Navy Coat Womens pgc02229_nctrf29628v5.pdf

PGC0229 COAT, WOMEN'S, SERVICE DRESS BLUE

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY

REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN

WHICH CASE THE AMENDMENT DATE CONTROLS.

SHALL BE MADE IN ACCORDANCE WITH NCTRF PD-29628 DATED 2 APRIL 2014 AND NCTRF 041-14 DATED 17

JUNE 2014

PATTERN DATE: 20 December 2013

STANDARD SAMPLE FOR POLYESTER/WOOL GABARDINE,

BLUE SHADE 3346, CONFORMING TO TYPE II,

CLASS 12 OF MIL-DTL-10176 DATED 11 MARCH 1998

IS AVAILABLE UNDER PIECE NUMBER 17267

INTERIM CHANGES TO NCTRF PD-29628:

PAGE 9, PARAGRAPH 3.3.12.4, Delete the current requirements for the "DSCP Exclusive label" in its entirety and substitute the following:

"3.3.12.4, Exclusive Label. Each coat shall contain the Exclusive label. The jacquard woven Exclusive label shall incorporate the DLA Logo (attached) and shall specify "Made exclusively for Defense Logistics Agency" and shall include "by" and the contractor's name. The label shall be positioned sewn above the inside right pocket and centered above the pocket opening. Label shall be approximately 2 inches square and sewn on all four sides. The proposed finished label's design shall be submitted to the contracting officer for approval.

ADDITIONAL INFORMATION FOR MIL-C-29628:

PAGE 9, PARA. 3.2.14.1, AT THE END OF THE FIRST

SENTENCE ADD "OR AS AN ALTERNATIVE, THE USE OF

4800WT POLYESTER LABELING TAPE IS APPROVED".

PAGE 31, TABLE I, OPERATION 32. PRESS COAT.

DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING:

32. PRESS COAT.

A. FINISHED APPEARANCE. THE FINISHED PRESSED

COAT SHALL BE FREE OF GLOSS, WRINKLES, CREASES,

SPOTS, AND IMPRESSIONS FROM MARKING TICKETS,

THREAD, SEAM AND BINDNG. THE BUST SEAM SHALL

NOT BREAK OR "CAVE-IN" BELOW THE SHOULDERS.

THE SLEEVES SHALL BE BALANCED AND HANG EVENLY.

THE SLEEVE AND SLEEVE HEMS SHALL NOT BE

CREASED. THE COLLAR SHALL ROLL ON THE FINISHED

COAT AND HUG THE NECKLINE AND THE COLLAR EDGES

SHALL NOT CURL. THE COLLAR SHALL COVER THE

FELLED SEAM AT THE BACK AND THE UNDERCOLLAR

SHALL NOT BE EXPOSED AT THE BOTTOM EDGE. THE

COLLAR SHALL BE CREASED ACROSS THE CENTER BACK

OF THE BREAKLINE AND ROLL PRESSED TO MEET

THE LAPEL.

B. PRESS FRONTS AND COLLAR. PRESS FRONT EDGES

AND COLLAR PRIOR TO REMOVING EDGE BASTING AND

BUTTONHOLE OPERATION. PRESS EDGE OF LAPELS,

FRONT, COLLAR AND BOTTOM OF COAT ON EDGE

PRESSING MACHINE. PRESS BALANCE OF FRONTS,

SIDE SEAMS, AND BACK ON SUITABLE PRESSING

MACHINE. PRESS FRONTS ON WOMEN'S RIGHT AND

LEFT FRONT ON FORM PRESSING MACHINE.

C. PRESS SLEEVES. SLEEVES SHALL BE ROLL

PRESSED. THE SLEEVE HEMS SHALL NOT BE HARD

PRESSED JUST STEAMED. (FOR ALTERATION

PURPOSES).

D. PRESS COLLAR/LAPEL (SEE FIGURE 4).

(1) PRESS THE BREAKLINE OF COLLAR 3 TO 4

INCHES ACROSS THE CENTER BACK. PRESS THE

BREAKLINE OF THE COLLAR AND LAPEL AREA 1

INCH ABOVE AND BELOW GORGE SEAM.

(2) PRESS COLLAR ON COLLAR MACHINE STRETCHING

OUTER EDGE OF COLLAR OVER THE SHOULDER AREA.

COLLAR SHALL BE NEITHER TOO SHORT NOR TOO LONG.

