J-1800000-02.1 Bahrain_Final_Governing_Standards_March_2012.pdf

KINGDOM OF BAHRAIN

FINAL GOVERNING STANDARDS

13 March 2012

Prepared by

U.S. Navy Central Command

United States Central Command

On behalf of

United States Central Command (USCENTCOM)

This page intentionally left blank.

Kingdom of Bahrain Final Governing Standards

4 METHODOLOGY

METHODOLOGY

Chapters 2-19 of the FGS include scope, definitions and criteria. Appendices and tables are also presented. The applicable Kingdom of Bahrain environmental regulations were compared to the

May 2007 Overseas Environmental Baseline Guidance Document (OEBGD), and determinations were made as to whether an environmental regulation of the Kingdom of Bahrain was more or less stringent, equivalent to, or in addition to, the OEBGD standard. The more restrictive and additional standards were adopted in this FGS.

5 TABLE OF CONTENTS

TABLE OF CONTENTS

Section Page

FORWARD 3

METHODOLOGY 4

TABLE OF CONTENTS 5

REFERENCES 11

1. CHAPTER 1 OVERVIEW 12

1.1. PURPOSE 12

1.2. APPLICABILITY 12

1.3. EXEMPTIONS 12

1.4. DEFINITIONS 13

1.5. ADDITIONAL INFORMATION 13

1.6. WAIVERS 14

1.7. APPROVALS 14

1.8. WORKING WITH THE LEC 15

1.9. ACCESS TO INSTALLATIONS BY BAHRAIN AUTHORITIES 15

1.10. LEAD ENVIRONMENTAL COMPONENT 16

2. CHAPTER 2 AIR EMISSIONS 17

2.1. SCOPE 17

2.2. DEFINITIONS 17

2.3. CRITERIA 19

3. CHAPTER 3 DRINKING WATER 33

3.1. SCOPE 33

3.2. DEFINITIONS 33

3.3. CRITERIA 35

4. CHAPTER 4 WASTEWATER 63

4.1. SCOPE 63

4.2. DEFINITIONS 63

4.3. CRITERIA 66

5. CHAPTER 5 HAZARDOUS MATERIAL 77

5.1. SCOPE 77

5.2. DEFINITION 77

5.3. CRITERIA 78

6. CHAPTER 6 HAZARDOUS WASTE 84

6.1. SCOPE 84

6.2. DEFINITIONS 84

6.3. CRITERIA 86

7. CHAPTER 7 SOLID WASTE 125

7.1. SCOPE 125

7.2. DEFINITIONS 125

7.3. CRITERIA 128

8. CHAPTER 8 MEDICAL WASTE MANAGEMENT 133

8.1. SCOPE 133

8.2. DEFINITIONS 133

8.3. CRITERIA 134

9. CHAPTER 9 PETROLEUM, OIL, AND LUBRICANTS 141

9.1. SCOPE 141

9.2. DEIFINITIONS 141

9.3. CRITERIA 142

10. CHAPTER 10 PESTICIDES 147

10.1. SCOPE 147

10.2. DEFINITIONS 147

10.3. CRITERIA 148

11. CHAPTER 11 HISTORIC AND CULTURAL RESOURCES 151

11.1. SCOPE 151

11.2. DEFINITIONS 151

11.3. CRITERIA 153

12. CHAPTER 12 NATURAL RESOURCES AND ENDANGERED SPECIES 155

12.1. SCOPE 155

12.2. DEFINITIONS 155

12.3. CRITERIA 156

13. CHAPTER 13 POLYCHLORINATED BIPHENYLS 160

13.1. SCOPE 160

13.2. DEFINITIONS 160

13.3. CRITERIA 162

14. CHAPTER 14 ASBESTOS 170

14.1. SCOPE 170

14.2. DEFINITIONS 170

14.3. CRITERIA 171

15. CHAPTER 15 LEAD-BASED PAINT 173

15.1. SCOPE 173

15.2. DEFINITIONS 173

15.3. CRITERIA 176

16. CHAPTER 16 SPILL PREVENTION AND RESPONSE PLANNING 178

16.1. SCOPE 178

16.2. DEFINITIONS 178

16.3. CRITERIA 180

17. CHAPTER 17 UNDERGROUND STORAGE TANKS 185

17.1. SCOPE 185

17.2. DEFINITIONS 185

17.3. CRITERIA 186

APPENDICES

AP1. APPENDIX 1 – CHARACTERISTICS OF HAZARDOUS WASTES AND LISTS OF

HAZARDOUS WASTES AND HAZARDOUS MATERIALS 189

AP2. APPENDIX 2 – DETERMINATION OF WORST CASE DISCHARGE PLANNING

VOLUME 254

TABLES

Table 2. 1. Emission Standards for Fuel Combustion Sources 26

Table 2. 2. Controlled ODS in Bahrain 27

Table 2. 3. Additional Ozone Depleting Substances Controlled on DoD Installations 28

Table 2. 4. Emission Standards for Incinerators 29

Table 2. 5. Carbon Monoxide Operating Limits for Incinerators 30

Table 2. 6. Air Emission Standards for Medical Waste Incinerators with >1 Ton per Hour 31

Table 2. 7. Air Emission Standards for Medical Waste Incinerators with< 1 Ton per Hour 32

Table 2. 8. Dioxins and Furans 32

Table 3. 1. Surface Water Treatment Requirements 43

Table 3. 2. Total Coliform Monitoring Frequency 45

Table 3. 3. Inorganic Chemical MCLs 46

Table 3. 4. Inorganics Monitoring Requirements 47

Table 3. 5. Recommended Fluoride Concentrations at Different Temperatures 48

Table 3. 6. Monitoring Requirements for Lead and Copper Water Quality Parameters 48

Table 3. 7. Synthetic Organic Chemical MCLs 49

Table 3. 8. Synthetic Organic Chemical Monitoring Requirements 50

Table 3. 9. Disinfectant/Disinfection Byproducts Monitoring Requirements 51

Table 3. 10. Radionuclide MCLs and Monitoring Requirements 54

Table 3. 11. CT Values for Inactivation of Giardia Cysts by Free Chlorine at 0.5C or Lower* 55

Table 3. 12. CT Values for Inactivation of Giardia Cysts by Free Chlorine at 5.0°C* 56

Table 3. 13. CT Values for Inactivation of Giardia Cysts by Free Chlorine at 10C* 57

Table 3. 14. CT Values for Inactivation of Giardia Cysts by Free Chlorine at 15C* 58

Table 3. 15. CT Values for Inactivation of Giardia Cysts by Free Chlorine at 20C* 59

Table 3. 16. CT Values for Inactivation of Giardia Cysts by Free Chlorine at 25C* 60

