Hipcan_Width_MITR.pdf
PDF 38 KB Posted
- Attached to
- HIP CAN Study
- Solicitation number
- 0000963801
- Issued by
-
Department of Energy
About this file
This is a technical drawing and manufacturing specification for a MITR Plate component identified as part number C61T01V0. The document provides detailed dimensional specifications, tolerances, material requirements, and finishing instructions for the fabrication and assembly of this part, which appears to be a hollow cylindrical plate measuring approximately 40.125 inches in length with an inner width of 6.10±.02 inches and constructed from 18-gauge material.
The manufacturing requirements include applying Neolube 1.1 coating to all surfaces per manufacturer specifications followed by baking, individually vacuum sealing parts in 5-mil Mylar bags, and applying thermal transfer labels with SAP and serial numbers to each sealed bag. Parts must be marked via electrochemical etching or laser engraving with identification information in a specified format (10-digit SAP number, 5-digit lot number, 8-digit serial number) at 0.13 inches high and no more than 0.002 inches deep. Standard tolerances apply with angular tolerances of ±0.5 degrees and surface finish specifications of 63 RMS microinches. All sharp edges must be broken, and a maximum draft angle of 2% is permitted. The drawing was created by Fiona Gailey, reviewed by Dustin Clelland, and approved by Taylor Mason, with a revision date of August 6, 2026.
View the file
Other files
Show all 15
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
THIRD ANGLE PROJECTION
40.125±.020 2x 1.125
6.10±.02
R1.50
A
A
APPLY NEOLUBE TO
INNER SURFACE ONLY
NON-PART NUMBER SIDE.
0.06
R.125
18 GAUGE
.99
6.10±.02
R.20
C
SECTION A-A
SCALE 1 : 1
DETAIL C
SCALE 2 : 1
MAX DRAFT ANGLE: 2%
1. SPRAY NEOLUBE 1.1 ON ALL SURFACES UNLESS OTHERWISE NOTED PER MANUFACTURER’S DIRECTIONS, BAKE ALL PARTS
PER MANUFACTURER’S INSTRUCTIONS.
2. INDIVIDUALLY VACUUM SEAL PARTS INDIVIDUALLY IN 5MIL MYLAR BAGS OR BUYER APPROVED EQUAL.
3. ADD SAP NUMBER AND SERIAL NUMBER TO EACH SEALED BAG WITH A 1 X 3 HARSH ENVIRONMENT THERMAL TRANSFER
LABEL OR BUYER APPROVED EQUAL.
4. ELECTROCHEMICALLY ETCH OR LASER ENGRAVE PARTS WITH SAP NUMBER, LOT, AND SERIAL NUMBER 0.13” HIGH AND NO MORE THAN 0.002" DEEP. FORMAT IS: 10 DIGIT SAP NUMBER - 5 DIGIT LOT NUMBER-8 DIGIT SERIAL NUMBER
(XXXXXXXXXX-XXXXX-XXXXXXXX) OR BUYER APPROVED EQUAL
INNER LENGTH
INNER WIDTH
A A
B B
ANGULAR ± 0.5
SURFACE FINISH
RMS
µ in
LENGTH
.0 = ±.1
.00 = ±.01 .000 = ±.005
.0000 = ±.005
PROJECT:
MATERIAL:
UNLESS OTHERWISE SPECIFED:
ALL DIMENSIONS ARE INCHES
STANDARD TOLERANCES: INCHES
NOTE: BREAK ALL SHARP EDGES
SHEET 1 OF 2SCALE: 1:4
XX.XX lb
DRAWN BY: Fiona Gailey
TITLE:
APRROVED BY: Taylor Mason
REVIEWED BY: Dustin Clelland
DATE
REV.
SIZE
B
08/06/2026
SAP NUMBER:PART NUMBER:
XXXXXC61T01V0
WEIGHT:
MITR PLATE
HIP CAN
08/06/2026
07/20/2026
| Sheet1 |
| Bottom View |
| Drawing View10 |
| Section View A-A |
| Detail View C (2 : 1) |
File details come from the government source that posted it. Updated .