MS 080 Signage.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

SIGNAGE

A8054

PROJECT: Dyess Air Force Base - Building 8040 Repair Maintenance Shop

1081 2nd Street

Dyess AFB, TX

79607

CONTRACTOR: Farr Builders, LLC 3401 S. Gevers Ste. 1

San Antonio, TX

78210

ARCHITECT: Castillo Architects 981 Southpark Dr

Littleton, CO

Prepared By: Tex-Oma Builders Supply Co.

2701 Commerce Street

Wichita Falls, Texas 76301

Date: August 12, 2019

Dyess Air Force Base - Building 8040

A8054

SIGNAGE CLARIFICATIONS

1. Verify all signage lettering, sizes, and finish before fabrication begins.

2. Submittal contingent on approved change order.

Mounting: BM-3, BOTTOM BAR MOUNT

WITH CUSTOM ANGLE BRACKET

Font: ARCHITECTURAL PRISMATIC

Mounting: BM-3, BOTTOM BAR MOUNT

WITH CUSTOM ANGLE BRACKET

PM-1B MOUNT DETAIL

LETTERS INSTALLED

WITH THREADED

STUDS SET WITH

ADHESIVE...SUITABLE

FOR MOST SOLID

SURFACES (PROJECTED

WITHOUT COLLARS)

10” BOTTOM

STUD MOUNT

3” STUD

SET IN

STUD SUPPORT

RECESSED ½”

BELOW RETURN

TYPICAL FABRICATED ALUMINUM

LETTER WITH BOTTOM

CHANNEL MOUNTING.

BOTTOM REINFORCED

FOR STABILITY.

PM-1 MOUNT DETAIL

WITH THREADED

STUDS SET WITH

ADHESIVE...SUITABLE

FOR MOST SOLID

SURFACES

(PROJECTED

WITH COLLARS)

PM-2 MOUNT DETAIL

PROJECTED MOUNT WITH

BRACKETS (MINIMUM

2” PROJECTION

FM-4 MOUNT DETAIL

WITH THREADED

STUDS SET WITH

ADHESIVE...SUITABLE

FOR MOST SOLID

SURFACES

BOLT

FABRICATED

PANEL

WASHER

ATTACHED

PANEL

80 Red Lion Road Philadelphia, PA 19115

LETTER SPECIFICATIONS:

Material: ALUMINUM

Height:

Depth:

Template: YES Adhesive: YES

I approve this drawing as submitted, no changes I approve this drawing with my changes clearly noted I do not approve this drawing please resubmit

Font: HELVETICA BOLD/MEDIUM Finish: F-4, CLEAR ANODIZED

ELEVATION: 3/4” = 1’

10’ 8” APPROX.

LINE LENGTH

Mounting: FM-4, FLUSH MOUNTING

CLIENT:

S.O#:

P.O#:

DATED:

1868F19

A8054-BL

JULY 22, 2019

TEX-OMA BUILDERS

NOTE; LETTER SIZE INDICATED APPLIES TO LETTERS WITH FLAT TOP/BOTTOMS,

ROUNDED LETTERS, GENERALLY WILL EXCEED THE INDICATED LETTER HEIGHT.

ADDITIONALLY, SELECT FONTS WILL HAVE LOWER CASE TEXT THAT EXCEED

INDICATED HEIGHT. SCRIPT FONT WILL ALWAYS EXCEED HEIGHT .

12” 1” 6” 1/2”

Mounting: PM-1, 1/2” PROJECTED MOUNTING

Mounting: PM-1, PROJECTED MOUNTING

PLEASE SPECIFY PROJECTION

Mounting: PM-1, 1/2” PROJECTED MOUNTING

HELV. MED

HELV. BOLD

SIGN SPECIFICATIONS

IM Series (Square) Mounting: Vinyl Tape (VT)

Holder:

Part Code: SH-88 Part Color: A44 Architectural Brown

Insert:

Part Code: SI/SL-88 Part Color: Clear

Part Code: ADA-DPT

Direct Print Tactile Graphics:

Copy: HelveticaNeue-Regular (HR) Size: 1-1/2” Color: A01 White (Braille Color: Same as backgrd.)