Table 3. 17. CT Values for Inactivation of Viruses by Free Chlorine 61

Table 3. 18. CT Values for Inactivation of Giardia Cysts by Chlorine Dioxide 61

Table 3. 19. CT Values for Inactivation of Viruses by Free Chlorine Dioxide pH 6-9 61

Table 3. 20. CT Values for Inactivation of Giardia Cysts by Ozone 61

Table 3. 21. CT Values for Inactivation of Viruses by Free Ozone 61

Table 3. 22. CT Values for Inactivation of Giardia Cysts by Chloramine pH 6-9 62

Table 3. 23. CT Values for Inactivation of Viruses by Chloramine 62

Table 3. 24. CT Values for Inactivation of Viruses by UV 62

Table 4. 1. Monthly Average and Maximum Discharge Standards to Receiving Waters 72

Table 4. 2. Components of Total Toxic Organics 73

Table 4. 3. Monitoring Requirements 75

Table 4. 4. Best Management Practices 76

Table 5. 1. Typical Hazardous Materials Characteristics 83

Table 6.1. List of hazardous characteristics 105

Table 6.2. Controlled Waste Categories 106

Table 6.3. Wastes Characterized as Hazardous Metal and Metal-Bearing 108

Table 6.4. Wastes Containing Principally Inorganic Constituents, Which may Contain

Metals and Organic Materials 110

Table 6.5. Wastes Containing Principally Organic Constituents, Which may Contain

Metals and Inorganic Materials 110

Table 6.6. Wastes which may Contain Either Inorganic or Organic Constituents 112

Table 6.7. B1 Metal and Metal-Bearing Wastes 113

Table 6.8. B2 Wastes Containing Principally Inorganic Constituents, which may Contain

Metals and Organic Materials 116

Table 6.9. B3 Wastes Containing Principally Organic Constituents, which may Contain

Metals and Inorganic Materials 118

Table 6.10. B4 Wastes which may Contain Either Inorganic or Organic Constituents 121

Table 6.11. Resource Recovery, Recycling, Reclamation, Direct Re-use or Alternative Uses 122

Table 6.12. Generator Information Requirements for Competent Authority 123

Table 6.13. Information Requirements for Waste Disposal Outside Bahrain 124

Table 8. 1. Treatment and Disposal Methods for Infectious Medical Waste 140

Table 12. 1. Threatened and Endangered (T&E) Species 158

Table 12.2. List of Bahrain Protected Areas 159

Table AP1. T1. Maximum Concentration of Contaminants for the Toxicity Characteristic 194

Table AP1. T2. Maximum Concentration of Contaminants for Non-Wastewater 195

Table AP1. T3. Listed Hazardous Wastes from Non-Specific Sources 196

Table AP1. T4. List of Hazardous Waste/Substances/Materials 200

REFERENCES

Department of Defense

(a) DoD Instruction 4715.5, ―Management of Environmental Compliance at Overseas

Installations,‖ April 22, 1996

(b) Executive Order 12344, ―Naval Nuclear Propulsion Program,‖ February 1, 1982

(c) Section 7158 of title 42, United States Code

(d) Executive Order 12114, ―Environmental Effects Abroad of Major Federal Actions,‖

January 4, 1979

(e) DoD Instruction 4715.4, ―Pollution Prevention,‖ June 18, 1996

(f) DoD 8910.1-M, ―DoD Procedures for Management of Information Requirements,‖ June

30, 1998

(g) DoD Instruction 6050.05, ―DoD Hazard Communication (HAZCOM) Program,‖

August 15, 2006

(h) Defense Logistics Agency Instruction 4145.11, Army Technical Manual 38-410, Naval

Supply Publication 573, Air Force Joint Manual 23-209, and Marine Corps Order

4450.12A, ―Storage and Handling of Hazardous Materials,‖ January 13, 1999

(i) Air Force Interservice Manual 24-204(I), Army Technical Order 3 8-250, Naval Supply

Publication 505, Marine Corps Order P4030.19I, and Defense Logistics Agency

Instruction 4145.3, Defense Contract Management Agency D1, Ch3.4 (HM24), ―Preparing Hazardous Materials for Military Air Shipments,‖ 15 April 2007, Incorporating Change 1, 4 May 2007.

(j) DoD 4160.21 -M, ―Defense Materiel Disposition Manual,‖ August 18, 1997, authorized by DoD 4140.1-R, ―Department of Defense Materiel Management Regulation,‖

January 25, 1993

(k) DoD Directive 4001.1, ―Installation Management,‖ September 4, 1986

(l) Naval Facility Manual of Operation-213, Air Force Regulation 9 1-8, and Army

Technical Manual 5-634, ―Solid Waste Management,‖ May 1990

(m) DoD 4150.7-M, ―DoD Pest Management Training and Certification,‖ April 24, 1997

(n) Military Handbook 1 028/8A, ―Design of Pest Management Facilities,‖

November 1, 1991

(o) DoD Instruction 6055.1, ―DoD Safety and Occupational Health (SOH) Program,‖

August 19, 1998

(p) DoD Instruction 6055.5, ―Industrial Hygiene and Occupational Health,‖

January 10, 1989

(q) Section 2643 of title 15, United States Code

(r) Title 40, Code of Federal Regulations, Part 763, Subpart E, ―Asbestos-Containing

Materials in Schools,‖ current edition

(s) DoD Instruction 4715.8, ―Environmental Remediation for DoD Activities Overseas,‖

February 2, 1998

CHAPTER 1

OVERVIEW

1.1 PURPOSE.

The primary purpose of these Final Governing Standards (FGS) is to provide environmental compliance criteria at United States (U.S.) Department of Defense (DOD) installations in

Bahrain. This document implements DOD Instruction 4715.5, ―Management of Environmental

Compliance at Overseas Installations,‖ dated 22 April 1996, and is based upon DOD 4715.05-G, ―Overseas Environmental Baseline Guidance Document‖ (OEBGD), dated 1 May 2007.

1.2 APPLICABILITY.

1.2.1. These FGS provide environmental compliance criteria applicable to actions for

DOD Components at installations located in the Kingdom of Bahrain.

1.2.2. These FGS represent minimum criteria; DOD Components may impose additional criteria provided those policies and directives do not directly conflict with these FGS.

1.2.3. Activities and installations shall notify the Environmental Executive Agent

(EEA), United States Central Command (US

1.2.4. CENTCOM), via the Lead Environmental Component (LEC), Commander Navy

Region Europe Africa Southwest Asia (CNREURAFSWA), of any directly conflicting DOD

Component policies or directives they discover prior to imposing criteria more protective than provided in these FGS.

1.2.5. DOD Components shall not enter into agreements with Bahrain authorities at any level that establishes a criterion for environmental compliance that contradicts those provided in these FGS without the prior written approval of the LEC.

