3-11-19-25-LIBRARY-01 LEAD-XRF - 30-32 NORTH MAIN STREET KENT CT.pdf.crdownload
CRDOWNLOAD file 3 MB Posted
- Attached to
- Kent Memorial Library Expansion
- Solicitation number
- 33247
- Issued by
- Litchfield County, Connecticut
About this file
This is a lead-based paint X-ray fluorescence (XRF) screening report prepared by Reliance Environmental, LLC for the Kent Memorial Library located at 32 North Main Street, Kent, Connecticut. The assessment was conducted on November 12, 2025, by a certified lead inspector using an RMD LPA-1 XRF analyzer to evaluate lead concentrations on painted surfaces throughout the library building in accordance with Connecticut Department of Energy and Environmental Protection (DEEP) regulations. The inspection encompassed multiple areas including the entry, reception, hallway, offices, bathrooms, kitchen, book stacks, children's room, young adult area, reading room, and basement mechanical spaces. The screening identified non-toxic lead levels (below 1.0 mg/cm²) in most areas of the first floor and basement, with results ranging from -1.2 to -0.1 mg/cm² for components such as window systems, door systems, walls, ceilings, and handrails in these zones.
The assessment revealed significant toxic lead contamination exclusively in the reading room, where painted components including all window systems, bookshelves, door systems, balusters, handrails, and cove base materials measured at or exceeded 9.9 mg/cm², substantially exceeding the 1.0 mg/cm² toxic threshold. Additional reading room components including wall systems and cove base (wood) registered 2.4 to 3.7 mg/cm² and 6.5 mg/cm² respectively, classified as toxic. Consequently, all waste generated from the reading room must be disposed of as lead-contaminated listed hazardous waste, while waste from remaining areas qualifies as standard construction and demolition (C&D) waste exempt from TCLP-lead testing. The report specifies that crews engaged in renovation and demolition activities must comply with OSHA construction industry standards codified under 29 CFR 1926.62. Reliance Environmental, LLC, the contracted entity, holds valid Connecticut Department of Public Health licenses and certifications as a lead consultant contractor, with project personnel including Vidya N. Trivedi, MS (Environmental Engineering), PE, CHMM, certified as a lead inspector, risk assessor, and planner/project designer.
Text of this file
140 Captain Thomas Blvd • Suite 201 • West Haven • CT 06516
(203) 623-3086 | Fax: (203) 553-9069 | vidyatrivedi2002@yahoo.com
November 19, 2025
Ms. Sarah Marshall, Director Kent Memorial Library 32 North Main Street Danbury, CT 06810
Reference: Limited & directed lead paint XRF screening of firehouse located at 32 North Main Street, Kent, CT
Dear Ms. Marshall, This letter is in reference to the recent lead screening conducted in the Firehouse at the above-mentioned facility. The purpose of this assessment was twofold: (1) to determine the concentration of lead on painted surfaces within the Firehouse, and (2) to evaluate construction-related waste materials in accordance with the regulations established by the Connecticut Department of Energy and Environmental Protection
(DEEP).
On November 12, 2025, a representative from Reliance Environmental performed the lead screening using a RMD LPA-1 X-ray fluorescence (XRF) lead paint analyzer (Serial No. 3128). The inspection focused specifically on the kitchen area of the property.
Please refer to the table below for the detailed XRF lead readings obtained during the assessment.
Address: 32 North Main Street, Kent, CT Date: November 12, 2025
Abbreviations Used:
A Side: Front Side of the Building B, C & D Sides are right, rear & left side of the building respectively in the clockwise direction E Side Means Ceiling F Side Means Floor
Note: Please see the attached drawing for side reference.
