Army Coat MDW Mens inspection text pgc01846 PD1502.pdf

INSPECTION TEXT- PGC01846 GLPD 15-02

PRES/PACK: HANGER PACK (MIL-C-44192(GL)

THE PACKAGING CASE LOT QUANTITY IS 12

PALLETIZATION IAW MIL-STD-147.

ARROW UP MARKINGS SHALL APPEAR ON ALL HANGER PACKS

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129 AND CHANGE NOTICE 3.

ADDITIONAL INFORMATION FOR MIL-C-44192:

INTERIM CHANGES TO MIL-C-44192:

3.2.2 HANGER BARS. THE LENGTH OF THE HANGER BARS (FOR TYPES I, II, AND III CONTAINERS) SHALL BE AS SPECIFIED IN TABLE I. THE STYLE OF THE HANGER BARS SHALL BE AS SPECIFIED IN

3.2.2.1 OR 3.2.2.2 (SEE 6.2). THE HANGER BARS SHALL BE FABRICATED FROM SHEET STEEL OR PLASTIC CAPABLE OF SUPPORTING A MINIMUM OF 75 LBS. DURING TRANSPORTATION. THE BAR ASSEMBLY SHALL CONSIST OF A 1 1/2 ± 1/4 INCH RECTILINEAR TUBE WITH AT LEAST THREE COMPLETE SIDES AND TWO END CLIPS FREE OF ROUGH EDGES. THE END CLIPS SHALL MEASURE

A MINIMUM OF 4 INCHES IN LENGTH AND 1-1/2 INCHES IN HEIGHT. THE BAR SHALL BE

INTERLOCKED TO THE END CLIPS AND SHALL BE DEFORMED SO THAT THE END CLIPS CANNOT BE

REMOVED. THE BAR SHALL BE PROVIDED WITH A LOCKING DEVICE (LOCKING CAP) THAT WILL

SECURELY HOLD THE HANGERS TO THE BAR. END CLIPS SHALL BE MOUNTED TO THE BAR SO

THAT WHEN THE HANGER BARS ARE INSTALLED IN THE CONTAINER, THE BAR, WITH LOCKING

DEVICE, IS HELD FLUSH WITH THE TOP OF THE CONTAINER. THE END CLIPS SHALL SNUGGLY CUP

THE UPPER EDGE OF THE CONTAINER WHERE THE EDGE SHALL BE TWO THICKNESSES OF

DOUBLE WALL CORRUGATED FIBERBOARD (SEE 3.2.1.1).

PAGE 4, PARA 3.2.4 AFTER "II" ADD "FOR DRESS COATS AND TYPE "III" FOR ALL WEATHER COATS."

PAGE 11, PARA 30.4, DELETE AND SUBSTITUTE:

"30.4 CONTAINER CLOSURE. THE CONTAINER SHALL BE CLOSED BY THE USE OF 3 INCH WIDE TAPE

CONFORMING TO TYPE II, CLASS 2 OF PPP-T-45. THE TAPE SHALL BE CENTERED OVER EACH

EXPOSED SEAM INCLUDING THE DISPENSING DOOR SLITS AND EXTENDED OVER ALL

THE CORNERS AND EDGES WITH A MINIMUM OF 2 INCHES ONTO THE ADJACENT BOX PANELS. THE MANUFACTURERS JOINT AND THE EDGES AROUND THE BOTTOM OPENING OF THE LID AFTER IT IS

PLACED OVER THE CONTAINER BOX BODY NEED NOT BE TAPED.".

NOTE: WHEN HANGER PACKS ARE SPECIFIED FOR ALL- WEATHER COATS, COATS SHALL BE

PACKAGED, MARKED AND PALLETIZED IN ACCORDANCE WITH MIL-C-44192,

WITH FRONTS LAPPING AND BUTTONED.THE FOLLOWING APPLIES:

TEN (10) COATS OF ONE CLASS AND SIZE SHALL BE PACKED IN A TYPE I CONTAINER (HANGER

PACK)

EXCEPT THAT THE DIMENSIONS OF THE CONTAINER SHALL APPROXIMATE 24 X 21 INCHES AND

THE DEPTH OF THE CONTAINER SHALL BE 48 +0/-2 INCHES.

