Marine Corps Coat Womens Green pgc02271_coatv4.pdf

COAT, WOMAN'S: POLYESTER/WOOL, GABARDINE, GREEN 2212 SHALL BE MADE IN ACCORDANCE WITH MIL-C- 29427 dated 21 NOVEMBER 1994

PATTERN DATE: 5 SEPTEMBER 2007

INTERIM SPECIFICATION CHANGES TO MIL-C-29427B:

STANDARD SAMPLE OF CLOTH, POLY/WOOL GABARDINE, 10.6 OZ, GREEN SHADE 2212 CONFORMING TO TYPE

II, CLASS 12 OF MIL-DTL-10176 IS AVAILABLE ON ROLL NO.3935 FOR SHADE, FINISH AND

COLORFASTNESS.

PAGE 2, PARAGRAPH 2.1.1,

UNDER "SPECIFICATIONS FEDERAL",

DELETE DDD-T-86 - TAPE, TEXTILE, COTTON, GENERAL PURPOSE (UNBLEACHED, BLEACHED, OR DYED) AND

SUBSTITUTE "A-A-52071 - TAPE, TEXTILE, COTTON, GENERAL PURPOSE".

DELETE V-T-295 THREAD, NYLON" AND INSERT A-A-59826 THREAD, NYLON.

DELETE DDD-L-20 - LABEL, FOR CLOTHING, EQUIPAGE, AND TENTAGE, GENERAL USE)

INSERT A-A-52105- CLOTH, INTERLINING, COTTON OR SYNTHETIC, WARP, AND SPUN HAIR WOOL OR RAYON.

UNDER "SPECIFICATIONS MILITARY"

DELETE MIL-C-297- CLOTH INTERLINING, COTTON WARP, AND SPUN HAIR-WOOL FILLING

INSERT "MIL-DTL-32075- LABEL, FOR CLOTHING, EQUIPAGE, AND TENTAGE, (GENERAL USE)#.

DELETE MIL-C-368 - CLOTH, SATIN, RAYON AND CLOTH, TWILL, RAYON

DELETE MIL-C-10176" AND INSERT "MIL-DTL-10176.

DELETE MIL-B-17757.

PAGE 3, PARAGRAPH 2.1.1,

UNDER "STANDARDS FEDERAL"

DELETE FED-STD-191 - TEXTILE TEST METHODS

DELETE FED-STD-751 - STITCHES, SEAMS AND STITCHINGS.

UNDER "STANDARDS MILITARY",

REINSTATE MIL-STD-147 - PALLETIZED UNIT LOADS

DELETE *MIL-STD-731 - QUALITY OF WOOD MEMBERS AND CONTAINERS AND PALLETS"

PAGE 4, PARAGRAPH 2.2, UNDER "AMERICAN SOCIETY

FOR TESTING AND MATERIALS (ASTM),

INSERT THE FOLLOWING TEST METHODS:

ASTM D 747 APPARENT BENDING MODULUS OF PLASTICS BY MEANS OF A CANTILEVR BEAM

ASTM D 1974 STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD

SHIPPING

ASTM D 3775 FABRIC COUNTS OF WOVEN FABRIC

ASTM D 3776 MASS PER UNIT AREA (WEIGHT) OF FABRIC

ASTM D 5034 BREAKING FORCE AND ELONGATION OF

TEXTILE FABRICS (GRAB TEST)

ASTM D 5118 STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES

ASTM D 6193 STITCHES AND SEAMS

ASTM D 6199 WOOD MEMBERS OF CONTAINERS AND QUALITY OF"

LINE 4, AFTER "TESTING MATERIALS#, DELETE

THE ADDRESS AND SUBSTITUTE "100 BARR HARBOR

DRIVE, WEST CONSHOHOCKEN, PA 19428-2959"

PAGE 4, PARAGRAPH 2.2, INSERT THE FOLLOWING DOCUMENTS:

"AMERICAN ASSOCIATION OF TEXTILE CHEMISTS

AND COLORISTS (AATCC) AATCC TECHNICAL MANUAL:

8-COLORFASTNESS TO CROCKING

15-COLORFASTNESS TO PERSPIRATION

132-COLORFASTNESS TO DRYCLEANING

158- Dimensional Changes on Drycleaning in Perchloroethylene:

Machine Method

(APPLICATION FOR COPIES SHOULD BE ADDRESSED

TO AMERICAN ASSOCIATION OF TEXTILE CHEMISTS

AND COLORISTS, P.O. BOX 12215, RESEARCH

TRIANGLE PARK, NC 27709).

AMERICAN SOCIETY FOR QUALITY CONTROL

ANSI/ASQC Z1.4 AMERICAN NATIONAL STANDARD

SAMPLING PROCEDURES AND TABLES FOR

INSPECTION BY ATTRIBUTES

(APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO

AMERICAN SOCIETY FOR QUALITY CONTROL, P.O. BOX

3005, 611 E. WISCONSIN AVENUE, MILWAUKEE, WI53201-4606).

PAGE 5 PARAGRAPH 3.3.2, DELETE IN ITS ENTIRETY

AND SUBSTITUTE THE FOLLOWING PARAGRAPH:

"3.2.2.LINING- THE MATERIAL FOR LINING THE

COATS SHALL BE A TWILL OR SATIN, SOLUTION

OR PIECE DYED ACETATE CLOTH, CONFORMING TO THE

REQUIREMENTS IN TABLE AI. THE SHADE OF LINING MATERIAL SHALL BE

A GOOD MATCH TO THE BASIC MATERIAL.”

PAGE 5, PARAGRAPH 3.3.4, AT END OF PARAGRAPH,

INSERT: "AS AN ALTERNATE, THE MATERIAL MAY BE

100 PERCENT POLYESTER, NEEDLE-PUNCHED NON-WOVEN

MATERIAL, WEIGHING BETWEEN 8.0 AND 10.0 OZ./

SQUARE YARD WITH A THICKNESS BETWEEN 0.070 AND

0.095 INCH AT 0/6 PSI AND EXHIBITING A CROSS-

MACHINE DIRECTION STIFFNESS OF 0.05 LOAD POUNDS

(MINIMUM) IN ACCORDANCE WITH ASTM-D-747 (VOL. 8.01),

APPARENT BENDING MODULUS OF PLASTICS BY MEANS OF

A CANTILEVER BEAM. THE COLOR OF THE UNDERCOLLAR

MATERIAL SHALL BE GREEN THAT CLOSELY MATCHES THE

BASIC MATERIAL."

PAGE 5, PARAGRAPH 3.3.5, LINE 4, DELETE: "METHOD

5580 OF FED-STD-191" AND SUBSTITUTE "AATCC 158".

PAGE 5, PARAGRAPH 3.3.7, LINE 1, DELETE "TYPE III"

AND SUBSTITUTE "TYPE II"; LINE 2, DELETE

"DDD-T-86" AND SUBSTITUTE "A-A-52071".

PAGE 5, PARAGRAPH 3.3.9, SHOULDER PADS

AT END OF THE PARAGRAPH ADD "AN ALTERNATE PAD

MAY BE USED CONFORMING TO THE REQUIREMENTS

OF "INSERT B" IN THE INTERIM CHANGES TO MIL-P-15064."