1.3. EXEMPTIONS.

These FGS do not apply to:

1.3.1. DOD installations that do not have more than de minimis potential to affect the natural environment (e.g., offices whose operations are primarily administrative, including defense attaché offices, security assistance offices, foreign buying offices, and other similar organizations), or for which the DOD Components exercise control only on a temporary or intermittent basis.

1.3.2. Leased, joint use, and similar facilities to the extent that the DOD does not control the instrumentality or operation that a criterion seeks to regulate.

1.3.3. Operations of U.S. military vessels or the operations of U.S. military aircraft, or off installation operational and training deployments. Off-installation operational deployments include cases of hostilities, contingency operations in hazardous areas, and when U.S. forces are operating as part of a multi-national force not under full control of the United States. Such excepted operations and deployments shall be conducted in accordance with applicable international agreements, other DOD Directives (DODDs) and DOD Instructions (DODIs), and environmental annexes incorporated into operation plans or operation orders. However, these

FGS do apply to support functions for U.S. military vessels and U.S. military aircraft provided by the DOD Components, including management or disposal of off-loaded waste or material.

1.3.4. Facilities and activities associated with the Naval Nuclear Propulsion Program, which are covered under Executive Order (E.O.) 12344 ―Naval Nuclear Propulsion Program,‖ and conducted pursuant to 42 United States Code (U.S.C.) 7158.

1.3.5. The determination or conduct of remediation to correct environmental problems caused by the Department of Defense's past activities, conducted in accordance with DOD

Instruction (DODI) 4715.8, ―Environmental Remediation for DOD Activities Overseas.

1.3.6. Environmental analyses conducted under E.O. 12114, ―Environmental Effects

Abroad of Major Federal Actions.‖

1.4. DEFINITIONS.

For purposes of these FGS, unless otherwise indicated, the following definitions apply:

1.4.1. Criteria and Management Practices. Particular substantive provisions of the

OEBGD that are used by the EEA to develop these FGS.

1.4.2. Existing Facility. Any facility and/or building, source, or project in use or under construction before 1 October 1994, unless it is subsequently substantially modified.

1.4.3. Final Governing Standards. A comprehensive set of country-specific substantive provisions, typically technical limitations on effluent, discharges, etc., or a specific management practice.

1.4.4. New Facility. Any facility and/or building, source, or projects with a construction start date on or after 1 October 1994, or a pre-existing facility that has been substantially modified since 1 October 1994.

1.4.5. Substantial Modification. Any modification to a facility and/or building the cost of which exceeds $1 million, regardless of funding source.

1.5. ADDITIONAL INFORMATION.

1.5.1. The DOD Components shall establish and implement an environmental audit program to ensure that overseas installations assess compliance with these FGS at least once every 3 years at all major installations.

1.5.2. DODI 4715.4, ―Pollution Prevention,‖ implements policy, assigns responsibility, and prescribes procedures for implementation of pollution prevention programs throughout the

DOD. As a matter of DOD policy, DODI 4715.4 should be consulted for particular requirements that apply to activities outside the United States. Pollution prevention should be considered in developing the criteria and management practices for these FGS. Where economically advantageous and consistent with mission requirements, pollution prevention shall be the preferred means for attaining compliance with these FGS.

1.5.3. Laboratory analyses necessary to implement these FGS would normally be conducted in a laboratory that has been certified by a U.S. or Bahrain regulatory authority for the applicable test method. In the absence of a certified laboratory, analyses may also be conducted at a laboratory that has an established reliable record of QA compliance with standards for the applicable test method that are generally recognized by appropriate industry or scientific organizations, such as ISO 17025.

1.5.4. These FGS do not create any rights or obligations enforceable against the United

States, the DOD, or any of its components, nor does it create any standard of care or practice for individuals. Although these FGS refers to other DODDs and DODIs, it is intended only to coordinate the requirements of those directives as required to implement the policies found in

DODI 4715.5. These FGS do not change other DOD or service directives or instructions, or alter

DOD or service policies.

1.6. WAIVERS.

1.6.1. If compliance with the FGS at particular installations or facilities would seriously impair operations, adversely affect relations with Bahrain authorities, or require substantial expenditure of funds at an installation that has been identified for closure or at an installation that has been identified for a realignment that would remove the requirement, a DOD Component may ask the EEA, via the LEC, to waive the particular standard. See DOD Instruction 4715.5, ―Management of Environmental Compliance at Overseas Installations‖, and USCENTCOM

Regulation 200-1, ―Protection and Enhancement of Environmental Assets,‖ for complete waiver procedures.

1.7. APPROVALS.

1.7.1. Approval may be required to engage in activities that have the potential to affect the environment in Bahrain. Generally, activities that occur within the confines of the installation and do not affect the environment outside of the installation do not require approval.

DoD Components shall not apply for approval directly from Bahrain authorities. DoD

Components shall contact the LEC to determine approval requirements and coordinate with

Bahrain representatives regarding activities that may require approval as indicated in these FGS.

If the installation has a Bahrain Installation Commander (BIC), the U.S. Installation Commander or designated representative shall inform the BIC of activities that may require approval, keeping the LEC informed. If the BIC declines to engage regarding an approval, DOD Components shall contact the LEC to determine approval requirements.

1.7.2. If Bahrain approval specifies a more protective standard than prescribed in the

FGS, the standard in the approval shall be the compliance standard. However, if an approval allows a less protective standard, then the FGS will be the compliance standard unless a waiver is obtained (see section 1.6).

1.7.3. Contractors performing work for DOD on DOD installations must comply with all

Bahrain laws and regulations including obtaining all necessary licenses and approvals.

Contracting services does not absolve DOD Components from compliance with these FGS unless exempted under section 1.3, Exemptions.

1.7.4. Certificates obtained from appropriate Bahrain authorities (e.g., tank tightness testing) do not fall within the definition of an approval process requiring the LEC. Request for services (e.g., inspections) shall be forwarded directly to the appropriate organizations without involving the LEC.

1.8. WORKING WITH THE LEC.

1.8.1. DOD Components shall consult with the LEC when specified in these FGS and when:

1.8.1.1. Significant exceedances of FGS or approval criteria occur

1.8.1.2. Bahrain enforcement action is initiated

1.8.1.3. An issue is raised that has the potential to affect multiple installations or military services

1.8.2. DOD Components shall notify the LEC when specified in these FGS and when:

1.8.2.1. Information is provided to BIC for activities requiring approval governed by these FGS.

1.8.2.2. BIC or other Bahrain official requests information.

1.8.2.3. Any Bahrain official requests access to an installation in order to conduct an environmental inspection.

1.8.3. The LEC, working with the notifying DOD Component, may determine that notification specified in these FGS is no longer required on a case-by-case basis.