Calibration at the beginning of Lead Screening = 1.1 mg/cm2 Calibration at the beginning of Lead Screening = 0.8 mg/cm2 Calibration at the beginning of Lead Screening = 1.0 mg/cm2
Calibration at the end of Lead Screening = 1.2 mg/cm2 Calibration at the end of Lead Screening = 0.9 mg/cm2 Calibration at the end of Lead Screening = 1.1 mg/cm2
Sample ID # Room Type Side Component Condition Results (mg/cm2) Comments
1 Entry to the Library A Window System Intact -0.1 Non-Toxic Level of Lead
2 Entry to the Library B Door System Intact -0.5 to -0.2 Non-Toxic Level of Lead
3 Reception B Wall Intact -0.1 Non-Toxic Level of Lead
4 Reception - Hallway E Ceiling Intact -0.8 Non-Toxic Level of Lead
5 Hallway A - D Base of Handrail Intact -0.5 Non-Toxic Level of Lead
6 Office B Wall Intact -0.3 Non-Toxic Level of Lead
7 Office D Window System Intact -0.3 to -0.2 Non-Toxic Level of Lead
8 Office D Door System Intact -0.3 to -0.2 Non-Toxic Level of Lead
9 Bath (Near Reception Area) B Wall Intact -0.4 Non-Toxic
Level of Lead
10 Bath (Near Reception Area) B Window System Intact -0.6 to -0.3 Non-Toxic
Level of Lead
11 Bath (Near Reception Area) C Door System Intact -0.4 to -0.2 Non-Toxic
Level of Lead
12 Book Stacks E Ceiling Intact -0.2 Non-Toxic Level of Lead
13 Children’s Room D Wall System Intact -0.4 Non-Toxic Level of Lead
14 Children’s Room D Window System Intact -0.3 to -0.2 Non-Toxic Level of Lead
15 Kitchen C Wall System Intact -0.1 Non-Toxic Level of Lead
16 Kitchen A Door System Intact -0.4 to -0.2 Non-Toxic Level of Lead
17 Young Adult Area D Wall System Intact -0.3 Non-Toxic Level of Lead
18 Young Adult Area D Window System Intact -0.5 to -0.2 Non-Toxic Level of Lead
19 Entry (To Young Adult Area) C - D Door Systems Intact -0.4 to -0.2 Non-Toxic
Level of Lead
20 Reading Room A - D All Wall Systems Intact 2.4 to 3.7 Toxic Level of Lead
21 Reading Room A - D All Window Systems Intact > 9.9 Toxic Level of Lead
22 Reading Room A – D Bookshelves Intact > 9.9 Toxic Level of Lead
23 Reading Room E Ceiling Intact -1.2 Non-Toxic Level of Lead
24 Reading Room A Door System Intact > 9.9 Toxic Level of Lead
Due to the fact that most of the painted components within the Reading Room were identified with elevated lead concentrations—specifically, XRF readings exceeding 9.9 mg/cm², which is significantly above the toxic lead threshold of ≥1.0 mg/cm²—all waste generated from the Reading Room must be disposed of as lead-contaminated listed hazardous waste.
In contrast, painted components throughout the remainder of the first floor and the basement were found to contain non-toxic levels of lead. As a result, the waste from these areas is exempt from Toxicity Characteristic Leaching Procedure (TCLP-lead) testing and may be disposed of as standard construction and demolition (C & D) waste.
Crew engaged in renovation and demolition activity shall adhere to OSHA construction industry standard codified under 29 CFR 1926.62.
Please feel free to call me at (203) 623-3086 if you have any question or require clarification on the above.
