Att 3 Volume 3 - Architectural_Combined.pdf

N

N

CHILLICOTHE VA MEDICAL CENTER

PROJECT NUMBER: 538-21-701

DEPARTMENT OF VETERANS AFFAIRS

273 STATE ROUTE 104, CHILLICOTHE, OHIO 45601

EHRM INFRASTRUCTURE UPGRADES

VOLUME 3 OF 13

G E N E R A L N O T E S

A. SEE GENERAL PROJECT NOTES FOR NEW WORK FOR ADDITIONAL REQUIREMENTS FOR WORK WITHIN THE

EXISTING FACILITY. THE CONTRACTOR SHALL VERIFY ALL EXISTING DIMENSIONS AND FIELD CONDITIONS

PRIOR TO DEMOLITION AND CONSTRUCTION. IF PROVIDED, THE GENERAL CONTRACTOR SHALL EXAMINE

EXISTING BUILDING DOCUMENTS. THE CONTRACTOR SHALL BRING ANY DISCREPANCIES TO THE

IMMEDIATE ATTENTION OF THE C.O.R. THE CONTRACTOR IS RESPONSIBLE FOR THE PROTECTION OF

EXISTING ITEMS TO REMAIN DURING DEMOLITION AND CONSTRUCTION. MAINTAIN EXIT EGRESS PATHS

TO EXISTING EXIT DOORS DURING CONSTRUCTION.

B. THE CONTRACTOR IS RESPONSIBLE FOR THE PROTECTION OF ALL CONSTRUCTION ROUTES BEYOND THE

AREAS OF WORK AND THE ROUTES MUST BE RETURNED TO THEIR ORIGINAL CONDITION AT THE END OF

THE PROJECT.

C. ALL DEMOLITION AND CONSTRUCTION ACTIVITIES SHALL BE COORDINATED WITH THE C.O.R. TO MINIMIZE

DISRUPTIONS OF NORMAL FUNCTIONS OF THE VA'S OCCUPIED AREAS.

D. IF CONSTRUCTION NOISE IS ANTICIPATED, SUBMIT A WRITTEN REQUEST TO THE C.O.R. FOR THE

SCHEDULED TIME OF THE CONSTRUCTION ACTIVITIES. NO WORK SHALL BE DONE WITHOUT THE WRITTEN

APPROVAL OF THE C.O.R. THE C.O.R. RESERVES THE RIGHT TO DISCONTINUE NOISY CONSTRUCTION AT

ANY TIME. NO RADIOS SHALL BE PERMITTED AT ANY TIME IN WORK AREAS ADJACENT TO OCCUPIED

SPACES.

E. ALL EXISTING SERVICES AND UTILITIES SHALL BE MAINTAINED TO AREAS THAT ARE IN OPERATION AND

SERVED BY THEM. COORDINATE ALL DISRUPTIONS OR DISCONTINUATIONS OF UTILITIES AND SERVICES

WITH C.O.R. NO SHUT DOWN OF EXISTING SERVICES IS ALLOWED TO OCCUR UNTIL RECEIVING THE

C.O.R.'S WRITTEN APPROVAL OF THE SHUT DOWN SCHEDULE. PROVIDE TEMPORARY SERVICES AND/OR

UTILITIES DURING INTERRUPTIONS AS REQUIRED AND APPROVED BY THE C.O.R.

F. THE CONTRACTOR SHALL TAKE ALL NECESSARY PRECAUTIONS TO PREVENT DAMAGE TO THE V.A.'S

AREAS ADJACENT TO NEW CONSTRUCTION OR AREAS WHERE VARIOUS SYSTEM CONNECTIONS OR

EXTENSIONS ARE REQUIRED. IN THESE AREAS, THE CONTRACTOR IS RESPONSIBLE FOR DAMAGE

CAUSED BY LACK OF SUFFICIENT PROTECTION FROM THE WEATHER AND FROM THE RESULTS OF ALL

CONSTRUCTION ACTIVITY INCLUDING BUT NOT LIMITED TO DUST AND WATER.

G. THE CONTRACTOR SHALL RECEIVE WRITTEN APPROVAL FROM THE C.O.R. BEFORE USING OPEN FLAMES, WELDING RODS AND TORCHES. THE CONTRACTOR IS RESPONSIBLE FOR ALL MEANS AND METHODS TO

PROHIBIT THE MIGRATION OF SMOKE AND OTHER PRODUCTS OF COMBUSTION INTO OCCUPIED AREAS OF

THE EXISTING BUILDING AND FOR OBTAINING ALL REQUIRED PERMITS RELATED TO HOT WORK.

H. DO NOT OVERLOAD THE EXISTING BUILDING STRUCTURE. MAINTAIN THE STRUCTURAL INTEGRITY OF ALL

STRUCTURAL FRAMING MEMBERS AND SYSTEMS AT ALL TIMES.

I. ALL DEMOLISHED MATERIAL, EXCEPT MATERIAL THAT IS LISTED OR MARKED FOR RETENTION, SHALL

BECOME THE PROPERTY OF THE CONTRACTOR AND IT SHALL BE DISPOSED OF. NO DEBRIS RESULTING

FROM WORK SHALL BE LEFT IN THE CONSTRUCTION ROUTES BEYOND THE AREAS OF WORK.

J. REMOVAL OF A PARTICULAR ITEM IS TO INCLUDE ALL RELATED ITEMS, SUCH AS REMOVAL OF WALLS

WOULD INCLUDE ASSOCIATED DOORS, HARDWARE, ELECTRICAL, PLUMBING, MECHANICAL, ETC. REFER

TO DEMOLITION DRAWINGS FOR MORE INFORMATION. FOR ALL REMOVALS, THE GENERAL CONTRACTOR

AND SUBCONTRACTORS SHALL COORDINATE WITH ALL OTHER DISCIPLINES.

K. THE CONTRACTOR SHALL PROVIDE TEMPORARY SUPPORT FOR ITEMS NOT DEMOLISHED OR REMOVED

AS REQUIRED UNTIL PERMANENT SUPPORT IS PROVIDED IN THE FINAL CONSTRUCTION.

L. ALL OPENINGS IN EXISTING WALLS, CEILINGS AND FLOORS, WHICH ARE THE RESULT OF REMOVALS AND

OTHER NEW CONSTRUCTION ACTIVITY, SHALL BE PATCHED WITH NEW MATERIALS THAT MATCH THE

EXISTING MATERIALS OR AS NOTED ON DRAWINGS. IF THE PATCH IS TO BE MADE IN FIRE RATED

CONSTRUCTION, THE PATCH MUST ACHIEVE THE REQUIRED FIRE RATING. THE PATCH SHALL BE FINISHED

TO A LIKE NEW CONDITION TO MATCH THE EXISTING FINISH.

M. ALL EXISTING OPENINGS IN CEILINGS, FLOORS AND WALLS DISCOVERED IN THE EXISTING STRUCTURE

SHALL BE PATCHED WITH NEW MATERIALS THAT MATCH THE EXISTING MATERIALS. IF THE PATCH IS TO

BE MADE IN FIRE RATED CONSTRUCTION, THE PATCH MUST ACHIEVE THE REQUIRED FIRE RATING. THE

PATCH SHALL BE FINISHED TO A LIKE NEW CONDITION TO MATCH THE EXISTING FINISH.

N. WHERE EXISTING SURFACES ARE TO BE REFINISHED OR ARE TO SERVE AS SUBSTRATE FOR THE

ATTACHMENT OR APPLICATION OF NEW MATERIALS OR CONSTRUCTION, PREPARE OR ALTER THE

EXISTING SURFACES AS NECESSARY TO PROPERLY ACCOMMODATE THE NEW MATERIALS.

O. FIELD VERIFY SIZES AND DIMENSIONS OF ALL EXISTING UTILITIES THAT IMPACT THE NEW WORK.

DETERMINE THE SIZE AND LOCATION THE PENETRATIONS FROM THE EXISTING UTILITIES WITHIN THE NEW

WORK. SEAL TIGHT TO ALL PENETRATIONS AND CAULK.

P. PENETRATIONS THROUGH EXISTING FIRE RATED CONSTRUCTION MUST BE PROPERLY CLOSED AND FIRE

SAFE'D TO ACHIEVE THE REQUIRED FIRE RATING BY THE END OF CONSTRUCTION OPERATIONS FOR EACH

DAY.

Q. NEW HOLES IN EXISTING ROOF STRUCTURES FOR NEW WORK MUST BE COORDINATED WITH THE

EXISTING STRUCTURE SO THAT CRITICAL STRUCTURAL MEMBERS ARE NOT DAMAGED.

R. UNLESS OTHERWISE NOTED, THE CONTRACTOR IS RESPONSIBLE FOR VERIFYING ALL EXISTING

SALVAGED STOCK BEFORE ORDERING NEW MATERIAL.

