MS 082 Toilet Partitions Benches and Accessories.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

BENCHES

A8054

PROJECT: Dyess Air Force Base - Building 8040 Repair Maintenance Shop

1081 2nd Street

Dyess AFB, TX

79607

CONTRACTOR: Farr Builders, LLC 3401 S. Gevers Ste. 1

San Antonio, TX

78210

ARCHITECT: Castillo Architects 981 Southpark Dr

Littleton, CO

Prepared By: Tex-Oma Builders Supply Co.

2701 Commerce Street

Wichita Falls, Texas 76301

Date: March 20, 2018

DYESS AIR FORCE BASE – BLDG 8040

BENCH CLARIFICATIONS

1. Please select a color finish per cut sheet instruction. Color examples located below.

juan.aguilar

Stamp

Dyess Air Force Base - Building 8040

March 20, 2018 Page 1 of 1

Hardware Schedule

HEADING #TA.2 (SET #TA)

1 Other Door #DLR MEN

Opening Description:

1 Bench, Plastic LENOXPEDESTAL BRAD

HEADING #TA.3 (SET #TA)

1 Other Door #DLR WOMEN

HEADING #TA (SET #TA)

1 Other Door #CLR MEN

HEADING #TA.1 (SET #TA)

1 Other Door #CLR WOMEN

LENOXPEDESTAL

Lenox Locker Pedestal Bench

© 2017 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

800 BRADLEY (800 272 3539) +1 262 251 6000

bradleycorp.com

Page 1 of 1 1/23/2017 This information is subject to change without notice.

Bradley_LenoxLocker_PedestalBench

• Tough, attractive, solid plastic never needs painting; resists dents and scratches

• Impervious to moisture — benches will not rust or delaminate

• Durable, vandal resistant construction

• Wide range of lengths and colors

• 20-year warranty against rust, delamination or breakage under normal use*

Construction - Standard Features Bench Top Constructed of 1½" thick High Density Polyethylene (HDPE) with homogeneous color and a matte finish texture.

Pedestal 17" Black anodized aluminum pedestal with welded aluminum flanges. Anchored to floor and bench top with hardware provided. Also available without pedestals or hardware.

Width 24" to 96" in 1 foot increments (custom sizes available).

Depth 9½", 12", 18" or 24" depth (custom sizes available).

Height 18½" height (ADA compliant).

* Normal use further defined as lockers installed in a climate-controlled environment, away from direct sunlight.

Model Description LENOXPEDESTAL Pedestal Bench

Required Selections (Must select one from each category)

Width (select one):

Depth (select one):

Height (select one):

18.5-HGT 18½" High Bench

9½", 12", 18" or 24" (Depth)

Ø 6"

Ø 15⁄8" Ø 4¾"

Bolt Hole Circle

3⁄8" Radius All Edges 1½"

18½"

5/8"

24" to 48" (Width)

6"6"

60" to 84"

96"

28" 28" 28"

Equal Space

9½", 12", 18" or 24"

(Depth)

9½", 12", 18" or 24"

(Depth)

Equal Space

Lockers are non-cancelable and non-returnable.

Required Selections Cont... (Must select one from each category)

Locker Color (select one):

Hardware Type (select one):

Rectangle

TOILET ACCESSORIES

Section 10 28 13

Date: March 20, 2018

Dyess Air Force Base - Building 8040 DOOR HARDWARE

A8054 SECTION 08710

March 20, 2018 Page 1 of 3

1 Mirror 747F-024360S MIHW

2 TOILET TISSUE DISP. BRAD

1 TOWEL/WASTE UNIT 2277-110000 BRAD

1 Soap Dispenser BRADLEY 4 5/8" x 10 9/16" BRAD

2 SHELF 8" X 16" 758-16000 BRAD

2 TOILET TISSUE DISP. 522-000000 BRAD

1 Soap Dispenser BRADLEY 4 5/8" x 10 9/16" BRAD

2 Napkin Disposal 4781-11 BRAD

1 Napkin/Tampon Vendor BRADLEY 16 1/2" x 27 7/8" BRAD

HEADING #TA.2 (SET #TA)

1 Other Door #DLR MEN

2 Soap Dispenser BRADLEY 4 5/8" x 10 9/16" BRAD

1 COAT RACK 36" 4 HOOKS 9944-000 BRAD

March 20, 2018 Page 2 of 3

HEADING #TA.3 (SET #TA)

1 Other Door #DLR WOMEN

2 Soap Dispenser BRADLEY 4 5/8" x 10 9/16" BRAD

HEADING #TA.4 (SET #TA)

1 Other Door #IAP MEN

1 Other Door #IAP WOMEN

2 TOILET TISSUE DISP. 522-000000 BRAD

HEADING #TA.5 (SET #TA)

1 Other Door #RESPIRATOR ROOM

HEADING #TA.6 (SET #TA)

1 Other Door #JANITOR

1 COAT RACK 36" 4 HOOKS 9944-000 BRAD

March 20, 2018 Page 3 of 3

HEADING #Div 10.1 (SET #DIV 10) 1 Other Door #PAINT WORKSHOP

1 Other Door #BLASTING WORKSHOP

2 EYE WASH HAND/FOOT #19314LL MIAC

Frameless Mirror

© 2014 Bradley

Orders composed of products indicated as Bradex® will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley.

Page 1 of 2 4/28/2014

Bradley_Mirror_747

Frameless mirror:

Model 747-XXXX with Clip Fasteners (Specify width and height)

Model 747-024360 (24" x 36") Bradex®

Product Materials MIRROR: first quality ¼" float glass, thermosetting infrared-cured paint backing.

Manufactured in accordance with ASTM C 1036 and ASTM C 1503. Edges ground and polished smooth.

