1696746_DWG_5of5.pdf

GENERAL NOTES

INSTALLATION SHALL COMPLY WITH UFC 3-600-01, UFC 1-200-01, UFC 4-010-06, 2023 NATIONAL ELECTRICAL CODE, NFPA 72, NFPA 1, NFPA 101, NFPA 1225, UL 2525, IBC, ABA, ADA, EQUIPMENT MANUFACTURER'S REQUIREMENTS AND NECA STANDARDS OF

INSTALLATION.

ALL CONDUCTORS INSTALLED IN EXTERIOR SPACES SHALL BE XHHW, INTERIOR WIRING MAY BE

THHW/THHN. UNLESS OTHERWISE NOTED

CONTRACTORS SHALL PROVIDE AND INSTALL AN EQUIPMENT GROUNDING CONDUCTOR IN ALL NEW

CONDUITS.

ALL CONDUCTOR SIZES SHOWN ARE BASED ON COPPER.

ALL EQUIPMENT AND MATERIALS ARE UL LISTED WHERE LISTING IS AVAILABLE FOR THAT TYPE OF

EQUIPMENT OR CONFORM TO ANSI OR NEMA STANDARDS

WORKMANSHIPS SHALL CONFORM TO CONSTRUCTION PRACTICES RECOMMENDED BY THE AMERICAN

ELECTRICIANS HANDBOOK BY CROFT (LATEST EDITION) AND WILL BE SUBJECTED TO THE APPROVAL

OF THE AGENCY THAT HAS JURISDICTION AND THE ENGINEER OF THE RECORD.

ALL METALLIC ENCLOSURES, RACEWAYS, AND ELECTRICAL EQUIPMENT SHALL BE GROUNDED IN

ACCORDANCE WITH THE REQUIREMENTS OF THE NEC ARTICLE 250, WITH THE GROUND WIRE IN EVERY RACEWAY.

RACEWAY SHALL BE SIZED IN ACCORDANCE WITH THE NEC TABLE 250-122.

TEST COMPLETED INSTALLATION AND CORRECT ALL DEFICIENCIES FOUND IN THE SYSTEM OR INSTALLATION.

ELECTRICAL DRAWINGS ARE DIAGRAMMATIC AND DO NOT SHOW ALL CONDUIT AND CONNECTIONS

BETWEEN RESPECTIVE DEVICES, FIXTURES, AND EQUIPMENT. CONTRACTOR HAS TO DETERMINE

EXACT ROUTING OF CONDUIT CONNECTIONS AND BETWEEN RESPECTIVE DEVICES, FIXTURES, AND

EQUIPMENT. REFER TO ARCHITECTURAL PLANS FOR EXACT LOCATIONS.

CONDUIT TO BE EMT UNLESS OTHERWISE NOTED. PROVIDE JUNCTION BOXES AS REQUIRED BY CODE.

PAINT EXPOSED CONDUIT, BOXES, AND SUPPORTS TO MATCH ADJACENT SURFACES.

PROVIDE SEPARATE NEUTRAL CONDUCTOR FOR ALL 120VAC CIRCUITS.

COORDINATE LOCATION OF ALL TWO WAY COMMUNICATIONS EQUIPMENT AND SIGNAGE WITH ARCHITECT PRIOR TO

START OF WORK.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

TWO WAY COMMUNICATIONS SYMBOL LIST

TWO WAY COMMUNICATIONS SYSTEM

ABBREVIATIONS

SYMBOL

A101

SIM

AF

C

CLF

CP

DP

DSN

DW

EL

EWC

GFI

HA

I

IG

L

LC

LB

MDP

MW

NL

PFB

R

REF

S

T

TR

WP

4X

ARC FAULT BREAKER

CONDUIT

CURRENT LIMITING FUSE

COPIER

DISPOSAL

DEFENSE SWITCHED NETWORK

DISHWASHER

EVENING LIGHT, TIMESWITCH CONTROLLED

ELECTRONIC WATER COOLER

GROUND FAULT CIRCUIT INTERRUPTER

HACR BREAKER

INSTRUCTIONAL

INSULATED GROUND CIRCUIT(S)

LIGHT(S)

LIGHTING CONTACTOR

LOCKABLE BREAKER

MAIN DISTRIBUTION PANEL

MICROWAVE

NIGHT LIGHT, TIMESWITCH CONTROLLED

PROVISIONS FOR BREAKER

RECEPTACLE(S)

REFRIGERATOR

SPARE BREAKER

TACTILE

TAMPER RESISTANT

WEATHERPROOF

NEMA 4X STAINLESS STEEL

VIEW REFERENCE

NORTH ARROW

CENTERLINE

NOTE REFERENCE

KEYNOTE REFERENCE

LUMINAIRE DESIGNATION,

REFER TO LUMINAIRE SCHEDULEABC

TWO WAY COMMUNICATIONS EMERGENCY CALL STATION, WALL MTD

TWO WAY COMMUNICATIONS MASTER STATION, WALL MTD

TWO WAY COMMUNICATIONS UPS, WALL MOUNTED IN CABINET

TWO WAY COMMUNICATIONS TWO WAY COMMUNICATION CONTROLLER,

WALL MOUNTED IN CABINET

TWO WAY COMMUNICATIONS INSTRUCTIONAL SIGN, WALL MOUNTED

TWO WAY COMMUNICATIONS ILLUMINATED SIGN WITH DIRECTIONAL

ARROWS AS INDICATED, WALL MOUNTED WITH BATTERY BACKUP

TWO WAY COMMUNICATIONS TACTILE SIGN, WALL MOUNTED

TWO WAY COMMUNICATIONS DIRECTIONAL SIGN, WALL MOUNTED

AR

AR

I

PS

MS

AR

T

AR

CM

I

H

IA

W

A

U

.S .A

LICENSED

PROFESSIONAL

ENGINEER

NO. 15212-E

J E

R E

MY B. D

O

W

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

M A

K A

L A

P A

H

A W

A

II

AS NOTED

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

/1

/2

:2 :1

P

M

C U s e rs \t d a o \D o c u m e n ts

\2

J -8

B a tt le

S ta ff T ra in in g

T

R n e w to m m y .d a o

.r v t

TT-001

JF

Y

P

R O

JE

C

T J

-8

G E

N E

R A

L N

O

TE

S , A

B B

R E

V

IA

TI

O

N S

S

Y M

B O

LS

L

E G

E N

D

JD

17322318

JH LS

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

F

IN

E G

A Y

A N

, G U

A M

M A

R

IN

E C

O R

P S

B A

S E

, C A

M P

B

LA

Z

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T T

-0

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

N62742-20-D-0001

03/ /2026

M S

PS

A R

A R

T A

R I

J

G

A

B

C

E

D

F

1 2 3 4 5 6 7 8 9

TA - HQ CAMP COMMANDANT

NURSING RM

TA - G3 FIRES

SVTC CONF RM / SIPR CAFE

GTR 1T (TRAINING TELECOM RM)

TRAINING MATERIAL STORAGE

STAIR 1A

S1A

TA - G4 LOGISTICS

MECHANICAL ENCLOSURE

ELEC RM

STAIR 1B

S1B

STAIR 1C

S1C

INTERIOR COC TRAINING PAD

EMERGENCY GENERATOR

BREAK RM

LOBBY 1

L1

ELEV 1

E1

GTR-1

TA - COC WATCH FLOOR

TA - G5 PLANS

ENTR VESTIBULE

MEN

JAN

CTR 1

CORRIDOR 1C

C1C

TA - G3 STRIKE CELL

110A

OFFICE

125A

TA - G3 OPS

105B

CORRIDOR 1A

C1A

WOMEN

CORRIDOR 1E

C1E

OFFICE

127A

TA - G2 COLLECTIONS AND ANALYSIS

108B

TA - G2 COLLECTIONS AND ANALYSIS

108A

TWO WAY

COMMUNICATION

MASTER STATION

CM

TWO WAY COMMUNICATION HEAD END EQUIPMENT. MAINTAIN

4'-0" FRONT CLEARANCE FROM FACE OF EQUIPMENT.

COORDINATE EQUIPMENT LOCATION WITH ELEC DWGS.

152mm SQ X 102mm D J-BOX WITH CAT 6 JACK AND OUTLET BOX. PROVIDE 27mm C, WITH CAT 6 TO NEAREST TR ROOM AND TERMINATE ON SPARE PATCH PANEL

PORT. COORDINATE PORT ASSIGNMENT WITH IT SYSTEM INSTALLER. PROVIDE

TELEPHONE LINE CONNECTION FOR TWO WAY COMMUNICATION SYSTEM.

PROVIDE 27mm C NIPPLE TO TWO WAY COMMUNICATION SUPERVISOR MODULE.

CAT 6 PATCH CABLE SHALL BE PROVIDED BY THE TWO WAY COMMUNICATION

INSTALLER. PROVIDE ID LABEL FOR CAT 6 JACK PER CAMPUS LABELLING SCHEME.

OFFICE

126B

OFFICE

126A

OFFICE

128B

OFFICE

128A

OFFICE

127B

TA - G1 OPERATIONS

128 TA - COMMAND DECK

TELECOM CLOSET

126C

AV CLOSET

126D

TA - MEDICAL CELL

MECH RM

ELEV MACHINE RM

TA - G3 STRIKE CELL

110B

CORRIDOR 1C

C1C

VESTIBULE 1C

V1C

ELEC CLOSET

CORRIDOR C1A NOT RAF

C1A NOT RAF

TA - G3 OPS

105A

TA - G7 COMM STAT

CORRIDOR 1B

C1B

ENTRY CONTROL POINT

102A

UTILITY CHASE

122A

I

H

IA

W

A

U

.S .A

LICENSED

PROFESSIONAL

ENGINEER

NO. 15212-E

J E

R E

MY B. D

O

W

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

M A

K A

L A

P A

H

A W

A

II

AS NOTED

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

/1

/2

:2 :1

P

M

C U s e rs \t d a o \D o c u m e n ts

\2

J -8

B a tt le

S ta ff T ra in in g

T

R n e w to m m y .d a o

.r v t

TT-101

JF

Y

P

R O

JE

C

T J

-8

1S T

F

LO

O R

T W

O -W

A Y

C O

M M

U N

IC

A

TI

O

N P

LA

N

JD

17322319

JH LS

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

F

IN

E G

A Y

A N

, G U

A M

M A

R

IN

E C

O R

P S

B A

S E

, C A

M P

B

LA

Z

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T T

-1

3/32" = 1'-0"1

1ST FLOOR TWO-WAY COMMUNICATION PLAN

2' 8' 32'0 4' 6' 24'16' 3/32" =1'-0"

