Army Coat Womens Blue pgc03434v4.pdf

Coat, Woman's, Polyester/Wool, Army Blue 450, shall be made in accordance with GL/PD 07-07C dated 4 March 2009

Pattern Date: June 30, 2008.

Standard sample of cloth polyester/wool,9.5- 10.5 oz/ linear yd, MIL-DTL-823, Type III, class 4, Army blue shade 450 is available and applicable for shade only under piece no. Roll 3801.

Interim specification changes to GL/PD 07-07C:

PAGE 1, PARAGRAPH 1.2 CLASSIFICATION DELETE “CLASS 3- WOOL, ELASTIQUE, ARMY BLUE 150 AT THE BOTTOM OF PAGE ADD, DISTRIBUTION STATEMENT A. Approved for public release, distribution unlimited.

PAGE 3, PARAGRAPH. 2.2.1,

UNDER SPECIFICATIONS, FEDERAL

DELETE V-T-295 AND SUBSTITUTE A-A-59826 – Thread, Nylon

UNDER DESCRIPTIONS, COMMERCIAL ITEM

DELETE A-A- 50196- Thread, Silk

UNDER SPECIFICATIONS, DEPARTMENT OF DEFENSE

DELETE MIL-C-3738, Cloth, Elastique, Wool

UNDER STANDARDS, MILITARY

REINSTATE MIL-STD-147, PALLETIZED UNIT LOADS.

AFTER “ON-LINE AT” DELETE http://assist.daps.dla.mil/quicksearch AND SUBSTITUTE http://quicksearch.dla.mil.

PAGE 4, PARAGRAPH. 2.2,2 AFTER paragraph “FEDERAL ACQUISITION REGULATIONS (FAR)” ADD the following:

FEDERAL TRADE COMMISSION (FTC)

Rules and Regulations Under the Textile Fiber Products Identification Act (Copies of this document are available online at http://www.ftc.gov.)

PARAGRAPH. 2.3 NON-GOVERNMENT PUBLICATIONS

UNDER AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC)

DELETE AATCC Test Method 16 - Colorfastness to Light: Drycleaning AND SUBSTITUTE AATCC Test Method 16.3 - Colorfastness to Light: Xenon

UNDER ASTM INTERNATIONAL INSERT THE FOLLOWING TEST METHOD AT THE END OF THE LIST

ASTM D6199 WOOD MEMBERS OF CONTAINERS AND PALLETS

Page 6, DELETE paragraph 3.4.1.3 Class 3 (MDW) in its entirety.

Page 6, Paragraph 3.4.4.1, after "shoulder loops", insert "a 1 inch wide bias cut fusible strip" and at the end of the paragraph: Add the following:

"As an alternate, the complete front facing can be fused."

PARAGRAPH 3.4.7.7.2, Thread, Silk DELETE in its entirety and all references thereafter.

PARAGRAPH 3.4.7.7.3, LINE 1 DELETE “as an alternate to the silk thread as specified in 3.4.7.7.2”

LINE 4, DELETE "V-T-295" SUBSTITUTE "A-A-59826"

http://assist.daps.dla.mil/quicksearch http://quicksearch.dla.mil/

Page 10, paragraph 3.4.7.7.5, DELETE ”polyester-core silk or”.

Page 10, paragraph 3.4.8, at the end of the paragraph add "Each coat shall contain a DSCP Exclusive Woven Label" Page 10, paragraph.8.1, line 2, after "Type VI": Add "Class 15." Line 4: Delete "Style #4800WT or Style 4822WT" and substitute "Style #4800TWT or Style #4800HWT".

Page 11, paragraph 3.4.8.2, line 5, after "MIL-STD-984.": Add "as an alternate to the material specified in MIL-DTL-32075, the label material may be a 100% polyester coated tape conforming to Avery Dennison's Style #4800TWT or Style #4800HWT (see 6.11). The labels shall show colorfastness to drycleaning equal to or better that "3-4" according to AATCC Evaluation Procedure 1 and AATCC Evaluation Procedure 2 when tested as specified in 4.3.1."

Page 13, paragraph 3.4.8.2: Delete Table for "HEIGHT RANGES" and substitute the new table"

"Less than 63-1/2 inches 63-1/2 to 67 inches 67 to 71 inches over 71 inches Petite Regular Tall X-Tall"

Page 22, Table II, operation 4b: after step 6, insert the following new operation:

"(7). Center back neckline: Fuse a 1 inch wide bias cut small parts fusible strip to each center back neckline".

