DH - Duct Mounted Humidifier Cutsheet.pdf

DRISTEEM ULTRA-SORB MODEL MP SUBMITTAL • PAGE 1 OF 5REV. 0319

Ultra-sorb Model MP steam dispersion panel mechanical specifications

FIGURE 1-1: ULTRA-SORB MODEL MP DIMENSIONS

OM-7915_mp

Top view

Elevation view

Blank side view

Header

Connections side view

A

A’

B’

C D

B

F

E

G

H

J

All except with 4" NPT steam inlet

4" NPT

steam inlet

G

H

Note:

See Table page 2-1: Ultra-sorb MP dimensions

DRISTEEM ULTRA-SORB MODEL MP SUBMITTAL • PAGE 2 OF 5REV. 0319

Table 2-1:

Ultra-sorb Model MP dimensions

Dimension Inches (mm)

A Unit width 15" (380 mm) min, 147" (3735 mm) max, in ½" (13 mm) increments

A' Face width 12" (305 mm) min, 144" (3660 mm) max, in ½" (13 mm) increments

B Unit height* 19.375" (492 mm) min, 151.375" (3845 mm) max, in ½" (13 mm) increments

B' Face height 12" (305 mm) min, 144" (3660 mm) max, in ½" (13 mm) increments

C Frame depth 7.2" (183 mm) 2.3" (58 mm) for side drain port (H) when 4" coupling (DN100) steam inlet

D Frame enclosure 1.5" (38 mm)

E Header enclosure 5.85" (149 mm)

F Mounting flange 1.5" (38 mm)

G �Humidification steam inlet

H �Drain port (internal thread) ¾" NPT (DN20) coupling

J Overall width

* �Panels with unit height more than 120" (3048 mm) have two-piece side flanges and are shipped with brackets for easy field assembly. Panels with unit height more than 98" (2490 mm) are shipped unassembled.

DRISTEEM ULTRA-SORB MODEL MP SUBMITTAL • PAGE 3 OF 5REV. 0319

Ultra-sorb Model MP connections, capacities, and dispersion tube detail

Table 3-2:

Ultra-sorb Model MP tube capacity*

Tubes lbs/hr kg/hr

1.5" Uninsulated 40 18.1

Insulated 43 19.5

2.0" Uninsulated 77 34.9

Insulated 80 36.3

* If face height (B') is <17" (432 mm), consult DriSteem or see DriCalc for the correct calculation.

Table 3-1:

Ultra-sorb Model MP unit capacity Evaporative steam Pressurized steam (2-50 psi) lbs/hr kg/hr lbs/hr kg/hr

700 318 2720 1235

OM-7841

Steam inlet location

Grommet

1½” (Typ)

¾” Offset (Typ)

1½ or 2" Dia.

dispersion tube

OM-7842

Orifice tubelet

Airflow

¾" (DN20) threaded condensate drain outlet

FIGURE 3-1: ULTRA-SORB MODEL MP STEAM INLET AND CONDENSATE

OUTLET POSITIONS

FIGURE 3-2: DISPERSION TUBE DETAIL

Steam supply header separator

Tubelets

Dispersion tubes

Dispersion tube insulation

OM-7843

Steam

FIGURE 3-4: INSULATED TUBE DETAIL

(HIGH-EFFICIENCY TUBE OPTION)

Grommet

DRISTEEM ULTRA-SORB MODEL MP SUBMITTAL • PAGE 4 OF 5REV. 0319

Ultra-sorb Model MP mounting - pressurized steam application

Notes:

1. Locate drain air gap only in spaces with adequate temperature and air movement to absorb flash steam; otherwise, condensation may form on nearby surfaces. Refer to governing codes for drain pipe size and maximum discharge water temperature.

2. Dashed lines indicate provided by installer.

3. Steam supply line to unit and piping are not included.

4. Mount the Ultra-sorb Model MP vertically (for horizontal airflow only).

5. For pressurized steam applications provide a 10" (255 mm) minimum water seal.

6. Locate drain air gap only in spaces with adequate temperature and air movement to absorb flash steam; otherwise, condensation may form on nearby surfaces. Refer to governing codes for drain pipe size and maximum discharge water temperature.

7. When mounting an Ultra-sorb in a duct, headers and flanges are mounted outside the duct.

8. 100% of the airflow must pass through the Ultra-sorb, which means that any openings surrounding it must be sealed. The blanked-off area below the Ultra-sorb provides clearance height for water seals, and condensate piping connections.

9. �Due to the pressure drop across the valve, the steam pressure at the header traps is minimal. Condensate must be drained.

10. Dispersion tubes are available at : 3" (76 mm), 4" (102 mm; for 2" diameter only), 6" (152 mm), 9" (228 mm), 12" (305 mm) centers.

11. �Ultra-sorb humidifiers will be assembled, crated, and shipped intact in all sizes up to 98" (2490 mm) tall. Ultra-sorb can be shipped unassembled, by request, requiring field assembly.

12. Sizes are 12" to 144" (305 mm to 3658 mm) x 12" to 144" (305 mm to 3658 mm) in 1" (25 mm) increments.

Each Ultra-sorb humidifier is furnished with:

1. Type 304 stainless steel header/separator and dispersion tubes when shipped unassembled.

2. Hardware for connection of dispersion tubes to header when shipped unassembled.

3. Tube grommets for connection when shipped unassembled.

Each Ultra-sorb humidifier used with boiler steam is also furnished with:

1. One 3/4" NPT float and thermostatic trap (≤15 psi steam source) or an inverted bucket trap for steam main drip leg use (>15 psi).

2. Inlet "Y" strainer.

3. Normally closed steam valve with stainless steel parabolic plug and seat.

Install strainer within 3' (1 m) of Ultra-sorb

Face width

Water seal (see Note 5)

Condensate header

1½" (38 mm) flange

AHU width

Face height

AHU/

Overall height

¾" (DN20) pipe thread

Valve

Open drain 1" (25 mm) air gap (see Note 1)

Tubelets perpendicular to airflow

OM-7839

FIGURE 4-1: MOUNTING ULTRA-SORB MODEL MP (PRESSURIZED STEAM APPLICATION SHOWN)

≥ 2" (51 mm)

Blanked-off area

DRISTEEM ULTRA-SORB MODEL MP SUBMITTAL • PAGE 5 OF 5REV. 0319

Ultra-sorb Model MP mounting - nonpressurized steam application

Water seal (see Note 4)

Typical evaporative humidifier

Depending on humidification load, interconnecting piping may be hose, tubing, or hard pipe

Face width

Blanked-off area

Position tubelets perpendicular to airflow

Insulate tubing and hard pipe to reduce steam loss

≥ 2" (51 mm)

1½" (38 mm) flange

AHU width

Face height AHU/Overall height

¾" (DN20) pipe thread

*Pitch 1/8"/ft (1%)

90˚ long sweep or two 45˚ elbows

Notes:

1. Locate drain air gap only in spaces with adequate temperature and air movement to absorb flash steam; otherwise, condensation may form on nearby surfaces. Refer to governing codes for drain pipe size and maximum discharge water temperature.

2. When mounting an Ultra-sorb in a duct, headers and flanges are mounted outside the duct.

3. Mount the Ultra-sorb Model MP vertically (for horizontal airflow only).

4. For non-pressurized steam, provide a 5" (127 mm) minimum water seal with a 2" (51 mm) minimum drop from the header connection.

5. 100% of the airflow must pass through the Ultra-sorb, which means that any openings surrounding it must be sealed. The blanked-off area below the Ultra-sorb provides clearance height for water seals and condensate piping connections.

6. Condensate must be drained.

7. Dispersion tubes are available at: 3" (76 mm), 4" (102 mm; for 2" diameter only), 6" (152 mm), 9" (228 mm), 12" (305 mm) centers.

8. �Ultra-sorb humidifiers will be assembled, crated, and shipped intact in all sizes up to 98" (2490 mm) wide. Ultra-sorb can be shipped unassembled, by request, requiring field assembly.

9. Sizes are 12" to 144" (305 mm to 3658 mm) x 12" to 144" (305 mm to 3658 mm) in 1" (25 mm) increments.

Each Ultra-sorb humidifier is furnished with:

*For electrode type humidifiers pitch towards Ultra-sorb MP steam dispersion panel.

OM-7840

Open drain 1" (25 mm) air gap:

(see Note 1)

FIGURE 5-1: MOUNTING ULTRA-SORB MODEL MP (NONPRESSURIZED STEAM APPLICATION SHOWN)

Condensate header