Adec Submittal - VA Biloxi.pdf

DATE: 6/30/20

*ENTER CUSTOM CONTENT HERE*

Phone: 706.892.8725

Fax: 503.537.2702

E-mail: perry.greenway@a-dec.com

WARRANTY TERMS

PRODUCT LITERATURE

Biloxi, MS

A-dec Submittal Packet

DENTAL FURNITURE AND EQUIPMENT COORDINATION DOCUMENTS

PRODUCT DATA SHEETS

TRACK LIGHT INSTALLATION GUIDE

Submittal Packet Contents

COVER SHEET

Southeast School & Government Accounts

Perry Greenway

VA Biloxi - Renovate Bldg. 1

PROPOSAL/EQUIPMENT LIST

UTILITIES COORDINATION MATRIX

FLOOR PLANS

DENTAL FURNITURE PREINSTALLATION GUIDE YOUR REPRESENTATIVE:

A-dec Inc.

2601 Crestview Drive

Newberg, OR 97132

Customer Service: 800.547.1883 www.a-dec.com

Customer Name:

Reference:

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document Line Item Label 4 5531 D0670 Rear Console

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

5 5531 D0680 Side Console

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

6 5731 D0685 Upper Storage Side

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

7 5731 D0685 Upper Storage w/monitor mount Rear

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

8 5731 D0685A Upper Storage Cabinet Window Wall

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

9 5730 D0682 Dispensers - Left Hinge

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

10 5730 D0682 Dispensers - Right Hinge

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

11 577L D6050 Track Light

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Visual Document

12 5590 D0685B Storage Cabinet

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems with this document, please report them to us in writing. V797D-70087, exp. 02/09/2022

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems

Quote #:

Direct VA - Biloxi Biloxi VAMC

WQAQK000015-5

This written material is not intended to be, and should not be, used as a substitute for the compliance with local, state, federal code and Americans with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities. A-dec, Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning, the furnishings, performance or use this material. The information in this document is subject to change without notice. If you find any problems

- DATE:

LABEL Item Description JSN Log

Cat Qty AIR VAC DCW DHW DRAIN

PWR 110

VAC

VGA/

HDMI

CONDUIT

RACEWAY

MED

GAS

STRUCT

URAL

NOTES

1 511 DENTAL CHAIR D3320 CC 12 ✔ ✔ ✔Q 1" From chair floorbox to track light in ceiling

2 532 DOCTOR'S DEL SYSTEM D8250 CC 12 Includes built-in D9060 Prophylaxis Unit

3 551 ASST'S DELIVERY SYSTEM D8250 CC 12

4 5531.44 CONSOLE, NO SINK D0670 CC 12 Rear cabinet

5 5531.58 CONSOLE, SINK RT D0680 CC 24 ✔ ✔ ✔ ✔ ✔D Side cabinets

6 5731.34 WALL MNT UPR STRG D0685 CC 24 WALL Wood blocking required in wall - side

7 5731.34 WALL MNT UPR STRG D0685 CC 12 WALL Wood blocking required in wall - rear

8 5730.22 DISP UNIT D0682 CC 12 WALL Wood blocking required in wall - side

9 5730.22 DISP UNIT D0682 CC 12 WALL Wood blocking required in wall - side

10 577L LED TRACK LIGHT D6050 CC 12 ✔W CEILING Unistrut structure in ceiling

11 CUSTOM STORAGE CABINET D0685B CC 12

12 5744 OREGON MOBILE CAB D2520 CC 12

AIR Dental Air

VAC Dental Vacuum

DCW Domestic Cold Water

DHW Domestic Hot Water

CWS Central Water System

DRAIN Sink Drain

PWR

D

Duplex Receptacle, 20A, 110

VAC, GFCi per code

Q

Quad Receptacle, 20A, 110

VAC, GFCI per code

W

Whip, 20A 110 VAC Circuit, GFCI per code

X-RAY Per mfg.

MED GAS Per mfg.

Additional Notes:

A-DEC DENTAL TREATMENT ROOM EQUIPMENT AND DENTAL FURNITURE COORDINATION REFERENCE

VA Biloxi - Renovate Bldg. 1 Biloxi, MS 6/30/20

UTILITIES KEY TERMINATION NOTES

Perry Greenway

Southeast School & Government Accounts

Phone: 706.892.8725

Fax: 503.537.2702

E-mail: perry.greenway@a-dec.com

½" Copper Pipe, 90° Stop Valve, 3/8" Comp. (GC Provided/Installed) REFER TO TEMPLATES FOR LOCATION

5/8" OD Copper Pipe, capped REFER TO TEMPLATES FOR LOCATION

½" Copper Pipe, 90° Stop Valve, 3/8" Comp. (GC Provided/Installed) REFER TO TEMPLATES FOR LOCATION

½" Copper Pipe, 90° Stop Valve, 3/8" Comp. (GC Provided/Installed) REFER TO TEMPLATES FOR LOCATION

Sink Tail-Piece and P-Trap, Contractor-Provided/Installed REFER TO TEMPLATES FOR LOCATION

½" Copper Pipe, 90° Stop Valve, 3/8" Comp. (GC Provided/Installed) REFER TO TEMPLATES FOR LOCATION

As specified REFER TO TEMPLATES FOR LOCATION

As specified REFER TO TEMPLATES FOR LOCATION

Provide 4' whip. Upon installation, GC to hardwire whip to jct box supplied with product. Shield whip with flex MC

IMD SUPPLY

5B122

PANORAMIC

X-RAY

5B123

STERILE INSTR.