Page 33 Table II, operation 14: Add the following new operation at the end:

"d. Blind stitch bridle tape to interlining with two rows of stitching, one at each edge of tape.

Stitch Seam and Stitches Thread: Thread:

Type Stitching per inch Needle Bobbin Type /Looper 103 or ----- 4-8 70 ----- 306 ----- 4-8 70 70" PAGE 13, PARAGRAPH 3.4.8.4, Delete the current requirements for the "DSCP Exclusive label" in its entirety and substitute the following:

"3.4.8.4, Exclusive Label. Each coat shall contain the Exclusive label. The jacquard woven Exclusive label shall incorporate the DLA Logo (attached) and shall specify "Made exclusively for Defense Logistics Agency" and shall include "by" and the contractor's name.

The label shall be positioned sewn above the inside left pocket and centered above the pocket opening. Label shall be approximately 2 inches square and sewn on all four sides. The proposed finished label's design shall be submitted to the contracting officer for approval."

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING

ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE

ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST

BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

CHANGES TO V-T-295E:

THREAD, NYLON; V-T-295 DATED AUGUST 1, 1985 IS HEREBY CANCELLED; FUTURE ACQUISITONS SHOULD REFER TO

THREAD, NYLON, A-A-59826 DATED 03 MARCH 2009 AS A REPLACEMENT.

ADDITIONAL INFORMATION FOR A-A-50196:

(NO CURRENT CHANGES TO A-A-50196B)

ADDITIONAL INFORMATION FOR A-A-52071:

TAPE, TEXTILE, COTTON, FOR GENERAL USE.

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD SAMPLE FOR SHADE. CLASS 5 FABRIC IS

MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-B-371:

PAGE 2, AT THE TOP OF THE PAGE AFTER "CLASS 3" ADD "AND 4". DELETE "CLASS 4 -WATER AND MILDEW-RESISTANT

FINISH 2, 2' METHYLENE BIS (4-CHLOROPHENOL)".

PAGE 3, PARAGRAPH 2.2 OTHER PUBLICATIONS. ADD THE FOLLOWING BELOW "APPLICATION FOR COPIES SHOULD BE ADDRESSED TO: ASTM INTERNATIONAL, 100 BARR HARBOR DRIVE, WEST CONSHOHOCKEN, PA. 19428"

"AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS: QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO: AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 4, PARA. 3.3.3, DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING: "3.3.3 POLYPROPYLENE YARN (AS AN ALTERNATIVE FOR TYPES III AND VII BRAID). THE YARN SHALL BE TEXTURED POLYPROPYLENE OF SUITABLE DENIER TO MEET THE REQUIREMENTS OF THIS DOCUMENT. POLYPROPYLENE BRAID IS APPLICABLE ONLY TO THE ITEMS LISTED IN

PARAGRAPH 6.7."

AFTER PARA. 3.3.4: ADD THE FOLLOWING NEW PARA: "3.3.5. 100% TEXTURED POLYESTER(AS AN ALTERNATIVE FOR TYPES I, II, IV, AND VI).THE YARN SHALL BE TEXTURED POLYESTER OF A SUITABLE DENIER TO MEET THE

REQUIREMENTS OF THIS DOCUMENT."

PAGE 5, PARA. 3.5.3 AFTER "CLASS 3" ADD "CLASS 4." AFTER "THE CLASS 3" ADD "AND 4".

PARA. 3.5.4, DELETE IN ITS ENTIRETY.

PAGE 8, ADD THE FOLLOWING TABLE IIA:

"TABLE IIA PHYSICAL REQUIREMENTS FOR POLYESTER BRAID

TYPE DIAMETER WEIGHT PER NUMBER OF ENDS PER

(INCHES) 144 YARDS CARRIERS CARRIER

(OUNCES)

MIN.

II 5/32+/-1/32 28.0 8 1

VII 11/32+/-1/32 25.0 44 1

NUMBER YARN PLY PICKS BREAKING

OF ENDS BRAID CORE PER INCH STRENGTH

IN CORE MIN. (LBS.) MIN.

