MS 079 Radius Bullnose for Doorways.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

MATERIAL APPROVAL SUBMITTAL

(See Instructions on Reverse)

Form Approved OMB No 9000-0062

Expires May 31, 2005

Public reporting burden for this collection of information is estimated to average 20 minutes per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to the Department of Defense, Washington Headquarters Services, Directorate for Information Operations and

Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project OMB No 9000-0062, Washington DC 20503. Please DO NOT RETURN your form to either of these addresses. Send your completed form to: SAF/AQCP, 1060 Air Force Pentagon, Washington DC

TO: (Contracting Officer) FROM: (Contractor) DATE

CONTRACT NUMBER SUBMISSION NUMBER SUBMITTAL

PREVIOUS SUBMISSION NUMBER PROJECT NUMBER

TO BE COMPLETED BY CONTRACTOR FOR GOVERNMENT USE ONLY

ITEM

NO.

SPECIFICATION SECTION/

PARA NO./DRAWING NO.

DESCRIPTION OF MATERIAL

(Include Type, Model Number, Catalog Number, Mfg., etc.)

AP-

PROVED

DISAP-

PROVED

SEE

REVERSE

INITIAL

BY COMPLETING THIS FORM, THE UNDERSIGNED CONTRACTOR CERTIFIES THAT

THE MATERIAL COMPLIES WITH ALL SPECIFICATIONS OF SUBJECT CONTRACT.

DATE (YYYYMMDD) TYPE OR PRINT NAME AND GRADE SIGNATURE

FOR GOVERNMENT USE ONLY

TO: (Base Civil Engineering Officer)

For Evaluation and Action RNLT ________________ OR SOONER

TO: (AF Contracting Office)

RECOMMEND APPROVAL DISAPPROVAL AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE

TO: (Contractor)

APPROVED

DISAPROVED AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE SIDE. REQUEST

RESUBMITTAL ON DISAPPROVED ITEMS WITHIN ____ DAYS OF DATE SHOWN BELOW.

AF IMT 3000, 20030901, V1 PREVIOUS EDITION IS OBSOLETE.

New Resubmittal

COMMENTS

(Number to correspond with applicable Item Number on reverse)

INSTRUCTIONS TO CONTRACTORS

1. The term "material" is defined as articles, supplies, raw materials, equipment, parts, components, and end items that are to be incorporated into the work required by the contract.

2. This form is to be used by contractors for submitting Shop Drawings, Equipment Data, Manufacturer's Literature and Certificates and samples of Materials to the Government for approval in accordance with the provisions of this contract. Unless otherwise specified, it is to be prepared in 4 copies, signed, and provided to the contracting officer with appropriate attachments.

3. Item(s) to be approved will be clearly tabbed or identified. Data pertaining to item(s) to be approved will be clearly identified or tabbed, particularly where documents are voluminous, in order to properly evaluate the materials or articles to be incorporated in the work. Each attachment will be numbered to correspond with the item number shown on the face of this form.

4. Requests submitted shall be numbered consecutively, by contract, in the space entitled "Submission No.". This number, in addition to the Contract No., will be used to identify each Material Approval Submittal. Resubmissions will be indicated in the appropriate block and the insertion of previous submission number and data in addition to a new submission number. A single submission should be used for all work of a section of the specifications, but in NO instance should the submission include work for more than one (1) contract. Submittals requiring priority handling will be submitted by separate submittal using the form and so marked across the face of the form.

5. This Material Approval Submittal is not valid unless it is signed by the contracting officer. This approval is required as called for by the contracting officer under the terms of this contract.

AF IMT 3000, 20030901, V1 (REVERSE)

2019-09-10T15:12:41-0500

ROLAN.PATRICK.M.1515150249

2019-09-16T11:20:16-0500

GARRIGAS.CHRISTA.L.1287173314

TO Contracting Officer: SrA Lydia SimpkinsWater

FROM Contractor: FARR Builders LLC S. Gevers, San Antonio, TX 78210

DATE: 06 Sept. 2019

CONTRACT NUMBER: FA4661-15-D-0001

SUBMISSION NUMBER: 79

PREVIOUS SUBMISSION NUMBER: 78A

PROJECT NUMBER: FNWZ 12-0053

ITEM NORow1: 1

SPECIFICATION SECTION PARA NODRAWING NORow1: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow1: Radius Bullnose For Doorways

