10Gabottom_MITR.pdf
PDF 58 KB Posted
- Attached to
- HIP CAN Study
- Solicitation number
- 0000963801
- Issued by
-
Department of Energy
About this file
This is a technical engineering drawing for a "MITR PLATE" component, designated as part number C63T01V0, which functions as a 10 gauge bottom strong back. The part is manufactured from ASTM A1008 material and weighs 9.13 pounds. The drawing specifies detailed dimensional tolerances, with key measurements including a length of 40.095±.005 inches, a width of 6.07±.005 inches, and a radius of 1.49 inches at one end. Standard tolerances apply: ±0.1 inches for single decimal places, ±0.01 for two decimals, and ±0.005 for three or more decimals. Angular tolerances are ±0.5 degrees, with a surface finish of 63 RMS microinches. The drawing was created on 08/06/2026 and reviewed by Dustin Clelland, with approval from Taylor Mason and drawing responsibility assigned to Fiona Gailey.
The manufacturing specifications include four critical process requirements: all surfaces must be spray coated with Neolube 1.1 per manufacturer's instructions and subsequently baked; parts must be individually vacuum sealed in 5-mil Mylar bags; each sealed bag must be labeled with a harsh environment thermal transfer label containing the SAP number and serial number; and parts must be electrochemically etched or laser engraved with identification markings in a specific format (10-digit SAP number, 5-digit lot number, and 8-digit serial number) at 0.13 inches high and no more than 0.002 inches deep. All sharp edges must be broken per standard practice. The drawing includes a detail view (Detail A, Scale 4:1) showing edge specifications and is presented in third-angle projection on a single-sheet format at a 1:5 scale.
View the file
Other files
Show all 15
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
THIRD ANGLE PROJECTION
6.07±.005
40.095±.005
R1.49
10 GAUGE
A
R.135
DETAIL A
SCALE 4 : 1
1. SPRAY NEOLUBE 1.1 ON ALL SURFACES UNLESS OTHERWISE NOTED PER MANUFACTURER’S DIRECTIONS, BAKE ALL PARTS PER MANUFACTURER’S INSTRUCTIONS.
2. INDIVIDUALLY VACUUM SEAL PARTS INDIVIDUALLY IN 5MIL MYLAR BAGS OR BUYER APPROVED EQUAL.
3. ADD SAP NUMBER AND SERIAL NUMBER TO EACH SEALED BAG WITH A 1 X 3 HARSH ENVIRONMENT THERMAL
TRANSFER LABEL OR BUYER APPROVED EQUAL.
4. ELECTROCHEMICALLY ETCH OR LASER ENGRAVE PARTS WITH SAP NUMBER, LOT, AND SERIAL NUMBER 0.13” HIGH AND NO MORE THAN 0.002" DEEP. FORMAT IS: 10 DIGIT SAP NUMBER - 5 DIGIT LOT NUMBER-8 DIGIT SERIAL
NUMBER (XXXXXXXXXX-XXXXX-XXXXXXXX) OR BUYER APPROVED EQUAL
C63T01V0
MITR PLATE
10 GAUGE BOTTOM - STRONG BACK
A A
B B
ASTM A1008
ANGULAR ± 0.5
SURFACE FINISH
RMS
µ in
LENGTH
.0 = ±.1
.00 = ±.01 .000 = ±.005
.0000 = ±.005
PROJECT:
MATERIAL:
UNLESS OTHERWISE SPECIFED:
ALL DIMENSIONS ARE INCHES
STANDARD TOLERANCES: INCHES
NOTE: BREAK ALL SHARP EDGES
SHEET 1 OF 1SCALE: 1:5
9.13 lb
DRAWN BY: Fiona Gailey
TITLE:
APRROVED BY: Taylor Mason
REVIEWED BY: Dustin Clelland
DATE
REV.
SIZE
B
08/06/2026
SAP NUMBER:PART NUMBER:
XXXXX
WEIGHT:
08/06/2026
06/08/2026
| Sheet1 |
| Drawing View1 |
| Drawing View2 |
| Drawing View3 |
| Detail View A (4 : 1) |
File details come from the government source that posted it. Updated .