Installation Verify all rough-in dimensions prior to installation.

MODEL 747: Secure mounting clips (metal) to wall with screws included, then engage mirror into clips.

Guide Specification Frameless mirror shall be of first quality 1/4" float glass, guaranteed for 15 years against silver spoilage. Edges ground and polished smooth.

Frameless Mirror shall be Bradley Model 747-______" W x______" H (specify width and height).

Model 747 series frameless mirrors can be fabricated to a maximum size of 60"W x 96"H.

ADA Compliant Consult local and national accessibility codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer.

Toilet Tissue Dispenser

Page 1 of 1 7/17/2017

Bradley_TPDispenser_522

Model 522 — Bradex®

Controlled Delivery Dual Roll (For Single Roll see Model 505)

UNIT: diecast zinc. Copper and nickel polished chrome-plated finish.

Capacity Two standard core toilet tissue rolls through 5" in diameter and 4½" wide.

Operation Push button unlocks support arms to permit servicing of unit. Tension spring on stationary arm controls paper delivery.

Verify all rough-in dimensions prior to installation. Secure to wall with mounting screws (included) at holes provided.

Surface-mounted toilet tissue dispenser shall be chrome-plated diecast zinc and hold two standard core toilet tissue rolls. Tension spring controls paper delivery.

Overall dimensions: 10-1/2"W x 27⁄16"H x 4-1/4"D.

10½ (267mm)

4¼" (108mm)

3" (76mm)

1³⁄₁₆" (30mm)

2⁷⁄₁₆" (62mm) order at the factory. There is no pricing penalty for this service from Bradley.

Page 1 of 2 4/14/2011

Bradley_CombiDispenser_2277_10_11

Towel Dispenser/Waste Receptacle

Model 2277 — Recessed Bradex®

Model 2277-10 — Semi-Recessed (recesses 3½"; projects 7") Model 2277-11 — Surface-Mounted (projects 10½")

Contemporary Series — Satin Finish

CABINET: 22 gauge stainless steel with exposed surfaces in architectural satin finish. Welded construction with seamless corners and burr-free edges.

DOOR: 18 gauge stainless steel. ½" return for maximum rigidity. Concealed full length stainless steel piano hinge and 2 tumbler locks keyed like other Bradley units.

TOWEL DISPENSER: furnished (manufactured by others). Rolled edge on dispenser opening.

WASTE RECEPTACLE INSERT: leakproof molded plastic.

Towel Dispenser — one standard core 8" or 9"W x 800'L roll paper towel Waste Receptacle Insert — 10.5 gal. (1.4 cu. ft.)

Towel dispenser delivers preset length of towel (2½", 4" or 5" per stroke).

Waste receptacle insert removable by unlocking cabinet door. Operates with less than 5 lbs. of force.

Verify all rough-in dimensions prior to installation. Recessed unit requires rough wall opening 15¾"W x 39½"H x 10¼"D (Semi-recessed unit only 3½" deep). Secure to framing with mounting screws (included) at holes provided.

Shim at screw points as required. Surface-mounted units must have holes drilled by installer.

Recessed combination towel dispenser and waste receptacle shall be fabricated of heavy gauge stainless steel with exposed surfaces in satin finish. Cabinet door of 18 gauge stainless steel with full length concealed piano hinge and secured by 2 tumbler locks. Towel dispenser shall be activated with less than 5 lbs. of force and have the capacity to hold one standard core 8" or 9"W x 800'L roll paper towel. Removable 10.5 gal.

leakproof molded plastic insert for waste receptacle.

Overall dimensions: 173⁄8"W x 41¼"H x 10½"D.

Consult local and national accessibility codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer.

order at the factory. There is no pricing penalty for this service from Bradley.

Page 2 of 2 4/14/2011

Bradley_CombiDispenser_2277_10_11

Dimensions

Dim. "A" Key Surface:

For Dim. "A"

Top of Rough Wall Opening

Bottom of Rough Wall Opening

Actuator top to finished floor

48" (1219mm) 52½" (1334mm) 13" (330mm)

45" (1143mm) 49½" (1257mm) 10" (254mm)

42" (1067mm) 46½" (1181mm) 7" (178mm)

40" (1016mm) 44½" (1130mm) 5" (127mm)

Rough wall opening:

Surface Mount: No rough opening, see overall dimensions

Recessed: 15¾" (401mm) Wide x 39½" (1004mm) High x 10¼" (261mm) Deep

Recessed: 15¾" (401mm) Wide x 39½" (1004mm) High x 3½" (89mm) Deep

41¼" (1048mm)

½" (13mm)

8" (203mm)

17³⁄₈" (441mm)

26⁵⁄₈" (676mm)

39¹⁄₈" (994mm)

Dim. "A" to finished floor

15¼" (387mm)

10⁹⁄₁₆" (268mm)

7⁹⁄₁₆" (192mm)

3¹⁄₁₆" (78mm)

2³⁄₈" (60mm)

2" (51mm)

35¹⁄₈" (892mm)

8" (203mm)

6A01 Soap Dispenser

© 2015 Bradley

Page 1 of 2 4/8/2014

Bradley_SoapDispenser_6A01

Diplomat Series

BODY: Heavy gauge stainless steel with exposed surfaces in architectural satin finish. Front has matching curvature to other Bradley Diplomat washroom accessories.

WALL PLATE: ABS plastic.

RESERVOIR: reusable plastic, holds 27 oz.

BATTERY BOX: Plastic, holds (4), "AA" Alkaline batteries, not included.