Part Code: SWS-88 (Paper Insert) Paper Color: A00 White

Laser Printed Graphics:

Size: 3/8“ Color: A02 Black

Project:

Sales Rep:

Work Order #: TBD

Approved By:

Approved Date:

Office ID IM Series

A House Kathi MilesCSR/PM: 1/2" = 1"

Draft 23, July 2019 J. GrayDyess AFB Repair Maintenance Shop Bldg 8040

- Tex-Oma Builders Supply

Colors depicted are a general representation of the color specified.

If color selection is critical, please request sample for approval.

8”

3”

33331-1/2"

Name To Be Determined

Size: 1-1/2” Color: A01 White (Braille Color: Same as backgrd.)

Size: 1“

Room ID

B

323232321-1/2"

Paint Mix Room

1"

Size: 5/8” Color: A01 White (Braille Color: Same as backgrd.)

Symbol: S59 (Women/Accessible) Size: 3-3/4“

Locker Room ID

C

5/8"

3-3/4"

WOMEN’SWOMEN’SWOMEN’SWOMEN’S

LOCKERSLOCKERSLOCKERSLOCKERS

3/8"

5/8"

1/4"

A63

DWO3

OAK

DWM1

MAPLE

DWM5

MAHOGANY

DWW2

WALNUT

Background Colors Painting is APCO’s primary process for background color application, and the colors on this page represent the standard options available. PMS colors and custom matched colors are also available upon request.

Imprint Colors APCO’s primary printing process is direct-print, with the ability to print not only these standard colors but also a wide range of PMS colors.1

APCO uses the silkscreen printing process (spot colors) for printing most raised ADA graphics and for other specialty projects. The colors on this page represent the standard silkscreen ink options, but custom color matches are possible.

Paper Colors Colors marked with a P are available in 60 lb. SignWord paper, compatible with most APCO interior systems. (Note: APCO’s Elevate system only offers the A72/A01 White option.)

Addt’l SignWord Paper Colors The reverse sides of A43 Putty and A78 Pearl Grey papers feature a 50% lighter version of the standard paper color, A94 Sand (reverse side of A43) and A98 Pearl Grey Light (reverse side of A78). These lighter versions may represent better matches to painted or injection molded parts. Your APCO Representative can provide guidance in this area.

Color Accuracy & Variations Colors within this chart have been reproduced as accurately as possible. However, colors will vary slightly amongst the different processes, and actual colors may vary from this chart because of individual printer and monitor characteristics.

Important! If color accuracy is important for your project, we recommend you request actual color samples representing the materials and processes being used.

1 There are some color limitations of the CMYK color gamut vs Pantone solid colors, especially with Reflex blues and very bright colors. There are limitations with metallics as well. Your APCO Representative can discuss in more detail.

ELEMENTS

Naturals Application/Process:

Pressure Sensitive Decorative Vinyl.

Primarily clad to non-glare lenses of the FullView and Arcadia systems or to aluminum bands of the Accord 15 system. Can also be simulated with Direct-Print.

F15

WHEAT STRAND

F14

SEAGRASS STRAND

F13

FALLEN LEAVES

F11

BURNISHED GLAZE

W09

GREEN TIGRIS

Natural Patterns / Fibers Application/Process:

Laminate. Primarily used for decorative backers. Can also be simulated with Direct-Print.

F01

AMBER MAPLE

W02

MONTICELLO MAPLE

F02

CHERRY BIRCH

F03

COGNAC MAPLE

W01

MONTANA WALNUT

F04

VICTORIAN MAHOGANY

ELEMENTS 2

Wood Grains Application/Process:

Laminate. Primarily used for simulated with Direct-Print.

DECORATIVE FINISHESBACKGROUND & IMPRINT COLORS

Translucent Acrylics. Used as translucent backer material for all APCO interior systems.

ACF

FROST

L02

COASTAL GRASS

L04

NATURAL LEAVES

DMS4

DIMPLES

DMP3

MICROPERF

DMP2

CAPSULES

Industrials

Decorative Metal. Primarily used as inserts within the Arcadia and FullView systems or within the InsertSlot bands of the Accord 15 system.