STORAGE

5B128

SOILED UTILITY

5B130

EQUIPMENT

STORAGE

5B135

UNISEX TOILET

5B136

DENTIST

WORKSTATIONS

5B129

HAC

5A110

ENGINEERING

5A111

MEDICATION

ROOM

5B109

SHIPPING/

RECEIVING ROOM

5B110

WEST STAIR

5B111

TOILET ROOM

5B112

SOILED UTILITY

5B114

5A109

CORRIDOR

5B100

CORRIDOR

5B101

AE121

AE121

DENTAL LAB

5B113

CST1-CUSTOM

CST1-CUSTOM

CST1-CUSTOM

CST1-CUSTOM

CST1-CUSTOM

C S

T C

U S

T O

M

C S

T C

U S

T O

M

C S

T C

U S

T O

M

WINDOW INTERF.WINDOW INTERF.

P A

S T

W

A L L

C S

T C

U S

T O

M

CST1-CUSTOM

57"

49"

38.25"

38.25"

38.25"

27"

27"

27"

27"

C S

T C

U S

T O

M

C S

T C

U S

T O

M

49.75"58"29"24.25"

49.75"58"53.25"

42.25" 58" 49.75"

49.75"58"29"13.25"

19.75"

19.75"

19.75"

19.75"

57"

41.75"

19.75" 27"

41.75"

19.75" 27"

49.75" 58" 45.75"

49.75" 58" 29" 16.75"

65.5" 68.25" 62.5" 70.5" 76.25" 90.25"

77" 86.25"

59.25" 70" 59.25" 68.5"

ELEVATION A

E L E

V A

T I O

N

B

E L E

V A

T I O

N

C

R r e l i a b l e c r e a t i v e s o l u t i o n s

SHEET NO.

DATE: 4-29-18

MCS

P R

E L

I M

I N

A R

Y

L

A Y

O U

T

F

O R

V A

B

I L O

X I

DRAWN BY:

2.25.14 24X36 MGN.5A-DEC SGI

MCSCHECKED:

PRELIMINARY FLOOR PLAN

AutoCAD SHX Text A5080

AutoCAD SHX Text A5106

AutoCAD SHX Text A5080

AutoCAD SHX Text A5080

AutoCAD SHX Text A5107

AutoCAD SHX Text X3150

AutoCAD SHX Text X6505

AutoCAD SHX Text R7250

AutoCAD SHX Text A5080

AutoCAD SHX Text M3150

AutoCAD SHX Text U0002

AutoCAD SHX Text P7650

AutoCAD SHX Text D0795

AutoCAD SHX Text D6600

AutoCAD SHX Text A1066

AutoCAD SHX Text A5075

AutoCAD SHX Text A5077

AutoCAD SHX Text A5075

AutoCAD SHX Text A5075

AutoCAD SHX Text A5077

AutoCAD SHX Text A5107

AutoCAD SHX Text A5077

AutoCAD SHX Text A5075

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 4/02

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 08/11

AutoCAD SHX Text 12/03

AutoCAD SHX Text 12/03

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 4/02

AutoCAD SHX Text 09/05

AutoCAD SHX Text 01/08

AutoCAD SHX Text 4/02

AutoCAD SHX Text This layout is conceptual in nature and proprietary to A-dec equipment. It is intended to be used solely with A-dec equipment and may not be disclosed, exploited, or reproduced for any other purposes without the express permission of A-dec. A-dec, Inc. does not guarantee compliance with accreditation policies or local, state, and/or federal codes, including, but not limited to, the Americans with Disabilities Act.

Perry.Greenway Highlight

Perry.Greenway Highlight

A-dec Dental Furniture

PRE-INSTALLATION GUIDE

For Preference Collection,® Preference ICC,® and Preference Slimline™

Copyright

© 2015 A-dec Inc. All rights reserved.

A-dec Inc. makes no warranty of any kind with regard to this mate-rial, including, but not limited to, the implied warranties of merchant-ability and fitness for a particular purpose. A-dec Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning the furnishing, performance or use of this material. The information in this document is subject to change without notice. If you find any problems in the documentation, please report them to us in writing. A-dec Inc. does not warrant that this document is error-free.

No part of this document may be copied, reproduced, altered, or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without prior written permission from A-dec Inc.