1.9. ACCESS TO INSTALLATIONS BY BAHRAIN AUTHORITIES. Inspections and non-routine requests for information by Bahrain authorities shall be coordinated with the BIC (if designated for a facility) or the LEC and reported to the EEA via the Component chain-of-command. To the maximum extent possible, U.S. military personnel, rather than civilian personnel, shall lead the review of DOD Component activities by Bahrain authorities during the inspection.

1.10. LEAD ENVIRONMENTAL COMPONENT.

The LEC for these FGS is the Commander, Navy Region Europe Africa Southwest Asia.

Any questions or comments pertaining to these FGS shall be sent to:

Commander, Navy Region Europe Africa Southwest Asia

PSC 817 Box 108

FPO AE 09622

DSN Voice (314) 626-2886

DSN FAX (314) 626-4341

Commercial +39 081-568-2886

Or to the Environmental LEC representative in Bahrain at:

Commander Navy Region Europe Africa Southwest Asia

Detachment Bahrain

Environmental Program

PSC 451 BOX 850

FPO AE 09834-2800

DSN Voice (318) 439-4603

DSN FAX (318) 439-3028

Commercial +973-1-785-4603

CHAPTER 2

AIR EMISSIONS

2.1. SCOPE

This Chapter contains standards for air emissions sources. Criteria addressing open burning of solid waste are contained in Chapter 7, ―Solid Waste.‖ Criteria addressing asbestos are contained in Chapter 15, ―Asbestos.‖

2.2. DEFINITIONS

2.2.1. Coal Refuse. Waste products from coal mining, cleaning, and coal preparation operations (e.g., culm and gob) contain coal, matrix material, clay, and other organic and inorganic material.

2.2.2. Cold Cleaning Machine. Any device or piece of equipment that contains and/or uses liquid solvent, into which parts are placed to remove soil and other contaminants from the surfaces of the parts or to dry the parts. Cleaning machines that contain and use heated, non-boiling solvent to clean the parts are classified as cold cleaning machines.

2.2.3. Commercial and Industrial Solid Waste Incinerator (CISWI) Units. Any combustion device that combusts commercial and industrial waste in an enclosed device using controlled flame combustion without energy recovery that is a distinct operating unit of any commercial or industrial facility (including field-erected, modular, and custom incineration units operating with starved or excess air). CISWI units do NOT include Municipal Waste Combustor Units, Sewage

Sludge Incinerators, Medical Waste Incinerators, and Hazardous Waste Combustion Units.

2.2.4. Controlled Substances. Chemicals (in both mixed and pure form) listed in Table 2.2.

2.2.5. De minimis. This term means that average person would regard an issue to be so minor that it is insignificant.

2.2.5. Fossil Fuel. Natural gas, petroleum, coal, and any form of solid, liquid, or gaseous fuel derived from such material for the purpose of creating useful heat.

2.2.6. Freeboard Ratio. The ratio of the solvent cleaning machine freeboard height to the smaller interior dimension (length, width, or diameter) of the solvent cleaning machine.

2.2.7. Hanging Inhalable Particles. Naturally hanging particles resulting from sand storms, forest fires, and volcanic activities, in addition to some industrial activities. They are classified according to size. Those between 0.1µm and 10µm are classified as hanging inhalable particles.

2.2.8. Hydrofluorocarbon (HFC). A compound consisting of hydrogen, fluorine, and carbon often used as a replacement for Ozone-Depleting Substances (ODS).

C2.2.9. Incinerator. Any furnace used in the process of burning solid or liquid waste for the purpose of reducing the volume of the waste by removing combustible matter, including equipment with heat recovery systems for either hot water or steam generation.

2.2.10. Most Appropriate Available Technique. The best standards, criteria, levels, and means available to prevent or reduce pollution from projects in the country and are defined by a specialized authority.

2.2.11. Motor Vehicle. Any commercially available vehicle that is not adapted to military use that is self-propelled and designed for transporting persons or property on a street or highway, including but not limited to, passenger cars, light duty vehicles, and heavy duty vehicles.

2.2.12. Municipal Waste Combustion (MWC) Units. Any equipment that combusts solid, liquid, or gasified municipal solid waste (MSW) including, but not limited to, field-erected

MWC units (with or without heat recovery), modular MWC units (starved-air or excess-air), boilers (for example, steam generating units), furnaces (whether suspension-fired, grate-fired, mass-fired, air curtain incinerators, or fluidized bed-fired), and pyrolysis/combustion units.

Municipal waste combustion units do NOT include pyrolysis or MWC units located at a plastics or rubber recycling unit, cement kilns that combust MSW, internal combustion engines, gas turbines, or other combustion devices that combust landfill gases collected by landfill gas collection systems.

2.2.13. Municipal Solid Waste (MSW). Household, commercial/retail, or institutional waste. Household waste includes material discarded from residential dwellings, hotels, motels, and other similar permanent or temporary housing. Commercial/retail waste includes material discarded by stores, offices, restaurants, warehouses, non-manufacturing activities at industrial facilities, and other similar establishments or facilities. Institutional waste includes materials discarded by schools, hospitals (non-medical), non-manufacturing activities at prisons and government facilities, and other similar establishments or facilities. Household, commercial/retail, and institutional waste does include yard waste and refuse-derived fuel.

Household, commercial/retail, and institutional waste does not include used oil; sewage sludge;

wood pallets; construction, renovation, and demolition wastes (which include railroad ties and telephone poles); clean wood; industrial process or manufacturing wastes; medical waste; or motor vehicles (including motor vehicle parts or vehicle fluff).

2.2.14. Ozone-Depleting Substances. Those substances listed in Tables 2.2 and 2.3.

2.2.15. Pathological Waste. Waste material consisting of only human or animal remains, anatomical parts, and/or tissue, the bags/containers used to collect and transport the waste material, and animal bedding (if applicable).

2.2.16. Perfluorocarbon (PFC). A compound consisting solely of carbon and fluorine often used as a replacement for ODS.

2.2.17. Process Heater. A device that is primarily used to heat a material to initiate or promote a chemical reaction in which the material participates as a reactant or catalyst.

2.2.18. Pyrolysis. The endothermic gasification of hospital waste and/or medical/infectious waste using external energy.

2.2.19. Stack. Any point in a source covered by criteria contained in 2.3.1., 2.3.2., 2.3.3., 2.3.4., or 2.3.5. designed to emit pollutants.

2.2.20. Steam/Hot Water Generating Unit. A device that combusts any fuel and produces steam or heats water or any other heat transfer medium. This definition does not include nuclear steam generators or process heaters.

2.2.21. Substantially-Modified. Any modification to a facility/building, the cost of which exceeds 377,100 BD ($1 million), regardless of funding source.

