36C25518Q0169-00002031.pdf

ASBESTOS ASSESSMENT

ASBESTOS REINSPECTION REPORT

Jefferson Barracks Division 1 Jefferson Barracks Drive

St. Louis, Missouri

Building 3

Prepared for:

St. Louis V. A. Medical Center 1 Jefferson Barracks Drive

St. Louis, Missouri

Prepared by:

1421 Clarkview Road, Suite 100 P. O. Box 17867 Baltimore, MD 21209 Shreveport, Louisiana 71138-0867

(888) 776-0670 (318) 687-3771

INTRODUCTION

2008 ASBESTOS REINSPECTION REPORT

ST. LOUIS V. A. MEDICAL CENTER

JOHN COCHRAN AND JEFFERSON BARRACKS DIVISIONS

SCOPE OF WORK

1. The Inspector and Management Planner reviewed prior inspections and Management Plan information on file and compared this information with existing conditions for each facility.

2. This asbestos reinspection complies with the requirements of Asbestos Hazard Emergency Response Act (AHERA).

3. Each facility inspection was performed by an accredited inspector.

4. For each facility, the inspector performed the following tasks:

a. Visually reinspected and reassessed the condition of all friable known or assumed

ACBM.

b. Visually inspected material that was previously considered non-friable Asbestos- Containing Building Material (ACBM) and touched the material to determine whether it has become friable since the last inspection.

c. Identified any homogeneous areas with material that has become friable since the last inspection or reinspection.

d. The inspector collected bulk samples for analysis of newly friable material that is already assumed (not sampled) to be ACBM or collected additional bulk samples to fully assess the suspect materials.

e. Visually inspected, sampled, analyzed, and assessed the conditions of building materials that have been added to the facility since the last inspection or reinspection.

f. Assessed the condition of the newly friable material in areas where samples were collected and of newly friable material in areas assumed to be ACBM.

g. Reassessed the condition of friable known or assumed ACBM previously identified.

h. Recorded above information on field inspection forms for each facility.

5. A Management Planner reviewed the above information and performed the following required functions:

a. Reviewed each Management Plan for compliance with AHERA and verified that the plan reflects current conditions.

b. Reviewed the results of each reinspection and assessment.

c. Recommended in writing, the appropriate response actions.

d. Signed and dated the review documents, included the accreditation number of inspectors and planners, and submitted a copy to the Designated Person.

6. The following information was submitted to the Designated Person under AHERA, for inclusion in the Management Plan for each facility and, optionally, at a central office location.

a. The date of the inspection, the name and signature of the person making the inspection, state of accreditation, his or her accreditation number, and any changes in the condition of known or assumed ACBM.

b. If samples were collected, the exact locations where samples are collected during the inspection, a description of the manner used to choose sampling locations, the name and signature of each accredited inspector who collected the samples, state of accreditation, and his or her accreditation number.

c. Any assessments or reassessments made of friable material, the name and signature of the accredited inspector making the assessments, state of accreditation, and his or her accreditation number.

MANAGEMENT PLAN RECOMMENDATIONS

The following general notes are for all facilities inspected during the Asbestos Reinspection.

These notes reference any deficiencies found in prior inspections, reinspections, and the current Management Plan.

1. Removal Priorities were developed for each homogeneous area. The Removal Priorities are an indicator of priorities for future repair work or abatement work to be scheduled as financial budgets allow. Please see the 2008 Reinspection Condition and Removal Priority Table for further detail.

2. The current condition of material was listed for each homogeneous area. The condition, location, and potential for disturbance factors are used for the hazard ranking. Please see the 2008 Reinspection Condition and Removal Priority Table for the condition summaries.

3. Records for custodial, janitorial, and maintenance staff who have received two-hour awareness training should be filed in the Management Plan.

4. Any new custodial, janitorial, or maintenance staff that have the potential to come in contact with asbestos-containing materials (ACM) are required to attend a two-hour awareness training class. Records of training for new employees should be filed in the Management Plan.

5. The Designated Person is required to inform workers and building occupants at least once a year about the Management Plan. This includes information about inspections, response actions, and post-response action activities that are planned or in progress.

Provide a copy of the notification to each facility and include a copy in the Management Plan.

6. Maintenance areas (boiler rooms, janitor closets, etc.) are required to have warning labels where ACM are located. Install warning labels in these areas as needed. Some older labels may have come loose and are no longer visible. Post the labels in a prominent location.

7. Review the enclosed 2008 Reinspection Condition and Removal Priority Table for maintenance actions that may be required and to establish priorities and budgets for future repair and abatement work.

8. Periodic “Surveillance Inspections” are required every six (6) months. This inspection should indicate the condition of the material and provide recommendations for repair or potential removal. Consistency of inspections is desired and, therefore, should be performed by the same individual(s) for all facilities. An accredited inspector is not required, but is recommended. Records of Surveillance Inspections should be filed in both the administrative and facility Management Plans.

9. ”Reinspections” are required every three (3) years. Updated information should be added to the Management Plan.

10. The existing Management Plan (original) is updated by this Three-Year Reinspection.

All procedures and methods listed in the Plan are still in effect and should be followed unless specifically updated or omitted by this inspection. This includes maintenance procedures, repairs to damaged material, response actions, record keeping, surveillance inspections, and training.

11. An accredited “Supervisor” should be on staff or available on a contract basis per AHERA guidelines. Certification paperwork should be filed in the training section of the Management Plan.

12. ACBM should only be removed by licensed and accredited contractors in the State of Missouri. Response actions related to abatement activity should be filed in the Management Plan. Removal of limited amounts of asbestos is within the scope of the Management Plan by the accredited Supervisor and trained individuals.

13. Notification should be provided to “outside contractors” about ACM within the facility.

This should include such trades or services as telephone, electrical, plumbing, air conditioning, and other construction work. A form should be created for this purpose and placed in the Management Plan.

14. New building construction and portable buildings added to a facility are required to be inspected and sampled for ACM. In lieu of this, a letter from the architect, engineer, or manufacturer can be obtained that states “no ACM were specified or used in the facility”.