PAGE 6, PARAGRAPH 3.3.11.1, DELETE IN ITS ENTIRETY AND SUBSTITUTE “3.3.11.1 fusible interlining FOR SMALL PARTS. THE COLLAR, FULL FRONT FACINGS, SHOULDER STRAPS, AND CUFFS SHALL USE A BLACK OR CHARCOAL, NONWOVEN FUSIBLE INTERLINING. IT SHALL CONFORM TO EITHER TYPE

V, CLASS 1, STYLE B OF MIL-C-44296.”

PAGE 6, PARAGRAPH 3.3.11.2, DELETE IN ITS ENTIRETY AND SUBSTITUTE “3.3.11.2 FUSIBLE COAT FRONTS. THE FUSIBLE INTERLINING FOR THE COAT FRONTS AND CENTER BACK VENT SHALL BE A BLACK OR CHARCOAL, NAPPED, WOVEN TWILL MATERIAL CONFORMING TO TYPE III, CLASS 1, STYLE B OF MIL-C-

44296. AS AN ALTERNATE, STYLE NO. T3G WEFT INSERTED KNIT OR EQUAL MAY BE USED.

THE FUSING CONDITIONS SHALL BE AS DIRECTED BY THE SUPPLIER.

PAGE 6, PARAGRAPH 3.3.12 HANGER BRAID.

LINE 2 DELETE "OR RAYON"

AT THE END OF THE PARAGRAPH ADD "AS AN ALTERNATE COLOR, BLACK MAY

BE USED".

Page 6, PARAGRAPH 3.3.13.1: Delete and substitute:

"3 3.13.1 Silk thread replacement. The following threads are to be used as a substitute in place of silk threads for the outlined operations."

Thread Replaced Operation T-40 A-Silk For all seaming and topstitching B & F Nylon B & F Silk Buttonholes B Nylon B Silk Eyelets 0 Nylon 0 Silk Felling

PAGE 6, PARAGRAPH 3.3.13.2 COTTON THREAD

DELETE IN ITS ENTIRETY AND SUBSTITUTE: “3.3.13.2 THE COTTON THREAD SHALL CONFORM TO TYPE I OF A-A-50199, TEX 50, 2 OR 3 PLY MAY BE USED. THE THREAD FOR BASTING SHALL BE A GOOD COMMERCIAL

GRADE COTTON.”

PAGE 6, PARAGRAPH 3.3.13.3 NYLON THREAD, LINE 2, DELETE "V-T-295" AND INSERT "A-A-59826".

PAGE 7, PARAGRAPH 3.3.13.5 LINE 3 AFTER "SEWING THREADS)" ADD "OR A GREEN THAT IS GOOD MATCH

TO THE BASIC MATERIAL.

PAGE 7, PARAGRAPH 3.3.14, GIMP, DELETE THE FIRST SENTENCE AND SUBSTITUTE THE FOLLOWING: "THE BUTTONHOLE GIMP SHALL BE COTTON, CONFORMING TO SOFT FINISH (TYPE I) OR GLAZED FINISH (TYPE

II) OF A-A-50198".

LINE 3, AFTER "CABLE NO. 66023" ADD "OR A GREEN THAT IS A GOOD MATCH TO THE BASIC MATERIAL.

PAGE 7, PARAGRAPH 3.3.16.1 IDENTIFICATION LABEL

LINE 2, "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075".

OR AS AN ALTERNATE THE USE OF 4800 WT

POLYESTER LABELING TAPE IS APPROVED".

AT THE END OF THE PARAGRAPH, DIRECTLY BELOW

“FIBER CONTENT" ADD NEW LINE "DRY CLEAN ONLY".

PAGE 7, PARAGRAPH 3.3.16.2

LINE 2, DELETE "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075".

LINE 3 DELETE "BODY DIMENSIONS" AND SUBSTITUTE "HEIGHT RANGES" AND DELETE "HEIGHT RANGES"AND

SUBSTITUTE "BODY DIMENSIONS".

PAGE 8, PARAGRAPH 3.3.16.3

LINE 2, DELETE "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075".

PAGE 8 AFTER PARAGRAPH 3.3.16.3, ADD THE FOLLOWING NEW PARAGRAPH: "3.3.16.4 DLA TROOP SUPPORT EXCLUSIVE LABEL - EACH COAT SHALL CONTAIN THE EXCLUSIVE LABEL. THE JACQUARD WOVEN EXCLUSIVE LABEL SHALL INCORPORATE THE DLA LOGO (ATTACHED) AND SHALL SPECIFY "MADE EXCLUSIVELY FOR DEFENSE LOGISTICS AGENCY" AND SHALL INCLUDE "BY" AND THE CONTRACTOR'S NAME. THE LABEL SHALL BE POSITIONED CENTERED AND SEWN ABOVE THE INSTRUCTION LABEL ON THE INSIDE LEFT FRONT LINING.

THE LABEL SHALL BE APPROXIMATELY 2 INCHES SQUARE AND SEWN ON ALL FOUR SIDES. THE PROPOSED FINISHED LABEL'S DESIGN SHALL BE SUBMITTED TO THE CONTRACTING OFFICER FOR APPROVAL."

PAGE 8, PARAGRAPH 3.4, LINE 4, DELETE

"SIMULATED BREAST POCKET WITH OUTSIDE WELT"

PAGE 8, TABLE I, UNDER “PATTERN PARTS” COLUMN FOR “POLYESTER/WOOL GABARDINE”, DELETE "POCKET

WELT” AND UNDER CORRESPONDING “CUT PARTS” COLUMN DELETE “1".

PAGE 8, TABLE I, UNDER PATTERN PARTS, DELETE

"POCKET WELT" AND UNDER CUT PARTS DELETE "1".

PAGE 9, PARAGRAPH TABLE I, UNDER “MATERIALS” COLUMN, DELETE "CLOTH, TWILL, RAYON" AND

SUBSTITUTE "CLOTH, TWILL, ACETATE LINING"

PAGE 9, PARAGRAPH 3.6.1, LINE 2, DELETE "FED-STD-751"

AND SUBSTITUTE "ASTM D 6193".

PAGE 11, TABLE II, OPERATION 1 c, LINE 5-9 DELETE

"THE WELT...PATTERNS FURNISHED.”

PAGE 11, TABLE II, OPERATION 1 d, LINE 3, DELETE

"RAYON" AND LINE 5, DELETE "RAYON".

PAGE 12, TABLE II, OPERATION 1 f, LINE 2, DELETE "cotton warp spun hairwool filling cloth" AND SUBSTITUTE

"MATERIAL".

PAGE 13, TABLE II, OPERATION 3 b, LINE 4, DELETE "RAYON"

PAGE 14, TABLE II OPERATION 4 f, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 14, TABLE II OPERATION 4 f, UNDER COLUMN- SEAM/STCH TYPE DELETE "BSm-2(a) AND SUBSTITUTE "SIMILAR TO SSe-2(a)" PAGE 17, TABLE II OPERATION 6 g, UNDER COLUMN- THREAD NDL BOB/LPR, DELETE "SILK" IN BOTH

PLACES AND SUBSTITUTE "B NYLON", IN BOTH PLACES

PAGE 19, TABLE II OPERATION 9 JOIN CUFF TO SLEEVE, UNDER

"FINISHED APPEARANCE", LINE 2, AFTER "CUFFS"

INSERT "SHALL BE PROPERLY FORMED AND CREASED

AND". BEFORE OPERATION 9A, INSERT NEW OPERATION/ STEP

9A.: "POSITION THE FUSIBLE INTERLINING ON THE

BACK SIDE OF CUFF AND FUSE."