1/ 8 2 3 10 140

- - - 22 200

1/ UNDYED COTTON CORE YARNS."

PAGE 10, PARA. 4.4.2.1 YARD-BY-YARD EXAMINATION, LINE 9, DELETE "1.5" AND SUBSTITUTE "1.0"

PAGE 13, TABLE V. END ITEM TESTS UNDER REFERENCED TEST METHOD COLUMN, LINES 4 AND 5 DELETE "1600" AND

SUBSTITUTE "AATCC 20"

(ref. T0821 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-B-3461:

MIL-B-3461G BUTTON, INSIGNIA, METAL,

. UNIFORM AND CAP, 9/30/79;

. AMENDMENT 6 DTD 6/24/03

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-C-3738:

WITH THE FOLLOWING INTERIM CHANGES TO MIL-C-3738:

NOTE: REDUCED AQL'S APPLY AS FOLLOWS:

PAGE 2, 2.1.2, DELETE LINES 4 THRU 7 AND

SUBSTITUTE:

"U.S. DEPARTMENT OF AGRICULTURE

METHODS OF TEST FOR GRADES OF WOOL TOP

(APPLICATION FOR TEST COPIES SHOULD BE ADDRESSED

TO THE U.S. DEPARTMENT OF AGRICULTURE, AGRI-

CULTURAL MARKETING SERVICE, WASHINGTON, DC

20402.)"

PAGE 6, AFTER 4.4.2, ADD THE FOLLOWING:

"4.4.2.1, WOOL. THE WOOL SHALL BE EXAMINED FOR

GRADE (SEE 3.3.1) IN THE UNDYED TOP FORM BY

COMPARISON WITH THE APPLICABLE U.S. STANDARD

(SEE 2.1.2). IN THE EVENT OF A DISPUTE, THE WOOL

GRADE SHALL BE DETERMINED BY THE WIDTH METHOD

(WEDGE). THE SAMPLE UNIT SHALL BE 1 YARD OF TOP,

PRIOR TO DYEING. THE SAMPLE SIZE (NUMBER OF

SAMPLE UNITS) SHALL BE AS LISTED BELOW. THE LOT

SIZE SHALL BE EXPRESSED IN UNITS OF ONE POUND.

THE RESULTS FROM EACH SAMPLE UNIT SHALL BE

REPORTED SEPARATELY. THE LOT SHALL BE UNACCEPT-

ABLE IF A SINGLE SAMPLE UNIT FAILS TO MEET THE

REQUIRED GRADE.

LOT SIZE (POUNDS) SAMPLE SIZE

800 OR LESS 2

801 UP TO AND INCLUDING

22,000 3

22,001 AND OVER 5

PARA. 4.4.3.1 POINT COUNT EXAMINATION, SECOND

LINE, DELETE "10" AND SUBSTITUTE "7". AT END OF

PARAGRAPH, ADD THE FOLLOWING: "EXCEPT THAT

BOWED OR SKEWED FILLING YARNS SHALL NOT BE

SCORED."

PAGE 7, TABLE II, LINE 1, DELETE THE FOLLOWING:

"WOOL GRADE 3.3.1 ASTM D 2130 1/

UNDER TABLE II, DELETE "1/" IN ITS ENTIRETY.

PAGE 8, DELETE PARAS. 4.5 AND 4.5.1.

PAGE 11, PARA. 6.7, DELETE ENTIRELY.

CERTIFICATE OF CONFORMANCE IS APPLICABLE FOR

THE GRADING OF WOOL IN TOP FORM.

ADDITIONAL INFORMATION FOR MIL-B-13466:

SHADE SHALL BE IN ACCORDANCE WITH ROLL NUMBER 3771

INTERIM SPECIFICATION CHANGES TO MIL-B-13466E:

PAGE 1, PARAGRAPH 1.2, CLASSIFICATION. UNDER

"TYPE II- LACE, WOVEN CLASS 1 - PLAIN WITH

VELLUM STRIPE" ADD "STYLE C - 3/4 INCH

STYLE D - 1 INCH"

PAGE 3: ADD THE FOLLOWING UNDER PARAGRAPH 2.2:

REPEAT INSULT PATCH TEST - MODIFIED DRAIZE PROCEDURE - PRINCIPLES AND METHODS OF TOXICOLOGY(4TH EDITION), A. WALLACE HAYES (EDITOR) PP 1057-1060, 2001(COPIES ARE AVAILABLE ON-LINE AT HTTP://WWW.TAYLORANDFRANCIS.CO.UK/ OR FROM TAYLOR AND FRANCIS, 325 CHESTNUT STREET, PHILADELPHIA, PA 19106.)"