A copy of this letter is to be filed with the Management Plan at the facility. This letter will cancel the requirement for sampling.

15. Abatement Costs were developed for each homogeneous area and per facility. The estimated abatement cost is for budget purposes only. The cost is based on the area of material and estimated abatement costs for this material. The cost is for abatement only and does not include abatement design, air monitoring, or project observation costs.

REPORT SECTION

This report includes the following sections:

ACM Homogeneous Areas Summary Table and Drawings

This section provides a quick table reference to all asbestos-containing homogeneous areas found during the reinspection and drawings with the asbestos-containing homogeneous areas found during the 2008 asbestos reinspection.

Condition and Removal Priority Table

This section provides a table with the current condition, potential for disturbance, and removal priority for each homogeneous area.

Master Summary Table – Asbestos Bulk Samples

This table provides a listing of all asbestos bulk samples taken to date.

Asbestos-Containing Bulk Samples

This table provides a listing of all asbestos-containing bulk samples.

2008 Reinspection – Inspection Logs

This section provides the field inspection logs for samples taken during the 2008 asbestos reinspection.

Bulk Sample Location Drawings

This section provides drawings with sample locations for all asbestos bulk samples.

2008 Reinspection – Photographs

This section provides photographs of all asbestos bulk samples taken during the 2008 asbestos reinspection.

2008 Reinspection – Laboratory Reports

This section provides all laboratory analytical results.

Certifications

This section provides certifications for all Inspectors, the Management Planner who reviewed this Management Plan, and the laboratory that performed the bulk sample analysis.

Periodic Surveillance Forms

This section includes the forms completed during the periodic surveillance inspections required every six (6) months.

Management Plan Updates

This section includes the records of any asbestos abatement activities that are completed at the subject site. Notifications, daily notes, drawings, etc., should be placed in this section. This would also include air-monitoring data from asbestos abatement projects.

Response Actions

This section includes the records of any internal asbestos abatement or operation and maintenance activities that may be completed by V. A. employees. This would include any drawings, field notes, and air monitoring that was completed.

Training Documents

This section includes the records of training for the Designated Person and accredited Supervisor, as well as the two-hour awareness training for the custodial, janitorial, and maintenance staff.

Annual Notification Letters

This section includes copies of the annual Notification Letters provided to employees to inform them of the availability of the Management Plan.

Initial Inspection

This section contains the original asbestos inspection that was completed in 1994. This information was used to develop the 2008 Asbestos Reinspection.

CONTRACTORS

This 2008 Asbestos Reinspection was provided by:

Contractor: Subcontractor:

FINBACK 670, Inc. ALTEC Environmental Consultants, Inc.

1421 Clarkview Road, Suite 100 10100 Woolworth Road Baltimore, MD 21209 Keithville, LA 71047

(888) 776-0670 (Office) (318) 687-3771 (Office)

(877) 776-0670 (Fax) (318) 687-9923 (Fax)

INSPECTORS:

Brandon Odom Donald R. Joiner LA Certificate No. 9I01392 LA Certificate No. 8I01348 LA Certificate No. 9I01348

Eric Clipps Joshua Anders LA Certificate No. 9I01588 LA Certificate No. 9I01589

Justin L. Holcomb LA Certificate No. 9I00306

MANAGEMENT PLANNER:

Roy W. Dowling LA Certificate No. 9I00213 – Inspector LA Certificate No. 9P00072 – Management Planner

Accreditation Agency: Louisiana Department of Environmental Quality

ACM Homogeneous Areas Summary Table and Drawings

JEFFERSON BARRACKS DIVISION

2008 THREE-YEAR ASBESTOS REINSPECTION

ACM HOMOGENEOUS AREAS SUMMARY TABLE

Floor Flooring Materials Surfacing Materials TSI Materials Miscellaneous Materials

Basement HMA-01 12x12 Floor Tile & Adhesive No ACM HMA-04 Pipe Insulation & Fittings HMA-05 Fire Door (Assumed)

Floor Flooring Materials Surfacing Materials TSI Materials Miscellaneous Materials

HMA-01 12x12 Floor Tile & Adhesive HMA-02 9x9 Floor Tile & Adhesive

HMA-03 Floor Adhesive No ACM HMA-04 Pipe Insulation & Fittings HMA-05 Fire Door (Assumed)

Floor Flooring Materials Surfacing Materials TSI Materials Miscellaneous Materials

2 HMA-01 12x12 Floor Tile & Adhesive No ACM HMA-04 Pipe Insulation & Fittings HMA-05 Fire Door (Assumed)

Floor Flooring Materials Surfacing Materials TSI Materials Miscellaneous Materials

Attic No ACM No ACM HMA-04 Pipe Insulation & Fittings HMA-06 Transite Shingles

Building 3 - Basement

Building 3 - 1st Floor

Building 3 - 2nd Floor

Building 3 - Attic

BASEMENT

ST. LOUIS V.A. MEDICAL CENTER

2008 THREE-YEAR REINSPECTION

THERMAL SYSTEM INSULATION (TSI) SUMMARY TABLE

Room # Description Qty S/LF Ftgs TH/DI 001-03-JB magnesia pipe lagging 30 lf 0 4.00 001-03-JB magnesia pipe lagging 12 lf 0 6.00 001-03-JB magnesia pipe lagging 20 lf 0 8.00 001-03-JB magnesia pipe lagging 2 lf 0 12.00 001-03-JB mudded joint ftg on mag pipe lagging 0 ea 14 4.00 001-03-JB mudded joint ftg on mag pipe lagging 0 ea 8 6.00 001-03-JB mudded joint ftg on mag pipe lagging 0 ea 12 8.00 001-03-JB mudded joint ftg on mag pipe lagging 0 ea 2 12.00

002-03-JB magnesia pipe lagging 3 lf 0 4.00 002-03-JB magnesia pipe lagging 32 lf 0 6.00 002-03-JB mudded joint ftg on mag pipe lagging 0 ea 3 6.00 002-03-JB mudded joint ftg on wrapped pipe 0 ea 3 4.00