E X I S T I N G F A C I L I T I E S:

A. ALL WORK SHALL BE DONE IN ACCORDANCE WITH APPLICABLE LOCAL, STATE AND FEDERAL AUTHORITIES, CODES, RULES AND REGULATIONS.

B. THESE DOCUMENTS SHOW THE MINIMUM CONSTRUCTION REQUIREMENTS AND THE MINIMUM QUALITY OF

WORK EXPECTED. MORE STRINGENT REQUIREMENTS STIPULATED WITHIN RELEVANT MANUFACTURER’S

INSTALLATION INSTRUCTIONS WILL SUPERSEDE.

C. ANY UNFORESEEN OR UNCLEAR CONDITIONS SHALL BE REPORTED TO THE C.O.R. PRIOR TO PROCEEDING

WITH WORK.

D. ANY CONFLICTS WITHIN THE DRAWINGS, BETWEEN THE DRAWINGS AND THE SPECIFICATIONS, OR

BETWEEN THE DRAWINGS AND THE ACTUAL CONDITIONS AT THE SITE, ARE TO BE BROUGHT TO THE

IMMEDIATE ATTENTION OF THE C.O.R. THE CONTRACTOR SHALL NOT PROCEED WITH WORK UNTIL

WRITTEN CLARIFICATION FROM THE ARCHITECT/ENGINEER IS RECEIVED.

E. UNLESS OTHERWISE NOTED, ALL MATERIALS AND EQUIPMENT SHALL BE INSTALLED PER THE APPLICABLE

PROVISIONS OF THESE DOCUMENTS AND THE MANUFACTURER’S INSTRUCTIONS.

F. ALL MATERIALS USED SHALL BE NEW UNLESS OTHERWISE NOTED AND/OR OF A QUALITY TO MEET OR

EXCEED ALL APPLICABLE INDUSTRY STANDARDS. WHERE SPECIFIED PRODUCTS OR MANUFACTURERS

ARE NOT NOTED, THE CONTRACTOR IS REQUIRED TO NOTIFY THE ARCHITECT TO OBTAIN A MINIMUM

STANDARD OF QUALITY.

G. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR ALL MEANS, METHODS AND TECHNIQUES FOR

CONSTRUCTION.

H. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR JOB-SITE SAFETY INCLUDING THE ADHERENCE TO

OSHA REGULATIONS.

I. ALL ELECTRICAL AND MECHANICAL WORK SHALL BE PERFORMED BY PERSONNEL LICENSED IN THE STATE

WHERE THIS PROJECT IS LOCATED.

J. REMOVE ALL DEBRIS PROPERLY FROM THE SITE. LOAD DEBRIS DIRECTLY ONTO TRUCKS FOR REMOVAL.

DISPOSE OF DEBRIS LEGALLY. DO NOT BURN DEBRIS ON THE SITE. DO NOT ALLOW DEBRIS TO ENTER

SEWERS. DO NOT ALLOW PILED DEBRIS TO ENDANGER STRUCTURES, BLOCK EXISTS OR ROADWAYS.

COMBUSTIBLE WASTE WHICH COULD CREATE A FIRE HAZARD SHALL NOT BE PERMITTED TO ACCUMULATE

IN OR AROUND THE CONSTRUCTION SITE.

K. COORDINATE ALL WORK WITH ALL OTHER DISCIPLINES, INCLUDING, EXACT SIZE AND LOCATION OF ALL

ROOF AND FLOOR OPENINGS SHOWN ON ARCHITECTURAL DRAWINGS SHALL BE VERIFIED WITH THE

ASSOCIATED SUB-CONTRACTORS PRIOR TO CONSTRUCTION.

L. DO NOT SCALE DRAWINGS. DIMENSIONS SHALL GOVERN. ALL PLAN DIMENSIONS ARE TAKEN TO FINISH

FACE OF CONSTRUCTION.

M. ALL CONCEALED WOOD SHALL BE FIRE RETARDANT TREATED.

N. SEAL CONSTRUCTION TIGHT TO ALL PENETRATIONS AND APPLY SEALANT.

O. ALL PENETRATIONS THROUGH FIRE RATED CONSTRUCTION MUST BE FIRE SAFE'D IN ACCORDANCE WITH

THE SPECIFICATIONS. IF FLOOR OR RATED WALL PENETRATIONS CANNOT BE FIRESTOPPED AT THE END

OF THE WORK SHIFT DUE TO THE NEED TO PULL ADDITIONAL CABLES, TEMPORARY FIRESTOPPING

COMPOSED OF MINERAL WOOL SHOULD BE INSTALLED IN THE PENETRATION TO PROVIDE PROTECTION

AGAINST FIRE/SMOKE SPREAD THROUGH THE UNSEALED PENETRATION.

P. THE CONTRACTOR IS RESPONSIBLE FOR COORDINATING ALL EQUIPMENT INSTALLATION AND VERIFYING

ALL REQUIRED ROUGH OPENINGS, AND ROUGH-IN DIMENSIONS WITH THE EQUIPMENT MANUFACTURER, AND C.O.R. PRIOR TO CONSTRUCTION.

Q. REFER TO SHEET AE601 FOR SCHEDULES AND PARTITION TYPES.

N E W W O R K:

SHEET NAMING EXAMPLE:

BUILDING NUMBER

DISCIPLINE

SHEET TYPE

FLOOR NUMBER

ZONE LOCATION ON FLOOR

100-AE101.1

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:3

:3

P

M

GI000.3

COVER SHEET - VOL. 3

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CAMPUS

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N.T.S.Scale:

VICINITY MAP

No. Revisions: Date:

BID DOCUMENTS 07/07/2023

SHEET INDEX

ARCHITECTURE

001-AE100 OVERALL BASMENT FLOOR PLAN

001-AE100.1 BASEMENT FLOOR PLAN - ZONE 1

001-AE101 OVERALL FIRST FLOOR PLAN

001-AE101.1 FIRST FLOOR PLAN - ZONE 1

001-AE101.2 FIRST FLOOR PLAN - ZONE 2

001-AE102 OVERALL SECOND FLOOR PLAN

001-AE102.1 SECOND FLOOR PLAN - ZONE 1

001-AE102.2 SECOND FLOOR PLAN - ZONE 2

003-AE101 OVERALL FIRST FLOOR PLAN

003-AE101.1 FIRST FLOOR PLAN - ZONE 1

007-AE101 OVERALL FIRST FLOOR PLAN

009-AE101 OVERALL FIRST FLOOR PLAN

018-AE101 OVERALL FIRST FLOOR PLAN

018-AE102 OVERALL SECOND FLOOR PLAN

020-AE102 OVERALL FLOOR PLANS

021-AE101 FIRST FLOOR PLAN

023-AE101 OVERALL FIRST FLOOR

024-AE100 OVERALL BASEMENT FLOOR PLAN

024-AE100.1 BASEMENT TR PLANS

024-AE101 OVERALL FIRST FLOOR PLAN

024-AE101.1 FIRST FLOOR ZONE 1 - TR PLANS

024-AE102 OVERALL SECOND FLOOR PLAN

024-AE102.1 SECOND FLOOR PLAN - TR PLANS

025-AE100 OVERALL FLOOR PLAN

026-AE100 OVERALL BASEMENT FLOOR PLAN

026-AE100.1 BASEMENT FLOOR PLAN - TR PLANS

026-AE101 OVERALL FIRST FLOOR PLAN

026-AE101.1 FIRST FLOOR PLAN - TR PLANS

026-AE102 OVERALL SECOND FLOOR PLAN

026-AE102.1 SECOND FLOOR PLAN - TR PLANS

027-AE100 OVERALL BASEMENT FLOOR PLAN

027-AE100.1 BASEMENT FLOOR ZONE 1 - TR PLANS

027-AE101 OVERALL FIRST FLOOR PLAN

027-AE101.1 FIRST FLOOR ZONE 1 - TR PLANS

027-AE102 OVERALL SECOND FLOOR PLAN

027-AE102.1 SECOND FLOOR ZONE 1 - TR PLANS

028-AE102 OVERALL SECOND FLOOR

030-AE100 OVERALL BASEMENT FLOOR PLAN

030-AE100.1 BASEMENT FLOOR PLAN - ZONE 1

030-AE101 OVERALL FIRST FLOOR PLAN

030-AE101.1 FIRST FLOOR PLAN - TR PLANS

030-AE102 OVERALL SECOND FLOOR PLAN

030-AE102.1 SECOND FLOOR PLAN - TR PLANS

N.T.S.Scale:

VICINITY MAP

SHEET INDEX

GENERAL

GI000.3 COVER SHEET - VOL. 3

UP UP

DN

ZONE 1

ZONE 3ZONE 2

ZONE 5ZONE 4

001-AE100.1

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:1

P

M

001-AE100

OVERALL BASMENT FLOOR PLAN

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N

1" = 10'-0"

B01 - BASEMENT FLOOR PLAN - OVERALL

No. Revisions: Date:

BID DOCUMENTS 07/07/2023

K

001-AE100.1

Training Room

BB103

Game Room

BC100A

Storage

BB102

TELECOMM. ROOM

BB105

Cio Equipment Storage

BB101

Stair

S1-0

Corridor

CB6

Corridor

CB5

Engineering Room

BB104

Mechanical

BB106

Tele Clos

BB104A

Toilet

BB107

Corridor

CB4

Stair

S2-0Storage

BB100

Corridor

CB1

Storage

BB101A

2 - 5

TELECOMM. ROOM

BB105

BB105

TELECOMM. ROOM

BB105

128 SF

TELECOMM. ROOM

BB105

BB105

TELECOMM. ROOM

BB105

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S

G E N E R A L C O N S T R U C T I O N N O T E S

A. REFER TO NEW WORK ARCHITECTURAL FLOOR PLANS FOR PARTITION TYPE DESIGNATIONS. SEE PARTITION TYPES ON

SHEET AE601.