Reliance Environmental, LLC
Vidya N. Trivedi, MS (Env Eng), PE, CHMM CT licensed Asbestos Project Designer • Project Monitor • Inspector • Management Planner CT licensed Lead Consultant Contractor • Lead Inspector • Risk Assessor • Planner & Project Designer AIHA & CT Department of Health Approved Lab Director • Fiber Analyst for PCM samples/Clearances American Industrial Hygiene Association (AIHA) Asbestos Analyst Registry (AAR) #4386
25 Reading Room - Stair F Riser & Tread Intact - 0.2 Non-Toxic Level of Lead
26 Reading Room - Stair A-D Baluster & Handrail Intact > 9.9 Toxic Level of Lead
27 Reading Room D Cove Base (Wood) Intact 6.5 Toxic Level of Lead
Basement – Storage
(Entrance to Mechanical Room)
C Door System Intact -0.4 Non-Toxic Level of Lead
29 Basement – Mechanical D Wall System Intact -0.2 Non-Toxic Level of Lead
FIELD SKETCH
0 4 82 6
DN
UP
UP
DN
DN
DN
AHU
DUCTLESS
Young Adult
Reading Room
Entry
Children's RoomKitchen
Bath
Book Stacks Entry
Office
Bath
Reception
8' - 1"
16' - 3 "
8' - 1"
5' - 2"
26' - 6"
38' - 6 "
24' - 8"
21' - 8 "
4' - 4"
7' - 8" 13 ' - 7 "
8' - 3"
29' - 6"
9'
2"
2 7 ' - 8 "
19' - 7"
31' - 10" 5' - 4"7'
3"
55' - 11"
5'
7' - 1"
9'
5"
18' - 0"
87' - 9"
NE
N W
SW
S E
N
E
S W
DRAWING NUMBER
C L
IE
N
T
D R
A W
IN
G
T
IT
L E
S i l a s
D e a n
H i g h w a y
S u i t e
W e t h e r s f i e l d
C o n n e c t i c u t
T el ep ho ne : 8
-2
T el ef ax : 8
-2
I n t e r n e t w w w
I Q T c o m
DATE:
SCALE:
I Q T
1/8" = 1'-0"
A-1.1
02.11.22
K E
N T
M
EM
O R
IA
L
LI
B
R A
R Y
LI
B R
A R
Y B
U
IL
D
IN
G Fi rs t
Fl oo r Pl an
Kent Memorial Library - Library Building 32 North Main Street, Kent, CT 06757
W Y
ET
H
A R
C H
IT
E
C T
S
W es t M ai n
St re et C he st er , C
T
01.First Floor
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.1 mg/cm2 Wall System
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.4 to -0.2 mg/cm2 Door System
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.3 to -0.2 mg/cm2 Window System
RELIANCE SCAN
Callout -0.4 mg/cm2 Wall System
RELIANCE SCAN
Oval
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.5 to -0.2 mg/cm2 Window System
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.3 mg/cm2 Wall System
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box -0.5 mg/cm2 Base of Hand Rail
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box -0.8 mg/cm2 Ceiling in Hallway
RELIANCE SCAN
Callout -0.4 mg/cm2 Wall
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.6 to -0.3mg/cm2 Window System
RELIANCE SCAN
Oval
RELIANCE SCAN
Text Box -0.2 mg/cm2 Ceiling
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box -0.4 to -0.2 mg/cm2 Door Systems
RELIANCE SCAN
Line
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.4 to -0.2 mg/cm2 Door System
RELIANCE SCAN
Callout -0.1 mg/cm2 Wall
RELIANCE SCAN
Oval
RELIANCE SCAN
Oval
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box -0.3 to -0.2 mg/cm2 Window and Door Systems
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box -0.5 to -0.2 mg/cm2 Door System
RELIANCE SCAN
Oval
RELIANCE SCAN
Oval
RELIANCE SCAN
Oval
RELIANCE SCAN
Oval
RELIANCE SCAN
Text Box -0.1 mg/cm2 Window System
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box -1.2 mg/cm2 Ceiling
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout >9.9 mg/cm2 Door System
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.2 mg/cm2 Stairs (Riser and Tread)
RELIANCE SCAN
Oval
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout >9.9 mg/cm2 Baluster and Hand Rail
RELIANCE SCAN
Text Box All Window Systems are > 9.9
RELIANCE SCAN
Text Box All Book Shelves are >9.9
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout
6.5 mg/cm2 Cove Base (Wood)
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Cross-Out
RELIANCE SCAN
Cross-Out
RELIANCE SCAN
Cross-Out
RELIANCE SCAN
Cross-Out
RELIANCE SCAN
Cross-Out
RELIANCE SCAN
Text Box A
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box C
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box B
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box D
RELIANCE SCAN
Line
RELIANCE SCAN
Callout -0.3 mg/cm2 Wall
RELIANCE SCAN
Text Box
2.4 to 3.7 mg/cm2 All Wall Systems
Reliance-6 Rectangle
Reliance-6 Typewritten Text The Children room was built in 1994.