27 oz.(800 ml) of bulk foam soap

Place hands under soap spout and hold to dispense liquid. (2"-3" sensing range.) Sight gauge indicates refill time. Refill by unlocking lock with special key (supplied), swinging open dispenser body. Remove cap to refill internal soap tank.

Verify all rough-in dimensions prior to installation. Secure separate mounting bracket with mounting screws (included) at holes provided. Unlock the cover. Open and remove tank. Secure unit to wall by installing the mounting screws. Install batteries (not included). Fill tank with premixed, bulk foam soap. Close and lock the cover.

Soap Dispenser: Bradley Corp. Diplomat Series Model 6A01: Surface-mounted automatic soap dispenser, with face formed with contemporary contours, radii, and finish matching related accessories in manufacturer's designer series. Capacity 27 oz (800 ml). Equipped with hinged cover and completely concealed mounting plate.

Vandal resistant filler hole cover and sight gauge. Corrosion-resistant foam soap valve.

Overall dimensions: 4⁵⁄₈"W x 10⁹⁄₁₆"H x 4³⁄₁₆"D.

Model 6A01-11—Surface-Mounted Foam Tank Type Vertical Bradex®

For information on Warranties, Maintenance and BAA/ARRA Compliance, visit our web site at:

bradleycorp.com/products/accessories/.

Consult local and national accessibility codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer.

MasterFormat Title: Commercial Toilet Accessories MasterFormat Number: 10 28 13.13

OmniClass Title: Soap Holders, Dispensers OmniClass Code: 23.40.20.21.34

6A01 Soap Dispenser

Page 2 of 2 4/8/2014

Bradley_SoapDispenser_6A01

43⁄16" (106mm)

45⁄8" (117 mm)

109⁄16" (268 mm)

Dim. "A" Key Surface:

For Dim. "A" Locate Top of

Unit Locate Bottom of

Unit

Bottom of dispensing tube to finished floor

48" (1219mm) 58" (1473mm) 47¹⁄₁₆" (1205mm)

45" (1143mm) 55" (1397mm) 44¹⁄₁₆" (1129mm)

42" (1067mm) 52" (1321mm) 41¹⁄₁₆" (1053mm)

40" (1016mm) 50" (1270mm) 39¹⁄₁₆" (1002mm)

Dim. "A" to finished floor

755, 756, 758 Shelf

Page 1 of 1 4/5/2013

Bradley_Shelf_755_756_758

Surface-mounted shelf:

Model 755-XX (5" depth, specify length)

Model 756-XX (6" depth, specify length)

Model 758-XX (8" depth, specify length)

SHELF: 18 gauge stainless steel with exposed surfaces in architectural satin finish. End brackets are integral.

CENTER BRACKETS: (shelves over 24" length) 16 gauge stainless steel. Welded to shelf.

Verify all rough-in dimensions prior to installation. Secure to wall with mounting screws (included) at holes provided.

Length No. of Center Brackets

6" to 24" 0

25" to 48" 1

49" to 72" 2

73" to 96" 3

97" to 112" 4

Surface-mounted shelf shall be fabricated of 18 gauge stainless steel with exposed surfaces in satin finish and integral end brackets. Shelves over 24" long shall have 16 gauge intermediate support brackets of matching stainless steel.

Surface-Mounted Shelf shall be Bradley Model 755, 756, 758-______" (specify length).

Bradex® Models Depth

(Inches) Length

Overall

Dimension

Overall

(Millimeters)

Standard Model Number

5" 12" 5 x 12 127 x 305 755-12

5" 18" 5 x 18 127 x 457 755-18

8" 24" 8 x 24 203 x 610 758-24

3¾" (95mm)

5⁄8" (16mm)

¾" (19mm)

Center Brackets spot-welded to Shelf

2" (51mm)

Length as Required

3⁄8" (10mm) 18" (457mm)

9943, 9944, 9945, 9946 Hat and Coat Rack

Page 1 of 1 2/20/2013

Bradley_CoatRack_9943_44_45_46

Model 9943 – 3 Hooks Bradex®

Model 9944 – 4 Hooks

Model 9945 – 5 Hooks

Model 9946 – 6 Hooks

BACKPLATE: 22 gauge stainless steel with exposed surfaces in architectural satin finish. Backplate is open through the center and does not have end caps.

HOOKS: 14 gauge stainless steel

Verify all rough-in dimensions prior to installation. Secure to wall with mounting screws (included) at holes provided.

Surface-mounted hat and coat rack shall be fabricated of 22 gauge stainless steel in satin finish. Hooks shall be of 14 gauge stainless steel.

Dim. “A”

Dim. “B”

7¼" (184mm)

25⁄8" (67mm)

Mounting Holes

Dim. “C”

Model No. Dim. “A” Dim. “B” Dim. “C” Hooks

9943 24" (610 mm) 9" (229 mm) 3" (76 mm) 3

9944 36" (914 mm) 10" (254 mm) 3" (76 mm) 4

9945 48" (1219 mm) 11" (279 mm) 2" (51 mm) 5

9946 60" (1524 mm) 10¾" (273 mm) 3¼" (83 mm) 6

MODEL 9944 SHOWN

9983, 9984, 9985, 9986 Utility Shelves

Page 1 of 1 2/20/2013

Bradley_UtilityShelf_9983_84_85_86

Model 9983 – 2 Hooks/3 Holders

Model 9984 – 3 Hooks/4 Holders Bradex®

Model 9985 – 4 Hooks/5 Holders

Model 9986 – 5 Hooks/6 Holders

SHELF: 18 gauge stainless steel with exposed surfaces in architectural satin finish.

BRACKETS: 16 gauge stainless steel with exposed surfaces in architectural satin finish.

HOOKS: 14 gauge stainless steel HOLDERS: spring-activated rubber cams on plated steel retainers. Will hold a mop or broom handle with a diameter between 5/8" and 1".

