Door_Hardware.pdf

Bonair, Paul D CIV (US)

From: Davis, Charles C CIV CPMS (USA) Sent: Wednesday, May 15, 2019 4:14 PM To: Bonair, Paul D CIV (US) Subject: Door Hardware and keying questions (UNCLASSIFIED)

Classification: UNCLASSIFIED

CLASSIFICATION: UNCLASSIFIED

7. Hardware:

7.1. See attached specification section 08710 Door Hardware; finish to match existing.

7.1.1. Provide new hardware on new doors.

7.1.2. Doors to be keyed to Ft. Benning keying system; provide five keys per level of keying as instructed by DPW real estate division (Eric Connor).

7.1.3. Key all exterior doors alike to match existing door locks.

7.1.4. Interior doors keyed separately.

7.1.5. Master key

7.1.6. Grand master key.

7.1.7. All new locksets to be lever type design.

7.1.8. Install Weather stripping and door bottom seals on doors.

7.1.9. Contractor shall install new doors, frames, hardware, closers, and lock.

7.2. Exterior Door Hardware: Exterior door hardware shall include the following items. Items not specifically identified shall be provided based on suitability of use, durability, and aesthetic character. Finishes on exterior hardware shall match existing hardware.

7.2.1. General: All exterior doors shall have new heavy duty metal kick plates, stainless steel thresholds, weather stripping, door stops, and locking hardware as indicated on the drawings. All door hardware shall be stainless steel construction.

7.2.2. Hinges; shall comply with ANSI/BHMA A156.1; template, full mortise, heavy duty, ball bearing, minimum size 4‐ 1/2" x 4‐1/2", non‐ferrous base metal, non‐removable pins.

7.2.3. Locksets; shall comply with ANSI/BHMA A156.2; , Grade 1, non‐ferrous base metal, 7‐pin removable core compatible with the Base keying system. Lever handles shall be provided per ABA Accessibility Guidelines for Buildings and Facilities. All new locksets to be lever type design.

7.2.4. Exit doors to the exterior (except for mechanical rooms) will be equipped with a full width heavy duty panic hardware device. Exit (Panic) Devices; devices shall comply with ANSI/BHMA 156.3; heavy‐duty touch‐pad type, through‐ bolted mounting. Listed and labeled for panic protection based on UL 305.

7.2.5. Closers; shall comply with ANSI/BHMA A156.4; series C02000, Grade 1, hydraulic, factory‐sized, and adjustable to meet field conditions, mounted on interior of doors. Include overhead hold‐open capability on exterior door closers.

7.2.6. Auxiliary Hardware; shall comply with ANSI/BHMA A156.16. Provide wall or floor stops for all exterior doors.

Provide other hardware as necessary for a complete installation.

7.2.7. Kick Plates; shall comply with ANSI/BHMA A156.6 and shall be non‐ferrous metal.

7.2.8. Thresholds; Thresholds shall comply with ANSI/BHMA A156.21 and ABA Accessibility Guidelines for Buildings and Facilities. Thresholds shall be non‐ferrous metal and shall be provided at all exterior doors.

7.2.9. Weatherstripping; shall comply with ANSI/BHMA A156.22 and shall be provided at all exterior doors.

7.3. Doors to be keyed to Ft. Benning keying system;

7.3.1. Provide five keys per level of keying as instructed by DPW real estate division.

7.3.1.1. Key all exterior doors alike.

7.3.1.2. Interior doors keyed separately.

7.3.1.3. Master key

7.3.1.4. Grand master key.

7.3.2. DPW CORE INFORMATION SHEET

7.3.2.1. Interchangeable Core

7.3.2.2. 7 Pin

7.3.2.3. E Keyway

7.3.2.4. Cylindrical Lock Set (Class 1)

7.3.2.5. Core mark stamped on side of core and face of key

7.3.2.6. All keys cut Tip to Bow

7.3.2.7. 2 operating keys per core

7.3.2.8. Bitting List must be provided to Addressee below by Lock Core Provider.

7.3.2.9. Core mark to be designated by DPW unless using BEST Locks or IDN Armstrong.

7.3.3. Fort Benning Master System

7.3.3.1. Control 40 99 55 7

7.3.3.2. GM 66 13 33 9

7.3.4. Fort Benning Mechanical Core; Used in ALL Electrical, Communication, Mechanical and Elevator equipment Rooms

7.3.4.1. Control 8382446

7.3.4.2. Operating Key 8789826

7.3.4.3. NO Control Keys to be made.

7.3.4.4. NO Mechanical Keys to be made.

7.3.5. Delivery/Shipping:

7.3.6. All Cores & Keys must be sent by supplier to the following address:

7.3.6.1.1.1.1.1. F & A Officer USA, Fort Benning

6650 Meloy Drive, Suite 316 Fort Benning, Georgia 31905 ATTN: DPW Master Planning

C. Craig Davis, RA DPW Engineering Division Meloy Hall, Bldg 6 6650 Meloy Dr.

Fort Benning, GA 31905 706.545.2223

CLASSIFICATION: UNCLASSIFIED