2.2.22. Vapor Cleaning Machine. A batch or in-line solvent cleaning machine that boils liquid solvent which generates solvent vapor that is used as a part of the cleaning or drying cycle.

2.3. CRITERIA

2.3.1. Steam/Hot Water Generating Units. The following standards apply to units that commenced construction on or after 1 October 1994 or that were substantially modified since 1

October 1994.

2.3.1.1. Air Emission Standards. The following criteria apply to units with a maximum design heat input capacity ≥ 3.0 MW or 10 million Btu/hr.

2.3.1.1.1. Steam/hot water generating units and associated emissions controls, if applicable, must be designed to meet the emission standards for specific sized units shown in

Table 2.1. at all times.

2.3.1.1.2. For units combusting liquid or solid fossil fuels, fuel sulfur content (weight

%) and higher heating value will be measured and recorded for each new shipment of fuel.

Document compliance with the SO2 limits using the limits in Table 2.1. Alternatively, install a properly calibrated and maintained continuous emissions monitoring system to measure the flue gas for SO2 and either oxygen (O2) or carbon dioxide (CO2). Otherwise SO2 shall be measured using the fluorescent method, or any other internationally-approved method.

2.3.1.2. Air Emissions Monitoring. Steam/hot water generating units subject to opacity or nitrogen oxides (NOX) standards in Table 2.1, must have a properly calibrated and maintained continuous emissions monitoring system (CEMS) to measure the flue gas as follows:

2.3.1.2.1. For units with a maximum design heat input capacity > 9 MW (30 million

Btu/hr): Opacity, except that CEMS is not required where gaseous or distillate fuels are the only fuels combusted.

2.3.1.2.2. For fossil fuel fired units with a maximum design heat input capacity > 30

MW (100 million Btu/hr): NOX and either O2 or CO2.

2.3.2. Incinerators. The following requirements do not apply to incinerators combusting hazardous waste or munitions. Refer to Chapter 6, ―Hazardous Waste,‖ for information regarding hazardous waste disposal and incineration.

2.3.2.1. Commercial and Industrial Solid Waste Incinerators (CISWI). All CISWI units must comply with the applicable emission standards in Table 2.4. and operating limits in Table

2.5.

2.3.2.2. Municipal Waste Combustion (MWC) Units. Each MWC unit must comply with the applicable emission standards in Table 2.4. and operating limits in Table 2.5.

2.3.2.3. Sewage Sludge Incinerators. All sewage sludge incinerators that commenced construction on or after 1 October 1994 or that were substantially modified since 1 October 1994 and that burn more than 0.907 tons per day (tpd)) of sewage sludge or more than 10% sewage sludge, must also be designed to meet a particulate emission limit of 0.65 g/kg dry sludge (1.30 lb/ton dry sludge) and an opacity limit of 20% at all times, except during periods of startup, shut down, malfunction, or when emergency conditions exist.

2.3.2.4. Medical Waste Incinerators (MWI). The following standards apply to all units.

These requirements do not apply to any portable units (field deployable), pyrolysis units, or units that burn only pathological, low-level radioactive waste, or chemotherapeutic waste. Refer to

Chapter 8, ―Medical Waste Management,‖ for other requirements pertaining to medical waste management.

2.3.2.4.1. All MWI must be designed and operated according to the following good combustion practices (GCP):

2.3.2.4.1.1. Unit design: dual chamber.

2.3.2.4.1.2. Minimum temperature in primary chamber: 760-871°C (1400-

1600°F).

2.3.2.4.1.3. Minimum temperature in secondary chamber: 982-1204°C (1800-

2200°F).

2.3.2.4.1.4. Minimum residence time in the secondary chamber: 2 seconds.

2.3.2.4.1.5. Incinerator operators must be trained in accordance with applicable

Service requirements.

2.3.2.4.1.6. Medical waste incinerators shall operate within the emission standards listed on Tables 2.6, 2.7, and 2.8.

2.3.3. Perchloroethylene (PCE) Dry Cleaning Machines. The following requirements apply to all dry cleaning machines. Chemicals listed on Table 2.2 shall NOT be used in dry cleaning and vapor degreasing activities.

2.3.3.1. Emissions from PCE dry cleaning machines installed before 1 October 1994 that use more than 7,571 liters (2,000 gallons) per year of PCE (installation wide) in dry cleaning operations, must be controlled with a refrigerated condenser, unless a carbon absorber was already installed. The temperature of the refrigerated condenser must be maintained at 7.2°C

(45°F) or less. Dry cleaning machines and control devices must be operated according to manufacturer recommendations.

2.3.3.2. All PCE dry cleaning systems installed on or after 1 October 1994 must be of the dry-to-dry design with emissions controlled by a refrigerated condenser. The temperature of the refrigerated condenser must be maintained at 7.2°C (45°F) or less. Dry cleaning machines and control devices must be operated according to manufacturer recommendations.

2.3.4. Chromium Electroplating and Chromium Anodizing Tanks. Electroplating and anodizing tanks must comply with one of the three methods below for controlling chromium emissions. Implement one of the following methods that are most appropriate to suit local conditions:

2.3.4.1. Option 1: Limit chromium emissions in the ventilation exhaust to 0.015 milligrams per dry standard cubic meter (mg/dscm). Control devices/methods must be operated according to manufacturer recommendations.

2.3.4.2. Option 2: Use chemical tank additives to prevent surface tension of the electroplating or anodizing bath from exceeding 45 dynes per centimeter (cm) as measured by a stalagmometer or 35 dynes/cm as measured by a tensiometer. Measure the surface tension prior to the first initiation of electric current on a given day and every 4 hours thereafter.

2.3.4.3. Option 3: Limit chromium emissions to the maximum allowable mass emission rate (MAMER) calculated using the following equation: MAMER = ETSA x K x 0.015 mg/dscm, where: MAMER = the alternative emission rate for enclosed hard chromium electroplating tanks in mg/hr; ETSA = the hard chromium electroplating tank surface area in square feet (ft ); K = a conversion factor, 425 dscm/( ft

-hr). Option 3 is ONLY applicable to hard chrome electroplating tanks equipped with an enclosing hood and ventilated at half the rate or less than that of an open surface tank of the same surface area.

2.3.5. Halogenated Solvent Cleaning Machines. These requirements apply to all solvent cleaning machines that use solvent which contains > 5 % by weight: methylene chloride (CAS

No. 75-09-2), perchloroethylene (CAS No. 127-18-4), trichloroethylene (CAS No. 79-01-6), 1,1,1-trichloroethane (CAS No. 71-55-6), chloroform (CAS No. 67-66-3), or any combination of these halogenated solvents. The use of carbon tetrachloride (CAS No. 56-23-5) in any equipment or appliance is prohibited.

