45-X Product Data Sheets.pdf

Product Data Sheet Sika® Armatec®-110 EpoCem March 2020, Version 01.02 020302020050000003

PRODUCT DATA SHEET

Sika® Armatec®-110 EpoCem

BONDING PRIMER AND REINFORCEMENT CORROSION PROTECTION

PRODUCT DESCRIPTION

Sika® Armatec®-110 EpoCem is a cementitious epoxy resin compensated 3-component, solvent-free, coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection.

USES

Suitable in concrete repair as corrosion protection for reinforcement

Suitable as a bonding primer on mortar, steel, and on placing fresh, plastic concrete to existing hardened concrete

Protection to reinforcing steel in areas of thin concrete cover

CHARACTERISTICS / ADVANTAGES

Contains EpoCem® technology - improved bonding agent

Extended open times for repair mortars▪ Excellent adhesion to concrete and steel▪ Contains corrosion inhibitor▪ Good resistance to water and chloride penetration▪ High shear strength▪ Long pot life▪ Can be brushed on or applied using spray gun▪ Can be used exterior on-grade▪ Excellent bonding bridge for cement or epoxy based repair mortars

High strength, unaffected by moisture when cured▪ Non-flammable, solvent free▪

PRODUCT INFORMATION

Chemical Base Portland cement, epoxy resin, selected aggregates and additives.

Packaging Unit A B C ABC

3.5 gal (13.2 L)

47.6 oz (1.4 L)

122.1 oz (3.6 L)

46.82 lb (21.3 kg)

A + B in carton, C in bag

1.65 gal (6.2 L)

22.7 oz (0.67 L)

57.6 oz (1.7 L)

5.5 lb (2.5 kg) (4 bags)

Factory-proportioned units in a pail

Appearance / Color Component A White liquid Component B Colorless liquid Component C Gray powder

Shelf Life 12 months from date of production if stored properly in original, unopened and undamaged sealed packaging

Store dry at 40–95 °F (4–35 °C)Storage Conditions

1 / 4

Protect Component A and B from freezing. If frozen, discard.

Protect Component C from moisture. If damp, discard.

TECHNICAL INFORMATION

Compressive Strength 3 days 4,500 psi (31.0 MPa) 7 days 6,500 psi (44.8 MPa) 28 days 8,500 psi (58.6 MPa)

(ASTM C-109)

73 °F (23 °C)

50 % R.H.

Flexural Strength 28 days 1,250 psi (8.6 MPa) (ASTM C-348) 73 °F (23 °C)

50 % R.H.

Splitting Tensile Strength 28 days 600 psi (4.1 MPa) (ASTM C-496) 73 °F (23 °C)

50 % R.H.

Tensile Adhesion Strength Bond of steel reinforcement on concrete Sika® Armatec® 110 EpoCem coated

625 psi (4.3 MPa)

Epoxy coated 508 psi (3.5 MPa) Plain reinforcement 573 psi (4.0 MPa)

(ASTM C-1583)

73 °F (23 °C)

50 % R.H.

Slant Shear Strength Bonding agent properties (14 d. moist cure, plastic to hardened concrete) Wet on wet 2,800 psi (19.3 MPa) 24 hr. open time 2,600 psi (17.9 MPa)

(ASTM C-882)

73 °F (23 °C)

50 % R.H.

Permeability to Water Vapor Control 7.32 x 10-10 ft/sec 145 psi (10 bar) 8.92 x 10-15 ft/sec

Diffusion Resistance to Water Vapor μ H2O ~100

Permeability to CO2 μ CO2 ~14,000

Corrosion Test Time-to-Corrosion Study Sika® Armatec®-110 EpoCem more than tripled the time to corrosion▪ Reduced corrosion rate by over 40 %▪

APPLICATION INFORMATION

Fresh Mortar Density A+B+C ~125 lb/ft3 (~2.0 kg/l)

Coverage Bonding agent 80 ft2/gal (7.4 m2/l) Corrosion Protection 40 ft2/gal (3.7 m2/l)

(Coverage figures do not include allowance for surface profile and porosity or material waste)

Layer Thickness Min. thickness of 1 coat Coat Bonding agent 20 mils 1 Corrosion Protection 20 mils 2

Product Temperature 65°-75°F (18°-24°C)

Ambient Air Temperature 40–95 °F (5–35 °C)

Substrate Temperature 40–95 °F (5–35 °C)

Pot Life ~ 90 minutes

Sika repair mortars and non-fast setting concrete can be applied on Sika® Armatec®-110 EpoCem within a maximum time of:

Waiting / Recoat Times

Product Data Sheet Sika® Armatec®-110 EpoCem March 2020, Version 01.02 020302020050000003

2 / 4

Temperature Maximum Waiting Time 80°- 95 °F (26°- 35 °C) 6 hours 65°-79 °F (18°- 26 °C) 12 hours 50°- 64° F (10°- 17° C) 16 hours 40°- 49° F (4°- 9° C) wet-on-wet

APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Concrete Free from dust, loose material, surface contamination and materials which reduce bond or prevent suction or wetting by repair materials.

Delaminated, weak, damaged and deteriorated concrete and where necessary sound concrete shall be removed by suitable means.

Substrate must be Saturated Surface Dry (SSD) with no standing water.

Steel reinforcement

Rust, scale, mortar, concrete, dust and other loose and deleterious material which reduces bond or contributes to corrosion shall be removed by blast cleaning or other means of mechanical abrasion and reinforcement.

Should be fully exposed and have all corrosion removed.

MIXING

Sika® Armatec®-110 EpoCem can be mixed with a low-speed (< 250 rpm) electric drill mixer.

Shake components A and B thoroughly before opening.▪ Pour liquid components A and B into a suitable mixing vessel and mix for 30 seconds.

While still mixing components A and B slowly add powder component C.

Mix the three components together for a minimum 3 minutes until blend is uniform and free of lumps, minimizing addition of air.

Mix only the quantity that you can be applied within the pot life.

DO NOT ADD WATER.▪

APPLICATION

As reinforcement corrosion protection Apply by stiff-bristle brush or spray at 80 ft2 /gal.▪ Take special care to properly coat the underside of the totally exposed steel.

Allow coating to dry 2-3 hours at 73 °F, then apply a second coat at the same coverage.

Allow to dry again before the repair mortar or concrete is applied.

Pour or place repair within 7 days▪

As a bonding primer Apply using a stiff-bristle brush or broom. To achieve good bond, Sika® Armatec®-110 EpoCem must be applied well into the substrate, filling all pores and ensure complete coverage of all surface irregularities (minimum layer thickness 1/64ʺ (0.5 mm).

