FINAL DESIGN_1667770dwg2of2Sentry.pdf

1. WHERE "SPLIT CIRCUIT" IS INDICATED, EXTEND SPLIT CIRCUIT HOME RUNS TO A COMMON JUNCTION BOX ABOVE THE PANEL INDICATED. TIE HOME RUNS TOGETHER USING SPLICE KIT AND EXTEND A SINGLE SET OF CONDUCTORS TO CIRCUIT BREAKER NUMBER INDICATED. WIRING USED IN SPLIT CIRCUITS MUST BE THE SAME SIZE.

2. THE ELECTRICAL DRAWINGS ARE DIAGRAMMATICAL IN NATURE AND INDICATE THE GENERAL LOCATION OF OUTLETS, EQUIPMENT, AND THE CIRCUIT ARRANGEMENT OF THE REQUIRED WIRING. ALTHOUGH THE DRAWINGS DO NOT NECESSARILY INDICATE THE ACTUAL ROUTES OF SURFACE MOUNTED CONDUITS, WHERE INDICATED, THEY MUST BE FOLLOWED AS CLOSELY AS COORDINATION WITH THE WORK OF OTHER TRADES AND SPACE WILL PERMIT. WHERE CONDUIT RUNS ARE NOT SHOWN ON THE DRAWINGS, SUCH AS FOR MECHANICAL EQUIPMENT, COORDINATE CONDUIT RUNS WITH THE WORK OF OTHER TRADES AND STRUCTURE. SIMPLIFY INSTALLATION WHEREVER POSSIBLE, BUT SUBJECT TO APPROVAL BY THE COR FOR VISUAL AND STRUCTURAL REASONS. IT IS NOT WITHIN THE SCOPE OF THE DRAWINGS TO SHOW EVERY NECESSARY OFFSETS, BENDS, PULL BOXES, AND OBSTRUCTIONS. THE DRAWINGS ARE NOT INTENDED TO BE SCALED, REFER TO THE ARCHITECTURAL DRAWINGS FOR DIMENSIONS.

3. NOT EVERY SYMBOL SHOWN IN LEGENDS ARE USED - SEE DRAWINGS FOR APPLICABLE DEVICES.

4. MOUNTING HEIGHTS INDICATED AS '+##' ARE MEASURED FROM FINISHED FLOOR UNLESS OTHERWISE NOTED.

5. PROVIDE LABELS DENOTING EQUIPMENT SERVED AND CORRESPONDING CIRCUIT NUMBER ON DEDICATED RECEPTACLES.

6. SEAL PENETRATIONS OF FIRE- AND/OR SMOKE-RATED CONSTRUCTION WITH U.L. APPROVED STOPPING MATERIAL TO RESTORE THE ORIGINAL RATING OF THE PENETRATED CONSTRUCTION.

7. SEAL PENETRATIONS OF NON-RATED PARTITIONS WITH APPROVED MATERIAL TO PREVENT AIRFLOW AND DEBRIS.

8. MOUNTING HEIGHTS SHOWN ON ELECTRICAL, COMMUNICATIONS, AND SYSTEMS DRAWINGS ARE FOR BIDDING PURPOSES ONLY. REFER TO INTERIOR ELEVATION DRAWINGS FOR MOUNTING HEIGHTS OF DEVICES AND EQUIPMENT. WHERE DISCREPANCIES OCCUR, INTERIOR ELEVATIONS TAKE PRECEDENCE.

9. SUPPORT BOXES AND CONDUIT ABOVE CEILING INDEPENDENTLY. DO NOT SUPPORT FROM SUSPENDED CEILING SYSTEM.

10. WHERE CONCEALED BY INACCESSIBLE FINISHES, PROVIDE ACCESS DOORS FOR JUNCTION & PULL BOXES, CONTROL DEVICES & EQUIPMENT, DISCONNECT SWITCHES, AND OTHER ITEMS REQUIRING SERVICE, MAINTENANCE, OPERATION, OR ADJUSTMENT. SIZE AND LOCATE ACCESS DOORS FOR EASE OF PERFORMANCE OF THE FUNCTION INTENDED. DOORS MUST NOT BE SMALLER THAN 18" x 18". COORDINATE LOCATION OF ACCESS DOORS WITH AFFECTED TRADES. SUBMIT PANEL LOCATIONS FOR APPROVAL BY THE ARCHITECT PRIOR TO INSTALLATION.

11. PROVIDE ADJACENT DEVICES UNDER A COMMON FACEPLATE, WITH NO MORE THAN FOUR DEVICES IN A SINGLE FACEPLATE. WHERE MORE THAN FOUR ADJACENT DEVICES ARE PRESENT, EVENLY DIVIDE DEVICES INTO SEPARATE GROUPS OF NO LESS THAN TWO DEVICES PER GROUP. PROVIDE BARRIERS WITHIN BOXES TO SEPARATE DEVICES WHERE DIFFERENT CIRCUITS AND DIFFERENT VOLTAGES ARE

PRESENT.

12. PROVIDE LUGS AS NECESSARY FOR TERMINATING OVERSIZED CONDUCTORS OR OTHERWISE MAKE PROVISIONS FOR TERMINATING OVERSIZED CONDUCTORS IN DEVICES WHOSE LUGS DO NOT ACCEPT THE

OVERSIZED CONDUCTOR SIZE.

13. SHARED NEUTRAL CONDUCTORS ARE PROHIBITED.

14. OUTAGES MUST BE SCHEDULED WITH A MINIMUM OF 21 CALENDAR DAYS IN ADVANCE. NOTIFY THE BASE PERSONNEL (CONTRACTING OFFICER). MAKE AN APPLICATION FOR OUTAGES TO GOVERNMENT HIGH VOLTAGE FACILITY DEPARTMENT WITH THE PROVIDED REQUEST FORMS AND SUBMIT FOR APPROVAL FOR THE OUTAGES. NO OUTAGES WILL TAKE PLACE WITHOUT WRITTEN AUTHORIZATION TO THE GOVERNMENT PERSONNEL BY THE CONTRACTOR. OUTAGES CAN BE CANCELED BY THE GOVERNMENT UP UNTIL THE SCHEDULED TIME OF THE OUTAGE. OUTAGES MUST BE COORDINATED WITH THE GOVERNMENT PERSONNEL (CONTRACTING OFFICER) TO MINIMIZE TOTAL OUTAGES TO THE FACILITY.

15. ADJUST WIRE SIZES TO COMPENSATE FOR VOLTAGE DROP. THE LENGTH OF A SINGLE PHASE 20A CIRCUIT (ONE-WAY) MUST NOT EXCEED THE FOLLOWING VALUES (BASED ON 16A LOAD):

GENERAL NOTES:

DEVICES/EQUIPMENT MOUNTING HEIGHT (AFF) MEASURED TO:

RECEPTACLES AS INDICATED ON LEGEND/PLANS CENTER

GROUND FAULT CIRCUIT INTERRUPTER 4'-0" CENTER

TOGGLE SWITCHES 4'-0" CENTER

GROUND BUS BARS 2'-0" CENTER

WALL DIMMERS 4'-0" CENTER

INTEGRATED COMMUNICATIONS PANELS 6'-0" TOP

MANUAL MOTOR STARTERS 4'-0" CENTER

GENERATOR REMOTE ALARM ANNUNCIATOR 5'-0" TOP

OCCUPANCY SENSORS - WALL MOUNTED 4'-0" CENTER

GENERATOR TERMINAL BLOCKS 5'-0" TOP

LIGHTING CONTROL PANEL 6'-6" TOP

BAS TERMINAL BLOCKS 5'-0" TOP

LIGHTING CONTROL STATION 4'-0" CENTER

GENERATOR STOP SWITCH 5'-6" CENTER

JUNCTION BOXES AS INDICATED ON LEGEND/PLANS CENTER

GENERATOR TANK FUEL LEVEL INDICATORS 5'-0" TOP

MONITORING/CONTROL PANEL 5'-0" TOP

UPS REMOTE MONITORING PANEL 5'-0" TOP

SURFACE METAL RACEWAYS AS INDICATED ON LEGEND/PLANS TOP

UPS BATTERY MONITORING / CONTROL PANEL 5'-0" TOP

PANELBOARDS 6'-6" TOP

MAIN SWITCHGEAR BATTERY CHARGER 5'-0" TOP

DISCONNECT SWITCHES 5'-0" TOP

RELAY CONTROL PANELS 6'-6" TOP

AUTOMATIC TRANSFER SWITCHES 6'-6" TOP

MANUAL TRANSFER SWITCHES 6'-6" TOP

CONTROL STATIONS 6'-6" TOP

SPD (NON-INTEGRAL) 6'-0" (NTE) TOP

MAGNETIC MOTOR CONTROLLERS 6'-6" TOP

LIGHTING CONTACTORS ENCLOSURES 6'-6" TOP

INDIVIDUAL CKT BREAKERS ENCLOSURES 6'-6" TOP

EMERGENCY POWER OFF SWITCHES 5'-6" CENTER

TIME SWITCHES 6'-6" TOP

TELECOMMUNICATIONS OUTLETS 1'-6" CENTER

TELECOMMUNICATIONS OUTLETS - OVER COUNTER 6" CENTER (OVER TOP OF COUNTER)

MOUNTING HEIGHT SCHEDULE

MOUNTING HEIGHT SCHEDULE NOTES:

1. USE ABOVE INDICATED MOUNTING HEIGHTS UNLESS INDICATED OTHER WISE ON DRAWINGS OR SPECIFICATIONS.

2. COORDINATE MOUNTING HEIGHTS WITH FIELD CONDITIONS, OTHER TRADES, AND RELATED EQUIPMENT.

3. REDUCE MOUNTING HEIGHTS OF FIRE ALARM VISUAL AND AUDIO/VISUAL ALARMS WHERE REQUIRED TO MAINTAIN 6" MINIMUM

SPACING FROM CEILING.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:3

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-001

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

G

EN

ER

AL

N

O

TE

S

KB

12894131

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -0

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

CONDUCTOR SIZE (AWG) MAXIMUM 120V CIRCUIT LENGTH MAXIMUM 277V CIRCUIT LENGTH

#12

#10

#8

#6

60'-0"

90'-0"

140'-0"