2.3.5.1. All cold cleaning machines (remote reservoir and immersion tanks) must be covered when not in use. Additionally, immersion type cold cleaning machines must have either a 2.54 cm (1-inch) water layer or a freeboard ratio of at least 0.75.

2.3.5.2. All vapor cleaning machines (vapor degreasers) must incorporate design and work practices which minimize the direct release of halogenated solvent to the atmosphere.

2.3.6. Units Containing ODS. The following criteria apply to direct atmospheric emissions of ODS, hydrofluorocarbons (HFC), and perfluorocarbons (PFC) from refrigeration equipment and ODS from fire suppression equipment. With regard to equipment containing controlled substances (Table 2.2), new equipment shall be prohibited from utilizing controlled substances, while existing equipment containing controlled substances shall comply with the gradual phase-out schedule. Contact the LEC to obtain the phase-out schedule and to obtain approval for laboratory and medical equipment exemptions.

2.3.6.1. Refrigerant Recovery/Recycling. All repairs, including leak repairs or services to appliances, industrial process refrigeration units, air conditioning units, or motor vehicle air conditioners, must be performed using commercially available refrigerant recovery/recycling equipment operated by trained personnel. Refrigerant technicians shall be trained in proper recovery/recycling procedures, leak detection, safety, shipping, and disposal in accordance with recognized industry standards or Bahraini equivalent.

2.3.6.2. Refrigerant Venting Prohibition. Any class I or class II ODS, HFC, and PFC refrigerant listed in Tables 2.2 and 2.3 shall not be intentionally released in the course of maintaining, servicing, repairing, or disposing of appliances, industrial process refrigeration units, air conditioning units, or motor vehicle air conditioners. De minimis releases associated with good faith attempts to recycle or recover ODS, HFC, and PFC refrigerants listed in Table

2.3 are not subject to this prohibition.

2.3.6.3. Refrigerant Leak Monitoring and Repair. Monitor and repair refrigeration equipment for leakage in accordance with the following criteria and repair, if found to be leaking.

2.3.6.3.1. Commercial Refrigeration Equipment. Commercial refrigeration equipment normally containing > 22.70 kg (50 pounds) of refrigerant must have leaks repaired if the appliance is leaking at a rate such that the loss of refrigerant will exceed 35 % of the total charge during a 12-month period.

2.3.6.3.2. Industrial Process Refrigeration Equipment. Industrial process refrigeration equipment normally containing > 22.70 kg (50 pounds) of refrigerant must have leaks repaired if the appliance is leaking at a rate such that the loss of refrigerant will exceed 35% of the total charge during a 12-month period.

2.3.6.3.3. Comfort Cooling Appliances. Comfort cooling appliances normally containing > 22.70 kg (50 pounds) of refrigerant and not covered by subparagraphs 2.3.6.3.1. or

2.3.6.3.2. of this chapter must have leaks repaired if the appliance is leaking at a rate such that the loss of refrigerant will exceed 15 % of the total charge during a 12-month period.

2.3.6.4. ODS Fire Suppression Agent (Halon) Venting Prohibition. Halons listed in

Tables 2.2 and 2.3 shall not be intentionally released into the environment while testing, maintaining, servicing, repairing, or disposing of halon-containing equipment or using such equipment for technician training. This venting prohibition does NOT apply to the following types of releases of halons listed in Table 2.3:

2.3.6.4.1. De minimis releases associated with good faith attempts to recycle or recover halons (i.e., release of residual halon contained in fully discharged total flooding fire extinguishing systems).

2.3.6.4.2. Emergency releases for the legitimate purpose of fire extinguishing, explosion, or other emergency applications for which the equipment or systems were designed.

2.3.6.4.3. Releases during the testing of fire extinguishing systems if each of the following is true: systems or equipment employing suitable alternative fire extinguishing agents are not available; release of extinguishing agent is essential to demonstrate equipment functionality; failure of system or equipment would pose great risk to human safety or the environment; and a simulant agent cannot be used.

2.3.7. Motor Vehicles. These criteria apply to DoD-owned motor vehicles as defined in paragraph 2.2.11.

2.3.7.1. All imported vehicles shall have a catalytic converter or equivalent form of emission control equipment.

2.3.7.2. All vehicles shall be inspected every two years to ensure that no tampering with factory-installed emission control equipment (catalytic converters or equivalent) has occurred.

2.3.7.3. If available on the local economy, use only unleaded gasoline in vehicles that are designed for this fuel.

2.3.7.4. Particulate emissions from diesel exhaust shall not exceed a concentration of 193 mg/m

2.3.8. Stack Heights. Hg is the good engineering practice stack height necessary to minimize downwash of stack emissions due to aerodynamic influences from nearby structures.

2.3.8.1. Stacks shall be designed and constructed to heights at least equal to the largest Hg calculated from either of the following two criteria:

2.3.8.1.1. Hg = H + 1.5L, where H is the height of the nearby structure measured from the ground level elevation at the base of the stack, and L is the lesser of height or projected width of the nearby structure(s). A structure is determined to be nearby when the stack is located within

5L of the structure envelope but not greater than 0.8 km (0.5 mile). This calculation shall be performed for each structure nearby the stack being studied to determine the greatest Hg.

2.3.8.1.2. Hg is the height demonstrated by a fluid model or a field study, which ensures that the emissions from a stack do not result in maximum ground-level concentrations of any air pollutant as a result of atmospheric downwash, wakes, or eddy effects created by the source itself, nearby structures, or nearby terrain features at least 40 % in excess of the maximum ground-level concentrations of any air pollutant experienced in the absence of such atmospheric downwash, wakes, or eddy effects. For purposes of this paragraph, ―nearby‖ means not greater than 0.8 km (0.5 mile), except that the portion of a terrain feature may be considered to be nearby which falls within a distance of up to 10 times the maximum height (Ht) of the feature, not to exceed 3.2 km (2 miles) if such feature achieves a height (Ht) 0.8 km (0.5 mile) from the stack that is at least 40 % of the good engineering practice stack height determined by the formulae provided in 2.3.8.1.1. of this part or 26 meters (85 feet), whichever is greater, as measured from the ground-level elevation at the base of the stack. The height of the structure or terrain feature is measured from the ground-level elevation at the base of the stack.

2.3.9. Emissions Monitoring. The following monitoring requirements shall apply to all installations, including steam/ hot water generating units. These requirements do not apply to motor vehicles.

2.3.9.1. Air emissions monitoring shall be conducted on a quarterly basis and averaged over an 8 hour period. Monitoring can be conducted more frequently if instructed by the LEC.

2.3.9.2. Installations shall submit results of the analyses to the LEC within 15 days of conducting measurements, or as instructed by the LEC.