PAGE 7, PARAGRAPH 3.5.3, TYPE I, CLASS 3 LINE 1,

ADD AFTER "THE 1/2 INCH BRAID" "OR LACE".

PAGE 8, PARAGRAPH 3.5.3.1, BRAID, 1/2 INCH.

- LINE 1, ADD AFTER "THE BRAID" "OR LACE".

-LINE 5, ADD AFTER "TABLE III" "OR TABLE IV"

PAGE 8 PARAGRAPH 3.5.5 LINE 4 AFTER (SEE 3.3.2).

ADD "AS AN ALTERNATE POLYESTER MAY BE USED FOR

THE FILLING YARN.

PAGE 11, TABLE IV: DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING NEW TABLE IV:

"TABLE IV. PHYSICAL REQUIREMENTS FOR TYPE II WOVEN LACE

Class/Style/ Width (Tolerance + 1/32,-0)inches/Total No. of ends (warp)min/ Weight per lin. Yard (ozs)/

1 A 1/2 128 0.20 1 B 1-1/2 300 0.50 1 C 3/4 170 0.24 1 D 1 230 0.30

2 A 3/4 172 1/ 0.24 2 B 1-3/4 456 2/ 0.60

Picks per inch (fill), min/ Number of Vellum 230 3/ 2 230 2 230 2 230 2 230 - 230 -

WEAVE PATTERN/ RIBS PER INCH (CENTER STRIPE)

1 A FILLING EFFECT -

. (SEE 3.6.1)

1 B FILLING EFFECT -

1 C FILLING EFFECT -

1 D FILLING EFFECT -

2 A FILLING EFFECT 3/ 22

2 B FILLING EFFECT 4/ 22

WARP BREAKING STRENGTH (POUNDS) MIN

1/ ARRANGED 51 LEFT; 70 CENTER STRIPE; 51 RIGHT

2/ ARRANGED 128 LEFT; 200 CENTER STRIPE; 128 RIGHT

3/ TWO PICKS PER SHED, WHEN USING NEEDLE OR SHUTTLELESS LOOM

4/ 1/4 INCH GOLD COLOR, 1/4 INCH BRANCH OF SERVICE COLOR, 1/4 INCH GOLD COLOR

5/ 1/2 INCH GOLD COLOR, 3/4 INCH BRANCH OF SERVICE COLOR

(SEE 3.5.5.1), 1/2 INCH GOLD COLOR"

PAGE 12 , ADD NEW PARAGRAPH:

"3.6.1.1 VELLUMS. THE VELLUMS ON THE LACE SHALL BE SYMMETRICAL WITH BOTH SETS OF VELLUMS THE SAME

WIDTH AND EQUIDISTANCE FROM THE EDGES OF THE LACE."

PAGE 12, ADD THE FOLLOWING NEW PARAGRAPHS:

"3.6.3 FINISH. THE TYPE II, CLASS 1 LACE SHALL BE PRESHRUNK. THE LACE MAY HAVE A FINISH TREATMENT APPLIED TO ASSIST IN STABILIZING THE LACE AND PREVENTING WAVINESS AND PUCKERING. ANY FINISH SHALL MEET

THE TOXICITY REQUIREMENTS IN 3.10.

3.6.4 DIMENSIONAL CHANGE TO DRY-CLEANING. THE TYPE II, CLASS 1 LACE SHALL NOT SHRINK OR ELONGATE MORE THAN 1 PERCENT IN THE WARP DIRECTION AFTER 1 DRY-CLEANING WHEN TESTED AS SPECIFIED IN 4.4.3.

3.6.4.1 DIMENSIONAL CHANGE TO LAUNDERING. THE TYPE II, CLASS 1 LACE, WHEN MANUFACTURED WITH A POLYESTER FILL, SHALL NOT SHRINK OR ELONGATE MORE THAN 1 PERCENT IN THE WARP DIRECTION AFTER 3

COMPLETE LAUNDERING CYCLES WHEN TESTED AS SPECIFIED IN 4.4.3."