Use of lead based paint was banned in year 1978.
0 4 82 6
UP
TANK
FURNACE
BOILER
Storage
Stor.
Mechanical 24' - 2"
20' - 11"
3 ' - 6 "
3' - 7"
6' - 6" 5 ' - 2 "
3' - 8"
19' - 9"
27' - 8 "
52' - 3"
30' - 3 "
NE
N W
SW
S E
N
E
S W
DRAWING NUMBER
C L
IE
N
T
D R
A W
IN
G
T
IT
L E
S i l a s
D a n
H i g h w a y
S u i t e
W e t h e r s f i e l d
C o n n e c t i c u t
T el ep ho ne : 8
-2
T el ef ax : 8
-2
I n t e r n e t w w w
I Q T c o m
DATE:
SCALE:
I Q T
1/8" = 1'-0"
A-1.0
02.11.22
K E
N T
M
EM
O R
IA
L
LI
B
R A
R Y
LI
B R
A R
Y B
U
IL
D
IN
G B as em en t
Fl oo r Pl an
Kent Memorial Library - Library Building 32 North Main Street, Kent, CT 06757
W Y
ET
H
A R
C H
IT
E
C T
S
W es t M ai n
St re et C he st er , C
T
00.Basement
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout -0.4 mg/cm2 Door System
RELIANCE SCAN
Oval
RELIANCE SCAN
Callout
0.2 mg/cm2 Wall System
RELIANCE SCAN
Text Box B
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box A
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box D
RELIANCE SCAN
Line
RELIANCE SCAN
Line
RELIANCE SCAN
Text Box C
RELIANCE SCAN
Line
PERFORMANCE CHARACTERISTICS SHEET
RMD LPA-1, PCS Edition 5 Page 1 of 4
Performance Characteristic Sheet
EFFECTIVE DATE: October 25, 2006 EDITION NO.: 5
MANUFACTURER AND MODEL:
Make: Radiation Monitoring Devices Model: LPA-1 Source: 57Co Note: This sheet supersedes all previous sheets for the XRF instrument of the make, model, and source shown above for instruments sold or serviced after June 26, 1995. For other instruments, see prior editions.
FIELD OPERATION GUIDANCE
OPERATING PARAMETERS:
Quick mode or 30-second equivalent standard (Time Corrected) mode readings.
XRF CALIBRATION CHECK LIMITS:
0.7 to 1.3 mg/cm2 (inclusive)
SUBSTRATE CORRECTION:
For XRF results below 4.0 mg/cm2, substrate correction is recommended for:
Metal using 30-second equivalent standard (Time Corrected) mode readings.
None using quick mode readings.
Substrate correction is not needed for:
Brick, Concrete, Drywall, Plaster, and Wood using 30-second equivalent standard (Time Corrected) mode readings Brick, Concrete, Drywall, Metal, Plaster, and Wood using quick mode readings
THRESHOLDS:
30-SECOND EQUIVALENT STANDARD
MODE READING DESCRIPTION SUBSTRATE THRESHOLD
(mg/cm2)
Results corrected for substrate bias on metal substrate only
Brick Concrete Drywall Metal
Plaster Wood
1.0 1.0 1.0 0.9 1.0
QUICK MODE
READING DESCRIPTION SUBSTRATE THRESHOLD
(mg/cm2)
Readings not corrected for substrate bias on any substrate
Brick Concrete Drywall Metal
Plaster Wood
1.0 1.0 1.0 1.0
RMD LPA-1, PCS Edition 5 Page 2 of 4
BACKGROUND INFORMATION
EVALUATION DATA SOURCE AND DATE:
This sheet is supplemental information to be used in conjunction with Chapter 7 of the HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing ("HUD Guidelines").
Performance parameters shown on this sheet are calculated from the EPA/HUD evaluation using archived building components. Testing was conducted on approximately 150 test locations in July 1995.
The instrument that performed testing in September had a new source installed in June 1995 with 12 mCi initial strength.