INITIALRow1: PR

ITEM NORow2:

SPECIFICATION SECTION PARA NODRAWING NORow2:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow2: Specifications And Details

INITIALRow2:

ITEM NORow3:

SPECIFICATION SECTION PARA NODRAWING NORow3:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow3:

INITIALRow3:

ITEM NORow4:

SPECIFICATION SECTION PARA NODRAWING NORow4:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow4: Specs 09 30 10, 2.1.1.10.c: requires the use of

INITIALRow4:

ITEM NORow5:

SPECIFICATION SECTION PARA NODRAWING NORow5:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow5: Schluter Systems Rondec at tile outside

INITIALRow5:

ITEM NORow6:

SPECIFICATION SECTION PARA NODRAWING NORow6:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow6: corners such as the wall corners at doorways.

INITIALRow6:

ITEM NORow7:

SPECIFICATION SECTION PARA NODRAWING NORow7:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow7:

INITIALRow7:

ITEM NORow8:

SPECIFICATION SECTION PARA NODRAWING NORow8:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow8:

INITIALRow8:

ITEM NORow9:

SPECIFICATION SECTION PARA NODRAWING NORow9:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow9:

INITIALRow9:

ITEM NORow10:

SPECIFICATION SECTION PARA NODRAWING NORow10:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow10:

INITIALRow10:

ITEM NORow11:

SPECIFICATION SECTION PARA NODRAWING NORow11:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow11:

INITIALRow11:

DATE YYYYMMDD: 2019/09/06

TYPE OR PRINT NAME AND GRADE: Wayne Owens, PS

TO Base Civil Engineering Officer: 502 CE

RNLT:

DATE YYYYMMDD_2:

TYPE OR PRINT NAME AND GRADE_2:

TO AF Contracting Office:

DATE YYYYMMDD_3: 20190910

TYPE OR PRINT NAME AND GRADE_3: Patrick Rolan, GS-12

TO Contractor:

DATE YYYYMMDD_4: 20190910

TYPE OR PRINT NAME AND GRADE_4: Mrs. Christa Garrigas, GS-12

Text5:

Check Box6: Off

Check Box7: Yes

Check Box8: Off

Check Box9: Off

Check Box10: Off

Check Box11: Off

Check Box12: Off

Check Box13: Off

Check Box14: Off

Check Box15: Off

Check Box16: Off

Check Box17: Off

Check Box18: Off

Check Box19: Off

Check Box20: Off

Check Box21: Off

Check Box22: Off

Check Box23: Off

Check Box24: Off

Check Box25: Off

Check Box26: Off

Check Box27: Off

Check Box28: Off

Check Box29: Off

Check Box30: Off

Check Box31: Off

Check Box32: Off

Check Box33: Off

Check Box34: Off

Check Box35: Off

Check Box36: Off

Check Box37: Off

Check Box38: Off

Check Box3: Yes

Check Box50: Off

Check Box4: Off

Check Box5: Yes

Check Box39: Off

Check Box40: Yes

COMMENTS Number to correspond with applicable Item Number on reverseRow1:

WALL

SEMI-GLOSS™ & MATTE™

GLAZED CERAMIC

Cover and above photos feature Semi-Gloss™ Spa 6 x 6 on the wall, Artisan Brown and Almond 1 x 6 and 1/2 x 6 flat liners, and Keystones™ Uptown Taupe and Spa 2 x 2 on the wall.

The Essentials– Redefined

• SUITS MULTIPLE DESIGN NEEDS AND STYLES

- Can be used in a variety of ways, including interior and exterior walls, countertops, and pool linings for both residential and commercial applications

- Offered in two finishes and extensive color palette to suit many design styles

• COORDINATING OPTIONS

- Colors coordinate with Modern Dimensions™ and Rittenhouse Square™ lines, offering more design options

- Coordinating trim available for that finishing touch

Semi-Gloss™ and Matte™ glazed wall tile offers an extensive collection of color options.

This color palette offers a selection that extends from neutral and earthy to bright and trendy. With both matte and semi-gloss surfaces, this line is suitable for both residential and commercial usage including interior and exterior walls, countertops, and pool linings.