DRYING ROD: 1/4" diameter solid stainless steel with satin finish.

Weight of mop or broom holds handle in place.

Verify all rough-in dimensions prior to installation. Secure to wall with mounting screws (not included) at holes provided.

Surface mounted utility shelf shall be fabricated of 18 gauge stainless steel in satin finish with 16 gauge brackets and 14 gauge hooks. Drying rod of 1/4" stainless steel. Mop and broom holders to have spring-activated rubber cams.

“C”2-11/16" (68 mm)

6-5/8" (168 mm)

DRYING ROD

MOP HOLDERS

(203 mm)

“B”

6-1/8" (156 mm)

1-9/16" (40 mm)

HOOKS

“A”

Model No. Dim. “A” Dim. “B” Dim. “C” Hooks Holders

9983 30" (762 mm) 16-3/4" (425 mm) 12" (305 mm) 2 3

9984 36" (914 mm) 22-7/8" (581 mm) 10" (254 mm) 3 4

9985 42" (1067 mm) 28-7/8" (733 mm) 9" (229 mm) 4 5

9986 48" (1219 mm) 34-7/8" (886 mm) 8-3/8" (213 mm) 5 6

Napkin/Tampon Vendor

Page 1 of 2 12/11/2017

Bradley_Vendor_407_11

Contemporary Series — Satin Finish

CABINET fabricated of 22 gauge stainless steel with exposed surfaces in architectural satin finish. All welded construction.

DOOR fabricated of 18 gauge stainless steel with exposed surfaces in architectural satin finish. Secured with full-length piano hinge and two tumbler locks keyed like other Bradley accessory units.

COIN BOX fabricated of 22 gauge stainless steel. Secured with tumbler lock keyed differently than door for security. Coin mechanisms are available with free, $.10, $.25, $.50, $1.00, Canadian $.25 or Canadian Loonie denomination.

18 napkins (3" x 4¼" x 1" box) and 28 tampons (51⁄8" long x ¾" diameter tube).

Dispenses most popular brands.

Insertion of coin permits clockwise rotation of handle to dispense product. Unit will not accept coin when product is empty. Access door allows refilling of product and emptying of coin box.

Verify all rough-in dimensions prior to installation.

Recessed Unit: Requires rough wall opening 161⁄8"W x 277⁄8"H x 4"D. (fully recessed). Insert cabinet into wall opening and secure to framing (by installer) with included screws through holes provided. Shim at screw points as required.

Surface Unit: Secure cabinet to wall with screws (not included) at holes provided.

Surface and recessed combination napkin/tampon vendor shall be fabricated of 22 gauge stainless steel with exposed surfaces in satin finish. Door shall be fabricated of 18 gauge stainless steel with a full-length piano hinge and two tumbler locks keyed like other Bradley units. Coin box shall be secured with differently keyed lock for extra security. Two coin mechanisms shall permit dispensing eighteen napkins and twenty-eight tampons with free, $.10, $.25, $.50, $1.00, Canadian $.25 or Canadian Loonie denomination.

Overall dimensions: 17¼"W x 291⁄8"H x 43⁄8"D.

Select Model Currency Description Suffix

US Free -40

US 10¢ -42

US 25¢ Bradex® -45

Foreign Canadian 25¢ -45

US 50¢ -43

US $1.00

-44

Foreign Canadian Loonie

Napkin/Tampon Vendor

Page 2 of 2 12/11/2017

Bradley_Vendor_407_11

Recessed

Surface-Mounted

291⁄8" (740mm)

(13mm)4"

(102mm)

7½" (191mm)

26" (660mm)

9" (229mm)

(13mm)

4½" (114mm)

273⁄8" (695mm)

1713⁄16" (437mm)

155⁄8" (397mm)

7½" (191mm)

9½" (241mm)

26½" (673mm)

1115⁄16" (303mm)

25⁄8" (67mm)

4781-11 Napkin Disposal

© 2016 Bradley

Page 1 of 1 11/17/2016

Bradley_WasteReceptacle_4781-11

Model 4781-11 — Surface-Mounted Bradex®

Standard Series — Satin Finish

COVER: 22 gauge stainless steel with exposed surfaces in architectural satin finish. Heavy-duty stainless steel piano hinge.

CONTAINER: 22 gauge stainless steel with exposed surfaces in architectural satin finish. All welded construction with rounded front corners.

Top opens for removal of waxed paper liner. Box of 500 waxed paper liners are available by ordering part number P11-022

Verify all rough-in dimensions prior to installation. Secure to wall or partition with mounting screws (included) at holes provided.

Surface-mounted napkin disposal shall be fabricated of 22 gauge stainless steel with exposed surfaces in satin finish. Top attached by piano hinge.

Overall dimensions: 8"W x 11-3/8"H x 4-1/4"D.

Dim. "A" Key Surface: For Dim. "A" Top of Unit Bottom of Unit

Waste receptacle top lip to finished floor

40" (1016mm) 40" (1016mm) 28½" (724mm)

36" (914mm) 36" (914mm) 24½" (622mm)

32" (813mm) 32" (813mm) 20½" (521mm)

Rough wall opening:

Surface Mount: No rough opening, see overall dimensions

Consult local and national accessibility codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer.