Spray apply with Goldblatt Pattern Pistol or equal equipment.

Apply the freshly mixed patching mortar or concrete wet on wet, or up to the maximum recommended open time, onto the bonding slurry.

CURING TREATMENT

Sika® Armatec®-110 EpoCem must be protected against contamination and rain until application of the repair mortar.

CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use. Hardened material can only be mechanically removed.

LIMITATIONS

Avoid application in direct sun and/or strong wind and/or rain.

Do not add water.▪ Not a vapor barrier.▪ Apply only to sound, prepared substrates.▪ Not recommended for use with expansive grouts and SikaQuicks

Use of semi-dry mortars onto Sika® Armatec®-110 EpoCem must be applied “wet on wet”

When used in overhead applications with hand placed patching mortars, use “wet on wet” for maximum mortar built thickness.

Substrate profile as specified by the overlay or repair material is still required.

As with all cement based materials, avoid contact with aluminum to prevent adverse chemical reaction and possible product failure. Insulate potential areas of contact by coating aluminum bars, rails, posts etc. with an appropriate epoxy such as Sikadur® Hi-Mod 32.

Product Data Sheet Sika® Armatec®-110 EpoCem March 2020, Version 01.02

3 / 4

BASIS OF PRODUCT DATA

Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions.

OTHER RESTRICTIONS

See Legal Disclaimer.

ENVIRONMENTAL, HEALTH AND SAFETY

For further information and advice regarding transportation, handling, storage and disposal of chemical products, user should refer to the actual Safety Data Sheets containing physical, environmental, toxicological and other safety related data. User must read the current actual Safety Data Sheets before using any products. In case of an emergency, call CHEMTREC at 1-800-424-9300, International 703-527-3887.

DIRECTIVE 2004/42/CE - LIMITATION OF EMISSIONS OF

VOC

A+B+C combined 50 g/l

LEGAL DISCLAIMER

• KEEP CONTAINER TIGHTLY CLOSED

• KEEP OUT OF REACH OF CHILDREN

• NOT FOR INTERNAL CONSUMPTION

• FOR INDUSTRIAL USE ONLY

• FOR PROFESSIONAL USE ONLY

Prior to each use of any product of Sika Corporation, its subsidiaries or affiliates (“SIKA”), the user must always read and follow the warnings and instructions on the product’s most current product label, Product Data Sheet and Safety Data Sheet which are available at usa.sika.com or by calling SIKA’s Technical Service Department at 1-800-933-7452. Nothing contained in any SIKA literature or materials relieves the user of the obligation to read and follow the warnings and instructions for each SIKA product as set forth in the current product label, Product Data Sheet and Safety Data Sheet prior to use of the SIKA product.

SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties on the current Product Data Sheet if used as directed within the product’s shelf life. User determines suitability of product for intended use and assumes all risks. User’s and/or buyer’s sole remedy shall be limited to the purchase price or replacement of this product exclusive of any labor costs.

NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL

APPLY INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL

THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.

SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS

PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT

OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD

BY OTHERS.

Sale of SIKA products are subject to the Terms and Conditions of Sale which are available at https://usa.sika.com/en/group/SikaCorp/termsandconditions.html or by calling 1-800-933-7452.

Sika Corporation 201 Polito Avenue Lyndhurst, NJ 07071 Phone: +1-800-933-7452 Fax: +1-201-933-6225 usa.sika.com

Sika Mexicana S.A. de C.V.

Carretera Libre Celaya Km. 8.5 Fracc. Industrial Balvanera Corregidora, Queretaro C.P. 76920 Phone: 52 442 2385800 Fax: 52 442 2250537

SikaArmatec-110EpoCem-en-US-(03-2020)-1-2.pdf

Product Data Sheet Sika® Armatec®-110 EpoCem March 2020, Version 01.02

4 / 4

SikaTop®-122 Plus November 2022, Version 01.06 020302040070000021

PRODUCT DATA SHEET

SikaTop®-122 Plus Two-component, polymer-modified, cementitious, trowel-grade mortar plus Sika FerroGard® 901 penetrating corrosion inhibitor

PRODUCT DESCRIPTION

SikaTop®-122 Plus is a two-component, polymer-modified, portland cement based, fast-setting, trowel-grade mortar. It is a high-performance repair mortar for horizontal and vertical surfaces and offers the additional benefit of Sika FerroGard® 901, a penetrating corrosion inhibitor.

USES

On grade, above and below grade on concrete and mortar.

On horizontal surfaces.▪ As a structural repair material for parking structures, industrial plants, walkways, bridges, tunnels, dams, ramps, floors, etc.

To level concrete surfaces.▪ As an overlay system for topping/resurfacing concrete.▪

CHARACTERISTICS / ADVANTAGES

Extremely low shrinkage proven by four industry standard test methods

High compressive and flexural strengths▪ High abrasion resistance▪ Increased freeze/thaw durability and resistance to deicing salts

Compatible with coefficient of thermal expansion of concrete - Passes ASTM C-884

Increased density - improved carbon dioxide resistance (carbonation) without adversely affecting water vapor transmission (not a vapor barrier)

Sika FerroGard® 901, a penetrating corrosion inhibitor -reduces corrosion even in the adjacent concrete

APPROVALS / STANDARDS

USDA certifiable for the food industry▪ ANSI/NSF Standard 61 potable water compliant▪ Tested per ICRI guideline for inorganic repair material data sheet protocol guideline n°320.3R

PRODUCT INFORMATION

Packaging Component A Component B 1 gal (3.78 L) jug 4/carton

61.5 lb (28.9 kg) bag

Shelf Life 12 months from date of production if stored properly in original, unopened and undamaged sealed packaging

Storage Conditions Store dry at 40–95 °F (4–35 °C) Protect Component A from freezing. If frozen, discard.

Protect Component B from moisture. If damp, discard.

Appearance / Color Concrete gray when mixed

1 / 5

Density 136 lbs/ft3 (2.18 kg/L) (ASTM C-138)

TECHNICAL INFORMATION

Compressive Strength 1 day 2,500 psi (17.2 MPa) 7 days 5,300 psi (36.5 MPa) 28 days 7,000 psi (48.3 MPa)

(ASTM C-109)

73 °F (23 °C)

50 % R.H.

Modulus of Elasticity in Compression 28 days 3.0x106 psi (ASTM C-469) 73 °F (23 °C)

50 % R.H.

