0.0145 Pocket Depth-cladding_MITR (1).pdf
PDF 63 KB Posted
- Attached to
- HIP CAN Study
- Solicitation number
- 0000963801
- Issued by
-
Department of Energy
About this file
This document is an engineering drawing (technical specification sheet) for a part designated as the "MITR PLATE" with SAP number C66T01V0. The part is manufactured from 6061 aluminum alloy and weighs 0.87 pounds. The drawing specifies precise dimensional requirements using third-angle projection, including an overall length of 40.095±.005 inches, a pocket depth of 0.0145 inches for cladding, four rounded corners with a 1.49-inch radius, and 18-gauge material thickness. Standard tolerances are applied with angular tolerances of ±0.5 degrees and length tolerances varying by decimal precision (±0.1 inches for one decimal place, ±0.005 inches for four decimal places). Surface finish is specified at 63 RMS microinches.
The drawing includes five numbered notes detailing manufacturing and assembly requirements. Parts must be individually vacuum-sealed in 5-mil mylar bags with harsh environment thermal transfer labels displaying the SAP number and serial number. Identification marking must be applied via electrochemical etching or laser engraving at 0.13 inches high with a maximum depth of 0.002 inches, following the format of a 10-digit SAP number, 5-digit lot number, and 8-digit serial number. All sharp edges must be broken, and final cleaning requires rinsing with deionized water to remove chips and contaminants, followed by wiping with denatured alcohol. The drawing was drawn by Fiona Gailey, reviewed by Dustin Clelland, approved by Taylor Mason, and issued on August 6, 2026, with a previous revision dated July 20, 2026.
View the file
Other files
Show all 21
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
THIRD ANGLE PROJECTION
40.095±.005
2.25±.005 6.07±.005
22.387±.005 4x R1.49
18 GAUGE
A
.0145
R.002
DETAIL A
SCALE 5 : 1
1. INTENTIONALLY LEFT BLANK
2. INDIVIDUALLY VACUUM SEAL PARTS INDIVIDUALLY IN 5MIL MYLAR BAGS OR BUYER APPROVED EQUAL.
3. ADD SAP NUMBER AND SERIAL NUMBER TO EACH SEALED BAG WITH A 1 X 3 HARSH ENVIRONMENT THERMAL
TRANSFER LABEL OR BUYER APPROVED EQUAL.
4. ELECTROCHEMICALLY ETCH OR LASER ENGRAVE PARTS WITH SAP NUMBER, LOT, AND SERIAL NUMBER 0.13” HIGH AND NO MORE THAN 0.002" DEEP. FORMAT IS: 10 DIGIT SAP NUMBER - 5 DIGIT LOT NUMBER-8 DIGIT SERIAL
NUMBER (XXXXXXXXXX-XXXXX-XXXXXXXX) OR BUYER APPROVED EQUAL
5. RINSE WITH DEIONIZED WATER TO REMOVE CHIPS AND OTHER CONTAMINANTS, FOLLOWED BY A WIPE WITH
DENATURED ALCOHOL
0.0145" POCKET DEPTH - CLADDING
A A
B B
6061 Alloy
ANGULAR ± 0.5
SURFACE FINISH
RMS
µ in
LENGTH
.0 = ±.1
.00 = ±.01 .000 = ±.005
.0000 = ±.005
PROJECT:
MATERIAL:
UNLESS OTHERWISE SPECIFED:
ALL DIMENSIONS ARE INCHES
STANDARD TOLERANCES: INCHES
NOTE: BREAK ALL SHARP EDGES
SHEET 1 OF 1SCALE: 1:5
0.87 lb
DRAWN BY: Fiona Gailey
TITLE:
APRROVED BY: Taylor Mason
REVIEWED BY: Dustin Clelland
DATE
REV.
SIZE
B
08/06/2026
SAP NUMBER:PART NUMBER:
XXXXX
WEIGHT:
08/06/2026
07/20/2026
C66T01V0
MITR PLATE
| Sheet1 |
| Top |
| Front |
| Detail View A (5 : 1) |
| Drawing View5 |
File details come from the government source that posted it. Updated .