Trademarks and Additional Intellectual Property Rights

A-dec, the A-dec logo, A-dec 500, A-dec 300, Cascade, Cascade Master Series, Century Plus, Continental, Decade, ICX, ICV, Performer, Preference, Preference Collection, Preference ICC, and Radius are registered in the United States and other countries. A-dec 200, Preference Slimline, and reliablecreativesolutions are also trademarks of A-dec Inc. None of the trademarks or trade names in this document may be reproduced, copied, or manipulated in any manner without the express, written approval of the trademark owner.

Certain touchpad symbols are proprietary to A-dec Inc. Any use of these symbols, in whole or in part, without the express written consent of A-dec Inc., is strictly prohibited.

Regulatory Information

The Regulatory Information and Specifications document is delivered with A-dec dental device equipment as mandated by agency requirements.

If you need this information, please go to the Document Library at www.a-dec.com.

Product Service

For service information, contact your local authorized A-dec dealer. To find your local dealer, go to www.a-dec.com.

86.0142.00 Rev U 1

A-dec Dental Furniture Pre-Installation Guide

I N T R O D U C T I O N

This guide provides detailed technical information on electrical, utility, plumbing specifications, and diagrams, as well as mini templates.

Information presented in this document will assist you to:

• Specify required plumbing and utilities

• Specify framing and construction requirements

• Wire individual units

• Mount and secure cabinetry

2 86.0142.00 Rev U

A-dec Dental Furniture Pre-Installation Guide

T H I N G S T O N O T E

As you use this document to guide you through the technical specifications, note the following:

• The minimum requirements for attachment and for wall construction have been determined by an independent structural engineering company. Documented detail is available from A-dec.

• Shipping weights, hanging weights and mounting specifications in this document are for standard Preference products. Modifications or customizations may affect these specifications.

• Local regulations provide that licensed plumbers and electricians shall install utilities.

• All utilities must conform to NFPA, local fire codes and local regulations, as applicable.

• For the accessory consoles, utilities must be plumbed through the wall or subbase of the cabinet.

• There are several areas in the console subbase where the utilities can be plumbed.

• The drawings provided in this guide are for reference only. They are not drawn to scale.

Preference Collection® Return Policy

Preference Collection products cannot be returned for credit.

Accessory Console and Plumbing Templates

These templates included target symbols:

Indicates datum points for standard and optional stubs.

Indicates end of countertop or extent of console.

Document Information

Intended Audience

This guide is for contractors, plumbers, electricians, carpenters, designers, architects and others who are involved in designing and remodeling dental treatment rooms that accommodate Preference Collection products.

Consult a licensed professional, i.e. structural or architectural engineer, for mounting to metal studs or masonry walls. Ensure that all installations conform to local code requirements.

Disclaimer

This written material is not intended to be, and should not be, used as a substitute for compliance with local, state, federal code, and American with Disabilities Act. It is the responsibility of the user to integrate the A-dec equipment specifications presented herein with the regulations and codes overseen by local planning and inspection authorities.

CAUTION Consult a licensed professional, i.e. structural or architectural engineer, for mounting to metal studs or masonry walls.

86.0142.00 Rev U 3

INTRODUCTION

Other Sources of Information

Other Sources of Information

The A-dec Dental Furniture Pre-Installation Guide is just one offering in A-dec’s documentation set that provides technical product information, which covers proper installation and maintenance of Preference Collection. Other associated documents include:

A-dec Design Toolbox

Contains drawing and visualization blocks that you can use to quickly and efficiently layout a treatment room space.

Full-Size Templates

Provide accurate footprints for the Preference Collection and

Preference SlimlineTM product lines. They are designed to assist you in spotting and positioning A-dec products whether on the construction job site or in a completed treatment room. The full-size templates provide plumbing and utility locations, mounting clip positions, metal subbase structure and critical dimensions.

Installation Guides

Contain procedures designed to help you install Preference Collection cabinetry.

A-dec Equipment Catalog

Provides comprehensive product detail that walks you through identifying the cabinet models, choosing models and options and selecting accent and decor color

Pre-Installation Notes and Cautions

NOTE Job site construction should be completed before dental equipment installation (including finished floors, ceiling, plumbing, lighting, paint, etc.).

CAUTION Local regulation requires licensed plumbers and electricians to install utilities. All plumbing and utilities must conform to prevailing local codes.

CAUTION The manner and method for accessing utilities within the wall is the responsibility of the design team working on the project (dental dealer, architectural services, and contractors). Utilities must be accessible without the use of tools.

86.0142.00 Rev U 5

INTRODUCTION

Electrical Specifications Electrical Configuration

Electrical Configuration

Table 1. Operating Current for Ancillary Devices

Task Lighting

Power switch locations for Preference Collection task lights:

• Stack switch located on the 12 o’clock console

• Power switch located on each device: Doctor’s, Assistant’s, and 12 o’clock task light

Ancillary Device Operating Current (Amps)

@ 110-120 VAC

A-dec Preference Collection task light 0.3

A-dec 300-watt power supply 2.8

A-dec 17-watt power supply 0.2

Monitor, typical 1.1

Intraoral camera, typical 2.0

Curing light 2.0

Amalgamator, typical 2.3

Ultrasonic scaler, typical 0.9

X-ray viewer, typical 0.4

NOTE Connect incoming power to each cabinet to a 20-amp circuit breaker. Table 1 shows typical current draw for various devices that might be installed in a cabinet. Always consult device name plate for actual power requirements. Mobile equipment may have substantial power requirements and should be considered when determining total treatment room branch circuits.

