013001 submittal descriptions.doc

Section 01 30 01

SUBMITTAL DESCRIPTIONS

Part 1 – GENERAL

1.01 Related Documents

A.

Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section.

1.02

SUBMITTAL CLASSIFICATION

A.

Related Documents: Other requirements pertaining to submittals are included in:

1.

The Contract Clauses.

2.

Section 01 33 00 – Submittal Procedures.

B.

Submittals required by the Contract Clauses and other non‑technical parts of the Contract are not included in this Section.

C.

The submittals described below are those required and further described in other sections of the specifications.

1.

Submittal Description No. 1 (SD‑01) – Data: Submittals that provide calculations, descriptions, or documentation regarding the Work.

2.

Submittal Description No. 2 (SD‑02) – Not Used.

3.

Submittal Description No. 3 (SD‑03) – Not Used.

4.

Submittal Description No. 4 (SD‑04) – Drawings: Submittals that graphically show:

a.

Relationship of various components of the Work.

b.

Schematic diagrams of systems.

c.

Details of fabrication.

d.

Layouts of particular elements.

e.

Connections.

f.

Other relational aspects of the work.

5.

Submittal Description No. 5 (SD‑05) – Not Used.

6.

Submittal Description No. 6 (SD‑06) – Instructions: Preprinted materials describing installation of a product, system, or material, including special notices and material safety data sheets, if any, concerning impedances, hazards, and safety precautions.

7.

Submittal Description No. 7 (SD‑07) – Schedules: Tabular lists showing location, features, or other pertinent information regarding products, materials, equipment, or components to be used in the Work.

8.

Submittal Description No. 8 (SD‑08) – Statements: Documents, required of the Contractor, or through the Contractor from a Supplier, Installer, Manufacturer, or other lower tier Contractor, the purposes of which is to confirm the quality or orderly progression of a portion of the Work by:

Documenting procedures.

Acceptability of methods or personnel.

Qualifications.

Other verifications of quality.

9.

Submittal Description No. 9 (SD‑09) – Reports: Reports of inspections or tests, including analysis and interpretation of test results. Each report shall be properly identified, signed, and dated. Test methods used shall be identified and test results shall be recorded.

10.

Submittal Description No. 10 (SD‑10) – Not Used.

11.

Submittal Description No. 11 (SD‑11) – Not Used.

12.

Submittal Description No. 12 (SD‑12) – Not Used.

13.

Submittal Description No. 13 (SD‑13) – Certificates: Statements signed by an official authorized to certify on behalf of the Manufacturer of a product, system, or material, attesting that the product, system, or material meets specified requirements. The statement shall:

Be dated after the award of this Contract.

State the Contractor’s name and address.

Name the Project and its location.

List the specific requirements that are being certified.

14.

Submittal Description No. 14 (SD‑14) – Samples: Samples, including both fabricated and unfabricated physical examples of materials, products, and units of the Work – as complete units or as portions of units of the Work.

15.

Submittal Description No. 15 (SD‑015) – Not Used.

16.

Submittal Description No. 16 (SD‑16) – Not Used.

17.

Submittal Description No. 17 (SD‑17) – Not Used.

18.

Submittal Description No. 18 (SD‑18) – Records: Documentation required to record compliance with technical or administrative requirements.

19.

Submittal Description No. 19 (SD‑19) – Operation and Maintenance Manuals: Data that forms a part of an operation and maintenance manual.

PART 2 – PRODUCTS – Not Used PART 3 – Execution – Not Used

End of Section 01 30 01

THIS PAGE IS INTENTIONALLY BLANK.

01 30 01-2

SUBMITTAL DESCRIPTIONS

12910-330

Revised 3/2/09

12910-330

SUBMITTAL DESCRIPTIONS

01 30 01-1

Revised 3/2/09