From clean neutrals to bright and vibrant colors, you’re sure to find the color you need to create the perfect design color scheme.

POST-CONSUMER

RECYCLED MATERIALS

PRE-CONSUMER

RECYCLED MATERIALS

MADE IN THE U.S.A.

All or select items within this series meet the requirements for these qualifications.

For more information visit daltile.com.USAGE

Floors Walls Countertops

F W C

(1), (2), (3), (4), and (5) indicate price groups, (1) being the least expensive.

✚ “Q” colors are special order. Please allow 1-2 weeks lead time from the date of order.

★ Subject to crazing; black grout not recommended.

◆ Made to order and requires 6-8 weeks delivery from date of order.

See the Rittenhouse Square™ Collection for colors available in 3 x 6 sizes.

See the Modern Dimensions™ Collection for colors available in 4-1/4 x 8-1/2 and 4-1/4 x 12-3/4 sizes.

SEMI-GLOSS WALL TILE

ALMOND

0135 (1)

ARCTIC WHITE

0190 (1)

K165 (2)

WHITE

0100 (1)

URBAN PUTTY

0161 (1)

WHITE

K101 (2)

ARCHITECTURAL

GRAY 0109 (2)

GOLDEN

GRANITE 0138 (1)

UPTOWN TAUPE

0132 (2)

PEPPER WHITE

0147 (1)

ELEMENTAL TAN

0166 (1)

ARTISAN BROWN

0144 (2) ◆

BISCUIT

K175 (2)

CRISP LINEN

0139 (1)

KEY LIME

Q098 (4) ✚

ICE GREY

K176 (2)

DESERT GRAY

X114 (1)

SUEDE GRAY

0182 (2)

PLUM CRAZY

Q178 (4) ✚

CORAL BEAD

Q092 (4) ✚

ORANGE BURST

Q097 (4) ✚

FIRE BRICK

Q093 (4) ✚

CHAMPAGNE

TOAST Q150 (4) ✚

CITRIC BLOOM

Q140 (4) ✚

GO GREEN

Q170 (4) ✚

CHALK BOARD

Q180 (4) ✚

SPA

0148 (1)

AQUA GLOW

0197 (2) ◆

AEGEAN

Q192 (4) ✚

SEA BREEZE

Q174 (4) ✚

ELECTRIC BLUE

Q194 (4) ✚

OCEAN BLUE

Q049 (4) ✚

BLACK

K111 (2)

GARDEN SPOT

0141 (2) ◆

WOOD VIOLET

Q467 (4) ✚

MOON BEAM

Q091 (4) ✚

CORNSILK

0160 (1)

LUMINARY GOLD

0142 (2)

SUNFLOWER

DH50 (3) ◆

MUSTARD

Q012 (4) ✚

TOTALLY TANGERINE

Q151 (4) ✚

CARNATION

PINK Q095 (4) ✚

PUMPKIN SPICE

Q090 (4) ✚

NAVY

K189 (2) ★ ◆

WATERFALL

0169 (1)

COBALT

DM14 (3) ★ ◆

GALAXY

1469 (1) ◆

CHIANTI

Q094 (4) ✚

VERMILLION

0DM1 (5) ★

Kyla

Rectangle

SIZES

Thickness Sq. Ft./ Carton

Pieces/ Carton

6 x 6 Wall Tile

(6" x 6") (15.20 cm x 15.20 cm) 5/16" 12.50 50

4-1/4 x 4-1/4 Wall Tile

(4-1/4" x 4-1/4") (10.80 cm x 10.80 cm) 5/16" 12.50 100

INSTALLATION

Grout Joint Recommendation Shade Variation

1/16" Low (V1)

PERFORMANCE CHARACTERISTICS

ASTM# Result

Water Absorption C373 < 20.0%

Breaking Strength C648 120-230 lbs

Scratch Hardness MOHS 4.0-6.0

Chemical Resistance C650 Resistant

Abrasion Resistance C1027 N/A

For additional information on test results, visit us at:

daltile.com/information/TestResults.

NOTES

Since there are variations in all fired ceramic and natural products, tile and trim supplied for your particular installation may not match samples. Final confirmation should be made from actual tiles and trim prior to installation. Manufactured in accordance with ANSI A137.1 standards.

