Marine Corps Belt Mens Green pgc02051_aa55222_beltv5.pdf

BELT, COAT, MAN'S, POLYESTER/WOOL GABARDINE, GREEN 2212 SHALL BE MADE IN

ACCORDANCE WITH A-A-55222 DATED 06 JULY 1993

PATTERN DATE: 28 JULY 1993

STANDARD SAMPLE FOR CLOTH, POLY/WOOL GABARDINE

10.6 OZ., GREEN SHADE 2212 CONFORMING TO TYPE

II, CLASS 12 OF MIL-DTL-10176 IS AVAILABLE ON ROLL

NO. 3935 FOR SHADE, FINISH & COLORFASTNESS.

ADDITIONAL INFORMATION FOR A-A-55222:

PAGE 2 BASIC MATERIAL

DELETE BASIC MATERIAL PARAGRAPH AND TABLE I- BASIC MATERIAL REQUIREMENTS IN

ITS ENTIRETY AND SUBSTITUTE "THE BASIC MATERIAL SHALL BE CLOTH,

POLYESTER/WOOL GABARDINE, GREEN, SHADE 2212, CONFORMING TO CLASS I OF MIL-

DTL-10176.

PAGE 3 BELT FASTENER MATERIAL

LINE 2 DELETE "MULTIFILAMENT RAYON" AND SUBSTITUTE "LINING"

LINE 3 DELETE "2208" AND REPLACE WITH "2212"

PAGE 5 THREAD

SILK THREAD

LINES 1-3 DELETE "The silk thread....shall not apply. Silk thread..." AND SUBSTITUE "Thread" at the end of the paragraph insert:

Silk thread replacement. The following threads are to be used as a substitute in place of silk threads for the outlined operations."

Thread Replaced Operation T-40 A-Silk For all seaming and topstitching B & F Nylon B & F Silk Buttonholes B Nylon B Silk Eyelets 0 Nylon 0 Silk Felling

PAGE 5 COTTON THREAD

LINE 2 DELETE "TYPE III,....3-PLY" AND SUBSTITUTE "COTTON COVERED POLYESTER

70/2".

PAGE 5 BUTTONS

LINE 3 after "NO. 62017" add "or a green that is good match to the basic material".

PAGE 5 LABEL/TAG

LINE 2 DELETE "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075"

PAGE 8, PRESERVATION, PACKING, AND MARKING AT THE END OF THE PARAGRAPH ADD

THE FOLLOWING:

EACH BELT SHALL BE FOLDED IN HALF AND THEN FOLD-

ED IN HALF AGAIN. THE SIZE MARKING SHALL BE

VISIBLE WHEN EACH BELT IS FOLDED. THE FOLDED

BELTS SHALL BE STACKED AND TIED INTO BUNDLES

APPROXIMATELY 1 INCH FROM EACH END WITH STRONG

TWINE OR COTTON TAPE. EACH BUNDLE SHALL

CONTAIN 10 BELTS OF ONE SIZE ONLY.

FOR DEPOT SHIPPING, ONE HUNDRED TWENTY (120) OF

ONE SIZE ONLY SHALL BE PACKAGED AS ABOVE, AND PACK-

ED IN A FIBERBOARD SHIPPING CONTAINER WITH LINER

CONFORMING TO CLASS DOMESTIC, TYPE CF, VARIETY SW, GRADE 200,

STYLE RSC-L, WITH DW LINER".

(Ref. W2051)

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE

FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR

PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD

BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO

ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND

SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE

BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT

CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST

APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO

HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE

ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL

CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL

PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN

APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE

SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE

VIII (TAG, PAPER) OF MIL-DTL-32075.

ADDITIONAL INFORMATION FOR MIL-DTL-10176:

INTERIM SPECIFICATION CHANGES TO MIL-DTL-10176K:

3.7.3, LINE 2: DELETE "5.5" AND SUBSTITUTE "5.0"

ADD THE FOLLOWING PARAGRAPHS:

"3.7.4 WATER REPELLENT TREATMENT. WHEN SPECIFIED

, THE CLOTH SHALL BE GIVEN AN APPROVED DURABLE

FLUOROCHEMICAL TYPE WATER REPELLENT TREATMENT

AND SHALL CONFORM TO THE REQUIREMENTS

SPECIFIED IN 3.7.2 WHEN TESTED AS SPECIFIED IN

4.4.4.

3.7.4.1 SPRAY RATING. THE RESULTS OF THE THREE

INDIVIDUAL DETERMINATIONS ON THE SAMPLE UNIT FOR

SPRAY RATING SHALL BE EQUAL TO OR BETTER THAN

RATINGS OF 90,90,80 INITIALLY AND 80,80,70 AFTER

ONE DRYCLEANING WHEN TESTED AS SPECIFIED IN

4.4.4."

PAGE 9, PARAGRAPH 4.3.3.1 YARD-BY-YARD

EXAMINATION, LINE 3, DELETE "10" AND SUBSTITUTE

"7", LINE 4, DELETE "12" AND SUBSTITUTE "8"

TABLE II, BELOW "PH": ADD THE FOLLOWING UNDER

THEIR RESPECTIVE COLUMNS:

"WATER REPELLENCY:

SPRAY RATING:

INITIAL--------3.7.3.1---------5526

AFTER 1 DRYCLEANING----3.7.3.1---5508 AND 5526

SPONGING:

COLD WATER SPONGING IS REQUIRED. A PROPER

ALCOHOL WETTING AGENT SHALL BE USED TO INSURE

SHRINKAGE IS ACCOMPLISHED AND WATER RESISTANT

FINISH IS NOT RELEASED.