RE-LETTER THE STEPS “9a” to “9b” AND “9b” to “9c”.

PAGE 19, TABLE II OPERATION 9 b, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "A A (SILK) OR 0

0(SILK) AND SUBSTITUTE "(T-40)" OR "(O NYLON)".

PAGE 23, TABLE II OPERATION 14 c, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "(SILK)" AND SUBSTITUTE "(O NYLON)".

PAGES 23 & 24 OPERATION 15, DELETE ENTIRELY.

PAGE 30, TABLE II OPERATION 26 a, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "A A (SILK) AND

SUBSTITUTE "T-40"

PAGES 32 & 33 OPERATION 29, DELETE ENTIRELY.

PAGE 42, TABLE II OPERATION 43 a, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 42, TABLE II OPERATION 44 a, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE ALL THREE

REFERENCES TO "SILK" AND SUBSTITUTE "O NYLON".

PAGE 42 & 43, TABLE II OPERATION 45 b, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE ALL THREE

REFERENCES TO "SILK" AND SUBSTITUTE "O NYLON".

PAGE 43, TABLE II OPERATION 45 c, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 47, TABLE II OPERATION 54 a, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 48, TABLE II OPERATION 55 b, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 48, TABLE II OPERATION 56 a, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 49, TABLE II OPERATION 58 a, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE ALL THREE REFERENCES TO "SILK" AND SUBSTITUTE "T-40" FOR THE FIRST TWO REFERENCES AND "O NYLON" FOR THE

LAST REFERENCE.

PAGE 49, TABLE II OPERATION 58 b, UNDER COLUMN -THREAD NDL BOB/LPR, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 52 OPERATION 64 b, IN “STCH TYPE” COLUMN AFTER “HAND” ADD

"OR 301" AND IN THREAD COLUMN DELETE "(SILK)"

AND SUBSTITUTE "(T-40)".

PAGE 53 OPERATION 66 a, AFTER-“or” IN “STCH IN” COLUMN, DELETE “10-14” AND INSERT “10-12”.

PAGE 53 OPERATION 66 a, IN “STCH TYPE” COLUMN AFTER “HAND” ADD

"OR 301" AND IN THREAD COLUMN DELETE "(SILK)"

AND SUBSTITUTE "(T-40)".

PAGE 53 OPERATION 67 b, IN “STCH TYPE” COLUMN AFTER “HAND” ADD

"OR 301" AND IN THREAD COLUMN DELETE "(SILK)"

AND SUBSTITUTE "(T-40)".

PAGE 56, TABLE II OPERATION 68 b, UNDER COLUMN ““THREAD NDL BOB/LPR”, DELETE "(SILK)" AND SUBSTITUTE "B & F NYLON".

PAGE 56, TABLE II OPERATION 68 c, UNDER COLUMN ““THREAD NDL BOB/LPR”, DELETE "SILK" AND

SUBSTITUTE "T-40".

PAGE 62, PARAGRAPH 4.5, LINE 2, DELETE "MIL-STD-105"

SUBSTITUTE "ANSI/ASQC-Z1.4"

PAGE 63, PARA, 4.5.1, AT THE END OF THE PARAGRAPH

INSERT THE FOLLOWING:

"TESTING SHALL BE PERFORMED ON THE COMPONENTS

LISTED IN TABLE IV FOR CHARACTERISTICS NOTED

PAGE 64, PARAGRAPH 5.1.1, AT END OF PARAGRAPH ADD THE

FOLLOWING: "WHERE HANGER PACKS ARE SPECIFIED,

SEE PARAGRAPH 5.1.3."

PAGE 65, PARAGRAPH 5.2.2, LINE 3-4 DELETE “CONFORMING TO TYPE”... MIL-B-17757”.

PAGE 65, PARAGRAPH 5.2.2, AT END OF PARAGRAPH ADD THE

FOLLOWING: "WHERE HANGER PACKS ARE

SPECIFIED, SEE PARAGRAPHS 5.2.4 AND 5.1.3."

(Ref. W2271)

ACETATE LINING CHANGES REPLACEMENT FOR RAYON

(FOR MARINE CORPS DRESS UNIFORMS)

TABLE AI. LINING MATERIAL.

CHARACTERISTIC REQUIREMENT VERIFICATION

. PARAGRAPH

. TWILL SATIN

YARNS PER INCH (MIN.)

WARP 120 288 4.5.1

FILLING 68 68 4.5.1

WEIGHT -OZ/YD 3.8 4.9 4.5.1

(MIN.)

BREAKING STRENGTH (LBS.,

(MIN)

DRY

WARP 74 83 4.5.1

FILLING 49 117 4.5.1

WET

WARP 54 54 4.5.1

FILLING 34 77 4.5.1

COLORFASTNESS TO:

PERSPIRATION (MIN.)

COLOR CHANGE 5 5 4.5.1

STAINING ON

COTTON 3.5 5 4.5.1

STAINING ON

WOOL 4.5 5 4.5.1

DRYCLEANING

COLOR CHANGE 4.5 5 4.5.1

STAINING ON

COTTON 4.5 5 4.5.1

STAINING ON

WOOL 4.5 5 4.5.1

CROCKING DRY 4.5 4.5 4.5.1

TABLE IV

TESTING REQUIREMENTS FOR ACETATE LINING CLOTH

COMPONENTS CHARACTER- REQUIREMENT TEST

. ISTIC PARAGRAPH METHOD

LINING CLOTH YARNS/INCH 3.3.2 ASTM D 3775

ACETATE

. WEIGHT 3.3.2 ASTM D 3776

. BREAK STRENGTH 3.3.2 ASTM D 5034

. COLORFASTNESS TO

. PERSPIRATION 3.3.2 AATCC 15

. DRYCLEANING 3.3.2 AATCC 132

. CROCKING 3.3.2 AATCC 8

PARAGRAPH 4.5.1.1 SAMPLING. UNLESS OTHERWISE SPECIFIED

IN SUBSIDIARY SPECIFICATIONS, SAMPLING SHALL

BE IN ACCORDANCE WITH THE FOLLOWING. THE LOT

SHALL BE UNACCEPTABLE IF ONE OR MORE SAMPLE

UNITS FAIL TO MEET ANY TEST REQUIREMENTS

SPECIFIED HEREIN.

LOT SIZE SAMPLE SIZE (SAMPLE UNIT)

800 OR LESS 2

801 THROUGH 22,000 3

22,001 AND OVER 5

THE UNIT FOR EXPRESSING LOT SIZE AND SAMPLE

UNIT FOR TESTING EACH COMPONENT SHALL BE IN

ACCORDANCE WITH THE APPLICABLE SUBSIDIARY

SPECIFICATION OR AS FOLLOWS:

COMPONENTS LOT SIZE SAMPLE UNIT

. EXPRESS AS FOR TESTING

LINING CLOTH

ACETATE YARDS 1/2 YARD

(Ref. 90271)

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN).

THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO

DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC)

MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF

MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER)

OF MIL-DTL-32075.

ADDITIONAL INFORMATION FOR V-B-871: NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFO FOR A-A-203: NO ADDITIONAL INFORMATION FOLLOWS.

(ref. T0811 - May 18, 2006)

ADDITIONAL INFORMATION FOR A-A-50067:

PAGE 1 PARA 2.2, LINE 5, AFTER " SECTION 16"

DELETE "THE CLOTH SHALL HAVE A MAXIMUM SHRINKAGE

RATE OF 2.0 IN THE WARP AND FILLING DIRECTION."