4-1/4" (108mm)

1³⁄₈" (35mm)

1-5/8" (41mm)

5¹⁄₈" (130mm)

Mounting Hole

(qty. 2)

(203mm)

11-3/8" (289mm)

S19314LL, S19314UU

Combination Drench Shower and Halo™ Eyewash with Foot Pedal

© 2018 Bradley

Page 1 of 2 3/6/2018

Bradley_SafetyCombi_S19314LL_UU

• Halo™ and SpinTec™ Deliver the Most Effective Shower and Eye Washdown Coverage and Spray Pattern

• Exceeds ANSI/ISEA Z358.1 Specifications

• Exceeds European EN 15154-2 and EN 15154-1

• Industry's Only Self-Draining Design – The Aquaduct™

• Separate Supply and Waste Pipes – Meets CEN and Plumbing Requirements

• Ergonomic Hand Activation Eyewash Paddle – Easy to Reach from Any Direction

• Fully-Assembled and Factory-Tested Eyewash with Hinged Dust Covers

• Universal Identification Sign and Inspection Tag Included

• Classified by Underwriters Laboratories Inc. to ANSI/ISEA Z358.1.

• Listed by Intertek to EN 15154-2 and EN 15154-1

• SpinTec showerheads are covered by one or more of the following patents: 8,113,446;

7,806,348; 8,490,895; D594,089; D669,555; Reg. Comm. Des. D001079560-0001.

Other patents pending.

• Halo is Covered by One or More of the Following Patents: 9,700,484; 9,314,398;

D662220; D673298; D662605; D685920; D662219; and D671228. Other Patents Pending.

Specifications Standard Combination Drench Shower/Eyewash Units save space and fit easily into any work environment. Shower valve operates quickly by a pull rod with a triangular handle.

Shower provides a superior washdown with a more even spray pattern. Halo eyewash, operated by an ergonomic, highly visible push handle or foot pedal, provides effective wash down coverage and spray pattern. Integral strainer reduces debris in the water and also prevents clogging.

This plumbing fixture is not intended to dispense water for human consumption through drinking or for preparation of food or beverages.

Pipe and Fittings Piping to 1-1/4" NPT water supply inlet on unit. Piping to 1-1/4" NPT drain outlet.

1-1/4" piping assembly manufactured of one of the following materials:

• Galvanized steel with BradTect® safety yellow coating

Ball Valve 1" shower ball valve and ½" stay-open eyewash valve manufactured of the following materials and supplied with type 304 stainless steel pull rod and handle:

• Chrome-plated brass

SpinTec™ Showerhead Standard showerhead is 3.1" (78.7mm) diameter highly visible yellow impact-resistant plastic. 10¾" (273mm) diameter corrosion-resistant stainless steel shroud (S19314UU).

SpinTec drench showerhead features integral 22 GPM (83.3 L) flow control (exceeds minimum water flow of 20 GPM (75.7L) at 30 PSI (2.0 bar)), conserving water and helping to accurately size your tepid water system.

SpinTec Flow Rate vs Inlet Pressure at Fixture

10 20 30 40 50 60 70 80 90

Inlet pressure at Fixture (psig)

Fl ow

R at e (g pm

Eyewash The Halo eyewash system offers a high performance rinsing platform that provides rapid relief to an individual’s eyes that have been injured by chemicals or particulate. The eyewash includes an integral 5.1 GPM (19.2 L) flow control, providing water at a safe velocity while maintaining its effectiveness (exceeds minimum water flow of 0.4 GPM (1.5 L) at 30 PSI (2.0 bar)). The eyewash is protected by flip open dust covers that open when the product is activated by Type 304 stainless steel push handle or foot activation by Type 304 stainless steel foot pedal. Safe, steady water flow under varying water supply conditions from 30–90 PSI (2.0-6.1 bar) is assured by integral flow control in the sprayhead assembly. Sprayheads are made from an impact resistant ABS plastic.

Bowl Bowl is constructed of Type 304 corrosion-resistant stainless steel.

For information on all available S19314 models, please see tech data document Bradley_SafetyCombi_S19314Series.

Model Description

S19314LL

Halo eyewash, plastic showerhead, stainless steel bowl, hand/foot activated

S19314UU

Halo eyewash, plastic showerhead w/ stainless steel shroud & bowl, hand/foot operated eyewash

Tepid Water Options

Navigator S19-2100 EFX25 Emergency Thermostatic Mixing Valve

Keltech SNA-Series Tankless Water Heater

Satisfies ANSI/ISEA Z358.1 tepid water requirements.

https://www.bradleycorp.com/thermostatic-mixing-valves/emergency-thermostatic-valves/navigator-efx25 https://www.bradleycorp.com/thermostatic-mixing-valves/emergency-thermostatic-valves/navigator-efx25 https://www.bradleycorp.com/tankless-water-heaters/emergency-safety-shower-tankless-water-heater https://www.bradleycorp.com/tankless-water-heaters/emergency-safety-shower-tankless-water-heater

S19314LL, S19314UU

Combination Drench Shower and Halo™ Eyewash with Foot Pedal

© 2018 Bradley

Page 2 of 2 3/6/2018

Bradley_SafetyCombi_S19314LL_UU

6" (152mm)

62¼" (1581mm) to bottom of base

Ø 3.1" (78.7mm)

941⁄8" (2391mm)

2613⁄16" (681mm)

861⁄8" (2188mm)

923⁄16" (2342mm)

Standard drain outlet

34¾" (883mm) to Bottom of Base

Foot Pedal Activation

All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1⁄8"(3mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints across the length of the dimension and multiply it by 1⁄8" (3mm).

Eyewash Bowl

13" (330mm)

18½" (470mm)

677⁄8" (1724mm)

S19314 shown with Foot Pedal

Stainless Steel Ø 10¾" (273mm)

Plastic Showerhead with Stainless Steel Shroud

TOILET COMPARTMENTS

Section 10 21 13

Date: April 26, 2018

DYESS AIR FORCE BASE – BLDG 8040

TOILET COMPARTMENT CLARIFICATIONS

1. Please note, spec called for all stainless hardware, however 8” wrap around hinges are only available in aluminum to include slide latch. Aluminum hinges/slide latch were schedule and all other accompaning HW is stainless steel. Please advise if change is desired.