6 86.0142.00 Rev U

F L O O R M O U N T I N G

Concrete Floors

Table 2. Concrete Floor Mounting Chart

Figure 2. Floor-Mounting - Concrete

Anchor Dimension A

Diameter Hole

Dimension B

Minimum Depth Fastener Part Number

Preference Collection Subbase Clips 1/2" (12.7 mm) 3-1/2" (88.9 mm) Stud, anchor, 1/2-13 x 5-1/2" 038.034.00

Preference ICC Leg Anchor 1/2" (12.7 mm) 3-1/2" (88.9 mm) Stud, anchor, 1/2-13 x 5-1/2" 038.034.00

5543 X-Ray Column Anchor 1/2" (12.7 mm) 3-1/2" (88.9 mm) Stud, anchor, 1/2-13 x 5-1/2" 038.034.00

A-dec 500® 541/545 Mount 1/2" (12.7 mm) 2-3/4" (69.9 mm) Stud, anchor, 1/2-13 x 4-1/4" 038.004.00

NOTE Dimension C per architectural drawings. Anchors are only approved for use in slabs greater than 5" (127 mm) thick. If concrete does not meet minimum requirements, consult with a licenced engineer for alternate anchors.

86.0142.00 Rev U 9

A-dec Dental Furniture Pre-Installation Guide

P R E F E R E N C E C O L L E C T I O N

Preference Collection is a complete line of modular dental furniture that can be custom configured to meet various needs.

This section of the Dental Furniture Pre-Installation Guide includes:

• Estimated Shipping Weights

• Wiring Diagrams

• Utility Specifications

• Loop Vent Diagram

• Mounting Specifications

• Framing Dimensions

• Framing Specifications

• Full-Size Template Reference

10 86.0142.00 Rev U

E S T I M A T E D S H I P P I N G W E I G H T S

Preference Collection

Table 4. Estimated Shipping Weights (laminate, solid surface / Quartz)

Model Number Pounds Kilograms

5562.34 500 227

5562.42 621 282

5662.34 424 192

5662.42 519 235

5580.42 677 / 692 307 / 314

5580.69 770 / 794 349 / 360

5580.96 930 / 964 422 / 437

5543.SP 920 / 940 417 / 427

5543.SB 1080 / 1090 490 / 495

5543.TB 1800 / 1810 816 / 823

5531.30 211 / 221 96 / 100

5531.44 296 / 310 134 / 141

5531.58 380 / 400 172 / 182

5531.72 475 / 499 215 / 227

5531.86 580 / 609 263 / 277

5731.22 60 27

5730.29 78 35

5732.43 223 101

5732.49 252 114

5731.22 85 39

Model Number Pounds Kilograms

5731.29 107 47

5731.34 116 53

5731.42 169 77

5631.30 165 / 175 75 / 80

5631.44 228 / 242 103 / 110

5631.58 291 / 311 132 / 141

5631.72 364 / 388 165 / 176

5631.86 447 / 476 203 / 216

12 86.0142.00 Rev U

5531 and 5731

5531 Accessory Console Floor-Mount

30", 44", 58", 72", and 86" w/sink

5731 Upper Storage Unit Wall-Mount

22", 29", 34", and 42" w/task light

Figure 5. Wiring Diagram - 5531 Accessory Console and 5731 Upper Storage Unit

Note: Provided if unit has floor plumbing.

86.0142.00 Rev U 15

PREFERENCE COLLECTION

Utility Specifications 5580, 5562, and 5662

U T I L I T Y S P E C I F I C A T I O N S

Table 5. Utility Specifications - Preference Collection

Utility Finish Requirement

Air Protrude 1" (25.4 mm) for 3/8" compression 80-125 psi (550 to 860 KPa), 2.5 scfm (71 sl/min) minimum, during normal use (7.5 scfm [210 sl/min] peak intermittent flow). Flush lines prior to making connections to dental equipment.

Water Protrude 1" (25.4 mm) for 3/8" compression 60 ± 20 psi (410 ±140 KPa), 1.5 gpm (5.7 l/min) minimum, not to exceed 40°C (104°F). Flush lines prior to making connections to dental equipment.

Central vacuum Protrude 1" (25.4 mm) for 5/8" (16 mm) O.D. tubing and other specified by the central vacuum supplier

Wet Systems: 10 ± 2 inches of Hg (34 ± 7 KPa) and 9 scfm (255 sl/min) minimum. Dry/Semi-dry Systems 4.5 ± 1 inches of Hg (16 ± 3.5 KPa) and 12 scfm (340 sl/min) minimum.

Electrical Protrude 1" (25.4 mm) Refer to the electrical requirements listed throughout this section.