For additional information refer to “Factors to Consider” at: daltile.com/Factors.

APPLICATIONS

Target DCOF wet Suitable

Dry & Level – Interior Floor N/A

Wet & Level – Interior Floor ≥ 0.42

Shower Floors (Residential or Light Commercial) ≥ 0.42

Exterior Floor Applications (including pool decking & other wet areas with minimal footwear)

≥ 0.60

Ramps & Inclines ≥ 0.65

Walls/Backsplashes N/A

Countertops N/A *

Pool Linings N/A **

A DCOF value of ≥ 0.42 is the standard for tiles specified for level interior spaces expected to be walked upon when wet, as stated in ANSI A137.1-2012, Section 9.6.

For more information about DCOF and the DCOF AcuTest™, visit daltile.com/DCOF.

APPLICATION NOTES :

Suitable for exterior applications in non-freezing climates, when proper installation methods are followed.

* 3 x 6, 4-1/4 x 4-1/4 and 6 x 6 wall tile in matte colors only. Darker colors may show scratches.

** 3 x 6, 4-1/4 x 4-1/4 and 6 x 6 wall tile only

MATTE WALL TILE

ARCTIC

WHITE 0790 (1)

ARTISAN

BROWN 0744 (2) ◆

PEARL

WHITE 0799 (1)

BISCUIT

K775 (2)

DESERT

GRAY X714 (1)

ARCHITECTURAL

GRAY 0709 (2)

BLACK

K711 (2)

X735 (1)

URBAN

PUTTY 0761 (1)

UPTOWN

TAUPE 0732 (2)

ELEMENTAL

TAN 0766 (1)

(1) and (2) indicate price groups, (1) being the least expensive.

◆ Made to order and requires 6-8 weeks delivery from date of order.

See the Rittenhouse Square™ Collection for colors available in 3 x 6 sizes.

See the Modern Dimensions™ Collection for colors available in 4-1/4 x 8-1/2 and 4-1/4 x 12-3/4 sizes.

DESIGNED TO HELP EARN LEED™ CREDITS. For more detailed information, visit daltilegreenworks.com.

7834 C.F. Hawn Freeway, Dallas, Texas 75217 | 1.800.933.TILE

To view the complete collection of Daltile® products and information, visit our website at daltile.com. ©2018 Daltile (3/18)

TRIM

Type Number Size Pieces/ Carton Semi-Gloss Matte

Bullnose** p S-4269 2 x 6 100 Groups 1, 2, 3, 4, 5 Groups 1, 2

Bullnose** S-4449 4-1/4 x 4-1/4 100 Groups 1, 2, 3, 4, 5 Groups 1, 2

Bullnose** S-4669 6 x 6 50 Groups 1, 2, 4, 5 Groups 1, 2

Bullnose Corner** t i SN-4269 2 x 2 25 Groups 1, 2, 3, 4 Groups 1, 2

Bullnose Corner** v i SCRL-4449 4-1/4 x 4-1/4 100 Groups 1, 2, 3, 4 Groups 1, 2

Bullnose Corner** v i SCRL-4669 6 x 6 50 Groups 1, 2, 4 Groups 1, 2

Radius Bullnose w p A-4200 2 x 6 100 Groups 1, 2, 3, 4 Groups 1, 2

Radius Bullnose Corner w t AN-4200 2 x 2 20 Groups 1, 2, 3, 4 Groups 1, 2

Radius Bullnose ◆ A-4402 4-1/4 x 4 1/4 84 Groups 1, 4 --

Radius Bullnose Corner ◆ ACRL-4402 4-1/4 x 4 1/4 30 Groups 1, 4 --

Radius Bullnose ◆ A-3602 6 x 6 44 Group 1 --

Radius Bullnose Corner Left or Right ◆ ACR-L-3602 6 x 6 20 Group 1 --

Flat Top Cove* A-3401 4-1/4 x 4-1/4 84 Groups 1, 2, 4 Groups 1, 2

Flat Top Cove* w t A-3601 6 x 6 44 Groups 1, 2, 4 Groups 1, 2

Flat Top Cove* w A-3461 4-1/4 x 6 60 Group 1 Group 1

Flat Top Cove Corner Left or Right* v i

SCR-L-3401 4-1/4 x 4-1/4 30 Groups 1, 2, 4 Group 1

Flat Top Cove Radius Corner Left or Right* ACR-L-3401 4-1/4 x 4-1/4 30 Group 4 --