Flexural Strength 28 days 1,500 psi (10.3 MPa) (ASTM C-293) 73 °F (23 °C)

50 % R.H.

Tensile Strength 28 days 2,000 psi (13.8 MPa) (ASTM C-882 modified)*

* Mortar scrubbed into substrate at 73 °F (23 °C) and 50 % R.H.

Splitting tensile strength 28 days 500 psi (3.4 MPa) (ASTM C-496) 73 °F (23 °C)

50 % R.H.

Pull-Out Resistance 7 days >300 psi (2.1 MPa) 28 days 400 psi (2.8 MPa)

(ASTM C-1583)

73 °F (23 °C)

50 % R.H.

Shrinkage 28 days 1’’x1’’x11-1/4’’ specimen

< 0.05 %

3’’x3’’x11-1/4’’ specimen

< 0.021 %

(ASTM C-157

modified

(mod. ICRI 320.3R)) 73 °F (23 °C)

50 % R.H.

Ring test Duration >70 days Average Max Strain -9 μstrain Average Stress Strain 0.49 psi/day Potential for Cracking Low

(ASTM C-1581)

73 °F (23 °C)

50 % R.H.

Baenziger block 90 days No cracking

Rapid Chloride Permeability 28 days < 500 C (ASTM C-1202

AASHOT T-277)

Freeze-Thaw Stability 300 cycles 98 % (ASTM C-666)

APPLICATION INFORMATION

Mixing Ratio Plant-proportioned kit, mix entire unit.

Fresh mortar density 136 lbs/ft3 (2.18 kg/l) (ASTM C-138)

Coverage Neat 0.51 ft3 (0.02 m3) per unit Extended with 42 lb (19 kg) of 3/8" (9.5 mm) gravel

0.75 ft3 (0.03 m3) per unit

(Coverage figures do not include allowance for surface profile and porosity or material waste)

Layer Thickness Min. Max. in one lift Neat 1/8" (3.2 mm) 1" (25 mm) Extended 1" (25.4 mm) 4" (101.6 mm)

Product Data Sheet SikaTop®-122 Plus November 2022, Version 01.06 020302040070000021

2 / 5

Product Temperature 65–75 °F (18–24 °C)

Ambient Air Temperature > 45 °F (7 °C)

Substrate Temperature > 45 °F (7 °C)

Set Time 35–70 minutes (ASTM C-266)

Final set time > 90 minutes (ASTM C 266) 73o F (23o C), 50% R.H.

Finishing time 50–120 minutes Note: All times start after adding Component ‘B’ to Component ‘A’ and are highly affected by temperature, relative humidity, substrate temperature, wind, sun and other job site conditions.

BASIS OF PRODUCT DATA

Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions.

LIMITATIONS

Do not use solvent-based curing compound.▪ Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI. For additional information, contact Technical Service.

For additional information on substrate preparation, refer to ICRI Guideline No.310.2R Coatings, Polymer Overlays, and Concrete Repair.

If aggressive means of substrate preparation is employed, substrate strength should be tested in accordance with ACI 503 Appendix A prior to the repair application.

As with all cement based materials, avoid contact with aluminum to prevent adverse chemical reaction and possible product failure. Insulate potential areas of contact by coating aluminum bars, rails, posts etc. with an appropriate epoxy such as Sikadur 32 Hi-Mod.

Refer to Sika® Antisol®-250 W product data sheet for use.

ENVIRONMENTAL, HEALTH AND SAFETY

For further information and advice regarding transportation, handling, storage and disposal of chemical products, user should refer to the actual Safety Data Sheets containing physical, environmental, toxicological and other safety related data. User must read the current actual Safety Data Sheets before using any products. In case of an emergency, call CHEMTREC at 1-800-424-9300, International 703-527-3887.

APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Concrete, mortar, and masonry products must be clean ▪ and sound.

Remove all deteriorated concrete, dirt, oil, grease, and other bond-inhibiting materials from the area to be repaired.

Be sure repair area is not less than 1/8” (3.2mm) in depth.

Preparation work should be done by high pressure water blast, scabbler or other appropriate mechanical means to obtain an exposed aggregate surface profile of ±1/16"-1/8" (1.6-3.2 mm) (CSP-5-6).

To ensure optimum repair results, the effectiveness of decontamination and preparation should be assessed by a pull-off test.

Saw cutting of edges is preferred and a dovetail is recommended.

Substrate should be Saturated Surface Dry (SSD) with clean water prior to application. No standing water should remain during application.

PRIMING

Reinforcing steel: Steel reinforcement should be thoroughly prepared by mechanical cleaning to remove all traces of rust. Where corrosion has occurred due to the presence of chlorides, the steel should be high pressure washed with clean water after mechanical cleaning. For priming of reinforcing steel use Sika® Armatec® 110 EpoCem (consult PDS).

Concrete Substrate: Prime the prepared substrate with a brush or sprayed applied coat of Sika® Armatec® 110 EpoCem (consult PDS). Alternately, a scrub coat of SikaTop®-122 Plus can be applied prior to placement of the mortar. The repair mortar has to be applied into the wet scrub coat before it dries.

Product Data Sheet SikaTop®-122 Plus November 2022, Version 01.06

3 / 5

MIXING

Pour approximately 7/8 of Component ‘A’ into the mixing container.

Add Component ‘B’ (powder) while mixing continuously.

Mix mechanically with a low-speed drill (400–600 rpm) and mixing paddle or mortar mixer.

Add remaining Component ‘A’ (liquid) to mix if a more loose consistency is desired.

Mix to a uniform consistency, maximum 3 minutes.▪ Thorough mixing and proper proportioning of the two components is necessary.

Refer to ACI 306 Guidelines when there is a need to place this product in cold & hot temperatures. Thinner application will be more sensitive to the temperature

EXTENSION WITH AGGREGATES

For applications greater than 1" (25.4 mm) in depth, add 3/8" (9.5 mm) coarse aggregate.

Pour all of Component ‘A’ into mixing container.▪ Add all of Component ‘B’ while mixing, then introduce 3/8" (9.5 mm) coarse aggregate at desired quantity.

Mix to uniform consistency, maximum 3 minutes.▪ The aggregate must be non-reactive (reference ASTM C-1260, C-227 and C-289), clean, well graded, Saturated Surface Dry (SSD), have low absorption and high density, and comply with ASTM C-33 size number 8 per Table 2.

Do not use limestone aggregate.▪ Variances in the quality of the aggregate will affect the physical properties of SikaTop®-122 Plus and may result in different strengths.

The addition rate is 42 lb (19 kg) of aggregate per bag.