Gravity drain Protrude 1" (25.4 mm) Basket strainer connects to 1-1/4" or 1-1/2" flanged tailpiece.

Nitrous Oxide Specified by the product manufacturer Specified by the product manufacturer.

Oxygen Specified by the product manufacturer Specified by the product manufacturer.

86.0142.00 Rev U 19

Mounting Specifications 5730 Dispenser Unit or 5731 Storage Unit

5730 Dispenser Unit or 5731 Storage Unit

Metal Studs

1-1/4" x 22 ga min

Top: 22" (558.8 mm), 29" (736.6 mm), 34" (863.6 mm), and 42" (1066.8 mm)

T.W. anchors in stud flange

Bottom: #9 x 2-1/4" S.D. screw in each stud

Wood Studs

Std or Better/D.F. or S.P.

Top: #10 x 3" wood screws

Bottom: #10 x 3" wood screws in each stud

WARNING For .22 or .29 modules (22-5/8" [574.7 mm] or 29-5/8" [752.5 mm] wide), you must mount the module anchor strips directly to wall studs in two locations (see Figure 12).

For .32 or .42 modules (34" [86.3 mm] or 42-1/8" [1070 mm] wide), you must mount the anchor strip directly to wall studs in a minimum of three locations (see Figure 12). If the ends of the anchor clip are more than 10" (254 mm) from a direct stud attachment, you must install an additional toggle bolt anchor to attach the anchor strip to the gypsum wallboard. Install the additional toggle bolt anchor approximately 10" (254 mm) from the direct stud attachment point.

If you cannot make the proper number of stud attachments, you must change the module position or reinforce the wall framing.

Refer to page 2 for required consultation.

20 86.0142.00 Rev U

Figure 11. 5730 and 5731 Mounting Cleat Attaching to Wall

Figure 12. 5730 and 5731 Mounting Specifications

68-1/2"

(1740 mm)

28 86.0142.00 Rev U

5531 and 5631 44" Accessory Console

Figure 18. Templates and Utilities - 5531 and 5631 44" Accessory Console

86.0142.00 Rev U 29

Templates and Utilities 5531 and 5631 58" Accessory Console

5531 and 5631 58" Accessory Console

Figure 19. Templates and Utilities - 5531 and 5631 58" Accessory Console

34 86.0142.00 Rev U

5531 and 5631 Wall-Mounted Utilities

Figure 24. Templates and Utilities - 5531 and 5631 Wall-Mounted Utilities

CEILING

LINE

CONC. SLAB ON

MTL "S"-DECK

P1000T UPPER RAILS

w/P1047 FITTINGS &

1/2"Øx5 1/2" KWIKBOLT

TZ CONC. ANCHORS

3 1/2" MIN. EMBEDMENT

P1000 VERT.

SUPPORTS W/

P2346 EA. END

P1000 LASH

RAILS w/P1068

FITTINGS

P1001 FIN.

RAILS

CEIL. BY

1/4" A.T.R.

P1000 DIAG.

BRACING w/

P1068 EA. END

BOT. OF

DECK

1/2"Øx3 3/4" KWIKBOLT TZ

CONC. ANCHORS 3 1/2"

MIN. EMBEDMENT

5'-4"

10"

1/2" PLYWOOD PALLET

SUPPLIED BY A-DEC

& INSTALLED BY

OTHERS

A,B

2.0

2.0

BRACING NOTE:

DIAGONAL BRACING SHOWN ARE

SUGGESTED LOCATIONS AND

MAY CHANGE DUE TO FIELD

CONDITIONS.

A

B

2.0

2.0

C

2.0

LEGEND

SYMBOL DESCRIPTION

P1000 DIAGONAL BRACES

P1000T UPPER RAILS

P1000 VERTICAL SUPPORT

P1000 LASH RAILS

P1001 FINISH RAILS

OTHERS 10

2'-6 1/2"

FIELD

VERIFY

9'-0"

FIELD

VERIFY

3"

1 2"

2"

2" perry.greenway Line perry.greenway Line perry.greenway Line perry.greenway Line perry.greenway Line perry.greenway Typewritten Text 1'-3" perry.greenway Typewritten Text perry.greenway Typewritten Text perry.greenway Typewritten Text perry.greenway Typewritten Text perry.greenway Text Box Foot Wall perry.greenway Line

Perry.Greenway Oval

A‐dec 511 Dental Chair

JSN D3320

A-dec, Inc., (800) 547-1883 https://www.a-dec.com/ E-mail: fedgov@a-dec.com or schools@a-dec.com Information subject to change. Rev 052919

PRODUCT DESCRIPTION

Chair for seating dental patient during dental procedures, providing patient comfort and support while maintaining ergonomic access for the dental provider team. Chair is adjustable: base and back move up and down to facilitate patient comfort and operator access.

A-dec 511 Chair shown with Seamless Upholstery.

Salient Characteristics Ultra-thin flexible back rest, measuring 1.25” thick on the seamless upholstery providing superior operator access to the oral cavity, reduces the chance of repetitive stress injury and provides excellent patient comfort and support over extended treatment periods.