225'-0"

135'-0"

210'-0"

330'-0"

525'-0"

SY

M

DE

SC

RI

PT

IO

N

DA

TE

AP

PR

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:4

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-002

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

A

BB

RE

VI

AT

IO

NS

KB

12894132

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -0

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

A

A, AMP AMPERE

AA AMBIENT AIR

ABBREV ABBREVIATION

ABV ABOVE

AC ALTERNATING CURRENT

ACC ACCESS CONTROL

ACT ABOVE COUNTER TOP

AF AMPERE FRAME, AMPERE FUSE

AFC ABOVE FINISHED CEILING

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

AHU AIR HANDLING UNIT

AI ANALOG INPUT

AIC AMPERE INTERRUPTING CURRENT

AL ALUMINUM

AM AMPERE METER

ANN ANNUNCIATOR

ANSI AMERICAN NATIONAL STANDARDS

INSTITUTE

AO ANALOG OUTPUT

AP ANNUNCIATOR POINT

AS AMETER SWITCH

ASYM ASYMMETRICAL

AT AMPERE TRIP

ATS AUTOMATIC TRANSFER SWITCH

ATX AUTO TRANSFORMER

AV AUDIO VISUAL

AVG AVERAGE

AWG AMERICAN WIRE GAUGE

B

BAS BUILDING AUTOMATION SYSTEM

BATT BATTERY, BATTERIES

BB BACKBONE

BC BARE COPPER

BKR BREAKER

BLDG BUILDING

BMS BALANCED MAGNETIC SWITCH

BOC BOTTOM OF CONDUIT

BOT BOTTOM OF TRAY

C

*C CELSIUS

C CONDUIT, COIL

CAT. NO, CAT CATALOG

CBM CERTIFIED BALLAST MANUFACTURER

CCTV CLOSED CIRCUIT TELEVISION CAMERA

CEG COMMON EQUIPMENT GROUND

CFM CUBIC FEET PER MINUTE

CKT CIRCUIT

CLF CURRENT LIMITING FUSE

CLO CLOSET

cm CENTIMETER

CMS COMBINATION MOTOR STARTER

COMPT COMPARTMENT

COND CONDUIT

CONT CONTINUOUS, CONTINUED

CPT CONTROL POWER TRANSFORMER

CPU CENTRAL PROCESSING UNIT

CRAC COMPUTER ROOM AIR CONDITIONING

UNIT

CRI COLOR RENDERING INDEX

CSCCN CENTRAL SCIENTIFIC COMMUNICATIONS

NETWORK

CT CURRENT TRANSFORMER

CU COPPER COEFFICIENT OF UTILIZATION

CY CYCLES

D

D DEPTH, DEEP

DB DUCT BANK

DC DIRECT CURRENT

DEPT DEPARTMENT

DESIG DESIGNATION

DIA DIAMETER

DISC DISCONNECT

DIST,

DISTRIB

DISTRIBUTION

DIV DIVISION

DPDT DOUBLE POLE - DOUBLE THROW

DPST DOUBLE POLE - SINGLE THROW

DS, DSW DISCONNECT SWITCH

DWG DRAWING

E

(E), EX EXISTING

E EMPTY

EGC EQUIPMENT GROUNDING CONDUCTOR

EL, ELEV ELEVATION

ELEC ELECTRICAL / ELECTRIC

EM, EMER EMERGENCY

EMH EXISTING MANHOLE, ELECTRICAL

MANHOLE

EMO EMERGENCY MANUAL OFF

EMS EMERGENCY MANAGEMENT SYSTEM

EMT ELECTRICAL METALLIC TUBING

ENT ELECTRICAL NON-METALLIC TUBING

EO ELECTRICALLY OPERATED

EOL END OF LIFE

EPO EMERGENCY POWER OFF

EPP EXISTING POWER POLE

EPR ETHYLENE-PROPYLENE RUBBER

EQPT EQUIPMENT

ES ENERGY SAVING

ET ELECTRONIC TRIP

ETC ETCETERA

ETL ELECTRICAL TESTING LABORATORIES

EW EACH WAY

EWC ELECTRIC WATER COOLER

EWH ELECTRIC WATER HEATER

EXST EXISTING, EXHAUST

F

(F) FUTURE

F FAHRENHEIT

FA FORCED AIR, FIRE ALARM

FBO FURNISHED BY OTHERS, FURNISHED BY

OWNER

FC FLEXIBLE CONDUIT

FDR FEEDER

FFE FINISHED FLOOR ELEVATION

FIXT FIXTURE

FL FOOT LAMBERTS

FLR FLOOR

FLUOR FLUORESCENT

FREQ FREQUENCY

FRP FIBERGLASS-REINFORCED POLYESTER

FT FOOT

FU FUSE

FUT FUTURE

FVNR FULL VOLTAGE NON-REVERSING

FVR FULL VOLTAGE REVERSING

FWE FURNISHED WITH EQUIPMENT

G g GRAM

G, GND GROUND

GA GAUGE

GALV GALVANIZED

GEC GROUNDING ELECTRODE CONDUCTOR

GEN GENERATOR

GFCI GROUND FAULT EQUIPMENT PROTECTIVE

DEVICE

GFE GOVERNMENT FURNISHED EQUIPMENT,

CONTRACTOR INSTALLED

GFEPD GROUND FAULT EQUIPMENT PROTECTIVE

DEVICE

GFP GROUND FAULT PROTECTION

GFR GROUND FAULT RELAY

GP GENERAL PURPOSE

H

H HEIGHT, HORN

HALOG HALOGEN

HE HIGH EXPOSURE

HH HANDHOLE

HID HIGH INTENSITY DISCHARGE

HORIZ HORIZONTAL

HP HORSEPOWER

HPF HIGH POWER FACTOR

HPS HIGH PRESSURE SODIUM

HRG HIGH RESISTANCE GROUND

HVAC HEATING, VENTILATING AND AIR

CONDITIONING

HZ HERTZ

I

IAW IN ACCORDANCE WITH

ICEA INSULATED CABLE ENGINEERS

ASSOCIATION

IDS INTRUSION DETECTION SYSTEM

IEC INTERNATIONAL ELECTROTECHNICAL

COMMISSION

IEEE INSTITUTE OF ELECTRICAL AND

ELECTRONICS ENGINEERS

IESCR INTEGRATED EQUIPMENT SHORT CIRCUIT

RATING

IESNA, IES ILLUMINATING ENGINEERING SOCIETY OF

NORTH AMERICA

IG ISOLATED GROUND

IMC INTERMEDIATE METAL CONDUIT

INC, INCAND INCANDESCENT

INST INSTRUCTIONS, INSTUMENT /

INSTRUMENTATION

INTER INTERMEDIATE

J

J, JB JUNCTION BOX

K

*K DEGREES KELVIN

K KEY INTERLOCK

KA KILO-AMPERES

KCM, KCMIL 1000 CIRCULAR MILS

KG KILO-GRAM

KM KILO-METER

KV KILO-VOLTS

KVA KILO-VOLT-AMPERES

KVAC KILO-VOLT-AMPERES CONNECTED

KVAD KILO-VOLT-AMPERES DEMAND

KW KILOWATT

KWD KILOWATT DEMAND

L

L LUMEN, LENGTH

LA LIGHTNING ARRESTER

LAN LOCAL AREA NETWORK

LB POUND

LED LIGHT EMITTING DIODE

LPF LOW POWER FACTOR

LRG LOW RESISTANCE GROUND

LSM LONG-TIME/SHORT TIME TRIP

LSI LONG-TIME/SHORT TIME/INSTANTANEOUS

TRIP

LSIG LONG-TIME/SHORT

TIME/INSTANTANEOUS/GROUND FAULT

TRIP

LSIGM LONG-TIME/SHORT

TIME/INSTANTANEOUS/GROUND FAULT

TRIP AND METERING

LSIM LONG-TIME/SHORT TIME/INSTANTANEOUS

TRIP AND METERING

LT LIQUID TIGHT

LTG LIGHTING

LTS LIGHTS

LV LOW VOLTAGE

LVR LOW VOLTAGE RELAY

M m METER

M/G MOTOR / GENERATOR

MAX MAXIMUM

MC METAL-CLAD CABLE

MCB MAIN CIRCUIT BREAKER

MCC MOTOR CONTROL CENTER

MCCB MOLDED CASE CIRCUIT BREAKER

MECH MECHANICAL

MEZZ MEZZANINE

MFR MANUFACTURER

MH MOUNTING HEIGHT, MAN HOLE

MHL METAL HALIDE LAMP

MI MINERAL INSULATED

MIN MINIMUM

MIP MEDICAL ISOLATION PANEL

MLO MAIN LUGS ONLY

mm MILLIMETER

MO MECHANICALLY OPERATED, MOTOR

OPERATOR

MP MOTOR PROTECTOR

MS MASTER SUBSTATION, MOTOR STARTER

MSP MOTOR STARTER PANEL

MT MOUNT

MTD MOUNTED

MTG MOUNTING

MTTOE MOUNTED TO TOP OF EQUIPMENT

MV MEDIUM VOLTAGE

N

(N) NEW

N, NEUT NEUTRAL

NC NORMALLY CLOSED

NO NORMALLY OPEN

NOL NON-OVERLOAD

NA NOT APPLICABLE

NEC NATIONAL ELECTRICAL CODE

NEMA NATIONAL ELECTRICAL MANUFACTURERS

ASSOCIATION

NIC NOT IN CONTRACT

NO. NUMBER

NPF NORMAL POWER FACTOR

NPT NATIONAL PIPE THREAD

NTE NOT TO EXCEED

NTS NOT TO SCALE

O

OC ON CENTER

OL OVERLOAD

OFCI OWNER FURNISHED, CONTRACTOR

INSTALLED

OFE OWNER FURNISHED EQUIPMENT,

CONTRACTOR INSTALLED

OFOI OWNER FURNISHED, OWNER INSTALLED

OPT OPTIONAL

P

P POLE, POWER

PB PRIVATE BRANCH EXCHANGE