2.3.9.3. NOx shall be monitored through the chemiluminescent method, or through any other approved method.

2.3.9.4. Particulate matter shall be monitored through the Tapered Element Oscillating

Membrane (TEOM) method, or through any other approved method.

2.3.9.5. . Installations releasing pollutants which do not conform to permissible limits may be granted a grace period of ten one month periods. Contact the LEC for grace period determination.‖

2.3.10. Emissions Reporting. Installations releasing air pollutant emissions to the environment shall maintain data forms for their stacks. Bahrain inspector requests to examine these forms should be coordinated through the LEC. Forms can be obtained through the LEC.

Installations should also consult the LEC to determine the period of time the forms should be kept. The forms shall contain the following information:

2.3.10.1. Name of company/ owner of the source of emissions

2.3.10.2. Source of emissions

2.3.10.3. Type of pollutants released

2.3.10.4. Concentration of pollutants

2.3.10.5. Point of emissions

2.3.10.6. Temperature

2.3.10.7. Stack height

2.3.10.8. Stack diameter

2.3.10.9. Location of stack

2.3.10.10. Speed/ velocity

2.3.10.11. Rate of emission

2.3.11. Volatile Organic Compounds. Installations shall establish appropriate cleaning methods, a good maintenance system, and continual inspection and control procedures at points where vapor emissions are likely for any activities utilizing VOCs.

Table 2.1. Emission Standards for Fuel Combustion Sources

Fuel Source Pollutants Emission Limits (mg/Nm unless otherwise specified)

(for units with size 10 –

100 MMBtu/hr)

Emission Limits (mg/Nm unless otherwise specified)

(for units with size

>100MMBtu/hr)

All Sources Visible Emissions 20% Opacity 20% Opacity

Carbon Monoxide

(CO)

100 100

Oil Fuel

(liquid)

Nitrogen Oxides

(NOx)

150 150

Sulfur Dioxide

(SO2)

0.43lb/MMBtu 0.43lb/MMBtu

Hanging Particles

(PM)

100 100 for units with size

<50MW or 171MMBtu/hr)

50 (for units with size equal to 50 MW or

171MMBtu/hr)

129 (for units with size

>171MMBtu/hr)

Gas Fuel Nitrogen Oxides

(NOx)

100 100

Sulfur Dioxide

(SO2)

2.3 lb/MMBtu 2.3 lb/MMBtu

Hydrogen Sulfide

(H2S)

150ppm or 228mg/Nm

150ppm or 228mg/Nm

Hanging Particles

(PM)

0.1lb/MMBtu 0.1lb/MMBtu

Coal-Derived

Gas Fuel

Nitrogen Oxides

(NOx)

- 645

Hanging Particles

(PM)

50 50

Sulfur Dioxide

(SO2)

500 500

Solid Fossil

Fuel

Nitrogen Oxides

(NOx)

- 852

Sulfur Dioxide

(SO2)

1460 1460

Hanging Particles 122 122

Other Solid

Fuel

Hanging Particles 0.3 lb/MMBtu 0.2 lb/MMBtu

Notes:

1. Gases shall be under dry conditions, temperature 273K, Pressure 101.325kpa, 15% O2 reference

2. If the % of H2S in gas is greater than the standard, SO2 shall be used to lower this limit.

Table 2.2. Controlled ODS in Bahrain

Groups Common

Product Name

Chemical

Formula

Chemical Name Description CAS No.

Group I (CFCs) CFC-11 (R11) CFCl3 Trichlorofluoromethane 75-69-4

CFC-12 (R12) CF2Cl2 Dichlorodifluoromethane 75-71-8

CFC-113 C2F3Cl3 1,1,2-Trichlorotrifluoroethane 76-13-1

CFC-114 C2F4Cl2 Dichlorotetrafluoroethane 76-14-2

CFC-115 C2F5Cl Monochloropentafluoroethane 76-15-3

Group II (Halons) Halon 1211 CF2BrCl Bromochlorodifluoromethane 353-59-3

Halon 1301 CF3Br Bromotrifluoromethane 75-63-8

Halon 2402 C2F4Br2 Dibromotetrafluoroethane 124-73-2

Group III Fully

Halogenated

Compounds

CFC-13 CClF3 Chlorotrifluoromethane 75-72-9

CFC-111 C2Cl5F Pentachloro-2-fluoroethane 354-56-3

CFC-112 C2Cl4F2 Tetrachlorodifluoroethane 76-12-0

CFC-211 C3Cl7F Heptachlorofluoropropane 422-78-6

CFC-212 C3F2Cl6 Hexachlorodifluoropropane 3182-26-1

CFC-213 C3Cl5F3 Pentachlorotrifluoropropane 2354-06-5

CFC-214 C3Cl4F4 Tetrachlorotetrafluoropropane 29255-31-0

CFC-215 C3Cl3F5 Trichloropentafluoropropane 4259-43-2

CFC-216 C3F6Cl2 Dichlorohexafluoropropane 661-97-2

CFC-217 C3F7Cl Chloroheptafluoropropane 422-86-6

Group IV - CCl4 Carbon Tetrachloride 56-23-5

Group V - CH3Br Methyl Bromide 74-83-9

- CH3CCl3 Methyl Chloroform 71-55-6

Group VI - HBFCs Hydrobromofluorocarbons -

Table 2.3. Additional Ozone Depleting Substances Controlled on DoD Installations

Class II

HCFC – 21 HCFC – 133a HCFC – 225cb HCFC – 243

HCFC – 22 HCFC – 141b HCFC – 226 HCFC – 244

HCFC – 31 HCFC – 142b HCFC – 231 HCFC – 251

HCFC – 121 HCFC – 151 HCFC – 232 HCFC – 252

HCFC – 122 HCFC – 221 HCFC - 233 HCFC – 253

HCFC – 123 HCFC – 222 HCFC – 234 HCFC – 261

HCFC – 124 HCFC – 223 HCFC – 235 HCFC – 262

HCFC – 131 HCFC – 224 HCFC – 241 HCFC – 271

HCFC – 132b HCFC – 225ca HCFC – 242

Table 2.4. Emission Standards for Incinerators

Pollutant Emission Standards

Incinerator

Type

Existing MWC units MWC units that begin new construction or undergo substantial modification

CISWI units

Rated Capacity 35-250 tpd >250 tpd 35-250 tpd >250tpd All units

Particulate 70 mg/dscm 27 mg/dscm 24 mg/dscm 70 mg/dscm

Opacity 10% 10% 10%

NOx N/A See Note 3 500 ppmv 150 ppmv 388 ppmv

SO2 50% reduction or 77 ppmv

75% reduction or 29 ppmv

80% reduction or 30 ppmv 20 ppmv

Dioxins/furans 125 ng/dscm See Note 4 13 ng/dscm 0.41 ng/dscm

Cadmium 0.10 mg/dscm 0.040 mg/dscm 0.020 mg/dscm 0.004 mg/dscm

Lead 1.6 mg/dscm 0.44 mg/dscm 0.20 mg/dscm 0.04 mg/dscm

Mercury 85% reduction or 0.080 mg/dscm 85% reduction or 0.080 mg/dscm 0.47 mg/dscm

HCl 50% reduction or 250 ppmv

95% reduction or 29 ppmv

80% reduction or 30 ppmv

95% reduction or 25 ppmv

62 ppmv

Fugitive ash 5% of hourly observation period 5% of hourly observation period N/A Notes:

1 Emission standard concentrations (mg/dscm, ppmv) are corrected to 7% oxygen, dry basis at standard conditions. mg/dscm = milligram per dry standard cubic meter, ng = nanogram, ppm = parts per million.