Headrest, standard dual articulating with gliding cushion and quick release adjustment lever. (Also available in non-articulating Military “Bun” headrest version to accommodate regulation hairstyles for female personnel.)

2-position armrests, mounted mid-thigh position, design articulates forward for patient access. Robust design with durable Santoprene surface for comfort and ease of asepsis.

Lift range 13.5”-31.5” (Note: measurements are made from the floor to the bottom of the seat cushion.)

Chair swivels 60° (30° each side of center) enhances patient and operator accessibility.

Automatic Chair-Stop reduces risk of injury or damage to equipment when sensors detect obstruction. Lock-out feature disables chair movement when handpiece is in use.

Integrated 300 Watt power supply provides electrical requirements for chair-mounted dental light and ancillary products.

UL rated to 500LB. (227 kg) maximum patient load.

Accumulators in the hydraulic lift system provide a soft chair start and stop. Lift cylinders are guaranteed for ten years.

Self-diagnosing circuit board that is easily programmable, with “limp-along” lift activation.

Bi-directional hydraulic motor pump is compact and requires fewer service parts.

Cast iron base-plate, powder coat painted and sealed with an elastomeric polymer finish to prevent rust and scratch damage to the floor.

Vacuum-formed seamless upholstery is constructed of 40 ounces per yard/67 gauge superior grade vinyl. A-dec vinyl meets flammability specifications for: California Flammability Regulation 117-2013.

Virtual-Pivot design aligns the natural spine rotation of the seated patient with the chair’s rotational axis. This unique design feature maintains patient position and comfort throughout the chair’s entire range of motion.

Proudly manufactured and Assembled in Newberg OR, USA – certificate of origin available upon request.

UL Classified in USA and Canada. CE compliant.

A‐dec 511 Dental Chair

JSN D3320

A-dec, Inc., (800) 547-1883 https://www.a-dec.com/ E-mail: fedgov@a-dec.com or schools@a-dec.com

A-DEC PRODUCT SUPPORT

Local and Regional Territory Managers will provide project consultation and user-training.

A customer service representative is assigned specifically to each account.

Live technical support 0630-1630 (Pacific Time) Monday-Friday 1-800-547-1883.

95% of service parts can be shipped within 24 hours.

Repair parts will be available a minimum of 10 years after product obsolescence.

Space planning and architectural support provided at no extra cost.

Blanket-wrapped delivery service is available with pre-assembly at the factory, to minimize waste and speed up the installation process.

Installation service is available by a trained and experienced crew.

Technical repair training and certification is offered free of charge at the factory 4-7 times a year. Each class is 3 days in duration. Room, board and class cost is covered by A-dec.

Transportation to Portland, Oregon not included.

Service parts guides updated annually and available in both hard copy and electronic.

ADDITIONAL SUPPORTING DOCUMENTATION

Regulatory Information, Specifications, and Warranty (part #86.0221.00) A-dec 511 Instructions for Use (part # 86.0761.00) A-dec 511 Pre-Installation guide (part # 86.0753.00) A-dec 511 Installation guide (part# 86.0648.00) A-dec 311/411/511 Dental Chairs Service Guide (part # 86.0380.00) A-dec 311/411/511 Dental Chairs Service Reference (part # 86.0381.00)

Documents can be obtained online at https://www.a‐dec.com/ in our Resource Center, or by contacting A-dec Customer service at (800) 547-1883 or fedgov@a-dec.com or schools@a-dec.com

Contact your A-dec Territory Manager for questions, pricing and configuration options (https://www.a-dec.com/schools-and-government)

A‐dec 532 Delivery System

JSN D8250

A-dec, Inc., (800) 547-1883 www.a-dec.com E-mail: fedgov@a-dec.com or schools@a-dec.com

Chair-mounted delivery system is a compact, adjustable control unit that positions dental instruments in relation to the operator and typically includes pneumatic, electrical, data and water control systems required for the proper function of air-water syringe(s), high and low speed handpiece(s), electric motor(s), scaler(s), curing light(s) and intra oral camera(s).

A-dec 532 traditional style chair-mounted delivery system shown with optional clinical devices and standard touch pad.

Salient Characteristics

Integrated four position handpiece control block is capable of operating up to four active handpiece positions and is constructed of plated lead-free brass (per section 14.17 of the Safe Drinking Water Act). Each handpiece position has an individual drive air and water adjustment. Removable water cartridge valves allow for quick and easy servicing of block. A single sliding locking tab secures the handpiece tubing to the control block requiring no tools and allows easy access to connect or disconnect tubing. Unique water-flow system eliminates dead ends that can harbor stagnant water.

Positive Positioning lets doctors smoothly place the delivery where they want—and keeps it in place.

LED Coolant indicator lights up when a handpiece is lifted out of the holder, so there’s no more second guessing which knob to use when making adjustments.

Customizable placement with six positions on the control head, so doctors can integrate almost any devices they choose.