PBRD PANELBOARD

PCC POINT OF COMMON COUPLING

PDP POWER DISTRIBUTION PANEL

PDU POWER DISTRIBUTION UNIT

PF POWER FACTOR

PH PHASE

PLC PROGRAMMABLE LOGIC CONTROLLER

PMCS POWER MONITORING AND CONTROL

SYSTEM

PNL PANEL

PT POTENTIAL TRANSFORMER

PVC POLYVINYL CHLORIDE

Q

QTY QUANTITY

R

%R PERCENT RESISTANCE

(R) RELOCATE

R RESISTANCE, RATE, RISE

R/I RECTIFIER / INVERTER

RCPT RECEPTACLE

RCR ROOM CAVITY RATIO

REQD REQUIRED

RFI RADIO FREQUENCY INTERFERENCE

RGS RIGID GALVANIZED STEEL

RM ROOM

RMS ROOT MEAN SQUARE

RQD REQUIRED

RVAT REDUCED VOLTAGE AUTOTRANSFORMER

RVNR REDUCED VOLTAGE NON-REVERSING

RVR REDUCED VOLTAGE REVERSING

T

T&B TOP AND BOTTOM

T, TX TRANSFORMER

T.O.C TOP OF CONDUIT

TB TERMINAL BLOCK

TBD TO BE DETERMINED

TDR TIME DELAY RELAY

TEL TELEPHONE

TEL CAB TELEPHONE CABINET

TJB TERMINAL JUNCTION BOX

TP TRANSFORMER PROTECTION

TSTAT THERMOSTAT

TYP TYPICAL

U

UDS UNITIZED DISTRIBUTION SUBSTATION

UG, UGND UNDERGROUND

UH UNIT HEATER

UL UNDERWRITERS' LABORATORIES

UNO, UON UNLESS NOTED OTHERWISE, UNLESS

OTHERWISE NOTED

UPS UNINTERRUPTIBLE POWER SUPPLY

UTP UNSHIELDED TWISTED PAIR

UV ULTRAVIOLET

V

V VOLT, VOLTS, VOLTMETER

VA VOLT-AMPERE

VAC VOLTS ALTERNATING CURRENT

VAR VOLT AMPERE REACTIVE

VDC VOLTS DIRECT CURRENT

VERT VERTICAL

VESDA VERY EARLY SMOKE DETECTION

VFD VARIABLE FREQUENCY DRIVE

VM VOLT METER

VPE VACUUM PRESSURE ENCAPSULATED

VPI VACUUM PRESSURE IMPREGNATED

VS VOLTMETER SWITCH

VSD VARIABLE SPEED DRIVE

VT VOLTAGE TRANSFORMER

W

W WATTS, WIRE, WIDTH

W/ WITH

W/O WITHOUT

WG WATER GAGE

WHD WATTHOUR DEMAND METER

WP WEATHERPROOF

x

%X PERCENT REACTANCE

X REACTANCE

XFMR TRANSFORMER

XLP CROSS-LINK POLYETHYLENE INSULATION

Y

Y WYE-CONNECTED

Z

%Z PERCENT IMPEDANCE

Z IMPEDANCE

SS

S SPEAKER

S/MH SPACING TO MOUNTING HEIGHT RATIO

SC SHORT CIRCUIT

SCHED SCHEDULE

SE SERVICE ENTRANCE

SEC SECONDS

SECT SECTION

SES SERVICE ENTRANCE SUBSTATION

SHLD SHIELDED, SHIELD

SKVA STARTING KILO-VOLT AMPERES

SP SPARE

SPD SURGE PROTECTIVE DEVICE

SPDT SINGLE POLE-DOUBLE THROW

SPST SINGLE POLE-SINGLE THROW

SQ SQUARE

SS STAINLESS STEEL

SSBJ SUPPLY SIDE BONDING JUMPER

SSL SOLID STATE LIGHT

SSM SOLID STATE METERING

SST SOLID STATE TRIP

ST SHUNT TRIP

STA STATION

STD STANDARD

STP SHIELDED TWISTED PAIR

SW SWITCH

SWBD SWITCHBOARD

SWGR SWITCHGEAR

SYM SYMMETRICAL

SYNCH SYNCHRONIZER

SY

M

DE

SC

RI

PT

IO

N

DA

TE

T75

ATS

G GG

LPS LPS

P

P

JB

ELECTRICAL DISTRIBUTION EQUIPMENT SYMBOLS

FLOOR OR SURFACE MOUNTED 208V PANELBOARD

FLOOR OR SURFACE MOUNTED 480V PANELBOARD

RECESSED 208V PANELBOARD

RECESSED 480V PANELBOARD

GENERAL PURPOSE, DRY TYPE TRANSFORMER. 'T75' IS THE KVA RATING

FOR THE TRANSFORMER. IN THIS EXAMPLE, 'T75' REPRESENTS A

TRANSFORMER RATED 75KVA.

AUTOMATIC TRANSFER SWITCH.

SPD SURGE PROTECTIVE DEVICE

VFD

MOTOR CONNECTION

SINGLE POINT CONNECTION FOR PACKAGED EQUIPMENT

COMBINATION MOTOR STARTER / DISCONNECT

MOTOR STARTER

NON FUSED DISCONNECT

VARIABLE FREQUENCY DEVICE

ELECTRICAL MANHOLE

FUSED DISCONNECT

GROUNDING AND LIGHTNING PROTECTION LEGEND

GROUND ROD.

GROUND ROD IN TEST WELL.

GROUND CONNECTION TO BUILDING STEEL OR EQUIPMENT / VESSEL.

GROUND BAR.

LIGHTNING PROTECTION AIR TERMINAL.

MAIN LIGHTNING PROTECTION CONDUCTOR

LIGHTNING PROTECTION AIR TERMINAL WITH DOWN CONDUCTOR.

BGA BARREL GROUNDING BAR ASSEMBLY; MOUNTED 5'-0" AFF.

GROUNDING CONDUCTOR.

LUMINAIRE LEGEND

aA1

DENOTES POLE MOUNTED SINGLE ARM LUMINAIRE. POLE HEIGHT AS INDICATED.

DENOTES POLE MOUNTED TWIN CONFIGURATION SINGLE ARM LUMINAIRE.

INDIVIDUAL LUMINAIRE TYPE AS INDICATED; POLE HEIGHT AS INDICATED.

DENOTES POLE MOUNTED TRIPLEX CONFIGURED SINGLE ARM LUMINAIRE.

INDIVIDUAL TYPE AS INDICATED; POLE HEIGHT AS INDICATED.

DENOTES POLE MOUNTED QUADRAPLEX CONFIGURED SINGLE ARM

LUMINAIRE. INDIVIDUAL LUMINAIRE TYPE AS INDICATED; POLE HEIGHT AS

INDICATED.

PENDANT OR CEILING MOUNTED ILLUMINATED EGRESS EXIT SIGN. WHERE

USED, DIRECTIONAL ARROWS AS INDICATED. MOUNT 8'-0" ABOVE FINISHED

FLOOR, UNLESS INDICATED OTHERWISE.

ROUND PENDANT LUMINAIRE. SEE LUMINAIRE ANCILLARIES BELOW FOR

ADDITIONAL REQUIREMENTS.

WALL MOUNTED EGRESS LIGHT. MOUNT 8'-0" ABOVE FINISHED FLOOR,

UNLESS INDICATED OTHERWISE. NUMBERS OF LAMP HEADS AS INDICATED IN

LIGHTING FIXTURE SCHEDULE.

WALL MOUNTED REMOTE LAMP HEAD EMERGENCY LIGHT. MOUNT 8'-0" ABOVE

FINISHED FLOOR, UNLESS INDICATED OTHERWISE. NUMBERS OF LAMP HEADS

AS INDICATED IN LIGHTING FIXTURE SCHEDULE.

NUMERAL = CIRCUIT NUMBER

LOWERCASE ALPHANUMERIC CHARACTER = LIGHTING SWITCH OR CONTROL

ZONE

ALPHANUMERIC TAG = LUMINAIRE TAG; COORDINATE WITH LIGHTING FIXTURE

SCHEDULE

WALL MOUNTED ILLUMINATED EGRESS EXIT SIGN. WHERE USED, DIRECTIONAL

ARROWS AS INDICATED. MOUNTED 8'-0" AFF UNLESS INDICATED OTHERWISE .

SITE POLE LUMINAIRE WITH CONCRETE FOOTING. NUMBERS OF LAMP HEADS

AS INDICATED IN LIGHTING FIXTURE SCHEDULE. SEE LUMINAIRE ANCILLARIES

BELOW FOR ADDITIONAL REQUIREMENTS.

SURFACE OR PENDANT MOUNTED TRACK LUMINAIRE. NUMBERS OF LAMP

HEADS AS INDICATED IN LIGHTING FIXTURE SCHEDULE. SEE LUMINAIRE

ANCILLARIES BELOW FOR ADDITIONAL REQUIREMENTS.

2'X2' RECESSED LUMINAIRE

2'X2' RECESSED CENTER BASKET LUMINAIRE

2'X2' SURFACE LUMINAIRE

2'X2' SURFACE CENTER BASKET LUMINAIRE

2'X2' RECESSED LUMINAIRE CONNECTED TO EMERGENCY SOURCE

DOWNLIGHT LUMINAIRE

DOWNLIGHT LUMINAIRE CONNECTED TO EMERGENCY SOURCE

DOWNLIGHT WALL WASHER LUMINAIRE (CHEVRON(S) POINT TO WASHED

WALL(S))

1'X4' RECESSED LUMINAIRE

1'X4' RECESSED CENTER BASKET LUMINAIRE

1'X4' SURFACE LUMINAIRE

1'X4' SURFACE CENTER BASKET LUMINAIRE

1'X4' RECESSED LUMINAIRE CONNECTED TO EMERGENCY SOURCE

2'X4' RECESSED LUMINAIRE

2'X4' RECESSED CENTER BASKET LUMINAIRE

2'X4' SURFACE LUMINAIRE

2'X4' SURFACE CENTER BASKET LUMINAIRE

2'X4' RECESSED LUMINAIRE CONNECTED TO EMERGENCY SOURCE

1'X8' LINEAR PENDANT LUMINAIRE

1'X4' PENDANT LUMINAIRE

1'X4' PENDANT LUMINAIRE CONNECTED TO EMERGENCY SOURCE

1'X8' LINEAR PENDANT LUMINAIRE CONNECTED TO EM. SOURCE

WALL MOUNTED LUMINAIRE. SHADING DENOTES EMERGENCY POWER.