PLAN

NORTH

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

AR

I

AR

T

AR

G

A

B

C

E

D

F

1 2 3 4 5 6 7 8 9

TWO WAY COMMUNICATION

CALL BOX

PRINT RM

ELEC CLOSET

TECH - ADMIN CELL AND LOGISTICS SECTION

TRAINING MATERIAL STORAGE

TRAINING MATERIAL STORAGE

TECG OFFICE / CONF RM

STAIR 2C

S2C

STAIR 2B

S2B

CTR

STORAGE

BREAK RM

TA - TECHCON

208A

JFACC / AVIATION OPS CENTER

227B

SIM TECH CONTROL JLVC / MCVP

OFFICE

211F

TA - G6 PRIMARY

ELEV 2A

EL

SVTC CONF RM / SIPR CAFE

JAN

WOMEN

MECH RM

GTR-2

GTR-2T (TRAINING/TELECOMM RM)

LOBBY 2

L2

OPPOSING FORCES CONTROL CELL

206B

MEN

TA - G9 EXPERIMENTATION

INTEL CONTROL CELL

205B

ELEC CLOSET

CONF RM

211A

OFFICE

211B

OFFICE

211C

OFFICE

211D

OFFICE

211E

STAIR 2A

S2A

VESTIBULE 2

V2

UTILITY CHASE

220A

TECG INTEL SECTION AND RED CELL

225B

HHQ RESPONSE CELL

BLUE / GREEN FORCES CONTROL CELL

226A

I

H

IA

W

A

U

.S .A

LICENSED

PROFESSIONAL

ENGINEER

NO. 15212-E

J E

R E

MY B. D

O

W

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

M A

K A

L A

P A

H

A W

A

II

AS NOTED

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

/1

/2

:2 :2

P

M

C U s e rs \t d a o \D o c u m e n ts

\2

J -8

B a tt le

S ta ff T ra in in g

T

R n e w to m m y .d a o

.r v t

TT-102

JF

Y

P

R O

JE

C

T J

-8

2N D

F

LO

O R

T W

O -W

A Y

C O

M M

U N

IC

A

TI

O

N P

LA

N

JD

17322320

JH LS

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

F

IN

E G

A Y

A N

, G U

A M

M A

R

IN

E C

O R

P S

B A

S E

, C A

M P

B

LA

Z

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T T

-1

3/32" = 1'-0"1

2ND FLOOR TWO-WAY COMMUNICATION PLAN

2' 8' 32'0 4' 6' 24'16' 3/32" =1'-0"

PLAN

NORTH

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P

HELP PHONE

SOLID LIGHT:

BLINKING LIGHT:

CALLING

RECEIVED

EMERGENCY PHONE

Phone 1

Phone 2

Phone 3

Phone 4

Phone 5

Battery:

Green: Full Charge

Yellow: Mid-level Charge

Red: Low Charge

Battery

AC Power

Submaster 1

Submaster 2

Rescue Services Disconnect Call to Rescue Services

MASTER STATION

18 AWG 4 CONDUCTOR TWO

PAIR CABLE

UPS WITH BATTERIES

120VAC UPS OUTPUT

POWER. POWER CHORD

CONNECTION.

(CALL BOX) ELEV LOBBY 2

ENTRY VESTIBULE 101

NOTES:

1. ALL WIRING SHALL BE IN METALLIC CONDUIT, 27mm: MINIMUM TRADE SIZE.

2. PROVIDE DEDICATED 120V, 20A CIRCUIT FOR POWER SUPPLY. REFER TO ELECTRICAL DRAWINGS FOR CIRCUIT INFORMATION.

3. ALL COMMUNICATION WIRING SHALL BE 2 HOUR FIRE RATED AND SHALL HAVE A PATHWAY SURVIVABILITY OF 2 HOURS.

4. PROVIDE ALL WIRING PER THE TWO WAY COMMUNICATION SUPPLIER SHOP DRAWINGS.

5. PROVIDE ALL REQUIRED EQUIPMENT MOUNTING HARDWARE PER THE TWO WAY COMMUNICATION SUPPLIER SHOP DRAWINGS.

6. THE UPS SYSTEM FOR THE TWO-WAY EMERGENCY COMMUNICATIONS SYSTEMS SHALL BE CAPABLE OF OPERATING THE SYSTEM

UNDER QUIESCENT LOAD FOR A MINIMUM OF 24 HOURS AND THEN SUBSEQUENTLY DURING A FIRE OR OTHER EMERGENCY

CONDITION FOR A PERIOD OF 4 HOURS WITH ALL REMOTE CALL STATIONS ACTIVATED AND ALL MASTER CONTROL STATIONS

ANNUNCIATING THE CALLS.

7. FAILURE OF EITHER THE PRIMARY OR SECONDARY POWER SUPPLY SHALL RESULT IN A TROUBLE SIGNAL SENT TO THE FIRE

ALARM CONTROL PANEL.

8. PROVIDE STANDARD 483MM WALL MOUNT CABINET FOR TWO WAY SYSTEM CONTROLLER, AND UPS/BATTERIES. CABINET SHALL

BE LOCKABLE WITH SWINGING HINGED DOOR, REAR ACCESS TYPE HINGED, AND COOLING FANS. CABINET SIZE SHALL BE PER

TWO WAY COMMUNICATION SYSTEM SUPPLIER REQUIREMENTS.

120VAC, 50/60 HZ

UPS INPUT POWER PROVIDE

HARDWIRED CONNECTION

DSN PHONE LINE/EXTENSION REQUIREMENTS:

(1) MINIMUM OF 24V, 20 Ma OFF-HOOK (NO CURRENT IS DRAWN ON-HOOK).

(2) DSN PHONE LINE/EXTENSION SHOULD PROVIDE EITHER A DISCONNECT PULSE

(VOLTAGE DROP AT END OF CALL) OR 30-SECONDS OF SILENCE AFTER HANG-UP

(NO RE-ORDER OR HOWLER FEATURE).

(3) THERE MUST BE NO SPECIAL FEATURES (E.G., HOOK FLASH, CALL WAITING,

AUTO-REDIAL WHEN BUSY, VOICEMAIL, ETC.). THE DSN PHONE LINE/EXTENSION

MUST BE FEATURE FREE.

(4) IF THE PHONE LINE DOES NOT PROVIDE A CALLING PARTY DISCONNECT SIGNAL

(CPC), PROVIDE A SEPARATE CPC DISCONNECT DEVICE IN THE PHONE LINE TO

OBTAIN THE SIGNAL. THE DEVICE SHALL BE POWERED OFF THE PHONE LINE.

THE CPC DISCONNECT TIME SHALL BE 1 SECOND NOMINAL.

(5) PROVIDE A DEDICATED DSN LINE TO THE TWO WAY COMMUNICATION HEAD END

EQUIPMENT AND PROGRAM THE MASTER STATION TO AUTOMATICALLY

CONNECT WITH THE LOCAL BASE 911 DISPATCH AND VICE VERSA. THE BASE

SHALL INSTALL THE DSN LINE TO THE SCHOOL AND THE ELECTRICAL

CONTRACTOR SHALL RUN THE LINE FROM THE COMMS ROOM TO THE MASTER

STATION.

12 AWG 4 CONDUCTOR,

TWO PAIR CABLE

TWO-WAY

SYSTEM

CONTROLLER

UPS MONITOR ADDRESSABLE

FIRE ALARM

MONITOR

MODULE

(SEE FIRE

ALARM DWGS)

TO FIRE ALARM

CONTROL PANEL

POWER FAILURE

RELAY OUTPUT

ELEC 120

ELEC 120

1ST FLOOR

2ND FLOOR

27mmC, W/ CAT 6

DEDICATED DSN TELEPHONE LINE

SYSTEM FAULT. POWER

SUPPLY FAULT, BATTERY

FAULT

27mmC, W/ CAT 6 PATCH CABLE

152MM SQ. X 102MM D DEMARC J-BOX.

PROVIDE WITH CAT 6 JACK AND OUTLET BOX

J

3"

7.5"

14"

CONNECT TO NEAREST 120VAC

OR 277VAC EXIT SIGN CIRCUIT.

PROVIDE DOUBLE FACE SIGN

AND CHEVRONS AS REQUIRED.

3"

EMERGENCY

COMMUNICATIONS

EMERGENCY

COMMUNICATIONS

ILLUMINATED

SIGNAGE

ABOVE 60" BUT

BELOW 80" FROM

FLOOR TO TOP OF

SIGN COORDINATE

EXACT MOUNTING

HEIGHT WITH

ARCHITECT

TWO WAY COMMUNICATIONS

MASTER STATION

TACTILE

SIGNAGE

EMERGENCY

COMMUNICATIONS

INSTRUCTIONAL

SIGNAGE

48" - 60" FROM

FLOOR TO

LOWEST TACTILE

CHARACTER

60" FROM

FLOOR TO

CENTER

ABOVE OR

ADJACENT

TO EACH

CALL BOX

PUSH FOR HELP

PERSONS ABLE TO USE THE

EXIT STAIRWAY DO SO AS

SOON AS POSSIBLE, UNLESS

THEY ARE ASSISTING OTHERS.

LOCATION FLOOR

AFTER ACTIVATING THE TWO-

WAY EMERGENCY

COMMUNICATION SYSTEM,

WAIT HERE FOR ASSISTANCE.

