0.011 Pocket Depth-Cladding_MITR (1).pdf
PDF 63 KB Posted
- Attached to
- HIP CAN Study
- Solicitation number
- 0000963801
- Issued by
-
Department of Energy
About this file
This is a technical engineering drawing for a machined aluminum part designated as "MITR PLATE" with SAP number C66T02V0. The part is fabricated from 6061 alloy aluminum and weighs 0.89 pounds. The plate measures 40.095±0.005 inches in length with a 0.011-inch pocket depth cladding and features four rounded corners with 1.49-inch radii, precise dimensional specifications, and a surface finish requirement of 63 RMS microinches. The material is 18-gauge thickness with angular tolerances of ±0.5 degrees and standard inch-based tolerances (±0.1 for single-decimal, ±0.01 for double-decimal, and ±0.005 for triple and quadruple-decimal dimensions).
The drawing specifies five manufacturing and finishing requirements: parts must be individually vacuum-sealed in 5-mil Mylar bags with buyer-approved alternatives permitted; each sealed bag must be labeled with SAP number and serial number using a 1x3 harsh environment thermal transfer label; parts must be electrochemically etched or laser engraved with SAP number, lot number, and serial number in 0.13-inch-high characters no deeper than 0.002 inches (format: 10-digit SAP-5-digit LOT-8-digit serial number); parts must be rinsed with deionized water to remove chips and contaminants, followed by a wipe with denatured alcohol; and all sharp edges must be broken. The drawing was prepared by Fiona Gailey on 07/02/2026, reviewed by Dustin Clelland, and approved by Taylor Mason on 08/06/2026, with Revision 0 dated 08/06/2026.
View the file
Other files
Show all 21
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
THIRD ANGLE PROJECTION
40.095±.005
2.25±.005 6.07±.005
22.387±.005 4x R1.49
18 GAUGE
A
.011
R.002
DETAIL A
SCALE 5 : 1
1. INTENTIONALLY LEFT BLANK
2. INDIVIDUALLY VACUUM SEAL PARTS INDIVIDUALLY IN 5MIL MYLAR BAGS OR BUYER APPROVED EQUAL.
3. ADD SAP NUMBER AND SERIAL NUMBER TO EACH SEALED BAG WITH A 1 X 3 HARSH ENVIRONMENT THERMAL
TRANSFER LABEL OR BUYER APPROVED EQUAL.
4. ELECTROCHEMICALLY ETCH OR LASER ENGRAVE PARTS WITH SAP NUMBER, LOT, AND SERIAL NUMBER 0.13” HIGH AND NO MORE THAN 0.002" DEEP. FORMAT IS: 10 DIGIT SAP NUMBER - 5 DIGIT LOT NUMBER-8 DIGIT SERIAL
NUMBER (XXXXXXXXXX-XXXXX-XXXXXXXX) OR BUYER APPROVED EQUAL
5. RINSE WITH DEIONIZED WATER TO REMOVE CHIPS AND OTHER CONTAMINANTS, FOLLOWED BY A WIPE WITH
DENATURED ALCOHOL
C66T02V0
MITR PLATE
0.011" POCKET DEPTH - CLADDING
A A
B B
6061 Alloy
ANGULAR ± 0.5
SURFACE FINISH
RMS
µ in
LENGTH
.0 = ±.1
.00 = ±.01 .000 = ±.005
.0000 = ±.005
PROJECT:
MATERIAL:
UNLESS OTHERWISE SPECIFED:
ALL DIMENSIONS ARE INCHES
STANDARD TOLERANCES: INCHES
NOTE: BREAK ALL SHARP EDGES
SHEET 1 OF 1SCALE: 1:5
0.89 lb
DRAWN BY: Fiona Gailey
TITLE:
APRROVED BY: Taylor Mason
REVIEWED BY: Dustin Clelland
DATE
REV.
SIZE
B
08/06/2026
SAP NUMBER:PART NUMBER:
XXXXX
WEIGHT:
08/06/2026
07/02/2026
| Sheet1 |
| Top |
| Front |
| Detail View A (5 : 1) |
| Drawing View5 |
File details come from the government source that posted it. Updated .