005-03-JB magnesia pipe lagging 10 lf 0 4.00 005-03-JB magnesia pipe lagging 10 lf 0 6.00 005-03-JB mudded joint ftg on mag pipe lagging 0 ea 1 4.00 005-03-JB mudded joint ftg on wrapped pipe 0 ea 3 4.00 005-03-JB wrapped paper pipe lagging 13 lf 0 4.00

006-03-JB magnesia pipe lagging 30 lf 0 4.00 006-03-JB magnesia pipe lagging 33 lf 0 6.00 006-03-JB mudded joint ftg on mag pipe lagging 0 ea 10 4.00 006-03-JB mudded joint ftg on mag pipe lagging 0 ea 8 6.00

008-03-JB magnesia pipe lagging 40 lf 0 4.00 008-03-JB mudded joint ftg on mag pipe lagging 0 ea 14 4.00

235 78

Building 3 - Basement

TOTALS

1st FLOOR

2ND FLOOR

ATTIC

ST. LOUIS V.A. MEDICAL CENTER

2008 THREE-YEAR REINSPECTION

THERMAL SYSTEM INSULATION (TSI) SUMMARY TABLE

Room # Description Qty S/LF Ftgs TH/DI 300-03-JB mudded joint ftg on wrapped pipe 0 ea 54 4.00 300-03-JB wrapped paper pipe lagging 265 lf 0 4.00

265 54

Building 3 - Attic

TOTALS

Condition and Removal Priority Table

Qualitative Ranking Numerical Rating

Good 8, 9, 10

Fair 4, 5, 6, 7

Poor 1, 2, 3

Physical Disturbance Environmental Disturbance

Low 1, 2, 3

Medium 4, 5, 6, 7

High 8, 9, 10

Qualitative Ranking Numerical Rating High 1, 2, 3

Medium 4, 5, 6, 7

Low 8, 9, 10

1 Qualitative Rankings and Quantitative (Numerical) Ratings for Current Condition

2 Qualitative Rankings and Quantitative (Numerical) Ratings for Potential for Disturbance

Assessment FactorsQualitative Ranking Numerical Rating

Description of Current Condition Surfacing material has no visible damage or small amounts of damage; covering on thermal system insulation is intact or has small amounts of damage; miscellaneous materials intact; no visible debris or small amounts of debris.

Address with on-going maintenance procedures

Maintain in good condition

Surfacing material has moderate but not extensive amounts of visible damage; covering on thermal system insulation is cut or torn, exposing moderate but not extensive amounts of insulation; moderate but not extensive damage to miscellaneous materials such as floor tile; moderate but not extensive amounts of visible dust and debris..

3 Qualitative Rankings and Quantitative (Numerical) Ratings for Removal Priority

Description of Current Condition Address short-term

Extensive damage to surfacing material; covering on thermal system insulation is cut or torn extensively and insulation itself is damage; miscellaneous materials such as floor tile extensively damaged and underlying mastic exposed; extensive amounts of dust and debris.

Accessibility: accessibility during normal operations

Activities: activities that people do and how often they do them

Vibration: vibration from operating machinery, HVAC equipment, and so forth

Air/Dust: air currents strong enough to dislodge loose ACM; airborne dust that can erode material

Corrosive: corrosive atmosphere or liquids that can erode the covering or matrix

Water Damage: water damage from leaking roof, pipe or other source

2008 THREE-YEAR ASBESTOS REINSPECTION

CONDITION AND REMOVAL PRIORITY TABLE

Rating Based On Rating Based On

HMA-01 3 Basement 12x12 Floor Tile & Adhesive No Yes 10 Intact 2 Floor Maintenance 7