PAGE 13, ADD THE FOLLOWING NEW PARAGRAPH:

"3.10 TOXICITY. THE FINISHED LACE SHALL NOT PRESENT A HEALTH HAZARD AND SHALL SHOW COMPATIBILITY WITH PROLONGED, DIRECT SKIN CONTACT WHEN TESTED AS SPECIFIED IN 4.4.3. CHEMICALS RECOGNIZED BY THE

ENVIRONMENTAL PROTECTION AGENCY (EPA) AS HUMAN CARCINOGENS SHALL NOT BE USED."

PAGE 19, IN TABLE VIII, UNDER "LACE ONLY", ADD THE FOLLOWING IN THEIR RESPECTIVE COLUMNS:

"DIMENSIONAL CHANGE:

TO DRY-CLEANING (1 CYCLE) 3.6.4 AATCC 158 5/

TO LAUNDERING (3 CYCLES) 3.6.4.1 AATCC 135 6/"

PAGE 19, IN TABLE VIII, UNDER "BRAID AND LACE" ADD THE FOLLOWING IN THEIR RESPECTIVE COLUMNS:

"TOXICITY 3.10 4.5.2"

PAGE 20, ADD THE FOLLOWING FOOTNOTES:

"5/ EXCEPT THE SPECIMEN SHALL BE 20-INCHES LONG AND FULL WIDTH.

6/ MACHINE CYCLE, PERMANENT PRESS; WASH TEMPERATURE, 120 + 5 degree F; TUMBLE DRY, PERMANENT

PRESS."

PAGE 21: ADD THE FOLLOWING NEW PARAGRAPH:

"4.5.2 TOXICITY TEST. IF THE TOXICITY REQUIREMENT (SEE 3.10) CAN BE DEMONSTRATED WITH HISTORICAL DATA, TOXICITY TESTING MAY NOT BE REQUIRED (SEE 6.2). WHEN REQUIRED (SEE 6.2), AN ACUTE DERMAL IRRITATION STUDY AND A SKIN SENSITIZATION STUDY SHALL BE CONDUCTED ON LABORATORY ANIMALS. WHEN THE RESULTS OF THE STUDIES INDICATE THE BRAID IS NOT A SENSITIZER OR IRRITANT, A REPEAT INSULT PATCH TEST SHALL BE PERFORMED

IN ACCORDANCE WITH THE MODIFIED DRAIZE PROCEDURE (SEE 2.2). "

PAGE 23, 6.2, ADD THE FOLLOWING:

"K. TOXICITY REQUIREMENTS (SEE 3.10 AND 4.5.2)."

(Ref. T1574)

ADDITIONAL INFORMATION FOR MIL-P-15064:

INTERIM CHANGE TO MIL-P-15064G:

AS AN ALTERNATE PADS, SHOULDER AND SLEEVE-HEAD

ADD "BLEACHED MUSLINETTE".

PAGE R, PARAGRAPH 3.2.1 PRINT CLOTH. ADD THE

FOLLOWING SENTENCE AT THE END OF THE PARAGRAPH

"AS AN ALTERNATE, THE TYPE IV SLEEVE-HEAD OUTER

COVER SHALL BE 100% COTTON MUSLIN WITH A MINUMUM

OF 44 WARP AND 36 FILLING YARNS PER SQUARE INCH.

TABLE I. MATERIAL REQUIREMENTS, ADD THE FOLLOW-

ING INFORMATION TO THE TABLE.

TYPE IV 44 BY 36"

PAGE 4: PARA. 3.2.2.1, LINE 2, AFTER "CLASS 1":

ADD "OR CLASS 2".

PAGE 4: PARA. 3.2.2.2,LINE 2, AFTER "UNBLEACHED"

ADD "OR BLEACHED".

PAGE 6, PARAGRAPH 3.2.6 WADDING. ADD THE FOLL-

ING SENTENCE AT THE END OF THE PARAGRAPH. "AS AN

ALTERNATE, THE TYPE IV SLEEVE-HEAD FILLER SHALL

BE 100% PRENEEDLED COTTON FILLER, WEIGHING A

MINIMUM OF 3.0 OUNCES PER SQUARE YARD AND A MAX-

IMUM OF 3.5 OUNCES PER SQUARE YARD"

PAGE 8, ADD "PARAGRAPH 3.5.10 TYPE IV. AS AN

ALTERNATE TYPE IV SLEEVE-HEAD SHALL MEASURE 15

INCHES (+/- 1/4 INCH) FOR MEN AND 13 INCHES (+/-1/4

INCH) FOR WOMEN."