B. ALL GYPSUM BOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. PARTITION TYPES INDICATED ARE CONTINUOUS TO A CORNER OR AN INTERSECTING PARTITION, UNLESS INDICATED OTHERWISE. WHERE PARTITIONS OF DIFFERENT THICKNESSES MEET, MAINTAIN A FLUSH SURFACE ON THE SIDE WHERE

FACES ARE STRAIGHT AND CONTINUOUS, UNLESS NOTED OTHERWISE.

D. ALL COLD-FORMED STEEL FRAMING SHALL BE 20 GUAGE OR HEAVIER.

E. EDGES OF GYPSUM BOARD LEFT EXPOSED TO VIEW, OR ABUTTING DISSIMILAR MATERIAL, IS TO BE FINISHED WITH METAL "L"

BEAD TRIM AND COMPOUND UNLESS NOTED OTHERWISE.

F. ALL FIRE RATED WALL AND FLOOR PENETRATION MUST COMPLY WITH ASTM-E814

G. ALL DOOR OPENINGS SHALL BE 4" FROM A PERPENDICULAR PARTITION TO OUTSIDE FACE OF FRAME, UNLESS NOTED OR

DETAILED OTHERWISE.

H. ALL PARTITIONS, INCL. STUDS, BOARD, ETC. SHALL EXTEND FROM TOP OF FLOOR SLAB TO UNDERSIDE OF CONCRETE SLAB

ABOVE UNLESS OTHERWISE NOTED.

I. CONTRACTOR SHALL CLOSE OFF ANY VOIDS LEFT AS A RESULT OF ANY REMOVALS AND NEW CONSTRUCTION, AS WELL AS INFILL ANY EXISTING VOIDS IN NEWLY DESIGNATED FIRE RATED PARTITIONS. ALL PATCHES SHALL MATCH AND ALIGN WITH

SURROUNDING MATERIALS AND SHALL BE IN ACCORDANCE WITH NFPA CODE.

J. CONTRACTOR SHALL SEAL AROUND ALL M.E.P. PENETRATIONS OR OPENINGS, RESULTING FROM M.E.P. INSTALLATIONS INCLUDING BUT NOT LIMITED TO THE SLAB AND PARTITION WALLS ABOVE AND BELOW CEILINGS.

K. NO EXISTING FIREPROOFING IS TO BE REMOVED FROM EXISTING BUILDING STRUCTURE FOR ANY NEW INSTALLATION FOR

ANY REASON.

L. LABEL ALL RATED PARTITIONS (FIRE & SMOKE) ABOVE THE CEILING, ON BOTH SIDES OF THE WALL.

M. PROVIDE A MINIMUM OF ONE STUD SEPARATION BETWEEN OUTLET BOXES AND OTHER PENETRATIONS OCCURRING AT

OPPOSITE FACE OF WALLS.

N. PROVIDE CONTINUOUS NON-HARDENING ACOUSTICAL SEALANT AT TOP, SIDES AND EDGES OF BOTH SIDES OF WALL AT ALL NON-RATED GYPSUM BOARD PARTITIONS SCHEDULED TO RECEIVE SOUND ATTENUATION BLANKETS.

O. ALL PENETRATIONS AT NON-RATED WALLS SHALL BE SLEEVED AND PACKED AIRTIGHT WITH SAFING INSULATION AND SEALANT. ALL JOINT OF GYPSUM BOARD PANELS SHALL BE STAGGERED, TAPED, AND SEALED. FRAMING TO 1/2" +/-

CLEARANCE AT PERIMETER OF MECHANICAL DUCTWORK.

P. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

Q. COLD-FORMED STEEL (CFS) FRAMING SUPPLIER SHALL PROVIDE ENGINEERED DRAWINGS.

R. PROVIDE DOUBLE CFS FRAMING STUDS AT JAMBS OF DOOR AND FIXED GLASS FRAMES, AT OPEN PARTITION ENDS, AND WHERE PARTITION IS TO RECEIVE WALL MOUNTED SHELVES, CASEWORK, PLUMBING FIXTURES, ETC.

S. PROVIDE ADDITIONAL BRACING AS REQUIRED AT ALL CFS FRAMING STUD INSTALLATIONS EXCEEDING STUD MANUFACTURER

REQUIREMENTS FOR MAXIMUM ALLOWED HEIGHT AND DEFLECTION.

T. REFER TO MECHANICAL DRAWINGS FOR QUANTITY AND TYPE OF DIFFUSERS, RETURN AIR GRILLES, AND EXHAUST GRILLES.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

U. REFER TO ELECTRICAL DRAWINGS FOR QUANTITY AND TYPES OF LIGHTS, SPEAKERS, DETECTORS, POWER OUTLETS, ETC.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

V. BUILD PARTITIONS IN ACCORDANCE WITH PARTITION TYPE AND DESIGN REFERENCED. REFERENCES ARE TO LATEST EDITION OF GYPSUM ASSOCIATION (GA) FIRE RESISTANCE DESIGN MANUAL, OR TO UNDERWRITERS LABORATORY (UL) FIRE

RESISTANCE DIRECTORY.

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:2

P

M

001-AE100.1

BASEMENT FLOOR PLAN - ZONE 1

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

1/8" = 1'-0"

B01 - BASEMENT FLOOR PLAN - ZONE 1

1/4" = 1'-0"

B01 - BASEMENT FLOOR PLAN - DEMO

1/4" = 1'-0"

B01 - BASEMENT REFLECTED CEILING PLAN - DEMO

1/4" = 1'-0"

B01 - BASEMENT FLOOR PLAN - NEW WORK

1/4" = 1'-0"

B01 - BASEMENT REFLECTED CEILING PLAN - NEW WORK

D R A W I N G N O T E S :

1 REMOVE EXISTING DOOR FRAME, DOOR, AND HARDWARE; TURN DOOR AND HARDWARE OVER TO VA TO ADD TO

EXISTING STOCK.

2 REMOVE EXISTING CARPET AND MASTIC MATERIAL FROM FLOOR. CLEAN AND PREPARE FLOOR FOR INSTALLATION OF

ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT.

3 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

4 EXISTING WALL MOUNTED PLYWOOD TO REMAIN, TYPICAL.

5 ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT - SEE HATCHED AREA.

6 WINDOW SECURITY BARS - REFER TO DETAILS ON SHEET AE601 FOR BASIS OF DESIGN AND DETAILS.

7 REMOVE VINYL WALL BASE ALONG THIS WALL.

8 VINYL WALL BASE ALONG WALL, MATCH EXISTING BASE IN ROOM.

9 WALL MOUNTED FIRE EXTINGUISHER CABINET. PROVIDE NEW 10LB. CLASS C FIRE EXTINGUISHER FOR CABINET. SEE

FIRE CABINET ELEVATION ON SHEET GI001 FOR INSTALLATION HEIGHT.

10 REMOVE ALL PAINT AND DEBRIS FROM WALL. AREA IDENTIFIED BY DASHED LINE.

11 PAINT WALLS - REFER TO FINISH SCHEDULE

12 NO CEILING IN THIS AREA

13 REMOVE CEILING SYSTEMS AND SUPPORTS

14 EXISTING CARD READER TO REMAIN

15 NEW WALL - REFER TO AE601 FOR PARTITION TYPE DETAIL.

DN DNDN

ZONE 1

ZONE 3ZONE 2

ZONE 5ZONE 4

001-AE101.1

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:3

P

M

001-AE101

OVERALL FIRST FLOOR PLAN

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

1" = 10'-0"

B01 - FIRST FLOOR PLAN - OVERALL

UP

KToilet

Voucher Examiner & Employee Travel

Conference Room

Contract Specialist

Contract Spec Intern

Supply Tech

Chief Acquisitions/ Contracting

Contract Liason

Contract Specialist

Contract Specialists

Admin Support Assist

Chief Logistics

Chief Inventory Supply Support

Inventory Management Spec

Item Manager

Item Manager

Item Manager

Xerox/supplies

Toilet

Files Storage

TR

Corridor

1C002

Corridor

1C006

Stair

S1-1

001-AE101.2

22 - 5

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S

G E N E R A L C O N S T R U C T I O N N O T E S

A. REFER TO NEW WORK ARCHITECTURAL FLOOR PLANS FOR PARTITION TYPE DESIGNATIONS. SEE PARTITION TYPES ON

SHEET AE601.