DMP1

SQUARES

W05

GREY STONE

W06

MYSTIQUE DUSK

W08

SANDY TOPAZ

W04

ANTIQUE TOPAZ

Stone/Granite/Marble

Laminate. Primarily used for simulated with Direct-Print. F09

UBATUBA GRANITE

F07

JAMOCHA GRANITE

F08

LABRADOR GRANITE

W07

MYSTIQUE NIGHT

F06

COLORADO SLATE

DWC4

CHERRY

A02

BLACK

A81

CINNAMON

A48

CHOCOLATE

A97

CHAMPAGNE METALLIC

A99

BRONZE METALLIC

A43

PUTTY

A72

BONE WHITE

A46

OFF WHITE

A76

BISCUIT

A78

PEARL GREY

A60

BUFF

A01

WHITE

A54

GRAPHITE

A89

SATIN SILVER

A90

MOTH

A75

APRICOT

A64

JADE BLUE

A53

THISTLE GREEN

A83

APPLE GREEN

A52

EMERALD GREEN

A27

DEEP GREEN

A96

OLIVE GREEN

A22

CHROME YELLOW

A67

BRICK RED

A74

INDY BLUE

A95

EGGPLANT

A85

DEEP PURPLE

A88

ROYAL BLUE

A11

COBALT BLUE

A28

ORBIT BLUE

A50

WINDSOR BLUE

A12

PEACOCK BLUE

A86

MINT GREEN

A63

WEDGEWOOD BLUE

A44

ARCHITECTURAL BROWN

A69

AMERICAN RED

A24

WINE

A31

GRAPE

A61

RAISIN

A71

HARVARD GREEN

A14

MEDIUM GREY

A47

LIGHT GREY

A03

WARM GREY

A80

TANGERINE

A08

FIRE RED

A51

DEEP RED

MATERIAL APPROVAL SUBMITTAL

(See Instructions on Reverse)

Form Approved OMB No 9000-0062

Expires May 31, 2005

Public reporting burden for this collection of information is estimated to average 20 minutes per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to the Department of Defense, Washington Headquarters Services, Directorate for Information Operations and

Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project OMB No 9000-0062, Washington DC 20503. Please DO NOT RETURN your form to either of these addresses. Send your completed form to: SAF/AQCP, 1060 Air Force Pentagon, Washington DC

TO: (Contracting Officer) FROM: (Contractor) DATE

CONTRACT NUMBER SUBMISSION NUMBER SUBMITTAL

PREVIOUS SUBMISSION NUMBER PROJECT NUMBER

TO BE COMPLETED BY CONTRACTOR FOR GOVERNMENT USE ONLY

ITEM

NO.

SPECIFICATION SECTION/

PARA NO./DRAWING NO.

DESCRIPTION OF MATERIAL

(Include Type, Model Number, Catalog Number, Mfg., etc.)

AP-

PROVED

DISAP-

PROVED

SEE

REVERSE

INITIAL

BY COMPLETING THIS FORM, THE UNDERSIGNED CONTRACTOR CERTIFIES THAT

THE MATERIAL COMPLIES WITH ALL SPECIFICATIONS OF SUBJECT CONTRACT.

DATE (YYYYMMDD) TYPE OR PRINT NAME AND GRADE SIGNATURE

FOR GOVERNMENT USE ONLY

TO: (Base Civil Engineering Officer)

For Evaluation and Action RNLT ________________ OR SOONER

TO: (AF Contracting Office)

RECOMMEND APPROVAL DISAPPROVAL AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE

TO: (Contractor)

APPROVED

DISAPROVED AS INDICATED ABOVE AND SUBJECT TO ANY APPLICABLE COMMENTS ON THE REVERSE SIDE. REQUEST

RESUBMITTAL ON DISAPPROVED ITEMS WITHIN ____ DAYS OF DATE SHOWN BELOW.

AF IMT 3000, 20030901, V1 PREVIOUS EDITION IS OBSOLETE.

New Resubmittal

COMMENTS

(Number to correspond with applicable Item Number on reverse)

INSTRUCTIONS TO CONTRACTORS

1. The term "material" is defined as articles, supplies, raw materials, equipment, parts, components, and end items that are to be incorporated into the work required by the contract.

2. This form is to be used by contractors for submitting Shop Drawings, Equipment Data, Manufacturer's Literature and Certificates and samples of Materials to the Government for approval in accordance with the provisions of this contract. Unless otherwise specified, it is to be prepared in 4 copies, signed, and provided to the contracting officer with appropriate attachments.

3. Item(s) to be approved will be clearly tabbed or identified. Data pertaining to item(s) to be approved will be clearly identified or tabbed, particularly where documents are voluminous, in order to properly evaluate the materials or articles to be incorporated in the work. Each attachment will be numbered to correspond with the item number shown on the face of this form.

