Attachment 14 LOCRF RTA AF Sust Scoresheet GP vFeb2017.xlsx

Scoresheet

WINSLOW, JAMES A JR CTR USAF HAF AFCEC/CFTS: HPSB III.3 Stormwater Management is required if:

Project is in the United States, US Territory, or Possession of the US;

Project includes construction or expansion of one or more buildings;

AND Footprint (new impervious surfaces) is greater than 5,000 gross square feet.

FALSE HPSB VI.1_NA Address Climate Change Risk_NA

&D &P

&D &P

Solar PV Solar CP Solar Thermal Electric Geothermal

GSHP

Wind Hydro Waste to Energy Renewables were not lifecycle cost effective Date Project Registered (MM/DD/YY) Date Project Certified (MM/DD/YY) Clear Cool roof Green roof Solar electric Solar thermal Solar Passive Retaining stormwater impact receving water flow Site too small to infiltrate significant volume State or local restrict water harvesting Shallow bedrock, contaminated soil, high ground water table, underground utilities Non-potable water demand to small Structural, plumbing, and other mods not feasible Soil infiltration capacity limited State or local restrict use of green infrastructure or LID Other Bio-Retention Infiltration Trench Soil Amendments Dry Wells Inlet Pollution Removal Device Permeable Pavement/Pavers Filter Strips Grassed Swells Rain Barrels/Cisterns Tree Box Filters Vegetated Buffers Vegetated Roof Other

NA_Justification

Guidance

HPSB I.1

UFC 1-200-02 para 2-2.1 Incorporate the following planning and evaluation into the integrated design, as described in ASHRAE 189.1 Informative Appendix F (Integrated Design). Follow the steps of design optimization, as applicable, in ASHRAE 189.1 Section F1.1.1 (Charrette Process).

Use a collaborative, integrated planning and design team, composed of user, government support staff, and appropriate professionals, to identify requirements and to establish performance goals for siting, energy, water, materials, indoor environmental quality, and other comprehensive design goals. Ensure incorporation of these goals throughout the design and lifecycle of the building, including deconstruction.

Evaluate the site and building components to determine whether passive and natural design strategies and features are cost effectively incorporated before the active and mechanical systems are designed. Incorporate these features where applicable.

Take into account site attributes, including climate and local and regional context, which impact the design of the building.

During the site selection process, meet the requirements of UFC 2-100-01. See Appendix B “Best Practices” for desirable site characteristics.

During the planning and design process meet the requirements of applicable UFCs, and use the following site development considerations and passive strategies:

• Site design elements that ensure safe and convenient pedestrian access.

• Meet the requirements of UFC 3-201-02.

• Incorporate results of site analysis, in order to design the building, focusing on orientation, configuration and massing.

• Orient building to maximize energy efficiency, passive solar and daylighting potential.

• Select, design and integrate into the overall building, high performance and sustainable systems (e.g., HVAC, plumbing, water heating systems, lighting systems, control systems, elevators, building envelope and fire protection systems).

• Promote opportunities for occupants to voluntarily increase physical movement such as making stairwells a desirable option for circulation and active workstations.

Commissioning

HPSB I.2

UFC 1-200-02 para 2-2.2 In order to verify design and performance, and ensure that the Government requirements are met, employ commissioning practices appropriate to the size and complexity of the building and its system components. This must include an experienced commissioning provider, who should be independent of the project design and construction team, and the operations team. The choice of either contracted services or Government personnel to serve as the commissioning provider will be determined at project level.

Meet the requirements of ASHRAE 189.1 Section 10.3.1.2 (Building Project Commissioning), with the following modifications:

• For buildings and systems that are less complex6, commissioning may be tailored as determined by the DOD Component AHJ.

• “Schematic design” is the design charrette or similar conceptual design activity.

• Documentation as described in ASHRAE 55 Section 6.2 is not required.

For Air Force projects, the Project Delivery Team must determine the level of commissioning activities required.

HPSB II.1

UFC 1-200-02 para 2-3.1 Energy Efficiency - Base energy efficiency design decisions on life-cycle cost as indicated in Chapter 1 of UFC 1-200-02.

Commercial and Multi-Family High-Rise Residential Buildings:

• Meet the requirements of ASHRAE 90.1. Use ASHRAE 90.1(2010) for all projects with design starts before November 6, 2016. Use ASHRAE 90.1(2013) thereafter.

• Design the building to achieve at least 30% energy consumption reduction from ASHRAE 90.1 baseline.

• If a 30% reduction is not LCCE, modify the design of the proposed building to achieve an energy consumption level at the highest level of energy efficiency that is LCCE.

• Determine energy consumption levels for both the ASHRAE Baseline Building and proposed building by using the Performance Rating Method found in appendix G of ASHRAE 90.1, except the formula for calculating the Performance Rating.

Replace the formula in G1.2 with the following:

Percentage improvement = 100 × ((Baseline building consumption − Receptacle and process loads) − (Proposed building consumption − Receptacle and process loads)) / (Baseline building consumption − Receptacle and process loads)

Low-Rise Residential Buildings:

• Meet the requirements of International Energy Conservation Code (IECC).

