Amendment 11_d - Revised Section 00 01 15 List of Drawings 5-7-24.pdf

Fire Island Inlet to Jones Inlet, NY-Navigation FIIJI24

DOCUMENT 00 01 15 Page 1

SECTION TABLE OF CONTENTS

DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS

SECTION 00 01 15

LIST OF DRAWINGS

01/07

PART 1 GENERAL

1.1 SUMMARY

1.2 CONTRACT DRAWINGS, MAPS, AND SPECIFICATIONS

PART 2 PRODUCTS

PART 3 EXECUTION

-- End of Section Table of Contents --

DOCUMENT 00 01 15 Page 2

SECTION 00 01 15

LIST OF DRAWINGS

01/07

PART 1 GENERAL

1.1 SUMMARY

This section lists the drawings for the project pursuant to contract clause "DFARS 252.236-7001, Contract Drawings, Maps and Specifications."

1.2 CONTRACT DRAWINGS, MAPS, AND SPECIFICATIONS

(a) The Government will provide to the Contractor, without charge, one (1) sets of contract drawings and specifications, except publications incorporated into the technical provisions by reference, in electronic or paper media as chosen by the Contracting Officer.

(b) The Contractor shall-

(1) Check all drawings furnished immediately upon receipt;

(2) Compare all drawings and verify the figures before laying out the work;

(3) Promptly notify the Contracting Officer or Contractor Officer's Representative of any discrepancies;

(4) Be responsible for any errors that might have been avoided by complying with this paragraph (b); and

(5) Reproduce and print contract drawings and specifications as needed.

(c) In general:

(1) Large-scale drawings shall in general govern over small-scale drawings. Information and data provided in contract specifications shall govern over similar information and data specified in contract drawings; and

(2) The Contractor shall follow figures marked on drawings in preference to scale measurements.

(d) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve the Contractor from performing such omitted or misdescribed details of the work. The Contractor shall perform such details as if fully and correctly set forth and described in the drawings and specifications.

(e) The work shall conform to the following contract drawings and maps, all of which form a part of these specifications and are available in the office of the District Engineer, U.S. Army Corps of

DOCUMENT 00 01 15 Page 3

Engineers, New York District, 26 Federal Plaza, New York, N.Y.

10278-0090:

Contract drawings are as follows:

Fire Island Inlet and Shores Westerly to Jones Inlet, New York Beach Erosion Control and

Navigation Project

- Option : Overlook Beach

SHEET NO.

DESCRIPTION

COVER & INDEX

GENERAL LOCATION MAP AND

DETAILS

CHANNEL & DEPOSITION

BASINS - DREDGING

LIMITS & PRISM

GENERAL NOTES AND ALIGNMENT

DATA

LAYOUT & DESING OF

PLACEMENT AREA

(STA. 0+00 to 26+00)

LAYOUT & DESIGN OF

(STA. 26+00 to 55+00)

(STA. 55+00 to 84+00)

DOCUMENT 00 01 15 Page 4

(STA. 84+00 to 113+00)

(STA. 113+00 to 142+00)

(STA. 142+00 to 171+00

PROFILES

(STA. 3+00 to 27+00)

(STA. 30+00 to 54+00)

(STA. 57+00 to 81+00)

(STA. 84+00 to 108+00)

(STA. 111+00 to 135+00)

(STA. 138+00 to 162+00)

OPTION 4

BEACH PLACEMENT AT OVERLOOK

BEACH

OP - 1:LEGEND, LAYOUT AND

DESIGN OF PLACEMENT AREA

PLACEMENT AREA PROFILE

(12+00 - 15+00)

(16+00 - 19+00)

DOCUMENT 00 01 15 Page 5

OPTION 5

BEACH PLACEMENT AT OVERLOOK

OP - 1:LEGEND, LAYOUT AND

DESIGN OF PLACEMENT AREA

(12+00 - 15+00)

(16+00 - 19+00)

OPTION 6

BEACH PLACEMENT AT TOBAY

OVERALL SITE PLAN

TOBAY BEACH PLAN

AREA 1

(STA 80+00 – STA 85+00)

(STA 90+00 – STA 95+00)

(STA 100+00 – STA 105+00)

(STA 110+00)

PLAN

(STA 85+00 to STA 90+00)

(STA 90+00 to STA 95+00)

DOCUMENT 00 01 15 Page 6

(STA 95+00 to STA 100+00)

(STA 100+00 to STA 105+00)

(STA 105+00 to STA 110+00)

(STA 110+00 to STA 115+00)

(f) The Contractor shall check all drawings furnished to him immediately upon their receipt and shall promptly notify the Contracting Officer or Contracting Officer's Representative of any discrepancies. Figures marked on drawings shall in general be followed in preference to scale measurements unless dimensions are specified.

Large-scale drawings shall in general govern over small-scale drawings. Information and data provided in contract specifications shall govern over similar information and data specified in contract drawings. The Contractor shall compare all drawings and verify the figures before laying out the work and will be responsible for any errors which might have thereby been avoided (DOD FAR Suppl.

52.236-7002).

PART 2 PRODUCTS

Not Used.

PART 3 EXECUTION

Not Used.

-- End of Section --