2. Please note wall partition dimensions for compartment must be field verified befor compartments are to be ordered. Please coordinate a date for walk through at your earliest convenience.

Dyess Air Force Base - Building 8040

April 26, 2018 Page 1 of 1

2 SOLID PLASTIC ACPA

PARTITIONS

2 URINAL SCREEN SOLID PLASTIC ACPA

2 Install Toilet Partitions INSTALL TOILET PARTITIONS MIHW

HEADING #TA.4 (SET #TA)

1 Other Door #IAP MEN

1 Other Door #IAP WOMEN

TRANSMITTAL

WWW.ACCURATEPARTITIONS.COM

VANITY

8" ALUMINUM

WRAP-AROUND HINGES

6" ALUMINUM

WRAP-AROUND STRIKE

TRIM

SHOES

STAINLESS STEEL

CONTINUOUS BRACKETS (OPTIONAL)

ASI Accurate Partitions 160 Tower Drive Burr Ridge, IL 60527

708.442.6800 (P) • 708.442.7439 (F) www.asi-accuratepartitions.com

WARRANTY

Page 1 of 1 March 2018

ASI Accurate Partitions warrants that its products will be free of defects in material or workmanship under normal usage from the date of invoice for a period as stated below.

Powder Coated Steel: Three (3) years against chipping, flaking, cracking or discoloration

Stainless Steel: Five (5) years against corrosion or discoloration

Moisture Guard™ Plastic Laminate: Five (5) years against discoloration or delamination

Standard Plastic Laminate: Two (2) years against discoloration or delamination

Black Core/Color-Thru Phenolic: Ten (10) years against delamination, breakage or corrosion

Solid Plastic Polymer: Fifteen (15) years against delamination, breakage or corrosion

If material is found to be defective during the above period, the material shall be repaired or replaced (at ASI Accurate Partitions discretion) free of charge. No credits or allowances shall be issued for any labor or expenses relating to the repair replacement of components covered under the warranty plan. The repair or replacement of material shall be the sole remedy of purchaser and Accurate Partitions Corp shall not be liable for incidental, consequential or indirect damages caused by any defects in the partitions or any delay in repairing or replacing defective product.

These warranties shall not be applicable if vandalism, improper installation, or improper cleaning/maintenance of partitions has contributed as just cause for the partition failure. These warranties extend to commercial and industrial purchasers and do not extend to any other persons, including consumers of the partitions. These warranties are in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose or otherwise.

http://www.accuratepartitions.com/

MATERIAL APPROVAL SUBMITTAL

(See Instructions on Reverse)

Form Approved OMB No 9000-0062

Expires May 31, 2005

Public reporting burden for this collection of information is estimated to average 20 minutes per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to the Department of Defense, Washington Headquarters Services, Directorate for Information Operations and

Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project OMB No 9000-0062, Washington DC 20503. Please DO NOT RETURN your form to either of these addresses. Send your completed form to: SAF/AQCP, 1060 Air Force Pentagon, Washington DC

TO: (Contracting Officer) FROM: (Contractor) DATE

CONTRACT NUMBER SUBMISSION NUMBER SUBMITTAL

PREVIOUS SUBMISSION NUMBER PROJECT NUMBER

TO BE COMPLETED BY CONTRACTOR FOR GOVERNMENT USE ONLY

ITEM

NO.

SPECIFICATION SECTION/

PARA NO./DRAWING NO.

DESCRIPTION OF MATERIAL

(Include Type, Model Number, Catalog Number, Mfg., etc.)

AP-

PROVED

DISAP-

SEE

REVERSE

INITIAL

BY COMPLETING THIS FORM, THE UNDERSIGNED CONTRACTOR CERTIFIES THAT

THE MATERIAL COMPLIES WITH ALL SPECIFICATIONS OF SUBJECT CONTRACT.

DATE (YYYYMMDD) TYPE OR PRINT NAME AND GRADE SIGNATURE

FOR GOVERNMENT USE ONLY

TO: (Base Civil Engineering Officer)

For Evaluation and Action RNLT ________________ OR SOONER

TO: (AF Contracting Office)

RECOMMEND APPROVAL DISAPPROVAL AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE

TO: (Contractor)

APPROVED

DISAPROVED AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE SIDE. REQUEST

RESUBMITTAL ON DISAPPROVED ITEMS WITHIN ____ DAYS OF DATE SHOWN BELOW.

AF IMT 3000, 20030901, V1 PREVIOUS EDITION IS OBSOLETE.

New Resubmittal

COMMENTS

(Number to correspond with applicable Item Number on reverse)

INSTRUCTIONS TO CONTRACTORS

1. The term "material" is defined as articles, supplies, raw materials, equipment, parts, components, and end items that are to be incorporated into the work required by the contract.

2. This form is to be used by contractors for submitting Shop Drawings, Equipment Data, Manufacturer's Literature and Certificates and samples of Materials to the Government for approval in accordance with the provisions of this contract. Unless otherwise specified, it is to be prepared in 4 copies, signed, and provided to the contracting officer with appropriate attachments.

3. Item(s) to be approved will be clearly tabbed or identified. Data pertaining to item(s) to be approved will be clearly identified or tabbed, particularly where documents are voluminous, in order to properly evaluate the materials or articles to be incorporated in the work. Each attachment will be numbered to correspond with the item number shown on the face of this form.