AND SUBSTITUTE " THE CLOTH SHALL HAVE A MAXIMUM

SHRINKAGE RATE OF 4.0 IN BOTH THE WARP AND

FILLING DIRECTIONS."

(Ref. T0402)

ADDITIONAL INFORMATION: INTERIM CHANGES TO A-A-50186:

PAGE 1:

PARAGRAPH 1.1 TYPES, NEXT TO TYPE V NON-WOVEN ADD

"(MEDIUM WEIGHT)", UNDER TYPE V ADD "TYPE VI

NON-WOVEN (LIGHT WEIGHT)".

PARAGRAPH 2.1, LINE 5. GENERAL.: DELETE

"SATURATION BONDED WITH ACRYLIC TYPE BINDER"

AND SUBSTITUTE "EITHER WET-LAID, SATURATION BONDED OR THERMAL BONDED".

PAGE 2:

TABLE 1. PHYSICAL REQUIREMENTS (WOVEN) UNDER TEST

METHOD COLUMN, LINE 3 DELETE "1600" AND SUBSTITUTE

"AATCC 20 3/".

TABLE I. PHYSICAL REQUIREMENTS (WOVEN) AT BOTTOM OF

PAGE UNDER FOOTNOTE 2/ ADD THE FOLLOWING: "3/ AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS

TEST METHOD."

PAGE 3, TABLE II, PHYSICAL REQUIREMENTS (NONWOVEN) UNDER

TYPE V, AND VI, ACROSS "CONSTRUCTION": DELETE "WET-LAID"

AND "WET-LAID OR SATURATE, THERMAL BONDED" AND SUBSTITUTE

"SEE 2.1" FOR BOTH TYPES.

TABLE II, UNDER TYPE VI: ADD UNDER EACH CHARACTERISTIC:

"1.5, 12, 8, 2.5, 2.5, WET-LAID OR SATURATE THERMAL BONDED" RESPECTIVELY.

PAGE 3, PARAGRAPH 3.2 FINISH. LINE 1 DELETE "AN APPROVED" AND SUBSTITUTE " A COMMERCIALLY

ACCEPTED".

PAGE 5: ADD THE FOLLOWING: "5.7 SUPER SESSION DATA.

THE TYPES OF CLOTH COVERED BY THIS COMMERCIAL ITEM

DESCRIPTION REPLACE TYPES COVERED BY CCC-C-438 AS FOLLOWS:

A-A-50186 CCC-C-438

TYPE I TYPE I, CLASSES 1 AND 2

TYPE II TYPE II, CLASS 1

TYPE III TYPE III, CLASS 1

TYPE IV TYPE III, CLASS 2

TYPE V TYPE IV, CLASS 1

TYPE VI TYPE IV, CLASS 2"

(ref. T1034 - May 19, 2006)

ADDITIONAL INFORMATION FOR A-A-50196:

(NO CURRENT CHANGES TO A-A-50196B)

ADDITIONAL INFORMATION FOR A-A-50198A:

THREAD, GIMP SHALL BE IN ACCORDANCE WITH

A-A-50198, JUNE 30, 1989.

ADDITIONAL INFORMATION FOR A-A-50199

NO ADDITIONAL INFORMATION

ADDITIONAL INFORMATION FOR A-A-52094A THREAD, COTTON

NO ADDITIONAL INFORMATION

(ref. T1481)

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD SAMPLE FOR SHADE. CLASS 5

FABRIC IS MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

CHANGES TO V-T-295E:

THREAD, NYLON; V-T-295 DATED AUGUST 1, 1985 IS HEREBY CANCELLED; FUTURE ACQUISITONS SHOULD

REFER TO THREAD, NYLON, A-A-59826 DATED 03 MARCH 2009 AS A REPLACEMENT.

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARAGRAPH 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE

"MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR DDD-T-86H:

NOTICE 1, DATED 5/4/1995, DDD-T-86H IS

CANCELLED; FUTURE REFER TO A-A-52071.

ADDITIONAL INFORMATION FOR DDD-T-86:

INTERIM CHANGES TO DDD-T-86H:

NOTE - REDUCED AQLS APPLY AS FOLLOWS:

PAGE 9, LINE 9, DELETE "0.4" AND SUBSTITUTE,

"0.28", FOR MAJORS. DELETE "1.5" AND SUBSTITUTE

"1.0", FOR TOTALS.

COMMERCIAL ITEM DESCRIPTION A-A-52071

DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR

USE IN PLACE 0F DDD-T-86H.

"THE REQUIREMENT FOR THE HERRINGBONE TAPE IS TYPE I, 3/16 INCH WIDTH AND 58 PICKS PER INCH

FROM TABLE I. PHYSICAL REQUIREMENTS."

A-A-52105 CLOTH, INTERLINING, COTTON OR

. STNTHETIC WARP, AND SPUN HAIR-

. WOOL OR RAYON FILLING, 5/7/91

(SEE PGC 93380)

INTERIM SPECIFICATION CHANGES TO

A-A-52105:

PAGE 1,PARAGRAPH 2.1,GENERAL DESCRIPTION.,

LINE 2: DELETE: "100 % POLYESTER".

LINE 5, DELETE "BLEND OF GOAT-HAIR" AND

SUBSTITUTE "BLEND OF HORSEHAIR OR GOAT-HAIR".

PAGE 2, PARAGRAPH 2.1, LINE 6, AFTER _YARN_:

DELETE THE PERIOD AND ADD *OR A 100% POLY-

ESTER STAPLE FIBER SPUN SINGLES YARN.".

PAGE 2, PARAGRAPH 2.2, TABLE 1, UNDER

"CHARACTERISTIC" COLUMN, UNDER "ANIMAL FIBER

CONTENT PERCENT: 2/", DELETE "GOAT-HAIR AND

RAYON FILLING" AND SUBSTITUTE "HORSE OR GOAT-

HAIR AND RAYON".

PAGE 2, PARAGRAPH 2.2, TABLE 1, UNDER

"CHARACTERISTIC" COLUMN, UNDER "WEIGHT, OZ./SQ.

YD.","MINIMUM", UNDER"TYPE 11" COLUMN, DELETE

"7.0" AND SUBSTITUTE "6.8".

PAGE 2, PARAGRAPH 2.2, TABLE 1, UNDER

"CHARACTERISTIC" COLUMN, UNDER "WEIGHT,OZ./SQ.

YD.","MAXIMUM", UNDER "TYPE 1" COLUMN, DELETE

"7.0"AND SUBSTITUTE "6.7".

PAGE 2,PARAGRAPH 2.2, TABLE 1, UNDER

"CHARACTERISTIC" COLUMN, UNDER "YARNS PER INCH

(MIN).", "FILLING", UNDER "TYPE 11" COLUMN.

DELETE "34" AND SUBSTITUTE "27".

PAGE 3, PARAGRAPH 2.2, TABLE 1, UNDER

"CHARACTERISTIC" COLUMN,"BREAKING STRENGTH,LBS.

(MIN).","WARP", UNDER "TYPE 11" COLUMN, DELETE

"50" AND SUBSTITUTE "35".

PAGE 3, PARAGRAPH 2.2, TABLE 1, FOOTNOTE 4/,

AFTER "DIRECTION." INSERT "STIFFNESS VALUES

SHALL BE MAINTAINED AFTER ONE COMMERCIAL

DRYCLEANING USING PERCHLOROETHYLENE SOLVENT

(SAME AS DRESS COAT)."