It is approximately 3.0-4.5 gallons (11.3-17.0 L) by loose volume of aggregate.

APPLICATION

SikaTop®-122 Plus must be scrubbed into the substrate, filling all pores and voids.

Force material against edge of repair, working toward center.

After filling repair, consolidate, then screed.▪ Allow mortar or concrete to set to desired stiffness, then finish with wood or sponge float for a smooth surface, or broom or burlap-drag for a rough finish.

CURING TREATMENT

As per ACI recommendations for Portland cement concrete, curing is required.

Moist cure with wet burlap and polyethylene, a fine mist of water or a water Sika® Antisol®-250 W* compatible curing compound meeting ASTM C-309.

Curing compounds adversely affect the adhesion of following lifts of mortar, leveling mortar or protective coatings.

Moist curing should commence immediately after finishing.

Protect freshly applied mortar from direct sunlight, wind, rain and frost.

To prevent from freezing, cover with insulating material.

* Pretesting of curing compound is recommended.

OTHER RESTRICTIONS

See Legal Disclaimer.

Product Data Sheet SikaTop®-122 Plus November 2022, Version 01.06

4 / 5

LEGAL DISCLAIMER

• KEEP CONTAINER TIGHTLY CLOSED

• KEEP OUT OF REACH OF CHILDREN

• NOT FOR INTERNAL CONSUMPTION

• FOR INDUSTRIAL USE ONLY

• FOR PROFESSIONAL USE ONLY

Prior to each use of any product of Sika Corporation, its subsidiaries or affiliates (“SIKA”), the user must always read and follow the warnings and instructions on the product’s most current product label, Product Data Sheet and Safety Data Sheet which are available at usa.sika.com or by calling SIKA’s Technical Service Department at 1-800-933-7452. Nothing contained in any SIKA literature or materials relieves the user of the obligation to read and follow the warnings and instructions for each SIKA product as set forth in the current product label, Product Data Sheet and Safety Data Sheet prior to use of the SIKA product.

SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties on the current Product Data Sheet if used as directed within the product’s shelf life. User determines suitability of product for intended use and assumes all risks. User’s and/or buyer’s sole remedy shall be limited to the purchase price or replacement of this product exclusive of any labor costs.

NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL

APPLY INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL

THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.

SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS

PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT

OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD

BY OTHERS.

Sale of SIKA products are subject to the Terms and Conditions of Sale which are available at https://usa.sika.com/en/group/SikaCorp/termsandconditions.html or by calling 1-800-933-7452.

Sika Corporation 201 Polito Avenue Lyndhurst, NJ 07071 Phone: +1-800-933-7452 Fax: +1-201-933-6225 usa.sika.com

SikaTop-122Plus-en-US-(11-2022)-1-6.pdf

Product Data Sheet SikaTop®-122 Plus November 2022, Version 01.06

5 / 5

SikaTop®-123 Plus November 2020, Version 01.03 020302040070000022

PRODUCT DATA SHEET

SikaTop®-123 Plus Two-component, polymer-modified, cementitious, non-sag mortar plus Sika FerroGard® 901 penet-rating corrosion inhibitor

PRODUCT DESCRIPTION

SikaTop®-123 Plus is a two-component, polymer-modified, Portland cement-based, fast-setting, non-sag mortar. It is a high performance repair mortar for vertical and overhead surfaces and offers the additional benefit of Sika FerroGard® 901, a penetrating corrosion inhibitor included in its formulation.

USES

On grade, above and below grade on concrete and mortar.

On vertical and overhead surfaces.▪ As a structural repair material for parking structures, industrial plants, walkways, bridges, tunnels, dams and ramps.

Approved for repairs over cathodic protection systems▪

CHARACTERISTICS / ADVANTAGES

Extremely low shrinkage proven by four industry standard test methods.

High compressive and flexural strengths.▪ Increased freeze/thaw durability and resistance to deicing salts.

Increased density - improved carbon dioxide resistance (carbonation) without adversely affecting water vapor transmission (not a vapor barrier).

Enhanced with Sika FerroGard® 901, a penetrating corrosion inhibitor - reduces corrosion even in the adjacent concrete.

Compatible with coefficient of thermal expansion of concrete - Passes ASTM C 884.

APPROVALS / STANDARDS

USDA certifiable for incidental food contact▪ ANSI/NSF Standard 61 potable water approved compliant.

Tested per ICRI Guidline NO. 320.3R for inorganic repair material data sheet protocol

PRODUCT INFORMATION

Packaging Component A 1 gal (3.68 L) jug - 4/carton Component B 44 lb. (20 kg) bag

Appearance / Color Gray powder

Shelf Life 12 months from date of production if stored properly in original, unopened and undamaged sealed packaging

Store dry at 40–95 °F (4–35 °C).Storage Conditions

1 / 6

Protect Component ‘B’ from moisture. If damp, discard material Protect Component ‘A’ from freezing. If frozen, discard.

Product Data Sheet SikaTop®-123 Plus November 2020, Version 01.03 020302040070000022

2 / 6

Compressive Strength 1 day 3,000 psi (20.7 MPa) 7 days 4,000 psi (27.6 MPa) 28 days 6,000 psi (41.4 MPa)

(ASTM C-109)

73 °F (23 °C)

50 % R.H.

Modulus of Elasticity in Compression 2.94 x 106 psi (ASTM C-469)

Flexural Strength 28 days 1,500 psi (10.3 MPa) (ASTM C-293) 73 °F (23 °C)

50 % R.H.

Splitting tensile strength 28 days 900 psi (6.2 MPa) (ASTM C-496) 73 °F (23 °C)

50 % R.H.

Tensile Adhesion Strength 28 days 2,000 psi (13.8 MPa) (ASTM C-882 modified)

* Mortar scrubbed into substrate at 73 °F (23 °C) and 50 % R.H.

Pull-Out Resistance 28 days 500 psi (3.4 MPa) Substrate failure

(ASTM C-1583)

Shrinkage 28 days 1x1x11-1/4’’ specimen

0.05 %

28 days 3x3x11-1/4’’ specimen

0.038 %

(ASTM C-157,

mod. ICRI 320.3R)

Ring test > 70 days Average Max Strain - 36 μstrain Average Stress Strain 4.92 psi/day Potential for Cracking Low

(ASTM C-1581)

Baenziger block 90 days No cracking

Freeze-Thaw Stability 300 cycles 98 % (ASTM C-666)

Rapid Chloride Permeability 28 days < 500 C (ASTM C-1202

AASHTO T-277)

APPLICATION INFORMATION

Fresh mortar density 132 lb/ft3 (2.2 kg/l) (ASTM C-138)

Coverage 0.39 ft3 (0.01 m3) per bag (Coverage figures do not include allowance for surface profile and porosity or material waste)

Layer Thickness Min. Max.