2 Construction or modifications that were undertaken pursuant to existing (or previous) FGS are not subject to these requirements. These criteria are not intended to require retrofitting of MWC units.

3 NOx limits for units rated > 250 tons/day (tpd) capacity: mass burn refractory-no limit; mass burn waterwall-205 ppmv; mass burn rotary waterwall: 250 ppmv;

refuse-derived fuel combustor-250 ppmv; fluidized bed combustor-180 ppmv.

4 Dioxins/furans limits for units rated >250 tpd capacity: MWC with electrostatic precipitator (ESP)-60 ng/dscm; MWC with non-ESP-30 ng/dscm.

30 TABLE OF CONTENTS

Table 2.5. Carbon Monoxide Operating Limits for Incinerators

Incinerator Type Existing

MWC units

MWC units that begin new construction or undergo substantial modification

CISWI

units

Rated Capacity 35-tpd

>250 tpd

35-250 tpd >250tpd All units

Fluidized bed 100 ppmv (4-hr avg)

100 ppmv (4-hr avg) ppmv

Fluidized bed, mixed fuel

(wood/refuse-derived fuel)

200 ppmv

(24-hr avg)

200 ppmv

(24-hr avg)

100 ppmv

(4-hr avg)

Mass burn rotary refractory 100 ppmv (4-hr avg)

100 ppmv (24-hr avg)

Mass burn rotary waterfall 250 ppmv

(24-hr avg)

100 ppmv (24-hr avg)

Mass burn waterfall and refractory

100 ppmv (4-hr avg)

100 ppmv (4-hr avg)

Mixed fuel-fired (pulverized coal/refuse-derived fuel)

150 ppmv (4-hr avg)

150 ppmv (4-hr avg)

Modular starved-air and excess air

50 ppmv (4-hr avg)

50 ppmv (4-hr avg)

Spreader stoker, mixed fuel-fired

(coal/refuse-derived fuel)

200 ppmv

(24-hr avg)

150 ppmv (24-hr avg)

Stoker, refuse-derived fuel 200 ppmv

(24-hr avg)

150 ppmv (24-hr avg)

Notes:

1. Compliance is determined by continuous emission monitoring systems.

2. Construction or modifications that were undertaken pursuant to existing (or previous) FGS are not subject to these requirements. These criteria are not intended to require retrofitting of MWC units.

Table 2.6. Air Emission Standards for Medical Waste Incinerators with a Capacity > 1

Ton Per Hour

Pollutants Limits (mg/m unless otherwise specified)

Total Plankton particles

Carbon Monoxide

Carbon Dioxide

Hydrogen Chloride

Hydrogen Fluoride

Nitric Oxide

Organic Compounds

Dioxins and Furans (In operating units with design capacity of > 50 kg/hour)

1 ng TEV/m

Refer to Table No. 2.8

Cadmium and its compounds (referred to as Cadmium) 0.1

Mercury and its compounds (referred to as Mercury) 0.1

Other heavy metal and their compounds Referred to as

Metal

[total of each Pb (Lead) As (Arsenic), CR

(Chrome)]

0.1

Notes:

Average daily values

Measurement of emissions produced once every 6 months

Measurement of emissions produced once every year

TEV means Total Equivalency Quantity (Toxic Equivalent). See Table 2.8.

Table 2.7. Air Emission Standards for Medical Waste Incinerators with a Capacity < 1

Ton Per Hour

Pollutants Limits (mg/m unless otherwise specified)

Total Plankton particles

Carbon Monoxide

Carbon Dioxide

Hydrogen Chloride

Organic Compounds

Dioxins and Furans (In operating units with design capacity of > 50kg/hour)

1 ng TEV/m

Refer to Table 2.8

Cadmium and its compounds (referred to as Cadmium) 0.1

Mercury and its compounds (referred to as Mercury) 0.1

Other heavy metal and their compounds Referred to as

Metal [total of each Pb (Lead) As (Arsenic), CR

(Chrome)]

0.1

Average daily values

Measurement of emissions produced once every 6 months

Measurement of emissions produced once every year

TEV means Total Equivalency Quantity (Toxic Equivalent). See Table 2.8.

Table 2.8. Dioxins and Furans

Chemical Substance(s) Equation Value/ Factor

2, 3, 7, 8, Tetrachlorapitrodioxin 1.0

1, 2, 3, 7, 8, Pentachlorapitrodioxin 0.5

1, 2, 3, 4, 7, 8, Hexachlorapitrodioxin 0.1

1, 2, 3, 7, 8, 9, Hexachlorapitrodioxin 0.1

1, 2, 3, 6, 7, 8, Hexachlorapitrodioxin 0.1

1, 2, 3, 4, 6, 7, 8, Heptachlorapitrodioxin 0.01

Octachlorapitrodioxin 0.001

2, 3, 7, 8, Tetrachlorapitrodioxin Furan 0.1

2, 3, 4, 7, 8, Pentachlorapitrodioxin Furan 0.5

1, 2, 3, 7, 8, Pentachlorapitrodioxin Furan 0.05

1, 2, 3, 4, 7, 8, Hexachlorapitrodioxin Furan 0.1

1, 2, 3, 7, 8, 9, Hexachlorapitrodioxin Furan 0.1

1, 2, 3, 6, 7, 8, Hexachlorapitrodioxin Furan 0.1

2, 3, 4, 6, 7, 8, Hexachlorapitrodioxin Furan 0.1

1, 2, 3, 4, 6, 7, 8, Heptachlorapitrodioxin Furan 0.01

1, 2, 3, 4, 5, 8, 9, Heptachlorapitrodioxin Furan 0.01

Octachlorapitrodioxin Furan 0.001 Notes:

TEV means Total Equivalency Quantity (Toxic Equivalent), being the sum total of the concentrations of each of the dioxin and furan compounds specified in the first column of this table…