• Design the building to achieve at least 30% energy consumption reduction from the IECC baseline using the Simulated Performance Alternative found in Section 405 of the IECC.

• If a 30% reduction is not LCCE, modify the design of the proposed building to achieve an energy consumption level at the highest level of energy efficiency that is LCCE.

Renovations:

• Renovation projects that replace everything above the foundation must either apply 2-3.1.1 or 2-3.1.2 as applicable.

• All other renovations choose one of the following options:

1. Reduce measured building energy use by at least 30%, below FY 2003 energy use baseline.

2. Reduce measured building energy use by at least 20% below FY 2015 energy use baseline.

3. Reduce modeled energy use (from all sources including renewable energy) by 20% compared to the ASRHAE 90.1 baseline building design.

• If none of the reduction choices is life-cycle cost-effective, modify the design of the proposed building system(s) to achieve an energy consumption level at the highest level of energy efficiency that is life-cycle cost-effective.

Energy Efficient Products

HPSB II.1

UFC 1-200-02 para 2-3.1.4 Energy Efficient Products – Per EISA 2007 Section 525, acquire products that are ENERGY STAR®-qualified or meet FEMP-designated efficiency requirements in all covered product categories. Select products based on life cycle cost, not initial cost. Link to EPA sites: http://www.energystar.gov/ or http://www1.eere.energy.gov/femp/

Per EISA 2007 Section 524, provide commercially available, off-the-shelf products that use no more than 1 watt in their standby mode.

HPSB II.2

UFC 3-440-01 para 2-3.2 Provide on-site renewable energy systems in accordance with ASHRAE 189.1 Section 7.4.1.1 (On-Site Renewable Energy Systems) and UFC 3-440-01 where LCCE, considering climate, infrastructure condition, mission compatibility, and effects on base wide electrical system (grid) power quality. Exception: Do not use purchase of renewable energy certificates (RECs) as a substitute for the Section 7.4.1.1 new building requirement.

Air Force will utilize an installation-level solution to renewable energy systems and will not require ASHRAE 189.1 Section 7.3.2 if a building-level solution is not LCCE.

HPSB II.3

HPSB II.4

HPSB II.1

HPSB III.1

UFC 1-200-02 para 2-4.1 Indoor Water – Base water efficiency design decisions on life-cycle cost as indicated in Chapter 1 of UFC 1-200-02.

• Meet the requirements of ASHRAE 189.1 Section 6.3.2 (Building Water Use Reduction), which incorporates USEPA WaterSense-labeled products. Water closet replacements in renovations may have a flush value of up to 1.6 GPF (6.1 LPF) to accommodate existing plumbing capacity.

• Meet the requirements of ASHRAE 189.1 Section 6.4.2 (Building Water Use Reduction).

• Meet the requirements of ASHRAE 189.1 Section 6.4.3 (Special Water Features).

Indoor Water Metering

HPSB III.1

UFC 1-200-02 para 2-4.1.1 Indoor Water Metering -- Install advanced water meters to monitor building indoor potable water consumption, as required by DOD Utilities Meter Policy, 16 April 2013.

HPSB III.2

UFC 1-200-02 para 2-4.2 Outdoor Water --

• Limit potable irrigation water use by 50% compared to the conventional methods, and when LCCE, by using the methodologies in ASHRAE 189.1: Section 6.3.1 (Mandatory Provisions: Site Water Use Reduction) and either Section 6.4.1 (Prescriptive Option: Site Water Use Reduction) or Section 6.5.1 (Performance Option: Site Water Use Reduction).

• For existing systems, if a building has a single water meter, reduce indoor and outdoor potable water use combined by at least 20% compared to building water use in 2007. Compare results to a baseline building, using the EPA WaterSense landscape water budget tool version 1.01 or later, or a Component approved tool.

• Show preference for irrigation contractors who are certified through a WaterSense labeled program, or other industry-recognized credentialing programs.

• Refer to UFC 3-201-02 for additional requirements.

Outdoor Water MeteringWater

HPSB III.2

UFC 1-200-02 para 2-4.2.1 Water metering for landscaping – When potable water is used, provide water meters for irrigation systems serving more than 25,000 square feet of landscape, when life-cycle cost-effective. Install advanced water meters to monitor outdoor potable water consumption, as required by DOD Utilities Meter Policy, 16 April 2013.

For all other irrigation systems, separate water meters for locations with outdoor water use are encouraged.

HPSB III.3

HPSB III.4

UFC 3-210-10 para 2-4.3.1 The criteria and design standards in UFC 3-210-10 are required for the planning, design and construction of all Department of Defense (DoD) projects in the United States, United States Territories and Possessions of the United States that meet both of the following conditions:

1) The project includes construction or expansion of one or more buildings as part of its primary scope (i.e., primary facilities vice supporting facilities).

2) The “footprint” is greater than 5,000 gross square feet (464.5 square meters). “Footprint” consists of all new impervious surfaces associated with the building(s), including both building area and pavement area of associated supporting facilities (such as parking and sidewalks). “Footprint” does not include existing building area to be renovated, existing pavement area to be resurfaced, or new pavement area other than supporting facilities associated with the building(s).

For projects in the United States, United States Territories, and Possessions of the United States that do not meet the applicability requirements above, LID techniques apply to the extent practical.

HPSB IV.1

UFC 1-200-02 para 2-5.1 Meet the requirements of ASHRAE 55. Compliance with standards by providing passive (non-mechanical) thermal comfort methods are allowed and encouraged as described in paragraph entitled, “Integrated Design” in UFC 1-200-02.

Exception: For Medical Treatment Facilities, refer to UFC 4-510-01 Medical Military Facilities for thermal comfort criteria.

HPSB IV.2

UFC 1-200-02 para 2-5.1 Meet the requirements of ASHRAE 62.1 (62.2 for low-rise residential).

Exception: For Medical Treatment Facilities, refer to UFC 4-510-01 Medical Military Facilities for ventilation criteria.

HPSB IV.3

UFC 1-200-02 para 2-5.2 All regularly occupied spaces located on the exterior wall must have vision fenestration. Where mission precludes vision fenestration for regularly occupied spaces located on the exterior wall, daylighting is still required. All classrooms and offices must have daylighting. Meet the requirements of ASHRAE 189.1 Section 8.4.1.2 (Minimum Sidelighting effective Aperture for Office Spaces and Classrooms) or Section 8.5.1.2 (Usable Daylight Illuminance in Office Spaces and Classrooms). Provide automated lighting controls in accordance with UFC 3-530-01.

Exception: For Medical Treatment Facilities, refer to UFC 4-510-01 Medical Military Facilities for additional daylighting criteria.

HPSB IV.4

HPSB IV.5

UFC 1-200-02 para 2-5.3.2 Specify materials and products with low or no pollutant emissions, including composite wood products, adhesives, sealants, interior paints and finishes, carpet systems, and furnishings. Meet the requirements of ASHRAE 189.1 Section 8.4.2 (Prescriptive Option: Materials).

Exception: Exclude compliance with 8.4.2, first sentence.

HPSB IV.6

UFC 1-200-02 para 2-5.3.3 For new construction and for renovation of unoccupied existing buildings, comply with ASHRAE 189.1 Section 10.3.1.4 (Indoor Air Quality (IAQ) Construction Management), with maximum outdoor air consistent with achieving relative humidity no greater than 60%.

For renovation of occupied existing buildings, comply with ANSI/SMACNA 008-2008, 2nd Edition, SMACNA IAQ Guidelines for Occupied Buildings Under Construction.

HPSB IV.7

HPSB IV.8

HPSB V.1

HPSB V.2

HPSB V.3

UFC 1-200-02 para 2-6.1.4 Meet the requirements of ASHRAE 189.1 Section 9.3.3 (Refrigerants), if equipment or systems using ozone depleting substances are included in the project. Do not use ozone depleting substances (ODS) or high Global Warming Potential (GWP) chemicals where EPAs Significant New Alternative Policy (SNAP) has identified acceptable substitutes or where other environmentally preferable products are available for use in construction, repair or end-of-life replacements: www.epa.gov/snap

Exceptions: Refer to UFC 3-600-01 for fire protection system requirements.

HPSB V.4

HPSB V.5

HPSB VI.1

UFC 1-200-02 para 2-7 Provide building design solutions responsive to any Government-provided projections of climate change projection and determination of acceptable risk.

For a building located in a floodplain of concern, provide design solutions which mitigate both impact on the floodplain, and impact of the design flood event on building function and occupants, consistent with mission criticality.

&P

&P https://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/http://frwebgate.access.gpo.gov/cgi-bin/getdoc.cgi?dbname=110_cong_bills&docid=f:h6enr.txt.pdfhttp://www.wbdg.org/ccb/browse_cat.php?c=3https://www.fedcenter.gov/programs/eo13693/http://www.wbdg.org/ccb/browse_cat.php?c=3http://www.gpo.gov/fdsys/granule/CFR-2011-title10-vol3/CFR-2011-title10-vol3-sec433-5/content-detail.htmlhttps://www.fedcenter.gov/programs/eo13693/http://frwebgate.access.gpo.gov/cgi-bin/getdoc.cgi?dbname=110_cong_bills&docid=f:h6enr.txt.pdfhttps://www.fedcenter.gov/programs/eo13693/http://frwebgate.access.gpo.gov/cgi-bin/getdoc.cgi?dbname=109_cong_bills&docid=f:h6enr.txt.pdfhttps://www.fedcenter.gov/programs/eo13693/https://www1.eere.energy.gov/femphttps://www.energystar.gov/http://thomas.loc.gov/cgi-bin/query/z?c102:H.R.776.ENR:https://www.federalregister.gov/articles/2008/12/22/E8-30377/protecting-federal-employees-and-the-public-from-exposure-to-tobacco-smoke-in-the-federal-workplacehttps://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/https://www.fedcenter.gov/programs/eo13693/ EISA Section 438

Color Legend

LocationList

Dropdowns

image1.emf image2.emf image3.png image4.png