1/8 " (3 mm) 1.5" (38 mm)

Product Temperature 65–75 °F (18–24 °C)

Ambient Air Temperature > 45 °F (7 °C)

Substrate Temperature > 45 °F (7 °C)

Set Time 15 - 40 min. (ASTM C-266)

Final set time < 60 min. (ASTM C-266)

Product Data Sheet SikaTop®-123 Plus November 2020, Version 01.03

3 / 6

Finishing time 20–60 minutes Note: All times start after adding Component ‘B’ to Component ‘A’ and are highly affected by temperature, relative humidity, substrate temperature, wind, sun and other job site conditions.

BASIS OF PRODUCT DATA

Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions.

ENVIRONMENTAL, HEALTH AND SAFETY

For further information and advice regarding transportation, handling, storage and disposal of chemical products, user should refer to the actual Safety Data Sheets containing physical, environmental, toxicological and other safety related data. User must read the current actual Safety Data Sheets before using any products. In case of an emergency, call CHEMTREC at 1-800-424-9300, International 703-527-3887.

DIRECTIVE 2004/42/CE - LIMITATION OF EMISSIONS OF

VOC

0 g/l (EPA method 24)

LIMITATIONS

Do not use solvent-based curing compound.▪ Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI.

For additional information on substrate preparation, refer to ICRI Guideline No. 310.2R.

If aggressive means of substrate preparation is employed, substrate strength should be tested in accordance with ACI 503 Appendix A prior to the repair application.

As with all cement based materials, avoid contact with aluminum to prevent adverse chemical reaction and possible product failure. Insulate potential areas of contact by coating aluminum bars, rails, posts etc. with an appropriate epoxy such as Sikadur® 32, Hi-Mod.

APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Surface preparation Surface must be clean and sound. Remove all deteriorated concrete, dirt, oil, grease, and other bond-inhibiting materials from the area to be repaired.

Be sure repair area is not less than 1/8" (3 mm) in depth.

Preparation work should be done by high pressure water blast, scabbler or other appropriate mechanical means to obtain an exposed aggregate surface profile of ±1/16" (1.6 mm) (CSP-5).

To ensure optimum repair results, the effectiveness of decontamination and preparation should be assessed by a pull-off test.

Saw cutting of edges is preferred and a dovetail is recommended.

Substrate should be Saturated Surface Dry (SSD) with clean water prior to application. No standing water should remain during application.

Priming

Reinforcing steel: Steel reinforcement should be thoroughly prepared by mechanical cleaning to remove all traces of rust. Where corrosion has occurred due to the presence of chlorides, the steel should be high pressure washed with clean water after mechanical cleaning. For priming of reinforcing steel use Sika® Armatec® 110 EpoCem (consult PDS).

Concrete Substrate:

Prime the prepared substrate with a brush or sprayed ▪

Product Data Sheet SikaTop®-123 Plus November 2020, Version 01.03

4 / 6 applied coat of Sika® Armatec® 110 EpoCem (consult

PDS).

Alternately, a scrub coat of SikaTop®-123 Plus can be applied prior to placement of the mortar. The repair mortar has to be applied into the wet scrub coat before it dries.

MIXING

Pour Component ‘A’ into mixing container.▪ Add Component ‘B’ while mixing continuously.▪ Mix mechanically with a low-speed drill (400–600 rpm) and mixing paddle or mortar mixer.

Mix to a uniform consistency, maximum 3 minutes.▪ Manual mixing can be tolerated only for less than a full unit. Thorough mixing and proper proportioning of the two components is necessary.

APPLICATION

SikaTop®-123 Plus must be scrubbed into the substrate, filling all pores and voids.

Force material against edge of repair, working toward center.

After filling repair, consolidate, then screed.▪ Material may be applied in multiple lifts.▪

Multiple lifts

Where multiple lifts are required score top surface of each lift to produce a roughened surface for next lift.

Allow preceding lift to reach initial set, 30 minutes minimum, before applying fresh material.

Substrate should be Saturated Surface Dry (SSD) with clean water prior to application. No standing water should remain during application.

Scrub fresh mortar into preceding lift.▪ Allow mortar or concrete to set to desired stiffness, then finish with wood or sponge float for a smooth surface.

CURING TREATMENT

As per ACI recommendations for Portland cement concrete, curing is required.

Moist cure with wet burlap and polyethylene, a fine mist of water or a water based* compatible curing compound (ASTM C-309).

Curing compounds adversely affect the adhesion of following lifts of mortar, leveling mortar or protective coatings.

Moist curing should commence immediately after finishing.

Protect freshly applied mortar from direct sunlight, wind, rain and frost.

* Pretesting of curing compound is recommended.

OTHER RESTRICTIONS

See Legal Disclaimer.

LEGAL DISCLAIMER

• KEEP CONTAINER TIGHTLY CLOSED

• KEEP OUT OF REACH OF CHILDREN

• NOT FOR INTERNAL CONSUMPTION

• FOR INDUSTRIAL USE ONLY

• FOR PROFESSIONAL USE ONLY

Prior to each use of any product of Sika Corporation, its subsidiaries or affiliates (“SIKA”), the user must always

Product Data Sheet SikaTop®-123 Plus November 2020, Version 01.03

5 / 6 read and follow the warnings and instructions on the product’s most current product label, Product Data Sheet and Safety Data Sheet which are available at usa.sika.com or by calling SIKA’s Technical Service Department at 1-800-933-7452. Nothing contained in any SIKA literature or materials relieves the user of the obligation to read and follow the warnings and instructions for each SIKA product as set forth in the current product label, Product Data Sheet and Safety Data Sheet prior to use of the SIKA product.

SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties on the current Product Data Sheet if used as directed within the product’s shelf life. User determines suitability of product for intended use and assumes all risks. User’s and/or buyer’s sole remedy shall be limited to the purchase price or replacement of this product exclusive of any labor costs.

NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL

APPLY INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL

THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.

SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS

PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT

OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD

BY OTHERS.

Sale of SIKA products are subject to the Terms and Conditions of Sale which are available at https://usa.sika.com/en/group/SikaCorp/termsandconditions.html or by calling 1-800-933-7452.

