07_25R1303_10 28 13_Amd0008.pdf

FY24 MCON P-614 JOINT CONSOLIDATED COMMUNICATIONS CENTER 1737021

JOINT REGION MARIANAS, ANDERSEN AIR FORCE BASE

SECTION 10 28 13

TOILET ACCESSORIES

08/20

PART 1 GENERAL

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

U.S. DEPARTMENT OF DEFENSE (DOD)

MIL-STD-1691 (1994; Rev F) Construction and Material Schedule for Military Medical and Dental Facilities

1.2 SUBMITTALS

Government approval is required for submittals with a "G" or "S" classification. Submittals not having a "G" or "S" classification are for Contractor Quality Control approval. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:

SD-02 Shop Drawings

Product Schedule; G

Submit product Schedule indicating types, quantities, sizes, and installation locations by room for each toilet accessory item required. Identify locations using room designations indicated on the drawings.

SD-03 Product Data

Recycled content for stainless steel toilet accessories; S

Item A5030 Bench, Stall, Shower, Built In; G

Item A5070 Dispenser, Liquid Soap, SS, Surface Mounted; G

Item A5083 Dispenser, Paper Towel/Waste Receptacle, SS, Semi- Recessed; G

Item A5090 Disposal, Sanitary Napkin, SS, Surface Mounted; G

Item A5109 Grab Bar, 1-1/4 inch Dia., SS, 2 Wall, W/C Accessible; G

Item A5110 Grab Bar, 1-1/4 inch Dia., SS, 2 Wall, Shower Use; G

Item A5135 Shelf, Utility W/ Mop/Broom Holders, SS, Surf Mntd; G

Item A5145 Hook, Garment, Double, SS, Surface Mounted; G

Item A5170 Rod, Shower Curtain, 1 inch Diameter, W/Curtain & Hooks; G

SECTION 10 28 13 Page 1

Amendment No. 0008 10 28 13 TOILET ACCESSORIES, dated April 14, 2025

Item A5200 Dispenser, Toilet Tissue, SS, 2-Roll, Surface Mntd; G

Dispenser, Toilet Seat Cover, SS, Surface Mntd; G

Dispenser, Toilet Tissue/Toilet Seat Cover, SS, Partition Mntd; G

Submit catalog numbers, literature, data sheets, construction details, profiles, anchoring and mounting requirements ,including cutouts in other work and substrate preparation, and other pertinent data for each toilet accessory item to evaluate function, materials, dimensions and appearance.

SD-10 Operation and Maintenance Data

Item A5030 Bench, Stall, Shower, Built In; G

Item A5070 Dispenser, Liquid Soap, SS, Surface Mounted; G

Item A5083 Dispenser, Paper Towel/Waste Receptacle, SS, Semi- Recessed; G

Item A5090 Disposal, Sanitary Napkin, SS, Surface Mounted; G

Item A5109 Grab Bar, 1-1/4 inch Dia., SS, 2 Wall, W/C Accessible; G

Item A5110 Grab Bar, 1-1/4 inch Dia., SS, 2 Wall, Shower Use; G

Item A5135 Shelf, Utility W/ Mop/Broom Holders, SS, Surf Mntd; G

Item A5145 Hook, Garment, Double, SS, Surface Mounted; G

Item A5170 Rod, Shower Curtain, 1 inch Diameter, W/Curtain & Hooks; G

Item A5200 Dispenser, Toilet Tissue, SS, 2-Roll, Surface Mntd; G

Dispenser, Toilet Seat Cover , SS, Surface Mntd; G

Dispenser, Toilet Tissue/Toilet Seat Cover, SS, Partition Mntd; G

Submit Data Package 1 for each toilet accessory item in accordance with Section 01 78 23 OPERATIONS AND MAINTENANCE DATA.

1.3 DELIVERY, STORAGE, AND HANDLING

Wrap toilet accessories for shipment and storage, then deliver to the jobsite in manufacturer's original packaging, and store in a clean, dry area protected from construction damage and vandalism.

1.4 WARRANTY

Provide manufacturer's warranty to repair or replace defective materials and workmanship for a period of one year from date of final acceptance of the work.

SECTION 10 28 13 Page 2

PART 2 PRODUCTS

2.1 ACCESSORY ITEMS

Provide toilet accessories where indicated in accordance with Contractor-provided product schedule. Conform to the requirements for accessory items specified herein which are based on MIL-STD-1691 Joint Schedule Numbers (JSN). Porcelain type, tile-wall accessories are specified in Section 09 30 10 CERAMIC, QUARRY, AND GLASS TILING. Provide each accessory item complete with the necessary mounting plates of sturdy construction with corrosion resistant surface.

