General Statement The finished material shall be examined and scored for the defects listed.

9/4/2025 Page 10 of 15

Defects Material Fabric type Defect Type Defect Description Details Major Minor

16 Knit Type V - Knits Slack or tight selvages (when applicable). ¨ ¨

17 Knit Type V - Knits Any embedded foreign matter or uncleanness. ¨ ¨

18 Knit Type V - Knits Edges rolled folded, creases, scalloped or cockled, baggy, ridgy or wavy knit. ¨ ¨

Additional defects Part NOS Defect Major Minor

1 01 Any cut, tear, abrasion mark, snag ¨ ¨

2 02 ¨ ¨

9/4/2025 Page 11 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Additional Packaging Details No Description

1 01

Packaging

General Statements- Packaging Category Description Detail Statement

1 Length and put-up Material General Statement General Statement For Government procurements only, unless otherwise specified in the contract, the cloth shall be furnished in continuous lengths, each not less than 50 yards, and each length shall be put-up on a roll

2 Roll Identification - Face Material General Statement General Statement he face side of the cloth shall be identified by stamping the face side with the word “FACE” at each end of the roll.

3 Roll Identification - Fiber Material General Statement General Statement Each roll shall be labeled or ticketed for fiber content in accordance with Title 16 CFR 303

4 Width Material General Statement General Statement For Government procurements only, unless otherwise specified, the width of the finished cloth shall be as specified and shall be the minimum acceptable width exclusive of the selvage

5 General Statement - Packaging

General Preservation, packing and marking shall be as specified in the contract.

9/4/2025 Page 12 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Additional General Statements Category Description Detail Statement

General Statements

General Statements Category Description Detail Statement

1 Distribution Statement A DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.

Comments, Suggestions or Questions

Defense Logistics Agency (DLA) Troop Support Comments, suggestions, or questions on this document should be addressed: 700 Robbins Street, Philadelphia, PA 19111-5096. Since contact information canchange, verify the currency of the address information using Acquisition Streamlining andStandardization Information System (ASSIST) online database https://assist.dla.mil.

3 Non Government Publications

American Association of Textile Chemist and Colorists

(AATCC)

Document Source Copies of these documents are available online at https://aatcc.org

4 Non Government Publications

American Society for Quality (ASQ) Document Source Copies of this document are available online at https://asq.org

5 Non Government Publications

ASTM International Document Source Copies of these documents are available online at http://www.astm.org.

Order of Precedence General Statement Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

Other Government documents, drawings and publications

Code of Federal Regulations (CFR) Document Source Copies of these documents are available online at https://www.ecfr.gov

Other Government documents, drawings and publications

Defense Logistics Agency (DLA) Troop Support Document Source Copies of this document are available online at https://www.dla.mil

Other Government documents, drawings and publications

General Statement The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those specified in the solicitation or contract.

9/4/2025 Page 13 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Additional Notes Grid Acquisition Requirement No Acquisition Type Acquisition Requirements

Notes Grid Acquisition Requirement No Acquisition Type Acquisition Requirements

1 01 Scope Title, number, and date of this specification

2 02 Quality Applicable Government patterns, drawings, standard samples, Embroidery , artwork and reference standards (including revisions)

3 03 Quality When first article is required

4 04 Quality When conformance inspection is required

5 05 Quality Length, width and put up required

6 06 Quality AQLs

7 07 Quality First article sampling and acceptance criteria, including sample size and sample unit

8 08 Quality Conformance inspection criteria

9 09 Quality Materials and components sampling and acceptance criteria

10 10 Quality Visual inspections conditions

11 11 Quality Materials and components examinations and tests

12 12 Quality Toxicity requirements and testing

13 13 Quality Shade Examination

14 14 Packaging Packaging requirements, additional

Notes and Concluding Material

General Statements - Notes Category Description Detail Statement

9/4/2025 Page 14 of 15

Description Cloth, Mesh Knit

MIL/CID Number MIL-DTL-32737

Fabric Status

Print/Solid Solid

Fabric Type Knit

Defect Type Type V - Knits

Year 2023

Enterprise DoD | 01

Service AR | Army

Category RM | Raw Material

Sub Category Material |

Size Range zRM - Rolled Goods |

Item Details Intended End Use ARTC Base layer 0

Keyword listing Baselayer, Drawers, ECW, Extreme cold weather, Marine Corps, MCWBL, No drip, No melt, Thermal, Underlayer, Undershirt

Comments

NSN

Size

Additional Notes

Concluding Material Project Number 8305-2022-035

Preparing Activity Navy - MC

Review Activities Review Activities

1 Army - AV

2 Army - CR

3 Army - IH

4 Army - MI

5 Navy - AS

Civilian Agencies Civilian Agencies

Custodian Custodian

1 Navy - MC

2 Air Force - 11

3 Army - GL

Known Sources Others Other Component Vendor Comments

Known Sources Material Product Code Vendor Material Name Comments

1 Hornwood | HWD | 766 Haileys Ferry Road, Lilesville, NC 28091

9/4/2025 Page 15 of 15