1614700dwg20of22MECHANICAL.pdf

M-101

MITERED ELBOW WITH TURNING VANES

VOLUME DAMPER

DUCT TRANSITION

DUCT TURNING UP

DUCT TURNING DOWN

EXHAUST DUCT SECTION

SUPPLY AIR DUCT SECTION

S

GRILLE, REGISTER, OR DIFFUSER DESIGNATION

FLOW (CFM)

DIFFUSER WITH FLEXIBLE CONNECTION

RETURN/TRANSFER GRILLE DESIGNATION

RADIUS ELBOW

ROUND DUCT SIZE (IN.)

RECTANGULAR DUCT SIZE (IN. x IN.)

10"∅

10"x10"

RETURN DUCT SECTION

DEMOLITION KEYNOTE DESIGNATION

EXHAUST GRILLE DESIGNATION

DUCT BRANCH CONNECTION

OUTDOOR UNIT DESIGNATION**-OU-1

AIR HANDLING UNIT DESIGNATION**-AHU-1

SECTION/CALLOUT VIEW

SECTION/CALLOUT SHEET

MEDIUM DETAIL LEVEL

HIGH DETAIL LEVEL

MEDIUM DETAIL LEVEL

HIGH DETAIL LEVEL

GENERAL NOTES LEGEND AND ABBREVIATIONS

1000 BRITISH THERMAL UNITS PER HOURMBH

MIN CIRCUIT AMPACITYMCA

HP HORSE POWER

' FEET

AFF

DB

EA

CFM

EAT

ESP

RETURN AIR

MAXIMUM

MINIMUM

LAT

RA

OA

MAX

MIN

SUPPLY AIR

WG

WB

RPM

SA

ENTERING AIR TEMPERATURE

CUBIC FEET PER MINUTE

ABOVE FINISHED FLOOR

REVOLUTIONS PER MINUTE

WET BULB TEMPERATURE

DRY BULB TEMPERATURE

EXTERNAL STATIC PRESSURE

LEAVING AIR TEMPERATURE

WATER GAUGE

OUTSIDE AIR

EXHAUST AIR

THROUGHTHRU

RS/RL REFRIGERANT SUCTION/LIQUID PIPING

°F DEGREES FAHRENHEIT

SENSIBLESENS

TYPICALTYP

ADJ ADJUSTABLE

DDC DIRECT DIGITAL CONTROLS

SEASONAL ENERGY EFFICIENCY RATIOSEER

VARIABLE FREQUENCY DRIVEVFD

PIPE TURNING UP

PIPE TURNING DOWN

DIRECTION OF SLOPE

CONDENSATE DRAIN PIPING

CONTINUATION

DIRECTION OF FLOW

BUTTERFLY VALVE

REDUCER

REFRIGERANT SUCTION/LIQUID PIPING

D

RS/RL

DIAGRAMS

MODEL VIEWS

M MOTORIZED DAMPER (MAX LEAKAGE OF 3 CFM/SF AT 1" WG)

PRESSURE DROP

FEET PER MINUTE

PACKAGE TERMINAL HEAT PUMP DESIGNATION

PD

FPM

MAX OVERCURRENT PROTECTIONMOCP

ANTI-TERRORISM FORCE PROTECTIONATFP

BRITISH THERMAL UNITS PER HOURBTUH

KILOWATTKW

FEETFT

NUMBER#/NO

DIGITAL THERMOSTAT

**-PTHP-1

CARBON DIOXIDE SENSORCO2

EXHAUST FAN DESIGNATION**-EF-1

INCHIN

1. GENERAL NOTES ON THIS DRAWING ARE APPLICABLE TO EACH

MECHANICAL DRAWING OF THIS SET. SEE EACH DRAWING FOR SPECIFIC

NOTES APPLICABLE TO THAT DRAWING.

2. OUTSIDE AIR INTAKE OPENINGS FOR VENTILATION AIR MUST BE LOCATED

AT LEAST 10 FEET MEASURED IN ANY DIRECTION FROM ANY FLUES,

VENTS, GAS METERS, GAS REGULATORS, OR PLUMBING VENTS UNLESS

TOP OF SUCH INTAKE OPENING IS 3 FEET BELOW ANY OF THE LISTED

ITEMS.

3. OVERHEAD PIPING IN SPACES WITHOUT CEILINGS MUST BE RUN AS

CLOSE TO STRUCTURE AS PRACTICAL, AS CLOSE TO PARALLEL JOISTS AS

POSSIBLE AND ABOVE LIGHTING FIXTURES.

4. OVERHEAD DUCTWORK AND PIPING IN SPACES WITH CEILINGS MUST BE

CONCEALED UNLESS OTHERWISE NOTED.

5. COORDINATE LOCATION OF GRILLES, REGISTERS, DIFFUSERS,

THERMOSTATS AND OTHER WALL OR CEILING MOUNTED HVAC

ACCESSORIES WITH REFLECTED CEILING PLAN, LIGHTING FIXTURE

LAYOUT AND ACCESSORIES PROVIDED BY OTHER TRADES SO AS TO

PRESENT A NEAT AND ATTRACTIVE INSTALLATION CONSISTENT

THROUGHOUT THE ENTIRE BUILDING. IT IS THE INTENT FOR GRILLES,

REGISTERS, AND DIFFUSERS TO BE PROVIDED IN THE CENTER OF CEILING

PANELS.

6. ARRANGE PIPING AND DUCTWORK, PARTICULARLY ABOVE CEILING, AS

REQUIRED TO CLEAR STRUCTURE, DUCTS, CONDUITS, ETC., ALLOWING

SPACE FOR PIPE HANGERS, EXPANSION LOOPS, AND ACCESS TO VALVES,

FILTERS, AND MAINTENANCE OF EQUIPMENT.

7. EQUIPMENT WITH FILTERS MUST BE PROVIDED SO THAT FILTERS CAN BE

EASILY REMOVED AND REPLACED.

8. VERIFY REFRIGERANT PIPE SIZES WITH EQUIPMENT MANUFACTURER FOR

THE INDICATED INSTALLATION.

9. COORDINATE LOCATION AND INSTALLATION OF EQUIPMENT WITH OTHER

TRADES.

10. THERMOSTATS MUST BE LOCATED IN THE ROOMS INDICATED, PROVIDED

48" ABOVE FINISH FLOOR.

11. EXTEND CONDENSATE PIPING AS INDICATED. ROUTING MUST NOT

INTERFERE WITH PASSAGEWAYS AND MAINTENANCE. DRAINS MUST BE

TRAPPED AND SLOPED AWAY FROM EQUIPMENT AT 1/8" PER FOOT.

12. PIPING AND DUCTWORK INSULATION MUST BE RUN CONTINUOUSLY

THROUGH NON-RATED FLOORS, WALLS, ROOF AND PARTITIONS, UNLESS

OTHERWISE INDICATED.

13. PIPING MUST BE SUPPORTED IN ACCORDANCE WITH LOCAL CODE

REQUIREMENTS. ADDITIONAL SUPPORTS OR HANGERS MUST BE LOCATED

ADJACENT TO ELBOWS TO PREVENT WEIGHT OF PIPING BEING PLACED

ON THE EQUIPMENT.

14. LOCATE AND SIZE HOUSEKEEPING PADS FOR MECHANICAL EQUIPMENT IN

ACCORDANCE WITH ACTUAL EQUIPMENT PURCHASED.

15. PROVIDE ACCESS DOORS IN DUCTWORK, WHERE REQUIRED, FOR

ACCESS TO SYSTEM COMPONENTS INCLUDING, BUT NOT LIMITED TO:

DAMPER MOTORS AND/OR MOTOR OPERATED DAMPERS.

16. DIMENSIONS FOR DUCTWORK SHOWN ON PLANS ARE INSIDE DUCT

DIMENSIONS. SEE SPECIFICATIONS FOR INSULATION THICKNESS

REQUIREMENTS. THE FIRST FIGURE OF DUCT SIZE INDICATES DIMENSION

OF FACE SHOWN OR INDICATED.

17. REFRIGERANT SUCTION AND LIQUID LINES MUST HAVE SEPARATE

INSULATION.

18. PROVIDE ALL MITERED ELBOWS IN SUPPLY DUCTWORK WITH TURNING

VANES.

19. VALVES, TRAPS, DAMPERS, CLEANOUTS, CONTROLS, ETC. MUST BE

PROVIDED SUCH THAT MANUFACTURER'S RECOMMENDED MAINTENANCE

CLEARANCE AND ADJUSTMENT ACCESS IS PROVIDED.

20. PROVIDE EQUIPMENT IN ACCORDANCE WITH MANUFACTURER'S

RECOMMENDATIONS.

21. PROVIDE EQUIPMENT WITH SIMILAR DIMENSIONS AS INDICATED ON

DRAWINGS.

22. CONTRACTOR MUST COORDINATE SEQUENCING OF INSTALLATION

BETWEEN MECHANICAL, PLUMBING, ELECTRICAL, AND FIRE PROTECTION

SYSTEMS PRIOR TO THE START OF CONSTRUCTION. COORDINATION

MUST ENSURE CEILING HEIGHTS OF THE ARCHITECTURAL DRAWINGS ARE

MAINTAINED. EQUIPMENT FOR EACH DISCIPLINE MUST BE COORDINATED

BETWEEN TRADES AND MOUNTED AS HIGH AS POSSIBLE IN THE CEILING

SPACE.

23. ARCHITECT MUST APPROVE ALL COLORS PRIOR TO ORDERING.

24. ALL PENETRATIONS THROUGH FIRE WALLS MUST MAINTAIN FIRE

INTEGRITY OF ASSEMBLY. COORDINATE FIRE WALLS WITH

ARCHITECTURAL/LIFE SAFETY PLANS.

25. PROVIDE COMPLETE AND FUNCTIONAL SYSTEM PROVIDED PER

MANUFACTURER'S RECOMMENDATIONS AND IN ACCORDANCE WITH

LOCAL CODES.

26. PROJECT MUST BE PHASED; SEE PROJECT PHASING PLAN AND

COORDINATE WITH GENERAL CONTRACTOR TO ENSURE SYSTEMS ARE

PHASED TO KEEP OTHER AREAS OPERATIONAL WITH EXISTING SYSTEM,

NEW SYSTEM OR TEMPORARY SYSTEM.

27. ALL COOLING COIL OR FUEL-FIRED EQUIPMENT WHICH PRODUCES

CONDENSATE MUST BE PROVIDED WITH A SECONDARY CONDENSATE

OVERFLOW SWITCH MOUNTED IN THE UNIT'S OVERFLOW DRAIN

CONNECTION TO DE-ENERGIZE THE UNIT UPON SENSING MOISTURE.

FLEXIBLE DUCT

T

EMERGENCY HVAC SHUTOFF SWITCHSW

ENLARGED REFERENCE PLAN

ENLARGED REFERENCE PLAN

INDOOR UNIT DESIGNATION**-IU-1

SQUARE FOOTSQ FT

MECHANICALMECH

ELEC ELECTRICAL

FLEXIBLEFLEX

CLEARANCE FOR MAINTENANCE OF EQUIPMENT

FIRE RATED WALL BOUNDARY

FIRE DAMPER

1 SHEET KEYNOTE DESIGNATION

LOUVER DESIGNATION**-LV-1

LIMIT OF DEMOLITION INDICATOR

NEW TO EXISTING CONNECTION

DEMOLITION INDICATOR

NOISE CRITERIANC

CONTROLLERC

VISITOR CENTER EQUIPMENT DESIGNATIONVC-**-*

INSPECTION STATION EQUIPMENT DESIGNATIONIS-**-*

ATFP SHUTOFF SWITCH DESIGNATIONSO

ATPF

MINI SPLIT OUTDOOR UNIT DESIGNATION**-MS-1

GRAVITY VENTILATOR DESIGNATION**-GV-1 ELECTRIC UNIT HEATER DESIGNATION**-EUH-1

ELECTRIC RADIANT FLOOR HEATER UNIT DESIGNATION**-ERH-1

LIQUID PROPANE UNIT HEATER DESIGNATION**-UH-1

" INCHES

° DEGREES

∅ PHASE/DIAMETER

HEIGHTH

WIDTHW

LP LIQUID PROPANE

SQUARE FEETSF

SUPPLY FAN UNIT DESIGNATION**-SF-1

VOC/H VOLATILE ORGANIC COMPOUND SENSOR AND HUMIDISTAT

VOLUME DAMPER DESIGNATION

FLOW (CFM)

GRAVITY VENTILATOR DESIGNATION**-GV-1

AFUE ANNUAL FUEL UTILIZATION EFFICIENCY

EDB ENTERING DRY BULB

EWB ENTERING WET BULB

LDB LEAVING DRY BULB

LWB LEAVING WET BULB

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:5

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-001

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

M E

C H

A N

IC

A

L

LE

G E

N D

, N O

TE

S

A

B B

R E

V

IA

T

IO

N S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -0

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

293 358

12881075

CODES AND STANDARDS (INCLUDING BUT NOT LIMITED TO)

IBC

IMC

IECC

ASHRAE 62.1

ASHRAE 90.1

UFC 3-410-01

UFC 4-010-01

INTERNATIONAL BUILDING CODE - 2015

INTERNATIONAL MECHANICAL CODE - 2015

DoD MINIMUM ANTITERRORISM STANDARDS FOR BUILDINGS - 12-12-2018

HEATING, VENTILATING, AND AIR CONDITIONING SYSTEMS - 11-01-2017

ENERGY STANDARD FOR BUILDINGS EXCEPT LOW-RISE RESIDENTIAL BUILDINGS -2019

VENTILATION FOR ACCEPTABLE INDOOR AIR QUALITY - 2019

INTERNATIONAL ENERGY CONSERVATION CODE - 2018

UFC 1-200-02 HIGH PERF & SUSTAINABLE BLDG. REQUIREMENTS - 12-01-2016

IFGC INTERNATIONAL FUEL GAS CODE - 2015

DESIGN CONDITIONS

SPACE

OFFICE/ADMIN

MECHANICAL/ELECTRICAL ROOMS

IT/COMM

INDOOR CONDITIONS OUTDOOR CONDITIONS

SUMMER WINTER

°F DB % RH °F DB

N/A

SUMMER WINTER

°F DB °F WB °F DB

82.8 68.9 2.1

NOTES:

OUTSIDE CONDITIONS ARE FOR CUTLER, ME AT 99% HEATING AND 1.0% COOLING.1.

2. INDOOR DESIGN TEMPERATURE HAS A +/-2°F DEADBAND AND A +/-5% RH DEADBAND. GLOBAL

SETPOINT MUST BE 73°F.

OUTDOOR AIR (OA) SCHEDULE (*3)

SPACES AREA OCCUPANTS

CALCULATED OA RATE

(CFM)

ZONEMARK

EQUIPMENT TOTAL

(CFM)

1 OFFICE 95 2 (*2) 15.7 20

2 MUD ROOM 60 0 3.6 10

HALLWAY

SIPRNET

BREAKROOM

40 0 (*1)

4 (*2)80 29.6

23.7

6 TOILET 50 0 0 (*1)

7 LAUNDRY 15 0 1.8 0 (*4)

8 SHOWER 30 0 0 (*1) 0

9 LOCKER ROOM 120 0 0 (*1) 0

NOTES:

*1. ONE OR MORE ROOMS ARE TREATED AS UNOCCUPIED WITH NO DIRECT OUTDOOR AIR.

*2. OCCUPANT LOADING IS FOR MECHANICAL CALCULATIONS PURPOSE ONLY. SEE LIFE SAFETY DRAWINGS FOR ACTUAL OCCUPANT LOADS.

*3. DEDICATED SPACES THAT ARE UNOCCUPIED AND SERVED BY DEDICATED UNITS SUCH AS CABINET UNIT HEATERS, GAS UNIT HEATERS, OR SPLIT SYSTEMS ARE

UNOCCUPIED WITH NO DIRECT OUTDOOR AIR.

*4. OUTDOOR AIR SUPPLIED THROUGH OPERABLE OPENING EXCEEDING 4% OF THE ZONE'S FLOOR AREA OR PERMANENT OPENING EXCEEDING 8% OF ZONE'S FLOOR AREA WITH THE CONNECTED ZONE SUPPLIED WITH AN EXCESS OF OUTSIDE AIR GREATER THAN THE SUM OF THE ZONES.

VC-AHU-1

INSPECTION OFFICE

SECURE ROOM

CORR

90 5.4

4 (*2)

0125 7.5

40.7

4 COMM 50 0 0 (*1)

IS-AHU-1

5 BREAKROOM 75 2 (*2) 14.5 30

6 RESTROOM 60 0 0 (*1) 0

7 WAITING 70 2 (*2) 14.2 15

8 STORAGE 60 0 3.6 0 (*4)

9 STOR/JAN 105 0 0 (*1) 0

10 MECH/ELEC 225 0 0 (*1) 0

11 GUARD HOUSE 45 1 (*2) 7.7 0 (*4)

VESTIBULE

WAITING

TOILET

170 30.2

4 (*2)

050 0 (*1)

3.6

4 ID/CHECK-IN 90 2 (*2) 15.4

VC-AHU-2

0 (*4)

ADMIN/COPY 135 2 (*2) 18.1 206

OFFICE 105 2 (*2) 16.3 207

INTERVIEW 105 2 (*2) 16.3 20

MOTHERING ROOM 80 2 (*2) 19.6 2010

JANITOR 15 0 0 (*1) 011

COMM ROOM 80 0 0 (*1) 0

DAYROOM 85 1 (*2) 10.1 15

MECH/ELEC 120 0 0 (*1) 013

HALLWAY 25 0 1.5 0 (*4)

DUCT CONSTRUCTION AND LEAKAGE TEST

SYSTEM

AIR HANDLING UNITS

EXHAUST FANS

DUCT PRESSURE CLASS (IN WG)

SUPPLY RETURN EXHAUST OUTSIDE AIR

+2.0 -1.0 N/A -1.0

N/A N/A N/A+1.0

DUCT

SEAL

CLASS

A

A

DUCT LEAKAGE CLASS

RECTANGULAR ROUND

DUCT TEST PRESSURE

(IN WG)

1.0

NOTES:

1. TEST 100% OF DUCTWORK. PRESSURE TESTS MUST NOT INCLUDE AIR HANDLING UNITS AND TERMINAL UNITS.

2. TEST IN ACCORDANCE WITH UFGS 23 05 93, TESTING, ADJUSTING, AND BALANCING FOR HVAC.

3. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS AND SMACNA HVAC AIR DUCT LEAKAGE TEST MANUAL.

1.0

SUPPLY FANS +1.0 N/A N/AN/A A 12 6 1.0

EXHAUST RATES

OCCUPANCY CATEGORY FIXTURE, EXHAUST AIR

RATE (CFM/UNIT)

AREA, EXHAUST AIR

RATE (CFM/SQ FT)

NOTES:

1. RATES SPECIFIED ARE BASED ON ASHRAE STANDARD 62.1-2019.

2. EXHAUST RATE FOR INSPECTION STATION JANITOR’S CLOSET IS PERFORMANCE BASED USING OFF VOLATILE

ORGANIC COMPOUND (VOC) SENSOR.

LOCKER ROOM (OTHER) 0.25-

TOILET (PRIVATE) - INTERMITTENT -50

JANITOR 1.0-

SHOWER -20

VENTILATION AND OCCUPANCY RATES

OCCUPANCY CATEGORY

PEOPLE OUTDOOR

AIR RATE

(CFM/PERSON)

PEOPLE OUTDOOR

AIR RATE (CFM/PERSON)

OCCUPANT

DENSITY

(PEOPLE/1000 SF)

STORAGE

CORRIDORS

OFFICE SPACE

0.06

0.06

0.065 5

NOTES:

1. RATES SPECIFIED ARE BASED ON ASHRAE STANDARD 62.1-2019.

BREAK ROOM

BARRACKS

5 0.12

0.065 20

LOBBY 5 100.06

LAUNDRY

GUARD STATION

5 0.12

0.065 15

DAYROOM 0.065 30

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:5

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-002

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

M E

C H

A N

IC

A

L C

R

IT

E R

IA

, C

O D

E S

A N

D S

TA

N

D A

R D

S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -0

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

294 358

12881076

A

D

T

0' 1'1'

1/2"=1'-0"

2' 3' 4' 5'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:0

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

MD101

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

F

LO

O R

P

LA

N

D E

M O

LI

T

IO

N

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M D

SCALE: 1/2" = 1'-0"

VISITOR CONTROL CENTER - FLOOR PLAN - DEMOLITION

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

DEMOLITION KEYNOTES#

A. PLANS ARE BASED ON NON-DESTRUCTIVE FIELD INVESTIGATION.

CONTRACTOR MUST VERIFY ALL FIELD CONDITIONS AND NOTIFY THE

OWNER/ENGINEER OF ANY DISCREPANCIES PRIOR TO PROCEEDING

B. DEMOLISH EXISTING HVAC EQUIPMENT AND ASSOCIATED APPURTENANCES

UNLESS OTHERWISE NOTED.

C. EQUIPMENT SIZES AND LOCATIONS SHOWN ARE APPROXIMATE.

D. REFER TO HAZARDOUS MATERIAL DRAWINGS PRIOR TO DEMOLITION. SEE

SHEET HM101 FOR MORE INFORMATION.

PLAN

NORTH

WALL MOUNTED HEATER IS EXISTING TO REMAIN.

DEMOLISH EXHAUST FAN AND ASSOCIATED APPURTENANCES INCLUDING,

BUT NOT LIMITED TO; DUCTING AND WALL CAP.

DEMOLISH AIR HANDLING UNIT AND ASSOCIATED APPURTENANCES

INCLUDING, BUT NOT LIMITED TO; DUCTING, GRILLES, DIFFUSERS, CUTOFF

SWITCHES, THERMOSTAT, AND PROPANE GAS PIPING. CAPTURE ALL

REFRIGERANT IN ACCORDANCE WITH THE CLEAN AIR ACT AMENDMENTS

OF 1990.

DEMOLISH LIQUID PROPANE PIPING. FOR MORE INFORMATION, SEE

PLUMBING SHEET PD101.

DEMOLISH CONDENSATE PUMP AND ASSOCIATED APPURTENANCES

INCLUDING, BUT NOT LIMITED TO; PIPES AND HOSES.

DEMOLISH OUTDOOR CONDENSING UNIT AND ASSOCIATED

APPURTENANCES INCLUDING, BUT NOT LIMITED TO; REFRIGERANT LINES

AND EQUIPMENT PAD.

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

295 358

12881077

PLAN

NORTH

3 3

0' 1'1' 1/2"=1'-0"

2' 3' 4' 5'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:0

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

MD102

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

B U

IL

D

IN

G

F

LO

O

R P

LA

N

D

E M

O

LI

T

IO

N

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M D

SCALE: 1/2" = 1'-0"

BUILDING 130 - FLOOR PLAN - DEMOLITION

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

DEMOLITION KEYNOTES#

A. PLANS ARE BASED ON NON-DESTRUCTIVE FIELD INVESTIGATION.

CONTRACTOR MUST VERIFY ALL FIELD CONDITIONS AND NOTIFY THE

OWNER/ENGINEER OF ANY DISCREPANCIES PRIOR TO PROCEEDING

B. DEMOLISH EXISTING HVAC EQUIPMENT AND ASSOCIATED APPURTENANCES

UNLESS OTHERWISE NOTED.

C. EQUIPMENT SIZES AND LOCATIONS SHOWN ARE APPROXIMATE.

D. REFER TO HAZARDOUS MATERIAL DRAWINGS PRIOR TO DEMOLITION. SEE

SHEET HM101 FOR MORE INFORMATION.

DEMOLISH AND LAWFULLY DISPOSE PACKAGE TERMINAL AIR CONDITIONING

UNIT AND ASSOCIATED APPURTENANCES. CAPTURE AND REMOVE ALL

CLASS 1 ODS REFRIGERANTS IN ACCORDANCE WITH THE CLEAN AIR ACT

AMENDMENT OF 1990.

DEMOLISH EXHAUST FAN AND ALL ASSOCIATED APPURTENANCES

INCLUDING, BUT NOT LIMITED TO; THE WALL CAP.

DEMOLISH WALL MOUNTED HEATER AND ALL ASSOCIATED

APPURTENANCES.

DEMOLISH LOUVER AND ALL ASSOCIATED APPURTENANCES .

DEMOLISH BASEBOARD HEATER AND ALL ASSOCIATED APPURTENANCES

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

296 358

12881078

A1

M-301

VC-EF-1

VC-EF-2

B

V

235 -

D

C

B

B

C

B

S

R

S

S

T

T

VC-AHU-1

VC-AHU-2

R

A

W

VC-EF-43

12"ø 16"ø

10"x14"

16"x12"

14"ø

W

W

T

FLOOR

E

OFFICE

SIPRNET

EXIST

MUD ROOM

BREAKROOM

110 TOILET

HALLWAY

TOILET

JANITOR

WAITING

VESTIBULE

ID/CHECK-IN

ADMIN/COPY

VC-ERH-1

"x

"x

W

W

6"x6"

VC-EUH-1

VC-EUH-2

SO

ATFP14"x14"

C1

M-303

A1

M-303

M -1

16"x16"

16"ø

"x

HALLWAY

14"x14"

16"x12" 10"x12"

12"x8"12"x8"

"x

HALLWAY

A B

3/8" = 1'-0"

1' 0' 1' 5' 10'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:1

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-101

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

F

LO

O R

P

LA

N A

R E

A A

M

E C

H A

N

IC

A L

H V

A C

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -1

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

SHEET KEYNOTES#

SCALE: 3/8" = 1'-0"

VISITOR CONTROL CENTER - FLOOR PLAN AREA A - MECHANICAL HVAC

KEY PLAN

PLAN

NORTH

A.

B.

C.

D.

E.

F.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST BE

SIZED BASED ON THE NECK SIZE UNLESS OTHERWISE NOTED. FOR SIZES,

SEE GRILLES, REGISTERS, AND DIFFUSERS SCHEDULE.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST

HAVE AN ACCESSIBLE VOLUME DAMPER.

FLEXIBLE DUCTWORK MUST NOT EXCEED 5' NOR EXCEED A 45 DEGREE

CHANGE IN DIRECTION. PROVIDE KINK FREE WITH A LIMIT OF ONE

FLEXIBLE CONNECTION.

CONDENSATE PIPING MUST BE 3/4"Ø AND SLOPED AT 1/8 INCH PER FOOT

UNLESS OTHERWISE SPECIFIED.

DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT

CONSTRUCTION STANDARDS.

SEE ARCHITECTURAL DRAWINGS FOR ROOF PENETRATION DETAILS.

ELECTRIC UNDER-TILE HEATING MUST BE PROVIDED TO COVER THE

FLOOR AREA OF ROOM 108. COORDINATE WITH CONSTRUCTION

SCHEDULE TO MEET MANUFACTURER'S RECOMMENDED INSTALLATION

CONDITIONS. THE IN-FLOOR RADIANT HEATING WIRE SPACING AND

LAYOUT MUST BE PER MANUFACTURER'S RECOMMENDATIONS AND

REQUIREMENTS.

MOUNT RECESSED WALL HEATER 1' AFF WHILE MAINTAINING

MANUFACTURER'S RECOMMENDATIONS AND REQUIREMENTS.

PROVIDE CABINET EXHAUST FAN WITH FLEXIBLE DUCTING AT UNIT

CONNECTION.

PROVIDE ALUMINUM WALL CAP WITH BACKDRAFT DAMPER.

THERMOSTAT CONTROLLING IN-FLOOR RADIANT HEATING SYSTEM MUST

BE CONNECTED TO FLOOR HEATING PER MANUFACTURER'S

RECOMMENDATIONS. THERMOSTAT TYPE MUST BE PER MANUFACTURER'S

REQUIREMENTS. COORDINATE WITH ARCHITECTURAL DRAWINGS.

PROVIDE TRANSFER GRILLES MOUNTED AT 7'-6" AFF.

MAKEUP AIR MUST BE PROVIDED THROUGH 3/4" UNDERCUT TO THE DOOR.

WALL MOUNTED UNIT HEATER IS EXISTING TO REMAIN.

S Y

M D

E S

C R

IP

TI

O N

D A

TE

A

P P

R

297 358

12881079

C3

A3

M-302

A

A

110-

A

A

R

VC-MS-1

VC-OU-1 VC-OU-2

D

RS/RL

VC-IU-1

2 2

T

VC-IU-1

SO

ATFP

S

A

R

R

100 -

R

C

VC-EF-3 3

18"ø

18"x20"16"x16"

18"x18"

14"x18"

14"x14"

20"ø

RS/RL

E

LAUNDRY

HALLWAY

LOCKER ROOM

COMM

HALLWAY

INTERVIEW

OFFICE

DAYROOM

MOTHER'S

SHOWER

18"x20"14"x24" 20"ø

"x

VC-EUH-3 7

4"ø DRYER DUCT

14"x18"

C1

M-303

A1

M-303

M -1

16"x12"

16"x16"

16"ø

16"ø

14"ø

16"x12"

M-401 A1

MECH/ELEC

117-

W

A B

3/8" = 1'-0"

1' 0' 1' 5' 10'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:2

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-102

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

F

LO

O R

P

LA

N A

R E

A B

M

E C

H A

N

IC

A L

H V

A C

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -1

SCALE: 3/8" = 1'-0"

VISITOR CONTROL CENTER - FLOOR PLAN AREA B - MECHANICAL HVAC

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

SHEET KEYNOTES#

KEY PLAN

PLAN

NORTH

A.

B.

C.

D.

E.

F.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST BE

SIZED BASED ON THE NECK SIZE UNLESS OTHERWISE NOTED. FOR SIZES,

SEE GRILLES, REGISTERS, AND DIFFUSERS SCHEDULE.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST

HAVE AN ACCESSIBLE VOLUME DAMPER.

FLEXIBLE DUCTWORK MUST NOT EXCEED 5' NOR EXCEED A 45 DEGREE

CHANGE IN DIRECTION. PROVIDE KINK FREE WITH A LIMIT OF ONE

FLEXIBLE CONNECTION.

CONDENSATE PIPING MUST BE 3/4"Ø AND SLOPED AT 1/8 INCH PER FOOT

UNLESS OTHERWISE SPECIFIED.

DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT

CONSTRUCTION STANDARDS.

SEE ARCHITECTURAL DRAWINGS FOR ROOF PENETRATION DETAILS.

PROVIDE WALL MOUNTED INDOOR UNIT MOUNTED APPROXIMATELY 8' AFF

TO BOTTOM OF UNIT WHILE MAINTAINING MANUFACTURER'S

RECOMMENDED CLEARANCES.

PROVIDE OUTDOOR UNIT ON CONCRETE HOUSEKEEPING PAD WHILE

MAINTAINING MANUFACTURER'S RECOMMENDED CLEARANCES. ROUTE

RS/RL PIPING AND CONTROL WIRING FROM OUTDOOR UNIT TO

ASSOCIATED INDOOR UNIT.

PROVIDE CABINET EXHAUST FAN WITH FLEXIBLE DUCTING AT UNIT

CONNECTION.

PROVIDE ALUMINUM WALL CAP WITH BACKDRAFT DAMPER.

PROVIDE DRYER DUCT ROUTED TO EXTERIOR ALUMINUM WALL CAP.

INSTALL PER MANUFACTURER'S RECOMMENDATIONS.

SUPPLY DUCTWORK STACKED OVER RETURN DUCTWORK. SEE SECTION

FOR MORE INFORMATION. COORDINATE DUCTWORK WITH ATTIC

STRUCTURE.

MOUNT RECESSED WALL HEATER 1' AFF WHILE MAINTAINING

MANUFACTURER'S RECOMMENDATIONS AND REQUIREMENTS.

S Y

M D

E S

C R

IP

TI

O N

D A

TE

A

P P

R

298 358

12881080

A B DC

3 IS-EF-1

IS-EF-2

IS-OU-1

A1

M-304

26"x8"

14"x8"

"x

18"x6"

C1

M-304

B

190 -

B

C

A

C

U

U

IS-MS-1

IS-IU-1

12"x10"

IS-AHU-1

W

E

18"x6"

6"x6"

6"x6"

8"x6"

IS-LV-2

D

RS/RL

D

RS/RL

18"x18"

T

T

A3

M-304

IS-AHU-1

IS-IU-1

18"x18"

COMM

MECH/ELEC

BREAKROOM

STOR/JAN

CORR

RESTROOM

STORAGE

WAITING

INSPECTION

OFFICE

IS-LV-1

IS-GV-1

IS-UH-1 9

10IS-EF-3

T

IS-EF-311

W

10"x6"

R

W

IS-EUH-1 13

RFI/SECURE

ROOM

VOC/H

IS-EF-2

IS-PTHP-1

B

14"x8"

0' 1' 5' 10' 15'1'

1/4"=1'-0"

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:3

:1

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \I n s p e c ti o n S ta ti o n

W

P

C u tl e r_

IS

M

E C

H R

.r v t

M-103

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

IN

S

P E

C T

IO

N

S

TA

T

IO

N

F

LO

O R

P

LA

N

M E

C H

A N

IC

A

L H

V A

C

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D C

C O

R E

M -1

SCALE: 1/4" = 1'-0"

INSPECTION STATION - FLOOR PLAN - MECHANICAL HVAC

PLAN

NORTH

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

SHEET KEYNOTES#

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST

BE SIZED BASED ON THE NECK SIZE UNLESS OTHERWISE NOTED. FOR

SIZES, SEE GRILLES REGISTERS, AND DIFFUSERS SCHEDULE.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST

HAVE AN ACCESSIBLE VOLUME DAMPER.

FLEXIBLE DUCTWORK MUST NOT EXCEED 5' NOR EXCEED A 45 DEGREE

CHANGE IN DIRECTION. PROVIDE KINK FREE WITH A LIMIT OF ONE

FLEXIBLE CONNECTION.

CONDENSATE PIPING MUST BE 3/4"Ø AND SLOPED AT 1/8 INCH PER FOOT

UNLESS OTHERWISE SPECIFIED.

DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT

CONSTRUCTION STANDARDS.

SEE ARCHITECTURAL DRAWINGS FOR ROOF PENETRATION DETAILS.

A.

B.

C.

D.

E.

F.

1 PROVIDE WALL MOUNTED INDOOR UNIT MOUNTED APPROXIMATELY 8' AFF

TO BOTTOM OF UNIT WHILE MAINTAINING MANUFACTURER'S

RECOMMENDED CLEARANCES.

PROVIDE OUTDOOR UNIT ON CONCRETE HOUSEKEEPING PAD WHILE

MAINTAINING MANUFACTURER'S RECOMMENDED CLEARANCES. ROUTE

RS/RL PIPING AND CONTROL WIRING FROM OUTDOOR UNIT TO

ASSOCIATED INDOOR UNIT.

PROVIDE UNIT WITH MANUFACTURER'S LIQUID PROPANE CONVERSION KIT.

SEE PLUMBING SHEET P-104 FOR PIPE ROUTING.

MOUNT UNIT ON MANUFACTURER SUPPLIED DUCTED PEDESTAL.

PROVIDE 3"Ø INTAKE AND 3"Ø FLUE WITH MANUFACTURER'S CONCENTRIC

VENT KIT AND DISCHARGE A MINIMUM OF 18" ABOVE ROOF'S SURFACE

MAINTAINING MANUFACTURER'S RECOMMENDED CLEARANCES.

PROVIDE CABINET EXHAUST FAN WITH FLEXIBLE DUCTING AT UNIT

CONNECTION.

PROVIDE ALUMINUM WALL CAP WITH BACKDRAFT DAMPER.

SUPPLY DUCTWORK STACKED OVER RETURN DUCTWORK. SEE SECTION

FOR MORE INFORMATION. COORDINATE DUCTWORK WITH ATTIC

STRUCTURE.

PROVIDE LIQUID PROPANE UNIT HEATER MOUNTED TO THE WALL AT 1' AFF

WHILE MAINTAINING MANUFACTURER'S RECOMMENDED CLEARANCES.

PROVIDE ROOF MOUNTED GRAVITY VENTILATOR WITH DAMPER AND

MANUFACTURER'S ROOF CURB. PROVIDE WITH 8"x8" DUCT ROUTED DOWN

TO 8'-6"' AFF WITH A MOTORIZED DAMPER.

PROVIDE INLINE EXHAUST FAN MOUNTED 6' AFF WITH FLEXIBLE DUCTING

AT UNIT CONNECTIONS.

PROVIDE 12" BY 12" LOUVER MOUNTED 8'-8" AFF.

MOUNT RECESSED WALL HEATER 1' AFF WHILE MAINTAINING

MANUFACTURER'S RECOMMENDATIONS AND REQUIREMENTS.

PROVIDE MOTORIZED DAMPER INTERLOCKED WITH IS-EF-3 EXHAUST FAN

VENTILATION OPERATION.

PROVIDE 1"x1" STAINLESS STEEL MESH SCREEN OVER DUCT OPENING.

PROVIDE MOTORIZED DAMPER INTERLOCKED WITH IS-AHU-1 AIR HANDLING

UNIT OPERATION.

PROVIDE EXHAUST FAN WITH INTEGRATED VOC SENSORS.

COORDINATE VENDOR SUPPLIED PACKAGE TERMINAL HEAT PUMP WITH

GUARD BOOTH MANUFACTURER TO MEET OR EXCEED 8.5 MBH HEATING AT

5°F AMBIENT.

MAKEUP AIR MUST BE PROVIDED THROUGH A 1" UNDERCUT TO THE DOOR

SEPARATING CORR 103 FROM RESTROOM 106.

MAKEUP AIR MUST BE PROVIDED THROUGH A 2" UNDERCUT TO THE DOOR

SEPARATING CORR 103 FROM STOR/JAN 109.

PROVIDE TRANSFER GRILLES MOUNTED AT 8'-6" AFF.

PROVIDE DDC PANEL MOUNTED 3' AFF.

S Y

M D

E S

C R

IP

TI

O N

D A

TE

A

P P

R

299 358

12881081

FINISH FLOOR

0' - 0"

TOP PLATE

9' - 6"

B

C

10"ø

16"x12" 16"x16"

WAITING

BREAKROOM

16"ø

C1

M-303

HALLWAY

8"ø 14"ø

W

FINISH FLOOR

0' - 0"

TOP PLATE

9' - 6"

A3

M-302

D

R S

/R L

"x

VC-AHU-1

HALLWAY

MECH/ELEC

VC-GV-1

RS/RL

18"x18"

20"x18"

18"x20"

20"ø

14"x18"

6"x10"

8"x8"

6"x6"

10"x10"

C1

M-303

OFFICE

3"Ø

5"Ø

R

D

"x

CONCENTRIC VENT

DDC

PANEL

3/8" = 1'-0"

1' 0' 1' 5' 10'

1' 3/4"=1'-0"

4'6" 0' 1' 2' 3'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:2

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-301

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

M E

C H

A N

IC

A

L S

E C

T

IO

N S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -3

SCALE: 1/2" = 1'-0"

VISITOR CONTROL CENTER - DUCTWORK SECTION

SCALE: 1/2" = 1'-0"

VISITOR CONTROL CENTER - MECHANICAL ROOM SECTION - EAST

C3

(M-102)

A1 (M-101)

S Y

M D

E S

C R

IP

TI

O N

D A

TE

A

P P

R

300 358

12881082

TOP PLATE

9' - 6"

A3

M-302

C1

M-303

VC-GV-1

VC-AHU-2

A

VC-LV-1

VC-LV-2

6"ø

20"ø

18"x14"

20"ø

5"ø

8"x8"

D

D

D

RS /RL

8"x8"

VC-SF-1

6"x6"

VC-UH-1

FINISH FLOOR

0' - 0"

TOP PLATE

9' - 6"

FINISH FLOOR

0' - 0"

TOP PLATE

9' - 6"

C3

M-301

VC-AHU-2

VC-AHU-1

14"x24" 14"x18"

20"ø

RS/RL

RS/RL

D

D

18"x20"

VC-LV-2

3"Ø 3"Ø

5"Ø

VC-SF-1

D

VC-LV-1

10"x10"

8"x8"

CONCENTRIC VENT

CONCENTRIC VENT

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:3

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-302

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

M E

C H

A N

IC

A

L S

E C

T

IO

N S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -3

SCALE: 3/4" = 1'-0" (M-401)

A1

VISITOR CONTROL CENTER - MECHANICAL ROOM SECTION - WEST

SCALE: 3/4" = 1'-0"

VISITOR CONTROL CENTER - MECHANICAL ROOM SECTION - NORTH

A3

(M-102)

S Y

M D

E S

C R

IP

TI

O N

D A

TE

A

P P

R

301 358

12881083

TOP PLATE

9' - 6"

C3

M-301

A1

M-301

B

A

R

V

D

235 -

W

E

105 -

S

350 -

C

C

VC-EF-3VC-EF-2

E

50 -

S

A

14"x10" 16"x16" 20"x18" 6"ø

VC-AHU-1

18"x18"12"x16"6"ø

6"x8"

12"x12"

12"x12"

HALLWAY

HALLWAY

OFFICE SIPRNET MUD ROOM TOILET LAUNDRY MECH/ELEC

LOCKER ROOM

BREAKROOM COMM

107 EXIST 108 111 113 117

110 116

VC-SF-1

VC-LV-2

9"x47"

12"x16"

8"x8"

18"x20"

14"x14"

VC-EUH-3

8"x8"

6"x6" 10"ø

6"x6"

10"ø

6"x6" ø8"

D

FINISH FLOOR

0' - 0"

TOP PLATE

9' - 6"

C3

M-301

A1

M-301

12"ø 16"ø 18"ø 20"ø

18"x14"14"x14"14"ø

S

C

B

B

R

180 -

B

A

60-

R

50 -

R

70 -

A

80 -

R

100 -

A

R

100 -

A

VC-EF-1

VC-EF-4-

W

VESTIBULE

ADMIN/COPY ID/CHECK-IN WAITING TOILET MOTHER'S DAYROOM OFFICE OFFICE

106 104 102 103 122 121 120 119

VC-SF-1

VC-LV-2

VC-LV-1

VC-AHU-2

8"ø 8"ø

8"x8"

6"x6"6"x6"

8"x8" 6"ø 8"x8" 6"ø 8"x8" 6"ø

8"x8"

6"ø 8"ø

VC-EUH-1

D

0' 1' 5' 10' 15'1'

1/4"=1'-0"

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:4

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-303

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

M E

C H

A N

IC

A

L S

E C

T

IO

N S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -3

SCALE: 1/4" = 1'-0"

VISITOR CONTROL CENTER - VC-AHU-1 SECTION

SCALE: 1/4" = 1'-0"

VISITOR CONTROL CENTER - VC-AHU-2 SECTION

GRAPHIC SCALE

C1

A1

(M-101/M-102)

(M-101/M-102)

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

302 358

12881084

C1

M-304

10"ø 26"x8"

C

FINISH FLOOR

0' - 0"

MASONRY TOP

10' - 8"

STOR/JAN

109BREAKROOM

18"x18"

COMM

IS-IU-1

2 43

A1

M-304

18"x18"

8"x26"

10"x16"

8"x14"

A3

M-304

12"x10"

FINISH FLOOR

0' - 0"

MASONRY TOP

10' - 8"

INSPECTION

OFFICE

BREAKROOM

MECH/ELEC

RFI/SECURE

ROOM

CORR

RESTROOM

C

18"x6"

IS-EF-1

6"x6"

10"ø

8"ø6"x8"

E

50-

W

6"x8" 18"x6"

"x

8"x6"

IS-LV-1

B

IS-UH-1

RS/RL

C1

M-304

IS-AHU-1

"x

18"x18"

RS/RL 3"ø

FINISH FLOOR

0' - 0"

MASONRY TOP

10' - 8"

IS-UH-1

IS-LV-2

IS-LV-1

IS-EF-3

IS-GV-1

"x

5"ø

R S

/R L

CONCENTRIC VENT

DDC

PANEL

D

3/8" = 1'-0"

1' 0' 1'

GRAPHIC SCALE

5' 10'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:3

:2

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \I n s p e c ti o n S ta ti o n

W

P

C u tl e r_

IS

M

E C

H R

.r v t

M-304

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

IN

S

P E

C T

IO

N

S

TA

T

IO

N

M E

C H

A N

IC

A

L S

E C

T

IO

N S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D C

C O

R E

M -3

SCALE: 3/8" = 1'-0" (M-103)

A1

INSPECTION STATION - DUCT SECTION VIEW - PLAN NORTH

SCALE: 3/8" = 1'-0" (M-103)

C1

INSPECTION STATION - DUCT SECTION VIEW - PLAN EAST

SCALE: 3/8" = 1'-0" (M-103)

A3

INSPECTION STATION - MECHANICAL ROOM SECTION

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

303 358

12881085

C3

A3

M-302

A1

M-302

VC-AHU-1

VC-AHU-2

VC-GV-1

VC-LV-1

VC-LV-2

VC-UH-1

1 2

1 2

RS/RL

RS/RL

D

D

D

MECH/ELEC

6"x6" 6"x6"

T

VC-SF-1

10"x10"

TO VC-OU-1

TO VC-OU-2

VC-SF-1

14"x24" 14"x18"

8"x8"

20"ø18"x20"

1"=1'-0"

1' 6" 0' 1' 2' 3'

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:5

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-401

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

V

IS

IT

O

R C

O N

T R

O L

C E

N

TE

R

E N

LA

R

G E

D M

E C

H A

N

IC

A L

P

LA

N S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -4

SCALE: 1" = 1'-0"

VISITOR CONTROL CENTER - ENLARGED MECHANICAL ROOM

GENERAL SHEET NOTES

GRAPHIC SCALE(S)

SHEET KEYNOTES#

A.

B.

C.

D.

E.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST BE

SIZED BASED ON THE NECK SIZE UNLESS OTHERWISE NOTED. FOR SIZES,

SEE GRILLES REGISTERS, AND DIFFUSERS SCHEDULE.

FINAL DUCT RUNOUTS TO GRILLES, REGISTERS, AND DIFFUSERS MUST

HAVE AN ACCESSIBLE VOLUME DAMPER.

FLEXIBLE DUCTWORK MUST NOT EXCEED 5' NOR EXCEED A 45 DEGREE

CHANGE IN DIRECTION. PROVIDE KINK FREE WITH A LIMIT OF ONE

FLEXIBLE CONNECTION.

CONDENSATE PIPING MUST BE 3/4"Ø AND SLOPED AT 1/8 INCH PER FOOT

UNLESS OTHERWISE SPECIFIED.

DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT

CONSTRUCTION STANDARDS

PROVIDE UNIT WITH MANUFACTURER'S LIQUID PROPANE CONVERSION

KIT. SEE PLUMBING SHEET P-102 FOR PIPE ROUTING.

MOUNT UNIT ON MANUFACTURER SUPPLIED DUCTED PEDESTAL.

PROVIDE 3"Ø INTAKE AND 3"Ø FLUE WITH MANUFACTURER'S CONCENTRIC

VENT KIT AND DISCHARGE A MINIMUM OF 18" ABOVE ROOF'S SURFACE

WHILE MAINTAINING MANUFACTURER'S RECOMMENDED CLEARANCES.

PROVIDE INLINE SUPPLY FAN MOUNTED 10'-7" AFF WITH FLEXIBLE

DUCTING AT UNIT CONNECTIONS.

PROVIDE MOTORIZED DAMPER INTERLOCKED WITH EXHAUST FAN SPACE

OPERATION.

ELECTRICAL EQUIPMENT SHOWN FOR REFERENCE.

PROVIDE 12" BY 12" LOUVER MOUNTED 10' AFF. LOUVER MUST PROVIDE

OUTSIDE AIR TO VC-AHU-1 AND VC-AHU-2. PROVIDE EACH BRANCH WITH A

VOLUME DAMPER AND MOTORIZED DAMPER. MOTORIZED DAMPER MUST

BE INTERLOCKED WITH ITS ASSOCIATED AIR HANDLING UNIT.

PROVIDE 18" BY 12" LOUVER MOUNTED 10'-6" AFF'.

CONDENSATE MUST BE ROUTED DOWN TO 3" AFF BEFORE DISCHARGE

WHILE MAINTAINING EQUIPMENT CLEARANCES.

PROVIDE LIQUID PROPANE UNIT HEATER MOUNTED 4'-6" AFF WHILE

MAINTAINING MANUFACTURER'S RECOMMENDED CLEARANCES.

PROVIDE ROOF MOUNTED GRAVITY VENTILATOR WITH DAMPER AND

MANUFACTURER'S ROOF CURB. PROVIDE WITH 8" BY 8" DUCT ROUTED

DOWN 6' AFF WITH A MOTORIZED DAMPER AND 1" BY 1" SCREEN OVER

DUCT OPENING.

PROVIDE 1" BY 1" MESH SCREEN OVER DUCT OPENING.

PLUMBING EQUIPMENT SHOWN FOR REFERENCE.

PROVIDE DDC PANEL MOUNTED 4' AFF.

A1 (M-102)

S Y

M D

E S

C R

IP

TI

O N

D A

TE

A

P P

R

304 358

12881086

MAIN DUCT

ROUND RUNOUTS RECTANGULAR RUNOUTS

SPIN-IN

FITTING

SA/OA

RA/EA

LOCKING TYPE

BRANCH DUCT

OPERATOR

MAIN DUCT

4" MIN.

BRANCH DUCT

SA/OA

RA/EA

MIN 3/8" SHAFT

ROUND DAMPER

STAND-OFF

MOUNTING BRACKET

LOCKING TYPE

OPERATOR

STAND-OFF

MOUNTING BRACKET

RECTANGULAR

DAMPER

MIN 3/8" SHAFT

NOTES:

1. STAND-OFF MOUNTING BRACKET MUST BE SIZED BASED ON DUCT INSULATION THICKNESS.

2. SHAFT MUST EXTEND THROUGH STAND-OFF MOUNTING BRACKET TO OPERATOR.

3. SHAFT MUST BE 1/2" FOR DUCTS 20" AND WIDER.

4. PROVIDE SHAFT BEARINGS FOR TIGHT JOINT BETWEEN SHAFT AND FRAME AT BOTH ENDS.

5. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS

45°

METAL STRAP

EYE BOLT WITH 2"

LONG FLAT BAR

3/8" BOLT WITH LOCKNUT

AND WASHER ON EACH

SIDE OF STRAP

(DUCT SIZE VARIES)

HANGER STRAP ONLY

METAL STRAP

INSULATION

INSULATED JACKET

INSULATION

(DUCT SIZE VARIES) SECURE TO BOTTOM AND

SIDES OF DUCT WITH SHEET

METAL SCREWS

METAL HANGER STRAP

SUPPORT FROM

STRUCTURE ABOVE

NOTES:

1. FOR HANGER STRAP GAUGE AND SPACING, SEE SMACNA LOW PRESSURE DUCT CONSTRUCTION STANDARDS.

2. FOR ATTACHMENTS TO STRUCTURE ABOVE, SEE SMACNA LOW PRESSURE DUCT CONSTRUCTION

STANDARDS.

3. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS

INSULATION SHIELD

TO ELECTRICAL POWER SOURCE

OUTDOOR UNIT

LIQUID PIPING

GAS PIPING

VINYL TAPE

REFRIGERANT LINES

(RS/RL) TO INDOOR UNIT

CONNECTING

CABLE MOUNT UNITS WITH

NEOPRENE PADS ON

HOUSEKEEPING PAD

NOTES:

1. COORDINATE WITH MANUFACTURER'S RECOMMENDED CLEARANCES.

2. PROVIDE PER MANUFACTURER'S WRITTEN INSTRUCTIONS.

3. SEE STRUCTURAL DRAWINGS FOR HOUSEKEEPING PAD DETAIL.

1. SEE DRAWINGS FOR DIMENSIONS, LENGTHS, AND TYPE.

2. WRAP GRILLE NECK AND PLENUM WITH R-6 FOIL-BACKED INSULATION.

3. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS

NOTE:

CONNECTION

HARD CEILING

OPPOSED BLADE DAMPER

SEAL WITH CAULKING

NECK W/SHEET METAL

SCREWS (4 MIN.) AND

ATTACH PLENUM TO GRILLE

TO GRILLE NECK

PLENUM BOX. SIZE ACCORDING

GRILLE NECK

VOLUME DAMPER WHERE INDICATED

PAINT INTERIOR BLACK

DUCT MAIN

LAY-IN CEILINGHARD CEILING

GRILLE (AS SPECIFIED)

LAY-IN CEILING

CONNECTION

GRILLE NECK

2. WRAP DIFFUSER NECK WITH R-6 FOIL-BACKED INSULATION.

1. SEE DRAWINGS FOR DIMENSIONS, LENGTHS, AND TYPE.

NOTE:

CONNECTION

HARD CEILING

HARD CEILING

DIFFUSER (AS SPECIFIED)

LAY-IN CEILING

LAY-IN CEILING

CONNECTION

DUCT MAIN

VOLUME DAMPER

FLEXIBLE DUCT CONNECTION

WHERE INDICATED (5' MAX)

3. WHERE PANS ARE INDICATED INSULATED THE BACK OF THE PAN.

4. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS

SOLID DUCT CONNECTION WHERE FLEXIBLE

DUCT ANGLE EXCEEDS 45°

ATTACH DUCT TO

DIFFUSER NECK

W/SHEET METAL

SCREWS (4 MIN.) AND

SEAL WITH CAULKING

INSULATION

STEEL PIPE

ROD

NUT (TYP)

BOLT AND

CLAMPING

STRAP

LENGTH AS REQUIRED

MULTIPLE PIPE RUNS

GALVANIZED STEEL CHANNEL

SADDLE (TYP)

STRUCTURE

AS REQUIRED)

CLEVIS HANGER (SIZE

THREADED

INSULATION SADDLE

SUPPORT FROM

STRUCTURE

THREADED ROD

SINGLE PIPE RUN

SUPPORT FROM

6" OR MORE

TO WALL EDGE (TYP)

WALL

INDOOR UNIT

6" OR MORE TO CEILING

7' MINIMUM ABOVE

FINISHED FLOOR

3/4"ø CONDENSATE DRAIN WITH

TRAP OR CONDENSATE PUMP REFRIGERANT LINES TO

OUTDOOR UNIT (INSULATE

SEPARATELY)

NOTES:

1. KEEP AT LEAST 4 INCHES UNDER THE UNIT FREE FROM OBSTRUCTIONS.

2. COORDINATE WITH MANUFACTURER'S RECOMMENDED CLEARANCES.

3. TERMINATE CONDENSATE DRAIN PIPE AS INDICATED ON PLANS.

4. PROVIDE PER MANUFACTURER'S WRITTEN INSTRUCTIONS.

1. SEE DRAWINGS FOR DIMENSIONS, LENGTHS, AND TYPE.

2. WRAP GRILLE NECK AND PLENUM WITH R-6 FOIL-BACKED INSULATION.

3. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS

NOTE:

CONNECTION

HARD CEILING

OPPOSED BLADE DAMPER

SEAL WITH CAULKING

NECK W/SHEET METAL

SCREWS (4 MIN.) AND

ATTACH PLENUM TO GRILLE

TO GRILLE NECK

PLENUM BOX. SIZE ACCORDING

GRILLE NECK

VOLUME DAMPER WHERE INDICATED

PAINT INTERIOR BLACK

DUCT MAIN

LAY-IN CEILINGHARD CEILING

GRILLE (AS SPECIFIED)

LAY-IN CEILING

CONNECTION

MINIMUM DUCT WIDTH OF PLENUM WIDTH + 2"

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:0

:5

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-501

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

M E

C H

A N

IC

A

L D

E

TA

IL

S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -5

SCALE: NOT TO SCALE

C1

DUCT BRANCH CONNECTION DETAIL

SCALE: NOT TO SCALE

C3

DUCTWORK SUPPORT DETAIL

SCALE: NOT TO SCALE

B1

OUTDOOR MINI/MULTI-SPLIT SYSTEM DETAIL

SCALE: NOT TO SCALE

A4

RETURN/EXHAUST GRILLE DETAIL

SCALE: NOT TO SCALE

A2

SUPPLY DIFFUSER DETAIL

SCALE: NOT TO SCALE

B2

TYPICAL PIPING SUPPORT DETAIL

SCALE: NOT TO SCALE

A1

WALL MOUNTED CASSETTE DETAIL

SCALE: 1/8" = 1'-0"

B4

RETURN/EXHAUST GRILLE (REDUCED VERTICAL CLEARANCE) DETAIL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

305 358

12881087

METAL STUD/SUPPORT

DUCT

GRILLE BLADES (45°)

DUCT FLANGE, ALL SIDES

GYP. BOARD

REGISTER DAMPER, IF APPLICABLE

VOLUME DAMPER IN

RUNOUT

MOUNTING SCREW

(TYP) INTO METAL

STUD/SUPPORT

GYP. BOARD

NOTES:

1. SIDEWALL MOUNTING SHOWN, CEILING MOUNTING SIMILAR.

2. FOR CEILING MOUNTED DIFFUSERS, SUPPORT DIFFUSER INDEPENDENT OF CEILING SYSTEM.

3. PROVIDE TRANSITIONS AS REQUIRED TO CONNECT DUCTWORK TO GRILLE NECK.

4. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS

FILL WITH ROCKWOOL

18 GAUGE DUCT SLEEVE

BACKER ROD (TYP)

DUCT WITH FIBERGLASS INSULATION. SIZE

VARIES, SEE PLAN

SEALANT AT PERIMETER

EXTERIOR

BACKER ROD

WATERPROOF

SEALANT

INTERIOR

INSULATION WITH

ALUMINUM JACKET

STAINLESS STEEL

DRAWBAND

INSULATION

PIPE

ESCUTCHEON PLATES WHERE

EXPOSED

WALL

PIPE SLEEVE (SET AND ANCHOR

DURING WALL CONSTRUCTION)PACK WITH FIBERGLASS AND

SEAL BOTH SIDES

INSULATION

PIPE

WALL

BACKER ROD

WATERPROOF SEALANT

PACK WITH FIBERGLASS AND

SEAL BOTH SIDES

EXCUTCHEON PLATES (BOTH

SIDES WHERE EXPOSED)

PIPE SLEEVE (SET AND ANCHOR

DURING WALL CONSTRUCTION)

CONCRETE SPLASH BLOCK

FINISH GRADE

CONDENSATE EXTERIOR

WALL

PIPE SUPPORT FROM

EXTERIOR WALL

LINE-HIDE

NOTES:

1. LINE HIDE COLOR MUST BE COORDINATED WITH ARCHITECT AND

PROVIDED TO APPEAR AS A GUTTER SYSTEM DESIGNED FOR FULLY

ENCLOSE EXTERIOR PIPING.

HARD CEILING

GRILLE

BACKDRAFT DAMPER

MOTOR WITH

VIBRATION

ISOLATOR

FAN HOUSING

FLEXIBLE DUCT

NOTES:

1. MOUNT BOTTOM OF CABINET EXHAUST FAN FLUSH WITH HARD CEILING SURFACE PRIOR TO GRILLE INSTALLATION.

MOUNTING SCREW (TYP)

FILTER

DUCTED PEDESTAL

RETURN AIR DUCT

FURNACE WITH BLOWER

COOLING COIL HOUSING

SUPPLY AIR DUCT

CONDENSATE PORTS

NOTES:

1. DUCTED PEDESTAL MUST BE A MINIMUM OF 6" IN HEIGHT.

2. CONCENTRIC VENT COMBUSTION AIR INTAKE MUST BE A MINIMUM OF 18"

ABOVE ROOF.

3. SIZE VENT (FLUE AND INTAKE) SIZES PER MANUFACTURER'S

RECOMMENDATIONS.

4. MOISTURE OVERFLOW SWITCH IN AUXILIARY CONDENSATE PORT MUST BE

WIRED TO SHUT-DOWN UNIT.

5. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION

STANDARDS

REFRIGERANT SUCTION PORT

REFRIGERANT LIQUID PORT

INTAKE

FLUE

VENT

COMBUSTION AIR INTAKE

ROOF BOOT

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:1

:0

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-502

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

M E

C H

A N

IC

A

L D

E

TA

IL

S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -5

SCALE: NOT TO SCALE

C1

CEILING AND SIDEWALL GRILLE CONNECTION DETAIL

SCALE: NOT TO SCALE

B2

TYPICAL NON-RATED WALL DUCT PENETRATION DETAIL

SCALE: NOT TO SCALE

A2

TYPICAL PIPE SLEEVE THRU EXTERIOR WALL DETAIL

SCALE: NOT TO SCALE

A1

TYPICAL PIPE SLEEVE THRU INTERIOR WALL DETAIL

SCALE: NOT TO SCALE

B1

SPLASH BLOCK DETAIL

SCALE: NOT TO SCALE

C2

CABINET EXHAUST FAN DETAIL

SCALE: NOT TO SCALE

A4

AIR HANDLING UNIT DETAIL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

306 358

12881088

FRAMING CAVITY

DUCT

LOUVER BLADES

JOINT SEALANT

(TYP.)

WALL EXTERIOR

NOTES:

1. DUCT CONSTRUCTION MUST COMPLY WITH SMACNA DUCT CONSTRUCTION STANDARDS.

2. CHECK BLADE ALIGNMENT AT THE VERTICAL JOINTS.

WALL INTERIOR

NOTES:

1. PROVIDE A MINIMUM OF 75% OF THE FLOOR AREA SERVED BY THE RADIANT FLOOR HEATER FREE FOR TILE ADHESIVE.

T

TILES

HEATING

CABLES

COPPER HEATING

CABLES (1/8"⌀)

THIN-SET

MORTAR

TILES

ADHESIVE

STRIP

ELECTRICAL

INSULATION

SLAB

NONCOMBUSTIBLE SLEEVE

NONCOMBUSTIBLE PIPE OR DUCT WITH

INSULATION. SIZE VARIES, SEE PLAN

ASTM E119 FLAME RESISTANT MATERIAL

FIRE RATED WALL

NOTES:

1. PENETRATION FIRESTOP SYSTEM MUST BE AN F RATING GREATER THAN OR EQUAL TO THE WALL'S F RATING.

2. SYSTEM MUST BE INSTALLED AS TESTED FOR ITS ASTM E814 OR UL1479 DETERMINED RATING.

SATISFACTORY TO DATE

APPROVED

ACTIVITY

FOR COMMANDER NAVFAC

SEAL

A/E INFO

A

B

C

D

1 2 3 4 5

1 2 3 4 5

A

B

C

D

SCALE:

CONSTR. CONTR. NO.

SHEET

NAVFAC DRAWING NO.

DES DRW CHK

OF

EPROJECT NO.:

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

DRAWFORM REVISION: 25 AUGUST 2020

PM/DM

BRANCH MANAGER

CHIEF ENG/ARCH

FIRE PROTECTION

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G S

Y S

T E

M S

C O

M M

A N

D

M

ID

-A T

LA

N

TI

C

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

AS NOTED

F

IL

E N

A M

E

L A

Y O

U T

N A

M E

P

L O

T T

E D

U

S E

R

03/09/2023

/8

/2

:1

:0

P M

U P ro je c ts

\2

\2 -0

C u tl e r, M E

P e ri m e te r S e c u ri ty

\0

S U

B M

IT

T

A L S

\0

F in a l S ig n e d

M a r

\R e v it \V is it o rs

C e n te r\

W

P

C u tl e r_

V C

M

E C

H R

.r v t

M-503

P -3

P

E R

IM

E

TE

R

S E

C U

R

IT

Y

M E

C H

A N

IC

A

L D

E

TA

IL

S

JDAJJN JJN

02/08/23

Approved by Jeffrey Hoyt, PWD ME, via Email

IM

P

R O

V E

M E

N

TS

CRH/LAF

1614700

N40085-19-D-9008 T008

C U

T

LE

R , M

A

IN

E

EJA

ALG

DSN

M

ID

L A

N T

D I

C O

R E

M -5

SCALE: NOT TO SCALE

A1

LOUVER PENETRATION DETAIL

SCALE: NOT TO SCALE

B1

RADIANT FLOOR HEATING DETAIL

SCALE: NOT TO SCALE

C1

TYPICAL FIRE RATED WALL PENETRATION DETAIL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

307 358

12881089

OUTDOOR

UNIT MARK

LOCATION TYPE

DX MINI SPLIT SYSTEM SCHEDULE

GENERAL NOTES:

A. PROVIDE AND CONNECT WIRING AND REFRIGERANT PIPING BETWEEN INDOOR AND OUTDOOR UNITS PER MANUFACTURER'S RECOMMENDATIONS.

B. PROVIDE WITH OZONE FRIENDLY REFRIGERANT SUCH AS R-410A OR APPROVED EQUAL.

C. PROVIDE ASHRAE 90.1 ENERGY COMPLIANT SYSTEM.

D. PROVIDE OUTDOOR UNIT WITH HAIL GUARD.

E. AIRFLOWS NOTED ARE FOR DRY COILS; WET COILS WILL BE SLIGHTLY LOWER.

F. EQUIPMENT MUST BE COATED TO MEET ASTM B117 3,000 HOUR SALT SPRAY TEST.

G. PROVIDE REMOTE, WALL MOUNTED DIGITAL, PROGRAMMABLE CONTROLLER.

H. PROVIDE WITH STANDARD WHITE CASSETTE, TOP RETURN GRILLE, WASHABLE FILTER, AND BOTTOM ADJUSTABLE DISCHARGE OUTLET GUIDE.

I. PROVIDE PETE'S PLUG ON INLET PIPING NEAR COIL.

VOLTS PHASE MCA

INDOOR

UNIT MARK MOCP

OUTDOOR UNIT

VOLTS PHASE MCA

INDOOR UNIT

AIRFLOW

(CFM)

ESP

(IN-WG)

SPEED

FAN DATA

NOMINAL

(MBH)

EAT

(°F DB/WB)

COOLING DATA

IS-MS-1 IS-IU-1

VC-IU-1

104 - COMM WALL MOUNTED 208 1 7 15208 1 1.0399 N/A HIGH 90 / 73

116 - COMM

TOTAL

(MBH)

13.612

WALL MOUNTED

NOMINAL

TONNAGE

VC-MS-1 208 1 7 15208 1 1.0399 N/A HIGH 90 / 7313.6121

NOMINAL

(MBH)

COP

HEATING DATA (AT 17°F)

6 2.25

6 2.25

SEER

15.0

15.0

1.0

SUPPLY FAN DATA

IS-AHU-1

MARK

(INDOOR UNIT)

3.5110 - MECHANICAL 1325 140 0.50 40.7

RPM

1075 35.7 81.3 63.3 55.1 52.4

COOLING COIL PERFORMANCE DATA

MOCPVOLTS

120 1

PHASE MCA

LOCATION

NOMINAL

OUTDOOR

UNIT

(TONNAGE)

SUPPLY

AIR

(CFM)

OUTDOOR

AIR

(CFM)

ESP

(IN-WG)

MOTOR

(HP)

TOTAL

CAPACITY

(MBH)

SENS.

CAPACITY

(MBH)

EDB °F EWB °F LDB °F LWB °F

15.014.1

GENERAL NOTES:

A. ALL CONTROLS SENSORS, ACTUATORS, WIRING, AND VFDS MUST BE PROVIDED BY CONTRACTOR.

B. PROVIDE MANUFACTURER'S LIQUID PROPANE CONVERSION KIT.

C. PROVIDE RETURN AND OUTDOOR AIR DAMPERS. ALL DAMPERS INTERNAL TO AHUS MUST HAVE ASTM B117 CONSTRUCTION FOR 3,000 HOUR SALT SPRAY TEST.

D. PROVIDE WITH UL 900 COMPLIANT 1" MERV 8 OR GREATER MEDIA FILTERS AT UNIT RETURN AIR CONNECTION.

E. SEE ELECTRICAL SPECIFICATIONS FOR MOTOR EFFICIENCY REQUIREMENTS.

F. PROVIDE PHASE MONITORING TO INCLUDE UNBALANCE PROTECTION, PHASE LOSS PROTECTION, AND PHASE REVERSAL.

G. PROVIDE REMOTE, WALL MOUNTED DIGITAL, PROGRAMMABLE CONTROLLER.

H. PROVIDE ASHRAE 90.1-2019 ENERGY COMPLIANT SYSTEM.

I. PROVIDE WITH OZONE FRIENDLY REFRIGERANT SUCH AS R-410A OR APPROVED EQUAL.

J. PROVIDE OUTDOOR UNIT WITH HAIL GUARD.

K. PROVIDE DUCT VIBRATION ISOLATORS AT EQUIPMENT CONNECTION.

L. PROVIDE FLEXIBLE PIPE CONNECTIONS AT EQUIPMENT CONNECTION.

M. PROVIDE WITH MANUFACTURER'S DUCTED PEDESTAL WITH SIDE RETURN AND FILTER BOX.

N. PROVIDE UL LISTED GAS TRAINS FOR EACH BURNER.

O. PROVIDE WITH MANUFACTURER'S CONCENTRIC VENT KIT WITH DUCTED VENT FLUE AND COMBUSTION INTAKE.

P. PROVIDE PETE'S PLUG ON INLET PIPING NEAR COIL.

DX SPLIT SYSTEM WITH DIRECT-DUCTED LIQUID PROPANE FURNACE SCHEDULE

0.75

VC-AHU-2 117 - MECHANICAL

1475 115 0.50 43.01075 37.6 79.2 62.0 120 1

0.75

VC-AHU-1 117 - MECHANICAL

1270 195 0.50 36.01075 29.8 78.6 63.1 120 13

15.012.0

15.012.0

3.5 55.0

55.2

51.7

52.6

FURNANCE PERFORMANCE DATA

MOCPVOLTS

208 3

PHASE MCA

ELECTRICAL DATA

208 3

208 3

INDOOR UNIT OUTDOOR UNIT

TYPE

INPUT

(MBH)

OUTPUT

(MBH)

LDB °F AFUEEDB °F

L. PROPANE 80.0 50.2 60.1 96.0 80%

L. PROPANE 60.0 41.4 59.4 85.6 80%

L. PROPANE 80%

SEER

14.0

14.0

14.0

IS-OU-1

MARK

(OUTDOOR UNIT)

VC-OU-2

VC-OU-1

62.5 50.0 57.0 96.1

GENERAL NOTES:

A. PROVIDE UL LISTED, ENERGY COMPLIANT PRODUCT.

B. PROVIDE WITH THERMAL OVERLOAD PROTECTION AND INTEGRAL DISCONNECT.

C. PROVIDE DUCT VIBRATION ISOLATORS AT EQUIPMENT CONNECTION.

UNIT NOTES:

1. PROVIDE WITH INTERLOCKED WITH LIGHTING FOR…