HMA-04 3 Basement Pipe Insulation & Fittings Yes No 7 Damage 2 Access 6

HMA-05 3 Basement Fire Door (Assumed) No Restricted 10 Intact 1 Maintenance 10

HMA-01 3 1 12x12 Floor Tile & Adhesive No Yes 10 Intact 2 Floor Maintenance 7

HMA-02 3 1 9x9 Floor Tile & Adhesive No Yes 10 Intact 2 Floor Maintenance 7

HMA-03 3 1 Floor Adhesive No No 10 Intact 1 Access 9

HMA-04 3 1 Pipe Insulation & Fittings Yes No 7 Damage 2 Access 6

HMA-05 3 1 Fire Door (Assumed) No Restricted 10 Intact 1 Maintenance 10

Removal Priority 3

Building 3 - 1st Floor

Current Condition 1

Building 3 - Basement

Friable Yes/No

Accessibility Yes/No

Restricted

Potential for Disturbance 2

Homogeneous Area No. Bldg Floor Material Description

Master Summary Table Asbestos Bulk Samples

2008 THREE-YEAR ASBESTOS REINSPECTION

SUMMARY OF BULK SAMPLES TAKEN TO DATE

Building Floor Room Sample ID Material Description

JB3 00 001 JB-3-00-T-001-1 Magnesia pipe lagging JB3 00 002 JB-3-00-T-002-2 Off-white TSI JB3 00 005 JB-3-00-T-005-3 White TSI JB3 00 002 JB-3-00-T-002-4 Mudded joint fitting on magnesia pipe lagging JB3 00 002 JB-3-00-T-002-5 White TSI JB3 00 001 JB-3-00-T-001-6 Gray TSI JB3 00 005 JB-3-00-T-005-7 Wrapped paper pipe lagging JB3 00 008 JB-3-00-T-008-8 Gray TSI JB3 00 008 JB-3-00-T-008-9 Gray TSI JB3 00 005 JB-3-00-T-005-10 Mudded joint fitting on wrapped pipe JB3 00 008 JB-3-00-T-008-11 White TSI JB3 00 008 JB-3-00-T-008-12 White TSI JB3 00 018 JB-3-00-T-018-13 Mudded joint fitting on fiberglass JB3 00 005 JB-3-00-T-005-14 Gray TSI JB3 00 015 JB-3-00-T-015-15 Gray TSI JB3 00 H004 JB-3-00-M-H004-16 2x2 white w/worm & pinholes ceiling tile JB3 00 H004 JB-3-00-M-H004-17 4" charcoal cove base JB3 00 S003 JB-3-00-M-S003-18 4" black cove base JB3 00 S003 JB-3-00-M-S003-19 White/brown drywall JB3 00 008 JB-3-00-S-008-20 Beige smooth hardwall plaster JB3 00 018 JB-3-00-S-018-21 Gray textured hardwall plaster JB3 00 005 JB-3-00-M-005-22 White vinyl duct connector JB3 01 100 JB-3-01-M-100-1 2x2 white w/worm & pinholes ceiling tile JB3 01 H103 JB-3-01-M-H103-2 2x2 white w/gouges ceiling tile JB3 01 H101 JB-3-01-M-H101-3 2x2 white w/fissure pattern ceiling tile JB3 01 100 JB-3-01-M-100-4 4" black cove base JB3 01 H103 JB-3-01-M-H103-5 4" brown cove base JB3 01 101 JB-3-01-M-101-6 4" taupe cove base JB3 01 S102 JB-3-01-M-S102-7 4" ivory cove base JB3 01 S102 JB-3-01-M-S102-8 Tan stair tread JB3 01 122A JB-3-01-M-122A-9 Offwhite/brown gypsum drywall JB3 01 H103 JB-3-01-S-H103-10 Gray smooth hardwall plaster JB3 01 100 JB-3-01-S-100-11 Beige textured hardwall plaster JB3 01 100 JB-3-01-M-100-12 Black vinyl duct connector JB3 02 200 JB-3-02-M-200-1 2x2 white w/worm & pinholes ceiling tile JB3 02 H203 JB-3-02-M-H203-2 2x2 white w/gouges ceiling tile JB3 02 233 JB-3-02-M-233-3 4" black cove base JB3 02 206A JB-3-02-M-206A-4 4" brown cove base JB3 02 S202 JB-3-02-M-S202-5 4" ivory cove base JB3 02 S202 JB-3-02-M-S202-6 Tan stair tread JB3 02 200 JB-3-02-M-200-7 White/brown gypsum drywall JB3 02 H203 JB-3-02-S-H203-8 Off-white smooth hardwall plaster JB3 02 200 JB-3-02-S-200-9 Beige textured hardwall plaster JB3 02 208 JB-3-02-M-208-10 Dark green canvas duct connector JB3 03 300-Attic JB-3-03-T-300-1 Wrapped paper pipe lagging

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Purple = Abated ACM

1994 Initial Asbestos Inspection

2008 THREE-YEAR ASBESTOS REINSPECTION

SUMMARY OF BULK SAMPLES TAKEN TO DATE

Building Floor Room Sample ID Material Description

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Purple = Abated ACM

JB3 03 300-Attic JB-3-03-T-300-2 Brown/gray TSI JB3 03 300-Attic JB-3-03-T-300-3 Brown/gray TSI JB3 03 300-Attic JB-3-03-T-300-4 Mudded joint fitting on wrapped pipe JB3 03 300-Attic JB-3-03-T-300-5 White TSI JB3 03 300-Attic JB-3-03-T-300-6 White TSI JB3 03 300-Attic JB-3-03-T-300-7 Dark green canvas duct connector

JB3 00 019 JB-03-00-F-019-001A Light brown 12x12 floor tile, black mastic JB3 00 H004 JB-03-00-S-H004-002A Tan textured wall material JB3 00 H004 JB-03-00-S-H004-003A Tan textured ceiling material JB3 00 018 JB-03-00-T-018-004A 2" elbow - white wrap, white block insulation JB3 00 018 JB-03-00-T-018-005A 2" vertical - white wrap, yellow fiberglass insulation JB3 00 018 JB-03-00-M-018-006A Brown vibration JB3 00 006 JB-03-00-T-006-007A 6" elbow - white wrap, white block insulation JB3 00 006 JB-03-00-T-006-008A 6" vertical - brown wrap, brown insulation JB3 00 011 JB-03-00-T-011-009A 6" elbow - white wrap, white block insulation JB3 00 011 JB-03-00-T-011-010A 4" horizontal - white wrap, yellow fiberglass JB3 00 012 JB-03-00-F-012-011A Layer 1 - Gray 12x12 floor tile JB3 00 012 JB-03-00-F-012-011A Layer 2 - Yellow mastic JB3 00 008 JB-03-00-M-008-012A Black paneling material JB3 01 100 JB-03-01-F-100-013A Layer 1 - Green 9x9 floor tile JB3 01 100 JB-03-01-F-100-013A Layer 2 - Black mastic JB3 01 111 JB-03-01-F-111-014A Layer 1 - Brown 9x9 floor tile, black mastic JB3 01 111 JB-03-01-F-111-014A Layer 2 - Black mastic JB3 01 S102 JB-03-01-F-S102-015A Gray 12x12 floor tile, black mastic JB3 01 112 JB-03-01-F-112-016A Layer 1 - Brown 9x9 floor tile JB3 01 112 JB-03-01-F-112-016A Layer 2 - Black mastic JB3 01 101 JB-03-01-F-101-017A Layer 1 - Tan 12x12 floor tile JB3 01 101 JB-03-01-F-101-017A Layer 2 - Yellow mastic JB3 01 101 JB-03-01-F-101-017A Layer 3 - Brown 9x9 floor tile JB3 01 101 JB-03-01-F-101-017A Layer 4 - Black mastic JB3 01 109 JB-03-01-T-109-018A Black mastic, piping JB3 01 109 JB-03-01-M-109-019A Brown vibration isolator JB3 01 103 JB-03-01-T-103-020A White wrap, brown cardboard insulation JB3 01 107 JB-03-01-F-107-021A Layer 1 - Brown 9x9 floor tile JB3 01 107 JB-03-01-F-107-021A Layer 2 - Black mastic JB3 01 106 JB-03-01-F-106-022A Brown 9x9 floor tile, black mastic, felt JB3 01 105 JB-03-01-F-105-023A Layer 1 - Gray 12x12 floor tile JB3 01 105 JB-03-01-F-105-023A Layer 2 - Yellow mastic JB3 01 105 JB-03-01-F-105-023A Layer 3 - Brown 9x9 floor tile JB3 01 105 JB-03-01-F-105-023A Layer 4 - Black mastic JB3 01 105 JB-03-01-F-105-023A Layer 5 - Felt JB3 01 126 JB-03-01-F-126-024A Black mastic, brown 9x9 floor tile, black mastic, felt JB3 01 125 JB-03-01-F-125-025A Carpet adhesive, black mastic JB3 01 H102 JB-03-01-F-H102-026A Layer 1- Green 9x9 floor tile JB3 01 H102 JB-03-01-F-H102-026A Layer 2 - Black mastic