(3) PRESS LAPELS. THE ROLL LINE OF THE LAPELS

SHALL EXTEND A UNIFORM DISTANCE FROM THE GORGE

SEAM. THE LAPELS SHALL BE ROLL PRESSED

STARTING 1 TO 1-1/2 INCHES BELOW GORGE SEAM

TOWARD FIRST BUTTON/BUTTONHOLE.

PAGE 40, TABLE X, at end of table add footnote: “1/ Tolerance shall be ± 1/8 inch for all dimenisons in table.

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG. EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY

SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL

CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC)

MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF

MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF

MIL-DTL-32075.

ADDITIONAL INFORMATION FOR C-F-206:

C-F-206G IS INACTIVE FOR NEW DEISGN AND

IS NO LONGER USED EXCEPT FOR REPLACEMENT

FOR DESIGN OF NEW MATERIALS, USE ASTM-D-2475

THE FELT SHALL NOW CONFORM TO THE ASTM METHODS

WHEN AVAILABLE.

ADDITIONAL INFORMATION FOR A-A-52094A:

NO ADDITIONAL INFORMATION

CHANGES TO V-T-295E:

THREAD, NYLON; V-T-295 DATED AUGUST 1, 1985 IS HEREBY CANCELLED; FUTURE ACQUISITONS SHOULD REFER

TO THREAD, NYLON, A-A-59826 DATED 03 MARCH 2009 AS A REPLACEMENT.

ADDITIONAL INFORMATION FOR A-A-50196:

(NO CURRENT CHANGES TO A-A-50196B)

ADDITIONAL INFO FOR NN-P-71: NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T0829 - 9/11/06)

MIL-DTL 32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL 32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL". UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM".

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSN"s."

ADDITIONAL INFORMATION FOR DDD-T-86:

INTERIM CHANGES TO DDD-T-86H:

NOTE - REDUCED AQLS APPLY AS FOLLOWS:

PAGE 9, LINE 9, DELETE "0.4" AND SUBSTITUTE,

"0.28", FOR MAJORS. DELETE "1.5" AND SUBSTITUTE

"1.0", FOR TOTALS.

COMMERCIAL ITEM DESCRIPTION A-A-52071

DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR

USE IN PLACE 0F DDD-T-86H.

"THE REQUIREMENT FOR THE HERRINGBONE TAPE IS TYPE I, 3/16 INCH WIDTH AND 58 PICKS PER INCH FROM

TABLE I. PHYSICAL REQUIREMENTS."

ADDITIONAL INFORMATION FOR A-A-52071:

TAPE, TEXTILE, COTTON, FOR GENERAL USE.

ADDITIONAL INFORMATION FOR MIL-C-368:

(USE OF IMPORTED YARN AUTHORIZED FOR

CLASS 1 CLOTH)

INTERIM CHANGES TO MIL-C-368J:

PAGE 2, PARA. 1.2, ADD THE FOLLOWING:

"CLASS 4 - TWILL, 3.7 OUNCE, RELAXED FINISH.".

PAGE 3, PARA. 2.2, ADD THE FOLLOWING:

"AATCC 20 - FIBER ANALYSIS: QUALITATIVE"

PAGE 4, TABLE I, UNDER "CLASS" COLUMN, DELETE

"1" AND SUBSTITUTE "1 AND 4".

PAGE 8, ADD THE FOLLOWING NEW SUBPARAGRAPH:

"3.8.1 RELAXED FINISH. CLASS 4 CLOTH SHALL HAVE

A RELAXED FINISH APPLIED ON A TENTER FRAME

DURING THE FINISHING PROCESS.".

PAGE 8, TABLE II, UNDER TEST METHOD COLUMN,

LINE 1, DELETE "1600" AND SUBSTITUTE "AATCC 20".

PAGE 8, TABLE II, ADD THE FOLLOWING:

"SHRINKAGE (CLASS 4) 3.8, 3.8.1 5580".

ADDITIONAL INFORMATION FOR MIL-B-371:

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729 (THE FOLIAGE GREEN 502 AREA OF THE PATTERN), REFERENCED FOR SHADE ONLY. THIS STANDARD IS TEMPORARY UNTIL FURTHER

NOTICE.

INTERIM SPECIFICATION CHANGES TO MIL-B-371F:

PAGE 2, AT THE TOP OF THE PAGE AFTER "CLASS 3" ADD "AND 4". DELETE "CLASS 4 -WATER AND MILDEW-

RESISTANT FINISH 2, 2' METHYLENE BIS (4-CHLOROPHENOL)".