PAGE 9, ADD THE FOLLOWING INFORMATION TO TABLE

II.

TABLE II. MANUFACTURING OPERATIONS REQUIREMENTS-

CONTINUED.

NO. REQUIRMENTS STITCH SEAM STITCHES THREAD

. TYPE TYPE PER INCH NDL BOB

1. CUTTING: "OR

C. THE MUSLIN SHALL BE SPLIT 3 INCHES (+/-1/8

INCH) IN THE BIAS DIRECTION."

2.CONSTRUCTION: "OR C. FOLD THE MUSLIN BIAS

STRIP TO FINISH TWO INCHES +/- 1/8 INCH. THE

COTTON FILLER WILL BE INSIDE THE FOLDED MUSLIN.

THE COTTON WILL BE CUT 2 -1/4 INCHES +/-1/8 INCH

WIDE. BOTH PIECES WILL BE SEWN WITH A STITCH

LINE APPROXIMATELY 1/2 INCH FROM THE FOLDED EDGE

OF THE SLEEVE HEAD. (SEE FIGURE 6, PAGE 37)"

301/401 EFA-1 3-4 70-2 70-2

PAGE 37, ADD FIGURE 6, SLEEVE HEAD, MAN'S AND

WOMEN'S TYPE IV."

ALTERNATE WOMEN'S PAD'S INSERT "B" REQUIREMENTS

THE SHOULDER PADS SHALL HAVE A TOP AND BOTTOM

COVER OF 4 OUNCES PER SQUARE YARD WHITE NEEDLE

PUNCHED POLYESTER FELT WHEN TESTED IN ACCORDANCE

WITH ASTM D-3776, OPTION C. THE FILLER SHALL BE

COTTON, ONE PIECE SHAPED TO FILL OUT THE PAD

WITH AN EVEN SMOOTH TAPER FROM CENTER TO ALL

EDGES. MULTIPLE PIECES ARE NOT ACCEPTABLE. THE

TOP COVER SHALL BE NOTCHED FOR SHOULDER SEAM

ALIGNMENT 4-3/4 INCHES FROM THE FRONT OF THE PAD

THE PAD SHALL BE SEWN IN A CONCAVE SHOULDER FIT-

TING FORM UTILIZING MULTI-LINE OF BASTING, TOTAL

ING 6 ROWS. THE PAD SHALL HAVE A COMPRESSED FIN-

ISHED THICKNESS MEASURING 3/8 +/- 1/8 INCH USING

A ONE INCH FOOT AT 0.1 PSI. THE FINISHED PAD

SHALL MEASURE 8-1/2 TO 9-1/2 INCHES IN LENGTH

AND 4-1/2 TO 5 INCHES IN WIDTH, WITH A 1/2 INCH

ARMHOLE CUTOUT ON EACH SIDE. THE PADS SHALL NOT

BE SIGNIFICANTLY ALTERED IN THICKNESS, SHAPE OR

DIMENSION AFTER BEING COMMERICALLY DRY CLEANED 3

TIMES WITH PERCHLOROETHELENE. THE PAD SHALL HAVE

A MINIMUM BREAKING STRENGTH OF 6.0 POUNDS IN THE

MACHINE DIRECTION AND A MINIMUM OF 3.0 POUNDS IN

IN THE CROSS DIRECTION WHEN TESTED IN ACCORDANCE

ASTM-D 5034, OPTION G-T OR G-E.