CALL

BOX

48" FROM

FLOOR TO

PUSH

BUTTON

EMERGENCY

EVACUATION

ASSISTANCE

FINISHED FLOOR

EMERGENCY PHONE

DIRECTIONAL

SIGNAGE

48" - 60" FROM

FLOOR TO

LOWEST TACTILE

CHARACTER

EMERGENCY

COMMUNICATION

I

H

IA

W

A

U

.S .A

LICENSED

PROFESSIONAL

ENGINEER

NO. 15212-E

J E

R E

MY B. D

O

W

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

M A

K A

L A

P A

H

A W

A

II

AS NOTED

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

/1

/2

:2 :2

P

M

C U s e rs \t d a o \D o c u m e n ts

\2

J -8

B a tt le

S ta ff T ra in in g

T

R n e w to m m y .d a o

.r v t

TT-501

JF

Y

P

R O

JE

C

T J

-8

TW

O

W A

Y C

O M

M U

N

IC

A

TI

O N

S D

E

TA

IL

S

D

IA

G

R A

M

JD

17322321

JH LS

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

F

IN

E G

A Y

A N

, G U

A M

M A

R

IN

E C

O R

P S

B A

S E

, C A

M P

B

LA

Z

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T T

-5

NTSC1

TWO WAY COMMUNICATIONS

ILLUMINATED SIGN DETAIL

NTSA1

TWO WAY COMMUNICATIONS DIAGRAM

NTSC3

TWO WAY COMMUNICATIONS MOUNTING

HEIGHT DETAIL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P

SYSTEM INPUTS

SYSTEM OUTPUTS

A B C D

A C

TIV

A

TE V

IS

U

AL

ALE

R T A

T M

ASTER

S

TA

TIO

N S

O

LI

D L

IT

L

ED

IN

D

IC

ATE Z

O N E O

F C

ALL

B O X A

T M

ASTER

S

TATIO

N

A C

TIV

ATES V

IS

U

AL

A

LE

R T A

T M

ASTER

S

TATIO

N S

LO

W

B

LI

N

KIN

G

2-WAY SYSTEM COMMUNICATION FAILURE

A C

TIV

ATES

A

U D

IO

IN

D

IC

A

TO

R A

T M

ASTER

S

TATIO

N

A C

TIV

ATES V

IS

U A L

IN

D

IC

ATO

R A

T M

ASTER

S

TA

TIO

N

TR

AN

SM

IT

S U P

ER

VIS

O R Y S

IG

N

AL

TO

M

O N

IT

O R

IN

G S

TATIO

N

TR

AN

S M

IT

T

R O U B

LE

S

IG

N

AL

TO

M

O N

IT

O R

IN

G S

TA

TIO

N

E F G

2 2-WAY SYSTEM BATTERY FAILURE

E M

E R G

EN

C Y C

ALL

IN

P R O G R

ESS

LE

D

C A

LL

O N H

O

LD

3 2-WAY SYSTEM LOW BATTERY

4 AC POWER LOSS

5 DC POWER LOSS

6 2-WAY SYSTEM COMMON TROUBLE

7 2-WAY SYSTEM WIRE/LINE SUPERVISION

8 CALL BOX INITIATION

9 CALL BOX ON HOLD

10 CALL BOX IN PROGRESS

OUTSIDE PHONE LINE FAILURE

MASTER STATION FAILURE

CALL BOX FAILURE

LINE FAULT MONITOR

TR

AN

SM

IT

T R O U

BLE

S

IG

N

AL

TO

F

IR

E A

LA

R M

C O N

TR

O L

PA

N

EL

H

I

H

IA

W

A

U

.S .A

LICENSED

PROFESSIONAL

ENGINEER

NO. 15212-E

J E

R E

MY B. D

O

W

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

M A

K A

L A

P A

H

A W

A

II

AS NOTED

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

/1

/2

:2 :2

P

M

C U s e rs \t d a o \D o c u m e n ts

\2

J -8

B a tt le

S ta ff T ra in in g

T

R n e w to m m y .d a o

.r v t

TT-502

JF

Y

P

R O

JE

C

T J

-8

TW

O

W A

Y C

O M

M U

N

IC

A

TI

O N

S S

E Q

U E

N C

E O

F O

P E

R A

TI

O

N M

A

TR

IX

JD

17322322

JH LS

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

F

IN

E G

A Y

A N

, G U

A M

M A

R

IN

E C

O R

P S

B A

S E

, C A

M P

B

LA

Z

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T T

-5

NTSA1

TWO WAY COMMUNICATIONS SEQUENCE

OF OPERATION MATRIX

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

M

A K

A L A

P A

H

A W

A

II

AS NOTED

/1

/2

:1 :1

P

M

A u to d e s k D o c s /J

-8

B S

T F

/B L

D G

-J

-1

-T A

.r v t

TA001

JF

Y

P

R O

JE

C

T J

-8

A V

S Y

S

TE

M S

G E

N E

R A

L N

O

TE

S

PKD

17322326

PKD DHC

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

N62742-20-D-0001

M C

B C

A M

P B

LA

Z

, G U

A M

U .S

. N A

V S

U P

P A

C T

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T A

AV SYSTEMS GENERAL NOTES:

1. ADHERE TO GOVERNMENT RULES AND REGULATIONS, DIVISION 01, 11, 26, AND 27. SPECIFICATION

SECTIONS, AND DRAWINGS AND GENERAL PROVISIONS OF THE CONTRACT, INCLUDING GENERAL AND

SUPPLEMENTARY CONDITIONS AND DIVISION 01 SPECIFICATION SECTIONS.

2. THE DRAWINGS AND SPECIFICATIONS ARE COMPLEMENTARY AND WHAT IS CALLED FOR (OR SHOWN) IN EITHER MUST BE PROVIDED AS IF CALLED FOR IN BOTH. IN CASE OF CONFLICT BETWEEN THE DRAWINGS

AND SPECIFICATIONS, THE MORE STRINGENT REQUIREMENT WILL BE ENFORCED, UNLESS THE

CONTRACTOR REQUESTS AND RECEIVES WRITTEN CLARIFICATION STATING OTHERWISE.

3. COORDINATE THE SEQUENCE OF WORK AND REPORT DISCREPANCIES BETWEEN THESE CONTRACT

DRAWINGS AND ACTUAL FIELD CONDITIONS TO THE CONTRACTING OFFICER.

4. DEFINITIONS:

A. "FURNISH" MEANS TO "SUPPLY" AND USUALLY REFERS TO AN ITEM OF EQUIPMENT, CABLING, OR

HARDWARE.

B. "INSTALL" MEANS TO SET IN PLACE, CONNECT, PLACE IN FULL OPERATIONAL ORDER, AND PERFORM

REQUIRED VERIFICATION TESTING.

C. "PROVIDE" MEANS TO "FURNISH AND INSTALL."

D. "EQUIVALENT" MEANS "MEETS THE SPECIFICATIONS OF THE REFERENCE PRODUCT OR ITEM IN

SIGNIFICANT ASPECTS." SIGNIFICANT ASPECTS MUST BE DETERMINED BY THE CONTRACTING

OFFICER.

E. "WORK BY OTHER(S) (CONTRACTOR):" "RE: DIVISION XX," AND SIMILAR EXPRESSIONS MEANS WORK PERFORMED UNDER THE CONTRACT DOCUMENTS, BUT NOT NECESSARILY UNDER THE DIVISION OR

SECTION OF THE WORK ON WHICH THE NOTE APPEARS. IT IS THE CONTRACTOR’S SOLE

RESPONSIBILITY TO COORDINATE THE WORK OF THE CONTRACT BETWEEN THEIR SUPPLIERS,

SUBCONTRACTORS, AND EMPLOYEES. IF CLARIFICATION IS REQUIRED, CONSULT CONTRACTING

OFFICER BEFORE SUBMITTING BID.

5. PROVIDE PATHWAYS, RELATED HARDWARE, EQUIPMENT AND CABLING SHOWN ON THESE DRAWINGS

EXCEPT WHERE OTHERWISE NOTED.

6. DEDICATED PATHWAYS / RACEWAYS MUST BE PROVIDED TO FULLY SUPPORT SYSTEM CABLING FOR THE ENTIRE DISTANCE. NO CABLING IS PERMITTED TO BE RUN UNSUPPORTED OR LAID OVER CEILING TILES, ELECTRICAL CONDUITS, HVAC DUCTS, PIPING, OR OTHER SUPPORTS OR CEILING MEMBERS NOT INTENDED

FOR THAT PURPOSE.

7. COORDINATE WITH OTHER TRADES AND ADJUST AND ADAPT WORK FOR ACTUAL PROJECT CONDITIONS SO FINAL INSTALLATION IS COMPATIBLE WITH MATERIALS, EQUIPMENT, ROUTING, AND CLEARANCES OF

TRADES.

A. EXAMINE THE CONTRACT DOCUMENTS OF TRADES (DRAWINGS FOR THE ARCHITECTURAL,

REFLECTED CEILING, TELECOMMUNICATIONS, CIVIL, HEMP SHIELDING, MECHANICAL HVAC,

ELECTRICAL POWER AND LIGHTING, FIRE PROTECTION, PLUMBING, ETC.).

B. ASSIST OTHER CONTRACTORS IN PREPARING SHOP DRAWINGS FOR COORDINATING INSTALLATION

OF WORK (LOCATION, CEILING CLEARANCES, CABLE TRAY ACCESSIBILITY AND PATHWAY

CLEARANCES THROUGHOUT, ETC.).

C. REFER TO ARCHITECTURAL DRAWINGS TO DETERMINE MINIMUM CLEARANCE REQUIREMENTS FROM

FINISHED FLOOR TO BOTTOM OF DUCTWORK, CONDUIT, CABLE TRAY, LIGHTING, ETC.

8. MAINTAIN A RUNNING UPDATE OF FIELD OR CONTRACT DOCUMENT CHANGES AND UPDATE "AS-BUILT"

DRAWINGS AS AN ONGOING PROCESS.

9. PROVIDE PATHWAYS / RACEWAYS FOR THE AV CABLING. THIS INCLUDES, BUT IS NOT LIMITED TO, CONDUIT, SLEEVES, STUB-UPS, WIREWAYS, J-HOOK CABLE SUPPORT PATHS, AND PERMANENTLY INSTALLED

JUNCTION BOXES IN FLOORS, WALLS, CEILINGS AND UNDERGROUND.

10. PATHWAYS MUST BE BONDED TO THE TELECOM BONDING AND GROUNDING SYSTEM FOR CONNECTION TO THE BUILDING GROUNDING ELECTRODE SYSTEM IN ACCORDANCE WITH THE SPECIFICATIONS AND ANSI J- STD-607-D. PROVIDE GROUND CONDUCTORS, GROUND CLAMPS, COMPRESSION TAPS, LUGS AND ITEMS

REQUIRED FOR CONNECTION TO THE BONDING AND GROUNDING SYSTEM.

11. FOR WALL-MOUNTED AV DEVICES, PROVIDE RECESS-FLUSH MOUNTED BACKBOXES AND EXTENSION RINGS WITH TOTAL DEPTH TO MATCH THICKNESS OF COMPLETE WALL AND INSULATION ASSEMBLY. PROVIDE

CONDUITS AS INDICATED IN AV PATHWAY RISER DIAGRAMS.

12. REFER TO SYSTEM SPECIFIC DRAWINGS AND DETAILS FOR BACKBOX REQUIREMENTS SPECIFIC TO EACH TYPE. SELECT DEVICES MAY REQUIRE SPECIALIZED BACKBOX TYPES, SIZES, AND MOUNTING CONDITIONS

AS DEPICTED IN DRAWINGS.