2008 Asbestos Reinspection

2008 THREE-YEAR ASBESTOS REINSPECTION

SUMMARY OF BULK SAMPLES TAKEN TO DATE

Building Floor Room Sample ID Material Description

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Purple = Abated ACM

JB3 01 100 JB-03-01-F-100-027A Layer 1 - Green 9x9 floor tile JB3 01 100 JB-03-01-F-100-027A Layer 2 - Black mastic JB3 02 S202 JB-03-02-F-S202-028A Gray 12x12 floor tile, black mastic JB3 01 Exterior JB-03-01-S-EXT-029A Tan textured material JB3 03 Roof JB-03-03-S-RF-030A Gray roofing shingle, felt

Asbestos-Containing Bulk Samples

2008 THREE-YEAR ASBESTOS REINSPECTION

LIST OF ASBESTOS-CONTAINING SAMPLES

Building Floor Room Sample ID Material Description

JB3 00 002 JB-3-00-T-002-2 Off-white TSI JB3 00 005 JB-3-00-T-005-3 White TSI JB3 00 002 JB-3-00-T-002-4 Mudded joint fitting on magnesia pipe lagging JB3 00 002 JB-3-00-T-002-5 White TSI JB3 00 005 JB-3-00-T-005-7 Wrapped paper pipe lagging JB3 00 008 JB-3-00-T-008-8 Gray TSI JB3 00 008 JB-3-00-T-008-9 Gray TSI JB3 00 005 JB-3-00-T-005-10 Mudded joint fitting on wrapped pipe JB3 00 008 JB-3-00-T-008-11 White TSI JB3 00 008 JB-3-00-T-008-12 White TSI JB3 03 300-Attic JB-3-03-T-300-1 Wrapped paper pipe lagging JB3 03 300-Attic JB-3-03-T-300-2 Brown/gray TSI JB3 03 300-Attic JB-3-03-T-300-3 Brown/gray TSI JB3 03 300-Attic JB-3-03-T-300-4 Mudded joint fitting on wrapped pipe JB3 03 300-Attic JB-3-03-T-300-5 White TSI JB3 03 300-Attic JB-3-03-T-300-6 White TSI

JB3 00 019 JB-03-00-F-019-001A Light brown 12x12 floor tile, black mastic JB3 00 006 JB-03-00-T-006-007A 6" elbow - white wrap, white block insulation JB3 00 012 JB-03-00-F-012-011A Layer 1 - Gray 12x12 floor tile JB3 01 100 JB-03-01-F-100-013A Layer 1 - Green 9x9 floor tile JB3 01 111 JB-03-01-F-111-014A Layer 1 - Brown 9x9 floor tile, black mastic JB3 01 S102 JB-03-01-F-S102-015A Gray 12x12 floor tile, black mastic JB3 01 112 JB-03-01-F-112-016A Layer 1 - Brown 9x9 floor tile JB3 01 101 JB-03-01-F-101-017A Layer 3 - Brown 9x9 floor tile JB3 01 107 JB-03-01-F-107-021A Layer 1 - Brown 9x9 floor tile JB3 01 105 JB-03-01-F-105-023A Layer 1 - Gray 12x12 floor tile JB3 01 H102 JB-03-01-F-H102-026A Layer 1- Green 9x9 floor tile JB3 01 100 JB-03-01-F-100-027A Layer 1 - Green 9x9 floor tile JB3 02 S202 JB-03-02-F-S202-028A Gray 12x12 floor tile, black mastic

1994 Initial Asbestos Inspection

2008 Asbestos Reinspection

2008 Reinspection Inspection Logs

Client: Date: October 8, 2008 Location: Inspector(s): Donald Joiner and Joshua Anders Address: 1 Jefferson Barracks Drive, St. Louis, Missouri

Note:

Sample ID Material Description Floor Room Location

JB-03-00-F-019-001A Light brown 12x12 floor tile, black mastic 00 019 Southeast corner of room 019

JB-03-00-S-H004-002A Tan textured wall material 00 H004 East wall by elevator

JB-03-00-S-H004-003A Tan textured ceiling material 00 H004 Above 2x2 ceiling tile on east wall

JB-03-00-T-018-004A 2" elbow - white wrap, white block insulation 00 018 Southeast quadrant on air handling unit

JB-03-00-T-018-005A 2" vertical - white wrap, yellow fiberglass insulation 00 018 Southeast quadrant on air handling unit

JB-03-00-M-018-006A Brown vibration 00 018 Southwest corner of room 018 on air handler unit

JB-03-00-T-006-007A 6" elbow - white wrap, white block insulation 00 006 Southwest corner of room 006

JB-03-00-T-006-008A 6" vertical - brown wrap, brown insulation 00 006 Southwest corner of room 006

JB-03-00-T-011-009A 6" elbow - white wrap, white block insulation 00 011 Northeast quadrant of room 011

JB-03-00-T-011-010A 4" horizontal - white wrap, yellow fiberglass 00 011 Northeast quadrant of room 011

JB-03-00-F-012-011A Layer 1 - Gray 12x12 floor tile 00 012 Southwest corner of room 012

JB-03-00-F-012-011A Layer 2 - Yellow mastic 00 012 Southwest corner of room 012

JB-03-00-M-008-012A Black paneling material 00 008 Southeast quadrant of room 008 bathroom stall wall