PAGE 2, TABLE 1, PHYSICAL REQUIREMENTS UNDER

TEST METHOD COLUMN, LINE 2 DELETE "1600" AND

SUBSTITUTE "AATCC 20 6/".

PAGE 3, BELOW FOOTNOTE "5/" ADD "6/ AATCC TEST

METHOD."

PAGE 5, ADD THE FOLLOWING NEW PARAGRAPH:

"5.2.1.2 NON-GOVERNMENT PUBLICATIONS. THE

FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT

TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE

SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE

DOD ADOPTED ARE THOSE LISTED IN THE ISSUE OF THE

DODISS CITED IN THE SOLICITATION. UNLESS

OTHERWISE SPECIFIED, THE ISSUES OF DOCUMENTS

NOT LISTED IN THE DODISS ARE THE ISSUES OF THE

DOCUMENTS CITED IN THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC)

AATCC 20 - FIBER ANALYSIS: QUALITATIVE

(APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE

PARK, NC 27709-2215)"

ADDITIONAL INFORMATION FOR MIL-C-297:

NOTE: COMMERCIAL ITEM DESCRIPTION A-A-52105

IS AUTHORIZED IN PREFERENCE TO MIL-C-297

INTERIM CHANGES TO MIL-C-297G:

PAGE 2, ADD THE FOLLOWING NEW PARAGRAPH:

"2.1.3 OTHER PUBLICATIONS. THE FOLLOWING

DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE

EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPEC-

IFIED THE ISSUES OF THE DOCUMENTS WHICH ARE DOD

ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF

THE DODISS SPECIFIED IN THE SOLICITATION. UNLESS

OTHERWISE SPECIFIED, THE ISSUES OF DOCUMENTS NOT

LISTED IN THE DODISS SHALL BE THE ISSUES OF THE

NON GOVERNMENT DOCUMENTS WHICH ARE CURRENT ON

THE DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMIST AND

COLORISTS (AATCC)

AATCC 20 - FIBER ANALYSIS: QUALITATIVE

PAGE 8, TABLE III, UNDER TEST METHOD COLUMN,

LINE 2, DELETE "1600" AND SUBSTITUTE "AATCC 20".

(Ref. T0897)

ADDITIONAL INFORMATION FOR MIL-B-371:

PAGE 2, AT THE TOP OF THE PAGE AFTER "CLASS 3" ADD "AND 4". DELETE "CLASS 4 -WATER AND

MILDEW-RESISTANT FINISH 2, 2' METHYLENE BIS (4-CHLOROPHENOL)".

PAGE 3, PARAGRAPH 2.2 OTHER PUBLICATIONS. ADD THE FOLLOWING BELOW "APPLICATION FOR COPIES SHOULD BE ADDRESSED TO: ASTM INTERNATIONAL, 100 BARR HARBOR DRIVE, WEST CONSHOHOCKEN, PA.

19428"

"AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS:

QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO: AMERICAN ASSOCIATION OF TEXTILE

CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 4, PARAGRAPH 3.3.3, DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING: "3.3.3 POLYPROPYLENE YARN (AS AN ALTERNATIVE FOR TYPES III AND VII BRAID). THE YARN SHALL BE TEXTURED POLYPROPYLENE OF SUITABLE DENIER TO MEET THE REQUIREMENTS OF THIS DOCUMENT.

POLYPROPYLENE BRAID IS APPLICABLE ONLY TO THE ITEMS LISTED IN PARAGRAPH 6.7."

AFTER PARAGRAPH 3.3.4: ADD THE FOLLOWING NEW PARA: "3.3.5. 100% TEXTURED POLYESTER(AS AN ALTERNATIVE FOR TYPES I, II, IV, AND VI).THE YARN SHALL BE TEXTURED POLYESTER OF A SUITABLE

DENIER TO MEET THE REQUIREMENTS OF THIS DOCUMENT."

PAGE 5, PARAGRAPH 3.5.3 AFTER "CLASS 3" ADD "CLASS 4." AFTER "THE CLASS 3" ADD "AND 4".

PARAGRAPH 3.5.4, DELETE IN ITS ENTIRETY.

PAGE 8, ADD THE FOLLOWING TABLE IIA:

"TABLE IIA PHYSICAL REQUIREMENTS FOR POLYESTER BRAID

TYPE DIAMETER WEIGHT PER NUMBER OF ENDS PER

(INCHES) 144 YARDS CARRIERS CARRIER

(OUNCES)

MIN.

II 5/32+/-1/32 28.0 8 1

VII 11/32+/-1/32 25.0 44 1

NUMBER YARN PLY PICKS BREAKING

OF ENDS BRAID CORE PER INCH STRENGTH

IN CORE MIN. (LBS.) MIN.

1/ 8 2 3 10 140

- - - 22 200

1/ UNDYED COTTON CORE YARNS."

PAGE 10, PARAGRAPH 4.4.2.1 YARD-BY-YARD EXAMINATION, LINE 9, DELETE "1.5" AND SUBSTITUTE "1.0"

PAGE 13, TABLE V. END ITEM TESTS UNDER REFERENCED TEST METHOD COLUMN, LINES 4 AND 5 DELETE

"1600" AND SUBSTITUTE "AATCC 20"

(ref. T0821 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-DTL-10176:

INTERIM SPECIFICATION CHANGES TO MIL-DTL-10176K:

3.7.3, LINE 2: DELETE "5.5" AND SUBSTITUTE "5.0"

ADD THE FOLLOWING PARAGRAPHS:

"3.7.4 WATER REPELLENT TREATMENT. WHEN SPECIFIED

, THE CLOTH SHALL BE GIVEN AN APPROVED DURABLE

FLUOROCHEMICAL TYPE WATER REPELLENT TREATMENT

AND SHALL CONFORM TO THE REQUIREMENTS

SPECIFIED IN 3.7.2 WHEN TESTED AS SPECIFIED IN

4.4.4.

3.7.4.1 SPRAY RATING. THE RESULTS OF THE THREE

INDIVIDUAL DETERMINATIONS ON THE SAMPLE UNIT FOR

SPRAY RATING SHALL BE EQUAL TO OR BETTER THAN

RATINGS OF 90,90,80 INITIALLY AND 80,80,70 AFTER

ONE DRYCLEANING WHEN TESTED AS SPECIFIED IN

4.4.4."

PAGE 9, PARAGRAPH 4.3.3.1 YARD-BY-YARD

EXAMINATION, LINE 3, DELETE "10" AND SUBSTITUTE

"7", LINE 4, DELETE "12" AND SUBSTITUTE "8"

TABLE II, BELOW "PH": ADD THE FOLLOWING UNDER

THEIR RESPECTIVE COLUMNS:

"WATER REPELLENCY:

SPRAY RATING:

INITIAL--------3.7.3.1---------5526

AFTER 1 DRYCLEANING----3.7.3.1---5508 AND 5526

SPONGING:

COLD WATER SPONGING IS REQUIRED. A PROPER

ALCOHOL WETTING AGENT SHALL BE USED TO INSURE

SHRINKAGE IS ACCOMPLISHED AND WATER RESISTANT

FINISH IS NOT RELEASED.

THE WATER REPELLANT TREATMENT MUST BE

APPLIED BEFORE THE SPONGING OPERATION.