13. CONDUITS FOR AV MUST BE SIZED AS INDICATED ON AV PATHWAY RISER DIAGRAMS.

14. CONDUITS FOR AV MUST BE OF NON-FLEXIBLE, RIGID-WALLED CONSTRUCTION, EXCEPT AS OTHERWISE

NOTED OR DETAILED ON THE DRAWINGS.

15. COORDINATE WITH CONTRACTING OFFICER AND OTHER TRADES PRIOR TO CONSTRUCTION FOR CONDUIT

AND BACKBOX LOCATIONS IN PRECAST WALLS, POURED CONCRETE, MASONRY, ETC.

16. OUTLET MOUNTING HEIGHTS INDICATED ARE TO CENTERLINE OF BOX UNLESS OTHERWISE NOTED.

17. DEVICES INDICATED TO BE INSTALLED AT DIFFERENT MOUNTING HEIGHTS AND LOCATED WITHIN ONE STUD

SPACE FROM EACH OTHER MUST ALIGN VERTICALLY ON THE SAME SIDE OF THE STUD.

18. PATHWAY MOUNTING HEIGHTS INDICATED ON PLANS ARE TO THE BOTTOM OF THE PATHWAY SUPPORTS

(STRUT CHANNEL TRAPEZE, ANGLE SUPPORT, CONDUIT CLAMP, ETC).

19. PROVIDE SEISMIC BRACING FOR PATHWAYS AND EQUIPMENT REQUIRED BY CODE, LOCAL GOVERNING

JURISDICTIONS, AND MANUFACTURERS’ SPECIFICATIONS.

20. AV PATHWAY SYSTEMS MUST BE DEDICATED FOR AV CABLING ONLY. OTHER SYSTEMS INCLUDING, BUT NOT LIMITED TO, FIRE ALARM, HVAC CONTROLS, LIGHTING CONTROLS, ETC. MUST BE SUPPORTED BY

OTHER MEANS AND MUST NOT BE ROUTED WITHIN THE AV PATHWAYS.

21. PROVIDE CONDUITS / SLEEVES THROUGH WALLS AND ACROSS INACCESSIBLE CEILING SPACES TO ENSURE

UNOBSTRUCTED PATHWAY BETWEEN END POINTS INDICATED ON AV PATHWAY RISER DIAGRAMS.

22. AV PATHWAYS ROUTED THROUGH ELECTRICAL ROOMS MUST BE PHYSICALLY CONTINUOUS.

23. PROVIDE NEMA 3R CORROSION RESISTANT OUTLETS, CONDUITS AND WIRING METHODS IN AREAS

EXPOSED TO WET CONDITIONS.

24. IN AREAS WHERE CORROSIVE CHEMICALS ARE PRESENT, PROVIDE NEMA 4X OR NEMA 12 FULLY- SEALED/GASKETED CORROSION-RESISTANT ENCLOSURES, OUTLET COVERS, CONDUITS AND WIRING

METHODS, CONSTRUCTED OF TYPE 316 STAINLESS STEEL, NO EXCEPTION.

25. INSTALL PATHWAYS PARALLEL OR PERPENDICULAR TO WALL OR STRUCTURAL MEMBERS TO FOLLOW STRUCTURAL SURFACE CONTOURS AND DO NOT OBSTRUCT PASSAGEWAYS. WHERE MULTIPLE RACEWAYS

ARE ROUTED THROUGH THE SAME AREA, GROUP SUCH RACEWAYS TOGETHER.

26. INSTALL CONDUIT WITH LARGE-RADIUS BENDS. THE RATIOS FOR MINIMUM BEND RADIUS TO CONDUIT

DIAMETER ARE:

A. 6:1 BEND RADIUS OF THE INSIDE CONDUIT DIAMETER FOR CONDUIT SIZES LESS THAN 2 IN.

B. 10:1 BEND RADIUS OF THE INSIDE CONDUIT DIAMETER FOR CONDUIT SIZES EQUAL TO OR GREATER

THAN 2 IN.

27. CONDUIT ROUTING MUST NOT EXCEED 180 DEG. FOR THE SUM OF ELBOWS, SWEEPS AND BENDS FOR A PARTICULAR CONDUIT RUN WITHOUT AN APPROVED PULL-BOX, HAND HOLE, OR VAULT. THE MAXIMUM BEND FOR ANY LOCATION MUST NOT EXCEED 90 DEG. 3-POINT SADDLE BENDS ARE NOT PERMITTED IN

CONDUIT ROUTES.

28. INSIDE CONDUIT RUNS MUST NOT EXCEED 100 FT BETWEEN PULL POINTS WITHOUT AN APPROVED PULL-

BOX.

29. PROVIDE PULL-BOXES AND HAND HOLES IN STRAIGHT SECTIONS OF CONDUIT ONLY. DO NOT USE PULL- BOXES OR HAND HOLES TO CHANGE PATHWAY DIRECTION, UNLESS SPECIFICALLY SHOWN WITH A CHANGE

IN DIRECTION ON THE DRAWINGS.

30. CONDUIT OUTLET BODIES (I.E., CONDULET, C, LB, LL, LR, T), MUST NOT BE USED AS CABLE PULL POINTS OR TO CHANGE PATHWAY DIRECTION IN ANY LOCATIONS. THESE DEVICES ARE COMMONLY USED FOR ELECTRICAL/POWER PATHWAYS AND ARE NOT APPROVED FOR LOW VOLTAGE CABLING. SPECIALTY "SMART LB" CONDUIT OUTLET BODIES DESIGNED FOR LARGE-BEND RADIUS CABLE ENTRY THROUGH EXTERIOR WALLS MAY BE PERMITTED ONLY WHEN SPECIFICALLY INDICATED ON PLANS OR PRE-APPROVED

IN WRITING BY THE CONTRACTING OFFICER.

31. PROVIDE PROTECTIVE INSULATED BUSHINGS ON CONDUIT ENDS INCLUDING RISER CONDUITS/SLEEVES, HORIZONTAL CONDUITS, DEVICE CONDUITS, AND SLEEVES.

32. STUB UP RISER CONDUIT A MINIMUM OF 6 IN. AFF.

33. PROVIDE CONDUIT QUANTITIES AND SIZES AS SHOWN. DO NOT COMBINE CONDUIT RUNS WITHOUT THE

WRITTEN PERMISSION OF THE CONTRACTING OFFICER.

34. PROVIDE LISTED EXPANSION FITTINGS IN CONDUIT OR RACEWAY CROSSING BUILDING EXPANSION JOINTS.

REFERENCE ARCHITECTURAL DRAWINGS FOR EXPANSION JOINT LOCATIONS.

35. PROVIDE EMPTY RACEWAY SYSTEMS WITH A PULL LINE OR TAPE INSTALLED WITH THREE FEET EXTENDING FROM EACH END, KNOTTED AND SECURED TO REMAIN IN PLACE. FOR INDOOR APPLICATIONS, USE PULL LINE HAVING NOT LESS THAN 200 LB. TENSILE STRENGTH. FOR OUTDOOR APPLICATIONS USE PULL TAPE

OR WIRE HAVING NOT LESS THAN 1200-LB. TENSILE STRENGTH.

36. SEAL PENETRATIONS THROUGH RATED ASSEMBLIES (WALLS, FLOORS, ETC.) AS INDICATED ON ARCHITECTURAL DRAWINGS TO MAINTAIN THE ASSEMBLY RATING AROUND AND WITHIN THE PATHWAY.

37. PROVIDE APPROVED REMOVABLE PILLOW-TYPE FIRESTOPPING SYSTEMS TO SEAL PENETRATIONS THROUGH RATED WALLS, FLOORS, ASSEMBLIES AND CONDUIT/SLEEVE OPENINGS FOR AV CABLING.

FIRESTOPPING SYSTEMS AND MATERIALS MUST BE RATED AND APPROVED FOR PREVENTION OF FLAMES, HOT GASSES AND SMOKE WHEN SUBJECTED TO THE REQUIREMENTS OF THE TEST STANDARD SPECIFIC

FOR APPLICABLE CODES AND AHJ REQUIREMENTS.

38. JUNCTION BOXES AND BACKBOXES FOR DATA, VOICE, VIDEO, POWER, OR OTHER UTILITIES MUST BE SEPARATED BY AT LEAST ONE STUD CAVITY WHEN SERVING OPPOSITE SIDES OF ACOUSTICALLY RATED PARTITIONS. ALL JUNCTION BOXES LOCATED WITHIN THE SAME STUD CAVITY MUST MAINTAIN A MINIMUM

OF 24 INCHES SEPARATION OR BE SEALED WITH PUTTY PADS.

39. DATA GIVEN ON THE DRAWINGS IS AS EXACT AS COULD BE SECURED. ABSOLUTE ACCURACY IS NOT

GUARANTEED. THE DRAWINGS ARE DIAGRAMMATICAL IN NATURE, AND SYMBOLS AND LINEWORK

CONTAINED THEREIN MUST NOT BE SCALED.

40. PATHWAY ROUTING ON THESE DRAWINGS PRIMARILY SHOWS INTERCONNECTIONS BETWEEN TERMINAL POINTS. COORDINATE THE EXACT ROUTING OF PATHWAYS BASED ON FIELD CONDITIONS PRIOR TO SUBMITTING SHOP DRAWINGS OR INITIATING WORK IN THE FIELD. SHOP DRAWINGS SHOWING ROUTING OF

THESE PATHWAYS MUST BE SUBMITTED AS SPECIFIED IN DIVISION 27 AND APPROVED BY THE

CONTRACTING OFFICER PRIOR TO INSTALLATION. EXTRA TIME MUST BE ALLOWED FOR THE

COORDINATION, SUBMITTAL REVIEW AND APPROVAL PROCESS.

41. ANY PROPOSED OR REQUIRED EXCEPTIONS TO THE AV PATHWAY ROUTING REQUIREMENTS IN THESE DRAWINGS AND ASSOCIATED SPECIFICATIONS MUST BE DETAILED IN CONTRACTOR SHOP DRAWINGS AND SUBMITTALS AND APPROVED PRIOR TO INSTALLATION. ANY REMEDIATION TO AV PATHWAY AND ROUTING TO MEET REQUIREMENTS WILL BE THE TOTAL RESPONSIBILITY OF THE CONTRACTOR AT NO ADDITIONAL

COST TO THE GOVERNMENT.