4. Requests submitted shall be numbered consecutively, by contract, in the space entitled "Submission No.". This number, in addition to the Contract No., will be used to identify each Material Approval Submittal. Resubmissions will be indicated in the appropriate block and the insertion of previous submission number and data in addition to a new submission number. A single submission should be used for all work of a section of the specifications, but in NO instance should the submission include work for more than one (1) contract. Submittals requiring priority handling will be submitted by separate submittal using the form and so marked across the face of the form.

5. This Material Approval Submittal is not valid unless it is signed by the contracting officer. This approval is required as called for by the contracting officer under the terms of this contract.

AF IMT 3000, 20030901, V1 (REVERSE)

2019-09-23T11:15:10-0500

ROLAN.PATRICK.M.1515150249

TO Contracting Officer: SrA Lydia Simpkins

FROM Contractor: FARR Builders LLC S. Gevers, San Antonio, TX 78210

DATE: 18 Sept. 2019

CONTRACT NUMBER: FA4661-15-D-0001

SUBMISSION NUMBER: 80

PREVIOUS SUBMISSION NUMBER: 79

PROJECT NUMBER: FNWZ 12-0053

ITEM NORow1: 1

SPECIFICATION SECTION PARA NODRAWING NORow1: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow1: Toilet Accessories

INITIALRow1: PR

ITEM NORow2: 2

SPECIFICATION SECTION PARA NODRAWING NORow2: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow2: Toilet Partions

INITIALRow2: PR

ITEM NORow3: 3

SPECIFICATION SECTION PARA NODRAWING NORow3: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow3: Benches

INITIALRow3: PR

ITEM NORow4:

SPECIFICATION SECTION PARA NODRAWING NORow4:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow4:

INITIALRow4:

ITEM NORow5:

SPECIFICATION SECTION PARA NODRAWING NORow5:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow5:

INITIALRow5:

ITEM NORow6:

SPECIFICATION SECTION PARA NODRAWING NORow6:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow6:

INITIALRow6:

ITEM NORow7:

SPECIFICATION SECTION PARA NODRAWING NORow7:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow7:

INITIALRow7:

ITEM NORow8:

SPECIFICATION SECTION PARA NODRAWING NORow8:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow8:

INITIALRow8:

ITEM NORow9:

SPECIFICATION SECTION PARA NODRAWING NORow9:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow9:

INITIALRow9:

ITEM NORow10:

SPECIFICATION SECTION PARA NODRAWING NORow10:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow10:

INITIALRow10:

ITEM NORow11:

SPECIFICATION SECTION PARA NODRAWING NORow11:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow11:

INITIALRow11:

DATE YYYYMMDD: 2019-09-18

TYPE OR PRINT NAME AND GRADE: Wayne Owens, PS

TO Base Civil Engineering Officer: 502 CE

RNLT:

DATE YYYYMMDD_2:

TYPE OR PRINT NAME AND GRADE_2:

TO AF Contracting Office:

DATE YYYYMMDD_3: 20190920

TYPE OR PRINT NAME AND GRADE_3: Patrick Rolan, GS-12

TO Contractor:

DATE YYYYMMDD_4:

TYPE OR PRINT NAME AND GRADE_4:

Text5:

Check Box6: Yes

Check Box7: Off

Check Box8: Off

Check Box9: Yes

Check Box10: Off

Check Box11: Yes

Check Box12: Yes

Check Box13: Off

Check Box14: Yes

Check Box15: Off

Check Box16: Off

Check Box17: Off

Check Box18: Off

Check Box19: Off

Check Box20: Off

Check Box21: Off

Check Box22: Off

Check Box23: Off

Check Box24: Off

Check Box25: Off

Check Box26: Off

Check Box27: Off

Check Box28: Off

Check Box29: Off

Check Box30: Off

Check Box31: Off

Check Box32: Off

Check Box33: Off

Check Box34: Off

Check Box35: Off

Check Box36: Off

Check Box37: Off

Check Box38: Off

Check Box3: Yes

Check Box50: Off

Check Box4: Yes

Check Box5: Off

Check Box39: Off

Check Box40: Off

COMMENTS Number to correspond with applicable Item Number on reverseRow1: Toilet partitions must comply with ABA/ADA guidelines for clearances

Bench color selection: Toffee M227

MATERIAL APPROVAL SUBMITTAL

(See Instructions on Reverse)

Form Approved OMB No 9000-0062

Expires May 31, 2005

Public reporting burden for this collection of information is estimated to average 20 minutes per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to the Department of Defense, Washington Headquarters Services, Directorate for Information Operations and

Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project OMB No 9000-0062, Washington DC 20503. Please DO NOT RETURN your form to either of these addresses. Send your completed form to: SAF/AQCP, 1060 Air Force Pentagon, Washington DC

TO: (Contracting Officer) FROM: (Contractor) DATE

CONTRACT NUMBER SUBMISSION NUMBER SUBMITTAL

PREVIOUS SUBMISSION NUMBER PROJECT NUMBER

TO BE COMPLETED BY CONTRACTOR FOR GOVERNMENT USE ONLY

ITEM

NO.

SPECIFICATION SECTION/

PARA NO./DRAWING NO.

DESCRIPTION OF MATERIAL

(Include Type, Model Number, Catalog Number, Mfg., etc.)

AP-

DISAP-

SEE

REVERSE

INITIAL

BY COMPLETING THIS FORM, THE UNDERSIGNED CONTRACTOR CERTIFIES THAT

THE MATERIAL COMPLIES WITH ALL SPECIFICATIONS OF SUBJECT CONTRACT.