B. ALL GYPSUM BOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. PARTITION TYPES INDICATED ARE CONTINUOUS TO A CORNER OR AN INTERSECTING PARTITION, UNLESS INDICATED OTHERWISE. WHERE PARTITIONS OF DIFFERENT THICKNESSES MEET, MAINTAIN A FLUSH SURFACE ON THE SIDE WHERE

FACES ARE STRAIGHT AND CONTINUOUS, UNLESS NOTED OTHERWISE.

D. ALL COLD-FORMED STEEL FRAMING SHALL BE 20 GUAGE OR HEAVIER.

E. EDGES OF GYPSUM BOARD LEFT EXPOSED TO VIEW, OR ABUTTING DISSIMILAR MATERIAL, IS TO BE FINISHED WITH METAL "L"

BEAD TRIM AND COMPOUND UNLESS NOTED OTHERWISE.

F. ALL FIRE RATED WALL AND FLOOR PENETRATION MUST COMPLY WITH ASTM-E814

G. ALL DOOR OPENINGS SHALL BE 4" FROM A PERPENDICULAR PARTITION TO OUTSIDE FACE OF FRAME, UNLESS NOTED OR

DETAILED OTHERWISE.

H. ALL PARTITIONS, INCL. STUDS, BOARD, ETC. SHALL EXTEND FROM TOP OF FLOOR SLAB TO UNDERSIDE OF CONCRETE SLAB

ABOVE UNLESS OTHERWISE NOTED.

I. CONTRACTOR SHALL CLOSE OFF ANY VOIDS LEFT AS A RESULT OF ANY REMOVALS AND NEW CONSTRUCTION, AS WELL AS INFILL ANY EXISTING VOIDS IN NEWLY DESIGNATED FIRE RATED PARTITIONS. ALL PATCHES SHALL MATCH AND ALIGN WITH

SURROUNDING MATERIALS AND SHALL BE IN ACCORDANCE WITH NFPA CODE.

J. CONTRACTOR SHALL SEAL AROUND ALL M.E.P. PENETRATIONS OR OPENINGS, RESULTING FROM M.E.P. INSTALLATIONS INCLUDING BUT NOT LIMITED TO THE SLAB AND PARTITION WALLS ABOVE AND BELOW CEILINGS.

K. NO EXISTING FIREPROOFING IS TO BE REMOVED FROM EXISTING BUILDING STRUCTURE FOR ANY NEW INSTALLATION FOR

ANY REASON.

L. LABEL ALL RATED PARTITIONS (FIRE & SMOKE) ABOVE THE CEILING, ON BOTH SIDES OF THE WALL.

M. PROVIDE A MINIMUM OF ONE STUD SEPARATION BETWEEN OUTLET BOXES AND OTHER PENETRATIONS OCCURRING AT

OPPOSITE FACE OF WALLS.

N. PROVIDE CONTINUOUS NON-HARDENING ACOUSTICAL SEALANT AT TOP, SIDES AND EDGES OF BOTH SIDES OF WALL AT ALL NON-RATED GYPSUM BOARD PARTITIONS SCHEDULED TO RECEIVE SOUND ATTENUATION BLANKETS.

O. ALL PENETRATIONS AT NON-RATED WALLS SHALL BE SLEEVED AND PACKED AIRTIGHT WITH SAFING INSULATION AND SEALANT. ALL JOINT OF GYPSUM BOARD PANELS SHALL BE STAGGERED, TAPED, AND SEALED. FRAMING TO 1/2" +/-

CLEARANCE AT PERIMETER OF MECHANICAL DUCTWORK.

P. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

Q. COLD-FORMED STEEL (CFS) FRAMING SUPPLIER SHALL PROVIDE ENGINEERED DRAWINGS.

R. PROVIDE DOUBLE CFS FRAMING STUDS AT JAMBS OF DOOR AND FIXED GLASS FRAMES, AT OPEN PARTITION ENDS, AND WHERE PARTITION IS TO RECEIVE WALL MOUNTED SHELVES, CASEWORK, PLUMBING FIXTURES, ETC.

S. PROVIDE ADDITIONAL BRACING AS REQUIRED AT ALL CFS FRAMING STUD INSTALLATIONS EXCEEDING STUD MANUFACTURER

REQUIREMENTS FOR MAXIMUM ALLOWED HEIGHT AND DEFLECTION.

T. REFER TO MECHANICAL DRAWINGS FOR QUANTITY AND TYPE OF DIFFUSERS, RETURN AIR GRILLES, AND EXHAUST GRILLES.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

U. REFER TO ELECTRICAL DRAWINGS FOR QUANTITY AND TYPES OF LIGHTS, SPEAKERS, DETECTORS, POWER OUTLETS, ETC.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

V. BUILD PARTITIONS IN ACCORDANCE WITH PARTITION TYPE AND DESIGN REFERENCED. REFERENCES ARE TO LATEST EDITION OF GYPSUM ASSOCIATION (GA) FIRE RESISTANCE DESIGN MANUAL, OR TO UNDERWRITERS LABORATORY (UL) FIRE

RESISTANCE DIRECTORY.

Files Storage

TR

Files Storage

98 SF

TR

5 6

8 9

Files Storage

98 SF

TR

TR

Files Storage

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:5

P

M

001-AE101.2

FIRST FLOOR PLAN - ZONE 2

07/07/2023 Checker Author

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

1/8" = 1'-0"

B01 - FIRST FLOOR PLAN - ZONE 2

D R A W I N G N O T E S :

1 REMOVE WALL

2 NO CEILING IN THIS AREA

3 WALL MOUNTED FIRE EXTINGUISHER CABINET. PROVIDE NEW 10LB. CLASS C FIRE EXTINGUISHER FOR CABINET. SEE

FIRE CABINET ELEVATION ON SHEET GI001 FOR INSTALLATION HEIGHT.

4 ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT - SEE HATCHED AREA.

5 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

6 WINDOW SECURITY BARS - REFER TO DETAILS ON SHEET AE601 FOR BASIS OF DESIGN AND DETAILS.

7 REMOVE CEILING GRID AND ACOUSTICAL TILES. LEAVE CEILING GRID SUPPORTS FOR INSTALLATION OF NEW GRID AND

TILES.

8 PAINT WALLS - REFER TO FINISH SCHEDULE

9 VINYL WALL BASE ALONG WALL - MATCH EXISTING BASE IN ROOM.

10 NEW CEILING COMPONENTS TO TIE EXISTING CEILING SYSTEM TO NEW WALL - MATCH EXISTING GRID COMPONENTS

AND ACOUSTICAL CEILING TILES

11 EXISTING CARD READER TO REMAIN

12 NEW WALL - REFER TO AE601 FOR PARTITION TYPE DETAIL.

1/4" = 1'-0"

B01 - FIRST FLOOR PLAN - DEMO

1/4" = 1'-0"

B01 - FIRST FLOOR PLAN - NEW WORK

1/4" = 1'-0"

B01 - FIRST FLOOR REFLECTED CEILING PLAN - NEW WORK

1/4" = 1'-0"

B01 - FIRST FLOOR REFLECTED CEILING PLAN - DEMO

DN DNDN

001-AE101.1

Risk Manager

Performance Measure Coordinator

Patient Safety

External Review Manager

Contracting Liason Office

Toilet

Filing Supplies

Utilization Nurse

HAC

Performance Measure Coordinator

Program Support Assistant

Systems Design Coordinator

HAC

Copy Room

Break Room

Quality Improvement Facilitator

Quality Manager

QI Program Asst

Waiting

1L001

Corridor

1C002

Waiting

1L002

Corridor

1C007

Stair

S2-1

Stair

S1-1

2 - 5

Eeo Manage

Eeo Manage

116 SF

TR

1L002

Eeo Manage

TR

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S

G E N E R A L C O N S T R U C T I O N N O T E S

A. REFER TO NEW WORK ARCHITECTURAL FLOOR PLANS FOR PARTITION TYPE DESIGNATIONS. SEE PARTITION TYPES ON

SHEET AE601.

B. ALL GYPSUM BOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. PARTITION TYPES INDICATED ARE CONTINUOUS TO A CORNER OR AN INTERSECTING PARTITION, UNLESS INDICATED OTHERWISE. WHERE PARTITIONS OF DIFFERENT THICKNESSES MEET, MAINTAIN A FLUSH SURFACE ON THE SIDE WHERE

FACES ARE STRAIGHT AND CONTINUOUS, UNLESS NOTED OTHERWISE.

D. ALL COLD-FORMED STEEL FRAMING SHALL BE 20 GUAGE OR HEAVIER.

E. EDGES OF GYPSUM BOARD LEFT EXPOSED TO VIEW, OR ABUTTING DISSIMILAR MATERIAL, IS TO BE FINISHED WITH METAL "L"

BEAD TRIM AND COMPOUND UNLESS NOTED OTHERWISE.

F. ALL FIRE RATED WALL AND FLOOR PENETRATION MUST COMPLY WITH ASTM-E814

G. ALL DOOR OPENINGS SHALL BE 4" FROM A PERPENDICULAR PARTITION TO OUTSIDE FACE OF FRAME, UNLESS NOTED OR

DETAILED OTHERWISE.

H. ALL PARTITIONS, INCL. STUDS, BOARD, ETC. SHALL EXTEND FROM TOP OF FLOOR SLAB TO UNDERSIDE OF CONCRETE SLAB

ABOVE UNLESS OTHERWISE NOTED.

I. CONTRACTOR SHALL CLOSE OFF ANY VOIDS LEFT AS A RESULT OF ANY REMOVALS AND NEW CONSTRUCTION, AS WELL AS INFILL ANY EXISTING VOIDS IN NEWLY DESIGNATED FIRE RATED PARTITIONS. ALL PATCHES SHALL MATCH AND ALIGN WITH

SURROUNDING MATERIALS AND SHALL BE IN ACCORDANCE WITH NFPA CODE.

J. CONTRACTOR SHALL SEAL AROUND ALL M.E.P. PENETRATIONS OR OPENINGS, RESULTING FROM M.E.P. INSTALLATIONS INCLUDING BUT NOT LIMITED TO THE SLAB AND PARTITION WALLS ABOVE AND BELOW CEILINGS.

K. NO EXISTING FIREPROOFING IS TO BE REMOVED FROM EXISTING BUILDING STRUCTURE FOR ANY NEW INSTALLATION FOR

ANY REASON.

L. LABEL ALL RATED PARTITIONS (FIRE & SMOKE) ABOVE THE CEILING, ON BOTH SIDES OF THE WALL.

M. PROVIDE A MINIMUM OF ONE STUD SEPARATION BETWEEN OUTLET BOXES AND OTHER PENETRATIONS OCCURRING AT

OPPOSITE FACE OF WALLS.

N. PROVIDE CONTINUOUS NON-HARDENING ACOUSTICAL SEALANT AT TOP, SIDES AND EDGES OF BOTH SIDES OF WALL AT ALL NON-RATED GYPSUM BOARD PARTITIONS SCHEDULED TO RECEIVE SOUND ATTENUATION BLANKETS.

O. ALL PENETRATIONS AT NON-RATED WALLS SHALL BE SLEEVED AND PACKED AIRTIGHT WITH SAFING INSULATION AND SEALANT. ALL JOINT OF GYPSUM BOARD PANELS SHALL BE STAGGERED, TAPED, AND SEALED. FRAMING TO 1/2" +/-

CLEARANCE AT PERIMETER OF MECHANICAL DUCTWORK.

P. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

Q. COLD-FORMED STEEL (CFS) FRAMING SUPPLIER SHALL PROVIDE ENGINEERED DRAWINGS.

R. PROVIDE DOUBLE CFS FRAMING STUDS AT JAMBS OF DOOR AND FIXED GLASS FRAMES, AT OPEN PARTITION ENDS, AND WHERE PARTITION IS TO RECEIVE WALL MOUNTED SHELVES, CASEWORK, PLUMBING FIXTURES, ETC.

S. PROVIDE ADDITIONAL BRACING AS REQUIRED AT ALL CFS FRAMING STUD INSTALLATIONS EXCEEDING STUD MANUFACTURER

REQUIREMENTS FOR MAXIMUM ALLOWED HEIGHT AND DEFLECTION.

T. REFER TO MECHANICAL DRAWINGS FOR QUANTITY AND TYPE OF DIFFUSERS, RETURN AIR GRILLES, AND EXHAUST GRILLES.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

U. REFER TO ELECTRICAL DRAWINGS FOR QUANTITY AND TYPES OF LIGHTS, SPEAKERS, DETECTORS, POWER OUTLETS, ETC.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

V. BUILD PARTITIONS IN ACCORDANCE WITH PARTITION TYPE AND DESIGN REFERENCED. REFERENCES ARE TO LATEST EDITION OF GYPSUM ASSOCIATION (GA) FIRE RESISTANCE DESIGN MANUAL, OR TO UNDERWRITERS LABORATORY (UL) FIRE

RESISTANCE DIRECTORY.

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:4

P

M

001-AE101.1

FIRST FLOOR PLAN - ZONE 1

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

1/8" = 1'-0"

B01 - FIRST FLOOR PLAN - ZONE 1

1/4" = 1'-0"

B01 - FIRST FLOOR PLAN - DEMO

1/4" = 1'-0"

B01 - FIRST FLOOR PLAN - NEW WORK

D R A W I N G N O T E S :

1 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

2 REMOVE EXISTING CARPET AND MASTIC MATERIAL FROM FLOOR. CLEAN AND PREPARE FLOOR FOR INSTALLATION OF

ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT.

3 REMOVE CEILING SYSTEMS AND SUPPORTS

4 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

5 ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT - SEE HATCHED AREA.

6 WINDOW SECURITY BARS - REFER TO DETAILS ON SHEET AE601 FOR BASIS OF DESIGN AND DETAILS.

7 NO CEILING IN THIS AREA

8 REMOVED AND REPLACE FRAME AND LOCK SET AS REQUIRED FOR CARD READER. REUSE REMAINING HARDWARE

9 WALL MOUNTED FIRE EXTINGUISHER CABINET. PROVIDE NEW 10LB. CLASS C FIRE EXTINGUISHER FOR CABINET. SEE

FIRE CABINET ELEVATION ON SHEET GI001 FOR INSTALLATION HEIGHT.

10 REMOVE PACKAGED THERMAL UNIT

11 CARD READER - REFER TO ELECTRICAL DRAWINGS1/4" = 1'-0"

B01 - FIRST FLOOR REFLECTED CEILING PLAN - DEMO

1/4" = 1'-0"

B01 - FIRST FLOOR REFLECTED CEILING PLAN - NEW WORK

DN

UP

D

EM

D

D

EM

D

EM

D

EM

D

D

D

EM

EM

D

D

D

EM

E M

D

D

E M

D

ZONE 1

ZONE 3ZONE 2

ZONE 5ZONE 4

001-AE102.1

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:0

P

M

001-AE102

OVERALL SECOND FLOOR PLAN

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N

1" = 10'-0"

B01 - SECOND FLOOR PLAN - OVERALL

K

Toilet

Regional Counsel Library

Hr Assistants

Copy/mail Room

Hrm Office

Intern Office

Hrm Office

Resource Room

Hrm Specalists

Vet Pro

Hrm Office

Hrm Office

Hrm Office

Tele Clos

Employee Resources

Regional Counsel Office

224A

Corridor

2C5

Regional Counsel Office

224B

Tele Clos

Stair

S1-2

Corridor

2C003

302 SF

Corridor

2C002

HMR ASSISTANT

238 001-AE102.2

22 - 5

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S

G E N E R A L C O N S T R U C T I O N N O T E S

A. REFER TO NEW WORK ARCHITECTURAL FLOOR PLANS FOR PARTITION TYPE DESIGNATIONS. SEE PARTITION TYPES ON

SHEET AE601.

B. ALL GYPSUM BOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. PARTITION TYPES INDICATED ARE CONTINUOUS TO A CORNER OR AN INTERSECTING PARTITION, UNLESS INDICATED OTHERWISE. WHERE PARTITIONS OF DIFFERENT THICKNESSES MEET, MAINTAIN A FLUSH SURFACE ON THE SIDE WHERE

FACES ARE STRAIGHT AND CONTINUOUS, UNLESS NOTED OTHERWISE.

D. ALL COLD-FORMED STEEL FRAMING SHALL BE 20 GUAGE OR HEAVIER.

E. EDGES OF GYPSUM BOARD LEFT EXPOSED TO VIEW, OR ABUTTING DISSIMILAR MATERIAL, IS TO BE FINISHED WITH METAL "L"

BEAD TRIM AND COMPOUND UNLESS NOTED OTHERWISE.

F. ALL FIRE RATED WALL AND FLOOR PENETRATION MUST COMPLY WITH ASTM-E814

G. ALL DOOR OPENINGS SHALL BE 4" FROM A PERPENDICULAR PARTITION TO OUTSIDE FACE OF FRAME, UNLESS NOTED OR

DETAILED OTHERWISE.