Sika Corporation 201 Polito Avenue Lyndhurst, NJ 07071 Phone: +1-800-933-7452 Fax: +1-201-933-6225 usa.sika.com

Sika Mexicana S.A. de C.V.

Carretera Libre Celaya Km. 8.5 Fracc. Industrial Balvanera Corregidora, Queretaro C.P. 76920 Phone: 52 442 2385800 Fax: 52 442 2250537

SikaTop-123Plus-en-US-(11-2020)-1-3.pdf

Product Data Sheet SikaTop®-123 Plus November 2020, Version 01.03

6 / 6

SikaGrout®-212 August 2018, Version 01.02 020201010010000002

PRODUCT DATA SHEET

SikaGrout®-212 General Purpose cementitious grout

PRODUCT DESCRIPTION

SikaGrout®-212 is a one-component, ready to mix, free flowing, non-shrink, cementitious grout with a unique 2-stage shrinkage compensating mechanism.

USES

General purpose grouting▪ Machine and column base plates▪ Anchor rods, bearing plates▪ Ram in place as a dry pack▪ Trowel-apply as a medium flow▪ Pour or pump as high flow▪ Bedding joints in pre-cast concrete sections▪ Filling cavities, voids, gaps and recesses▪ On grade, above and below grade▪ Indoors and out▪

CHARACTERISTICS / ADVANTAGES

Easy to use (ready to mix powder)▪ Shrinkage compensated properties in both the plastic and hardened states

Multiple fluidity with a single component▪ Good bond to concrete▪ Non-metallic, will not stain or rust▪ Contains no chloride▪ Blend of shrinkage-reducing and plasticizing/water-reducing agents

Low heat build-up▪ Excellent for pumping: does not segregate, even at high flow. No build-up on equipment hopper

Superior freeze/thaw resistance▪ Resistant to oil and water▪

APPROVALS / STANDARDS

Meets ASTM C-1107 (Grade C)▪ Shows positive expansion when tested in accordance with ASTM C-827

SikaGrout®-212 is USDA certifiable▪

PRODUCT INFORMATION

Chemical Base Cement, selected fillers and aggregates, special additives

Packaging 50 lb (22.7 kg) bag

Appearance / Color Gray powder

Shelf Life 12 months from date of production if stored properly in original, unopened and undamaged sealed packaging

Storage Conditions Store dry at 40–95 °F (4–35 °C) Protect from moisture. If damp, discard material

1 / 4

Compressive Strength Plastic Flowable Fluid 1 day 4,500 psi

(31 MPa) 3,500 psi (24.1 MPa)

2,700 psi (18.6 MPa)

7 days 6,100 psi (42 MPa)

5,700 psi (39.3 MPa)

5,500 psi (37.9 MPa)

28 days 7,500 psi (51.7 MPa)

6,200 psi (42.7 MPa)

5,800 psi (40 MPa)

(ASTM C-942)

73 °F (23 °C)

50 % R.H

Flexural Strength 28 days 1,400 psi (9.6 MPa)

1,200 psi (8.2 MPa)

1,000 psi (6.8 MPa)

(ASTM C-293)

73 °F (23 °C)

50 % R.H

Splitting Tensile Strength 28 days 600 psi (4.1 MPa)

575 psi (3.9 MPa)

500 psi (3.4 MPa)

(ASTM C-496)

73 °F (23 °C)

50 % R.H

Tensile Adhesion Strength 28 days 2,000 psi (13.7 MPa)

1,900 psi (13.1 MPa)

1,900 psi (13.1 MPa)

(ASTM C-882

modified)

73 °F (23 °C) 50 % R.H

Expansion 28 days +0.021 % +0.056 % +0.027 % (ASTM C-1090) 73 °F (23 °C)

50 % R.H.

APPLICATION INFORMATION

Mixing Ratio Plastic Flowable Fluid 6 pt 6.5 pt 8.5 pt

Coverage 0.44 ft3 (0.01 m3) at fluid consistency (Coverage figures do not include allowance for surface profile and porosity or material waste)

Layer Thickness Min. Max.

1/2" (12.7 mm) 4" (101.6 mm)

Thicker applications can be achieved. Contact Sika® Technical Services Department for further information.

Flowability Plastic1 Flowable1 Fluid2

100–124 % 124–145 % 20–40 sec

(ASTM C-14371

ASTM C-9392)

Product Temperature 65–75 °F (18–24 °C)

Ambient Air Temperature > 45 °F (7 °C)

Substrate Temperature > 45 °F (7 °C)

Pot Life ~15 minutes As the temperature will affect the pot life, application temperature:

Above 73 °F (23 °C) will reduce the pot life and flow▪ Below 73 °F (23 °C) will extend the pot life and flow▪

Set Time Plastic Flowable Fluid Initial 3.5–4.5 h 4.0–5.0 h 4.5–6.5 h Final 4.5–5.5 h 5.5–6.5 h 6.0–8.0 h

(ASTM C-266)

73 °F (23 °C)

50 % R.H

Product Data Sheet SikaGrout®-212 August 2018, Version 01.02 020201010010000002

2 / 4

APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Remove all dirt, oil, grease, and other bond-inhibiting materials by mechanical means.

Anchor bolts to be grouted must be de-greased with suitable solvent.

Concrete must be sound and roughened to a CSP 4 or higher to promote mechanical adhesion.

Prior to pouring, surface should be brought to a Saturated Surface Dry (SSD) condition.

Steel should be cleaned and prepared thoroughly by blastcleaning to a white metal finish.

Follow standard industry and Sika® guidelines for use as an anchoring epoxy.

Where grout-tight form is difficult to achieve, use SikaGrout®-212 in dry pack consistency.

FORMING

For pourable grout, construct forms to retain grout without leakage.

Should be lined or coated with bond-breaker for easy removal.

Should be sufficiently high to accommodate head of grout.

MIXING

Pour the water in the recommended proportion into a suitable mixing container.

While mixing slowly, add the powder to the water.▪ Mix thoroughly for 3 minutes with low speed (< 500 rpm) hand drill mixer to avoid entraining too much air and until homogenous with no lumps.

EXTENSION WITH AGGREGATES

For deeper applications (plastic and flowable consistancy only), 25 lbs. of 3/8" (9.5 mm) coarse aggregate can be added.

The aggregate must be non-reactive (reference ASTM C-1260, C-227 and C-289), clean, well graded, saturated surface dry, have low absorption and high density, and comply with ASTM C-33 size number 8 per Table 2.

Variances in aggregate may result in different strengths.