OPERATING PARAMETERS:
Performance parameters shown in this sheet are applicable only when properly operating the instrument using the manufacturer's instructions and procedures described in Chapter 7 of the HUD Guidelines.
XRF CALIBRATION CHECK:
The calibration of the XRF instrument should be checked using the paint film nearest 1.0 mg/cm2 in the NIST Standard Reference Material (SRM) used (e.g., for NIST SRM 2579, use the 1.02 mg/cm2 film).
If readings are outside the acceptable calibration check range, follow the manufacturer's instructions to bring the instruments into control before XRF testing proceeds.
SUBSTRATE CORRECTION VALUE COMPUTATION:
Chapter 7 of the HUD Guidelines provides guidance on correcting XRF results for substrate bias.
Supplemental guidance for using the paint film nearest 1.0 mg/cm2 for substrate correction is provided:
XRF results are corrected for substrate bias by subtracting from each XRF result a correction value determined separately in each house for single-family housing or in each development for multifamily housing, for each substrate. The correction value is an average of XRF readings taken over the NIST SRM paint film nearest to 1.02 mg/cm2 at test locations that have been scraped bare of their paint covering. Compute the correction values as follows:
Using the same XRF instrument, take three readings on a bare substrate area covered with the NIST SRM paint film nearest 1 mg/cm2. Repeat this procedure by taking three more readings on a second bare substrate area of the same substrate covered with the NIST SRM.
Compute the correction value for each substrate type where XRF readings indicate substrate correction is needed by computing the average of all six readings as shown below.
For each substrate type (the 1.02 mg/cm2 NIST SRM is shown in this example; use the actual lead loading of the NIST SRM used for substrate correction):
Correction value = (1st + 2nd + 3rd + 4th + 5th + 6th Reading) / 6 - 1.02 mg/cm²
Repeat this procedure for each substrate requiring substrate correction in the house or housing development.
EVALUATING THE QUALITY OF XRF TESTING:
Randomly select ten testing combinations for retesting from each house or from two randomly selected units in multifamily housing. Use either the Quick Mode or 30-second equivalent standard (Time Corrected) Mode readings.
RMD LPA-1, PCS Edition 5 Page 3 of 4
Conduct XRF re-testing at the ten testing combinations selected for retesting.
Determine if the XRF testing in the units or house passed or failed the test by applying the steps below.
Compute the Retest Tolerance Limit by the following steps:
Determine XRF results for the original and retest XRF readings. Do not correct the original or retest results for substrate bias. In single-family and multi-family housing, a result is defined as a single reading. Therefore, there will be ten original and ten retest XRF results for each house or for the two selected units.
Calculate the average of the original XRF result and retest XRF result for each testing combination.
Square the average for each testing combination.
Add the ten squared averages together. Call this quantity C.
Multiply the number C by 0.0072. Call this quantity D.
Add the number 0.032 to D. Call this quantity E.
Take the square root of E. Call this quantity F.
Multiply F by 1.645. The result is the Retest Tolerance Limit.
Compute the average of all ten original XRF results.
Compute the average of all ten re-test XRF results.
Find the absolute difference of the two averages.
If the difference is less than the Retest Tolerance Limit, the inspection has passed the retest. If the difference of the overall averages equals or exceeds the Retest Tolerance Limit, this procedure should be repeated with ten new testing combinations. If the difference of the overall averages is equal to or greater than the Retest Tolerance Limit a second time, then the inspection should be considered deficient.
Use of this procedure is estimated to produce a spurious result approximately 1% of the time. That is, results of this procedure will call for further examination when no examination is warranted in approximately 1 out of 100 dwelling units tested.
BIAS AND PRECISION:
Do not use these bias and precision data to correct for substrate bias. These bias and precision data were computed without substrate correction from samples with reported laboratory results less than 4.0 mg/cm2 lead. The data which were used to determine the bias and precision estimates given in the table below have the following properties. During the July 1995 testing, there were 15 test locations with a laboratory-reported result equal to or greater than 4.0 mg/cm2 lead. Of these, one 30-second standard mode reading was less than 1.0 mg/cm2 and none of the quick mode readings were less than 1.0 mg/cm2.