H. ALL PARTITIONS, INCL. STUDS, BOARD, ETC. SHALL EXTEND FROM TOP OF FLOOR SLAB TO UNDERSIDE OF CONCRETE SLAB

ABOVE UNLESS OTHERWISE NOTED.

I. CONTRACTOR SHALL CLOSE OFF ANY VOIDS LEFT AS A RESULT OF ANY REMOVALS AND NEW CONSTRUCTION, AS WELL AS INFILL ANY EXISTING VOIDS IN NEWLY DESIGNATED FIRE RATED PARTITIONS. ALL PATCHES SHALL MATCH AND ALIGN WITH

SURROUNDING MATERIALS AND SHALL BE IN ACCORDANCE WITH NFPA CODE.

J. CONTRACTOR SHALL SEAL AROUND ALL M.E.P. PENETRATIONS OR OPENINGS, RESULTING FROM M.E.P. INSTALLATIONS INCLUDING BUT NOT LIMITED TO THE SLAB AND PARTITION WALLS ABOVE AND BELOW CEILINGS.

K. NO EXISTING FIREPROOFING IS TO BE REMOVED FROM EXISTING BUILDING STRUCTURE FOR ANY NEW INSTALLATION FOR

ANY REASON.

L. LABEL ALL RATED PARTITIONS (FIRE & SMOKE) ABOVE THE CEILING, ON BOTH SIDES OF THE WALL.

M. PROVIDE A MINIMUM OF ONE STUD SEPARATION BETWEEN OUTLET BOXES AND OTHER PENETRATIONS OCCURRING AT

OPPOSITE FACE OF WALLS.

N. PROVIDE CONTINUOUS NON-HARDENING ACOUSTICAL SEALANT AT TOP, SIDES AND EDGES OF BOTH SIDES OF WALL AT ALL NON-RATED GYPSUM BOARD PARTITIONS SCHEDULED TO RECEIVE SOUND ATTENUATION BLANKETS.

O. ALL PENETRATIONS AT NON-RATED WALLS SHALL BE SLEEVED AND PACKED AIRTIGHT WITH SAFING INSULATION AND SEALANT. ALL JOINT OF GYPSUM BOARD PANELS SHALL BE STAGGERED, TAPED, AND SEALED. FRAMING TO 1/2" +/-

CLEARANCE AT PERIMETER OF MECHANICAL DUCTWORK.

P. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

Q. COLD-FORMED STEEL (CFS) FRAMING SUPPLIER SHALL PROVIDE ENGINEERED DRAWINGS.

R. PROVIDE DOUBLE CFS FRAMING STUDS AT JAMBS OF DOOR AND FIXED GLASS FRAMES, AT OPEN PARTITION ENDS, AND WHERE PARTITION IS TO RECEIVE WALL MOUNTED SHELVES, CASEWORK, PLUMBING FIXTURES, ETC.

S. PROVIDE ADDITIONAL BRACING AS REQUIRED AT ALL CFS FRAMING STUD INSTALLATIONS EXCEEDING STUD MANUFACTURER

REQUIREMENTS FOR MAXIMUM ALLOWED HEIGHT AND DEFLECTION.

T. REFER TO MECHANICAL DRAWINGS FOR QUANTITY AND TYPE OF DIFFUSERS, RETURN AIR GRILLES, AND EXHAUST GRILLES.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

U. REFER TO ELECTRICAL DRAWINGS FOR QUANTITY AND TYPES OF LIGHTS, SPEAKERS, DETECTORS, POWER OUTLETS, ETC.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

V. BUILD PARTITIONS IN ACCORDANCE WITH PARTITION TYPE AND DESIGN REFERENCED. REFERENCES ARE TO LATEST EDITION OF GYPSUM ASSOCIATION (GA) FIRE RESISTANCE DESIGN MANUAL, OR TO UNDERWRITERS LABORATORY (UL) FIRE

RESISTANCE DIRECTORY.

Tele Clos

HMR ASSISTANT

REMOVE FLOORING BOUNDARY

Tele Clos

HMR ASSISTANT

HMR ASSISTANT

Tele Clos

HMR ASSISTANT

Tele Clos

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:3

P

M

001-AE102.2

SECOND FLOOR PLAN - ZONE 2

07/07/2023 Checker Author

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N

1/8" = 1'-0"

B01 - SECOND FLOOR PLAN - ZONE 2

D R A W I N G N O T E S :

1 REMOVE EXISTING CARPET AND MASTIC MATERIAL FROM FLOOR. CLEAN AND PREPARE FLOOR FOR INSTALLATION OF

ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT.

2 REMOVE WALL

3 NEW WALL - REFER TO AE601 FOR PARTITION TYPE DETAIL.

4 ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT - SEE HATCHED AREA.

5 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

6 WINDOW SECURITY BARS - REFER TO DETAILS ON SHEET AE601 FOR BASIS OF DESIGN AND DETAILS.

7 PAINT WALLS - REFER TO FINISH SCHEDULE

8 LEAVE CEILING SUPPORTS IN ADJACENT SPACE TO FUTURE TR. NEW CEILING COMPONENTS TO BE INSTALLED AND TIED

INTO EXISTING CEILING GRID.

9 VINYL WALL BASE ALONG WALL - MATCH EXISTING BASE IN ROOM.

10 WALL MOUNTED FIRE EXTINGUISHER CABINET. PROVIDE NEW 10LB. CLASS C FIRE EXTINGUISHER FOR CABINET. SEE

FIRE CABINET ELEVATION ON SHEET GI001 FOR INSTALLATION HEIGHT.

11 NO CEILING IN THIS AREA

12 NEW CEILING COMPONENTS TO TIE EXISTING CEILING SYSTEM TO NEW WALL - MATCH EXISTING GRID COMPONENTS

AND ACOUSTICAL CEILING TILES

13 EXISTING CARD READER TO REMAIN

1/4" = 1'-0"

B01 - SECOND FLOOR PLAN - DEMO

1/4" = 1'-0"

B01 - SECOND FLOOR PLAN - NEW WORK

1/4" = 1'-0"

B01 - SECOND FLOOR REFLECTED CEILING PLAN - DEMO

1/4" = 1'-0"

B01 - SECOND FLOOR REFLECTED CEILING PLAN - NEW WORK

DN

UP

K

001-AE102.1

22 - 5

Health Systems Spec Pcs

Emergency Preparedness Coordinator

Patient Business Intern

Assistant Patient Business Manager

Customer Service Coordinator

Toilet

Dss Liason

Interior Designer

Conference/Training

Facility Telehealth Coordinator

HAC

Break Room

Training Room

Training Room

Patient Business Service Manager

245A

Heart Code Room

Stair

S1-2

Stair

S2-2

Corridor

2C002

Corridor

2C001 Corridor

2C006

Corridor

2C005

TR

284A

TRAINING ROOM

10' - 5"

R E

M O

V E

F

LO

O

R

IN

G B

O U

N D

A R

Y

TRAINING ROOM

TRAINING ROOM

10' - 0"

TR

284A

284A

11 12

TRAINING ROOM

TRAINING ROOM

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S

G E N E R A L C O N S T R U C T I O N N O T E S

A. REFER TO NEW WORK ARCHITECTURAL FLOOR PLANS FOR PARTITION TYPE DESIGNATIONS. SEE PARTITION TYPES ON

SHEET AE601.

B. ALL GYPSUM BOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. PARTITION TYPES INDICATED ARE CONTINUOUS TO A CORNER OR AN INTERSECTING PARTITION, UNLESS INDICATED OTHERWISE. WHERE PARTITIONS OF DIFFERENT THICKNESSES MEET, MAINTAIN A FLUSH SURFACE ON THE SIDE WHERE

FACES ARE STRAIGHT AND CONTINUOUS, UNLESS NOTED OTHERWISE.

D. ALL COLD-FORMED STEEL FRAMING SHALL BE 20 GUAGE OR HEAVIER.

E. EDGES OF GYPSUM BOARD LEFT EXPOSED TO VIEW, OR ABUTTING DISSIMILAR MATERIAL, IS TO BE FINISHED WITH METAL "L"

BEAD TRIM AND COMPOUND UNLESS NOTED OTHERWISE.

F. ALL FIRE RATED WALL AND FLOOR PENETRATION MUST COMPLY WITH ASTM-E814

G. ALL DOOR OPENINGS SHALL BE 4" FROM A PERPENDICULAR PARTITION TO OUTSIDE FACE OF FRAME, UNLESS NOTED OR

DETAILED OTHERWISE.

H. ALL PARTITIONS, INCL. STUDS, BOARD, ETC. SHALL EXTEND FROM TOP OF FLOOR SLAB TO UNDERSIDE OF CONCRETE SLAB

ABOVE UNLESS OTHERWISE NOTED.