Flat Top Cove Corner Left or Right * n l w t

SCR-L-3601 6 x 6 20 Groups 1, 2, 4 Groups 1, 2

Sanitary Cove Base s w t S-3419T 4-1/4 x 6 60 Groups 1, 2, 4 Groups 1, 2

Sanitary Cove Base s w S-3619T 6 x 6 40 Groups 1, 4 Group 1

Sanitary Cove Base Corner Left or Right s w t

SCR-L-3419T 4-1/4 x 6 20 Groups 1, 2, 4 Groups 1, 2

Sanitary Cove Base Corner Left or Right s w

SCR-L-3619T 6 x 6 20 Groups 1, 4 Group 1

Quarter Round w t A-106 3/4 x 6 152 Groups 1, 2, 4 Groups 1, 2

Quarter Round Beak w t AC-106 3/4 x 6 120 Groups 1, 2, 4 Groups 1, 2

Sink Rail ◆ W-8262 2-1/2 x 2 x 6 66 Group 1 --

Sink Rail Outside Corner* ◆ WAC-8262 2-1/2 x 2 x 2 40/20 Group 1 --

Sink Rail Inside Corner/V- Cap * ◆ WAM-8262 2 x 2 x 2-1/2 66 Group 1 --

Shower Jam/Curb* ◆ A-7250 2-1/2 x 6 60 Group 1 --

All colors available (except Vermillion 0DM1) through Special Order.

w Group 1 colors only available in 0100, 0135, 0161, 0190, 0761, 0790, X114, X714, X735 and special order colors are 0138, 0147, 0166, 0766, 0799.

All other colors are made-to-order.

p Group 2 colors are only available in 0142,0182, 0197, K101,K111, K165, K175, K176, K189, K711, K775 t Group 2 colors are made-to-order and only available in

0142,0182, 0197, K101, K111, K165, K175, K176, K189, K711, K775

◆ Group 1 colors only available in 0100, 0135 and 0190

** For thinset bed installation i Group 1 colors all available and made-to-order colors are

0138, 0139, 0147, 0148, 0160, 0166, 0169, 0766, 0799 & 1469 v Group 2 colors are made-to-order

* For conventional mortar installation n Not available in colors 0109, 0139, 0141, 0144, 0148, 0160, 0169, 0709, 0744, I469 l Not available in 0132 and 0732 s Roundtop

SURFACE TRIM

4-1/4 x 4-1/4 typical installation

* Opposite not shown

CONVENTIONAL TRIM

4-1/4 x 4-1/4 typical installation

* Opposite not shown

Kyla

Rectangle

Date SDS Prepared: May 31, 2015 Page 1 of 5

1. PRODUCT IDENTIFICATION

Common Name:

Synonyms: Ceramic Tile and Wares

Manufacturer Name: Dal-Tile Corporation

Address: Headquarters Office

7834 C.F. Hawn Freeway, Dallas, TX 75217

Emergency Assistance: Environmental, Health and Safety Department

Richard Ray - (214) 309-4295

1-800-933-TILE; (214) 398-1411 (24-hour number)

Recommended Use:

2. HAZARDS IDENTIFICATION

Emergency Overview: Danger! Lung injury and Cancer Hazard

GHS Classification (Global Harmonized Standard Classification):

Carcinogenicity Category 1A (H350)

Specific target organ toxicity, single exposure; Respiratory tract irritation - Category 3 (H335)

Specific target organ toxicity, repeated exposure - Category 1A (H372)

GHS Label, Hazards and Precautionary Statements

GHS Pictogram:

Crystalline Silica: Category 3 (Respiratory tract irritation) (H335)

Categories 1A(Carcinogenicity)(H372)

Label Signal Word: Danger

Hazard Statements:

(H350) May cause CANCER (inhalation)

(H335) May cause respiratory irritation

(H372) Causes damage to organs (lung/respiratory) through prolonged or repeated exposure (inhalation)

May contain Recycled and/or Reclaimed Materials www.daltile.com/leed

SAFETY DATA SHEET

CERAMIC TILE

Ceramic Tile (For purposes of this SDS, the term “ceramic” encompasses all types of tile products manufactured/sourced by Dal-Tile Corporation.)

