Attachment_05_-_CAFB_Hardware_Specifications_Guideline_-_Nov_2016.pdf

CANNON AIR FORCE BASE

DOOR HARDWARE SPECIFICATION GUIDELINE

PERFORMANCE SPECIFICATION

SECTION 08 71 00

Edit Date: November 2016

For

Mr. Chris Jouett 109 Engineers Way

Cannon AFB, NM 88103

Attachment 5 FA4855-18-R-0003

CANNON AIR FORCE BASE

DOOR HARDWARE SPECIFICATION GUIDELINE

PERFORMANCE SPECIFICATION

SECTION 08 71 00

Edit Date: November 2016

The purpose of this booklet is to support the Cannon Air Force Base building standards for door hardware. The Base maintains the following hardware and is currently stocking replacement parts. The products listed in this booklet are to be used without substitution on new construction and modernization projects unless products are listed in this package as an alternate.

It is the intent of this booklet to provide guidelines for the architect's specification section 08 71 00, for product groups and the hardware schedule. It remains the architect's responsibility to coordinate these products to meet the applicable building codes, life safety codes, and ADA requirements.

Section 08 71 00 door hardware preamble must specify the following:

Door and frame prep Before hardware installation, verify that all doors and frames are properly prepared to receive the specified hardware. Hollow metal frames shall be prepared for ANSI strike plates per A115.1-2 (4-7/8" high), hinge preps will be mortised and reinforced with a minimum of 8 gauge reinforcement material for closer installation. Hollow metal doors shall be properly prepared and reinforced with a minimum of 16 gauge material for either mortised or cylindrical locks as specified. It is preferred that all hollow metal doors receiving door closers have 12 gauge reinforcement. If this is not possible, the use of sex bolts is mandatory.

Wood doors shall be factory prepared to receive the scheduled hardware.

Hardware installation The manufacturer's representatives shall make themselves available for inspection and/or approval, of the installation of their products upon request of the owner’s representative and/or architect. Hardware installed incorrectly must be reported to the architect prior to the architect's final punch list.

Specification Service J. Karen Hill, AHC/CDC, CSI, CDT 480.239.2424 Lise C Allard, AHC/CSI 602.684.7558 Copyright © 2001

SPECIFICATION GUIDELINE

Cannon Air Force Base - STANDARDS – Substitutions or Alternates not permitted

Edit Date: November 2016

DOOR HARDWARE

Description Manufacturer Model/Series Finish

Hanging Devices

All hinges provided shall be provided by one manufacturer. No exposed bearing raceways will be permitted. Hinge type, sizes and quantity per leaf shall be as per the manufacturer’s recommendations listed in the front of their catalogue. Doors requiring anti-friction hinges, including but not limited to Fire Doors, doors with self closing devices, entrance doors, and doors with high usage, shall use a concealed bearing system. The concealed bearing system utilized shall surpass the ANSI/BHMA A156.1 “Standard For Butts & Hinges” Grade 1 test criteria for all hinge sizes and weights (standard & heavy duty). All Concealed Bearing hinges shall be covered in writing by a Limited Lifetime Warranty guaranteeing the building owner that the product will not fail during the operational life of the building provided the manufacturer’s recommended installation instructions are followed.

Mortise Hinges Hager “Made in America” All Exterior Doors shall have Commercial Grade Heavy Duty Ball Bearing Non Removable Pin Hinges

All Interior High Traffic doors must have Commercial Grade Heavy Duty Ball Bearing Hinges (if swinging out

– must have non-removable pins)

All Interior Light Duty Doors shall have Commercial Grade Ball Bearing Hinges (if swinging out – shall have non-removable pins)

Alternate Bommer “Made in America”

Alternate Must be “Made in America”

Securing Devices Cylindrical lever type locksets must be extra heavy duty type with 2-3/4 inch backset, or greater as specified, with a 9/16 inch throw latchbolt. Provide locksets with 7-pin interchangeable core. Locksets and latchsets must conform to ANSI A156.2, Series 4000, Grade 1, and be UL listed. Locksets and cores to be of the same manufacturer to maintain complete lockset warranty. Locksets and latchsets with levers must fit modified ANSI A115.2 door preparation. Locksets to have anti-rotational studs that are thru-bolted. Keyed lever shall not have exposed “keeper” hole. Each lever to have independent spring mechanism designed to control the lever only. Outside lever sleeve to be seamless, of one piece construction, made of a hardened steel alloy. Keyed lever to be removable only after core is removed, by authorized control key, to allow access to knob “keeper”. Hub, side plate, anti-rotational studs to be a one-piece casting with a shrouded locking lug. Locksets outside locked lever must withstand 1400 inch pounds of torque. In excess of that, a replaceable part will shear, not allowing entry by lever.

Permanent core face must be the same finish as the lockset finish.

Edit Date: November 2016

DOOR HARDWARE

Description Manufacturer Model/Series Finish

Preferred Lock Set Best 9K Varsity Series 15D Trim 626

* Lock Function Room type 9K-AB Office 9K-AB Office 9K-C Communicating 9K-R Classroom 9K-D Storeroom 9K-D Storeroom 9K-OL Privacy

Faculty, Administration, Offices Entrance Communicating doors between rooms Conference Rooms.

Storage, Mech., Elect. rooms.

Maintenance, Closets Bathroom

*FINAL DECISIONS AS TO FUNCTIONS OF LOCKSETS PER ROOM TYPE WILL BE

DETERMINED BY OWNER

Alternate No Substitute

Cylinders: Best 1E72 Rim Cylinders 626 1E74 Mortise Cylinders 626

Auxiliary Locks Best 83T-S or 48H7R Bathroom (Exterior/Interior) (Used with Push/Pull) 626

Key System Best Removable/Interchangeable Core 626 7-pin PATENTED CORMAX MX8 Keyway

KEYS ARE THE PROPERTY OF THE GOVERNMENT

Provide construction cores and keys during the construction period. Construction control and operating keys and cores shall not be part of the Owner’s permanent keying system or furnished on the same keyway (or key section) as the Owner’s permanent keying system.

Permanent cores and keys (prepared according to the accepted keying schedule) will be furnished to the Owner. All cylinders shall be 7-pin Patented Cormax MX8 keyway, interchangeable core. Permanent keys and cores shall be stamped with the applicable key mark for identification. These visual key control marks or codes will not include the actual key cuts. Permanent keys will also be stamped “Do Not Duplicate.” Grand Masterkeys, Masterkeys and other Security keys shall be transmitted to the Owner by Registered Mail, return receipt requested.