42. CONDUITS SMALLER THAN 2 IN. TRADE SIZE HAVE NOT BEEN MODELED OR INDICATED ON THESE DRAWINGS. IT IS THE CONTRACTOR'S RESPONSIBILITY TO DESIGN AND ROUTE CONDUITS SMALLER THAN 2

IN. FROM THE SOURCE TO THE DESTINATION POINTS.

43. SEQUENCING OF SYSTEMS EQUIPMENT AND PROVISIONING WITHIN THE PROJECT SCOPE MUST BE

COORDINATED WITH THE CONTRACTING OFFICER FOR GOVERNMENT FURNISHED SYSTEMS AND

EQUIPMENT.

44. THE AV DRAWINGS DESCRIBE (A) THE MILCON CONTRACTOR'S BASE "INFRASTRUCTURE" PROVISIONS FOR AV SYSTEMS - SPECIFICALLY INCLUDING AV-RELATED INFRASTRUCTURE (CONDUIT RACEWAYS, BOXES, STRUCTURAL MOUNTING SUBSTRATES, AND AV-SPECIFIC EQUIPMENT CABINETS) TO SUPPORT ALL AV

EQUIPMENT, REGARDLESS OF WHICH VENDOR OR INSTALLER IS HANDLING THE AV EQUIPMENT

INSTALLATION; AND (B) THE SCOPE OF AV EQUIPMENT/SYSTEMS APPROPRIATED AS AV-SPECIFIC "SPECIALTY" COLLATERAL EQUIPMENT (CEQ) ITEMS BY MEANS OF THE CEQ CONTRACT MODIFICATION PROCESS; AND (C) THE SCOPE OF AV EQUIPMENT/SYSTEMS APPROPRIATED AS GOVERNMENT-FURNISHED, GOVERNMENT-INSTALLED (GFGI) ITEMS BY MISSION USERS AND/OR C4IT-DELEGATED TURN-KEY

INSTALLER.

45. REFER TO SPECIFICATION SECTION 27 41 00 "AUDIO-VISUAL SYSTEMS" FOR ADDITIONAL REQUIREMENTS TO

COMPLEMENT THESE DRAWINGS.

46. AV EQUIPMENT AND CABLING IDENTIFIED ON THESE DRAWINGS (AND IN THE RELATED SPECIFICATIONS) AS AV-SPECIFIC "SPECIALTY" COLLATERAL EQUIPMENT (CEQ), MUST BE PROVIDED WITHIN THE AV CEQ PACKAGE. REFER TO THE COMPREHENSIVE INTERIOR DESIGN (CID) PACKAGE'S "AV CEQ" DOCUMENTS

(INCLUDING BASIS OF DESIGN NARRATIVE AND AV EQUIPMENT SCHEDULES) FOR ADDITIONAL

INFORMATION. THE AV-SPECIFIC "SPECIALTY" COLLATERAL EQUIPMENT (CEQ) MUST BE PROVIDED BY A QUALIFIED AND MANUFACTURER-APPROVED AV TRADE CONTRACTOR SPECIALIZING IN THE SALE AND

INSTALLATION OF COMMERCIAL-GRADE AUDIO-VIDEO (AV) SYSTEMS.

47. AV CABLING WILL BE PROVIDED AS PART OF GFGI SCOPE. FOR AV CABLING (WITHOUT EXCEPTION), PROVIDE CABLE RACEWAY INFRASTRUCTURE AS IDENTIFIED ON THESE DRAWINGS.

48. POWER AND DATA COORDINATION REQUIREMENTS ARE CLARIFIED IN THE AV EQUIPMENT SCHEDULES ON THESE DRAWINGS, BUT THE FINAL POWER AND DATA SCOPE IS INDICATED ON THE RESPECTIVE

ELECTRICAL POWER AND TELECOMMUNICATIONS DRAWINGS.

49. NOT ALL PARTS AND PIECES ARE NECESSARILY SHOWN FOR A COMPLETE SYSTEM. UNLESS NOTED OTHERWISE, THE CONTRACTOR AND AV-SPECIFIC CEQ VENDOR/INSTALLER ARE RESPONSIBLE FOR

PROVIDING ONLY THE COMPONENTS SPECIFIED IN THE AV DRAWINGS AND SPECIFICATIONS.

50. THE MILCON GENERAL CONTRACTOR AND THEIR SUB-CONTRACTORS MUST PROVIDE ALL HARDWARE ATTACHED TO THE BUILDING. THIS INCLUDES, BUT IS NOT LIMITED TO, CEILING-MOUNTED EQUIPMENT SUPPORTS, WALL-MOUNTED BACKING SUPPORTS, CABLE TRAY, J-HOOK CABLE SUPPORT PATHS, RACEWAY

AND CONDUIT SYSTEMS, TECHNICAL BONDING/GROUNDING, BRANCH-CIRCUIT POWER

OUTLETS/CONNECTIONS, AND TELE/DATA WORK AREA OUTLETS SPECIFIC TO AV EQUIPMENT PROVISIONS.

51. WHERE DIMENSIONS ARE SHOWN FOR EQUIPMENT SIZES OR MOUNTING HEIGHTS, SUCH DIMENSIONS ARE NOMINAL AND MAY REQUIRE SMALL ADJUSTMENTS FOR FINAL INSTALLATION BASED ON EXACT EQUIPMENT

PROVIDED. WHERE DIMENSIONS ARE CRITICAL, THEY ARE MARKED AS "CRITICAL".

52. PROVIDE BACKING MATERIAL FOR EQUIPMENT WEIGHT THAT IS RATED TO SUPPORT A MINIMUM OF FIVE

TIMES (5X) THE WEIGHT OF THE EQUIPMENT ANCHORED THERETO.

53. THE AV-SPECIFIC CEQ VENDOR/INSTALLER WILL VERIFY THE QUANTITIES OF ALL AV CEQ MATERIALS

SCHEDULED HEREIN, AND PROVIDE THOSE QUANTITIES ACCORDINGLY.

54. AV RACEWAYS MUST BE LABELED WITH PERMANENT TYPED/PRINTED LABELS AT BOTH ENDS OF SYSTEM, AND AT INTERMEDIATE PULL BOXES.

SHEET NO.

NAVFAC DWG. NO. SHEET TITLENO. SHEET

438 TA001 17322326 AV SYSTEMS GENERAL NOTES

439 TA002 17322327 AV SYSTEMS SYMBOLS, LEGEND, AND ABBREVIATIONS

440 TA101 17322328 OVERALL AV FIRST FLOOR PLAN

441 TA102 17322329 PARTIAL AV FIRST FLOOR PLAN - A

442 TA103 17322330 PARTIAL AV FIRST FLOOR PLAN - B

443 TA104 17322331 PARTIAL AV FIRST FLOOR CABLE TRAY PLAN - A

444 TA105 17322332 PARTIAL AV FIRST FLOOR CABLE TRAY PLAN - B

445 TA106 17322333 OVERALL AV SECOND FLOOR PLAN

446 TA107 17322334 PARTIAL AV SECOND FLOOR PLAN - A

447 TA108 17322335 PARTIAL AV SECOND FLOOR PLAN - B

448 TA109 17322336 PARTIAL AV SECOND FLOOR CABLE TRAY PLAN - A

449 TA110 17322337 PARTIAL AV SECOND FLOOR CABLE TRAY PLAN - B

450 TA401 17322338 AV INTERIOR ELEVATIONS

451 TA402 17322339 AV INTERIOR ELEVATIONS

452 TA403 17322340 AV INTERIOR ELEVATIONS

453 TA404 17322341 AV INTERIOR ELEVATIONS

454 TA405 17322342 ENLARGED AV PLANS & INTERIOR ELEVATIONS

455 TA406 17322343 ENLARGED AV PLANS & INTERIOR ELEVATIONS

456 TA407 17322344 ENLARGED AV PLANS & INTERIOR ELEVATIONS

457 TA408 17322345 ENLARGED AV PLANS

458 TA409 17322346 ENLARGED AV PLANS

459 TA410 17322347 AV INTERIOR ELEVATIONS & SECTIONS

460 TA501 17322348 AV INFRASTRUCTURE DETAILS

461 TA502 17322349 AV INFRASTRUCTURE DETAILS

462 TA503 17322350 AV INFRASTRUCTURE DETAILS

463 TA504 17322351 AV INFRASTRUCTURE DETAILS

464 TA601 17322352 AV SYSTEMS SCHEDULES

465 TA701 17322353 AV INFRASTRUCTURE RISER DIAGRAMS

466 TA702 17322354 AV INFRASTRUCTURE RISER DIAGRAMS

467 TA703 17322355 AV INFRASTRUCTURE RISER DIAGRAMS

468 TA704 17322356 AV INFRASTRUCTURE RISER DIAGRAMS

AV SYSTEMS TYPES

LOBBY 1A-1

TYPE DESCRIPTION PLANS / ELEVATIONS RISER DIAGRAM

TA701

N/A

ENTRY CONTROL POINTA-2 TA701

TA102 TA401

TA102 TA104

BREAK ROOMB

TA102 TA108

TA401

TA401 TA402

TA - STANDALONE ROOM / AREA WITH RAFC-1 TA701

TA102 TA103 TA104

TA105 TA107 TA108

TA109 TA110 TA401

TA403 TA404

TA - STANDALONE ROOM / AREA, NO RAFC-2 TA701TA108 TA404

TA - STANDALONE ROOM / AREA WITH RAFC-3

TA102 TA104 TA107

TA109 TA401 TA403

TA702

TECG CONFERENCE ROOME

TA - COC WATCH FLOORH TA704

TA105 TA408

TA409 TA410

TA - COMMAND DECKG TA703

TA105 TA408

TA409 TA410

TA109 TA406 TA702

SVTC CONFERENCE ROOM / SIPR CAFEF

TA104 TA109

TA405 TA407

TA703

TA - DIVISIBLE / COMBINABLE ROOMS / AREASD TA702

TA102 TA104 TA107

TA108 TA109 TA110

TA401 TA402 TA403

TA404

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

APRIL 30, 2028

SIGNATURE EXPIRATION DATE OF LICENSE

Expires:

11/30/2027

Patrick Durham #404250

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

M

A K

A L A

P A

H

A W

A

II

AS NOTED

/1

/2

:1 :1

P

M

A u to d e s k D o c s /J

-8

B S

T F

/B L

D G

-J

-1

-T A

.r v t

TA002

JF

Y

P

R O

JE

C

T J

-8

A V

S Y

S

TE

M S

S Y

M B

O

LS

, L E

G E

N D

, A N

D A

B B

R E

V

IA

TI

O

N S

PKD

17322327

PKD DHC

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

N62742-20-D-0001

M C

B C

A M

P B

LA

Z

, G U

A M

U .S

. N A

V S

U P

P A

C T

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T A

GENERAL DRAWING SYMBOLS

SECTION / CALLOUT VIEW REFERENCE

XX

XX

XX

XX

NUMBER OF DETAIL ON SHEET

NUMBER OF SHEET WHERE DETAIL APPEARS

CENTERLINECL

MATCHLINE WITH VIEW REFERENCE

KEYED NOTEX

REVISION NUMBERX

ROOM NAME AND NUMBER

DOOR TAG - REFERENCE ARCHITECTURAL DOOR SCHEDULE FOR MORE

INFORMATION

ROOM NAME

XXX

XXX NEW

GRAPHICAL REPRESENTATION OF PHASING (TYP FOR ALL SYMBOLS)

XXX GOVERNMENT-FURNISHED OR FUTURE, AS NOTED

RACEWAY SYMBOLS & LINETYPES

CONDUIT, RACEWAY, OR CABLE TRAY CONCEALED IN WALL OR ABOVE CEILING

CONDUIT, RACEWAY, OR CABLE TRAY IN RAF, BELOW FLOOR OR GRADE

CONDUIT STUB OUT WITH NYLON BUSHINGS

CONDUIT RISER UP/DOWN

HOMERUN CONDUIT

(XX) ##

YY

YY = DESTINATION

## = CONDUIT TRADE SIZE

XX = CONDUIT QUANTITY (ONE IF NONE LISTED)

LADDER-STYLE CABLE TRAY

WIRE MESH-STYLE CABLE TRAY

CHANNEL-STYLE CABLE TRAY

FIRE-RATED PATHWAY DEVICE

X#

NOTES:

F = FIRE-RATED PATHWAY

S = SMOKE & ACOUSTICAL PATHWAY

# = NUMBER OF PATHWAY DEVICES

AV SYSTEMS SYMBOLS

AV ROOM CLASSIFICATION "DIGITAL SIGN" DISPLAY - WALL (GFGI)

AV RECESSED FLOOR OUTLET BOX (CFCI / MILCON)

FLAT PANEL VIDEO MONITOR FOR LOCAL PRESENTATION / CONFERENCING

ACTIVITIES AND CABLE TV FEED (BY AV CEQ VENDOR)

"xx" INDICATES DIAGONAL SCREEN SIZE

FBx

VIDEO CONFERENCING (VTC) CAMERA (GFGI)

LOUDSPEAKER - RECESSED OR SURFACE-MOUNTED (GFGI)Sx

AV-EQUIPPED FURNITURE (BY AV CEQ VENDOR)

AV EQUIPMENT RACK/CABINET (CFCI/MILCON)

XX

XX

RCx

FP2-xx

VCx

AV SYSTEMS ABBREVIATIONS

MATCHLINE

XX / XX

# POUNDS (SAME AS "LB" AND "LBS")

A AMPERE

ABA ARCHITECTURAL BARRIERS ACT

AC ABOVE COUNTER

ADA AMERICANS WITH DISABILITIES ACT

ADDL ADDITIONAL

ADJ ADJUSTABLE

AFC ABOVE FINISHED CEILING

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

ALS ASSISTIVE LISTENING SYSTEM

ALT ALTERNATE

AMP AMPLIFIER

ANSI AMERICAN NATIONAL STANDARDS INSTITUTE

ANT ANTENNA

APPROX APPROXIMATE, APPROXIMATELY

ARCH ARCHITECTURAL

ATC AUDIO TELECONFERENCING

AUX AUXILIARY

AV AUDIO-VIDEO, AUDIO-VISUAL, AUDIOVISUAL

AVC AUDIO-VIDEO SYSTEMS CONTRACTOR

AVOIP AUDIO-VIDEO OVER INTERNET PROTOCOL

AWG AMERICAN WIRE GAUGE

BB BACK BOX

BC BONDING CONDUCTOR

BET BUILDING ENTRANCE TERMINAL

BFC BELOW FINISHED CEILING

BLDG BUILDING

C CONDUIT

C4I/IT COMMAND, CONTROL, COMMUNICATIONS, COMPUTERS AND INFORMATION TECHNOLOGY

CAB EQUIPMENT CABINET

CAM CAMERA

CAT CATEGORY (TWISTED PAIR CABLING)

CATV COMMUNITY ACCESS TELEVISION OR CABLE TELEVISION

CC CONTACT CLOSURE

CEQ COLLATERAL EQUIPMENT

CFCI CONTRACTOR-FURNISHED, CONTRACTOR-INSTALLED

CH CHANNEL

CID COMPREHENSIVE INTERIOR DESIGN

CKT CIRCUIT

CL CENTER LINE

CLG CEILING

CLK CLOCK

CM COMMUNICATIONS MULTIPURPOSE (CABLE)

CMP COMMUNICATIONS PLENUM RATED (CABLE)

CMR COMMUNICATIONS RISER RATED (CABLE)

CO CONTRACTING OFFICER

COAX COAXIAL

COC COMMAND OPERATIONS CENTER

CODEC ENCODER / DECODER

COMM COMMUNICATIONS

CONF CONFERENCE

CONT'D CONTINUED

CP CONTROL PANEL

CPU CENTRAL PROCESSING UNIT

CT CABLE TRAY

CTR COMMERCIAL TELECOMMUNICATIONS ROOM

CTRL CONTROL

DB DECIBEL

DED DEDICATED

DEG DEGREES

DIA DIAMETER

DIAG DIAGONAL

DIM DIMENSION

DISP DISPLAY

DIST DISTRIBUTION

DOR DESIGNER OF RECORD

DSP DIGITAL SIGNAL PROCESSOR

DWG DRAWING

EA EACH

EC ELECTRICAL CONTRACTOR

EGC EQUIPMENT GROUNDING CONDUCTOR

ELEC, ELECT ELECTRICAL

EM EMERGENCY

EMT ELECTRICAL METALLIC TUBING

ENCL ENCLOSURE

ENT ELECTRICAL NON-METALLIC TUBING

EPTZ ELECTRONIC PAN-TILT-ZOOM

EQ EQUAL, EQUIVALENT

EQUIP EQUIPMENT

ER EQUIPMENT RACK

ESS ELECTRONIC SECURITY SYSTEM(S)

FA FIRE ALARM

FACP FIRE ALARM CONTROL PANEL

FB FLOOR BOX

FC FERRULE CONNECTOR (FIBER-OPTIC TERMINATION)

FF FINISHED FLOOR

FF&E FURNITURE, FIXTURES & EQUIPMENT

FIXT FIXTURE

FLR FLOOR

FMC FLEXIBLE METAL CONDUIT

FO FIBER OPTIC

FP FLAT PANEL VIDEO MONITOR

FPS FRAMES PER SECOND

FT FOOT, FEET

FTP FOILED TWISTED PAIR CABLE

G, GND GROUND

GALV GALVANIZED

GC GENERAL CONTRACTOR

GFCI GOVERNMENT FURNISHED, CONTRACTOR INSTALLED

GFGI GOVERNMENT FURNISHED, GOVERNMENT INSTALLED

GOVT GOVERNMENT

GRC GALVANIZED RIGID CONDUIT (A TYPE OF "RMC")

GTR GOVERNMENT TELECOMMUNICATIONS ROOM

GYP GYPSUM

HDBT HDBASET

HDMI HIGH-DEFINITION MULTIMEDIA INTERFACE

HDPE HIGH-DENSITY POLYETHYLENE CONDUIT

HDR HIGH DYNAMIC RANGE

HF HIGH FREQUENCY

HH HAND HOLE (IN-GRADE PULL BOX)

HORIZ HORIZONTAL

HZ HERTZ

I/O INPUT / OUTPUT

IBC INTERNATIONAL BUILDING CODE

IC INTERCOM

ICT INFORMATION AND COMMUNICATIONS TECHNOLOGY

ID INSIDE DIAMETER

IDF INTERMEDIATE DISTRIBUTION FRAME

IG ISOLATED GROUND

IMC INTERMEDIATE METAL CONDUIT

IN INCH, INCHES

INCL INCLUDE, INCLUDED

IP INTERNET PROTOCOL

IR INFRARED

IT INFORMATION TECHNOLOGY

J, JB, J-BOX JUNCTION BOX

KO KNOCK-OUT

KP KEYPAD

KTR CONTRACTOR

KVM KEYBOARD-VIDEO-MOUSE

KYBD KEYBOARD

LAN LOCAL AREA NETWORK

LB, LBS POUNDS (SAME AS "#")

LC LATCHING CONNECTOR (FIBER OPTIC TERMINATION)

LCD LIQUID CRYSTAL DISPLAY

LCR LEFT/CENTER/RIGHT AUDIO

LED LIGHT EMITTING DIODE

LF LOW FREQUENCY

LFMC LIQUID-TIGHT FLEXIBLE METALLIC CONDUIT

LFNC LIQUID-TIGHT FLEXIBLE NON-METALLIC CONDUIT

LR LEFT/RIGHT (STEREO) AUDIO

LT LIQUID TIGHT

LTG LIGHTING

LV LOW-VOLTAGE

MAX MAXIMUM

MDF MAIN DISTRIBUTION FRAME

MECH MECHANICAL

MFR MANUFACTURER

MIC MICROPHONE

MILCON MILITARY CONSTRUCTION

MIN MINIMUM

MISC MISCELLANEOUS

MM MULTIMODE (OPTICAL FIBER)

MNS MASS NOTIFICATION SYSTEM

MOD MODIFIED

MON MONITOR

MTC MULTI-TIME ZONE CLOCK

MTD MOUNTED

MTG MOUNTING

NAVFAC NAVAL FACILITIES ENGINEERING SYSTEMS COMMAND

NEC NATIONAL ELECTRICAL CODE

NEMA NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION

NFPA NATIONAL FIRE PROTECTION ASSOCIATION

NIC NOT IN CONTRACT

NOM NOMINAL

NTS NOT TO SCALE

OC ON CENTER

OD OUTSIDE DIAMETER

OH OVERHEAD

OSP OUTSIDE PLANT

PA PUBLIC ADDRESS

PB PULL BOX

PBB PRIMARY BONDING BUSBAR

PC PERSONAL COMPUTER

PDU POWER DISTRIBUTION UNIT

PJ, PROJ PROJECTOR

PLYWD PLYWOOD

PNL PANEL

POE POWER OVER ETHERNET

PR PAIR

PS PROJECTION SCREEN

PTZ PAN-TILT-ZOOM

PVC POLYVINYL CHLORIDE

PWR POWER

QTY QUANTITY

RAF RAISED ACCESS FLOORING

RBB RACK BONDING BUSBAR

RBC RACK BONDING CONDUCTOR

RCP REFLECTED CEILING PLAN

RCPT RECEPTACLE

RE, REF REFER (TO) OR REFERENCE

REQ REQUIRED

RF RADIO FREQUENCY

RGB RED-GREEN-BLUE

RIO ROUGH-IN ONLY

RM ROOM

RMC RIGID METAL CONDUIT

RSD ROOM STATUS DISPLAY / INDICATOR LIGHT

RU RACK UNIT(S)