JB-03-01-F-100-013A Layer 1 - Green 9x9 floor tile 01 100 Northeast corner of room 100

ASBESTOS INSPECTION LOG

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Green = Non ACM (determined by Point Count analysis)

Jefferson Barracks Division - Building 3 St. Louis V. A. Medical Center

Address: 1 Jefferson Barracks Drive, St. Louis, Missouri

Note:

Sample ID Material Description Floor Room Location

ASBESTOS INSPECTION LOG

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Green = Non ACM (determined by Point Count analysis)

Jefferson Barracks Division - Building 3 St. Louis V. A. Medical Center

JB-03-01-F-100-013A Layer 2 - Black mastic 01 100 Northeast corner of room 100

JB-03-01-F-111-014A Layer 1 - Brown 9x9 floor tile, black mastic 01 111 Northeast corner of room 111 behind door

JB-03-01-F-111-014A Layer 2 - Black mastic 01 111 Northeast corner of room 111 behind door

JB-03-01-F-S102-015A Gray 12x12 floor tile, black mastic 01 S102 Northeast corner of room S102 behind door

JB-03-01-F-112-016A Layer 1 - Brown 9x9 floor tile 01 112 Northeast corner of room 112 behind door

JB-03-01-F-112-016A Layer 2 - Black mastic 01 112 Northeast corner of room 112 behind door

JB-03-01-F-101-017A Layer 1 - Tan 12x12 floor tile 01 101 Southwest quadrant of room 101 by door

JB-03-01-F-101-017A Layer 2 - Yellow mastic 01 101 Southwest quadrant of room 101 by door

JB-03-01-F-101-017A Layer 3 - Brown 9x9 floor tile 01 101 Southwest quadrant of room 101 by door

JB-03-01-F-101-017A Layer 4 - Black mastic 01 101 Southwest quadrant of room 101 by door

JB-03-01-T-109-018A Black mastic, piping 01 109 Above ceiling tile behind door

JB-03-01-M-109-019A Brown vibration isolator 01 109 Above ceiling tile behind door

JB-03-01-T-103-020A White wrap, brown cardboard insulation 01 103 Southwest corner of room 103 behind door in pipe chase

JB-03-01-F-107-021A Layer 1 - Brown 9x9 floor tile 01 107 In front of entrance to 107A

Address: 1 Jefferson Barracks Drive, St. Louis, Missouri

Note:

Sample ID Material Description Floor Room Location

ASBESTOS INSPECTION LOG

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Green = Non ACM (determined by Point Count analysis)

Jefferson Barracks Division - Building 3 St. Louis V. A. Medical Center

JB-03-01-F-107-021A Layer 2 - Black mastic 01 107 In front of entrance to 107A

JB-03-01-F-106-022A Brown 9x9 floor tile, black mastic, felt 01 106 Southwest corner of room 106

JB-03-01-F-105-023A Layer 1 - Gray 12x12 floor tile 01 105 Southeast corner of room 105

JB-03-01-F-105-023A Layer 2 - Yellow mastic 01 105 Southeast corner of room 105

JB-03-01-F-105-023A Layer 3 - Brown 9x9 floor tile 01 105 Southeast corner of room 105

JB-03-01-F-105-023A Layer 4 - Black mastic 01 105 Southeast corner of room 105

JB-03-01-F-105-023A Layer 5 - Felt 01 105 Southeast corner of room 105

JB-03-01-F-126-024A Black mastic, brown 9x9 floor tile, black mastic, felt 01 126 Southwest corner of room 126

JB-03-01-F-125-025A Carpet adhesive, black mastic 01 125 Southwest corner of room 125

JB-03-01-F-H102-026A Layer 1- Green 9x9 floor tile 01 H102 Northwest corner of room H102

JB-03-01-F-H102-026A Layer 2 - Black mastic 01 H102 Northwest corner of room H102

JB-03-01-F-100-027A Layer 1 - Green 9x9 floor tile 01 100 Southeast corner of room 100

JB-03-01-F-100-027A Layer 2 - Black mastic 01 100 Southeast corner of room 100

JB-03-02-F-S202-028A Gray 12x12 floor tile, black mastic 02 S202 Northeast corner of room S202

Address: 1 Jefferson Barracks Drive, St. Louis, Missouri

Note:

Sample ID Material Description Floor Room Location

ASBESTOS INSPECTION LOG

Red = Asbestos-Containing Material (ACM) Blue = Non ACM Green = Non ACM (determined by Point Count analysis)

Jefferson Barracks Division - Building 3 St. Louis V. A. Medical Center

JB-03-01-S-EXT-029A Tan textured material 01 Exterior Northeast quadrant of building

JB-03-03-S-RF-030A Gray roofing shingle, felt 03 Roof Southeast quadrant above entrance to building

GOOD = Surfacing material has no visible damage or small amounts of damage; covering on thermal system insulation is intact or has small amounts of damage; miscellaneous materials intact; no visible debris or small amounts of debris. FAIR = Surfacing material has moderate but not extensive amounts of visible damage; covering on thermal system insulation is cut or torn, exposing moderate but not extensive amounts of insulation; moderate but not extensive damage to miscellaneous materials such as floor tile; moderate but not extensive amounts of visible dust and debris. POOR = Extensive damage to surfacing material; covering on thermal system insulation is cut or torn extensively and insulation itself is damaged; miscellaneous materials such as floor tile extensively damaged and underlying mastic exposed; extensive amounts of dust and debris.