I. CONTRACTOR SHALL CLOSE OFF ANY VOIDS LEFT AS A RESULT OF ANY REMOVALS AND NEW CONSTRUCTION, AS WELL AS INFILL ANY EXISTING VOIDS IN NEWLY DESIGNATED FIRE RATED PARTITIONS. ALL PATCHES SHALL MATCH AND ALIGN WITH

SURROUNDING MATERIALS AND SHALL BE IN ACCORDANCE WITH NFPA CODE.

J. CONTRACTOR SHALL SEAL AROUND ALL M.E.P. PENETRATIONS OR OPENINGS, RESULTING FROM M.E.P. INSTALLATIONS INCLUDING BUT NOT LIMITED TO THE SLAB AND PARTITION WALLS ABOVE AND BELOW CEILINGS.

K. NO EXISTING FIREPROOFING IS TO BE REMOVED FROM EXISTING BUILDING STRUCTURE FOR ANY NEW INSTALLATION FOR

ANY REASON.

L. LABEL ALL RATED PARTITIONS (FIRE & SMOKE) ABOVE THE CEILING, ON BOTH SIDES OF THE WALL.

M. PROVIDE A MINIMUM OF ONE STUD SEPARATION BETWEEN OUTLET BOXES AND OTHER PENETRATIONS OCCURRING AT

OPPOSITE FACE OF WALLS.

N. PROVIDE CONTINUOUS NON-HARDENING ACOUSTICAL SEALANT AT TOP, SIDES AND EDGES OF BOTH SIDES OF WALL AT ALL NON-RATED GYPSUM BOARD PARTITIONS SCHEDULED TO RECEIVE SOUND ATTENUATION BLANKETS.

O. ALL PENETRATIONS AT NON-RATED WALLS SHALL BE SLEEVED AND PACKED AIRTIGHT WITH SAFING INSULATION AND SEALANT. ALL JOINT OF GYPSUM BOARD PANELS SHALL BE STAGGERED, TAPED, AND SEALED. FRAMING TO 1/2" +/-

CLEARANCE AT PERIMETER OF MECHANICAL DUCTWORK.

P. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

Q. COLD-FORMED STEEL (CFS) FRAMING SUPPLIER SHALL PROVIDE ENGINEERED DRAWINGS.

R. PROVIDE DOUBLE CFS FRAMING STUDS AT JAMBS OF DOOR AND FIXED GLASS FRAMES, AT OPEN PARTITION ENDS, AND WHERE PARTITION IS TO RECEIVE WALL MOUNTED SHELVES, CASEWORK, PLUMBING FIXTURES, ETC.

S. PROVIDE ADDITIONAL BRACING AS REQUIRED AT ALL CFS FRAMING STUD INSTALLATIONS EXCEEDING STUD MANUFACTURER

REQUIREMENTS FOR MAXIMUM ALLOWED HEIGHT AND DEFLECTION.

T. REFER TO MECHANICAL DRAWINGS FOR QUANTITY AND TYPE OF DIFFUSERS, RETURN AIR GRILLES, AND EXHAUST GRILLES.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

U. REFER TO ELECTRICAL DRAWINGS FOR QUANTITY AND TYPES OF LIGHTS, SPEAKERS, DETECTORS, POWER OUTLETS, ETC.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

V. BUILD PARTITIONS IN ACCORDANCE WITH PARTITION TYPE AND DESIGN REFERENCED. REFERENCES ARE TO LATEST EDITION OF GYPSUM ASSOCIATION (GA) FIRE RESISTANCE DESIGN MANUAL, OR TO UNDERWRITERS LABORATORY (UL) FIRE

RESISTANCE DIRECTORY.

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:2

P

M

001-AE102.1

SECOND FLOOR PLAN - ZONE 1

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N

1/8" = 1'-0"

B01 - SECOND FLOOR PLAN - ZONE 1

1/4" = 1'-0"

B01 - SECOND FLOOR REFLECTED CEILING PLAN - NEW WORK

1/4" = 1'-0"

B01 - SECOND FLOOR PLAN - DEMO

1/4" = 1'-0"

B01 - SECOND FLOOR PLAN - NEW WORK

1/4" = 1'-0"

B01 - SECOND FLOOR REFLECTED CEILING PLAN - DEMO

D R A W I N G N O T E S :

1 REMOVE EXISTING CARPET AND MASTIC MATERIAL FROM FLOOR. CLEAN AND PREPARE FLOOR FOR INSTALLATION OF

ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT.

2 WINDOW SECURITY BARS - REFER TO DETAILS ON SHEET AE601 FOR BASIS OF DESIGN AND DETAILS.

3 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

4 ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT - SEE HATCHED AREA.

5 REMOVE EXISTING DOOR FRAME, DOOR, AND HARDWARE; TURN DOOR AND HARDWARE OVER TO VA TO ADD TO

EXISTING STOCK.

6 LEAVE CEILING SUPPORTS IN ADJACENT SPACE TO FUTURE TR. NEW CEILING COMPONENTS TO BE INSTALLED AND TIED

INTO EXISTING CEILING GRID.

7 NO CEILING IN THIS AREA

8 NEW CEILING COMPONENTS TO TIE EXISTING CEILING SYSTEM TO NEW WALL - MATCH EXISTING GRID COMPONENTS

AND ACOUSTICAL CEILING TILES

9 NEW WALL - REFER TO AE601 FOR PARTITION TYPE DETAIL.

10 VINYL WALL BASE ALONG WALL - MATCH EXISTING BASE IN ROOM.

11 WALL MOUNTED FIRE EXTINGUISHER CABINET. PROVIDE NEW 10LB. CLASS C FIRE EXTINGUISHER FOR CABINET. SEE

FIRE CABINET ELEVATION ON SHEET GI001 FOR INSTALLATION HEIGHT.

12 CARD READER - REFER TO ELECTRICAL DRAWINGS

13 PAINT WALLS - REFER TO FINISH SCHEDULE

ZONE 1

ZONE 2

ZONE 4 ZONE 5

ZONE 3

003-AE101.1

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:4

P

M

003-AE101

OVERALL FIRST FLOOR PLAN

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N

1" = 10'-0"

B03 - FIRST FLOOR PLAN - OVERALL

003-AE101.1

Supply

106C

HAC

106E

Toilet

106F

Toilet

106G

Corridor

C1-3

Corridor

C1-1

Vet Rep

107A

Day Treatment Office

Program Assistant

Forms Storage

110A

Elect. Room

111A

Toilet

Office

Incentive Therapy

Vestibule

Office

100G

Office

100E

Office

100F

Stair

S2-1

Stair

S1-1

Elect. Room

100A

Office

100H

Office

100D

Supply

100B

Office

100C

Corridor

Existing Dark Room

106A

Waiting

Corridor

106B

Veteran's Industries Marketing

Corridor

C1-2

2 - 5

TELE. CLOSET

TELE CLOSET

TR

TELE. CLOSET

TR

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S

G E N E R A L C O N S T R U C T I O N N O T E S

A. REFER TO NEW WORK ARCHITECTURAL FLOOR PLANS FOR PARTITION TYPE DESIGNATIONS. SEE PARTITION TYPES ON

SHEET AE601.

B. ALL GYPSUM BOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. PARTITION TYPES INDICATED ARE CONTINUOUS TO A CORNER OR AN INTERSECTING PARTITION, UNLESS INDICATED OTHERWISE. WHERE PARTITIONS OF DIFFERENT THICKNESSES MEET, MAINTAIN A FLUSH SURFACE ON THE SIDE WHERE

FACES ARE STRAIGHT AND CONTINUOUS, UNLESS NOTED OTHERWISE.

D. ALL COLD-FORMED STEEL FRAMING SHALL BE 20 GUAGE OR HEAVIER.

E. EDGES OF GYPSUM BOARD LEFT EXPOSED TO VIEW, OR ABUTTING DISSIMILAR MATERIAL, IS TO BE FINISHED WITH METAL "L"

BEAD TRIM AND COMPOUND UNLESS NOTED OTHERWISE.

F. ALL FIRE RATED WALL AND FLOOR PENETRATION MUST COMPLY WITH ASTM-E814

G. ALL DOOR OPENINGS SHALL BE 4" FROM A PERPENDICULAR PARTITION TO OUTSIDE FACE OF FRAME, UNLESS NOTED OR

DETAILED OTHERWISE.

H. ALL PARTITIONS, INCL. STUDS, BOARD, ETC. SHALL EXTEND FROM TOP OF FLOOR SLAB TO UNDERSIDE OF CONCRETE SLAB

ABOVE UNLESS OTHERWISE NOTED.