SHIP CORES & KEYS TO:

LOCKSHOP Mr. Chris Jouett 506 Air Commando Way Cannon AFB, NM 88103

Edit Date: November 2016

DOOR HARDWARE

Description Manufacturer Model/Series Finish

2 each Operating Keys per Lock “Fed Gov Property” 4 each Control Key 9 each Construction Operating Keys 4 each Construction Control Keys 20 each Additional Cores 5 each Padlocks 41B772L WC 1 each Key Cabinet 10% expansion x Best MX8

Alternate No Substitution

Padlocks Best 41B772L WC

Sesamee Combination Padlocks

Exit Device Precision 2103 x 1703Ax SN rim device 630 FL2108 x V4908A SN Fire rated rim device 630 On pairs of Exterior doors, use key removable mullion KR822 with one 2101 SN and one 2103 x 1703A SN On pairs of Fire rated doors, use key removable mullion KR822 with one FL-2101 SN and one FL-2108 x

V4908A SN

On pairs of doors where Vertical Rods are being used, use surface 2200 series less bottom rods on non exterior openings.

Coordinator Trimco 3094 x 3090 Brackets (as required) 626

• Use coordinator where required by fire code Such as Pairs of Rated doors to Mechanical Rooms where locks are used.

Flush Bolts Trimco 3810 Automatic for metal doors 626 3815 Automatic for wood doors 626 3915 Manual for metal doors(Storage/Utility)626 3913 Manual for wood doors 626 Use automatic flush bolts where required by fire code

Edit Date: November 2016

DOOR HARDWARE

Description Manufacturer Model/Series Finish

Closing Device

Closer LCN 4040 EDA 689

• Delayed Action Arm, Stop Arm, Compression

• Hold Open Arms on all non-rated doors

• All door frames to be reinforced

Alternate Stanley D4550 EDA 689

• Delayed Action Arm, Stop Arm, Compression

• Hold Open Arms on all non-rated doors

• All door frames to be reinforced

**ADA Operators

NABCO-GYROTECH

Low Energy Heavy Duty Operator Existing Doors to have Radio Frequency Actuators

**FINAL DECISIONS AS TO LOCATION WILL BE DETERMINED BY OWNER

Stops & Holders

Magnetic Holders Rixson 990 Series 630 Concealed wiring where possible

Overhead Holder ABH Preferred where possible 4000Series (36” +) Overhead concealed

Heavy Duty 630

Door Stops Trimco 1270CX /1270CV Wall stop (Interior Concrete Wall) 630 1210 Interior floor 626 1209 Exterior floor BLK 1220-5 Door Holder (non rated doors) 626

• Allow for maximum swing of doors

• Backing required at wall stops

Edit Date: November 2016

DOOR HARDWARE

Description Manufacturer Model/Series Finish

Figure A Figure B

Future Electronic Access On Main Exterior Doors of each Buildings, Double Door Frames must be supplied with conduit in accordance with Figure A. Single Door Frames must be supplied with conduit in accordance with Figure B.

Barracks On Barracks, use Battery Operated Card Readers with Audit Trails, BASIS G (with audit trails)

45HG7TV-15MS-626 – MX8

to include the following parts:

SES-NETBOOK

SES-USB

SES-MEM

SES-DB9CON

S3K-IDEXPRESS-K-SWS

NTDMSR20633BA

BASD-CAB

VPA-PVC (500)

VPD-CLN

Encoder KIOSK Card Management Encoding System

Alternate – NO SUBSTITUTION

Edit Date: November 2016

DOOR HARDWARE

Description Manufacturer Model/Series Finish

. Hangers and Com Rooms

EZ Keypads (no audit trails) 93KZ7DV-15PK S3 626 SH

Accessories

Kick Plate Trimco Locker Rooms shall have kick plates on both Side of doors KO050 10”x2”LDW x .050” Thick x B3E (sgl.door) 630 KO050 10”x1” LDW x .050” Thick x B3E (pr.doors) 630

Push / Pull Plate Trimco 1001-3-8 / or / 4x16 (CFC where required) 630

Lock Protector Trimco 5002 630

Threshold Pemko 172A/171A (1/2” Saddle threshold) 628

• Architect to coordinate with project conditions

Weather Seal Pemko 309AP or 315CR (at head and jambs ) 628 57AV or 315CN (at sill on door – surface mount)

Door Silencers Trimco 1229A (Metal frames) Gray 1229B (Wood frames) Gray

Astragal Pemko 357C or 305CN

• Where required by fire code

• Astragal by door manufacturer at HM door.

Drip Guard Pemko 346C 4” ODW (Exterior doors exposed to rain) 628 www.hagerco.com

ARCHITECTURAL HINGES

FU

LL M

O R

TISE

FIVE KNUCKLE HINGES (CONTINUED)

BB1191

Ball Bearing - Standard Weight Brass with stainless steel pin (ANSI A2112) or stainless steel with stainless steel pin (ANSI A5112)

BB1279

Ball Bearing - Standard Weight Steel with steel pin (ANSI A8112)

• Two ball bearings

• Non-rising removable pin with button tip and plug

• 5” x 5” (127 mm x 127 mm) and 4-1/2” x 4-1/2” (114 mm x 114 mm) BB1279 available with two different leaf sizes

• 3-1/2” x 3-1/2” (89 x 89 mm) BB1279 available with reversible hole pattern

• For use on medium weight doors or doors requiring medium frequency service

Hinge Size Gauge of Metal

Hole Count

Screw Size

Inches mm Machine Wood

3-1/2 x 3-1/2 89 x 89 0.119 6 1/2 x 10-24 1 x 9

4 x 4 102 x 102 0.129 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 4 114 x 102 0.134 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 4-1/2 114 x 114 0.134 8 1/2 x 12-24 1-1/4 x 12

5 x 4 127 x 102 0.145 8 1/2 x 12-24 1-1/4 x 12

5 x 4-1/2 127 x 114 0.145 8 1/2 x 12-24 1-1/4 x 12

5 x 5 127 x 127 0.145 8 1/2 x 12-24 1-1/4 x 12

6 x 4-1/2 152 x 114 0.160 10 1/2 x 1/4-20 1-1/2 x 14

6 x 5 152 x 127 0.160 10 1/2 x 1/4-20 1-1/2 x 14

6 x 6 152 x 152 0.160 10 1/2 x 1/4-20 1-1/2 x 14

WTBB1191

Ball Bearing - Standard Weight - Wide Throw Brass with stainless steel pin (ANSI A2112) or stainless steel with stainless steel pin (ANSI A5112)

WTBB1279

Ball Bearing - Standard Weight - Wide Throw Steel with steel pin (ANSI A8112)

• Wide throw

• Two ball bearings

• Non-rising removable pin with button tip and plug

• For use on medium weight doors or doors requiring medium frequency service

Hinge Size Gauge of Metal

Hole Count

Screw Size

Inches mm Machine Wood

3-1/2 x 5 89 x 127 0.119 6 1/2 x 10-24 1 x 9

3-1/2 x 6 89 x 152 0.119 6 1/2 x 10-24 1 x 9

4 x 5 102 x 127 0.129 8 1/2 x 12-24 1-1/4 x 12

4 x 6 102 x 152 0.129 8 1/2 x 12-24 1-1/4 x 12

4 x 7 102 x 178 0.129 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 5 114 x 127 0.134 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 6 114 x 152 0.134 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 7 114 x 178 0.134 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 8 114 x 203 0.134 8 1/2 x 12-24 1-1/4 x 12

5 x 6 127 x 152 0.145 8 1/2 x 12-24 1-1/4 x 12

5 x 7 127 x 178 0.145 8 1/2 x 12-24 1-1/4 x 12

5 x 8 127 x 203 0.145 8 1/2 x 12-24 1-1/4 x 12

Attachment 5 FA4855-18-R-0003

LMH0114

Line www.hagerco.com16

ARCHITECTURAL HINGES

FU

LL

M O

R

TI

SE

FIVE KNUCKLE HINGES (CONTINUED)

BB1168

Ball Bearing - Heavy Weight Steel with steel pin (ANSI A8111)

BB1199

Ball Bearing - Heavy Weight Brass with stainless steel pin (ANSI A2111) or stainless steel with stainless steel pin (ANSI A5111)

• Four ball bearings

• Non-rising removable pin with button tip and plug

• 5” x 5” (127 mm x 127 mm) and 4-1/2” x 4-1/2” (114 mm x 114 mm) BB1168 available with two different leaf sizes

• For use on heavy weight doors or doors requiring high frequency service

Hinge Size Gauge of Metal

Hole Count

Screw Size

Inches mm Machine Wood

4-1/2 x 4 114 x 102 0.180 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 4-1/2 114 x 114 0.180 8 1/2 x 12-24 1-1/4 x 12

5 x 4 127 x 102 0.190 8 1/2 x 12-24 1-1/4 x 12

5 x 4-1/2 127 x 114 0.190 8 1/2 x 12-24 1-1/4 x 12

5 x 5 127 x 127 0.190 8 1/2 x 12-24 1-1/4 x 12

6 x 4-1/2 152 x 114 0.203 10 1/2 x 1/4-20 1-1/2 x 14

6 x 5 152 x 127 0.203 10 1/2 x 1/4-20 1-1/2 x 14

6 x 6 152 x 152 0.203 10 1/2 x 1/4-20 1-1/2 x 14

8 x 6 203 x 152 0.203 16 1/2 x 1/4-20 1-1/2 x 14

8 x 8 203 x 203 0.203 16 1/2 x 1/4-20 1-1/2 x 14

WTBB1168

Ball Bearing - Heavy Weight - Wide Throw Steel with steel pin (ANSI A8111)

WTBB1199

Ball Bearing - Heavy Weight - Wide Throw Brass with stainless steel pin (ANSI A2111) or stainless steel with stainless steel pin (ANSI A5111)

• Wide throw

• Four ball bearings

• Non-rising removable pin with button tip and plug

• For use on heavy weight doors or doors requiring high frequency service

Hinge Size Gauge of Metal

Hole Count

Screw Size

Inches mm Machine Wood

4-1/2 x 5 114 x 127 0.180 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 6 114 x 152 0.180 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 7 114 x 178 0.180 8 1/2 x 12-24 1-1/4 x 12

4-1/2 x 8 114 x 203 0.180 8 1/2 x 12-24 1-1/4 x 12

5 x 6 127 x 152 0.190 8 1/2 x 12-24 1-1/4 x 12

5 x 7 127 x 178 0.190 8 1/2 x 12-24 1-1/4 x 12

5 x 8 127 x 203 0.190 8 1/2 x 12-24 1-1/4 x 12

Attachment 5 FA4855-18-R-0003

LMH0114

Line www.hagerco.com8

ARCHITECTURAL HINGES

G

EN

ER

A

L

IN

FO

R

M A

TI

O

N

BEARING OPTIONS

When using steel based hinges, special options are available such as stainless steel pins, stainless steel bearings and stainless steel raceways.

Ball Bearing (BB) - Ball bearings are engineered to throw the knuckle weight against specially hardened steel raceways, which ride on the bearing surfaces. The one-piece cup protects the bearings from moisture and dust. The cup supports no weight so it is not subjected to functional friction, pressure or wear. Lateral wear is minimized because the pin is held against thrust by the hardened steel top and bottom raceways.

The bearing units are securely press-fit to the leaf knuckle to prevent loss when the hinge is disassembled.

Oilite Bearings (OB) - The oilite bearing is made of porous metal that has been press-formed and impregnated with oil.

The slight pressure and heat generated when the door is operated causes the oil to come to the surface of the bearing causing the surface to be slick and smooth.

Anti-Friction Nylon Bearings (AB) - These are made of resilient engineering plastics that provide a self-lubricant and very strong bearing surface. The nylon acts as a cushion for the door yet it allows the door to flow smoothly on the surface of the nylon with an extremely low wear factor.

ARCHITECTURAL FINISH SyMBOLS Powder Coat Finishes

Note: Available only on architectural grade full mortise plain bearing hinges, full mortise ball bearing hinges, both standard and heavy weight, in both steel and brass material.

B.H.M.A. Symbol Base Material

*US3SC only available on AB800, AB850, and CB1191.

CARE AND MAINTENANCE

• Hinges must be free swinging without any binding. The use of shims to align hinges, if required, is satisfactory.

• Hinges should be well greased and checked on a regular basis for lubrication. We recommend that hinges used in commercial, high-frequency applications or those in extreme environmental conditions be lubricated annually to ensure quiet operation and long life.

• Standard hinges are best lubricated by removing the pin, applying a generous coating of lithium grease, and reinserting the pin by driving it completely down to the shoulder of the pin head.

• Hospital Tip (HT) hinges that have fixed hinge pins have an oil port on the knuckle for the purpose of lubrication.

• Water displacing sprays such as WD-40 are not recommended for hinge lubrication.

• To remove dirt, simply wipe with a soft damp cloth. Abrasive cleaners or lacquer thinner should not be used to clean the surface of hinges. To do so will void any warranty for the product.

Hager Description Steel Brass & Bronze

Stainless Steel

HEWI#

L1 Flat Black 693 693 N/A N/A

L2 Dark Bronze 695 695 N/A N/A

L3 Medium Bronze 694 694 N/A N/A

LS

Luma Sheen®

Aluminum Paint 689 689 N/A N/A

13P White N/A N/A N/A 1

14P Off White N/A N/A N/A 5A

15P Grey N/A N/A N/A 5

33P Yellow N/A N/A N/A 14

34P Red N/A N/A N/A 33

35P Green N/A N/A N/A 6

36P Blue N/A N/A N/A 52

83P Black N/A N/A N/A 8

84P Olive N/A N/A N/A 62

85P Brown N/A N/A N/A 9

86P Burgundy N/A N/A N/A 30

87P Dark Green N/A N/A N/A 60

88P Dark Blue N/A N/A N/A 50

Hager Description Steel Brass & Bronze

Series Stainless Steel

2C Plain Zinc Plate 603 N/A N/A

H2H Mechanical Galvanized; steel only

N/A N/A N/A

3 Bright Brass 632 605 N/A

3A Bright Brass - Unlacquered N/A N/A N/A

3SC*

Brass SecureCoat® Stainless Steel Lifetime Finish

N/A N/A N/A

4 Satin Brass 633 606 N/A

5 Satin Brass, Antique 638 609 N/A

9 Bright Bronze 637 611 N/A

9A Bright Bronze, No Lacquer N/A N/A N/A

10 Satin Bronze 639 612 N/A

10A Antique Bronze, Lacquered 641 N/A N/A

10B Antique Bronze, Oiled 640 613 N/A

10D Black Nickel, Oiled N/A N/A N/A

14 Bright Nickel 645 618 N/A

14B Black Nickel, Bright N/A N/A N/A

15 Satin Nickel 646 619 N/A

15A Antique Satin Nickel, Highlighted

647 620 N/A

17A Black Nickel, Dull 648 621 N/A

26 Bright Chromium Plated 651 625 N/A

26D Satin Chromium Plated 652 626 N/A

32 Stainless Steel Metal, Bright N/A N/A 629

32D Stainless Steel Metal, Satin N/A N/A 630

P Prime Coat 600 600 N/A

PS Plain Steel N/A N/A N/A

Attachment 5 FA4855-18-R-0003 www.hagerco.com

ARCHITECTURAL HINGES

G

EN

ER

A

L IN

FO

R M

A

TIO

N

Electric Hinges (Continued) Another important point to remember, an electrically modified hinge is for low voltage power transfer only (48 volts or under). Higher voltages are not allowed because of the potential dangers. Also a consideration is the Amperage rating of the power transfer hinges. Hager hinges include amperage ratings of 3.5 AMPS/continuous duty and 16.0 AMPS/ intermittent duty (pulse).

Normally, modifications are made to full mortise hinges. For other applications, consult Hager Engineering for availability.

It is recommended that the CENTER HINGE LOCATION be used with all electrically modified hinges.

Hager Companies recommends the use of a mortar box or jamb box in order to protect the wire terminations on the inside of the frame. If this box is not used, the grout that may be poured into the frame will destroy the wiring and usually void the warranty on the product.

Swaging Swaging is a slight offset of the hinge leaf at the barrel. This offset permits the leaves to come closer together when the door is in the closed position. If the hinge were to be left in the natural state after the knuckle was rolled, the hinge would be referred to as a “flatback”. A flatback hinge has a gap between the leaves of approximately 5/16” (7.9 mm). This would allow heat and air-conditioning to escape, not to mention the unsightly gap between the door and frame.

The swaging on standard weight and heavy weight full mortise hinges provides 1/16” (1.6 mm) clearance between the leaves when the leaves are in the closed position.

Full mortise hinges used on beveled doors will affect lockside clearance, especially for wide throw applications.

Security Features Three additional features that are commonly used are: Non- Removable Pin (NRP), Safety Stud (SH), and Reverse Security Stud (RSS). These features are intended as deterrents only.

Non-Removable Pin The Non-Removable Pin (NRP) has a small set screw in the body of the barrel. This set screw is tightened down against the pin.

The pin has a groove in the position where the set screw makes contact, allowing the set screw to seat. The set screw is positioned so it cannot be reached unless the door is opened. If pin removal is necessary, the set screw is merely removed and the pin tapped from the bottom in the usual manner.

Safety Stud The Safety Stud (SH) 3/16” (4.8 mm) projection is a feature that places a stud on one leaf and a locking hole on the other leaf.

When the door is closed, the stud is anchored into the opposite leaf. Even if the hinge pin is removed, the door is secure because the leaves are locked together.

Reverse Security Stud The Reverse Security Stud (RSS) 7/16” (11.1 mm) projection is a feature that has a stud projecting from the back of both leaves into the reinforcing plate of both the frame and the door. It is intended to keep the hinge locked in place from abuse of battering or trying to shear the hinge and screws.

This feature is primarily used in prisons and psychiatric areas.

E2 E1S E2/E1S Exposed Electric Hinge Modification

EMN ETW ETM

Concealed Electric Hinge Modification

Attachment 5 FA4855-18-R-0003

C Y

L

IN

D R

IC

A

L L

O C

K S

HEAVY DUTY LOCKS - LEVERS

2 H E AV Y D U T Y L

F E A

T U

R E S

TABLE OF CONTENTS

Features Specifications How to Order Trim Variations Options/Features Service Equipment

Function Descriptions . . . . . . . . . . . . . . . . . . . . . . . . .6-9 Shipping Weights 9K Sample Specifications Patented Keying Deadlocking Latches Strikes & Door Preparation

9K FEATURES

The innovative design of the slotted key release cam and locking lug assembly create maximum attack resistance. Amazingly, though damaged, the lock still allows key access. In addition, the lever is fully functional from the inside.

The hub-mounted torsion spring and strong retractor springs help prevent lever sag and offer a smooth and snappy operation.

Strong retractor springs provide resistance to lever sag.

Strong through-bolt mounting studs increase torque resistance.

Heavy rose liner material is highly attack resistant.

The outside lever sleeve is a seamless one piece construction made of a hardened steel alloy that provides additional reinforcement in the locking lug slot.

For versatile applications, lever by knob trim variations are available.

Interchangeable core allows for quick re-keying and customized masterkeying.

Lost Motion feature available allowing lever movement between 45º – 60º without engaging retractor assembly.

No exposed keeper hole in exterior lever -adds security.

New zinc hubs with a shrouded locking lug, guaranteeing higher quality and increased torque resistance.

Rose locking pin and rose assembly design offers great torque resistance.

It prevents the locking pin from twisting, bending, or breaking under attack.

Page Page

T A

B L E O

F C

O N

T E N

T S

O C K - L E V E R S 3

14– curved return

15– contour angle return

16– curved no return

Certifications– UL Listed:

Listed by Underwriter's Laboratories for use on 3 Hr, A label single swinging doors (4'x10'). GYJT Builders Hardware-single point locks or latches.

American National Standard: ANSI A156.2, Series 4000 Grade 1 (formerly FF-H-106C Series 161.)

Finish– BHMA US DESCRIPTION 605 3 bright brass 606 4 satin brass 611 9 bright bronze 612 10 satin bronze 613 10B oxidized satin bronze, oil rubbed 618 14 bright nickel plated 619 15 satin nickel plated 622 19 flat black 625 26 bright chromium plated 626 26D satin chromium plated 690 20 dark bronze

Backset– 2 3/4" standard, 3 3/4" and 5" available.

Chassis– Critical latch and chassis components are brass or corrosion-treated steel. 2 1/16" diameter to fit 2 1/8" hole in door (Conforms to ANSI A115.2). Lost Motion feature available as an option.(see page 11 for special features)

Door thickness– Available for 1 3/4" to 2 1/4" doors.

Spacers available for 1 3/8" doors.

UL Listed for both Canada and the US.

Latch– Solid brass 9/16" throw. Front 2 1/4" x 1 1/8" beveled.

Lever handles– Lever handles are a high-quality zinc alloy. Trim components are brass or bronze.Body is approximately 1 5/8" in diameter; Handle is approximately 4 3/4" long (from center-line of chassis). #14 and #15 levers conform to California Administrative Code Title 19 and Title 24. All three styles of levers conform to the Illinois Accessibility Standard.

Mounting– In addition to standard door preparation (ANSI A115.2 for 1 3/4" doors), two additional holes are needed for through-bolts. Through-bolts require two 5/16" diameter holes located at 12 o'clock and 6 o'clock positions. A drill jig is provided to insure accuracy of the holes. (see KD303 on back page).

Projection on door– Approximately 2 3/4" when mounted on 1 3/4" door.

Roses– C - 3" Convex D - 3 1/2" Convex K - 3" Convex - no ring L - 3 1/2" Convex - no ring

Strike– STK: Conforms to ANSI A115.2 (2 3/4" x 1 1/8" with curved lip & box). S3: Conforms to ANSI A115.2 for 1 3/4" doors (4 7/8" x 1 1/4" with curved lip).S3-7/8: Conforms to ANSI A115.2 for 1 3/4" doors (4 7/8" x 1 7/8" flat)

Products protected by one or more of the following patents:

U.S.: Canada:

D290,085 4,437,695 4,428,212 1,184,773 4,843,852 4,318,558 4,428,570 1,194,057 4,262,507 4,496,178 4,779,908 1,229,358 5,116,170 Other products patent pending.

S P

E C

IF

IC

A T

IO

N S

* Handles are made from a zinc alloy, and have been plated to be equivalent in appearance to the finishes listed.

For information on 9K non IC products please refer to Best’s non-IC keying products brochure.

pages 4-5 page 11pages 6-9

AL– abrasive lever LL– lead lined LM– lost motion RQE– request to exit SH– security head screws TL– tactile lever 3/4– 3/4" throw latch 7/8" LTC– flat lip strike NOTE: specify inside (I), outside (O), or both (B) for AL,TL options

Options

605 606 611 612 613 618 619 622 625 626

93K 7 AB 15 D S3 626

Backset Core

Housing Function

Code Lever Style

Rose Style

C– 3" convex D– 3 1/2" convex K– 3" convex

- no ring L– 3 1/2" convex -no ring

Strike Package

STK– 2 3/4"

ANSI

S3– 4 7/8"

ANSI

S3– 7/8- 7/8" flat strike

Available Finishes*

HOW TO ORDER

SPECIFICATIONS

H O

W T

O O

R D

E R pages 4-5 page 5

93K– 2 3/4" 94K– 3 3/4" 95K– 5"

0– keyless 7– 7 pin housing accepts all Best cores

AB– entrance D– storeroom L– privacy N– passage R– classroom Etc.

Attachment 5 FA4855-18-R-0003

L M HAMPTON

4 H E AV Y D U T Y L

T R

IM

V

A R

IA

T

IO

N S

D

IM

E N

S

IO

N S

TRIM VARIATIONS

LEVER & TRIM DIMENSIONS

14C 15C 16C

14D 15D 16D

14K 15K 16K

14L 15L 16L

Attachment 5 FA4855-18-R-0003

6 H E AV Y D U T Y L

U

N C

T

IO

N

S FUNCTIONS

• Rotating the inside lever, OR

• Turning the key in the outside lever-only when the inside push button is out,OR

• Removing the core with a control key and using a special emergency key

Pushing the inside button projects an “occupied” indicator in the outside lever and blocks all operating keys.

• Rotating the inside lever, OR

• Rotating the outside lever—only when the inside push button is out, OR

• Turning the key in the outside lever

Corridor

*ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal.

G

F91

Always unlocked• Pushing the inside button, OR

• Pushing and turning the inside button. Turning the button keeps the outside lever locked until the button is turned back

• Turning the key in the outside lever, (only when the button is not turned) OR

• Rotating the inside lever, (only when the button is not turned).

OR

• Closing the door (only when the button is not turned)

Cannot be locked

Pushing the inside button blocks all operating keys, but no “occupied” indicator is projected.

Turning the key in either the inside or the outside, locks or unlocks both sides.

Double Keyed* Functions

• Turning the key in the outside lever, OR

• Rotating the inside lever

• Rotating the inside lever, OR

• Rotating the outside lever-only when the inside push button is out. OR

• Turning the key in the outside lever

• Rotating the inside lever, OR

• Turning the key in the outside lever-only when the inside push button is out, OR

• Removing the core with a control key and using a special emergency key

• Rotating the inside lever,OR

• Turning the key in the outside lever, OR

• Rotating the outside lever when not locked by key

• Rotating the inside lever, OR

• Rotating the outside lever when not locked by key or push button

• Rotating the inside lever, OR

• Rotating the outside lever when not locked by key, OR

• Turning the key in the outside lever

• Rotating the outside lever when not locked by key, OR

• Rotating the inside lever when not locked by key

Always fixed

• Pushing the inside button, OR

• Pushing and turning the inside button. Turning the button keeps the outside lever locked until the button is turned back

Turning the key in the outside lever

• Turning the key in the outside lever, OR

• Pushing the button on the inside lever

Turning the key in the inside lever

• Turning the key in the inside lever, OR

• Turning the key in the outside lever

Cannot be unlocked

• Turning the key in the outside lever, OR

• Rotating the inside lever, OR

• Closing the door-only when the button is not turned, OR

• Turning back the slotted button

Key block feature is released by:

• Rotating the inside lever, OR

• Closing the door

• Turning the key in the outside lever, OR

• Rotating the inside lever (only when locked by push button),OR

• Closing the door (only when locked by push button)

Entrance

AB

F109

Storeroom

D

F86

Service Station

E

F92

Hotel Guest Rm.

H

F93

Hotel Guest Rm.

HJ

Classroom

R

F84

T

F90

Dormitory

C

F88

Storeroom *

Always unlockedCannot be locked

Always unlockedCannot be locked

Always fixed Always unlockedCannot be locked

• Turning the key in the inside lever, OR

• Turning the key in the outside lever

Always fixed Key block feature is released by:

• Rotating the inside lever, OR

• Closing the door

Always unlockedCannot be locked

Turning the key in the outside lever

Always unlockedCannot be locked

Always unlockedCannot be locked

Always unlockedCannot be lockedTurning the key in the inside lever

• Turning the key in the inside lever, OR

• Turning the key in the outside lever

• Turning the key in the inside lever, OR

• Turning the key in the outside lever

DescriptionFunction & Diag.

(ANSI No.) Locked by Unlocked by Locked by Unlocked by

Inside LeverOutside Lever Latch operated by

Single Keyed Functions

Attachment 5 FA4855-18-R-0003

L M HAMPTON

Line

L M HAMPTON

Line

L M HAMPTON

Line

O C K - L E V E R S 7

*ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal.

Single Dummy Trim

2DT

DescriptionFunction & Diag.

(ANSI No.) Locked by Unlocked by Locked by Unlocked by

Inside LeverOutside Lever Latch operated by

Communicating*

S

F80

Institutional*

W

F87

Keyless Functions Privacy

L

F76

Passage

N

F75

Exit

NX

F89

Patio

P

F77

Exit

Y

Double Dummy Trim

1DT

• Turning the key in the inside lever, OR

• Turning the key in the outside lever, OR

• Rotating the inside or outside lever (if unlocked)

Turning the key in either lever, locks or unlocks its own lever independently.

• Turning the key in the inside lever, OR

• Turning the key in the outside lever

• Rotating the inside lever

OR

• Rotating the outside lever only when the inside push button is out

• Rotating the inside lever, OR

• Rotating the outside lever

Rotating the inside lever

• Rotating the inside lever, OR

• Rotating the outside lever only when the inside push button is out

Rotating the inside lever

This is a single, surface-mounted lever for an inactive door or a non-latching door

This is a through bolt mounted pair of matching levers for an inactive door or a non-latching door

Turning the key in the outside lever

Always fixed

Pushing the inside button

Cannot be locked

Turning the key in the outside lever

Cannot be unlocked

Always fixed

• Rotating the outside slotted button, OR

• Rotating the inside lever, OR

• Closing the door.

Always unlocked

Always fixed

Pushing the inside button

Cannot be locked

Turning the key in the inside lever

Turning the key in the inside lever

Always fixed Cannot be unlocked

Cannot be locked Always unlocked

Always unlocked

Cannot be locked Always unlocked

• Rotating the inside lever, OR

• Closing the door

Cannot be locked Always unlocked

Cannot be locked Always unlocked

F U

N C

T

IO

N

SFUNCTIONS

IN

• Rotating inside lever, OR

• Rotating outside lever only when not locked by inside or outside key

Intruder • Turning key in the inside lever, OR

• Turning the key in the outside lever

• Turning key in the inside lever, OR

• Turning the key in the outside lever

Cannot be locked Always unlocked

Double Keyed Functions (Continued)

Attachment 5 FA4855-18-R-0003

INTEGRATED SOLUTIONS

GUEST HOUSING

IN

T E G

R A

T

D

O

L U

T

IO

N S

G

U E S T

H

O U

S

IN

G

2 I N T E G R A T E D

INTRODUCTION

Lever Styles KG Specifications KG Function EX Specifications Battery Life Chart How To Order

TABLE OF CONTENTS

Introduction Software and Hardware Features Standard Cards System Components HG Specifications HG Functions

PagePage

Card Specifications:

• Standard credit card size

• .030" ±.003 thickness

(PVC or Polyester)

• High coercivity ABA 3 tracks

S T D

C

A R

STANDARD CARDS

BEST serialized cards

VPA-PVC

Custom graphics cards

VPA-POLY

Photo I.D. Cards

VPA-CUST

Introducing B.A.S.I.S.®G – a highly efficient stand-alone lock system that utilizes card reader technology and is driven by software specifically designed for residence halls. B.A.S.I.S.® G, ID cards are encoded with all the information necessary to control door access. The system integrates with virtually any existing database, and allows unsurpassed capabilities in storing and retrieving access activity data. B.A.S.I.S.® G involves no costly wiring, is easy to manage, and offers a broad range of integrated features. In fact, everything about B.A.S.I.S.® G was designed to think . . .so you don’t have to. The world of access control has become increasingly complex. This is especially true at campus residence halls. As higher demands are being made for student safety, there is also a greater need for convenience and efficiency for facility managers. The real genius of B.A.S.I.S.® G is in its ability to address both challenges.

B.A.S.I.S.® G utilizes pre-programmed ID cards, the likelihood of unauthorized door access is greatly reduced. And because the lock itself is off-line, individual door access changes can be made quickly and conveniently. Add to this the ease with which B.A.S.I.S.® G integrates into existing systems, and the incredible amount of data that can be tracked and stored.

B.A.S.I.S.® G is doing the thinking so you don’t have to.

S O

F T W

A R

H

A R

D W

A R

E

F E A

T U

R E

S SOFTWARE FEATURES

• Designed specifically for the residence hall application, addressing the real life needs of daily operations such as lost cards and/or room changes.

• Term-based software allows for batch updating of data, saving significant and valuable time.

• Dynamically integrates with most existing university databases with real-time information updates, eliminating the tedious process of re-entering student data.

• Multiple locations can be networked to conveniently access a single database.

• Expiration date on cards prevents students from returning to their rooms after the semester has expired.

• Complete history of access activity can easily be obtained.

• Automatic backup reduces the risk of losing data.

• B.A.S.I.S.® G (an off-line system) is integrated into BEST’s on-line software, eliminating the inefficiencies of having two separate systems.

HARDWARE FEATURES

• Track Three technology greatly reduces the need to visit individual rooms for access changes. Locks do not have to be re-programmed to handle lost cards or room changes.

• Swipe reader is vandal resistant and can read various size I.D. cards.

• Minimum 65,000 cycles / 2 to 5 year battery life for cylindrical chassis; Minimum 130,000 cycles / 2 to 5 year battery life for mortise chassis.

• Costs are controlled by availability of replacement parts versus having to replace entire unit.

• Local factory-trained technical services are available 24 hours a day to meet any emergency need.

• B.A.S.I.S.® G can allow or record 5,000 users / history, giving unmatched capacity for each residence hall room.

• Available with a smart card reader, allowing for future technological advancements.

• Heavy-duty mechanical platform designed and manufactured for the toughest residence hall applications.

• Key override detection records and documents when a key is used.

• Deadbolt sensing prevents access to unauthorized cards when deadbolt is thrown.

• Interchangeable core mechanical override allows for emergency access.

• B.A.S.I.S.® G hardware is available in trims and most finishes that match BEST’s 9K cylindrical series and 30H mortise series, providing aesthetic continuity.

• Weather-resistant for versatile applications, including doors exposed to inclement conditions.

IN

T R

O D

U C

T

IO

N

Latch w/o key override

Deadbolt w/o key override

Deadbolt w/ key override

Latch w/key override

Internal motor drive mechanism operated by electronic signal, when presenting valid token. Green light indicates valid access. Red light and sounder indicate invalid access attempt. Lock records card number, time, date and type of event.

Diagram Function Mechanical Electronic Code

5 S O L U T I O N S

HG FUNCTIONS

U

N C

T

IO

N S

LEVER STYLES

L E V

Y

L E S

Latchbolt operated by lever either side, except when outside lever is locked by internal motor drive mechanism; latchbolt is retracted by key outside.

Deadbolt operated by key outside and turn lever inside. When deadbolt is extended, turning inside lever or electronically unlocked outside lever retracts both deadbolt and latchbolt simultaneously.

Auxiliary latch deadlocks latchbolt.

Internal motor drive mechanism operated by electronic signal when presenting valid card. Green light indicates valid access. Red light and sounder indicate invalid access attempt. Lock records card number, time, date and type of event. Electronic sensor recognizes whether deadbolt is retracted or thrown. Lock grants access only to deadbolt-authorized personnel when deadbolt is thrown.Latchbolt operated by lever either side, except when outside lever is locked by internal motor drive mechanism. Deadbolt operated by turn lever inside. When deadbolt is extended, turning inside lever or electronically unlocked outside lever retracts both deadbolt and latchbolt simultaneously.

Auxiliary latch deadlocks latchbolt.

TV

LV

Latchbolt operated by lever either side, except when outside lever is locked by internal motor drive mechanism. Auxiliary latch deadlocks the latchbolt.

NV

DV Latchbolt operated by lever either side,except when outside lever is locked by internal motor drive mechanism; latchbolt is retracted by key outside.

Auxiliary latch deadlocks the latchbolt.

“HG” lever style #14

“HG” lever style #16 “HG” lever style #17

“HG” lever style #3 “HG” lever style #12“HG” lever style #4

“KG” lever style #14

“HG” lever style #15

“KG” lever style #15 “KG” lever style #16

Attachment 5 FA4855-18-R-0003

DV

6 I N T E G R A T E D

K

N C

T

IO

N

KG FUNCTION

Diagram Function Mechanical Electronic Code

Internal motor drive mechanism operated by time-activated electronic signal or presenting valid card/ PIN. Green light indicates valid access. Red light and sounder indicate invalid access attempt. Lock records card number, time, date and type of event.

Dead locking latchbolt operated by lever either side, except when outside lever is locked by internal motor drive mechanism;

latchbolt is deadlocked

Cylindrical latch key override

MECHANICAL

Materials: Internal parts are brass, zinc or corrosion-treated steel.

Chassis: 2 1⁄16" diameter to fit 2 1⁄8" diameter hole in door.

Strike: Brass or bronze, 4 7⁄8" x 1 1⁄4" x 3⁄32". Fits standard door frame cut out as specified in ANSI A115.1. Correct strike automatically supplied with unit.

Backset: 2 3⁄4" standard, 3 3⁄4" and 5" available.

Door thickness: For doors 1 3⁄4" – 2 1⁄4" thick.

Installation: Lock dimensions requires modified door prep ANSI A156.2, Series 4000, Grade 1 to mount housing.

Core housing: 7 pin core.

Latchbolt: 9⁄16" throw.

Trim housing: 10 3⁄8" H x 3 1⁄4" W x 1" D sloping down to 3⁄4".

Lever handle: Made from high-quality zinc alloy. Body is approximately 1 5⁄8" in diameter: Handle is approximately 4 3⁄4" in length (from center-line of chassis). (Lever #3, #14 and #15 conform to California Titles 19 and 24.)

Finish: 605-bright brass, clear coated; 606-satin brass, clear coated; 612-satin bronze,clear coated; 625-bright chromium plated; 626-satin chromium plated; 690*- dark bronze coated (brass base material) *690 finish will continue as a dark brown appearance over time.

ELECTRONIC

Magnetic Stripe Card Reader:

Primary power: 4 AA Alkaline batteries.

User feedback indicators: Audible and Visible.

Operating temperature (Exterior side of door): -35°C to +66°C (-31°F to +150°F).

Read rate: 2 to 60 inches per second.

Card thickness: Accepts standard 0.030 inch card thickness.

Compliance: Compliant with FCC, Canadian, and European EMC requirements and for FCC Class A digital interference.

Dual Validation – Combination Keypad & Magstripe Reader:

Bezel size: 2 5⁄8" x 3 1⁄4" .

Material: Bezel– High impact ABS. Keypad– Encapsulated elastomer.

ESD Protection: 15KV.

Button operating life: 1 million cycles.

Operating temperature: -35°C to +66°C (-31°F to +151°F).

Compliance: Compliant with FCC, Canadian, and European EMC requirements and for FCC Class A digital interference.

P

E C

IF

IC

A T

IO

N

S KG SPECIFICATIONS

9KG Dual Validation Reader9KG Magnetic Stripe Reader

Attachment 5 FA4855-18-R-0003

LMH0114

Line

7 S O L U T I O N S

B.A.S.I.S. EX SERIES

B .A

.S .I .S

X

R

IE

S

B A

T T E R

Y

L

IF

E

C

H A

R T

Magstripe

Dual Val

65,000 / 2–5 yrs.

65,000 / 2–5 yrs.

130,000 / 3–5 yrs.

130,000 / 3–5 yrs.

130,000 / 3–5 yrs.

130,000 / 3–5 yrs.

250,000 / 4–5 yrs.

145,000 / 3–5 yrs.

Reader Cylinder Mortise Cylinder Mortise Cycles, Years Cycles, Years Cycles, Years Cycles, Years

BATTERY LIFE CHART

Standard Battery Pack Extended Battery Pack (Not available on EX Series)

MECHANICAL

Materials: Internal parts are brass, zinc or corrosion-treated steel. Brass or bronze, 4 7⁄8" x 1 1⁄4" x 3⁄32".

Fits standard door frame cut out as specified in ANSI A115.1. Correct strike automatically supplied with unit.

Lever handle: Brass or bronze. (Lever #14 and #15 conform to California Titles 19 and 24.)

Finish: 606-Satin brass, clear coated; 613-oxidized satin bronze, oil rubbed; 626-satin chromium plated; 690*- dark bronze coated (brass base material).

*613 finish is designed to wear over time, providing an “antique” appearance.

ELECTRONIC

Primary power: Alkaline battery pack.

Memory backup: Maintains programming to 100 years.

User feedback indicators: Visual and Audible.

Operating & Storage temperature: -30°C to +60°C (-22°F to +140°F).

Relative humidity: 10% to 90% non-condensing.

Shock: 2000 Gs RMS (maximum door-slam shock)

Compliance to FCC , Canadian, EMC requirements; for interference FCC Class A digital apparatus.

KEYPAD

Bezel size: 2 5⁄8" x 3 1⁄4" Material: Bezel–high impact ABS, Keypad–silicone rubber.

ESD Protection: 15KV.

Button operating life: 3-5 million cycles.

Button operating force: 3.88 ounces.

Operating temperature: -35°C to +55°C (-31ºF to +101ºF).

Storage temperature: -40°C to +55°C (-40ºF to +101ºF).

Sealing: Weatherproof gasket provides protection for outdoor use.

(Usable in all environmental/exterior applications.)

Magnetic Strip/Keypad Combination Card Reader

Magnetic Stripe Card Reader

Stanley Security Solutions, Inc.

6161 E. 75th Street Indianapolis, Indiana 46250 www.stanleysecuritysolutions.com

© 2006 Stanley Security Solutions, Inc. and Stanley Logistics

10M 1106FP

BAS025 Litho USA

45HG– 0**– DV– latch Levers: DV– dual validation 626 690 RH EXBB*– extended B.A.S.I.S. G keyless with key 3**– solid tube/ (magstripe and keypad) RHRB life battery pack

7– 7 pin TV– deadbolt w/return MS– magnetic stripe Satin* LH (Battery door housing; with key 12*– solid tube/ DVA– other cylinder 606 612 LHRB available in 622 accepts LV– deadbolt no return MSA– other cylinder finish only) all BEST without key 14– curved Bright* KOS*– key cores NV– latch return 605 625 override sensor without key 15– contour SH*– security angle return head screws

16– curved Thick door*– no return specify thickness

17*– gull wing TAC*– tactile lever 7/8" LTC*– flat lip strike

H O

W

D

E R

HOW TO ORDER-B.A.S.I.S. KG

93KG 7 DV 14 MS STK 626

Backset Core Function Lever Rose Strike Finish Options

Housing Code Style Style Package

HOW TO ORDER-B.A.S.I.S. HG

45HG 7 TV 14 MS 626 RH

Series Core Function Lever Trim Finish Door Options

Housing Code Style Style Hand

93KG– 2 3/4" 0– keyless DV– with 14– curved DV– dual val STK– 626 690 EXBB*– extended life battery pack 94KG– 3 3/4" 6– 6 pin key return (magstripe standard LM– lost motion 95KG– 5" non-IC cyl. 15– contour and keypad) S3– ANSI Satin* SH*– security head screws

7– 7 pin angle return MS– magnetic 606 612 TAC*– tactile lever housing; 16– curved stripe 3/4*– 3/4" throw latch accepts all no return Bright* 7/8" LTC* – flat lip strike BEST 605 625 OB**– non-IC zero-botted cores KA**– non-IC keyed alike

KD**– non-IC keyed different COR***– non-IC Corbin-Russwin MED***– non-IC Medeco SAR***– non-IC Sargent SCH***– non-IC Schlage YAL***– non-IC Yale SCHRC***– Schlage RC

EXG– 0** – EV– with 14– curved MS– magnetic 626 690 RHRB VD9– VonDuprin RM– rim*** SH*– B.A.S.I.S. G keyless key** return stripe satin* LHRB 98/99 series MO–mortise security

7– 7 pin NV– w/out 15– contour DV– dual val 606 613 PH1– Precision RD– surface head housing; key angle return (magstripe hardware 1000 & concealed screws accepts and keypad) PH2– Precision vertical rods Thick all BEST hardware 2000 Door*– cores SA8– Sargent specify

8000 series *** thickness

HOW TO ORDER-B.A.S.I.S. EXG

EXG 7 EV 14 MS 626 RHR PH1 RM

Series Core Function Lever Trim Finish Door Manufacturer Locking Options

Housing Code Style Style Hand Type

* Extra cost option. Must specify keymark and number of keys ** EV function (key override) is not availabe on PH1000 (all models) Von Duprin mortise type, or Sargent Rim type device.

***SA8 Only available with Rim Type device.

* Extra cost option. ** Cost deduction. Must specify keymark and number of keys.

Knobs:

4– round

* Extra cost option. Must specify keymark and number of keys.

** Six-pin cylinder in Schlage “C” keyway included with 0B, KA, KD options. Must specify “6” for core housing.

*** Cylinder not included with COR, MED, SAR, SCH, YAL, or SCHRC options. Must specify “0” for core housing.

Attachment 5 FA4855-18-R-0003

LMH0114

Line

LMH0114

Line

LMH0114

Line

LMH0114

Line

KEYPAD EZ LOCKS

E Y

P A

D E

Z L

O C

K

2 E L E C T R O N I C

HARDWARE FEATURES

• Heavy-duty mechanical platform designed and manufactured for the toughest applications.

• When the deadbolt is projected, deadbolt sensing prevents access by unauthorized PIN’s.

(Key override feature standard on Keypad EZ.)

• Mechanical override allows for emergency access.

• Available in common finishes and trims to match BEST’s 9K cylindrical series and 40H mortise series, providing aesthetic continuity.

• Available in cylindrical, mortise, and exit device trim platforms to meet most common applications.

• 12 position keypad design with audible and visual feedback.

• Standard battery pack yields a minimum of 65,000 cycles / 2-5 year battery life for cylindrical chassis, 130,000 cycles / 3 – 5 year battery life for mortise or exit trim platform.

• Optional extended battery pack yields twice the battery life as the standard battery pack.

• Local factory-trained technical services are available 24 hours a day to meet any emergency need.

• Replacement parts available.

• Features BEST’s standard 3 Year warranty.

• Weather-resistant for versatile applications, including doors exposed to inclement weather.

• Remote unlock standard.

SOFTWARE FEATURES

• Variable PIN length from 3 – 6 digits.

• Maximum of 50 users.

• All programming occurs through the keypad.

• Passage Mode privilege – authorized users can unlock device for extended periods of time.

• Deadbolt Override privilege – authorized users can gain access even when a mortise deadbolt is thrown.

• Provides for 1 Administrator PIN and 5 Supervisor PIN’s to allow easy management of groups of users.

T A

B L E O

F C

O N

T E N

T S

F E A

T U

R E S

HZ Trims KZ Specifications KZ Functions KZ Trims EXZ Specifications Order Procedure

TABLE OF CONTENTS

EZ Hardware Features EZ Software Features EZ Options Patented Keying EZ Accessories HZ Specifications HZ Functions

PagePage

EZ OPTIONS

AL– Besides complying with a wide variety of accessibility codes and ordinances, Best Access Systems lever handles are available with a special abrasive feature. Abrasive strip on the lever immediately identifies warnings on doors to hazardous areas for the blind.

EXBB– Extended life battery pack for double the operating life. (93KZ & 45HZ ONLY) LM– Lost motion feature allows the lever handle to move 45 degrees from parallel to the horizontal plane without engaging the latchbolt assembly. When the lockset is in the locked mode, this feature makes over-torque or over-leverage abuse more difficult to achieve. Note: Available in 9K cylindrical only.

Non-IC– The 9KZ may be adapted to existing keying systems by using a special retrofit lever and throw member that will accept 6-pin single shear-line cylinders from the following manufacturers: Corbin-Russwin, Medeco, Sargent, Schlage, Yale.

Note: Available in #15 lever style only. (Cylinder not supplied).

SH– Security head provided for all exposed screws.

Thick door–Specify thickness if other than 1 3⁄4".

TL– Tactile levers may be used in…