The instrument that tested in July is representative of instruments sold or serviced after June 26, 1995.
These data are for illustrative purposes only. Actual bias must be determined on the site. Results provided above already account for bias and precision. Bias and precision ranges are provided to show the variability found between machines of the same model.
RMD LPA-1, PCS Edition 5 Page 4 of 4
30-SECOND STANDARD MODE
READING MEASURED AT SUBSTRATE BIAS (mg/cm2) PRECISION* (mg/cm2)
0.0 mg/cm2 Brick
Drywall Metal
Plaster Wood
0.0 0.0 0.1 0.3 0.1 0.0
0.1 0.1 0.1 0.1 0.1 0.1
0.5 mg/cm2 Brick
Drywall Metal
Plaster Wood
0.0 0.0 0.0 0.2 0.0 0.0
0.2 0.2 0.2 0.2 0.2 0.2
1.0 mg/cm2 Brick
Drywall Metal
Plaster Wood
0.0 0.0 0.0 0.2 0.0 0.0
0.3 0.3 0.3 0.3 0.3 0.3
2.0 mg/cm2 Brick
Drywall Metal
Plaster Wood
-0.1 -0.1 -0.1 0.1 -0.1 -0.1
0.4 0.4 0.4 0.4 0.4 0.4
*Precision at 1 standard deviation.
CLASSIFICATION RESULTS:
XRF results are classified as positive if they are greater than the upper boundary of the inconclusive range, and negative if they are less than the lower boundary of the inconclusive range, or inconclusive if in between. The inconclusive range includes both its upper and lower bounds. Earlier editions of this XRF Performance Characteristics Sheet did not include both bounds of the inconclusive range as "inconclusive." While this edition of the Performance Characteristics Sheet uses a different system, the specific XRF readings that are considered positive, negative, or inconclusive for a given XRF model and substrate remain unchanged, so previous inspection results are not affected.
DOCUMENTATION:
An EPA document titled Methodology for XRF Performance Characteristic Sheets provides an explanation of the statistical methodology used to construct the data in the sheets, and provides empirical results from using the recommended inconclusive ranges or thresholds for specific XRF instruments. For a copy of this document call the National Lead Information Center Clearinghouse at 1-800-424-LEAD. A HUD document titled A Nonparametric Method for Estimating the 5th and 95th Percentile Curves of Variable-Time XRF Readings Based on Monotone Regression provides supplemental information on the methodology for variable-time XRF instruments. A copy of this document can be obtained from the HUD lead web site, www.hud.gov/offices/lead.
This XRF Performance Characteristic Sheet was developed by QuanTech, Inc., under a contract from the U.S. Department of Housing and Urban Development (HUD). HUD has determined that the information provided here is acceptable when used as guidance in conjunction with Chapter 7, Lead-Based Paint Inspection, of HUD’s Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing.
LEAD LICENSES
10011 51 SP 116•1 -COl -POl 15-1-1
RELIANCE ENVIRONMENTAL LLC
11 OLD FARM RD
WOODBRIDGE CT 06525-2400
Dear RELIANCE ENVIRONMENTAL LLC, Attached you will find your validated license for the coming year.
Should you have any questions about your license renewal, please do not hesitate to write or call:
Department of Public Health P.O. Box 340308
M.S.#12MQA
(860) 509-7603 oplc.dph@ct.gov www.ct.gov/dph/license Hartford, CT 06134-0308
MANISHA JUTHANI, MD, COMMISSIONER
DEPARTMENT OF PUBLIC HEAL TH
STATE OF CONNECTICUT
DEPARTMENT OF PUBLIC HEALTH
PURSUANT TO THE PROVISIONS OF THE GENERAL STATUTES OF CONNECTICUT
THE INDIVIDUAL NAMED BELOW IS LICENSED
BY THIS DEPARTMENT A S A
LEAD CONSUL TANT CONTRACTOR
LICENSE NO.
RELIANCE ENVIRONMENTAL LLC
002070
CURRENT THROUGH
08/31/26
VALIDATION NO.
03-203425
EMPLOYER'S COPY
STATE OF CONNECTICUT
DEPARTMENT OF PUBLIC HEALTH
NAME
RELIANCE ENVIRONMENTAL LLC
VALIDATION NO. LICENSE NO. CURRENT THROUGH
03-203425 002070 08/31/26
PROFESSION
LEAD CONSULTANT CONTRACTOR
INSTIWCTIONS:
I. 0l'h1ch ::i nd ~lgn c11c h or the Gtrds un I his fonu
2. Display the lnr:,:c rnnl in :1 1m u11 i1u•r11 pl:i cc iu ~:our 11 mcc or tll :11.: l' of huNiuos.
.l . The \\:1 ll c1 c i1rcl h fo,· ~·0 11 lo CIIIT)' on \Iliff 1icnm11. H ~·ou do 1H1 I "M1 tu c;irr ~ the ":1 lfc t curd , place il it, a Sl'l" lll'r pl:tcc.
-I . The c111p loyc r 's cu11y Is for IH'rKfllU who musl dt• monst n ill' rnl'l'l'HI lit:l' ll ~urd1.: urtllk 11riuo In nnh~1- lo rl' lain l'mp lnymunl nl" prh' ll ci,:~s. The l'IIIJ1luycr ·s u ni I!; lu he 1u·cst: 11 fl•d to thl' L•m11lo~·c1· and kqif h~· lh¢m :u a 1rnr1 or .\.'O ur pcr101lfll' I fil e. Onll otll.' -1.·op~ of lhb card l'UII be supJ>licd to r ou.
WALLBI'CARD
STATE OF CONNECTICUT
DEPARTMENT OF PUBLIC 1-IEALTI-I
NAME
RELIANCE ENVIRONMENTAL LLC
VALIDATION NO. LICENSE NO. CURRENT THROUGH
03-203425 002070 08/31/26
PROFESSION
LEAD CONSULTANT CONTRACTOR
~ 'N • '! /UN~ SHA ,COMMISSIONER
1001476 SP 0664 -COl -POl 479-1
VIDY A N. TRIVEDI
RELIANCE ENVIRONMNET AL LLC
11 OLD FARM RD
WOODBRIDGE CT 06525-2400
Dear VIDYA N. TRIVEDI, Attached you will find your validated certificate for the coming year. Should you have any questions about your certificate renewal , please do not hesitate to write or call :
Department of Public Health P.O. Box 340308
M.S.#12MQA
(860) 509-7603 oplc.dph@ct.gov www.ct.gov/dph/license Hartford, CT 06134-0308
MANISHA JUTHANI, MD, COMMISSIONER
DEPARTMENT OF PUBLIC HEAL TH
STATE OF CONNECTICUT
DEPARI'MENT OF PUBLIC HEALTH
PURSUANT TO THE PROVISIONS OF THE GENERAL STA TlJTES OF CONNECTICUT
THE INDIVIDUAL NAMED BELOW IS CERTIFIED
BY THIS DEPARTMENT AS A
LEAD INSPECTOR RISK ASSESSOR
CERTIFICATE NO.
VIDYA N. TRIVEDI
002175
CURRENT 11-IROUGH
03/31/26
VALIDATION NO.
03-173643
EMPLOYER'S COPY
STATE OF CONNECTICUT
DEPARTMENT OF PUBLIC HEALTH
NAME
VIDYA N. TRIVEDI
VALIDATION NO. CERTIFICATE NO. CURRENT THROUGH
03-173643 002175 03/31/26
PROFESSION
LEAD INSPECTOR RISK ASSESSOR
----: J -- --· ·------ ..... .,__ ________ .__ .... ______ .._.._ _____ ..,, ---·---------- -·-- -
INSTRUCTIONS:
I. Oclac h a nd ~i1:11 ~tc h oflh l' ca rd -; on 1hh form
2. Dh;pl u~ the la rgr cu rd in a prominent JJl acc in ~our office or plan· of busi nc.,~.
3. The na ll ct c:trd is for )OU to ca r r) o n )O ur penon. lf )OU do 1101 \\ i\ h to carr, thl• n:1ll r1 ca rd. plncr it in :i 'iccurc pfa cc.
4. The cmplo) cr·i cop) is for persons ,,ho must dcmomt rn tc cu rn·nt li ccnsure'n• rt ilkat ion in orde r lo retain cmplo)·mcnt o r prhilel!C!i . T hr crnph,)rr ·\ c:t rd I\ 10 he (H"l'Sl' lll t:d tu the employer and kept by them as a p:1r1 of ) Ollr prrso nnel file. Onl ) ont.• cup ) of thi\ Cllrd c:1 11 he suppli ed to ) OU .
WALLEfCARD
· STATE OF CONNECTICUT
DEPARTMENT OF PUBLIC HEALTH
NAME
VIDYA N. TRIVEDI
VALIDATION NO. CERTIFICATE NO. CURRENT THROUGH
03-173643 002175 03/31/26
PROFESSION
LEAD INSPECTOR RISK ASSESSOR
~cf:r,N'• J/t;We4~HA .co~=
1000186 SP 0664 -C01-P00188-1
VIDYA N. TRIVEDI
RELIANCE ENVIRONMNETAL LLC
11 OLD FARM RD
WOODBRIDGE CT 06525-2400
Dear VIDYA N. TRIVEDI, Attached you will find your validated certificate for the coming year. Should you have any questions about your certificate renewal, please do not hesitate to write or call:
Department of Public Health P.O. Box 340308
M.S.#12MQA
Hartford, CT 06134-0308
(860) 509-7603 oplc.dph@ct.gov www.ct.gov/dph/license
MANISHA JUTHANI, MD, COMMISSIONER
DEPARTMENT OF PUBLIC HEALTH
EMPLOYER'S COPY
STATE OF CONNECTICUT
DEPARTMENf OF PUBLIC HEALTH
NAME
VIDYA N. TRIVEDI
VALIDATION NO. CERTIFICATE NO. CURRENT THROUGH
03-172352 001706 03/31/26
PROFESSION
LEAD PLANNER/PROJECT DESIGNER
~tr, ~ • //ZA,ver/4 ~HA , CO~MSSJONER
STATE OF CONNECTICUT
DEPARTMENT OF PUBLIC HEALTH
PURSUANT TO THE PROVISIONS OF THE GENERAL STATUTES OF CONNECTICUT
THE INDIVIDUAL NAMED BELOW IS CERTIFIED
BY TIIlS DEPARTMENT AS A
LEAD PLANNER/PROJECT DESIGNER
CERTIFICATE NO.
VIDYA N. TRIVEDI
001706
CURRENTTI-IROUGH
03/31/26
VALIDATION NO.
03-172352
~1~ N. 1 /?ANeok · ______;,~.,;,..__HA ~~_____;:
INSTRUCTIONS:
t. Detach and sign eac h of th e cards on th is form
2. Display the la rge card in a pro mine nt place in your office or place of business.
3. T he wa ll et ca rd is fo r yo u to car ry on your perso n. If you do not ,,ish to c:trr~ thC' ,, a ll et card, place it in a SC'c urC' placC'.
4. T he em p loyer 's copy is for perso ns who must dcmonstrntc currC' nt li censure/certi li ca ti on in ord er to retain employ ment or pri"il eges. T he employer 's cnrd is to be presented to the employer and kep t by th em as a part of your perso nn el file. O nl)' one co1>Y of thi s rurd ca n be suppli ed to yo u.
WALLET CARD
STATE OF CONNECTICUT
DEPARTMENf OF PUBLIC HEALTH
NAME
VIDYA N. TRIVEDI
VALIDATION NO. CERTIFICATE NO. CURRENT THROUGH
03-172352 001706 03/31/26
PROFESSION
LEAD PLANNER/PROJECT DESIGNER
Vidya N. Trivedi, MS (Env Eng), PE, CHMM
Other files
Show all 36
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
File details come from the government source that posted it. Updated .