THE WATER REPELLANT TREATMENT MUST BE

APPLIED BEFORE THE SPONGING OPERATION.

ALL THE SPECIFICATION REQUIREMENTS MUST BE MET.

CODE OF FEDERAL REGULATIONS

16 CFR PART 1500- FEDERAL HAZARDOUS SUBSTANCES

ACT REGULATIONS.

29 CFR PART 1910- OCCUPATIONAL SAFETY AND HEALTH

STANDARDS.

(APPLICATIONS FOR COPIES OF REFERENCED

DOCUMENTS SHOULD BE ADDRESSED TO U.S

GOVERNMENT PRINTING OFFICE, SUPERINTENT OF

DOCUMENTS, MAIL STOP: SSOP, WASHINGTON, DC

20402-9328.)

PRINCIPLES AND METHODS OF TOXICOLOGY,

A. WALLACE HAYES (EDITOR), 1989, PP 394-396.

(APPLICATIONS FOR COPIES OF REFERENCED

DOCUMENTS SHOULD BE ADDRESSED TO RAVEN

PRESS,1185 AVENUE OF THE AMERICAS, NEW YORK,

NY 10036.)

TOXICITY. THE FINISHED CLOTH SHALL NOT

PRESENT A DERMAL HEALTH HAZARD WHEN USED

AS INTENDED.

TOXICITY ASSESSMENT. THE CONTRACTOR MUST

FURNISH INFORMATION WHICH CERTIFIES THAT

THE FINISHED PRODUCT IS COMPOSED OF MATERIALS

WHICH HAVE BEEN SAFELY USED COMMERCIALLY OR

PROVIDE SUFFICIENT TOXICITY DATA TO SHOW

COMPATIBILITY WITH PROLONGED, DIRECT SKIN

CONTACT. AT A MINIMUM, TOXICITY DATA SHOULD

INCLUDE RESULTS FROM A PRIMARY DERMAL IRRITATION

STUDY IN LABORATORY ANIMALS AND A REPEATED

INSULT HUMAN PATCH TEST (MODIFIED DRAIZE

PROCEDURE). THE LATTER MUST BE CONDUCTED UNDER

THE SUPERVISION OF A QUALIFIED DERMATOLOGIST

USING AT LEAST 100 FREE LIVING INDIVIDUALS.

(REF. T0969)

ADDITIONAL INFORMATION: INTERIM CHANGES TO A-A-50186:

PAGE 1:

PARA. 1.1 TYPES, NEXT TO TYPE V NON-WOVEN ADD

"(MEDIUM WEIGHT)", UNDER TYPE V ADD "TYPE VI

NON-WOVEN (LIGHT WEIGHT)".

PARAGRAPH 2.1, LINE 5. GENERAL.: DELETE

"SATURATION BONDED WITH ACRYLIC TYPE BINDER"

AND SUBSTITUTE "EITHER WET-LAID, SATURATION BONDED OR THERMAL BONDED".

PAGE 2:

TABLE 1. PHYSICAL REQUIREMENTS (WOVEN) UNDER TEST

METHOD COLUMN, LINE 3 DELETE "1600" AND SUBSTITUTE

"AATCC 20 3/".

TABLE I. PHYSICAL REQUIREMENTS (WOVEN) AT BOTTOM OF

PAGE UNDER FOOTNOTE 2/ ADD THE FOLLOWING: "3/ AMERICAN ASSOCIATION OF

TEXTILE CHEMISTS AND COLORISTS

TEST METHOD."

PAGE 3, TABLE II, PHYSICAL REQUIREMENTS (NONWOVEN) UNDER

TYPE V, AND VI, ACROSS "CONSTRUCTION": DELETE "WET-LAID"

AND "WET-LAID OR SATURATE, THERMAL BONDED" AND SUBSTITUTE

"SEE 2.1" FOR BOTH TYPES.

TABLE II, UNDER TYPE VI: ADD UNDER EACH CHARACTERISTIC:

"1.5, 12, 8, 2.5, 2.5, WET-LAID OR SATURATE THERMAL BONDED" RESPECTIVELY.

PAGE 3, PARA. 3.2 FINISH. LINE 1 DELETE "AN APPROVED" AND SUBSTITUTE " A

COMMERCIALLY ACCEPTED".

PAGE 5: ADD THE FOLLOWING: "5.7 SUPER SESSION DATA.

THE TYPES OF CLOTH COVERED BY THIS COMMERCIAL ITEM

DESCRIPTION REPLACE TYPES COVERED BY CCC-C-438 AS FOLLOWS:

A-A-50186 CCC-C-438

TYPE I TYPE I, CLASSES 1 AND 2

TYPE II TYPE II, CLASS 1

TYPE III TYPE III, CLASS 1

TYPE IV TYPE III, CLASS 2

TYPE V TYPE IV, CLASS 1

TYPE VI TYPE IV, CLASS 2"

(ref. T1034 - May 19, 2006)

ADDITIONAL INFORMATION FOR A-A-52094A THREAD, COTTON

NO ADDITIONAL INFORMATION

(ref. T1481)

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20"

AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN

CANCELLED AND REPLACED BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

TO FED-STD-751.

(ref. T0216 - May 18, 2006)