ALL THE SPECIFICATION REQUIREMENTS MUST BE MET.

CODE OF FEDERAL REGULATIONS

16 CFR PART 1500- FEDERAL HAZARDOUS SUBSTANCES

ACT REGULATIONS.

29 CFR PART 1910- OCCUPATIONAL SAFETY AND HEALTH

STANDARDS.

(APPLICATIONS FOR COPIES OF REFERENCED

DOCUMENTS SHOULD BE ADDRESSED TO U.S

GOVERNMENT PRINTING OFFICE, SUPERINTENT OF

DOCUMENTS, MAIL STOP: SSOP, WASHINGTON, DC

20402-9328.)

PRINCIPLES AND METHODS OF TOXICOLOGY,

A. WALLACE HAYES (EDITOR), 1989, PP 394-396.

(APPLICATIONS FOR COPIES OF REFERENCED

DOCUMENTS SHOULD BE ADDRESSED TO RAVEN

PRESS,1185 AVENUE OF THE AMERICAS, NEW YORK,

NY 10036.)

TOXICITY. THE FINISHED CLOTH SHALL NOT

PRESENT A DERMAL HEALTH HAZARD WHEN USED

AS INTENDED.

TOXICITY ASSESSMENT. THE CONTRACTOR MUST

FURNISH INFORMATION WHICH CERTIFIES THAT

THE FINISHED PRODUCT IS COMPOSED OF MATERIALS

WHICH HAVE BEEN SAFELY USED COMMERCIALLY OR

PROVIDE SUFFICIENT TOXICITY DATA TO SHOW

COMPATIBILITY WITH PROLONGED, DIRECT SKIN

CONTACT. AT A MINIMUM, TOXICITY DATA SHOULD

INCLUDE RESULTS FROM A PRIMARY DERMAL IRRITATION

STUDY IN LABORATORY ANIMALS AND A REPEATED

INSULT HUMAN PATCH TEST (MODIFIED DRAIZE

PROCEDURE). THE LATTER MUST BE CONDUCTED UNDER

THE SUPERVISION OF A QUALIFIED DERMATOLOGIST

USING AT LEAST 100 FREE LIVING INDIVIDUALS.

(REF. T0969)

ADDITIONAL INFORMATION FOR MIL-P-15064:

INTERIM CHANGE TO MIL-P-15064G:

AS AN ALTERNATE PADS, SHOULDER AND SLEEVE-HEAD

ADD "BLEACHED MUSLINETTE".

PAGE 4, PARAGRAPH 3.2.1 PRINT CLOTH. ADD THE

FOLLOWING SENTENCE AT THE END OF THE PARAGRAPH

"AS AN ALTERNATE, THE TYPE IV SLEEVE-HEAD OUTER

COVER SHALL BE 100% COTTON MUSLIN WITH A MINUMUM

OF 44 WARP AND 36 FILLING YARNS PER SQUARE INCH.

TABLE I. MATERIAL REQUIREMENTS, ADD THE FOLLOW-

ING INFORMATION TO THE TABLE.

TYPE IV 44 BY 36"

PAGE 4: PARAGRAPH 3.2.2.1, LINE 2, AFTER "CLASS 1":

ADD "OR CLASS 2".

PAGE 4: PARAGRAPH 3.2.2.2,LINE 2, AFTER "UNBLEACHED"

ADD "OR BLEACHED".

PAGE 6, PARAGRAPH 3.2.6 WADDING. ADD THE FOLL-

ING SENTENCE AT THE END OF THE PARAGRAPH. "AS AN

ALTERNATE, THE TYPE IV SLEEVE-HEAD FILLER SHALL

BE 100% PRENEEDLED COTTON FILLER, WEIGHING A

MINIMUM OF 3.0 OUNCES PER SQUARE YARD AND A MAX-

IMUM OF 3.5 OUNCES PER SQUARE YARD"

PAGE 8, ADD "PARAGRAPH 3.5.10 TYPE IV. AS AN

ALTERNATE TYPE IV SLEEVE-HEAD SHALL MEASURE 15

INCHES (+/- 1/4 INCH) FOR MEN AND 13 INCHES (+/-1/4

INCH) FOR WOMEN."

PAGE 9, ADD THE FOLLOWING INFORMATION TO TABLE

II.

TABLE II. MANUFACTURING OPERATIONS REQUIREMENTS-

CONTINUED.

NO. REQUIRMENTS STITCH SEAM STITCHES THREAD

. TYPE TYPE PER INCH NDL BOB

1. CUTTING: "OR

C. THE MUSLIN SHALL BE SPLIT 3 INCHES (+/-1/8

INCH) IN THE BIAS DIRECTION."

2.CONSTRUCTION: "OR C. FOLD THE MUSLIN BIAS

STRIP TO FINISH TWO INCHES +/- 1/8 INCH. THE

COTTON FILLER WILL BE INSIDE THE FOLDED MUSLIN.

THE COTTON WILL BE CUT 2 -1/4 INCHES +/-1/8 INCH

WIDE. BOTH PIECES WILL BE SEWN WITH A STITCH

LINE APPROXIMATELY 1/2 INCH FROM THE FOLDED EDGE

OF THE SLEEVE HEAD. (SEE FIGURE 6, PAGE 37)"

301/401 EFA-1 3-4 70-2 70-2

PAGE 37, ADD FIGURE 6, SLEEVE HEAD, MAN'S AND

WOMEN'S TYPE IV."

ALTERNATE WOMEN'S PAD'S INSERT "B" REQUIREMENTS

THE SHOULDER PADS SHALL HAVE A TOP AND BOTTOM

COVER OF 4 OUNCES PER SQUARE YARD WHITE NEEDLE

PUNCHED POLYESTER FELT WHEN TESTED IN ACCORDANCE

WITH ASTM D-3776, OPTION C. THE FILLER SHALL BE

COTTON, ONE PIECE SHAPED TO FILL OUT THE PAD

WITH AN EVEN SMOOTH TAPER FROM CENTER TO ALL

EDGES. MULTIPLE PIECES ARE NOT ACCEPTABLE. THE

TOP COVER SHALL BE NOTCHED FOR SHOULDER SEAM

ALIGNMENT 4-3/4 INCHES FROM THE FRONT OF THE PAD

THE PAD SHALL BE SEWN IN A CONCAVE SHOULDER FIT-

TING FORM UTILIZING MULTI-LINE OF BASTING, TOTAL

ING 6 ROWS. THE PAD SHALL HAVE A COMPRESSED FIN-

ISHED THICKNESS MEASURING 3/8 +/- 1/8 INCH USING

A ONE INCH FOOT AT 0.1 PSI. THE FINISHED PAD

SHALL MEASURE 8-1/2 TO 9-1/2 INCHES IN LENGTH

AND 4-1/2 TO 5 INCHES IN WIDTH, WITH A 1/2 INCH

ARMHOLE CUTOUT ON EACH SIDE. THE PADS SHALL NOT

BE SIGNIFICANTLY ALTERED IN THICKNESS, SHAPE OR

DIMENSION AFTER BEING COMMERICALLY DRY CLEANED 3

TIMES WITH PERCHLOROETHELENE. THE PAD SHALL HAVE

A MINIMUM BREAKING STRENGTH OF 6.0 POUNDS IN THE

MACHINE DIRECTION AND A MINIMUM OF 3.0 POUNDS IN

IN THE CROSS DIRECTION WHEN TESTED IN ACCORDANCE

ASTM-D 5034, OPTION G-T OR G-E.