ALTERNATE MEN'S PAD'S INSERT "A" REQUIREMENTS

THE SHOULDER PADS SHALL HAVE A TOP AND BOTTOM

COVER OF 4 OUNCES PER SQUARE YARD WHITE NEEDLE

PUNCHED POLYESTER FELT WHEN TESTED IN ACCORDANCE

WITH ASTM D 3776, OPTON C. THE FILLER SHALL BE

COTTON, ONE PIECE SHAPED TO FILL OUT THE PAD

WITH AN EVEN SMOOTH TAPER FROM CENTER TO ALL

EDGES. MULTIPLE PIECES ARE NOT ACCEPTABLE. THE

TOP COVER SHALL BE NOTCHED FOR SHOULDER SEAM

ALIGNMENT 4-1/4 INCHES FROM THE FRONT OF THE PAD

THE PAD SHALL BE SEWN IN A CONCAVE SHOULDER FIT-

TING FORM UTILIZING MULTI-LINE OF BASTING, TOTAL

ING 6 ROWS. THE PAD SHALL HAVE A COMPRESSED FIN-

ISHED THICKNESS MEASURING 1/2 +/- 1/8 INCH USING

A ONE INCH FOOT AT 0.1 PSI. THE FINISHED PAD

SHALL MEASURE 9-3/4 TO 10/3/4 INCHES IN LENGTH

AND 5-3/8 TO 5-5/5 INCH IN WIDTH, WITH A 1/2 INCH

ARMHOLE CUTOUT ON EACH SIDE. THE PADS SHALL NOT

BE SIGNIFICATNLY ALTERED IN THICKNESS, SHADE OR

DIMENSION AFTER BEING COMMERCIALLY DRY CLEANED 3

TIMES WITH PERCHLOROETHELENE. THE PAD SHALL HAVE

A MINIMUM BREAKING STRENGTH OF 6.0 POUNDS IN THE

MACHINE DIRECTION AND MINIMUM OF 3.0 POUNDS IN

THE CROSS DIRECTION WHEN TESTED IN ACCORDANCE

WITH ASTM-D 5034, OPTION G-T OR G-E.

DEVIATION FROM MIL-P-15064F;

. PAGE 6, PARA. 3.5.1, LINE 4

. DELETE "7/8+1/8 INCH" AND

. SUBSTITUTE "1/2+1/8 INCH."

(Ref. T1553) Interim specification changes to MIL-C-15065J

PAGE 5, PARAGRAPH 3.3.2: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE:

"3.3.2 HAIRCLOTH. THE MATERIAL FOR THE SHOULDER PIECES (TYPES IV, VI, VII, XIV, XVII, XVIII AND XXII), CHEST PIECES AND REINFORCEMENT PIECE FOR TOP FRONT CORNERS (TYPE XI) SHALL BE A PLAIN WEAVE CONSTRUCTION WITH 100% SPUN POLYESTER WARP YARNS WITH 100% MONOFILAMENT POLYESTER FILLING YARNS AND SHALL CONFORM TO THE REQUIREMENTS IN TABLE A (SEE 6.7). AN ALTERNATE FOR TYPES VI, XVIII, XIX, AND XXI SHOULDER PIECE MAY INCLUDE FABRIC HAVING WARP YARNS MADE FROM 100 PERCENT COTTON, FROM 100 PERCENT POLYESTER, OR FROM ANY COMBINATION OF POLYESTER AND COTTON. THE FILLING YARNS OF THE ALTERNATE FABRIC SHALL BE MADE FROM 100 PERCENT NYLON OR POLYESTER MONO-FILAMENT AND SHALL CONFORM TO THE REQUIREMENTS IN TABLE A (SEE 6.7). THE MATERIAL SHALL BE UNDYED AND CONTAIN NO SIZING (SEE 4.4.1.1) OR

RESINS.

Table A. Material requirements

Shoulder Piece Alternate Shoulder Characteristic Requirements Piece Requirements Test Method Weight, oz/sq yd., min 5.2 4.6 ASTM D 3776 Yarns per inch, min:

Warp 52 51 ASTM D 3775

Filling 31 37 ASTM D 3775 Breaking strength, min:

Warp 160 75 ASTM D 5034 Filling 250 190 ASTM D 5034 Dry cleaning shrinkage (%), max., after 3 dry cleanings:

Warp 2.0% 2.0% Commercial dry cleaning 1/ 2/ Filling 2.0% 2.0% Commercial dry cleaning 1/ 2/ Stiffness, filling, load lbs., min Initial 0.120 0.035 ASTM D 747 1/ 2/ After 3 dry cleanings 0.115 0.061 ASTM D 747 1/ 2/

1/ Material shall be steam pressed between each dry cleaning.

2/ Each individual Service reserves the right to test for appearance, shrinkage, and stiffness in an end item configuration."

Page 48, Add the following new paragraphs:

"6.7 Suggested Sources.