I. CONTRACTOR SHALL CLOSE OFF ANY VOIDS LEFT AS A RESULT OF ANY REMOVALS AND NEW CONSTRUCTION, AS WELL AS INFILL ANY EXISTING VOIDS IN NEWLY DESIGNATED FIRE RATED PARTITIONS. ALL PATCHES SHALL MATCH AND ALIGN WITH

SURROUNDING MATERIALS AND SHALL BE IN ACCORDANCE WITH NFPA CODE.

J. CONTRACTOR SHALL SEAL AROUND ALL M.E.P. PENETRATIONS OR OPENINGS, RESULTING FROM M.E.P. INSTALLATIONS INCLUDING BUT NOT LIMITED TO THE SLAB AND PARTITION WALLS ABOVE AND BELOW CEILINGS.

K. NO EXISTING FIREPROOFING IS TO BE REMOVED FROM EXISTING BUILDING STRUCTURE FOR ANY NEW INSTALLATION FOR

ANY REASON.

L. LABEL ALL RATED PARTITIONS (FIRE & SMOKE) ABOVE THE CEILING, ON BOTH SIDES OF THE WALL.

M. PROVIDE A MINIMUM OF ONE STUD SEPARATION BETWEEN OUTLET BOXES AND OTHER PENETRATIONS OCCURRING AT

OPPOSITE FACE OF WALLS.

N. PROVIDE CONTINUOUS NON-HARDENING ACOUSTICAL SEALANT AT TOP, SIDES AND EDGES OF BOTH SIDES OF WALL AT ALL NON-RATED GYPSUM BOARD PARTITIONS SCHEDULED TO RECEIVE SOUND ATTENUATION BLANKETS.

O. ALL PENETRATIONS AT NON-RATED WALLS SHALL BE SLEEVED AND PACKED AIRTIGHT WITH SAFING INSULATION AND SEALANT. ALL JOINT OF GYPSUM BOARD PANELS SHALL BE STAGGERED, TAPED, AND SEALED. FRAMING TO 1/2" +/-

CLEARANCE AT PERIMETER OF MECHANICAL DUCTWORK.

P. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

Q. COLD-FORMED STEEL (CFS) FRAMING SUPPLIER SHALL PROVIDE ENGINEERED DRAWINGS.

R. PROVIDE DOUBLE CFS FRAMING STUDS AT JAMBS OF DOOR AND FIXED GLASS FRAMES, AT OPEN PARTITION ENDS, AND WHERE PARTITION IS TO RECEIVE WALL MOUNTED SHELVES, CASEWORK, PLUMBING FIXTURES, ETC.

S. PROVIDE ADDITIONAL BRACING AS REQUIRED AT ALL CFS FRAMING STUD INSTALLATIONS EXCEEDING STUD MANUFACTURER

REQUIREMENTS FOR MAXIMUM ALLOWED HEIGHT AND DEFLECTION.

T. REFER TO MECHANICAL DRAWINGS FOR QUANTITY AND TYPE OF DIFFUSERS, RETURN AIR GRILLES, AND EXHAUST GRILLES.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

U. REFER TO ELECTRICAL DRAWINGS FOR QUANTITY AND TYPES OF LIGHTS, SPEAKERS, DETECTORS, POWER OUTLETS, ETC.

SCRIBE CEILING MATERIALS CAREFULLY FOR A TIGHT FIT.

V. BUILD PARTITIONS IN ACCORDANCE WITH PARTITION TYPE AND DESIGN REFERENCED. REFERENCES ARE TO LATEST EDITION OF GYPSUM ASSOCIATION (GA) FIRE RESISTANCE DESIGN MANUAL, OR TO UNDERWRITERS LABORATORY (UL) FIRE

RESISTANCE DIRECTORY.

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

VA FORM 08 - 6231

A

FULLY SPRINKLERED

U.S. Department of Veterans Affairs

B

C

D

E

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

A u to d e s k D o c s /C h ill ic o th e V

A

E H

R M

/F F

E

C h ill ic o th e

E H

R M

C a m p u s rv t

/1

/2

:0

:5

P

M

003-AE101.1

FIRST FLOOR PLAN - ZONE 1

07/07/2023 PQ JF

EHRM INFRASTRUCTURE

UPGRADES

538-21-701

CHILLICOTHE, OHIO

BID DOCUMENTS - 100%

CHILLICOTHE

VAMC

Approved: Veteran's Affairs Medical Center

N

1/8" = 1'-0"

B03 - FIRST FLOOR PLAN - ZONE 1

1/4" = 1'-0"

B03 - FIRST FLOOR PLAN - DEMO

1/4" = 1'-0"

B03 - FIRST FLOOR PLAN - NEW WORK

1/4" = 1'-0"

B03 - FIRST FLOOR REFLECTED CEILING PLAN - DEMO

1/4" = 1'-0"

B03 - FIRST FLOOR REFLECTED CEILING PLAN - NEW WORK

D R A W I N G N O T E S :

1 REMOVE EXISTING CARPET AND MASTIC MATERIAL FROM FLOOR. CLEAN AND PREPARE FLOOR FOR INSTALLATION OF

ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT.

2 REMOVE CEILING SYSTEMS AND SUPPORTS

3 ELECTROSTATIC DISSIPATING (ESD) EPOXY FLOOR PAINT - SEE HATCHED AREA.

4 3/4" FIRE-RETARDANT TREATED PLYWOOD - 4' X 8' SHEETS ALIGN WITH EXISTING - CUT AROUND OUTLETS AND CONDUIT.

PAINT WHITE ALL BUT FIRE RATING LABEL.

5 WINDOW SECURITY BARS - REFER TO DETAILS ON SHEET AE601 FOR BASIS OF DESIGN AND DETAILS.

6 NO CEILING IN THIS AREA

7 WALL MOUNTED FIRE EXTINGUISHER CABINET. PROVIDE NEW 10LB. CLASS C FIRE EXTINGUISHER FOR CABINET. SEE

FIRE CABINET ELEVATION ON SHEET GI001 FOR INSTALLATION HEIGHT.

8 EXISTING CARD READER TO REMAIN

Uniform/PAP Work Room

108K2

PAP Storage

108K3

Toilet

108K4

PAP Storage

108K1

Uniform Drop-off

108K

Toilet

108J

Vestibule

108V2

Corridor

108L

Serving Line/Dining Area

Chief Dietetics

106A

Vestibule

108V1

Dietetics Secretary

106B

Conference Room

Mechanical

106H

Entry

106I

Delivery/Entry

105B

Cart Room

Office

106E

Office

106F

Office

106G Office

106D

HAC

105A

Elect. Room

107A

Toilet

106C

Tele Clos

106K

Closet

106J

Kitchen

104A

Kitchen

Supervisor's Office

Stair 2

S-2-1

Office

Toilet

Freezer

Corridor

Entry Corridor

HAC

115A

Mechanical

109A

Freezer

Dishwashing

109Toilet

Toilet

Vestibule

108V4

Tray Line Assembly

108C

Corridor

109D

HAC

109B Dishwashing

Dietician Office

108F

Toilet

108A

Toilet

108B

TR

108D

Soiled Utility

108G Clean Linen

108H

HAC

108E

Ingredient Control

Refrigerator

118BFreezer

118C

Entry

Stair 1

S-1-1

Toilet

120B

Closet

120C

Office

120A

Freezer

118E

Refrigerator

118D

Vestibule

108V3

Office

120D

Mechanical/Generator Room

109CDock

104B

Closet

105C

Corridor

007-AE101

22 - 5

TELE. CLOSET

108D

REMOVE FLOORING BOUNDARY

108D

TR

108D

108E

HAC

108E

1 1

TELE. CLOSET

108D

TR

108D

A. CONTRACTOR TO DISPOSE OF CONSTRUCTION DEMOLITION DEBRIS.

B. REMOVE ALL CONSTRUCTION DEMOLITION DEBRIS ON DAILY BASIS.

G E N E R A L D E M O L I T I O N N O T E S G E N E R A L C O N S T R U C T I O N N O T E S

A. ALL PROPOSED PARTITIONS ARE ARE TYPE 1 - REFER TO WALL TYPE DETAIL ON SHEET GI001.

B. ALL WALLBOARD IS TO BE TYPE "X" UNLESS NOTED OTHERWISE.

C. ALL DIMENSIONS ARE TO COLUMN CENTERLINES OR FINISHED ELEVATION OF WALLS OR SURFACES UNLESS NOTED

OTHERWISE.

D. CONTRACTOR TO PROVIDE ALL RELATED FASTENERS, TRIM AND ACCESSORIES FOR INSTALL PRODUCTS PER

MANUFACTURER'S WRITTEN INSTRUCTIONS.

E. REFER TO DEMOLITION DRAWINGS, IF ANY, FOR WORK REQUIRED IN ADVANCE OF CONSTRUCTION AND COORDINATE

ACCORDINGLY.

F. ALL DOOR FRAMES ARE TO BE INSTALLED 4" AWAY OF ADJACENT PERPENDICULAR WALLS UNLESS NOTED…