WIRING SYSTEM/RACEWAY/CABLE TRAY LEGEND

BRANCH CIRCUIT "HOMERUN", TIC MARKS INDICATE NUMBER OF CONDUCTORS

(INCLUDING NEUTRAL). #10 INDICATES AWG WIRE SIZE, AND 3/4" INDICATES

CONDUIT SIZE. WIRE AND CONDUIT SIZE IS APPLICABLE TO EACH CIRCUIT

INDICATED FOR ENTIRE LENGTH OF CIRCUIT. BRANCH CIRCUIT WIRING MUST

INCLUDE A #12 AWG GROUND IN 3/4" CONDUIT. ARROW HEADS DENOTE A

HOMERUN TO PANELBOARD. NUMBER OF ARROWHEADS INDICATE NUMBER OF

CIRCUITS IN CONDUIT. "LP-1,3" INDICATES PANEL AND CIRCUIT NUMBERS.

LP-1,3#10,

3/4"

SINGLE CONDUIT CAPPED

MULTIPLE CONDUITS, INDIVIDUALLY CAPPED. WHERE NUMERIC DESIGNATION

INDICATED, DENOTES QUANTITY OF CAPPED CONDUITS. IN THIS EXAMPLE,

THREE CAPPED CONDUITS

RACEWAY CONTINUATION

CONDUIT OR CABLE TURNING UP OR TOWARD THE OBSERVER

CONDUIT OR CABLE TURNING DOWN OR AWAY FROM THE OBSERVER

CONDUIT OR CABLE CHANGE IN ELEVATION

CABLE TRAY

CONDUIT WITH BUSHING

A

R1

SWITCH LEG CONNECTED TO SWITCH "A"

SWITCH LEG CONNECTED TO RELAY #1 IN LIGHTING CONTROL PANEL

INDICATED.

DUPLEX RECPTACLE. UNLESS INDICATED OTHERWISE, RECEPTACLES ARE FLUSH

MOUNTED, 20A,125V, 1PH, 2P, 3W, NEMA 5-20R.

13 DENOTES ONE OR TWO NUMERIC DIGIT BRANCH CIRCUIT NUMBER

WP WEATHER-RESISTANT, WEATHERPROOF WITH HINGED COVER

L PAD LOCKABLE COVER

GFI GFCI TYPE, WIRED FOR GFCI TRIP FOR DESIGNATED RECEPTACLE ONLY (NON-

FEED-THRU INSTALLATION)

TV TELEVISION RECEPTACLE TYPE RECEPTACLE; COORDINATE MOUNTING HEIGHT AND

EXACT LOCATION WITH OWNER'S REPRESENTATIVE PRIOR TO INSTALLATION

TWO DUPLEX (QUAD) RECEPTACLES. UNLESS INDICATED OTHERWISE, RECEPTACES ARE

FLUSH MOUNTED, 20A, 125V, 1PH, 2P, 3W, NEMA 5-20R.

SIMPLEX RECEPTACLE. UNLESS INDICATED OTHERWISE, RECEPTACLES ARE FLUSH

MOUNTED, 20A,125V,1PH, 2P, 3W, NEMA 5-20R.

SPECIAL PURPOSE RECEPTACLE, UNLESS INDICATED OTHERWISE, RECEPTACLES ARE FLUSH

MOUNTED. RECEPTACLE NEMA TYPES INDICATED ON THE SPECIAL RECEPTACLE SCHEDULE.

WIRING DEVICE LEGEND

WP-WIN WEATHER-RESISTANT TYPE, WEATHERPROOF WITH WHILE-IN-USE COVER

TR TAMPER RESISTANT TYPE RECEPTACLE

IG ISOLATED GROUNDING TYPE RECEPTACLE

SPD SURGE PROTECTIVE DEVICE TYPE RECEPTACLE

FLUSH FLOOR TYPE FLOOR BOX. PROVIDE PER MANUFACTURER INSTRUCTION.

POWER POLE WITH DUPLEX RECEPTACLES, LENGTH AS NEEDED TO EXTEND ABOVE

CEILING; SHADED AREA DENOTES TELECOMMUNICATION RACEWAY.

XP EXPLOSION PROOF TYPE, RATED FOR AREA CLASSIFICATION IN WHICH IT IS INSTALLED.

CEILING MOUNTED DUPLEX RCPT. UNLESS INDICATED OTHERWISE, 20A,125V, 1PH, 2P, 3W,

NEMA 5-20R

CEILING MOUNTED SPECIAL PURPOSE RECEPTACLE. TYPES ARE AS NOTED

IN THE SPECIAL RECEPTACLE SCHEDULE.

CORD REEL

F IN WALL FURNITURE CONNECTION. PROVIDE PER MFR INSTRUCTION.

NUMERAL = CIRCUIT NUMBER

GFIWP

CAPITAL LETTER(S) = SPECIAL DESIGNATOR SUBSCRIPT DEFINED ABOVE

PR PROJECTOR RECEPTACLE LOCATED WITHIN PROJECTOR OR CEILING MOUNT

SPLIT YOKE DUPLEX RECPTACLE WITH TOP BEING CONTROLLED. UNLESS INDICATED

OTHERWISE, RECEPTACLES ARE FLUSH MOUNTED, 20A,125V, 1PH, 2P, 3W, NEMA 5-20R.

UTILIZE VACANCY / OCCUPANCY SENSOR SERVING THE ROOM UNLESS OTHERWISE NOTED.

PROVIDE PLUG LOAD CONTROLLER FOR EACH ROOM SERVED.

SWITCHED TWO DUPLEX (QUAD) RECEPTACLES. QUAD RECEPTACLES HAVE CONTROLLED

AND NON-CONTROLLED OUTLETS FED FROM THE SAME CIRCUIT, BUT A SPLIT YOKE IS NOT

REQUIRED. UNLESS INDICATED OTHERWISE, RECEPTACES ARE FLUSH MOUNTED, 20A,

125V, 1PH, 2P, 3W, NEMA 5-20R. UTILIZE VACANCY / OCCUPANCY SENSOR SERVING THE

ROOM UNLESS OTHERWISE NOTED. PROVIDE PLUG LOAD CONTROLLER FOR EACH ROOM

SERVED.

DUPLEX RECPTACLE. UNLESS INDICATED OTHERWISE, RECEPTACLES ARE FLUSH

MOUNTED, 20A,125V, 1PH, 2P, 3W, NEMA 5-20R, MOUNTED 6" ABOVE COUNTERTOP OR

BACKSPLASH UNLESS OTHERWISE NOTED.

DUPLEX RECPTACLE. UNLESS INDICATED OTHERWISE, RECEPTACLES ARE FLUSH

MOUNTED, 20A,125V, 1PH, 2P, 3W, NEMA 5-20R ON AN EMERGENCY CIRCUIT.

+48" DENOTES THE MOUNTING HEIGHT IN INCHES AFF

+36" +(INCHES) = HEIGHT IN INCHES ABOVE FINISHED FLOOR

U USB CHARGING

A ARC FAULT CIRCUIT INTERRUPTER

EWC ELECTRIC WATER COOLER

R

WHEN USED ON DEMOLITION PLANS: DEMOLISH DEVICE AND FACEPLATE, OUTLET BOX TO

REMAIN.

WHEN USE ON WORK PLANS: PROVIDE DEVICE IN EX. OUTLET BOX.

A5

FLUSH FLOOR TYPE FLOOR BOX. PROVIDE PER MANUFACTURER INSTRUCTION.

RECEPTACLE NEMA TYPES INDICATED ON THE SPECIAL RECEPTACLE SCHEDULE.

POWER POLE WITH DUPLEX RECEPTACLES, LENGTH AS NEEDED TO EXTEND ABOVE

CEILING; SHADED AREA DENOTES TELECOMMUNICATION RACEWAY. RECEPTACLE NEMA

TYPES INDICATED ON THE SPECIAL RECEPTACLE SCHEDULE.

WALL MOUNTED TWO-COMPARTMENT SURFACE MOUNTED RACEWAY WITH DUPLEX 120V, 20A,

3-WIRE, NEMA 5-20R RECEPTACLES AT 18" ON CENTER. MOUNT 6" ABOVE COUNTER TOP,

UNLESS INDICATED OTHERWISE.

SURFACE MOUNTED RECEPTACLE

JUNCTION BOX FOR ELECTRICAL EQUIPMENT CONNECTION

LIGHTING CONTROL DEVICE LEGEND

3 THREE WAY.

4 FOUR WAY.

XP EXPLOSION PROOF

MC 3 POSITION, MOMENTARY CONTACT WITH CENTER OFF.

WP WEATHERPROOF.

M SURFACE MOUNTED MOTOR RATED WITH OVERLOAD ELEMENTS, CONTINOUS

CURRENT RATING AND QUANTITY OF POLES AS NEEDED FOR EQUIPMENT

SERVED.

T ADJUSTABLE TIMER SWITCH

P PHOTOCELL MANUAL OVERRIDE SWITCH.

PL ILLUMINATED SWITCH (WHEN OFF)

OS OCCUPANCY SENSOR [WITH MANUAL OVERRIDE].

3a

LOWERCASE LETTER(S) = CONTROL ZONE

CAPITAL LETTER(S) AND/OR NUMERAL = SPECIAL DESIGNATOR SUBSCRIPT

DEFINED ABOVE

LIGHTING CONTROL DEVICE IDENTIFICATION (TYPICAL FOR ALL LIGHTING

CONTROL DEVICE SYMBOLS WHERE USED)

D WALL DIMMER.

V VACANCY SENSOR/SWITCH

CEILING MOUNTED PASSIVE INFRARED OCCUPANCY SENSOR

D

P

CEILING MOUNTED DUAL-TECHNOLOGY VACANCY SENSOR

CEILING MOUNTED DAYLIGHT SENSOR

CEILING MOUNTED PHOTO SENSOR

DP DOUBLE POLE.

VD VACANCY SENSOR/DIMMER

O OCCUPANCY SENSOR/SWITCH

OD OCCUPANCY SENSOR/DIMMER

F WIRELESS CEILING FAN CONTROL STATION

V

V

V

O

O

O

CEILING MOUNTED DUAL-TECHNOLOGY OCCUPANCY SENSOR

CEILING MOUNTED DUAL-TECHNOLOGY CORRIDOR OCCUPANCY SENSOR

O

O

CEILING MOUNTED PASSIVE INFRARED CORRIDOR OCCUPANCY SENSOR

CEILING MOUNTED ULTRASONIC OCCUPANCY SENSOR

O CEILING MOUNTED ULTRASONIC CORRIDOR OCCUPANCY SENSOR

CEILING MOUNTED PASSIVE INFRARED VACANCY SENSOR

CEILING MOUNTED ULTRASONIC VACANCY SENSOR

O

O

O WALL MOUNTED ULTRASONIC OCCUPANCY SENSOR

WALL MOUNTED DUAL-TECHNOLOGY OCCUPANCY SENSOR

WALL MOUNTED PASSIVE INFRARED OCCUPANCY SENSOR

WALL MOUNTED ULTRASONIC VACANCY SENSOR

WALL MOUNTED DUAL-TECHNOLOGY VACANCY SENSOR

WALL MOUNTED PASSIVE INFRARED VACANCY SENSOR

V

V

V

RECESSED WALL MOUNTED SWITCH. PROVIDE ADJACENT DEVICES UNDER

COMMON FACEPLATE, FOUR DEVICES MAXIMUM PER FACEPLATE. EVENLY

DIVIDE DEVICES INTO SEPARATE GROUPS WHERE ADJCENT DEVICES EXCEEDS

FOUR.

SURFACE WALL MOUNTED SWITCH. PROVIDE ADJACENT DEVICES UNDER

COMMON FACEPLATE, FOUR DEVICES MAXIMUM PER FACEPLATE. EVENLY

DIVIDE DEVICES INTO SEPARATE GROUPS WHERE ADJACENT DEVICES EXCEEDS

FOUR.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:4

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-003

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

S

YM

BO

LS

KB

12894133

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -0

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

SY

M

DE

SC

RI

PT

IO

N

DA

TE

JB

JB

LOW VOLTAGE DRAWOUT CURRENT LIMITING CIRCUIT BREAKER.

LSIG1600 AF

800 AS

600 AT

F-800 A C.L.

MEDIUM VOLTAGE DRAWOUT CIRCUIT BREAKER. L LONG PICKUP AND TIME DELAY PROTECTION

PROTECTIONDESIGNATION

SINGLE LINE DIAGRAM LEGEND

LOW VOLTAGE DRAWOUT CIRCUIT BREAKER.

S SHORT PICKUP AND TIME DELAY PROTECTION

I INSTANTANEOUS PICKUP PROTECTION

G GROUND (EARTH) PICKUP AND TIME DELAY PROTECTION

N NEUTRAL PROTECTION

LSIG

250 AF

225 AT

LOW VOLTAGE MOLDED CASE CIRCUIT BREAKER.

LSIG1600 AF

800 AS

600 AT

KEY INTERLOCK

PROTECTION DEVICE FEATURES / ACCESSORIESDESIGNATION

NOTE: MULTIPLE DESIGNATIONS MAY BE ADJACENT TO DEVICE.

K

ST SHUNT TRIP

ET ELECTRONIC TRIP

LSIG

1200/5

SOLID STATE TRIP UNIT WITH CT INPUT OR MODULE CAPABLE OF

MONITORING AMPS, INSTANTANEOUS KW, PEAK KW AND KWH.

TRANSFORMER.

PHASE CURRENT TRANSFORMER.

100 VA

POTENTIAL TRANSFORMER.

CONTROL POWER TRANSFORMER.

FUSE

SINGLE LINE DIAGRAM LEGEND

SURGE PROTECTIVE DEVICE.

NON-FUSED DISCONNECT / SAFETY SWITCH.

60A/3P IN THIS EXAMPLE. DENOTES 60 AMPERES / 3 POLE.

F-30A IN THIS EXAMPLE, DENOTES FUSED WITH 30 AMPERE

FUSES.

F-MFR

DENOTES FUSE RATING IN ACCORDANCE WITH MANUFACTURER'S

INSTRUCTIONS FOR THE UTILIZATION EQUIPMENT PROTECTED BY

THE FUSES.

N3R IN THIS EXAMPLE, DENOTES NEMA 3R ENCLOSURE.

SN DENOTES SOLID NEUTRAL.

N.C.

30A/3P

F-MFR

N.C.

30A/3P

F-30A

FUSED DISCONNECT / SAFETY SWITCH.

N.C. DENOTES NORMALLY CLOSED.

N.O. DENOTES NORMALLY OPEN.

T-PD2A

30KVA

480 V- 208/120 V

SINGLE LINE DIAGRAM LEGEND

E

RVPW1

MOTOR CONTROL CENTER MOTOR STARTER OR LOCAL

CONTROLLER. IN THIS EXAMPLE, '1' DENOTES NEMA SIZE, 'RVPW'

DENOTES REDUCED VOLTAGE PART-WINDING, WHERE INDICATED, 'E'

DENOTES ELECTRONIC OR SOLID STATE OVERLOAD RELAY. UNLESS

INDICATED OTHERWISE, LOCAL CONTROLLER ENCLOSURES ARE

RATED NEMA 1.

E

RVSS1

MOTOR CONTROL CENTER MOTOR STARTER OR LOCAL

CONTROLLER. IN THIS EXAMPLE, '1' DENOTES NEMA SIZE, 'RVSS'

DENOTES REDUCED VOLTAGE SOLID STATE SOFT STARTER, WHERE

INDICATED, 'E' DENOTES ELECTRONIC OR SOLID STATE OVERLOAD

RELAY. UNLESS INDICATED OTHERWISE, LOCAL CONTROLLER

ENCLOSURES ARE RATED NEMA 1.

WD1

MOTOR CONTROL CENTER MOTOR STARTER OR LOCAL CONTROLLER.

IN THIS EXAMPLE, '1' DENOTES NEMA SIZE, 'WD' DENOTES WYE-DELTA

STARTER, WHERE INDICATED, 'E' DENOTES ELECTRONIC OR SOLID

STATE OVERLOAD RELAY. UNLESS INDICATED OTHERWISE, LOCAL

CONTROLLER ENCLOSURES ARE RATED NEMA 1.

521200A

MR

1200/5

ZERO SEQUENCE CURRENT TRANSFORMER.

50/5

MSCT1

MOTOR CONTROL CENTER MOTOR STARTER OR LOCAL

CONTROLLER. IN THIS EXAMPLE, '1' DENOTES NEMA SIZE, 'MSCT'

DENOTES MULTI-SPEED CONSTANT TORQUE STARTER, WHERE

INDICATED, 'E' DENOTES ELECTRONIC OR SOLID STATE OVERLOAD

RELAY. UNLESS INDICATED OTHERWISE, LOCAL CONTROLLER

ENCLOSURES ARE RATED NEMA 1.

MSVT1

MOTOR CONTROL CENTER MOTOR STARTER OR LOCAL CONTROLLER.

IN THIS EXAMPLE, '1' DENOTES NEMA SIZE, 'MSVT' DENOTES MULTI-

SPEED VARIABLE TORQUE STARTER, WHERE INDICATED, 'E' DENOTES

ELECTRONIC OR SOLID STATE OVERLOAD RELAY. UNLESS INDICATED

OTHERWISE, LOCAL CONTROLLER ENCLOSURES ARE RATED NEMA 1.

ADJUSTABLE PROTECTION DESIGNATIONS

MSCH1

MOTOR CONTROL CENTER MOTOR STARTER OR LOCAL

CONTROLLER. IN THIS EXAMPLE, '1' DENOTES NEMA SIZE, 'MSCH'

DENOTES MULTI-SPEED CONSTANT HORSEPOWER STARTER,

WHERE INDICATED, 'E' DENOTES ELECTRONIC OR SOLID STATE

OVERLOAD RELAY. UNLESS INDICATED OTHERWISE, LOCAL

CONTROLLER ENCLOSURES ARE RATED NEMA 1.

MOTOR; EQUIPMENT IDENTIFICATION AND HORSEPOWER AS

INDICATED.

ELECTRONIC METERING MODULE: MICROPROCESSOR BASED FOR

METERING, ANALYZING, WAVEFORM CAPTURE AND CAPABLE OF

PROVIDING MONITORED DATA PARAMETERS

LMU

LOCAL MONITORING UNIT FOR SWITCHGEAR ASSEMBLIES

CAPABLE OF UP TO 40 SEPARATE DATA INPUTS FROM BREAKER

LSIG'S, EMM'S AND MFR'S; CONFIGURABLE DISPLAY SCREEN; DATA

OUTPUT PORTS

CPT480V 10KVA,

1PH 120/240V

PT

KVAR

VARIABLE POWER FACTOR CORRECTION CAPACITOR BANK.

SPD

N.C.

600 A

LOAD INTERRUPTER SWITCH.

EMM

EF-01

M MULTIFUNCTION METER

KT30Y

480 V- 208/120 V ISOLATION TRANSFORMER.

CABLE LUG TERMINATION

LA'S

LIGHTNING ARRESTER. NUMERIC VALUE DENOTES

QUANTITY.

L ATS

P S

TRANSFER SWITCH. 'ATS' DENOTES AUTOMATIC TRANSFER TYPE,

'MTS' DENOTES MANUAL TRANSFER TYPE. 'P' DENOTES PRIMARY

POWER SOURCE; 'S' DENOTES SECONDARY POWER SOURCE; 'L'

DENOTES TRANSFER SWITCH LOAD SIDE CONNECTION POINT.

PNL L1A

PNL L1A

PANELBOARD WITH A VOLTAGE OF 480V OR HIGHER.

PANELBOARD WITH VOLTAGE UNDER 480V.

DENOTES BRANCH CIRCUIT / FEEDER IN CABLE TRAY.

DENOTES BRANCH CIRCUIT / FEEDER IN CONDUIT.

DENOTES GROUNDING SYSTEM.

DENOTES ELECTRICAL EQUIPMENT BUS.

DENOTES DATA CIRCUITRY

DENOTES FUTURE CIRCUIT / EQUIPMENT

DENOTES EQUIPMENT ENCLOSURE.

BATTERY.

DIGITAL METER.DM

E ENGINE.

G GENERATOR.

GFP GROUND FAULT PROTECTION.

GROUNDING CONNECTION.

LOADBANK.

FUSED DRAWOUT POTENTIAL TRANSFORMER.

FUSED POTENTIAL TRANSFORMER.

POWER FILTER.

SURGE PROTECTIVE DEVICE.

R1 RELAY.

UPS AND BATTERY.

LSIG

1600 AF

800 AT

N.C.

30A/3P

(3) F-30A

DEVICE ADJUSTABLE PROTECTION OPTIONS. LONG, SHORT,

INSTANTANEOUS, AND GROUND PICKUPS IN THIS EXAMPLE.

"AF" DENOTES FRAME SIZE, "AT" DENOTES TRIP SETTING.

1600A FRAME WITH 800A TRIP IN THIS EXAMPLE.

DENOTES SWITCH SIZE AND POLES. 30A, 3-POLE SWITCH IN

THIS EXAMPLE.

DENOTES QUANTITY AND RATING OF FUSES. THREE 30A IN

THIS EXAMPLE.

DENOTES ORIENTATION OF SWITCH. NORMALLY CLOSED IN

THIS EXAMPLE.

FEEDER / BRANCH CIRCUIT DESIGNATION. IN THIS EXAMPLE, '13Y'

REFERS TO THE SYMBOL COLUMN OF THE FEEDER/BRANCH CIRCUIT

SCHEDULE. THE ASSOCIATED SYMBOL DESIGNATION DENOTES THE

FEEDER / BRANCH CIRCUIT REQUIREMENTS FOR THE ITEM TAGGED.

13Y

TELECOMMUNICATIONS LEGEND

DOORBELL PUSHBUTTON MOUNTED 48" AFF TO CENTER OF BOX UNLESS

OTHERWISE NOTED.

WALL MOUNTED CALBE TV OUTLET MOUNTED 18" AFF TO CENTER OF BOX

UNLESS OTHERWISE NOTED.

WIRELESS ACCESS POINT

DATA/VOICE WALL MOUNTED RECEPTACLE

DATA WALL MOUNTED RECEPTACLE

DATA CEILING MOUNTED RECEPTACLE

DATA WIRELESS ACCESS POINT

DATA FLOOR BOX

DATA/VOICE CEILING MOUNTED RECEPTACLE

TV

CEILING MOUNTED JUNCTION BOX.

T- L P - S B

ALPHANUMERIC CHARACTER DENOTING IF EQUIPMENT IS ON

STANDBY (SB) POWER. ABSENCE OF CHARACTERS INDICATES

EQUIPMENT IS NOT ON STANDBY POWER.

ELECTRICAL EQUIPMENT NOMENCLATURE

SINGLE OR DOUBLE ALPHANUMERIC CHARACTER DENOTING

EQUIPMENT TYPE DESIGNATION, AS FOLLOWS:

L -208Y/120V POWER

H -480Y/277V POWER

MD -MAIN DISTRIBUTION

P -POWER PANEL

WHERE APPLICABLE, SINGLE TO TRIPLE ALPHANUMERIC CHARACTER

DENOTING EQUIPMENT TYPE MODIFIER, AS FOLLOWS:

A - AUTOMATIC TRANSFER SWITCH.

T - TRANSFORMER

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:4

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-004

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

S

YM

BO

LS

KB

12894134

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -0

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

SY

M

DE

SC

RI

PT

IO

N

DA

TE

G GG G G

G G

G G

G G

G

G G

G G

G G

G

G GG G G G G

G G

G G

G G

G G

G G G G

G GG G

LPS LPSLPS LPS

LPS LPSLPS LPS

LP

S

LP

S

LP

S

LP

S

LP

S

LP

S

LP

S

LP

S

LP

S

LP

S

B

A

B

A

PLAN

NORTH

1/4" = 1'-0"

2' 4' 8' 12'

GENERAL SHEET NOTES

SHEET KEYNOTES

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:0

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

EG101

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

G

RO

UN

DI

NG

A

ND

L

IG

HT

NI

NG

P

RO

TE

CT

IO

N

PL

AN

KB

12894135

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

EG

1 NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

1/4" = 1'-0"A3 GROUND LEVEL - GROUNDING PLAN

1. PROVIDE #2/0 AWG BARE COPPER GROUND LOOP CONDUCTOR INSTALLED

AT APPROXIMATELY 3'-0" OUT FROM THE EXTERIOR WALL AT 36" BELOW

GRADE.

2. PROVIDE GROUND ROD WITH TEST PIT ENCLOSURE WITH MECHANICAL

HIGH STRENGTH CABLE CONNECTORS FOR SYSTEM TESTING.

3. BOND THE BUILDING REBAR TO SECONDARY GROUND LOOP WITH A #2/0

AWG BARE COPPER BONDING CONDUCTOR.

4. PROVIDE MAIN ROOF CONDUCTOR INTERCONNECTING THE AIR

TERMINALS.

5. PROVIDE DOWN CONDUCTOR FROM AIR TERMINAL IN A 1" SCHEDULE 80 PVC

CONDUIT DOWN TO 18" BELOW GRADE TO THE TEST WELL SHOWN ON THIS

SHEET.

6. PROVIDE #2/0 AWG BARE COPPER BONDING CONDUCTOR FROM GROUND

BAR TO SECONDARY GROUND LOOP.

7. NEC REQUIRED SERVICE GROUND ROD.

8. BOND PLUMBING VENT TO LPS.

2 (TYP)

1/4" = 1'-0"A1 ROOF LEVEL - LIGHTNING PROTECTION PLAN

4 (TYP)

MGB

A. REFER TO SHEETS E-001 THROUGH E-004 FOR ADDITIONAL ELECTRICAL

INFORMATION.

B. PROVIDE CLASS 1 LIGHTNING PROTECTION SYSTEM. PROVIDE #2/0AWG

BARE COPPER CONDUCTOR WITH STRANDS NOT LESS THAN #17AWG FOR

MAIN ROOF LPS AND DOWN CONDUCTORS.

C. EXTERIOR CONDUCTORS WITHIN 8 FEET OF PAVEMENT MUST BE

PROTECTED IN 1" SCHEDULE 80 PVC CONDUIT.

SY

M

DE

SC

RI

PT

IO

N

DA

TE

OS

3D

O

3D

ELECTRICAL

GATE / SENTRY HOUSE

TOILET

PLUMBING

B

A

C2E

C2

D6E

P4E

P4

P4

W1E

W1E

W1E

W1E

1(TYP)

X2

HP-SB: 3

P2

2(ON ROOF)

LTG CONTROLS

R1

PLAN

NORTH

1/4" = 1'-0"

2' 4' 8' 12'

GENERAL SHEET NOTES

SHEET KEYNOTES

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:0

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

EL101

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

L

IG

HT

IN

G

P

LA

N

KB

12894136

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

EL

1 NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

1/4" = 1'-0"A3 LIGHTING PLAN

A. REFER TO SHEETS E-001 THROUGH E-004 FOR ADDITIONAL ELECTRICAL

INFORMATION.

B. REFER TO LIGHTING FIXTURE AND CONTROLS SCHEDULE ON SHEET E-701

FOR ADDITIONAL INFORMATION.

C. PROVIDE UNSWITCHED HOT LEG TO EXIT SIGNS.

1. PROVIDE PHOTOCELL MOUNTED ON ROOF FACING NORTHERN SKY FOR

CONTROL OF EXTERIOR WALLPACKS.

2. PROVIDE PHOTOCELL MOUNTED ON ROOF FACING NORTHERN SKY FOR

CONTROL OF MAGAZINE AREA POLE LIGHTS. REFER TO SITE PACKAGE FOR

POLE LIGHT LOCATIONS AND LIGHTING CONTROL SEQUENCE OF

OPERATION.

SY

M

DE

SC

RI

PT

IO

N

DA

TE

AT

S

T3

JB

JB

JB

JB

GATE / SENTRY HOUSE

ELECTRICAL

TOILET

FR

ON

T

ATS PULLBOX

GFI

PLUMBING

B

A

MDP

ATS-1

T-LP-SB

LP-SB

LTG CONTROLS

GFI

WP-WIN

GFI

WP-WIN

MDP-SB 3

LP-SB: 1

LP-SB: 1

LP-SB: 1

LP-SB: 2

LP-SB: 2

LP-SB: 3

LP

-S

B:

3LP-SB: 4

LP-SB: 5

LP-SB: 6

LP-SB: 8

LP-SB: 8

LP-SB: 7,9

MAIN GROUND BAR

LP-SB: 21

HP-SB

GFI

LP-SB: 25

GFI

LP-SB: 27

LP-SB: 5

METERING, SPD,

AND MCB

COMPARTMENT

B

A

DHWH-1

GATE / SENTRY HOUSE

TOILET

PLUMBING

ELECTRICAL

CU-2CU-1

ERV-1

AC-11

AC-2 1

UH-1

UH-2

PLAN

NORTH

1/4" = 1'-0"

2' 4' 8' 12'

GENERAL SHEET NOTES

SHEET KEYNOTES

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:0

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

EP101

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

P

O W

ER

A

ND

E

Q

UI

PM

EN

T

PO

W

ER

P

LA

N

KB

12894137

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

EP

1 NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

1/4" = 1'-0"A3 POWER PLAN

1/4" = 1'-0"A1 EQUIPMENT POWER PLAN

A. REFER TO SHEETS E-001 THROUGH E-004 FOR ADDITIONAL ELECTRICAL

INFORMATION.

B. REFER TO EQUIPMENT CONNECTION SCHEDULE ON THIS SHEET FOR

ADDITIONAL CIRCUITING AND DISCONNECTING MEANS INFORMATION.

1. UNIT IS POWERED BY CORRESPONDING OUTDOOR UNIT. PROVIDE WIRING

FROM OUTDOOR UNIT TO INDOOR UNIT AS RECOMMENDED BY EQUIPMENT

MANUFACTURER. PROVIDE 30A NON-FUSED DISCONNECT SWITCH IN NEMA

1 ENCLOSURE.

2. PROVIDE JUNCTION BOX AND HARDWIRED CIRCUIT FOR SENSOR OPERATED

CONTROLS FOR EVERY PLUMBING FIXTURE LOCATED IN RESTROOM.

3. PROVIDE 120V HARDWIRED CIRCUIT FOR ELECTRONIC TRAP PRIMER.

4. PROVIDE NEMA L6-30R FOR TELECOM RACK POWER. PROVIDE 2#10 + 1#10G

IN 3/4"C.

5. PROVIDE 120V HARDWIRED CIRCUIT FOR SECURITY PANEL POWER.

6. SWITCHBOARD WIDTH MUST NOT EXCEED 6'-0".

7. PROVIDE RECEPTACLE FOR REMOTE WATER METER DISPLAY.

8. PROVIDE GENERATOR ANNUNCIATOR PANEL.

9. PROVIDE DEDICATED QUAD RECEPTACLE FOR TELECOM RACK POWER.

10. COORDINATE FINAL LOCATION OF MANUFACTURER PROVIDED DISCONNECT

SWITCH. MAINTAIN NEC CLEARANCES.

11. COORDINATE FINAL LOCATION OF CEILING MOUNTED RECEPTACLE FOR

ERV-1 WITH EQUIPMENT SUPPLIER.

12. LOCATE DISCONNECT SWITCH FOR DHWH-1 BELOW SINK.

MECHANICAL EQUIPMENT CONNECTION SCHEDULE

TAG DESCRIPTION LOCATION VOLTAGE PHASE kVA FLA SETS WIRE AND CONDUIT CIRCUIT LOCAL DISCONNECTING MEANS TYPE

DISCONNECT

RATING

DISCONNECT

ENCLOSURE

CU-1 CONDENSING UNIT EXTERIOR 208 1 3 15.2 1 2 - #10 + #10N + #10G IN 3/4"C LP-SB: 11,13 FACTORY MOUNTED AND WIRED FUSED DISCONNECT SW. NA NA CU-2 CONDENSING UNIT EXTERIOR 208 1 2 8.8 1 2 - #12 + #12N + #12G IN 3/4"C LP-SB: 14,16 FACTORY MOUNTED AND WIRED FUSED DISCONNECT SW. NA NA DHWH-1 HOT WATER HEATER TOILET 002 208 1 4 20.0 1 2 - #10 + #10G IN 3/4"C LP-SB: 10,12 NONFUSED ENCLOSED ROTARY DISCONNECT SW. 30A NEMA 1 ERV-1 ENERGY RECOVERY VENTILATOR GATE/SENTRY HOUSE 001 120 1 0 0.4 1 1 - #12 + #12N + #12G IN 3/4"C LP-SB: 15 CEILING MOUNTED DUPLEX RECEPTACLE NA NEMA 1 UH-1 ELECTRIC UNIT HEATER TOILET 002 208 1 2 7.2 1 2 - #12 + #12G IN 3/4"C LP-SB: 17,19 INTEGRAL UNIT MOUNTED SWITCH BY MANUFACTURER NA NEMA 1 UH-2 ELECTRIC UNIT HEATER PLUMBING 004 208 1 2 7.2 1 2 - #12 + #12G IN 3/4"C LP-SB: 18,20 INTEGRAL UNIT MOUNTED SWITCH BY MANUFACTURER NA NEMA 1

SY

M

DE

SC

RI

PT

IO

N

DA

TE

CONNECTOR,

CONDUCTORS TO

GROUND ROD

CONCRETE COVER

W/RECESSED HANDLE

9"

2'- 0"

VITRIFIED CLAY

PIPE, 12" I.D.

#2/0 BARE

COPPER

GROUND ROD

EXOTHERMIC

CONNECTION

3/4" X 10'-0" COPPER CLAD STEEL

GROUND ROD

#2/0 BARE STRANDED

COPPER GROUND CONDUCTOR

BURIED 36" BELOW GRADE.

EXOTHERMIC CONNECTION. APPLY 1/2 LAPPED

STRIP INSULATION BACK TO PERFORM LAYER

OF RUBBER TAPE AND 1/2 LAPPED LAYER OF

PVC ELECTRICAL TAPE TO PREVENT

CORROSION OF CONNECTION.

ADHESIVE BASE

ADHESIVE TYPE

CABLE FASTENER

AIR TERMINAL 24"

SLOPING TPO ROOF

COPPER CABLE TO OTHER

TERMINALS OR DOWN

CONDUCTORS

LIGHTNING PROTECTION AIR TERMINAL

BLUNT TIP TYPE

PRIMARY DOWN CONDUCTOR IN 1"

SCHEDULE 80 PVC CONDUIT ROUTED

ON SIDE OF EXTERIOR FACADE

GRADE

PRIMARY RING CONDUCTOR #2/0 AWG

BARE STRANDED COPPER

GROUND ROD

BOLTED CLAMP

CONNECTION TO

GROUND ROD IN TEST

WELL

'-0

" M

IN

3'- 0"

MI

N

3'-0"MIN

3'-0"

3 3 /4"

1/4

1"

1" 4"∅5/16" ∅7/16"

MI

N

TOP VIEW

FRONT VIEW

FLOOR

STAINLESS STEEL

MOUNTING BOLT

COPPER BUS BAR

THERMOSET POLYESTER

SHATTER RESISTANT

INSULATOR AND WALL

BRACKET (AS NEEDED)

WALL

ANCHOR COMPATIBLE

FOR WALL TYPE

NOTES:

1. PROVIDE WALL MOUNTED NAMEPLATE

INDICATING GROUND BAR IDENTITY 12 INCHES ABOVE

GROUND BAR. SEE GROUNDING PLAN FOR GROUND

BAR IDENTITIES.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:4

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-501

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

D

ET

AI

LS

KB

12894138

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -5

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

NTSA2 GROUND TEST WELL

NTSA1 GROUND ROD DETAIL

NTSA3 LIGHTNING PROTECTION AIR TERMINAL

NTSB1 TYPICAL ELECTRICAL DOWN CONDUCTOR DETAIL

NTSB3 MAIN GROUND BAR (MBG) DETAIL

SY

M

DE

SC

RI

PT

IO

N

DA

TE

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:5

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-502

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

D

ET

AI

LS

KB

12894139

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -5

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

SY

M

DE

SC

RI

PT

IO

N

DA

TE

LSIG

1600 AF

1600 AT

SWBD MDP

1600A, 480Y/277V, 3 PHASE, 4 WIRE

SERVICE

ENTRANCE RATED

L S P

G

T-UTILITY-SB

1500 KVA

13200 V- 480/277 V

STANDBY GENERATOR GEN-1

750KW/937.5KVA

480Y/277V, 3 PHASE, 4 WIRE

WITH 48 HOUR SUB-BASE FUEL TANK

120Y

ATS-1

480Y/277V,1200A, 65kAIC

3 PHASE, 4 WIRE, 4-POLE

WITH ISOLATION BYPASS

50 kA WCR 160S

200 AF

125 AT

TO TYPE H-001 MAG

480Y/277V PNL

13S

200 AF

125 AT

TO TYPE G-002 MAG

480Y/277V PNL

200 AF

125 AT

TO TYPE G-001 MAG

480Y/277V PNL

100 AF

70 AT

TO EX. TOMAHAWK

BLDG A113

120/240V PNL

225 AF

150 AT

TO EX. MK-48

BLDG A114

208Y/120V PNL

15S 7S

11 2

EX.

75 KVA

480 V- 208/120 V

SPDSPD SPD

DM

LSIG

1200 AF

1200 AT

SWBD MDP-SB

1200A, 480Y/277V, 3

PHASE, 4 WIRE

600 AF

250 AT

TO CLWS#6 MAG

480Y/277V PNL

600 AF

250 AT

TO CLWS#5 MAG

480Y/277V PNL

400 AF

250 AT

TO CLWS#4 MAG

480Y/277V PNL

400 AF

250 AT

TO CLWS#3 MAG

480Y/277V PNL

400 AF

250 AT

TO CLWS#2 MAG

480Y/277V PNL

400 AF

250 AT

TO CLWS#1 MAG

480Y/277V PNL

150 AF

60 AT

T-LP-SB

30 KVA

480 V- 208/120 V

PANEL LP-SB

208Y/120V

3 3 3 3 3 3

4 (TYP)

SPD SPD SPD SPD SPD SPD

LSIG

1200 AF

1200 AT

SPD

LSI

1200 AF

1200 AT

120Y

120Y

7Y

3P

3P

3P3P3P2P3P3P

3P

3P 3P 3P 3P 3P 3P 3P 150 AF

60 AT 3P

PANEL HP-SB

480Y/277V

T-A113

25KVA

480V - 120/240V

10 10 10 10 10 10 7Y

13S13S

51S 51S 51S 51S 62S 62S

150 AF

30 AT 3P

3Y

SPD

7S

15S

13Y

GENERAL SHEET NOTES

SHEET KEYNOTES

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P

AR

TM

E

N T

O F

TH

E

N A

VY

N

A

VA

L

FA

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S

YS

TE

M

S C

O M

M A

N D

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

AS NOTED

1100 NORTH GLEBE ROAD

SUITE 500

ARLINGTON, VIRGINIA 22201

571.218.1000

FAX: 571.218.1600

6/

/2

5:

:5

PM

\\d c1 vs

\fe dp rj\

FD

ZE

\E

LE

C

\B

LD

G -1

-E

-B

IM

_S

EN

TR

Y_ v2 1.

rv t

E-601

P-

W

EA

PO

NS

M

AG

AZ

IN

E

OR

DN

AN

CE

O

PE

RA

TIO

NS

F

AC

ILI

TY

EL

EC

TR

IC

AL

P

O W

ER

S

IN

GL

E

LI

NE

D

IA

G

RA

M

KB

12894140

JHP JHP

05/27/2025

APPROVED BY LCDR ELIZABETH

OLOKODE NAVFAC NLON FEAD

DIRECTOR NEW LONDON, GROTEN, CT

SE

NT

RY

SMS/CWJ

1667770

GR

OT

ON

, C

ON

NE

CT

IC

UT

NA

VA

L S

UB

MA

RI

NE

B

AS

E

NE

W

LO

ND

ON

JWJ

WRB

HPN

M

ID

-A

TL

A N

TI

C

E -6

NA

VA

L

FA

CI

LI

TI

ES

E

NG

IN

EE

RI

NG

S

YS

TE

M

S

CO

M M

AN

D

-M

ID

-A

TL

AN

TI

C N

A

VA

L S

TA

TI

O N

N

O R

FO

LK

, V A

NTSA1 SINGLE LINE DIAGRAM - SENTRY BUILDING

A. REFER TO SHEETS E-001 THROUGH E-004 FOR ADDITIONAL ELECTRICAL

INFORMATION.

B. REFER TO SHEET E-703 FOR FEEDER SCHEDULE.

C THE STANDBY POWER SYSTEMS MUST MEET THE REQUIREMENTS OF NEC

ARTICLE 702, OPTIONAL STANDBY.

1. REFER TO TYPE G MAGAZINE SITE-ADAPTED ELECTRICAL DRAWINGS

FOR ADDITIONAL INFORMATION.

2. REFER TO TYPE H MAGAZINE SITE-ADAPTED ELECTRICAL DRAWINGS

FOR ADDITIONAL INFORMATION.

3. REFER TO TYPE CLWS BOX MAGAZINE SITE-ADAPTED ELECTRICAL

DRAWINGS FOR ADDITIONAL INFORMATION.

4. DISCONNECT WITH INTEGRAL SURGE PROTECTIVE DEVICE SHOWN IS

LOCATED ON EXTERIOR WALL OF ASSOCIATED MAGAZINE. REFER TO

RESPECTIVE MAGAZINE TYPE SITE-ADAPTED ELECTRICAL DRAWINGS FOR

ADDITIONAL INFORMATION.

5. MV FEEDERS TO UTILITY TRANSFORMER. REFER TO ELECTRICAL SITE

PACKAGE FOR ADDITIONAL INFORMATION.

6. PROVIDE 100% RATED BREAKER.

7. PROVIDE 60A MCB, 208Y/120V, 3-PHASE, 4-WIRE PANELBOARD "GEN" INSIDE

GENERATOR ENCLOSURE AND FEED FROM PANELBOARD LP-SB. REFER

TO SHEET E-702 FOR ADDITIONAL INFORMATION REGARDING GENERATOR

APPURTENANCE CIRCUITS. COORDINATE WITH GENERATOR

MANUFACTURER FOR FINAL SIZE REQUIRED OF APPURTENANCES AND

ADJUST CIRCUIT SIZE ACCORDINGLY.

8. PROVIDE CONTROL AND ANNUNCIATOR WIRING IN 1"C BETWEEN

AUTOMATIC TRANSFER SWITCH AND GENERATOR FOR GENERATOR AUTO-

ON SIGNAL.

9. PROVIDE INTEGRAL SURGE PROTECTIVE DEVICE IN MAIN SWBD MDP-1.

10. FEEDERS ARE UPSIZED TO ACCOUNT FOR VOLTAGE DROP TO CLWS

MAGAZINES.

11. PROVIDE #3/0 GEC.

12. PROVIDE SPD AT ATS.

13. BOND GENERATOR NEUTRAL TO GROUND BUS TO CREATE SEPARATELY

DERIVED SYSTEM FOR USE WITH 4-POLE ATS. GENERATOR MUST BE

SOLIDLY GROUNDED.

14. PROVIDE REMOTE EMERGENCY OFF BUTTON AT GENERATOR ENCLOSURE.

15. PROVIDE TRANSFORMER IN NEMA 4X ENCLOSURE, RATING AS SHOWN AT

EXISTING MAGAZINE NOTED. PROVIDE #6AWG GEC. TRANSFORMER IS

LOCATED OUTSIDE OF EXISTING MAGAZINE. REFER TO ELECTRICAL SITE

PACKAGE FOR EQUIPMENT LOCATION.

16. PROVIDE ELECTRONIC TRIP TYPE CIRCUIT BREAKER.

17. PROVIDE 600V, 100A, 2P NONFUSED DISCONNECT SWITCH IN NEMA 4X

ENCLOSURE. SWITCH IS LOCATED OUTSIDE OF EXISTING MAGAZINE.

REFER TO ELECTRICAL SITE PACKAGE FOR EQUIPMENT LOCATION.

18. REMOVE AND REPLACE EXISTING FEEDER FROM TRANSFORMER

SECONDARY SIDE TO EXISTING DISCONNECT SWITCH SERVING THE

EXISTING MAGAZINE. CONDUIT AND CONDUCTOR SIZE MUST MATCH

EXISTING.

19. PROVIDE 600V, 200A, 3P NONFUSED DISCONNECT SWITCH IN NEMA 4X

ENCLOSURE. SWITCH IS LOCATED OUTSIDE OF EXISTING MAGAZINE.

REFER TO ELECTRICAL SITE PACKAGE FOR EQUIPMENT LOCATION.

20. PROVIDE #6 GEC.

21. PROVIDE INTEGRAL DIGITAL METERING IN MAIN SWBD MDP-1. METER MUST

BE EIG SHARK 270. COORDINATE WITH SWBD MANUFACTURER TO PROVIDE

ALL NECESSARY CT'S AND OTHER ACCESSORIES NEEDED FOR PROPER

FUNCTION.

22. REFER TO SHEET ES103 ON THE ELECTRICAL SITE PACKAGE FOR LOCATION

OF GENERATOR.

SY

M

DE

SC

RI

PT

IO

N

DA

TE

LIGHTING CONTROL MATRIX

MA

NU

AL

O

N

SPACE TYPE MA

NU

AL

O

FF

MA

NU

AL

A

DJ

US

T

TIM

ER

O N

OC

CU

PA

NC

Y

ON

TO

0%

OC

CU

PA

NC

Y

ON

TO

VA

CA

NC

Y

OF

F

VA

CA

NC

Y

TO

DA

YL

IG

HT

A

DJ

US

T

PH

OT

OC

EL

L O N

PH

OT

OC

EL

L O

FF

SE

QU

EN

CE

O F O

PE

RA

TIO

N

ELECTRICAL / UTILITY ROOM

PRIVATE OFFICE

RESTROOM

EXTERIOR LIGHTING

NOTES

X X

X X

X X

X

MA

NU

AL

O

VE

RR

ID

E

TIM

ER

O

FF

X

X

X

X

SOO A

SOO B

SOO C

SOO D

SOO A

LINE VOLTAGE MANUAL ON/OFF CONTROLS ONLY.

SOO B

LIGHTS CONTROLLED BY LOCAL 3 BUTTON DIMMING SWITCH PROGRAMMED TO 0% / 50% / 100% LIGHT OUTPUT WITH RAISE LOWER OPTIONS. OCCUPANCY SENSOR MUST TURN LIGHTS OFF WHEN SPACE IS VACANT MORE THAN 15 MINUTES.

X

GATE/SENTRY HOUSE 001

TOILET 002

EXTERIOR BUILDING LIGHTING

ELECTRICAL 003, PLUMBING 004

SOO C

LIGHTS WILL TURN ON TO 100% LIGHT OUTPUT BY OCCUPANCY SENSOR AND TURN OFF WHEN SPACE IS VACANT MORE

THAN 15 MINUTES. LIGHTS MAY ALSO BE CONTROLLED BY MANUAL ON/OFF SWITCH.

SOO D

LIGHTS MUST TURN ON AT DUSK. AUTOMATICALLY REDUCE LIGHTING POWER BY A MINIMUM OF 30% FROM 12 MIDNIGHT OR WITHIN ONE HOUR OF NORMAL CLOSING, WHICHEVER IS LATER, UNTIL 6AM OR NORMAL OPENING, WHICHEVER IS EARLIER.

AUTOMATICALLY TURN OFF VIA PHOTOCELL WHEN SUFFICIENT DAYLIGHT IS AVAILABLE.

X

1. LIGHTING FIXTURES, INSTALLATION, SUPPORT, WIRING AND RELATED WORK MUST COMPLY WITH GENERAL NOTES, FIXTURE SCHEDULE, LAMP/DRIVER REQUIREMENT TABLES, FIXTURE DETAILS, SPECIFICATIONS AND CONTRACT DRAWINGS.

2. PROVIDE ACCESSORIES REQUIRED FOR A COMPLETE INSTALLATION AND COORDINATE WITH WORK BY OTHER TRADES. RECESSED FIXTURES MUST BE COMPLETELY SERVICEABLE FROM THE FIXTURE OPENING. PROVIDE REQUIRED MOUNTING HARDWARE, SUPPORTS, ACCESSORIES, AND TRIM REQUIRED FOR A COMPLETE INSTALLATION. COORDINATE FIXTURE MOUNTING WITH CEILING AND WALL CONSTRUCTION WHERE INSTALLED. PROVIDE SEPARATION BETWEEN RECESSED FIXTURES AND SURROUNDING INSULATION TO COMPLY WITH UL LISTING REQUIREMENTS AND MANUFACTURER

INSTRUCTIONS.

3. FIXTURES MUST BE CBM APPROVED, LISTED AND LABELED BY ETL OR UL FOR DRY, DAMP, WET OR HAZARDOUS/CLASSIFIED LOCATIONS FOR THE INSTALLATION, UNLESS MORE STRINGENT REQUIREMENTS

ARE INDICATED OR SPECIFIED.

4. DRIVERS MUST BE CBM APPROVED AND LISTED BY ETL OR UL. PROVIDE INTERNAL GREEN GROUNDING SCREW FOR FIXTURES.

5. WHERE EMERGENCY FIXTURES ARE UNSWITCHED, CONNECT EMERGENCY LIGHTING UNITS AND FIXTURES WITH EMERGENCY BATTERY PACKS TO PROVIDE ILLUMINATION AUTOMATICALLY UPON THE LOSS

OF NORMAL POWER. WHERE EMERGENCY FIXTURES ARE SWITCHED, UPON THE LOSS OF NORMAL UNSWITCHED POWER, THE EMERGENCY BATTERY PACK MUST PROVIDE ILLUMINATION AUTOMATICALLY

REGARDLESS OF SWITCH POSITION.

6. THE MANUFACTURERS AND MODELS LISTED ON THE LIGHTING FIXTURE SCHEDULE ARE LISTED TO INDICATE THE OVERALL LEVEL OF QUALITY…