Material Category: F = Flooring S = Surfacing T = TSI M = Miscellaneous Friability: F=Friable NF=Non-Friable Condition: Good = 8, 9, 10 Fair = 4, 5, 6, 7 Poor = 1, 2, 3

Red = Asbestos-Containing Material Blue = Non Asbestos-Containing MaterialPlease use the following guidelines when reading this report:

Bulk Sample Location Drawings

BASEMENT

1st FLOOR

2ND FLOOR

ATTIC

2008 Reinspection Photographs

BUILDING 3

sample does not contain asbestos

JB-03-00-F-019-001A JB-03-00-S-H004-002A

JB-03-00-S-H004-003A JB-03-00-T-018-004A

sample contains asbestos

JB-03-00-T-018-005A JB-03-00-M-018-006A

JB-03-00-T-006-007A JB-03-00-T-006-008A

JB-03-00-T-011-009A JB-03-00-T-011-010A

JB-03-00-F-012-011A JB-03-00-M-008-012A

JB-03-01-F-100-013A JB-03-01-F-111-014A

JB-03-01-F-S102-015A JB-03-01-F-112-016A

JB-03-01-F-101-017A JB-03-01-T-109-018A

JB-03-01-M-109-019A JB-03-01-T-103-020A

JB-03-01-F-107-021A JB-03-01-F-106-022A

JB-03-01-F-105-023A JB-03-01-F-126-024A

JB-03-01-F-125-025A JB-03-01-F-H102-026

JB-03-01-F-100-027A JB-03-02-F-S202-028A

JB-03-00-S-EXT-029A

JB-03-00-S-RF-030A

2008 Reinspection Laboratory Reports

Sample Location Appearance % Type

AsbestosNon-Asbestos

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805097

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/09/08 4:15 PM

VAMC Reinspection VAMC Reinspection JB Building 03 Basement

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/10/2008Analysis Date:

Report Date: 10/10/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-00-F-019-

001A floortile 390805097-0001 lt brn 12x12 ft blk mastic

Brown Non-Fibrous

Heterogeneous

Chrysotile6%Non-fibrous (other)94%

JB-03-00-F-019-

001A adhesive 390805097-0001A lt brn 12x12 ft blk mastic

Black Non-Fibrous

Heterogeneous

Chrysotile12%Non-fibrous (other)86% Quartz2%

JB-03-00-S-H004-

002A 390805097-0002 tan textured wall material

Tan None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

JB-03-00-S-H004-

003A 390805097-0003 tan textured ceiling material

Tan None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

JB-03-00-T-018-

004A 390805097-0004

2" elbow wht wrap/wht block insulation

White None Detected

Non-Fibrous

Heterogeneous

Fibrous (other)3% Min. Wool37%

Non-fibrous (other)60%

JB-03-00-T-018-

005A 390805097-0005

2" vert pipe/wht wrap/ylw fiberglass insulation

Various None Detected

Fibrous

Heterogeneous

Cellulose4% Glass2% Min. Wool86%

Non-fibrous (other)8%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

Sue Ferrario (14) mailto:saintlouislab@emsl.com

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805097

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/09/08 4:15 PM

VAMC Reinspection VAMC Reinspection JB Building 03 Basement

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/10/2008Analysis Date:

Report Date: 10/10/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-00-M-018-

006A 390805097-0006 brown vibrator Brown None Detected

Fibrous

Heterogeneous

Fibrous (other)89% Non-fibrous (other)11%

JB-03-00-T-006-

007A 390805097-0007

6" elbow/wht wrap/wht block insulation

White Fibrous

Heterogeneous

Chrysotile38%Fibrous (other)6% Gypsum48% Non-fibrous (other)8%

JB-03-00-T-006-

008A 390805097-0008

6" vert pipe/brn wrap/brn insulation

Brown None Detected

Fibrous

Heterogeneous

Cellulose81% Fibrous (other)6% Synthetic4%

Non-fibrous (other)9%

JB-03-00-T-011-

009A 390805097-0009

6" elbow/wht wrap/wht block insulation

White None Detected

Non-Fibrous

Heterogeneous

Fibrous (other)3% Min. Wool37%

Non-fibrous (other)60%

JB-03-00-T-011-

010A 390805097-0010

4" hz pipe/wht wrap/ylw fiberglass insulation

Various None Detected

Fibrous

Heterogeneous

Cellulose4% Glass2% Min. Wool86%

Non-fibrous (other)8%

JB-03-00-F-012-

011A floortile 390805097-0011 gray 12x12 ft Gray Non-Fibrous

Heterogeneous

Chrysotile6%Non-fibrous (other)94%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805097

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/09/08 4:15 PM

VAMC Reinspection VAMC Reinspection JB Building 03 Basement

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/10/2008Analysis Date:

Report Date: 10/10/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-00-F-012-

011A adhesive 390805097-0011A gray 12x12 ft Yellow None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

JB-03-00-M-008-

012A 390805097-0012 black paneling material

Black None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

THIS IS THE LAST PAGE OF THE REPORT.

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805099

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/09/08 4:15 PM

VAMC Reinspection 08-14529 VAMC Reinspection JB Building 03 1st Floor

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/10/2008Analysis Date:

Report Date: 10/10/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-01-F-100-

013A floortile 390805099-0001 grn 9x9 ft blk mastic

Green Non-Fibrous

Heterogeneous

Chrysotile9%Non-fibrous (other)91%

JB-03-01-F-100-

013A adhesive 390805099-0001A grn 9x9 ft blk mastic

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose2% Non-fibrous (other)98%

JB-03-01-F-111-

014A floortile 390805099-0002 brn 9x9 ft blk mastic

Brown Non-Fibrous

Heterogeneous

Chrysotile9%Non-fibrous (other)91%

JB-03-01-F-111-

014A adhesive 390805099-0002A brn 9x9 ft blk mastic

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose9% Non-fibrous (other)91%

JB-03-01-F-S102-

015A floortile 390805099-0003 gray 12x12 ft blk mastic

Gray Non-Fibrous

Heterogeneous

Chrysotile7%Non-fibrous (other)93%

JB-03-01-F-S102-

015A adhesive 390805099-0003A gray 12x12 ft blk mastic

Black Non-Fibrous

Heterogeneous

Chrysotile12%Non-fibrous (other)88%

JB-03-01-F-112-

016A floortile 390805099-0004 brn 9x9 ft blk mastic

Brown Non-Fibrous

Heterogeneous

Chrysotile9%Non-fibrous (other)91%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

Sue Ferrario (8)

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805099

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/09/08 4:15 PM

VAMC Reinspection 08-14529 VAMC Reinspection JB Building 03 1st Floor

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/10/2008Analysis Date:

Report Date: 10/10/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-01-F-112-

016A adhesive 390805099-0004A brn 9x9 ft blk mastic

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose4% Non-fibrous (other)96%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

THIS IS THE LAST PAGE OF THE REPORT.

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

Sue Ferrario (8)

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805135

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/10/08 5:45 PM

VAMC Reinspection 08-14529 VAMC Reinspection JB Building 03 1st Floor

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/13/2008Analysis Date:

Report Date: 10/13/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-01-F-101-

017A flooring 390805135-0001 tan 12x12/ylw mastic/wood/brn 9x9/blk mastic

Tan None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

JB-03-01-F-101-

017A adhesive 390805135-0001A tan 12x12/ylw mastic/wood/brn 9x9/blk mastic

Yellow None Detected

Non-Fibrous

Heterogeneous

Cellulose2% Non-fibrous (other)96% Quartz2%

JB-03-01-F-101-

017A floortile 390805135-0001B tan 12x12/ylw mastic/wood/brn 9x9/blk mastic

Brown Non-Fibrous

Heterogeneous

Chrysotile12%Non-fibrous (other)88%

JB-03-01-F-101-

017A adhesive 390805135-0001C tan 12x12/ylw mastic/wood/brn 9x9/blk mastic

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose2% Non-fibrous (other)98%

JB-03-01-T-109-

018A 390805135-0002 blk mastic on piping

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose9% Non-fibrous (other)91%

JB-03-01-M-109-

019A 390805135-0003 brn vibration isolator

Brown None Detected

Fibrous

Heterogeneous

Fibrous (other)89% Non-fibrous (other)11%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

Sue Ferrario (25)

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805135

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/10/08 5:45 PM

VAMC Reinspection 08-14529 VAMC Reinspection JB Building 03 1st Floor

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/13/2008Analysis Date:

Report Date: 10/13/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-01-T-103-

020A 390805135-0004 wht wrap/brn cardboard insulation

Various None Detected

Fibrous

Heterogeneous

Cellulose88% Fibrous (other)4% Hair6%

Non-fibrous (other)2%

JB-03-01-F-107-

021A floortile 390805135-0005 brn 9x9 w/blk mastic

Brown Non-Fibrous

Heterogeneous

Chrysotile9%Non-fibrous (other)91%

JB-03-01-F-107-

021A adhesive 390805135-0005A brn 9x9 w/blk mastic

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose2% Non-fibrous (other)98%

JB-03-01-F-106-

022A flooring 390805135-0006 brn 9x9 w/blk mastic/felt/wood

Brown None Detected

Non-Fibrous

Heterogeneous

Cellulose17% Non-fibrous (other)83%

JB-03-01-F-106-

022A adhesive 390805135-0006A brn 9x9 w/blk mastic/felt/wood

Black None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

JB-03-01-F-106-

022A felt 390805135-0006B brn 9x9 w/blk mastic/felt/wood

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose49% Non-fibrous (other)51%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government.

Analysis performed by EMSL St. Louis (AIHA #102636, NVLAP # 200742-0, CA ELAP #2668)

% Fibrous % Non-Fibrous

Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized Light Microscopy

390805135

Attn: Roy W. Dowling ALTEC Environmental Consultants, Inc.

2920 Truly Lane Shreveport, LA 71138

Customer PO:

Received: 10/10/08 5:45 PM

VAMC Reinspection 08-14529 VAMC Reinspection JB Building 03 1st Floor

Customer ID: ALT50

Fax: (318) 687-9923 Phone: (318) 687-3771 Project:

EMSL Order:

EMSL Proj:

10/13/2008Analysis Date:

Report Date: 10/13/2008

EMSL Analytical, Inc.

11040A Lin-Valle Drive, Saint Louis, MO 63123 Phone: (314) 845-8910 Fax: (314) 845-6459 Email: saintlouislab@emsl.com

JB-03-01-F-105-

023A floortile 390805135-0007 grey 12x12/ylw mastic/wood/brn 9x9/bm/felt/wood

Gray Non-Fibrous

Heterogeneous

Chrysotile9%Non-fibrous (other)91%

JB-03-01-F-105-

023A adhesive 390805135-0007A grey 12x12/ylw mastic/wood/brn 9x9/bm/felt/wood

Yellow None Detected

Non-Fibrous

Heterogeneous

Cellulose2% Non-fibrous (other)98%

JB-03-01-F-105-

023A flooring 390805135-0007B grey 12x12/ylw mastic/wood/brn 9x9/bm/felt/wood

Brown None Detected

Non-Fibrous

Heterogeneous

Cellulose17% Non-fibrous (other)83%

JB-03-01-F-105-

023A adhesive 390805135-0007C grey 12x12/ylw mastic/wood/brn 9x9/bm/felt/wood

Black None Detected

Non-Fibrous

Heterogeneous

Non-fibrous (other)100%

JB-03-01-F-105-

023A felt 390805135-0007D grey 12x12/ylw mastic/wood/brn 9x9/bm/felt/wood

Black None Detected

Non-Fibrous

Heterogeneous

Cellulose47% Synthetic2%

Non-fibrous (other)51%

JB-03-01-F-126-

024A flooring 390805135-0008 blk mastic/wood/brn 9x9/blk mastic/felt/wood

Brown None Detected

Non-Fibrous

Heterogeneous

Cellulose17% Non-fibrous (other)83%

Jeff Siria, Laboratory Manager or other approved signatory

PLM-1

Analyst(s)

Due to magnification limitations inherent in PLM, asbestos fibers in dimensions below the resolution capability of PLM may not be detected. The limit of detection as stated in the method is 1%. The above test report relates only to the items tested and may not be reproduced in any form without the express written approval of EMSL Analytical, Inc. EMSL’s liability is limited to the cost of analysis. EMSL bears no responsibility for sample collection activities or analytical method limitations.