PAGE 3, PARAGRAPH 2.2 OTHER PUBLICATIONS. ADD THE FOLLOWING BELOW "APPLICATION FOR COPIES

SHOULD BE ADDRESSED TO: ASTM

INTERNATIONAL, 100 BARR HARBOR DRIVE, WEST CONSHOHOCKEN, PA. 19428"

"AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS:

QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO: AMERICAN ASSOCIATION OF TEXTILE

CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 4, 3.4 ADD AT THE END OF (SEE 6.2). INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS IDENTIFIED AS ROLL #3721 (THE FOLIAGE GREEN 502 AREA OF THE PATTERN), AND REFERENCED FOR SHADE

ONLY. FOLIAGE GREEN 504 IS TO BE USED AS SPECIFIED BY CONTRACT.

PAGE 4, PARA. 3.3.3, DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING: "3.3.3 POLYPROPYLENE YARN (AS AN ALTERNATIVE FOR TYPES III AND VII BRAID). THE YARN SHALL BE TEXTURED POLYPROPYLENE OF SUITABLE DENIER TO MEET THE REQUIREMENTS OF THIS DOCUMENT. POLYPROPYLENE BRAID IS APPLICABLE

ONLY TO THE ITEMS LISTED IN PARAGRAPH 6.7."

AFTER PARA. 3.3.4: ADD THE FOLLOWING NEW PARA: "3.3.5. 100% TEXTURED POLYESTER(AS AN ALTERNATIVE FOR TYPES I, II, IV, AND VI).THE YARN SHALL BE TEXTURED POLYESTER OF A SUITABLE

DENIER TO MEET THE REQUIREMENTS OF THIS DOCUMENT."

PAGE 5, PARA. 3.5.3 AFTER "CLASS 3" ADD "CLASS 4." AFTER "THE CLASS 3" ADD "AND 4".

PARA. 3.5.4, DELETE IN ITS ENTIRETY.

PAGE 8, ADD THE FOLLOWING TABLE IIA:

"TABLE IIA PHYSICAL REQUIREMENTS FOR POLYESTER BRAID

TYPE DIAMETER WEIGHT PER NUMBER OF ENDS PER

(INCHES) 144 YARDS CARRIERS CARRIER

(OUNCES)

MIN.

II 5/32+/-1/32 28.0 8 1

VII 11/32+/-1/32 25.0 44 1

NUMBER YARN PLY PICKS BREAKING

OF ENDS BRAID CORE PER INCH STRENGTH

IN CORE MIN. (LBS.) MIN.

1/ 8 2 3 10 140

- - - 22 200

1/ UNDYED COTTON CORE YARNS."

PAGE 10, PARA. 4.4.2.1 YARD-BY-YARD EXAMINATION, LINE 9, DELETE "1.5" AND SUBSTITUTE "1.0"

PAGE 13, TABLE V. END ITEM TESTS UNDER REFERENCED TEST METHOD COLUMN, LINES 4 AND 5 DELETE

"1600" AND SUBSTITUTE "AATCC 20"

(ref. T0821 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-B-3461:

MIL-B-3461G BUTTON, INSIGNIA, METAL,

. UNIFORM AND CAP, 9/30/79;

. AMENDMENT 6 DTD 6/24/03

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-P-15011:

NO ADDITIONAL INFORMATION FOLLOWS.

(ref. T1368 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-B-17757:

MIL-B-17757 IS CANCELLED WITHOUT REPLACEMENT.

THE FOLLOWING DOCUMENTS ARE AUTHORIZED FOR USE IN LIEU

OF MIL-B-17757:

ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD SHIPPING CONTAINERS.

(ref. T0857 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-DTL-21115:

CERTIFICATE OF CONFORMANCE IS APPLICABLE FOR

THE GRADE OF WOOL IN THE TOP FORM.

ADDITIONAL INFORMATION FOR MIL-C-43718:

MIL-C-43718C HAS BEEN CANCELLED

A-A-52106 HAS BEEN AUTHORIZED AS A REPLACEMENT

INTERIM SPECIFICATION CHANGES TO MIL-C-43718C:

PAGE 3, PARA. 2.2, ADD THE FOLLOWING:

"AATCC 20 - FIBER ANALYSIS: QUALITATIVE"

PAGE 5, PARA. 3.9, DELETE ENTIRELY AND

SUBSTITUTE: "3.9 SEAM EFFICIENCY. ALL STAPLE

FIBER BASED CLOTH SHALL HAVE A SEAM EFFICIENCY

OF NOT LESS THAN 80 PERCENT; WHEREAS, 100 PER-

CENT TEXTURIZED FILAMENT POLYESTER SHALL HAVE

A SEAM EFFICIENCY OF NOT LESS THAN 70 PERCENT

WHEN TESTED AS SPECIFIED IN 4.4.3."