ALTERNATE MEN'S PAD'S INSERT "A" REQUIREMENTS

THE SHOULDER PADS SHALL HAVE A TOP AND BOTTOM

COVER OF 4 OUNCES PER SQUARE YARD WHITE NEEDLE

PUNCHED POLYESTER FELT WHEN TESTED IN ACCORDANCE

WITH ASTM D 3776, OPTON C. THE FILLER SHALL BE

COTTON, ONE PIECE SHAPED TO FILL OUT THE PAD

WITH AN EVEN SMOOTH TAPER FROM CENTER TO ALL

EDGES. MULTIPLE PIECES ARE NOT ACCEPTABLE. THE

TOP COVER SHALL BE NOTCHED FOR SHOULDER SEAM

ALIGNMENT 4-1/4 INCHES FROM THE FRONT OF THE PAD

THE PAD SHALL BE SEWN IN A CONCAVE SHOULDER FIT-

TING FORM UTILIZING MULTI-LINE OF BASTING, TOTAL

ING 6 ROWS. THE PAD SHALL HAVE A COMPRESSED FIN-

ISHED THICKNESS MEASURING 1/2 +/- 1/8 INCH USING

A ONE INCH FOOT AT 0.1 PSI. THE FINISHED PAD

SHALL MEASURE 9-3/4 TO 10/3/4 INCHES IN LENGTH

AND 5-3/8 TO 5-5/5 INCH IN WIDTH, WITH A 1/2 INCH

ARMHOLE CUTOUT ON EACH SIDE. THE PADS SHALL NOT

BE SIGNIFICATNLY ALTERED IN THICKNESS, SHADE OR

DIMENSION AFTER BEING COMMERCIALLY DRY CLEANED 3

TIMES WITH PERCHLOROETHELENE. THE PAD SHALL HAVE

A MINIMUM BREAKING STRENGTH OF 6.0 POUNDS IN THE

MACHINE DIRECTION AND MINIMUM OF 3.0 POUNDS IN

THE CROSS DIRECTION WHEN TESTED IN ACCORDANCE

WITH ASTM-D 5034, OPTION G-T OR G-E.

DEVIATION FROM MIL-P-15064F;

. PAGE 6, PARAGRAPH 3.5.1, LINE 4

. DELETE "7/8+1/8 INCH" AND

. SUBSTITUTE "1/2+1/8 INCH."

(Ref. T1553)

ADDTIONAL INFORMATION FOR MIL-C-15065

INTERIM CHANGES TO MIL-C-15065

PAGE 5, PARAGRAPH 3.3.2

LINE 6, AFTER "TYPES" ADD "IV"

LINE 7, AFTER "HAVING": ADD "SINGLE"

LINE 7, DELETE *FROM 100% POLYESTER).

LINE 10, AFTER "NYLON" AND MONO-FILAMENT

INSERT "OR POLYESTER".

LINE 11, DELETE "42" AND SUBSTITUTE "41"

LINE 12, DELETE "5.6" OUNCES" AND SUBSTITUTE

"5.4 OUNCES"

LINE 13, DELETE "0.060" AND SUBSTITUTE "0.055"

FOR MEN'S COAT FRONT, TYPE XI

COAT, MANS, DRESS BLUE MC, MIL-C-19156G

PATTERN DATE, DELETE COAT FRONT 31 MAY 1988

ADD; COAT FRONTS 29 OCT 1999

INTERIM CHANGES TO MIL-C-15065J:

PAGE 8, TABLE II, LIST OF PATTERN PARTS, TYPE IX

AND X, DELETE ENTIRELY AND SUBSTITUTE:

"BASIC MATERIAL FRONT 2

. CHEST PIECE 2

. WEDGE PIECE (SHOULDER) 4

HAIRCLOTH SHOULDER PIECE 2

FELT OR FLANNEL CHESTPADDING 2"

DELETE FIGURE 7 AND SUBSTITUTE NEW FIGURE 7

ATTACHED.

Page 7.Delete "PARAGRAPH 3.4" and substitute "Page 6, Para 3.34".

Line 2, after "or flannel" add "or needle punched polyester" Line 4, after "felt" add "or needle punched polyester" After PARAGRAPH 3.3.4.2, add the following new paragraph:

"3.3.4.3 Polyester. The polyester shall be unbleached, needle punched non-woven material.

The weight of the material shall be 3.4 (max), oz./sq. yd. The initial thickness shall be

0.055 inch and thickness after three commercial perchloethylene dry cleanings and pressings shall be 0.65 inch (max.), when tested using a 1-/8 diameter foot gage at 0.1 psi. The breaking strength in the machine direction shall be 20 lb. (min.) and in the cross machine direction shall be 40 lb. (min.) when tested as specified in ASTM D 5034. The polyester material shall not shrink or elongate more than 4.0 percent (max.) in the machine direction and 2.5 percent (max.) in the cross-machine direction after three commercial dry cleanings, when tested as specified in 4.4.1.2 (see 6.7)".

Page 10, Table II, under "Component" for "Type XVIII", after "Felt or flannel", add "or needle punched polyester" Page 11, Table II, under "Component" for "Type XXV", after "Felt", add "or needle punched polyester" Page 15, Table III, Operation 1.e., Line 1, after "or flannel" add "or needle punched polyester" Page 15, Table III, Operation 1.e.(1), Line 1, after "felt" add "or needle punched polyester" Page 15, Table III, Operation 1.e(1), for Type XVIII, line 1, after "felt" add "or needle punched polyester" Page 34, Table III, Operation 21.c., Line 1, after "felt" add "or needle punched polyester" Page 36, add the following new paragraphs:

4.4.1.2.1 Preparation of specimens. Three (3) 22 inch by 22 inch square specimens shall be cut parallel to the machine and cross machine directions to within 3 inches of the selvage from the polyester sample. An 18 inch square shall be marked as a minimum at each corner within the 22 inch specimen with indelible ink. No marks shall be closer to the edge of the specimen than 1 inch. The specimen shall be commercially dry cleaned three times using perchoethylene solvent. Samples shall be bottom steam pressed after each dry cleaning for twenty seconds in a non-locked position and vacuumed for 10 seconds.

4.4.1.2.2 Dimensional stability calculation. Each of the three 22 inches by 22 inches specimens shall be laid out without tension on a flat surface. Care should be taken that the specimens are free from wrinkles and creases. The previously measured distances marked on the specimens (initial measurement, 18 inches) in the warp direction shall be re-measured to the nearest 1/16 inch, recorded, averaged and calculated for dimensional change. The dimensional change of the sample unit (3 specimens) shall be calculated to the nearest 0.10 percent using the following formula:

Dimensional change, percent = (A-B)/A x 100

Where A = Average of initial measurements (18 inches) B = Average measurements after dry cleaning Page 44, Table V, under "Examine: for "Type XXV fronts", line 2, delete "Shoulder piece felt:" and substitute "Shoulder piece".

Page 48, add the following new paragraph:

6.7 Polyester material. A suggested style and source for the specified material is Style CTF006-3, Product No. F012772 available from National Nonwovens, P.O. Box 150, Easthampton, MA 01027, Telephone (413) 527-3445

The following changes to MIL-C-15065 have been approved by the Army and Air Force as of June 2009:

Page 5, Paragraph 3.3.2: Delete paragraph in its entirety and substitute: "3.3.2 Haircloth.