RX RECEIVER

S, SPKR SPEAKER, LOUDSPEAKER

SBB SECONDARY BONDING BUSBAR

SC SUBSCRIBER CONNECTOR (FIBER-OPTIC TERMINATION)

SCC STRUCTURED CABLING CONTRACTOR

SCHED SCHEDULE

SCRN SCREEN

SCS STRUCTURED CABLING SYSTEM

SFP SMALL FORM-FACTOR PLUGGABLE

SIM SIMILAR

SM SINGLEMODE (OPTICAL FIBER)

SPD SURGE PROTECTIVE DEVICE

SPECS SPECIFICATIONS

SPL SOUND PRESSURE LEVEL

SS SPECIAL SYSTEMS

SST STAINLESS STEEL

ST STRAIGHT TERMINUS CONNECTOR (FIBER OPTIC TERMINATION)

STD STANDARD

STP SHIELDED TWISTED PAIR CABLE

STR STRAND

STRUCT STRUCTURAL

TA TRAINING AUDIENCE

TBB TELECOM BONDING BACKBONE

TBC TELECOM BONDING CONDUCTOR

TBD TO BE DETERMINED

TCP/IP TRANSMISSION CONTROL PROTOCOL / INTERNET PROTOCOL

TELECOM TELECOMMUNICATIONS

TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION

TP TOUCH PANEL

TR TELECOMMUNICATIONS ROOM

TV TELEVISION

TX TRANSMITTER

TYP TYPICAL

UC UNDER COUNTER

UFC UNIFIED FACILITIES CRITERIA

UG UNDERGROUND

UL UNDERWRITERS LABORATORIES

UON UNLESS OTHERWISE NOTED

UPS UNINTERRUPTIBLE POWER SUPPLY

USB UNIVERSAL SERIAL BUS

UTP UNSHIELDED TWISTED PAIR CABLE

V VOLT(S)

VA VOLT-AMP(S)

VAC VOLTS ALTERNATING CURRENT

VC VIDEO CAMERA

VCD VOLUME CONTROL (VOLUME ATTENUATOR) DEVICE

VDC VOLTS DIRECT CURRENT

VERT VERTICAL

VIF VERIFY IN FIELD

VOIP VOICE OVER INTERNET PROTOCOL

VOL VOLUME

VR VANDAL RESISTANT

VTC VIDEO TELECONFERENCING

W WATT(S)

WL WIRELESS

WP WEATHERPROOF

XCVR TRANSCEIVER

FLAT PANEL VIDEO MONITOR FOR LOCAL PRESENTATION / CONFERENCING

ACTIVITIES (BY AV CEQ VENDOR)

"xx" INDICATES DIAGONAL SCREEN SIZE

FP1-xx

FLAT PANEL VIDEO MONITOR FOR CABLE TV FEED ONLY

(BY AV CEQ VENDOR)

"xx" INDICATES DIAGONAL SCREEN SIZE

FP3-xx

FLAT PANEL VIDEO MONITOR (GFGI)

FP0-xx

AV PULL BOX - CEILING (CFCI / MILCON)Jx

AV JUNCTION BOX FOR WALL DEVICE / WALL PLATE (CFCI / MILCON)Jx

MICROPHONE - CEILING (GFGI)Mx

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

APRIL 30, 2028

SIGNATURE EXPIRATION DATE OF LICENSE

Expires:

11/30/2027

A

B

C

D

E

F

G

TA103

A1

TA102

A1

1 2 3 4 5 6 7 8 9

TA - G4 LOGISTICS

TA - G7 COMM

STRAT

TA - G3 FOPS

105B

TA - G3 FOPS

105A

TA - G2

COLLECTIONS

AND ANALYSIS

108A

TA - HQ CAMP

COMMANDANT

TA - G3 FIRES

TA - G3 STRIKE

CELL

110A

TA - G3 STRIKE

CELL

110B

INTERIOR COC

TRAINING PAD

TA - G2

COLLECTIONS

AND ANALYSIS

108B

GTR 1T (TRAINING

TELECOMM RM)

GTR 1

SVTC CONF RM /

SIPR CAFE

MECH RM

ELEC RM

TA - MEDICAL

CELL

TA - COC WATCH

FLOOR

TA - G5 PLANS

TA - COMMAND

DECK

TA - G1

OPERATIONS

LOBBY 1

L1

ENTRY VESTIBULE

CTR 1

ELEV MACHINE RM

ELEV 1

E1

NURSING RM

BREAK RM

ENTRY CONTROL

POINT

102A

CORRIDOR 1C

C1C

VESTIBULE 1A

V1A

VESTIBULE 1C

V1C

VESTIBULE 1D

V1D

CORRIDOR 1A

C1A

ELEC CLOSET

CORRIDOR 1B

C1B

WOMEN

MEN

JAN

CORRIDOR 1E

C1E

OFFICE

128B

OFFICE

128A

OFFICE

127B

OFFICE

127A

OFFICE

126B

OFFICE

126A

VESTIBULE 1E

V1E

TELCOM CLOSET

126C

AV CLOSET

126D

STAIR 1C

S1C

STAIR 1B

S1B

STAIR 1A

S1A

OFFICE

125A

TRAINING

MATERIAL

STORAGE

EMERGENCY

GENERATOR

TA105

A1

TA104

A1

1. REFER TO TA001 & TA002 FOR AV REQUIREMENTS AND SYMBOLS SHOWN ON THESE DRAWINGS. WORK MUST BE

PERFORMED IN COMPLIANCE WITH DIVISION 27 SPECIFICATIONS.

2. NOT ALL ARCHITECTURAL, TELECOM AND ELECTRICAL ELEMENTS HAVE BEEN INCLUDED ON THE DRAWINGS, CONTRACTOR MUST REFER TO THOSE RESPECTIVE DISCIPLINES' SHEETS FOR ADDITIONAL BUILDING-MOUNTED ELEMENTS AND SCOPE OF WORK THAT MAY INTERFACE WITH, OR IMPACT, THE AV SCOPE OF WORK.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

M

A K

A L A

P A

H

A W

A

II

AS NOTED

/1

/2

:1 :1

P

M

A u to d e s k D o c s /J

-8

B S

T F

/B L

D G

-J

-1

-T A

.r v t

TA101

JF

Y

P

R O

JE

C

T J

-8

O V

E R

A

LL

A V

F

IR

S T

F

LO

O R

P

LA

N

PKD

17322328

PKD DHC

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

N62742-20-D-0001

M C

B C

A M

P B

LA

Z

, G U

A M

U .S

. N A

V S

U P

P A

C T

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T A

PLAN

NORTH

1/16" = 1' - 0" 0 5' 10' 20' 30' 60'

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

KEY PLAN

1/16" = 1'-0"

OVERALL AV SYSTEMS FIRST FLOOR PLAN

A1

AREA A AREA B

M A

T C

H

LI

N E

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

APRIL 30, 2028

SIGNATURE EXPIRATION DATE OF LICENSE

Expires:

11/30/2027

J1

FP3-55

FP

2-

J1

FP2-75

FP1-98

J2

J1

J1

J1 J1

J1 J1

J1 J1

J1

MTCMTC

M

TC

M

TC

M

TC

M

TC

MTC

M

TC

M

TC

A

B

C

D

E

F

G

TA401

TA405

A1

TA405

A3

RCP

C1

MATCHLIN

E

TA103

MATCHLINE

TA103

TA402 C1

TA401

TA401

B1

B2

TA401

D3

TA402A1

TA401

C3

TA402 B1

TA401 A1

1 2 3 4 5 6

TA401 B3

C2

AV SYSTEM

TYPE B

AV SYSTEM

TYPE C-3

AV SYSTEM

TYPE A-2

AV SYSTEM

TYPE A-1

AV SYSTEM

TYPE C-1

AV SYSTEM

TYPE C-1

AV SYSTEM

TYPE C-1

AV SYSTEM TYPE D

A V

S Y

S T

E M

T Y

P E

D

A V

S Y

S T

E M

T Y

P E

D

TA401 D1

TA - G4 LOGISTICS

TA - G7 COMM

STRAT

TA - HQ CAMP

COMMANDANT

ENTRY CONTROL

POINT

102A

ENTRY VESTIBULE

LOBBY 1

L1

BREAK RM

NURSING RM

ELEC CLOSET

TA - G3 FIRES

TA - G3 STRIKE

CELL

110A

TA - G3 STRIKE

CELL

110B

CORRIDOR 1C

C1C

TA - G2

COLLECTIONS

AND ANALYSIS

108A

TA - G2

COLLECTIONS

AND ANALYSIS

108B

INTERIOR COC

TRAINING PAD

TA - G3 FOPS

105B

TA - G3 FOPS

105A

SVTC CONF RM /

SIPR CAFE

GTR 1

GTR 1T (TRAINING

TELECOMM RM)

CTR 1

ELEV MACHINE RM

ELEV 1

E1

VESTIBULE 1D

V1D

VESTIBULE 1A

V1A

STAIR 1B

S1B

CORRIDOR 1B

C1B

CORRIDOR 1A

C1A

CORRIDOR 1D

C1D

MECH RM

EQ EQ

11' - 5"

11' - 6" 11' - 6"

9' - 4"

TO FP2-75 IN

LOBBY 1

4' - 6"

(A V

-4

(AV-6)

(AV-3)

(AV-4)

(A V

-3

(AV-3)(AV-3)

(AV-3)

(A V

-3

(A V

-3

(A V

-3

(A V

-3

(A V

-3

FP1-98FP1-98

FP

1-

FP1-98

FP

1-

FP

1-

FP

1-

FP

1-

FP

1-

1. REFER TO TA001 & TA002 FOR AV REQUIREMENTS AND SYMBOLS SHOWN ON THESE DRAWINGS. WORK MUST BE

PERFORMED IN COMPLIANCE WITH DIVISION 27 SPECIFICATIONS.