6.7.1 Haircloth A suggested source for the haircloth is QST Industries, Inc., 525 West Monroe Street, Suite 1400, Chicago, IL 60661, Telephone Number (312) 930-9400. QST Part #BR-CHESTPC-50-WE has been found to meet these requirements.

6.7.2 Alternate Chest Piece. A suggested source for the alternate chest piece is Cotswold Industries, Inc., 10 East 40th Street, New York, NY 10016-0301, Telephone Number (212) 689-3432. Pattern/Number 1641 USG has been found to meet these requirements.

ADDITIONAL INFORMATION FOR MIL-DTL-21115:

CERTIFICATE OF CONFORMANCE IS APPLICABLE FOR

THE GRADE OF WOOL IN THE TOP FORM.

ADDITIONAL INFORMATION FOR MIL-C-29137:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T1562)

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1" INSERT "TYPE X1-

"STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X - CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT LISTED IN THE DODISS SHALL BE THE ISSUES OF THE NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE

DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR KNIT. WHEN

SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1. TYPE X1 SHALL BE STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF CHAINSTITCHING IS SEWN IN THE MACHINE DIRECTION OF THE SUBSTRATE IN

ORDER TO REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING CHAINSTITCH STITCH TYPE WITH

CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS FUSIBLE SEAM TAPE AND

CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24, DELETE "45" AND SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND 3 DELETE "1600" AND SUBSTITUTE

"AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER LAUNDERING/DRY CLEANING).

DELETE THE FIRST AND SECOND SENTENCES IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL PART FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL STABILITY AND ABRASION

RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE FOLLOWING BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES, OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED TO DETERMINE IF DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2

ADDITIONAL INFORMATION FOR MIL-STD-1608:

INTERIM CHANGES TO MIL-STD-1608C:

PAGE 14, BEFORE "COAT BUTTONED ON FORM" ADD "B."

PAGE 17: DEFECT E.4., LINE 1, AFTER "TO" ADD

"ROLL OUTWARD AND NOT".

PAGE 19: TABLE II, AFTER DEFECT XXI SLEEVE PARA.

E. ADD "NOTE: THE NORMAL HANGING POSITION FOR

THE FRONT EDGE OF THE SLEEVE IS THE CENTER OF

THE TOP EDGE OF THE LOWER PATCH POCKET."

PAGE 22: BEFORE "XXIX", ADD "C. COAT SPREAD OUT

ON TABLE"

PAGE II, ADD NEW DOCUMENT "MIL-C-29628 (NU)

COAT, WOMEN'S, BLUE DRESS".

MIL-STD-1608C PAGE 7, TABLE I DELETE IN ITS

ENTIRETY AND SUBSTITUTE "TABLE I SAMPLING

PROVISIONS".

NORMAL INSPECTION

LOT SZ SAMP SZ MAX ACCP MAX ACCP PT VALU

. NO. FOR

. SELECTED 3&2 PT 3,2,1 PT

. (*DEFECT) DEFECTS DEFECTS

UP THRU 90 20 0 3 7

91- 150 32 0 4 11 151-280 50 0 7 13 281-500 80 0 9 19 501-1200 125 1 14 27 1201-3200 200 1 18 36 3201-10,000 315 2 25 55 10,001-35,000 500 3 36 81

35,001 & OVER 800 5 55 122

TIGHTENED INSPECTION

UP THRU 90 20 0 3 5

91-150 32 0 3 7 151-280 50 0 5 11 281-500 80 0 7 14 501-1200 125 1 11 21 1201-3200 200 1 13 31 3201-10,000 315 2 22 47 10,001-35,000 500 3 33 69

35,001 & OVER 800 5 49 104

REDUCED INSPECTION

UP THRU 280 20 0 2-4 7

281-500 32 0 3-7 12 501-1200 50 0 6-10 15 1201-3200 80 0 7-10 24 3201-10,000 125 1 13-18 31 10,001-35,000 200 1 17-23 47

35,001 & OVER 315 2 23-29 69

NOTE: FOR THE REDUCED POINT VALUES OF THE

REDUCED INSPECTION ON 3 & 2 POINT DEFECTS. IF

THE FIRST VALUE IS EXCEEDED, BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

(Ref. T0344)

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF

SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND

LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)