8107_e2v8.pdf

KEYED NOTES

GENERAL NOTES

P

CLOCK

S C A L E I N F E E T

1688 4

P

CLOCK

S S

WIRING IN THIS ROOM.

CONDUIT, BOXES AND

REMOVE ALL IDS-RELATED

P

CLOCK

WIRING IN THIS ROOM.

CONDUIT, BOXES AND

REMOVE ALL IDS-RELATED

P

CLOCK

WIRING IN THIS ROOM.

CONDUIT, BOXES AND

REMOVE ALL IDS-RELATED

P

CLOCK

WIRING IN THIS ROOM.

CONDUIT, BOXES AND

REMOVE ALL IDS-RELATED

S

S S

S

P

L L L L L

CLOSET

COMM.

S

S

RST

P

F

S

S S

S

P P

K

ELEC. & COMM. DEMOLITION

4 4 4 4 4

4 4 4 4

5 5 5 5 5

3 3 3 3

5 5

WIRING IN THIS ROOM.

CONDUIT, BOXES AND

JACKS, RACEWAY,

AND IDS-RELATED

REMOVE ALL SIPRNET 5

4 5 5 5 5

FAP XCV

9 9

FCU

FCU

FCU

FCU

FCU

FCU

FCU

FCU

FCU

FCU

FCU

FCU FCU

FCU

FCU

FCU

FCU

FCU

FCU

FCU

M

LEADER NOTE, SHALL BE REMOVED, COMPLETE.

4. COMMUNICATION JACKS, RACEWAY, BOXES AND CABLE SHOWN AS DASHED, WITH NO

RE-CONNECTED TO REMAIN ACTIVE.

3. RECEPTACLES NOT MOUNTED TO CAGE WALLS OR DEMO'D WALLS SHALL BE

CEILING AND FRONT EXTERIOR SOFFIT AND SURFACE MOUNTED ON HARD CEILINGS, UNO.

2. EXISTING CEILING LIGHTING FIXTURES ARE FLUSH MOUNTED IN SUSPENDED

VERIFIED.

INFORMATION AND FIELD SURVEY, MAY NOT BE ACCURATE AND SHALL BE FIELD

ALARM DEVICES AND COMMUNICATION EQUIPMENT SHOWN ARE BASED ON AVAILABLE

1. RECEPTACLES, COMMUNICATION JACKS, LIGHTING FIXTURES, SWITCHES, FIRE

5 5 5 5

P

WIRE NEW LOWER PULL STATION LOCATION AT LEGAL HEIGHT.

REMOVE (10)- EXISTING MANUAL PULL STATIONS. EXISTING BOX SHALL BE USED TO

WALLS BEING REMOVED.

POINT OF ORIGIN. THIS ALSO APPLIES TO ALL COMMUNICATION JACKS MOUNTED TO CAGE

REMOVE EXISTING VOICE / DATA JACK, BOX, RACEWAY AND CABLE BACK TO COMMUNICATION

TO REMAIN. EXISTING SWITCH LEGS SHALL BE USED IN NEW WORK.

FIXTURES (INCLUDING EXTERIOR FRONT SOFFIT FIXTURES) AND CIRCUITS BACK TO BOXES

IN AREA OF WORK (NOT IN UNFINISHED OPEN STORAGE AREA), REMOVE ALL LIGHTING

WATER COOLERS, REMOVE EXISTING RECEPTACLES AND COVER PLATES.

IN CONJUNCTION WITH REQUIREMENT FOR GFCI RECEPTACLES IN LATRINES AND FOR

ONE SWITCH IS TO BE REMOVED AND REPLACED DUE TO SHARP, DANGEROUS EDGE.

BOXES, CONDUITS AND CONDUCTORS BACK TO PANEL OF ORIGIN OR BOXES TO REMAIN.

IN CONJUNCTION WITH WALL REMOVAL, REMOVE INDICATED EXISTING SWITCHES,

AND BOX. EXISTING CABLE SHALL BE USED IN NEW WORK.

REMOVE INDICATED EXISTING SURFACE MOUNTED COMMUNICATION JACKS, SURFACE RACEWAY

TO REMAIN.

COVER PLATES. REFER TO SHEET E1, LEGEND FOR REQUIREMENTS FOR EXISTING RECEPTACLES

REMOVE COVER PLATES ON RECEPTACLES AND SWITCHES AND PROVIDE NEW IVORY COLORED

IN CONJUNCTION WITH MINOR ARCHITECTURAL WALL WORK (WALLS BEING PAINTED),

COVER PLATE.

AND CABLE BACK TO COMMUNICATION POINT OF ORIGIN. PROVIDE BLANK IVORY COLORED

REMOVE EXISTING FLUSH MOUNTED TELEPHONE JACK (DASHED OPEN TRIANGLE), COVER PLATE

MECHANICAL PLANS FOR ADDITIONAL REQUIREMENTS. ALSO REFER TO SHEET E3, KEYED NOTE 1.

TEMPERATURE PUMP, HOT WATER PUMP, UNIT HEATER AND AIR COMPRESSOR. REFER TO

IN CONJUNCTION WITH MECHANICAL DEMOLITION, REMOVE POWER CONDUCTORS FOR DUAL

BLANK COVERS ON LIGHTING FIXTURE BOX AND SWITCH BOX.

REMOVE DAMAGED WALL MOUNTED LIGHTING FIXTURE, WIRING AND SWITCH, COMPLETE. PROVIDE

TO EXISTING BOX TO REMAIN. EXISTING CIRCUITS SHALL BE RE-USED IN NEW WORK.

CONDUCTORS AND (20)- FAN COIL UNIT (FCU) CIRCUIT CONDUCTORS AND CONDUIT BACK

IN CONJUNCTION WITH MECHANICAL DEMOLITION, REMOVE (5)- EXHAUST FANS' CIRCUIT

A P

P R

D M

A D

E

D I

R E

C T

O R

A T

E

O F

U

B L I

C

W

R K

S

F O

R

L

O N

A

D

W

O

S S

O U

R I

D E

S C

R I

P T I

O N

R E

V I

S I

O N

S

D A

T E

A P

P R

O V

E D

D A

T E

S U

B M I

T T

E D

C H

E C

K E

D

D R

A W

N

D E

S I

G N

E D

C O

O R

D I

N A

T I

O N

D A

T E

D A

T E

D A

T E

SCALE

DATE

PROJECT NO:

DRAWING NO:

OFSHEET

AS SHOWN

DPW 03383-6J

E2

F

M C

R E

P A

B

I

L D I

N G

C O

M

M O

L I

T I

N

A N

E L

E C

T R I

C A

F

A

G G

A R

G G

A R

E L

L

C8107.27

17 NOV 16

J

L

C

E D

F F