Removable tray holder is integrated stackable and customizable.

Left/Right convertible without the use of tools.

Data Control System (DCS) is used to control all of the electrical components (fiber optics, heated syringe, touch pad, camera, electric micro-motors, and dental light). The DCS allows plug and play add-ons.

Chair lockout stop feature prevents the accidental movement of the chair when a handpiece or instrument is in use.

Silicone handpiece tubing contains anti-microbial AlphaSan® and quick-disconnects secured to the control block. Lighter, more flexible and more durable than vinyl tubing.

A 2.0 liter, quick-connect water bottle is designed with an interior pickup tube which reduces the chance of cross-contamination.

The system flush toggle has a flow-through design that eliminates stagnant water and flushes all tubings simultaneously.

All interior water lines used throughout delivery system contain anti-microbial AlphaSan® which protects against microbial colonization on interior and exterior surfaces.

The control head provides ample space to integrate up to six clinical devices.

The flex arm enables easy routing of cables and tubings.

USB extension cable is provided in delivery system umbilical.

Handpiece holders are independently adjustable a full 45 degrees to allow precise positioning of instruments.

A quad-volt intra-oral light source provides up to four independently adjustable output voltages to accommodate intra-oral illumination.

The deluxe touchpad is center mounted for easy left- or right-handed access and offers expanded functions required for specialized instruments, such as electric micro-motor(s), programmable endodontic motor(s), ultrasonic instrument(s), etc. The screen provides help in troubleshooting and system diagnostics.

Proudly manufactured and assembled in Newberg OR, USA – certificate of origin available upon request.

UL Classified in USA and Canada. CE compliant.

Local and regional Territory Managers will provide project consultation and user-training.

A customer service representative is assigned specifically to each account.

Live technical support 0630-1630 (Pacific Time) Monday-Friday at 1-800-547-1883.

95% of service parts can be shipped within 24 hours.

Repair parts will be available a minimum of 10 years after product obsolescence.

Space planning and architectural support provided at no extra cost.

Blanket wrapped delivery service is available with pre-assembly at the factory to minimize waste and speed up the installation process.

Installation service is available by a trained and experienced crew.

Technical repair training and certification is offered free of charge at the factory 4-7 times a year. Each class is 3 days in duration. Room, board and class cost is covered by A-dec.

Transportation to Portland, Oregon is not included.

Service parts guides updated annually and available in both hard copy and electronic.

ADDITIONAL SUPPORTING DOCUMENTATION

Regulatory Information, Specification & Warranty (part #86.0221.00) A-dec 532 Instructions for Use (part # 86.0759.00) A-dec 532 Pre-Installation guide (part # 86.0753.00) A-dec 532 Installation Guide (part# 86.0479.00) A-dec 500 Service Guide (part # 86.0812.00) A-dec 500 Service Reference (part # 86.0383.00)

Documents can be obtained online at www.a-dec.com in our document library, or by contacting A-dec Customer service at (800) 547-1883 or fedgov@a-dec.com or schools@a-dec.com configuration options (https://www.a-dec.com/schools-and-government)

A-dec 551 Assistant’s Instrumentation Chair-Mounted

Included with JSN# D8250

Information subject to change. Rev. 011516

The A-dec 551 Assistant’s Arm is a chair-integrated delivery for Air-Water Syringe, High Volume Evacuator (HVE), Saliva Ejector (SE) and optional ancillaries (curing light or warm water syringe). It is highly flexible and adjustable to accommodate both two and four handed dentistry. Includes Integrated touch pad, and built in solids collector. Included with JSN#8255.

A-dec 551 Assistant’s Instrumentation shown with Long Arm choice and optional dual HVE.

Salient Characteristics

• Articulated 6-axis arm (long arm) and 5-axis (short arm) allows for vertical and horizontal adjustments and greater than 270° range of positioning of the assistant’s instrumentation, promoting improved ergonomics and safety for the assistant , and accommodating both two and four handed dentistry.

• Vertical movement of 22.75" (short arm) to a horizontal movement of 36" (long arm).

• Multiple holder configurations including 3-position, 4-position, or dual 2-position.

• Individually articulating holders for maximum flexibility in instrument positioning.

• Long arm and short arm versions provides options to suit all requirements.

• Integral solids collector with fine mesh screen to trap materials from entering vacuum system and is easily maintained.

• Modular, push-on connections on both ends of vacuum tubings for reliable seal and easy maintenance.

• Standard multi-function touchpad provides secondary control of the chair, light, and accessory functions. Designed to be used as a handle for easy positioning of the assistant’s arm.

• Capability of holding ancillary devices (such as curing light, warm water syringe, etc…).

• Mounts only to A-dec 511 or A-dec 411 dental chair.

• Proudly manufactured and assembled in Newberg, OR, USA – certificate of origin available upon request.

• UL Certified in Canada and United States. CE certified in EU.

http://www.a-dec.com/ mailto:fedgov@a-dec.com mailto:schools@a-dec.com

A-dec 551 Assistant’s Instrumentation Chair-Mounted

Included with JSN# D8250

Information subject to change. Rev. 011516

• Local and Regional Territory Managers will provide user-training and project consultation.

• A customer service representative is assigned specifically to each account.

• Live technical support 0630-1630 (Pacific Time) Monday-Friday at 1-800-547-1883.

• 95% of service parts can be shipped within 24 hours.

• Repair parts will be available a minimum of 10 years after product obsolescence.

• Technical repair training and certification is offered free of charge at the factory 4-7 times a year to choose from. Each class is 3 days in duration. Room, board and class cost is covered by A-dec. Transportation to Portland, Oregon not included.

• Installation service is available by a trained and experience crew.

• Blanket-wrapped delivery service is available with pre-assembly at the factory to minimize waste and speed up the installation process.

• Service parts guides updated annually and available in both hard copy and PDF.

• Product Independently Evaluated by USAF DECS, available upon request

• Regulatory Information and Specifications (part #86.0221.00)

• Instructions for Use (part # 86.0603.00)

• A-dec 551 Pre-Installation guide (part # 85.0052.00)

• A-dec 551 Installation Guide (part # 86.0388.00, 86.0400.00)

• A-dec 500 Service Guide (part # 86.0348.00)

• Expanded technical specifications including features and benefits

Documents can be obtained online at www.a-dec.com in our document library, or by contacting A-dec Customer service at (800) 547-1883 or fedgov@a-dec.com or schools@a-dec.com

Contact your A-dec Territory Manager for questions, pricing and configuration options (http://us.a-dec.com/en/Company/Contact-Us/Schools-and-Government/Schools- Representatives) http://www.a-dec.com/ mailto:fedgov@a-dec.com mailto:schools@a-dec.com http://www.a-dec.com/ mailto:fedgov@a-dec.com mailto:schools@a-dec.com http://us.a-dec.com/en/Company/Contact-Us/Schools-and-Government/Schools-Representatives http://us.a-dec.com/en/Company/Contact-Us/Schools-and-Government/Schools-Representatives

A-dec 577L Track-Mounted Dental Light

JSN # D6050

A-dec, Inc., (800) 547-1883 www.us.a-dec.com E-mail: fedgov@a-dec.com or schools@a-dec.com

Information subject to change. Rev. 012814

Dental operating light used to illuminate the field of work. This is a single light unit on a cantilever arm suspended from a moving trolley in a ceiling track. The light can be used in installations where the ceiling height is between 8 and 10 feet.

Physical dimensions refer to the light's maximum travel dimensions centered on the ceiling mounting track. The weight includes the light, arm and trolley. Mounting this light may require reinforcing the ceiling or hanging the mount from the underside of the reinforcements above a suspended ceiling.

A-dec 577L LED Track-Mounted Dental Light.

Salient Characteristics

• Three axis barycentric positioning. The entire light head rotates a full 540 degrees (1 ½ turns) of horizontal rotation. The Optics Head rotates 120° total (15° up, 105° down), the Optics Head rotates 80° (±40° from vertical).

• Three intensity settings (15,000/25,000/30,000lux)(1,394/2,323/2,787fc).

• Cure-safe composite setting (25,000lux(2,323fc)/yellow): provides a “yellow” light providing ample illumination in the oral cavity without the premature curing of photo-initiated dental composites.

• Color Temperature/Color Rendering Index: 5,000K/~90 CRI for accurate color rendering and tissue analysis.

• Ability/ease of positioning: Rotation axis about the rigid arm to flex arm interface: There is

315° of travel. The vertical travel shall be achieved via the parallel link system in the flex arm.

This travel is to be 27.9 inches (71.1cm).

• Flexible, fracture resistant handles stay cool to touch, provide positive tactile feel, and protect head from potential impact damage.

• Thermal energy output: 24 BTU/hr. nominal at High intensity. 15 Watt power consumption.

No bulb replacement.

• Orbital LED array on aluminum-cored chassis dissipates heat passively, no hot surfaces or handles and does not require a cooling system or fan.

• Full touchpad control of light modes with auto on/off capabilities on A-dec’s DCS touch pads.

• Pattern and shadowing: “Stadium” style LED array minimizes shadowing due to blockage from instruments and the dental team. When properly focused, the light pattern at 700 mm is 100mm x 145mm at 10% of the maximum intensity. The illumination shall decrease in intensity progressively and smoothly toward the pattern edge.

• Smooth surface exterior parts are able to be cleaned and barrier protected without damage to the light surface or markings.

• UL Classified in USA and Canada. EC compliant.

A-dec 577L Track-Mounted Dental Light

JSN # D6050

Information subject to change. Rev. 012814

• A customer service representative is assigned specifically to each account.

• Live technical support 0630-1630 (Pacific time) Monday-Friday at 1-800-547-1883.

• 95% of service parts can be shipped within 24 hours.

• Repair parts will be available a minimum of 10 years after product obsolescence.

• Technical repair training and certification is offered free of charge at the factory 4-7 times a year to choose from. Each class is 3 days in duration.