4. Requests submitted shall be numbered consecutively, by contract, in the space entitled "Submission No.". This number, in addition to the Contract No., will be used to identify each Material Approval Submittal. Resubmissions will be indicated in the appropriate block and the insertion of previous submission number and data in addition to a new submission number. A single submission should be used for all work of a section of the specifications, but in NO instance should the submission include work for more than one (1) contract. Submittals requiring priority handling will be submitted by separate submittal using the form and so marked across the face of the form.

5. This Material Approval Submittal is not valid unless it is signed by the contracting officer. This approval is required as called for by the contracting officer under the terms of this contract.

AF IMT 3000, 20030901, V1 (REVERSE)

2019-09-09T15:40:00-0500

ROLAN.PATRICK.M.1515150249

2019-09-16T11:23:32-0500

GARRIGAS.CHRISTA.L.1287173314

TO Contracting Officer: SrA Lydia SimpkinsWater

FROM Contractor: FARR Builders LLC S. Gevers, San Antonio, TX 78210

DATE: 09-Sept.2019

CONTRACT NUMBER: FA4661-15-D-0001

SUBMISSION NUMBER: 80

PREVIOUS SUBMISSION NUMBER: 79

PROJECT NUMBER: FNWZ 12-0053

ITEM NORow1: 1

SPECIFICATION SECTION PARA NODRAWING NORow1: Per Sow

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow1: Signage Details And Color Chart

INITIALRow1: PR

ITEM NORow2:

SPECIFICATION SECTION PARA NODRAWING NORow2:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow2:

INITIALRow2:

ITEM NORow3:

SPECIFICATION SECTION PARA NODRAWING NORow3:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow3: sign color: Bronze Metallic A99

INITIALRow3: PR

ITEM NORow4:

SPECIFICATION SECTION PARA NODRAWING NORow4:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow4:

INITIALRow4:

ITEM NORow5:

SPECIFICATION SECTION PARA NODRAWING NORow5:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow5:

INITIALRow5:

ITEM NORow6:

SPECIFICATION SECTION PARA NODRAWING NORow6:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow6:

INITIALRow6:

ITEM NORow7:

SPECIFICATION SECTION PARA NODRAWING NORow7:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow7:

INITIALRow7:

ITEM NORow8:

SPECIFICATION SECTION PARA NODRAWING NORow8:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow8:

INITIALRow8:

ITEM NORow9:

SPECIFICATION SECTION PARA NODRAWING NORow9:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow9:

INITIALRow9:

ITEM NORow10:

SPECIFICATION SECTION PARA NODRAWING NORow10:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow10:

INITIALRow10:

ITEM NORow11:

SPECIFICATION SECTION PARA NODRAWING NORow11:

DESCRIPTION OF MATERIAL Include Type Model Number Catalog Number Mfg etcRow11:

INITIALRow11:

DATE YYYYMMDD: 2019/09/09

TYPE OR PRINT NAME AND GRADE: Wayne Owens, PS

TO Base Civil Engineering Officer: 502 CE

RNLT:

DATE YYYYMMDD_2:

TYPE OR PRINT NAME AND GRADE_2:

TO AF Contracting Office:

DATE YYYYMMDD_3: 20190909

TYPE OR PRINT NAME AND GRADE_3: Patrick Rolan, GS-12

TO Contractor:

DATE YYYYMMDD_4: 20190909

TYPE OR PRINT NAME AND GRADE_4: Mrs. Christa Garrigas, GS-12

Text5:

Check Box6: Yes

Check Box7: Off

Check Box8: Off

Check Box9: Off

Check Box10: Off

Check Box11: Off

Check Box12: Off

Check Box13: Off

Check Box14: Off

Check Box15: Off

Check Box16: Off

Check Box17: Off

Check Box18: Off

Check Box19: Off

Check Box20: Off

Check Box21: Off

Check Box22: Off

Check Box23: Off

Check Box24: Off

Check Box25: Off

Check Box26: Off

Check Box27: Off

Check Box28: Off

Check Box29: Off

Check Box30: Off

Check Box31: Off

Check Box32: Off

Check Box33: Off

Check Box34: Off

Check Box35: Off

Check Box36: Off

Check Box37: Off

Check Box38: Off

Check Box3: Yes

Check Box50: Off

Check Box4: Yes

Check Box5: Off

Check Box39: Yes

Check Box40: Off

COMMENTS Number to correspond with applicable Item Number on reverseRow1: