Attachment M Part 5 Prescriptive Specifications.pdf

P-325, SOF NSWG-2 SOF Human Performance Center 1602585 JEB Little Creek-Fort Story, Virginia Beach, Virginia

PART FIVE - PRESCRIPTIVE SPECIFICATIONS

HYDROTHERAPY EQUIPMENT

Hydrotherapy Pool

Provide a pre-packaged hydrotherapy pool, components and equipment by a single manufacturer. Pool must be made of structural aluminum wall panels, with integrated underwater treadmills and multiple resistance jets. The pool must be capable of maintaining 85°F water temperature (plus or minus 2 degrees).

Hydrotherapy pool will be installed flush with the facility’s hydro room floor. The tank walls, support structure, and pool components are located below the poolroom floor surface in the lower level pool equipment pit. Installation of pool and all associated components and equipment to be installed in compliance with manufactures installation instructions.

Provide one (1) shop pre-fabricated, aquatic therapy pool system. The unit will be 15’-

0” long by 11’-0” wide treatment area, varying water depths from 3’-6” to 7’-0”, with one (1) integrated / flush mounted into the pool floor system powered variable speed direct electric drive underwater treadmill specifically driven without hydraulics, two (2) front Badu resistance jet systems with adjustable flow nozzles allowing for directional and flow rate adjustments as well as an attachable massage hose (number of front jet systems to be selected by Contracting Officer), commercial filtration system, heater with variable controlled water temperature, removable stainless steel support bars, stairway handrail, cameras for underwater viewing, camera switching device, monitor, digital video recorder, additional side resistance jets (number of side jets to be selected by Contracting Officer) additional attachable massage hose and accessories to be selected by Contracting Officer.

Manufacturers: Subject to compliance with requirements, provide products by one of the following available manufacturers offering products that may be incorporated into the work includes, but are not limited to, the following:

a. HydroWorx

b. Hudson

c. SwimEx

Polar Plunge Pool

Provide a pre-packaged Polar Plunge Pool, components, and equipment by a single manufacturer. The pool must be one-piece acrylic design with a rigid fiberglass reinforced shell, bench seating, and spa jets. The pool must be capable of maintaining 50°F water temperature (plus or minus 2 degrees). The pool will be installed flush with the facility’s hydro room floor. The mechanical and electrical pool components are to be located below the floor surface in the lower level pool equipment pit.

Provide one (1) shop pre-fabricated aquatic therapy Polar (cold) Plunge Pool system. The unit includes controls, commercial filtration system, pre-plumbed spa jets, water-cooled chiller with variable controlled water temperature, digital temperature controller, tile border, additional resistance jet, additional attachable massage hose, stairway handrail, pool cover, and accessories to be selected by Contracting Officer.

PART FIVE - PRESCRIPTIVE SPECIFICATIONS - Page 1

Thermal Plunge Pool

Provide a pre-packaged Thermal Plunge Pool, components and equipment by a single manufacturer. The pool must be one-piece acrylic design with a rigid fiberglass reinforced shell, bench seating and spa jets. The pool must be equipped with thermal heating units to distribute warm or hot water to temperatures ranging from 94°F to 104°F. The thermal plunge pool will be installed flush with the facility’s hydro room floor. The mechanical and electrical pool components are to be located below the floor surface in the lower level pool equipment pit.

Provide one (1) shop pre-fabricated aquatic therapy Thermal (hot) Plunge pool system.

The unit includes controls, commercial filtration system, pre-plumbed spa jets, heater with variable controlled water temperature, digital temperature controller, tile border, additional resistance jets, additional attachable massage hose, stairway handrail, and pool cover, and accessories to be selected by Contracting Officer.

CLIMBING WALL EQUIPMENT

Provide a 34’-0” wide by 28’-0’ high climbing wall, coordinate the design requirements with the

Contracting Officer. Primary support requirements per manufacturer requirements. Provide four (4) climbing lines, hand holds, tie off points, autobelays, bolted anchors, etc. Coordinate general angles and types of terrain, fall zone, ingress/egress paths, and site lines with the Contracting Officer.

Manufacturers: Subject to compliance with requirements, provide products by one of the following available manufacturers offering products that may be incorporated into the work includes, but are not limited to, the following:

a. EP Climbing

b. Impact Climbing

c. Adventure Solutions