FOR GOVERNMENT USE ONLY

TO: (Base Civil Engineering Officer)

For Evaluation and Action RNLT ________________ OR SOONER

TO: (AF Contracting Office)

RECOMMEND APPROVAL DISAPPROVAL AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE

TO: (Contractor)

APPROVED

DISAPROVED AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE SIDE. REQUEST

RESUBMITTAL ON DISAPPROVED ITEMS WITHIN ____ DAYS OF DATE SHOWN BELOW.

AF IMT 3000, 20030901, V1 PREVIOUS EDITION IS OBSOLETE.

New Resubmittal

COMMENTS

(Number to correspond with applicable Item Number on reverse)

INSTRUCTIONS TO CONTRACTORS

1. The term "material" is defined as articles, supplies, raw materials, equipment, parts, components, and end items that are to be incorporated into the work required by the contract.

2. This form is to be used by contractors for submitting Shop Drawings, Equipment Data, Manufacturer's Literature and Certificates and samples of Materials to the Government for approval in accordance with the provisions of this contract. Unless otherwise specified, it is to be prepared in 4 copies, signed, and provided to the contracting officer with appropriate attachments.

3. Item(s) to be approved will be clearly tabbed or identified. Data pertaining to item(s) to be approved will be clearly identified or tabbed, particularly where documents are voluminous, in order to properly evaluate the materials or articles to be incorporated in the work. Each attachment will be numbered to correspond with the item number shown on the face of this form.

4. Requests submitted shall be numbered consecutively, by contract, in the space entitled "Submission No.". This number, in addition to the Contract No., will be used to identify each Material Approval Submittal. Resubmissions will be indicated in the appropriate block and the insertion of previous submission number and data in addition to a new submission number. A single submission should be used for all work of a section of the specifications, but in NO instance should the submission include work for more than one (1) contract. Submittals requiring priority handling will be submitted by separate submittal using the form and so marked across the face of the form.

5. This Material Approval Submittal is not valid unless it is signed by the contracting officer. This approval is required as called for by the contracting officer under the terms of this contract.

AF IMT 3000, 20030901, V1 (REVERSE)

2019-09-20T14:52:41-0500

ROLAN.PATRICK.M.1515150249

2019-09-20T15:57:43-0500

GARRIGAS.CHRISTA.L.1287173314

TO Contracting Officer: SrA Lydia Simpkins

FROM Contractor: FARR Builders LLC S. Gevers, San Antonio, TX 78210

DATE: 18 Sept. 2019

CONTRACT NUMBER: FA4661-15-D-0001

SUBMISSION NUMBER: 80

PREVIOUS SUBMISSION NUMBER: 79

PROJECT NUMBER: FNWZ 12-0053

ITEM NORow1: 1

SPECIFICATION SECTION PARA NODRAWING NORow1: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow1: Toilet Accessories

INITIALRow1: PR

ITEM NORow2: 2

SPECIFICATION SECTION PARA NODRAWING NORow2: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow2: Toilet Partions

INITIALRow2: PR

ITEM NORow3: 3

SPECIFICATION SECTION PARA NODRAWING NORow3: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow3: Benches

INITIALRow3: PR

ITEM NORow4:

SPECIFICATION SECTION PARA NODRAWING NORow4:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow4:

INITIALRow4:

ITEM NORow5:

SPECIFICATION SECTION PARA NODRAWING NORow5:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow5:

INITIALRow5:

ITEM NORow6:

SPECIFICATION SECTION PARA NODRAWING NORow6:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow6:

INITIALRow6:

ITEM NORow7:

SPECIFICATION SECTION PARA NODRAWING NORow7:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow7:

INITIALRow7:

ITEM NORow8:

SPECIFICATION SECTION PARA NODRAWING NORow8:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow8:

INITIALRow8:

ITEM NORow9:

SPECIFICATION SECTION PARA NODRAWING NORow9:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow9:

INITIALRow9:

ITEM NORow10:

SPECIFICATION SECTION PARA NODRAWING NORow10:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow10:

INITIALRow10:

ITEM NORow11:

SPECIFICATION SECTION PARA NODRAWING NORow11:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow11:

INITIALRow11:

DATE YYYYMMDD: 2019-09-18

TYPE OR PRINT NAME AND GRADE: Wayne Owens, PS

TO Base Civil Engineering Officer: 502 CE

RNLT:

DATE YYYYMMDD_2:

TYPE OR PRINT NAME AND GRADE_2:

TO AF Contracting Office:

DATE YYYYMMDD_3: 20190920

TYPE OR PRINT NAME AND GRADE_3: Patrick Rolan, GS-12

TO Contractor:

DATE YYYYMMDD_4: 20190920

TYPE OR PRINT NAME AND GRADE_4: Mrs. Christa Garrigas, CO

Text5:

Check Box6: Yes

Check Box7: Off

Check Box8: Off

Check Box9: Yes

Check Box10: Yes

Check Box11: Yes

Check Box12: Yes

Check Box13: Yes

Check Box14: Yes

Check Box15: Off

Check Box16: Off

Check Box17: Off

Check Box18: Off

Check Box19: Off

Check Box20: Off

Check Box21: Off

Check Box22: Off

Check Box23: Off

Check Box24: Off

Check Box25: Off

Check Box26: Off

Check Box27: Off

Check Box28: Off

Check Box29: Off

Check Box30: Off

Check Box31: Off

Check Box32: Off

Check Box33: Off

Check Box34: Off

Check Box35: Off

Check Box36: Off

Check Box37: Off

Check Box38: Off

Check Box3: Yes

Check Box50: Off

Check Box4: Yes

Check Box5: Off

Check Box39: Yes

Check Box40: Off

COMMENTS Number to correspond with applicable Item Number on reverseRow1: Toilet partitions must comply with ABA/ADA guidelines for clearances

Bench color selection: Toffee M227