Add pea gravel after the water and SikaGrout®-212.▪

APPLICATION

Within 15 minutes after mixing, place grout into forms in normal manner to avoid air entrapment.

Vibrate, pump, or ram grout as necessary to achieve flow or compaction. SikaGrout®-212 must be confined in either the horizontal or vertical direction leaving minimum exposed surface.

SikaGrout®-212 is an excellent grout for pumping, even at high flow.

For pump recommendations, contact Technical ▪

Service.

After grout has achieved final set, remove forms, trim or shape exposed grout shoulders to designed profile.

CURING TREATMENT

Wet cure for a minimum of 3 days or apply a curing compound which complies with ASTM C-309 on exposed surfaces.

CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use.

LIMITATIONS

Not to be used as an overlay in unconfined spaces▪ Not to be used as a patch repair▪ Avoid application in direct sun and/or strong wind▪ Apply only to sound, prepared substrate▪ Do not add additional water after application as this may cause cracking

Protect freshly applied material from freezing and frost▪ Keep exposed surfaces to a minimum▪ As with all cement based materials, avoid contact with aluminum to prevent adverse chemical reaction and possible product failure. Insulate potential areas of contact by coating aluminum bars, rails, posts etc. with an appropriate epoxy such as Sikadur® Hi-Mod 32.

BASIS OF PRODUCT DATA

Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions.

OTHER RESTRICTIONS

See Legal Disclaimer.

ENVIRONMENTAL, HEALTH AND SAFETY

For further information and advice regarding transportation, handling, storage and disposal of chemical products, user should refer to the actual Safety Data Sheets containing physical, environmental, toxicological and other safety related data. User must read the current actual Safety Data Sheets before using any products. In case of an emergency, call CHEMTREC at 1-800-424-9300, International 703-527-3887.

DIRECTIVE 2004/42/CE - LIMITATION OF EMISSIONS OF

VOC

0 g/L (EPA Method 24)

LEGAL DISCLAIMER

• KEEP CONTAINER TIGHTLY CLOSED

Product Data Sheet SikaGrout®-212 August 2018, Version 01.02

3 / 4

• KEEP OUT OF REACH OF CHILDREN

• NOT FOR INTERNAL CONSUMPTION

• FOR INDUSTRIAL USE ONLY

• FOR PROFESSIONAL USE ONLY

Prior to each use of any product of Sika Corporation, its subsidiaries or affiliates (“SIKA”), the user must always read and follow the warnings and instructions on the product’s most current product label, Product Data Sheet and Safety Data Sheet which are available at usa.sika.com or by calling SIKA’s Technical Service Department at 1-800-933-7452. Nothing contained in any SIKA literature or materials relieves the user of the obligation to read and follow the warnings and instructions for each SIKA product as set forth in the current product label, Product Data Sheet and Safety Data Sheet prior to use of the SIKA product.

SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties on the current Product Data Sheet if used as directed within the product’s shelf life. User determines suitability of product for intended use and assumes all risks. User’s and/or buyer’s sole remedy shall be limited to the purchase price or replacement of this product exclusive of any labor costs.

NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL

APPLY INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL

THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.

SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS

PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT

OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD

BY OTHERS.

Sale of SIKA products are subject to the Terms and Conditions of Sale which are available at https://usa.sika.com/en/group/SikaCorp/termsandconditions.html or by calling 1-800-933-7452.

Sika Corporation 201 Polito Avenue Lyndhurst, NJ 07071 Phone: +1-800-933-7452 Fax: +1-201-933-6225 usa.sika.com

Sika Mexicana S.A. de C.V.

Carretera Libre Celaya Km. 8.5 Fracc. Industrial Balvanera Corregidora, Queretaro C.P. 76920 Phone: 52 442 2385800 Fax: 52 442 2250537

SikaGrout-212-en-US-(08-2018)-1-2.pdf

Product Data Sheet SikaGrout®-212 August 2018, Version 01.02

4 / 4

TECHNICAL DATA

North America: cetco@mineralstech.com | www.cetco.com

WATERSTOP-RX®

EXPANDING CONCRETE JOINT WATERSTOP

DESCRIPTION

WATERSTOP-RX is a hydrophilic strip wa-terstop designed to stop water infiltration through cast-in-place concrete construction joints by expanding upon contact with water to form a positive seal against the concrete.

The key to WATERSTOP-RX’s effectiveness is its superior expansion to seal and fill voids and cracks in the concrete. WATERSTOP-RX is an active bentonite/butyl-rubber based waterstop that is designed to replace pas-sive PVC/Rubber dumbbell waterstops, thereby eliminating the requirement of spe-cial pieces, split-forming and seam welding.

WATERSTOP-RX has been successfully tested by independent testing firms to over 60 me-ters (200 feet) of hydrostatic water pressure, under both continuous immersion and wet/ dry cycling.

WATERSTOP-RX is available in three sizes and shapes (see Product Table). WA- TERSTOP-RX 101 is produced in a rect-angular shape measuring 25 x 20 mm (1” x 3/4”). WATERSTOP-RX 101T is produced in a trapezoidal shape measuring 31 x 12 mm (1-1/4” x 1/2”) with a reinforcing plastic scrim embedded in the top surface for high tensile strength. The patented trapezoidal shape distributes the expansive force over a greater area and allows the concrete to flow more readily over the product during place-ment. WATERSTOP-RX 102 is produced in a half-circle (Crescent) shape measuring 19 x 9 mm (3/4” x 3/8”).

Though WATERSTOP-RX possesses good resistance to many chemicals, the waterstop is not intended to be used as the primary joint sealant for chemical containment ves-sels. Consult manufacturer for guidance re-garding chemical compatibility for secondary chemical containment applications. Addition-ally, WATERSTOP-RX is not an expansion joint sealant; contact CETCO for expansion joint applications.

APPLICATIONS

Applications include both vertical and hori-zontal non-moving concrete construction joints, new to existing concrete construction, irregular surfaces, and around through-wall penetrations, such as plumbing and utility pipes. Additionally WATERSTOP-RX can seal around concrete pilings and steel H-piles passing through the slab. WATERSTOP-RX works in both continuous hydrostatic and in-termittent hydrostatic conditions.

WATERSTOP-RX products are designed for reinforced structural concrete with a mini-mum of 20N/mm2 (3,000 psi) compressive strength. RX-101 and RX-101T are designed for concrete 200 mm (8”) thick or greater with two rows of reinforcing steel. RX-102 is designed for vertical concrete 150 mm (6”) thick or greater; and horizontal concrete no less than 100 mm (4”) thick. RX-102 should be used in concrete with one row of steel reinforcement, concrete curbs, planter walls, fountains, and lightweight structural concrete.