HANGER PACK SHIPPING CONTAINERS SHALL BE MARKED A/C TO IDENTIFY THE LEVELS OF

PACKAGING/PACKING.

(REF. T0806)

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL

SHIPPING

CARTONS ON WHICH THE NSN APPEARS".

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL)

SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T

ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY

REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS; THE PACKING

LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"ALL WOOD PACKAGING MATERIAL (WPM) ACQUIRED BY DOD MUST MEET REQUIREMENTS OF

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES (ISPM) 15, "GUIDELINES FOR

REGULATING WOOD PACKAGING MATERIALS IN INTERNATIONAL TRADE." DOD SHIPMENTS INSIDE AND OUTSIDE OF THE UNITED STATES MUST MEET ISPM 15 WHENEVER WPM IS USED TO SHIP DOD CARGO, OR WHEN WOOD IS BEING ACQUIRED BY DLA FOR FUTURE USE AS PACKAGING MATERIAL.

WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAME AND CLEATS. PACKAGING MATERIALS EXEMPT FROM THE

REQUIREMENTS ARE MATERIALS THAT HAVE UNDERGONE A MANUFACTURING PROCESS, SUCH

AS CORRUGATED FIBERBOARD, PLYWOOD, PARTICLEBOARD, VENEER, AND ORIENTED STRAND

BOARD (OSD). ALL WPM SHALL COMPLY WITH ONE OF THE FOLLOWING OFFICIAL QUALITY

CONTROL PROGRAMS:

HEAT TREATMENT (HT) OR KILN DRIED HEAT TREATMENT (KD HT) IN ACCORDANCE WITH

AMERICAN LUMBER STANDARD COMMITTEE, INCORPORATED (ALSC) WOOD PACKAGING MATERIAL

PROGRAM AND WPM ENFORCEMENT REGULATIONS (SEE HTTP://WWW.ALSC.ORG/; OR

ALL WPM SHALL INCLUDE CERTIFICATION/QUALITY MARKINGS IN ACCORDANCE WITH THE ALSC

OR NWPCA STANDARDS, AS APPLICABLE. MARKINGS SHALL BE PLACED IN AN UNOBSTRUCTED

AREA THAT WILL BE READILY VISIBLE TO INSPECTORS. PALLET MARKINGS SHALL BE APPLIED TO

THE STRINGER OR BLOCK ON DIAGONALLY OPPOSITE SIDES OF THE PALLET AND BE

CONTRASTING AND CLEARLY VISIBLE.

ALL CONTAINERS SHALL BE MARKED ON A SIDE OTHER THAN THE TOP OR BOTTOM,

CONTRASTING AND CLEARLY VISIBLE. ALL DUNNAGE USED IN CONFIGURING AND/OR SECURING

THE LOAD SHALL ALSO COMPLY WITH ISPM 15 AND BE MARKED WITH AN ASLC APPROVED

DUNNAGE STAMP. FAILURE TO COMPLY WITH THE REQUIREMENTS OF THIS RESTRICTION MAY

RESULT IN REFUSAL, DESTRUCTION, OR TREATMENT OF MATERIALS AT THE POINT OF ENTRY.

THE AGENCY RESERVES THE RIGHT TO RECOUP FROM THE CONTRACTOR ANY REMEDIATION

COSTS INCURRED BY THE GOVERNMENT."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT

EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE

PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS.

THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO

THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF

A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED

QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL)

SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T

ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY

REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING

LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) REQUIRED

(REF. T8379; NOV. 08, 2006)

THE CONTRACTOR SHALL MAINTAIN TRACEABILITY RECORDS FOR ALL COMPONENT PARTS USED

TO MANUFACTURE THE END ITEM PRODUCT. ALL COMPONENT PARTS LOT IDENTIFICATION SHALL

BE TRACEABLE VIA THE END ITEM PRODUCT'S LOT NUMBER. SUBCONTRACTOR'S COMPONENT

PART LOT INFORMATION SHALL ENABLE TRACEABILITY TO THE RAW MATERIALS USED IN THE

COMPONENT PART. RECORDS SHALL BE MAINTAINED AND READILY AVAILABLE FOR GOVERNMENT

REFERENCE.

FOR END ITEM PRODUCTS IDENTIFIED WITH INDIVIDUAL SERIAL NUMBERS, THE TRACEABILITY

REQUIREMENTS LISTED ABOVE SHALL BE TRACEABLE VIA THE INDIVIDUAL SERIAL NUMBER.

52.211-9P08 - REVIEW AND ANALYSIS OF SPECIFICATIONS FOR ADEQUACY.

ADDITIONAL INFORMATION FOR ASL:

THE ACCEPTABLE SUPPLIER LISTING (ASL) AND QUALIFIED LABORATORY LISTING (QLL) ARE NO

LONGER VALID DOCUMENTS AND WILL NOT BE PUBLISHED IN THE FUTURE. THE POINT OF

CONTACT FOR QUESTIONS PERTAINING TO LABORATORIES AND SUPPLIERS IS THE

PROCUREMENT BUYER, INDICATED IN THE SOLICITATION OR CONTRACT. QUESTIONS SHOULD BE

PROVIDED IN WRITING TO THE DESIGNATED BUYER.

CLAUSE 52.246-9032 IDENTIFICATION OF QUALIFIED LABORATORY AND SOURCE SAMPLING

APPLIES.

MANDATORY USE OF STATISTICAL PROCESS CONTROLS

I. GENERAL REQUIREMENTS:

A. THE OFFEROR AGREES TO MANAGE AND IMPROVE PROCESS PERFORMANCE THROUGH THE

EVALUATION OF THE QUALITY OF THE PRODUCT AT THE PRIME CONTRACTOR AND/OR

SUBCONTRACTOR FACILITIES, USING STATISTICAL PROCESS CONTROL (SPC) TECHNIQUES.

B. MINIMUM CRITERIA ARE ESTABLISHED IN THE AMERICAN SOCIETY OF QUALITY CONTROL

(ASQC) STANDARDS B.1, B.2 AND B.3 (FORMERLY THE ANSI STANDARDS Z1.A, Z1.2 AND Z1.3).

ALTERNATE SPC TECHNIQUES, SUCH AS SHORT RUN METHODS ARE ALSO ALLOWED WHERE

APPLICABLE.

C. THIS QUALITY ASSURANCE PROVISION (QAP) APPLIES TO ALL WORK PERFORMED AT THE

PRIME AND/OR SUBCONTRACTOR FACILITIES.

D. EXCLUSION OF SPC PLAN SUBMISSION: OFFERORS WHO CONSIDER THEMSELVES ELIGIBLE

FOR EXCLUSION OF THE SPC PLAN SUBMISSION BASED ON SATISFACTORY UTILIZATION OF A

PREVIOUSLY APPROVED SPC PLAN FOR THE IDENTICAL OR SIMILAR SUPPLIES ARE TO SUBMIT A

WRITTEN REQUEST FOR EXCLUSION (RFE) TO THE PROCURING ACTIVITY.

TECHNICAL HISTORY/WS DATA:

THE PGC/NSN FOR THIS ITEM HAS BEEN REVIEWED IN ACCORDANCE

WITH DATA CLEANSING TEMPLATE, AND IS SUITABLE FOR

TRANSFER TO BSM PHASE 2 AT TIME OF REVIEW.