2. NOT ALL ARCHITECTURAL, TELECOM AND ELECTRICAL ELEMENTS HAVE BEEN INCLUDED ON THE DRAWINGS, CONTRACTOR MUST REFER TO THOSE RESPECTIVE DISCIPLINES' SHEETS FOR ADDITIONAL BUILDING-MOUNTED ELEMENTS AND SCOPE OF WORK THAT MAY INTERFACE WITH, OR IMPACT, THE AV SCOPE OF WORK.

3. CONDUIT RACEWAYS SHOWN ON PLAN AND RCP VIEWS ARE ONLY SHOWN IF A SPECIFIC ROUTE IS REQUIRED.

REFER TO PATHWAY RISER DIAGRAMS FOR CONDUIT RACEWAY REQUIREMENTS. COORDINATE ROUTING AND ROOM ENTRY LOCATIONS FOR AV SYSTEMS CONDUIT AND PATHWAYS DURING SHOP DRAWING PROCESS.

4. VERIFY AND COORDINATE WALL SPACE REQUIREMENTS WITH OTHER TRADES DURING SHOP DRAWING

PROCESS TO CONFIRM FINAL PLACEMENT OF AV ROUGH-IN’S AND EQUIPMENT.

5. VERIFY EQUIPMENT ROUGH-IN DIMENSIONS WITH VENDOR/INSTALLER.

6. REFER TO I-SERIES (INTERIOR DESIGN) DRAWINGS FOR FINAL DIMENSIONS OF:

a. HORIZONTAL MOUNTING OF WALL-MOUNTED AV-EQUIPMENT

b. POSITIONING OF AV-RELATED FURNITURE/FURNISHINGS. FOR AV EQUIPMENT CABINETS, REFER TO

DIMENSIONS ON THE TA-SERIES DRAWINGS.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

M

A K

A L A

P A

H

A W

A

II

AS NOTED

/1

/2

:1 :1

P

M

A u to d e s k D o c s /J

-8

B S

T F

/B L

D G

-J

-1

-T A

.r v t

TA102

JF

Y

P

R O

JE

C

T J

-8

P A

R

TI

A L

A V

F

IR

S T

F

LO

O R

P

LA

N

A

PKD

17322329

PKD DHC

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

N62742-20-D-0001

M C

B C

A M

P B

LA

Z

, G U

A M

U .S

. N A

V S

U P

P A

C T

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T A

1/8" = 1'-0"

AV SYSTEMS FIRST FLOOR PLAN - A

A1

AREA A AREA B

M A

T C

H

LI

N E

PLAN

NORTH

1/8" = 1' - 0" 0 5' 10' 15' 30'

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

KEY PLAN

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

APRIL 30, 2028

SIGNATURE EXPIRATION DATE OF LICENSE

Expires:

11/30/2027

M

TC

A

B

C

D

E

F

G

TA408

A1

TA409

A1

RCP

MATCHLIN

E

TA102

MATCHLINE

TA102

5 6 7 8 9

AV SYSTEM

TYPE C-1

TA402 C3

ENTRY VESTIBULE

LOBBY 1

L1

CTR 1

ELEV MACHINE RM

ELEV 1

E1

CORRIDOR 1D

C1D

TA - COC WATCH

FLOOR

VESTIBULE 1E

V1E

OFFICE

126A

OFFICE

126B

OFFICE

127B

OFFICE

127A

OFFICE

128A

OFFICE

128B

TA - G1

OPERATIONS

TA - COMMAND

DECK

TA - G5 PLANS

STAIR 1A

S1A

MECH RM

ELEC RM

MEN

JAN

WOMEN

OFFICE

125A

TA - MEDICAL

CELL

TELCOM CLOSET

126C

AV CLOSET

126D

STAIR 1C

S1C

CORRIDOR 1E

C1E

TELCOM CLOSET

128C

TRAINING

MATERIAL

STORAGE

EMERGENCY

GENERATOR

(A V

-3

FP

1-

1. REFER TO TA001 & TA002 FOR AV REQUIREMENTS AND SYMBOLS SHOWN ON THESE DRAWINGS. WORK MUST BE

PERFORMED IN COMPLIANCE WITH DIVISION 27 SPECIFICATIONS.

2. NOT ALL ARCHITECTURAL, TELECOM AND ELECTRICAL ELEMENTS HAVE BEEN INCLUDED ON THE DRAWINGS, CONTRACTOR MUST REFER TO THOSE RESPECTIVE DISCIPLINES' SHEETS FOR ADDITIONAL BUILDING-MOUNTED ELEMENTS AND SCOPE OF WORK THAT MAY INTERFACE WITH, OR IMPACT, THE AV SCOPE OF WORK.

3. CONDUIT RACEWAYS SHOWN ON PLAN AND RCP VIEWS ARE ONLY SHOWN IF A SPECIFIC ROUTE IS REQUIRED.

REFER TO PATHWAY RISER DIAGRAMS FOR CONDUIT RACEWAY REQUIREMENTS. COORDINATE ROUTING AND ROOM ENTRY LOCATIONS FOR AV SYSTEMS CONDUIT AND PATHWAYS DURING SHOP DRAWING PROCESS.

4. VERIFY AND COORDINATE WALL SPACE REQUIREMENTS WITH OTHER TRADES DURING SHOP DRAWING

PROCESS TO CONFIRM FINAL PLACEMENT OF AV ROUGH-IN’S AND EQUIPMENT.

5. VERIFY EQUIPMENT ROUGH-IN DIMENSIONS WITH VENDOR/INSTALLER.

6. REFER TO I-SERIES (INTERIOR DESIGN) DRAWINGS FOR FINAL DIMENSIONS OF:

a. HORIZONTAL MOUNTING OF WALL-MOUNTED AV-EQUIPMENT

b. POSITIONING OF AV-RELATED FURNITURE/FURNISHINGS. FOR AV EQUIPMENT CABINETS, REFER TO

DIMENSIONS ON THE TA-SERIES DRAWINGS.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

P A

C

IF

IC

M

A K

A L A

P A

H

A W

A

II

AS NOTED

/1

/2

:1 :1

P

M

A u to d e s k D o c s /J

-8

B S

T F

/B L

D G

-J

-1

-T A

.r v t

TA103

JF

Y

P

R O

JE

C

T J

-8

P A

R

TI

A L

A V

F

IR

S T

F

LO

O R

P

LA

N

B

PKD

17322330

PKD DHC

3/10/2026

NATHANIEL PYRON, MILCON

PLANNER, DPPH

B A

TT

LE

S

TA

FF

T

R A

IN

IN

G F

A C

IL

IT

Y

DKS/DMK

1696746

N62742-20-D-0001

M C

B C

A M

P B

LA

Z

, G U

A M

U .S

. N A

V S

U P

P A

C T

KYM

KYM

RYO

N A

V F

A C

P A

C

IF

IC

T A

1/8" = 1'-0"

AV SYSTEMS FIRST FLOOR PLAN - B

A1

AREA A AREA B

M A

T C

H

LI

N E

PLAN

NORTH

1/8" = 1' - 0" 0 5' 10' 15' 30'

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

KEY PLAN

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

APRIL 30, 2028

SIGNATURE EXPIRATION DATE OF LICENSE

Expires:

11/30/2027

C

D

E

F

G

1 2 3 4 5 6

TA - G4 LOGISTICS

TA - G7 COMM

STRAT

TA - HQ CAMP

COMMANDANT

ENTRY CONTROL

POINT

102A

ENTRY VESTIBULE

LOBBY 1

L1

BREAK RM

NURSING RM

ELEC CLOSET

TA - G3 FIRES

TA - G3 STRIKE

CELL

110A

TA - G3 STRIKE

CELL

110B

CORRIDOR 1C

C1C

TA - G2

COLLECTIONS

AND ANALYSIS

108A

TA - G2

COLLECTIONS

AND ANALYSIS

108B

INTERIOR COC

TRAINING PAD

TA - G3 FOPS

105B

TA - G3 FOPS

105A

SVTC CONF RM /

SIPR CAFE

GTR 1

GTR 1T (TRAINING

TELECOMM RM)

CTR 1

ELEV MACHINE RM

ELEV 1

E1

VESTIBULE 1D

V1D

VESTIBULE 1A

V1A

STAIR 1B

S1B

CORRIDOR 1B

C1B

CORRIDOR 1A

C1A

CORRIDOR 1D

C1D

OFFICE

128B

MECH RM

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

4"x2" WIRE

MESH CABLE

TRAY

MATCHLIN

E

TA105

MATCHLINE

TA105

1. REFER TO TA001 & TA002 FOR AV REQUIREMENTS AND SYMBOLS SHOWN ON THESE DRAWINGS. WORK MUST BE

PERFORMED IN COMPLIANCE WITH DIVISION 27 SPECIFICATIONS.

2. NOT ALL ARCHITECTURAL, TELECOM AND ELECTRICAL ELEMENTS HAVE BEEN INCLUDED ON THE DRAWINGS, CONTRACTOR MUST REFER TO THOSE RESPECTIVE DISCIPLINES' SHEETS FOR ADDITIONAL BUILDING-MOUNTED ELEMENTS AND SCOPE OF WORK THAT MAY INTERFACE WITH, OR IMPACT, THE AV SCOPE OF WORK.

3. CONDUIT RACEWAYS SHOWN ON PLAN AND RCP VIEWS ARE ONLY SHOWN IF A SPECIFIC ROUTE IS REQUIRED.

REFER TO PATHWAY RISER DIAGRAMS FOR CONDUIT RACEWAY REQUIREMENTS. COORDINATE ROUTING AND ROOM ENTRY LOCATIONS FOR AV SYSTEMS CONDUIT AND PATHWAYS DURING SHOP DRAWING PROCESS.

4. VERIFY AND COORDINATE WALL SPACE REQUIREMENTS WITH OTHER TRADES DURING SHOP DRAWING

PROCESS TO CONFIRM FINAL PLACEMENT OF AV ROUGH-IN’S AND EQUIPMENT.

5. VERIFY EQUIPMENT ROUGH-IN DIMENSIONS WITH VENDOR/INSTALLER.

6. REFER TO I-SERIES (INTERIOR DESIGN) DRAWINGS FOR FINAL DIMENSIONS OF:

a. HORIZONTAL MOUNTING OF WALL-MOUNTED AV-EQUIPMENT

b. POSITIONING OF AV-RELATED FURNITURE/FURNISHINGS. FOR AV EQUIPMENT CABINETS, REFER TO

DIMENSIONS ON THE TA-SERIES DRAWINGS.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M…