WATERSTOP-RX is a reliable, cost-effective means to stop water infiltration through con-crete cold joints. It can also be used around pipe and structural penetrations

INSTALLATION

Surface preparation: Surfaces should be clean and dry. Remove all dirt, rocks, rust or other construction debris. Do not install WA- TERSTOP-RX in standing water or on an iced substrate.

Adhesive: Apply a continuous bead of CET- SEAL along the substrate where WATERSTOP- RX will be installed. Assure proper 75 mm (3”) concrete coverage will be maintained. Keep the nozzle tip pressed against the concrete at a 45o angle during application.

Installation: After applying a continuous bead of CETSEAL, remove release paper, then firm-ly press the entire length of WATERSTOP-RX onto the adhesive. For vertical and overhead applications, firmly press a minimum of 15 seconds to assure adhesion. For best results apply WATERSTOP-RX within 15 minutes of adhesive installation. WATERSTOP-RX must be placed into adhesive prior to CETSEAL skinning over and curing. CETSEAL may be applied to damp surfaces, but not in stand-ing water.

Tightly butt coil ends together to form a con-tinuous waterstop - do not overlap coil ends.

Place in maximum practical lengths to mini-mize coil end joints. Where required, cut coils with a sharp knife or utility blade to fit coil ends together. Make horizontal to vertical transitions by abutting product coil sections together, no special accessory pieces are re-quired.

At structural and pipe penetrations, cut into strips to fit around the penetration. Apply to adhesive and abut coil ends together.

On irregular surfaces such as stone or rough concrete, make sure WATERSTOP-RX remains in direct contact with the substrate along the entire installation. There should not be any air gap between the WATERSTOP-RX and the substrate.

General Application Detail

75 mm (3”)

Footing/Wall Joint

Place WATERSTOP-RX inside of outer most reinforcing dowels

Minimum 75 mm (3”) to exterior surface of wall

WATERSTOP-RX

FORM: TDS_Bentogrout_AM_201308_V1

WATERSTOP-RX®

EXPANDING CONCRETE JOINT WATERSTOP

Installation with REVO-FIX: REVO-FIX is a steel mesh used to mechanically secure WATERSTOP-RX 101 into position using the accompanying supplied fasteners. Remove release paper and place the WATERSTOP-RX on the concrete substrate. Then place REVO- FIX strips over the WATERSTOP-RX, lapping the strip ends by 25 mm (1”) maximum. Nail through LAP with fastener supplied, and install one fastener 300 mm (12”) on center along the REVO-FIX.

End-to-end or end-to-side REVO-FIX junctions are created by simple butt joints pressed firm-ly together. Start at junctions; do not stretch WATERSTOP-RX to fit. Do not overlap water-stop.

LIMITATIONS

WATERSTOP-RX is not a self-adhering product.

CETSEAL or REVO-FIX is required to secure WATERSTOP-RX to concrete, metal, or PVC (Pipe) surfaces. Mechanical fasteners should be used with REVO-FIX to secure WATERSTOP- RX 101; and fasteners can be used in con-junction with CETSEAL. Mechanical fasteners should not be used to secure WATERSTOP-RX alone. Do not use any other adhesive or con-struction sealant, except CETSEAL, to secure

WATERSTOP-RX.

WATERSTOP-RX is not designed, nor intended to function as an expansion joint sealant. For precast concrete applications, contact manu-facturer for product suitability and for any spe-cial installation requirements.

WATERSTOP-RX products are designed for structural concrete with a minimum of 20N/ mm2 3,000 psi compressive strength. WA- TERSTOP-RX 101 and RX-101T require a minimum of 3” (75 mm) of concrete coverage.

WATERSTOP-RX 102 requires a minimum con-crete coverage of 2” (50 mm). WATERSTOP-RX should only be used in applications where the product is completely encapsulated within the concrete.

WATERSTOP-RX should not be prehydrated by being subjected to submersion or remain in extended contact with water prior to encap-sulation in concrete. If the product exhibits considerable swell prior to encapsulation in the concrete, it must be replaced with new material.

In conditions where severe ground water chemical contamination exists, or is expected, consult manufacturer for product chemical compatibility information.

PACKAGING

RX-101: 30 m (100 ft./box) RX-101T: 36 m (120 ft./box) RX-102: 60 m (200 ft./box) CETSEAL and REVO-FIX are packaged sepa-rately.

ACCESSORY PRODUCTS

CETSEAL is a multi-purpose, single compo-nent polyether moisture cure adhesive used to secure WATERSTOP-RX into position. Apply a continuous bead of CETSEAL to substrate then install WATERSTOP-RX before CETSEAL skins over and cures. Adhesive yield will vary with use, substrate and application.

WATERSTOP-RX PRODUCT TABLE

PRODUCT SIZE ROLL

LENGTH

CROSS-SECTION SHAPE UNIT QTY/CARTON MIN CONCRETE

COVERAGE

RX-101 25 x 20 mm (1” X 3/4”) 5 m (16’ 8”) Rectangle 30 m (100 LF) 75 mm (3”) RX-101T 31 x 12 mm (1-1/4” X 1/2”) 6 m (20’) Trapezoid with Poly Scrim

Reinforcement 36 m (120 LF) 75 mm (3”)

RX-102 19 x 9 mm (3/4” x 3/8”) 10 m (33’ 4”) Half-Circle 60 m (200 LF) 50 mm (2”)

STEP 1

CLEAN SURFACE

STEP 2

APPLY

ADHESIVE

STEP 3

PLACE

WATERSTOP

STEP 4

BUTT COIL ENDS

STEP 5

POUR

CONCRETE

REMOVE ALL DIRT AND DEBRIS

APPLY CETSEAL

REMOVE RELEASE PAPER THEN PRESS

FIRMLY AGAINST CETSEAL. MAINTAIN

MIN. CONCRETE COVERAGE DEPTH

TIGHTLY BUTT COIL ENDS TO FORM A

CONTINUOUS WATERSTOP. DO NOT

OVERLAP COIL ENDS

Concrete

WATERSTOP-RX

Minimum 75 mm (3”)

LIMITED WARRANTY

Specifications and other information contained herein supersedes all previously printed matter and are subject to change without notice.

All goods sold by seller are warranted to be free from defects in mate-rial and workmanship. The foregoing warranty is in lieu of and excludes all other warranties not expressly set forth herein, whether expressed or implied by operation of law or otherwise, including but not limited to any…