The material for the shoulder pieces (types IV, VI, VII, XIV, XVII, XVIII and XXII), chest pieces and reinforcement piece for top front corners (type XI) shall be a plain weave construction with 100% spun polyester warp yarns with 100% monofilament polyester filling yarns and shall conform to the requirements in Table A (see 6.7). The material shall be undyed and contain no sizing (see 4.4.1.1) or resins.

Table A. Material requirements

Characteristic Requirement Test Method

Weight, oz/sq yd., min 5.2 ASTM D 3776

Yarns per inch, min:

Warp 52 ASTM D 3775 Filling 31 ASTM D 3775

Breaking strength, min:

Warp 160 ASTM D 5034 Filling 250 ASTM D 5034

Dry cleaning shrinkage (%), max., after 3 dry cleanings:

Warp 2.0% Commercial dry cleaning 1/ 2/ Filling 2.0% Commercial dry cleaning 1/ 2/

Stiffness, filling, load lbs., min Initial 0.120 ASTM D 747 1/ 2/ After 3 dry cleanings 0.115 ASTM D 747 1/ 2/

1/ Material shall be steam pressed between each dry cleaning.

2/ Each individual Service reserves the right to test for appearance, shrinkage, and stiffness in an end item configuration."

Page 48, Add the following new paragraph:

"6.7 Suggested Source, A suggested source for the haircloth is QST Industries, Inc., 525 West Monroe Street, Suite 1400, Chicago, IL 60661, Telephone Number (312) 930-9400.

QST Part # BR-CHESTPC-50-WE has been found to meet these requirements."

ADDITIONAL INFORMATION FOR MIL-B-17757:

MIL-B-17757 IS CANCELLED WITHOUT REPLACEMENT.

THE FOLLOWING DOCUMENTS ARE AUTHORIZED FOR USE IN LIEU

OF MIL-B-17757:

ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD SHIPPING

CONTAINERS.

(ref. T0857 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-B-20289:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T0863)

ADDITIONAL INFORMATION FOR MIL-C-29137:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T1562)

ADDITIONAL INFORMATION FOR MIL-C-44192:

INTERIM CHANGES TO MIL-C-44192:

PAGE 4, PARA 3.2.4 AFTER "II" ADD "FOR DRESS

COATS AND TYPE "III" FOR ALL WEATHER COATS."

PAGE 11, PARA 30.4, DELETE AND SUBSTITUTE:

"30.4 CONTAINER CLOSURE. THE CONTAINER SHALL BE

CLOSED BY THE USE OF 3 INCH WIDE TAPE CONFORMING

TO TYPE II, CLASS 2 OF PPP-T-45. THE TAPE SHALL

BE CENTERED OVER EACH EXPOSED SEAM INCLUDING

THE DISPENSING DOOR SLITS AND EXTENDED OVER ALL

THE CORNERS AND EDGES WITH A MINIMUM OF 2 INCHES

ONTO THE ADJACENT BOX PANELS. THE MANUFACTURERS

JOINT AND THE EDGES AROUND THE BOTTOM OPENING

OF THE LID AFTER IT IS PLACED OVER THE

CONTAINER BOX BODY NEED NOT BE TAPED.".

NOTE: WHEN HANGER PACKS ARE SPECIFIED FOR ALL-

WEATHER COATS, COATS SHALL BE PACKAGED, MARKED

AND PALLETIZED IN ACCORDANCE WITH MIL-C-44192,

WITH FRONTS LAPPING AND BUTTONED.

THE FOLLOWING APPLIES:

TEN (10) COATS OF ONE CLASS AND SIZE SHALL BE

PACKED IN A TYPE I CONTAINER (HANGER PACK)

EXCEPT THAT THE DIMENSIONS OF THE CONTAINER

SHALL APPROXIMATE 24 X 21 INCHES AND THE DEPTH

OF THE CONTAINER SHALL BE 48 +0/-2 INCHES.

HANGER PACK SHIPPING CONTAINERS SHALL BE

MARKED A/C TO IDENTIFY THE LEVELS OF PACKAGING/

PACKING.

(Ref. T0806)

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1" INSERT

"TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X - CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT LISTED IN THE DODISS SHALL BE THE ISSUES OF THE

NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO AMERICAN ASSOCIATION OF TEXTILE

CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR KNIT.

WHEN SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1. TYPE X1 SHALL BE STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF CHAINSTITCHING IS SEWN IN THE MACHINE

DIRECTION OF THE SUBSTRATE IN ORDER TO REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING CHAINSTITCH STITCH

TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS FUSIBLE SEAM

TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARAGRAPH 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24, DELETE "45" AND

SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND 3 DELETE "1600" AND

SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER LAUNDERING/DRY CLEANING). DELETE THE FIRST AND SECOND SENTENCES IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED

FOR CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL PART FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL

STABILITY AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE FOLLOWING BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES, OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED TO DETERMINE IF DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-STD-1608:

INTERIM CHANGES TO MIL-STD-1608C:

PAGE 14, BEFORE "COAT BUTTONED ON FORM" ADD "B."

PAGE 17: DEFECT E.4., LINE 1, AFTER "TO" ADD

"ROLL OUTWARD AND NOT".

PAGE 19: TABLE II, AFTER DEFECT XXI SLEEVE PARAGRAPH

E. ADD "NOTE: THE NORMAL HANGING POSITION FOR

THE FRONT EDGE OF THE SLEEVE IS THE CENTER OF

THE TOP EDGE OF THE LOWER PATCH POCKET."

PAGE 22: BEFORE "XXIX", ADD "C. COAT SPREAD OUT

ON TABLE"

PAGE II, ADD NEW DOCUMENT "MIL-C-29628 (NU)

COAT, WOMEN'S, BLUE DRESS".

MIL-STD-1608C PAGE 7, TABLE I DELETE IN ITS

ENTIRETY AND SUBSTITUTE "TABLE I SAMPLING

PROVISIONS".

NORMAL INSPECTION

LOT SZ SAMP SZ MAX ACCP MAX ACCP PT VALU

. NO. FOR

. SELECTED 3&2 PT 3,2,1 PT

. (*DEFECT) DEFECTS DEFECTS

UP THRU 90 20 0 3 7

91- 150 32 0 4 11 151-280 50 0 7 13 281-500 80 0 9 19 501-1200 125 1 14 27 1201-3200 200 1 18 36 3201-10,000 315 2 25 55 10,001-35,000 500 3 36 81

35,001 & OVER 800 5 55 122

TIGHTENED INSPECTION

UP THRU 90 20 0 3 5

91-150 32 0 3 7 151-280 50 0 5 11 281-500 80 0 7 14 501-1200 125 1 11 21 1201-3200 200 1 13 31 3201-10,000 315 2 22 47 10,001-35,000 500 3 33 69

35,001 & OVER 800 5 49 104

REDUCED INSPECTION

UP THRU 280 20 0 2-4 7

281-500 32 0 3-7 12 501-1200 50 0 6-10 15 1201-3200 80 0 7-10 24 3201-10,000 125 1 13-18 31 10,001-35,000 200 1 17-23 47

35,001 & OVER 315 2 23-29 69

NOTE: FOR THE REDUCED POINT VALUES OF THE

REDUCED INSPECTION ON 3 & 2 POINT DEFECTS. IF

THE FIRST VALUE IS EXCEEDED, BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

(Ref. T0344)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2

22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2