08_25R1303_10 51 13_Amd0008.pdf

FY24 MCON P-614 JOINT CONSOLIDATED COMMUNICATIONS CENTER 1737021

JOINT REGION MARIANAS, ANDERSEN AIR FORCE BASE

SECTION 10 51 13

HIGH DENSITY POLYETHYLENE/SOLID PLASTIC LOCKERS

05/11

PART 1 GENERAL

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

U.S. GENERAL SERVICES ADMINISTRATION (GSA)

FS AA-L-00486 (Rev J) Lockers, Clothing, Steel

1.2 SUBMITTALS

Government approval is required for submittals with a "G" designation;

submittals not having a "G" designation are for Contractor Quality Control approval. Submittals with an "S" are for inclusion in the Sustainability eNotebook, in conformance to Section 01 33 29 SUSTAINABILITY REPORTING.

Submit the following in accordance with Section 01 33 00 SUBMITTAL

PROCEDURES:

SD-02 Shop Drawings

Types; G

Location; G

Installation

Numbering system

SD-03 Product Data

Material

Handles

Finish

Locker components

Assembly instructions

SD-04 Samples

Color chips; G

1.3 DELIVERY, HANDLING, AND STORAGE

Deliver lockers and associated materials in their original packages, containers, or bundles bearing the manufacturer's name and the name of the material. Protect from weather, soil, and damage during delivery, storage, and construction.

SECTION 10 51 13 Page 1

Amendment No. 0008 10 51 13 HIGH DENSITY POLYETHYLENE/SOLID PLASTIC LOCKERS, dated April 14, 2025

1.4 FIELD MEASUREMENTS

To ensure proper fits, make field measurements prior to the preparation of drawings and fabrication. Verify correct location

1.5 QUALITY ASSURANCE

1.5.1 Color Chips

Provide a minimum of three color chips, not less than 3 inches square, of each color indicated.

PART 2 PRODUCTS

2.1 TYPES

Locker must have the following type and size in the location and quantities indicated. Locker finish colors will be as scheduled.

2.1.1 Multi-Tier

Multi-tier lockers must be as follows:

Type DTW-2: Double-tier locker 12 inches wide, 18 inches deep, and 72 inches high, without base

2.2 MATERIAL

2.2.1 High Density Polyethylene / Solid Plastic HDPE Sheet

Locker doors and frames must be made from high impact, high density polyethylene (HDPE) formed under pressure into solid plastic components 1/2-inch thick with homogeneous natural color throughout. Sides, tops, bottoms, backs, and shelves must be made from HDPE formed under pressure into solid plastic components 3/8-inch thick with homogeneous color throughout. Components must have machined edges to accept assembly brackets. Outsides, insides, tops, bottoms, backs, dividers, and shelves must be all one color.

2.2.2 Finish

2.2.2.1 HDPE

Finish must be slightly textured from top, bottom, shelves and sidewalls to reduce marring.

2.2.2.2 Color

As indicated.

2.3 COMPONENTS

2.3.1 Built-In Locks

Built-in locks are not required.

SECTION 10 51 13 Page 2

2.3.2 Coat Hooks

Two prong, high impact plastic, mounted to bottom of shelf or divider.

One per door opening.

2.3.3 Door Handles

Provide aluminum handles with a chromium coating.

2.3.4 Doors

Provide high impact polyethylene doors and frames formed under high pressure into solid plastic components, 1/2 inch thick with homogeneous color throughout.

2.3.4.1 Hinges

Provide full height stainless steel piano hinge. Weld or bolt hinges to the door frame. Weld, bolt, or rivet hinges to the door.

2.3.4.2 Latching Mechanisms

Provide continuous latch made from high impact polyethylene plastic. The spring loaded latch must be securely fastened to the entire length of the door providing a quiet latching function.

2.3.5 Latch Strikes

Fabricate from high impact polyethylene plastic, except latch strike may be continuous from top to bottom and fabricated as part of the door framing.

2.3.6 Back and Side Panels, Tops, and Bottoms

Provide end panels and filler panels of plastic material in same color as plastic locker.

2.3.7 Sloping Locker Tops

Provide sloping locker tops in addition to the locker-section flat tops.

Sloping tops must be continuous in length. Provide fillers or closures at the exposed end of sloping tops. Fabricate sloping tops from not less than 3/8 thick high impact polyethylene plastic.

2.3.8 Shelves

Fabricate from high impact polyethylene plastic.

2.3.9 Legs

Provide lockers without legs, as indicated.

2.3.10 Number Plates

FS AA-L-00486 . Aluminum. Provide consecutive numbers.

2.3.11 Fastening Devices

Provide bolts, nuts, and rivets as recommended by the locker manufacturer.

SECTION 10 51 13 Page 3

PART 3 EXECUTION

3.1 ASSEMBLY AND INSTALLATION

Assemble lockers according to the locker manufacturer's instructions.

Align lockers as indicated. Secure lockers to wall and base with screws as indicated. Bolt adjacent lockers together. Adjust doors to operate freely without sticking or binding and to ensure they close tightly.

3.2 NUMBERING SYSTEM

Install number plates on lockers consecutively.

3.3 FIELD QUALITY CONTROL

3.3.1 Repairing

Remove and replace damaged and unacceptable portions of completed work with new.

3.3.2 Cleaning

Clean surfaces of the work, and adjacent surfaces soiled as a result of the work, in an approved manner. Remove equipment, surplus materials, and rubbish from the site.

-- End of Section --

SECTION 10 51 13 Page 4