Tile Series: Semi-Gloss

Building Material - Tile products manufactured/sourced by Dal-Tile Corporation are environmentally preferable building materials when compared to other floor/wall coverings. As defined by guidelines issued by the Environmental Protection Agency, the American Society for

Testing & Materials, and the Federal Trade Commission, Tile is one of the most environmentally friendly building materials you can buy today. Should you desire additional information, please direct your inquiry to the address above.

Tile products are mixtures of predominantly clays, silica sand, and other natural occurring minerals that have been mixed with water and fired in a high temperature kiln. The finished, fired tiles are odorless, stable, non-flammable, and pose no immediate hazard to health.

Respiratory, hand and eye protection may be needed to prevent excess exposure to airborne particulates if dust is produced by cutting tiles during installation or if dust is produced by any other operations, including demolition/removal projects.

This document has been prepared in accordance with the Occupational Safety and Health Administration (OSHA) Hazard

Communication standard, 29 Code of Federal Regulations (CFR) 1910.1200(g), Safety Data Sheets.

http://www.daltile.com/leed

Date SDS Prepared: May 31, 2015 Page 2 of 5

2. HAZARDS IDENTIFICATION (CONT)

Precautionary Statements:

Do not handle until all safety precautions have been read and understood. (P202)

Do not breathe dust/spray. (P260 + P261)

Wash skin thoroughly after handling. (P264)

Do not eat, drink or smoke when using this product. (P270)

Wear protective gloves, protective clothing, eye protection, face protection. (P280)

Potential Health Effects:

Inhalation: Do not breathe dust. See “Health Hazards” in Section 11 for more details.

3. COMPOSITION/INFORMATION ON INGREDIENTS

Tiles are manufactured in various shapes, sizes, and colors.

These products do not contain asbestos.

Composition EU Class

Crystalline silica as quartz CAS: 14808-60-7 (67/548/EEC)

EINECS: 238-878-4 Xn R48/20

Clays CAS: 1332-58-7 (67/548/EEC)

EINECS: 265-064-6 Xi R36/37/38

Nepheline syenite CAS: 37244-96-5 (67/548/EEC)

EINECS: N/A Xi R36/37/38

Talc CAS: 14807-96-6 (67/548/EEC)

EINECS: 238-877-9 Xi R36/37/38

Feldspar CAS: 68476-25-5 (67/548/EEC)

EINECS: 270-666-7 Xi R36/37/38

Biotite CAS: 12001-26-2 (67/548/EEC)

EINECS: 215-479-3 Xi R36/37/38

4. FIRST AID MEASURES

Eyes:

Skin: Wash thoroughly after working with tiles.

Inhalation:

Ingestion: Not applicable for intact tiles.

Have emergency eyewash station available in area where tiles are cut.

5. FIRE-FIGHTING MEASURES AND INFORMATION

Flash Point (Method Used): Not applicable

Autoignition Temperature: Not applicable

Flammable Limits (% by Volume in Air): LEL - not applicable

UEL - not applicable

Fire Extinguishing Media: None required Non-flammable

Special Fire Fighting Procedures: None required

Fire and Explosion Hazards: None

0-15

0-5

Immediately flush eyes with large amounts of water for at least 15 minutes if dust gets in eyes. Get medical attention if irritation persists.

Remove to fresh air if exposed to large amounts of tile dust. Administer artificial respiration if breathing has stopped. Keep victim at rest. Call for prompt medical attention.

Estimated % by Wt.

0-30

CAS# /

EINECS#

0-40

0-50

20-55

Tile products are mixtures of predominately Clays, Silica Sand and other naturally-occurring minerals, that have been mixed with water and fired in a high temperature kiln.

Under normal conditions these products do not release hazardous materials after installation and are not considered hazardous waste should disposal be necessary.

Date SDS Prepared: May 31, 2015 Page 3 of 5

6. ACCIDENTAL RELEASE MEASURES

7. HANDLING AND STORAGE

Do not store near acids. If tiles contact some acids, damage/discoloration to the surface may occur.