Provide stainless steel products listed herein manufactured from materials containing a minimum of 50 percent recycled content. Provide data identifying percentage of recycled content for stainless steel toilet accessories.

2.1.1 Anchors and Fasteners

Provide corrosion-resistant anchors and fasteners capable of developing a restraining force commensurate with the strength of the accessory to be mounted and suited for use with the supporting construction. Provide tamperproof design exposed fasteners with finish to match the accessory.

Provide fasteners proposed for use for each type of wall construction and mounting.

2.1.2 Finishes

Except where noted otherwise, provide the following finishes on metal:

Metal Finish

Stainless steel No. 4 satin finish

Carbon steel, copper alloy, and brass Chromium plated, bright

2.1.3 Item A5030 Bench, Stall, Shower, Built-In

Wall mounted shower seat. Frame made of 18 gauge stainless steel with satin finish. Seat made of one piece of 1/2 inch thick nonporous solid phenolic with slots to permit water to drain, secured to frame with stainless steel carriage bolts and acorn nuts. Mounting hardware included. Seat to support a minimum static load of 250 pounds. Hinge seat to fold up when not in use. Seat complies with ADA guidelines.

Approximate size: 34 inches wide by 22 inches deep by 1/2 inch thick.

2.1.4 Item A5070 Dispenser, Liquid Soap, SS, Surface Mounted

Surface mounted, top filling, liquid soap dispenser. Dispenser made of stainless steel with satin finish. Dispenser features corrosion-resistant valve, push-in type and operable with one hand; heavy duty hinge and key lock lid and vandal resistant concealed mounting. Minimum capactiy 40 fluid ounces.

SECTION 10 28 13 Page 3

2.1.5 Item A5083 Dispenser, Paper Towel/Waste Receptacle, SS, Semi-Recessed

Semi-Recessed convertible paper towel dispenser and waste receptacle with flange drawn and beveled, one-piece, seamless construction. Unit constructed of heavy gauge stainless steel with satin finish, all welded construction, have full length piano hinge and tumbler lock. Unit dispenses 600 C-fold or 800 multifold paper towels. Towel dispensing slot is snag-free. Removable waste receptacle is secured to cabinet with tumbler lock, have front and side edges of bottom and all top edges hemmed for safe handling, and minimum capacity of 12 gallons. Unit is ADA compliant.

2.1.6 Item A5090 Disposal, Sanitary Napkin, SS, Surface Mounted

Surface mounted sanitary napkin disposal. Unit made of stainless steel with satin finish and all welded construction. Unit has piano hinge attached at the top and an integral finger depression for opening. For use with disposable paper liners, available separately. Unit may be attached to wall or toilet partition.

Approximate size: 7 inches wide by 4 inches deep by 10 inches high.

2.1.7 Item A5109 Grab Bar, 1-1/4 Inch Diameter, SS, 2 Wall, W/C Accessible

Grab bar of 1-1/4 inch diameter satin finish stainless steel with peened gripping surface for use in toilet stall/room. Snap-on flange covers for concealed mounting are stainless steel and equipped with two screw holes for attachment to wall. Grab bars designed to meet and exceed ADA requirements for structural strength. Grab bars designed to withstand loads of 900 pounds when properly installed. Clearance from wall to grab bar is 1-1/2 inches to meet ADA and ANSI codes.

2.1.8 Item A5110 Grab Bar, 1-1/4 Inch Diameter, SS, 2 Wall, Shower Use

Grab bar of 1-1/4 inch diameter satin finish stainless steel with peened gripping surface. Snap-on flange covers for concealed mounting stainless steel. Bent ends of tubing pass through the flanges and are Heliarc welded for maximum strength. Grab bars designed to meet and exceed ADA requirements for structural strength. Grab bars designed to withstand loads of 900 pounds when properly installed. Clearance from wall to grab bar is 1-1/2 inches to meet ADA and ANSI codes.

2.1.9 Item A5135 Shelf, Utility W/ Mop/Broom Holders, SS, Surf Mounted

Surface mounted mop/broom holder with shelf made of 18 gauge stainless steel with all exposed surfaces in satin finish. Unit has shelf 8 inches deep with shelf support brackets of satin finish stainless steel welded to mounting base, and a minimum of 3 hooks/3 holders. Mop holders have spring-loaded rubber cams and hold mop or broom handle with a diameter between 5/8 inch and 1 inch.

Approximate size: 36 inches wide by 8 inches deep.

2.1.10 Item A5145 Hook, Garment, Double, SS, Surface Mounted

Surface mounted double garment hook made of stainless steel with satin finish. For use on door back or wall. Hook comes with concealed mounting bracket secured to concealed wall plate. Mounting hardware included.

Flange size is approximately 2 inches by 2 inches.

SECTION 10 28 13 Page 4

2.1.11 Item A5170 Rod, Shower Curtain, 1 Inch Diameter, W/Curtain & Hooks

Shower Curtain Rod with concealed mounting. Shower curtain rod made of satin finish stainless steel, 1 inch diameter, with flanges included.

Length as indicated on drawings.

2.1.12 Item A5200 Dispenser, Toilet Tissue, SS, 2-Roll, Surface Mounted

Concealed surface mounted, double roll, toilet tissue dispenser of stainless steel. Unit holds and dispenses two standard 5-1/4 inch diameter rolls of toilet tissue. Spindles are free-spinning for non-controlled delivery, chrome-plated plastic equipped with heavy-duty internal springs.

Approximate size: 7 inches diameter by 4 inches deep.

2.2 Dispenser, Toilet Seat Cover, SS, Surface Mntd (TSCD)

Type 304 stainless steel with surface mounted toilet seat cover dispensers. Dispenser must have a minimum capacity of 250 seat covers.

Toilet seat cover dispenser must protrude 4 inches maximum from face of finished wall.

2.3 Dispenser, Toilet Tissue/Toilet Seat Cover, SS, Partition Mntd

Partition mounted toilet seat cover dispenser / double roll toilet tissue dispenser of satin finish stainless steel. Unit holds and dispenses two standard 5-1/4 inch diameter rolls of toilet tissue. Spindles are free-spinning for non-controlled delivery, chrome-plated plastic equipped with heavy-duty internal springs. Unit must mount in partition and serve two toilet compartments where indicated. Flanges must be drawn and beveled, one-piece seamless construction. Door must be one-piece, seamless construction; secured to cabinet with full-length stainless steel piano hinge; and equipped with two tumbler keyed locks. Provide with sanitary napkin disposals for Women's Restrooms. Toilet seat cover dispenser and sanitary napkin disposal must be serviced from one side only. Toilet seat cover dispenser must be equipped with plastic sight barrier panel and can hold a maximum of 1000 seat covers. Sanitary napkin disposal must be secured to cabinet with spring-loaded, full-length stainless steel piano hinges, have hemmed edges and equipped with international graphic symbol identifying napkin disposal. Sanitary napkin disposal must be furnished with a removable, leak-proof, molded polyethylene receptacle with 0.8 gallon minimum capacity.

PART 3 EXECUTION

3.1 INSTALLATION

Do not install items that show visual evidence of biological growth.

Provide the same finish for the surfaces of fastening devices exposed after installation as the attached accessory. Provide oval exposed screw heads. Install accessories at the location and height indicated. Protect exposed surfaces of accessories with strippable plastic or by other means until the installation is accepted. After acceptance of accessories, remove and dispose of strippable plastic protection. Coordinate accessory manufacturer's mounting details with other trades as their work progresses. Use sealants for brackets, plates, anchoring devices and similar items in showers (a silicone sealantsealant specified in Section

SECTION 10 28 13 Page 5

07 92 00 JOINT SEALANTS) as they are set to provide a watertight installation. After installation, thoroughly clean exposed surfaces and restore damaged work to its original condition or replace with new work.

3.1.1 Semi-Recessed Accessories

Set anchors in mortar in masonry construction. Fasten to metal studs or framing with sheet metal screws in metal construction.

3.1.2 Surface Mounted Accessories

Mount on concealed backplates, unless specified otherwise. Conceal fasteners on accessories without backplates. Install accessories with corrosion-resistant fasteners as required by the construction. Install backplates in the same manner, or provide with lugs or anchors set in mortar, as required by the construction. Fasten accessories mounted on gypsum board and plaster walls without solid backing into the metal or wood studs, or to backplates secured to metal studs.

3.2 CLEANING

Clean material in accordance with manufacturer's recommendations. Do not use alkaline or abrasive agents. Take precautions to avoid scratching or marring exposed surfaces.

-- End of Section --

SECTION 10 28 13 Page 6

3.2 CLEANING