PAGE 8, TABLE II, UNDER TEST METHOD COLUMN,

LINE 1, DELETE "1600" AND SUBSTITUTE "AATCC 20".

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD SAMPLE FOR SHADE. CLASS 5

FABRIC IS MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-C-44121:

A-A-52106 HAS BEEN AUTHORIZED IN PREFERENCE TO

MIL-C-44121

NOTE 1: THE SUBLIMATION TESTING REQUIREMENT

SHOWN IN PARAGRAPH 3.5.2 OF AM. #1 DOES NOT

APPLY TO AIR FORCE PROCUREMENTS OF AIR FORCE

SERVICE COATS FOR MALES AND FEMALES.

NOTE 2. FOR NAVY OR COAST GUARD PROCUREMENTS

REFERENCING BLUE SHADE 334, SUBLIMATION

REQUIREMENT OF PARA. 3.5.2 OF AM. #1 IS NOT

APPLICABLE.

INTERIM SPECIFICATION CHANGES TO MIL-C-44121:

AMENDMENT NO. 1, PAGE 2

UNDER PAGE 7, FOOTNOTE 4/:DELETE AND SUBSTITUTE:

"4/ THE TEST SHALL BE PERFORMED AT 325 DEG

F. +- 6 DEG F.."

PAGE 7 OF MIL-C-44121:

TABLE II, UNDER TEST METHOD, ACROSS FROM

DIMENSIONAL STABILITY: DELETE "5556 3/"

AND SUBSTITUTE "5580".

FOOTNOTE "3/": DELETE IN ITS ENTIRETY.

(Ref. T1685)

ADDITIONAL INFORMATION FOR MIL-C-44192:

INTERIM CHANGES TO MIL-C-44192:

PAGE 4, PARA 3.2.4 AFTER "II" ADD "FOR DRESS

COATS AND TYPE "III" FOR ALL WEATHER COATS."

PAGE 11, PARA 30.4, DELETE AND SUBSTITUTE:

"30.4 CONTAINER CLOSURE. THE CONTAINER SHALL BE

CLOSED BY THE USE OF 3 INCH WIDE TAPE CONFORMING

TO TYPE II, CLASS 2 OF PPP-T-45. THE TAPE SHALL

BE CENTERED OVER EACH EXPOSED SEAM INCLUDING

THE DISPENSING DOOR SLITS AND EXTENDED OVER ALL

THE CORNERS AND EDGES WITH A MINIMUM OF 2 INCHES

ONTO THE ADJACENT BOX PANELS. THE MANUFACTURERS

JOINT AND THE EDGES AROUND THE BOTTOM OPENING

OF THE LID AFTER IT IS PLACED OVER THE

CONTAINER BOX BODY NEED NOT BE TAPED.".

NOTE: WHEN HANGER PACKS ARE SPECIFIED FOR ALL-

WEATHER COATS, COATS SHALL BE PACKAGED, MARKED

AND PALLETIZED IN ACCORDANCE WITH MIL-C-44192,

WITH FRONTS LAPPING AND BUTTONED.

THE FOLLOWING APPLIES:

TEN (10) COATS OF ONE CLASS AND SIZE SHALL BE

PACKED IN A TYPE I CONTAINER (HANGER PACK)

EXCEPT THAT THE DIMENSIONS OF THE CONTAINER

SHALL APPROXIMATE 24 X 21 INCHES AND THE DEPTH

OF THE CONTAINER SHALL BE 48 +0/-2 INCHES.

HANGER PACK SHIPPING CONTAINERS SHALL BE

MARKED A/C TO IDENTIFY THE LEVELS OF PACKAGING/

PACKING.

(Ref. T0806)

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1" INSERT

"TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X - CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT LISTED IN THE DODISS SHALL BE THE ISSUES OF THE

NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO AMERICAN ASSOCIATION OF TEXTILE

CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR KNIT.