Shelf life is unlimited.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

8.1 Exposure Table

Composition

NIOSH

IDLH

Units

Crystalline silica as quartz 0.05 mg/m3

-respirable fraction

-total dust N.E. mg/m3

Clays

-respirable fraction N.E. mg/m3

-total dust** N.E. mg/m3

Nepheline syenite

-respirable fraction** N.E. mg/m3

Talc

-respirable fraction 2 mg/m3

-total dust** 10 mg/m3

Feldspar

-respirable fraction N.E. mg/m3

Biotite

-respirable fraction** 15 mg/m3

* 2006 Edition, respirable fraction to be determined as per Appendix D of ACGIH TLV.

** Covered as particles not otherwise regulated per OSHA and particles not otherwise classified per ACGIH.

N.D. - Not determined

N.E. - Not established

8.2 EXPOSURE CONTROLS/PERSONAL PROTECTION

N.E.

15 N.E.

15 10

N.E N.E.

15 N.E.

2 2

ACGIH

TLV*

Avoid creating excessive dust. Clean up dust with a vacuum system with a High-efficiency particulate (HEPA) air filter vacuum or damp sweeping. See Section 8 of this SDS concerning PPE information for clean-up.

When cutting, grinding or removing, use equipment with integral dust collection and/or use local exhaust ventilation. Use wet cutting methods to reduce generation of dust. Use respiratory protection in the absence of effective engineering controls.

OSHA

PEL

5 N.E.

%SiO2+2

%SiO2+2

0.025

N.E.

Ventilation: Use adequate ventilation to keep exposure to dust below recommended exposure levels. Avoid inhalation of dust. The highest probability of silica exposure occurs during installation using dry cutting methods or during removal of installed tile. Wet cutting methods are recommended.

Respiratory Protection: Use of a properly fitted NIOSH/MSHA approved particulate respirator is recommended when cutting tiles for installation or during the removal of installed tile.

Eye Protection: Use dust-proof goggles or safety glasses with side shields. Contact lenses may absorb irritants. Do not wear contact lenses in work areas.

Skin Protection: Cotton or leather work gloves should be worn when cutting this product to minimize skin exposure to dust and/or cuts. Wash hands prior to eating, drinking, or smoking, and at the end of the work shift, after cutting operations are conducted.

NOTE: Personal protection information in Section 8 is based on general information for normal uses and conditions. Where special or unusual uses or conditions exist, it is suggested that the assistance of an industrial hygienist or other qualified professional be obtained.

Date SDS Prepared: May 31, 2015 Page 4 of 5

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance: Brittle solid; color may vary

Odor: Odorless

Melting Point: Not Available (>2200 F)

Boiling Point: Not applicable

Vapor Pressure: Not applicable

Vapor Density (Air = 1): Not applicable

Solubility in Water: Insoluble

Specific Gravity (H2) = 1): 1.6 to 2.1

Percent Volatile by Volume: Not applicable

Evaporation Rate (Ethyl Ether = 1): Not applicable

Viscosity: Not applicable

Volatility: 0 g/L Volatile Organic Compounds (VOCs)

10. STABILITY AND REACTIVITY

Stability: Stable in current form.

Conditions to Avoid: Avoid contact with acids (e.g., acetic, hydrofluoric, etc.)

Incompatibility (Materials to Avoid): Avoid contact with acids (e.g., acetic, hydrofluoric, etc.)

Hazardous Polymerization: Will not occur.

Hazardous Decomposition Products: None.

11. TOXICOLOGICAL INFORMATION

Potential Health Effects

Primary Routes of Exposure

Acute Effects

Chronic Effects

Potential Adverse Interactions

Carcinogen Status

Overview of Animal Testing

Oral (silica) Lethality

LD50 Rat oral >22,500 mg/kg

LD50 Mouse oral >15,000 mg/kg

LC50 Carp >10,000 mg/l (per 72 hr.)

No acute effects from exposure to intact tile are known. Working with broken or cut tile produces a potential for cuts to the hands and exposed body parts. Acute effects such as eye irritation may occur if associated with high dust operations such as dry cutting tile or during the removal of installed tile. In very rare cases, symptoms of acute silicosis, a form of silicosis (a nodular pulmonary fibrosis) associated with exposure to respirable crystalline silica, may develop following acute exposure to extremely dusty environments caused by generation of tile dust. Signs such as labored breathing and early fatigue may indicate silicosis; however, these same symptoms can arise from many other causes.

No chronic effects are known for exposure to intact tile. Long-term, continual exposure to respirable crystalline silica at or above established permissible occupational exposure limits may lead to the development of silicosis, a nodular pulmonary fibrosis (NPF). NPFs are also associated with pulmonary tuberculosis, bronchitis, emphysema, and other airway diseases. This type of chronic exposure to silica dust may also result in the development of autoimmune disorders, chronic renal disease, and other adverse health effects.

Recent epidemiologic studies demonstrate that workers exposed to elevated silica concentrations have a significant risk of developing chronic silicosis. Signs such as labored breathing and early fatigue may indicate silicosis; however, these same symptoms can also arise from many other causes.

Silicosis may be complicated by severe mycobacterial or fungal infections and result in tuberculosis (TB). Epidemiologic studies have established that silicosis is a risk factor for developing TB. Any existing respiratory or pulmonary diseases may be complicated by exposure to respirable crystalline silica. Smoking may increase the risk of adverse effects if done in conjunction with occupational exposure to silica dust at or above permissible exposure limits.

Respirable crystalline silica is classified by the International Agency for Research on Cancer (IRAC) as a Group I Carcinogen

(carcinogenic to humans). The National Toxicology Program (9th Report) lists respirable crystalline silica as “Known to be a Human

Carcinogen”. USDOL/OSHA and NIOSH have recommended that crystalline silica be considered a potential occupational carcinogen.

Short term experimental studies of rats have found that intratracheal instillation of quartz particles leads to the formation of discrete silicotic nodules in rats, mice and hamsters.

None for intact tile. Inhalation and potential exposure to eyes, hands, or other body parts if contact is made with broken tile, and/or during procedures involving the cutting of tiles, and/or for operations involving the removal of installed tiles.

Date SDS Prepared: May 31, 2015 Page 5 of 5

12. ECOLOGICAL INFORMATION

No information available at this time.

13. DISPOSAL CONSIDERATIONS

14. TRANSPORTATION INFORMATION

D.O.T Shipping Name: Not applicable

Hazard Class: Non-regulated (for disposal purposes material is non-hazardous Class III regulated material)

ID Number: Not applicable

Marking: Not applicable

Label: None

Placard: None

Hazardous Substance/RQ: Not applicable

Shipping Description: Porcelain/Ceramic Tiles

Packaging References: None

15. REGULATORY INFORMATION

Combustible Liquid Flammable Aerosol Oxidizer

Compressed Gas Explosive Pyrophoric

Flammable Gas X Health Hazard (Sections 3 & 11) Unstable

Flammable Liquid Organic Peroxide Water Reactive

Flammable Solid

16. ADDITIONAL INFORMATION

Global Harmonization Identification System

GHIS: Health: 3 Fire: 4 Reactivity: 4

Hazardous Material Identification System

HMIS: Health: 0 Fire: 0 Reactivity: 0

National Fire Protection Association

NFPA: Health: 0 Fire: 0 Reactivity: 0

Note: The information in this data sheet provides information related to the potential hazards associated with dusts which may be produced during cutting or otherwise changing the shape of the tile during installation and/or removal.

Based on information presently available, this product does not meet any of the hazard definitions of 29 CFR Section 1910.1200.

Waste should be disposed of in a landfill certified to accept such materials in accordance with federal, state, and local regulations.

Title 22 Division 2, California Code of Regulation Chapter 3 (Proposition 65): This product contains a chemical or chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

This product and/or its components have been previously introduced into U.S. commerce and is listed in the Toxic Substances Control

Act (TSCA) Inventory of Chemicals in Commerce. Hence, it is subject to all applicable provisions and restrictions under TSCA 40 CFR

Section 721 and 723.250.

This tile contains <1 percent by weight each of the following elements, which are SARA 313 Recordable: Antimony, Arsenic, Barium, Beryllium, Cadmium, Cobalt, Chromium, Copper, Manganese, Mercury, Nickel, Lead, Silver, Thallium, Tin, Titanium, Vanadium, and

Zinc.

This product or its components meets the following hazard definition(s) as defined by the Occupational Safety and Health Hazard

Communication Standard (29 CFR Section 1910.1200):