WHEN SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1. TYPE X1 SHALL BE STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF CHAINSTITCHING IS SEWN IN THE MACHINE DIRECTION OF THE

SUBSTRATE IN ORDER TO REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING CHAINSTITCH STITCH TYPE

WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS FUSIBLE SEAM

TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24, DELETE "45" AND

SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND 3 DELETE "1600" AND

SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER LAUNDERING/DRY CLEANING). DELETE THE FIRST AND SECOND SENTENCES IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR

CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL PART FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL STABILITY

AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE FOLLOWING BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES, OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED TO DETERMINE IF DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

ADDITIONAL INFORMATION FOR FED-STD-191

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING

FED-STD-191. SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM.

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL STANDARDS ISO 9001:2000

OR AMERICAN SOCIETY FOR QUALITY ASQ 2003 VERSION.

HIGHER LEVEL INSPECTION SYSTEM:

THE INSPECTION SYSTEM(S) MUST BE SUBMITTED WITH YOUR

BID PROPOSAL FOR EVALUATION AND APPROVAL BY DLA TROOP

SUPPORT'S CONTRACTING OFFICER.

INSPECTION SYSTEM(S) COMPLIANT/BUT ARE NOT

LIMITED TO THE INTERNATIONAL STANDARDS ISO 9002

OR ASQ 2003 MAY BE UTILIZED IF TAILORED TO THE SPECIFIC

QUALITY ASSURANCE REQUIREMENTS IN THIS SOLICITATION.

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN

CANCELLED AND REPLACED BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

TO FED-STD-751.

(ref. T0216 - May 18, 2006)

ADDITIONAL INFORMATION FOR ASTM-D-6193(2004)OR LATEST VERSION:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T8068 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2

24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2 INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

NOTE: MIL-STD-105 HAS BEEN CANCELLED AND REPLACED

BY THE FOLLOWING: "AMERICAN NATIONAL STANDARDS

INSTITUTE (ANSI) ANSI/ASQC Z1.4 - SAMPLING

PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES".

APPLICATION FOR COPIES SHOULD BE OBTAINED FROM:

AMERICAN SOCIETY FOR QUALITY CONTROL

611 EAST WISCONSIN AVE

MILWAUKEE, WI 53202

MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR

SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE

OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN.

NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR MIL-STD-1608:

INTERIM CHANGES TO MIL-STD-1608C:

PAGE 14, BEFORE "COAT BUTTONED ON FORM" ADD "B."

PAGE 17: DEFECT E.4., LINE 1, AFTER "TO" ADD

"ROLL OUTWARD AND NOT".

PAGE 19: TABLE II, AFTER DEFECT XXI SLEEVE PARA.

E. ADD "NOTE: THE NORMAL HANGING POSITION FOR

THE FRONT EDGE OF THE SLEEVE IS THE CENTER OF

THE TOP EDGE OF THE LOWER PATCH POCKET."

PAGE 22: BEFORE "XXIX", ADD "C. COAT SPREAD OUT

ON TABLE"

PAGE II, ADD NEW DOCUMENT "MIL-C-29628 (NU)

COAT, WOMEN'S, BLUE DRESS".

MIL-STD-1608C PAGE 7, TABLE I DELETE IN ITS

ENTIRETY AND SUBSTITUTE "TABLE I SAMPLING

PROVISIONS".

NORMAL INSPECTION

LOT SZ SAMP SZ MAX ACCP MAX ACCP PT VALU

. NO. FOR

. SELECTED 3&2 PT 3,2,1 PT

. (*DEFECT) DEFECTS DEFECTS

UP THRU 90 20 0 3 7

91- 150 32 0 4 11 151-280 50 0 7 13 281-500 80 0 9 19 501-1200 125 1 14 27 1201-3200 200 1 18 36 3201-10,000 315 2 25 55 10,001-35,000 500 3 36 81

35,001 & OVER 800 5 55 122

TIGHTENED INSPECTION

UP THRU 90 20 0 3 5

91-150 32 0 3 7 151-280 50 0 5 11 281-500 80 0 7 14 501-1200 125 1 11 21 1201-3200 200 1 13 31 3201-10,000 315 2 22 47 10,001-35,000 500 3 33 69

35,001 & OVER 800 5 49 104

REDUCED INSPECTION

UP THRU 280 20 0 2-4 7

281-500 32 0 3-7 12 501-1200 50 0 6-10 15 1201-3200 80 0 7-10 24 3201-10,000 125 1 13-18 31 10,001-35,000 200 1 17-23 47

35,001 & OVER 315 2 23-29 69

NOTE: FOR THE REDUCED POINT VALUES OF THE

REDUCED INSPECTION ON 3 & 2 POINT DEFECTS. IF

THE FIRST VALUE IS EXCEEDED, BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

(Ref. T0344)

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS