J14--Submarine_Maintenance_Standard_6310-081-015 _Submarine_Preservation.pdf

FOR OFFICIAL USE ONLY

SUBMEPP

MS NO. 6310-081-015 REV I CHG-2

SUBMARINE

MAINTENANCE

STANDARD

MRDESCRIPTION: Submarine Preservation General Painting

DESTRUCTION NOTICE. Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

SUBMEPPAPPROVAL

Martha M. Bowman

SYSTEM/COMPONENT ENGINEER/TECHNICIAN

Cynthia L. Waters 6/19/14

PROGRAMMANAGER DATE

DISTRIBUTION STATEMENT D. Distribution authorized to DOD and DOD contractors only (Administrative/Operational use). Other requests shall be referred to COMNAVSEASYSCOM or higher DOD authority.

Class: SSN688, SSN21, SSBN726, SSGN726, SSN774, MTS626, MTS635

MS NO. 6310-081-015 REV I CHG-2 PAGE i

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

- Original issue. Fred Puchlopek

Eric E. Blough 7/19/96

A The MS was revised to:

1. Incorporate NNY LAR 11818 (modified Appendix L for painting of noble metals in the VLS bathtub area).

2. Incorporate SUBMEPP comments (revised SHT note in Appendices C, E, and G).

Fred Puchlopek Eric E. Blough

9/19/97

B The MS was revised to:

1. Incorporate SUBMEPP and NAVSEA comments:

a. Convert MS from Microsoft Word to Arbortext.

b. Incorporate changes to NSTM Chapter 631 dtd 19 December 1996.

c. Add requirements for painting maintenance on SSN21 Class submarines.

d. Update information on rust converters.

e. Remove tinting.

f. Add underwater hull paint systems for 5, 7, and 10 years.

g. Add 100 percent high solids paints for preserving seawater tanks, sail, superstructure, and free flood areas.

h. Change requirements so that non-ferrous and CRES piping in MBTs and CRES snorkel mast surfaces can be left unpainted.

i. Allow the use of the Elcometer 130 SCM 400 salt contamination meter (or equivalent) for performing chloride checks.

j. Update preservation database forms.

k. Add requirement for compliance with NSTM Chapter 631, Chapter 11 QC requirements for critical surfaces.

l. Modify blister acceptance criteria.

m. Modify requirements for performing holiday checks.

n. Update Attachment 12 to reflect latest preservation requirements for SSN688 Class VLS bathtub area.

o. Add requirements for powder coating.

p. Incorporate PHNS UACS 0479-98 (provides modified dry-to-undocking times for copper ablative anti-fouling paints).

Fred Puchlopek Eric E. Blough

1/15/99

B CHG-1 CHG-1 consists of Cover Page, Page ii, Pages 6 through 9 of 107, and Attachments 7 and 8, Pages 24 and 32 of 56. The MS was changed to:

Fred Puchlopek Eric E. Blough

2/19/99

MS NO. 6310-081-015 REV I CHG-2 PAGE ii

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

1. Incorporate TRK UACS 2084A-98 (added NAVSEA INST 9210.36, Steam Plant Cleanliness Control as a reference).

B CHG-2 CHG-2 consists of Cover Page and Page ii. The MS was changed to:

1. Incorporate SUBMEPP comments (extended applicability to MTS626 and 635).

Fred Puchlopek Eric E. Blough

11/19/99

C The MS was revised to:

1. Incorporate SUBMEPP and NAVSEA comments:

a. Added RH requirements for tanks.

b. Expanded chloride contamination testing requirements.

c. Updated rust converter information.

d. Added requirements for use of EURONAVY coatings.

e. Updated bow dome preservation requirements.

f. Updated water jetting requirements.

g. Added and updated preservation database forms.

h. Added information on preservation in way of damping.

i. Updated requirements for inspection of tanks.

j. Added Index of Cognizant Engineers.

k. Added requirements for RBP.

Fred Puchlopek Eric E. Blough

8/18/00

C CHG-1 CHG-1 consists of Cover Page, Page iii, and Attachments 2 through 12 and 14, Pages 3, 7, 11, 15, 20, 23, 35, 41, 46, 52, 56, and 66 of 73. The MS was changed to:

1. Increase the size of the area that can be repaired without QC documentation from 2 square feet to 4 square feet so that URO MRC 004 and URO MRC 005 inspection sites will not require QC documentation for painting.

Fred Puchlopek Scott E. Mercer

12/15/00

D The MS was revised to:

1. Incorporate SUBMEPP and NAVSEA comments:

a. Update index of cognizant engineers and add email addresses.

b. Incorporate NAVSEA Reference Guide Book TMIN SL700-AB-GYD- 010 “Pictorial Guide for Painting Ship’s Interiors”.

c. Revise stripe coating requirements so that stripe coating is required and must be different color than preceding and succeeding coats.

d. Revise dehumidification requirements to specify which readings need to be taken and when the readings need to be taken.

Fred Puchlopek Scott E. Mercer

10/18/02

MS NO. 6310-081-015 REV I CHG-2 PAGE iii

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

e. Add text allowing painting of rubber piece parts of pipe hangers in MBTs, free flood areas, and painted internal tanks.

f. Revise various tables to mandate the use of high solids and require a major departure from specifications if high solids are not used.

g. Correct an error for the induction time for cold weather application of MIL-DTL-24441 paints.

h. Add text allowing application of high solids coatings on MBT flood grates and for specified distances out onto the non-pressure hull.

i. Add requirement to use OXSOL 100 to thin paint on fiberglass mast assemblies.

j. Revise Table 8 by adding additional high solids coatings and making the areas of application more generic.

k. Add high solids coatings to Table 9 for touchup painting.

l. Modify cure times for application of anti-fouling paint on bow domes.

m. Expand the use of high solids coatings to include bilge collecting tanks and sumps and waste oil collecting tanks.

n. Modify Table 15 to specify coating the tanks with system fluid.

o. Modify the requirements for preserving oil tanks by requiring removal of paint systems if coating failure exceeds 1 percent.

p. Add explanation of the intent of a blacklight check.

q. Add SSPC abrasive blast specifications SSPC-AB 2 and SSPC-AB 3.

r. Add industrial blasting in accordance with SSPC-SP 14/NACE No. 8 as an allowed degree of surface preparation.

s. Revise water jetting terminology to reflect the latest SSPC specification SSPC-SP 12/NACE No. 5.

t. Add text which provides information on prioritizing items which should be considered for powder coating.

u. Revise list of approved powder coatings to include Dupont coatings.

v. Revise painting requirements in way of damping tiles by adding acoustic tiles and addressing limits for overspray on damping and acoustic restraining covers.

w. Revise Section 8 to reflect updated Submarine Preservation Database reporting requirements and forms.

x. Revise Attachment 1 to be applicable to all classes of submarines and update inspection requirements.

MS NO. 6310-081-015 REV I CHG-2 PAGE iv

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

y. Revise notes to ensure that the 50 percent relative humidity requirement is complied with when painting with epoxy paints.

z. Revise Table 25 to require replacement of coating systems when the degree of failure exceeds 10 percent.

aa. Revise Attachment 7 to replace International Extent Diagrams with

SSPC VIS 2.

ab. Revise Attachment 8 to clarify the degree of surface preparation required and when mechanical surface preparation can be used in place of abrasive blasting and/or water jetting.

ac. Revise Attachment 12 to require topcoat color to be gray in the VLS area and to delete stripe coating requirements in areas where excess coating thicknesses have caused operational problems.

ad. Add new Attachment 15 for preservation of Thin Line Towed Array equipment in main ballast tanks and stabilizers.

ae. Add text and notes throughout the standard to allow anti-fouling coatings be repaired, touched up, and overcoated with any approved AF system.

af. Add text specifying additional quality assurance (QA) requirements for in service submarines. These new QA requirements provide information on the use of impartial third party inspectors, define mandatory hold points for QA, and invoke oversight requirements.

ag. Revise various sections throughout the MS to specify black as the preferred topcoat color of anti-fouling paint applied below maximum beam.

ah. Add information for the user at the front of the MS.

MS NO. 6310-081-015 REV I CHG-2 PAGE v

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

E The MS was revised to:

1. Incorporate preservation requirements for SSN774 Class.

2. Specify MIL-DTL-24441 Type IV coatings where they are allowed.

3. Provide detailed guidance for taking surface profile readings.

4. Change the name of preservation feedback system from CCIMS to

SPFS.

5. Add new Section 9 and revise Attachments 5 and 7 to provide guidance on requirements to submit departures when deferring preservation work.

6. Incorporate UACS TRK-02-065 to require TYCOMs to keep a log of rust converter use.

7. Allow castor oil to be used as a coating for hydrophone tanks.

8. Incorporate UACS NNS-03-001 to specify painting requirements for piping in RBP recesses.

9. Incorporate LAR TRB-059-B-02 to state that SSBN726 Class missile tube muzzle hatch connecting rod assemblies are to remain unpainted.

10. Add caution that blacklights containing mercury are not allowed to be used shipboard.

11. Add Intergard 143 and Ameron 133/333 high solids paints to Table 8 as approved high solids coatings for seawater environments.

12. Delete mandatory holiday inspection for reserve feedwater tanks.

13. Incorporate UACS NNS-03-037 to delete painting of VLS fairing linkages in Attachment 12.

14. Incorporate NAVSEA ltr ser 07T122/0418 of 20 August 2003 to specify requirements for deferring preservation and clarify URO MRC 003 and MS No. 7650-081-091 inspection requirements.

15. Update requirements for taking environmental readings during periods of planned work stoppage.

16. Add guidance for repair of holidays found by low voltage wet sponge holiday detection.

17. Add list of free flood areas and recesses required to be painted with high solids coatings.

18. Add conductivity check using a conductivity meter as an approved method of checking for chloride contamination.

19. Add requirements for checking chlorides when touchup painting.

20. Update QC requirements for touchup painting areas 4 sq ft or less in size.

Fred Puchlopek Scott E. Mercer

4/16/04

MS NO. 6310-081-015 REV I CHG-2 PAGE vi

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

F The MS was revised to:

1. Incorporate SUBMEPP comments (updated the Index of Cognizant Engineers, changed section 9, Deferring Preservation Work, to delete “Figure 2 of URO MRC 003”, and added new Attachment 17 (which is, except for the numbers, the old Figure 2 of URO MRC 003)).

Fred Puchlopek Scott E. Mercer

8/11/04

G The MS was revised to:

1. Incorporate UACSs PNS-04-135; PNS-03-157; PNS-04-113; PNS-04-

121; PSNS-04-039; NNEWS-05-008; NNS-05-012; TRK-04-075;

EBCORP-05-049; TRK-02-065; PNS-04-134; PSNS-04-037; NNEWS-04-

005; PNS-04-085; NNS-02-002; EBCORP-05-046; EBCORP-05-060;

EBCORP-05-064; and SUBMEPP comments:

a. Update table of non-compliant coatings.

b. Add Hazardous Material Restrictions.

c. Revise and expand Preservation Quality Assurance Requirements.

d. Add table for Quality Control Parameters for preservation in critical coated areas.

e. Add Quality Assurance (QA) forms.

f. Revise the application of Pictorial Guide for Painting Ship’s Interior.

g. Revise and condense Section 2 - Submarine Preservation Interior Painting Requirements.

h. Add vermiculite ore warning for asbestos.

i. Delete Ocean 634/9788 Intumescent paints.

j. Add painting requirements for VRLA Battery Compartments.

k. Rewrite Section 3 Submarine Preservation Exterior Painting Requirements.

l. Combine Table 10 - Exterior Anti-fouling Coating Systems; Table 11 - Underwater Hull Coating Systems; Table 12 - Exterior Paint Systems for SHT (SSN688 and earlier classes); Table 13 - Exterior Paint Systems for SHT/MIP-SHT (SSN21 Class); and Table 14 - Exterior Paint Systems for SHT/MIP-SHT (SSN774 Class) into a single table.

m. Allow data loggers for recording environmental readings.

n. Add Fast CLAD ER and Interbond 998 as approved high solids coatings.

o. Clarify dehumidification readings need to be taken every 4 hours when environmental controls are not used.

p. Revise anti-fouling paint requirements to allow all coatings qualified to

MIL-PRF-24647.

Fred Puchlopek Scott E. Mercer

2/2/06

MS NO. 6310-081-015 REV I CHG-2 PAGE vii

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

q. Add preservation requirements for surfaces covered by fairing compounds and interior surfaces of rudders, planes, and stabilizers.

r. Clarify tack coats are not included when determining cure to immersion times.

s. Add the requirement that powder coatings are not allowed on reserve feedwater and potable water manhole covers.

t. Revise requirements for boiler type manhole covers to leave gasket grooves unpainted.

u. Add the requirement that tank manhole covers are critical coated items.

v. Add preservation requirements for piping in tanks.

w. Add sponge jet blasting as an approved surface preparation process for touchup painting.

x. Add a warning on exposure to cadmium.

y. Revise surface profile verification requirements for touchup painting.

z. Replace the term “manufacturer’s product data sheet” with “ASTM F- 718 form” throughout the standard.

aa. Update section on preservation in way of damping tiles, acoustic tiles, and acoustic baffles.

ab. Revise section on preservation feedback requirements to reflect the use of web based Corrosion Control Information Management System (CCIMS) to replace the Submarine Preservation Feedback System (SPFS).

ac. Revise section on deferring preservation work to provide specific requirements for waivers and deviations.

ad. Change Attachment 17 to be Form 11 and renumber Attachment 16 to be Attachment 17.

ae. Develop new Attachment 16 to provide touchup painting requirements for booted bow domes.

af. Emphasize preservation work on SHT/MIP-SHT requires third party

QA.

ag. Revise reporting requirements to require electronic reporting of preservation work performed via the CCIMS website.

ah. Add requirement to overlap paint 1/2” onto cladded surfaces.

ai. Add warning against excessive use of mechanical tools on SSN21 and SSN774 Classes due to lack of corrosion allowance.

aj. Revise Attachment 5 to specifically invoke the use of Table 25 when assessing condition of coatings and corrective action needed.

MS NO. 6310-081-015 REV I CHG-2 PAGE viii

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

ak. Clarify the requirement to take chloride readings after power tool cleaning and sponge jet blasting.

al. Update Table 25 to incorporate latest distribution terminology from SSPS SP-2 and revised repair action criteria.

am. Add preservation requirements for T-bar Muzzle Hatch Lock Mechanism on SSN719 and SSN720 to Attachment 12.

an. Add preservation requirements for retractable bow planes to Attachment 14.

ao. Revise Attachment 15 to incorporate preservation requirements for thin line equipment on all classes of subs.

ap. Delete SSN683 applicability from the standard.

aq. Modify environmental control requirements to allow forced hot air.

ar. Add requirement to have pump tenders and equipment operators qualified to the Marine Plural Component Applicator Certification Program

(MPCAC).

as. Add exceptions to environmental controls and recording requirements (Step 1.a.(9)(g)).

at. Add statement that QA requirements do not apply to ship’s force painting outside a CNO availability.

au. Exclude bilges from QA/QC requirements for critical coated areas.

av. Add specific surface preparation requirements for SSN688 Class NFO tanks.

aw. Delete requirement to retain Testex tape for OQE purposes.

ax. Add Figures 1 through 8 to Attachment 15 to clarify items that are to be left unpainted.

ay. Replace NSTM Chapter 091 with MS No. 7650-081-091.

Due to the extent of the revision, change bars were not used.

G CHG-1 CHG-1 consists of Cover Page, Page xiii, Pages 10, 120, 121, and 123 through 125 of 172, and Attachment 1, Page 2 of 107. The MS was changed to:

1. Incorporate UACS NAVSEA-08-004 (revised Table 14 coating requirements).

2. Incorporate SUBMEPP comments (updated SUBMEPP’s mailing address).

Fred Puchlopek Scott E. Mercer

4/16/08

G CHG-2 CHG-2 consists of Cover Page, Page xiii, and Attachment 7, Pages 30 and 31 of 107. The MS was changed to:

Fred Puchlopek Scott E. Mercer

5/21/08

MS NO. 6310-081-015 REV I CHG-2 PAGE ix

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

1. Incorporate NAVSEA 07T request at the 774 Class IPT Conference at PNSY 14-15 May 2008 (revised Step 1.a.(2) of Attachment 7 to allow activities to plan for touch-up painting under specified conditions).

G CHG-3 CHG-3 consists of Cover Page, Pages xiii and xiv, Pages 1 through 174 of 174, and Attachments 1 through 18, Pages 1 through 110 of 110. The MS was changed to:

1. Incorporate UACS TRK-08-043 (allowed high solids coatings in 726 Class impulse tanks).

2. Incorporate UACS SUBMEP-08-198 (authorized use of single coat high solids coatings).

Fred Puchlopek Jim Rizas 10/23/08

H The MS was revised to:

1. Incorporate UACSs EBCORP-09-001, PNS-06-083, PSNS-06-049, PNS-08-072, PSNS-08-062, EBCORP-08-024, PNS-06-016, NNEWS-07-

002, NNS-06-029, PNS-08-011, EBCORP-06-027, and PSNS-04-017.

2. Incorporate the following UACSs and move the requirements to NAVSEA Standard Item 009-32: NNS-06-026, TRK-06-029, TRK-08-044, EBCORP-08-012, TRB-07-093, PSNS-06-061, TRK-06-012, EBCORP-

08-025, EBCORP-08-026, PSNS-07-041, and PSNS-06-059.

3. Incorporate NAVSEA Standard Item 009-32 to be the universal requirements document for general shipboard and submarine painting by contractors, intermediate level maintenance activities, and naval shipyards as authorized by NAVSEA ltr Ser 05P23/109 dtd 3 July 2008. In order to accomplish this, the following changes were made:

a. Rewrote Preliminary Sections a.(1)(a) through a.(3)(b) and general painting Section 1.a.(1) to add Standard Item 009-32.

b. Deleted Sections 1.a.(9) through 1.a.(9)(d) (Environmental Controls).

c. Revised Table 7 to list QA Appendices in Standard Item 009-32.

d. Deleted QA Forms 1 through 8.

e. Deleted Table 8 (Paint Systems on Interior Surfaces).

f. Deleted Table 10 (High Solids Coatings Approved for Submarine Use).

g. Deleted Table 11 (Exterior Coating Systems).

h. Deleted Section 3.b.(8) and Table 13 (Bow Dome Coatings).

i. Deleted Table 14 (Submarine Tank Coatings).

j. Deleted Sections 5.d. through 5.e.(10) (Cleaning, SSPC Surface Prep Methods, and Waterjetting).

k. Deleted Table 17 (Abrasive Blast Media).

l. Deleted Table 18 (Specifications for Blast Cleaning).

Fred Puchlopek Jim Rizas 6/1/09

MS NO. 6310-081-015 REV I CHG-2 PAGE x

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

m. Deleted Section 5.f. (Check for Chloride Contamination).

n. Deleted Section 5.g. (Surface Profile Verification).

o. Deleted Section 5.h. (Cure Times for Coating Systems).

p. Added Standard Item 009-32 throughout the MS to reference the coatings and preservation requirements that were deleted from the MS and moved to the Standard Item.

q. Deleted Section 4.b.(4) (Potable Water Tank Preservation). Requirement moved to Standard Item 009-32.

r. Deleted Section 4.b.(6) (Holiday Detection in Potable Water Tanks).

Requirement moved to Standard Item 009-32.

s. Revised QC notes in all attachments to refer to Standard Item 009-32.

4. Incorporate the following changes due to user input, NAVSEA, and SUBMEPP comments:

a. Deleted NR-1 from cover sheet.

b. Revised Table 1 to reflect changes to NSTM Chapter 631 and deleted CCIMS as a reference.

c. Updated references to paragraphs in NSTM Chapter 631.

d. Rewrote Section 1.a.(11) (formerly 1.a.(9)(e)) to provide guidance on environmental controls if DH is disestablished and during periods of work stoppage.

e. Rewrote Section 1.a.(16) (formerly 1.a.(12)) to update guidance on local, state, and federal environmental regulations.

f. Updated Table 2 to delete cancelled paint specifications.

g. Updated Table 3 to delete cancelled paint specifications and added new paint specifications.

h. Changed NAVSEA 07T12 to PMS 392T12 to reflect new NAVSEA code designation.

i. Updated list of unpainted items in Section 1.d.

j. Revised Table 5 to delete flash point and pot life from list of conformance tests and revised viscosity test to delete coating component test.

k. Updated Table 7 to delete environmental checks during surface preparation.

l. Revised Section 2.a.(7)(a)1 to require exhaust ventilation for interior painting during underway operations only.

m. Changed Devflex 601 to Amercoat 601A throughout the MS.

MS NO. 6310-081-015 REV I CHG-2 PAGE xi

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

n. Added new Section 2.a.(8)(h) to address photo luminescent marking tape replacement.

o. Revised Section 4.a.(5) to provide guidance on acceptable surface preparation methods for CRES piping in tanks.

p. Revised Section 4.a.(7) to require stripe coating only when using non-edge retentive coatings.

q. Added requirement throughout MS to maintain system cleanliness when working on flasks.

r. Added lube oil stowage, sumps, settling, and holding tanks to Table 10 (formerly Table 15).

s. Added NSTM Chapter 074 Volume 3 Gas Free Engineering for safety precautions when working in oil tanks.

t. Updated Table 11 (formerly Table 19) to add new powder coating and deleted duplicates.

u. Updated instructions for completing Submarine Preservation Records.

v. Revised Section 9 by adding the NAVSEA Departure from Specifications (DFS) Decision Tree and adding MS No. 7650-081-091 for unscheduled visual inspection preservation requirements.

w. Added SSN774 Class SHT Manual to Table 13 (formerly Table 21).

x. Deleted vinyl anti-fouling paint from the MS.

y. Added SSN21 and SSN774 Class potable water tanks to Note 6 of Table 17 (formerly Table 23).

z. Revised Attachment 8 to allow brush or roller application of UHS paint in free flood areas less than 75 sq-ft and in certain 726 Class tanks.

aa. Revised Attachment 15 to provide updated guidance on preservation of TLTA equipment. Deleted Figures 1 through 8.

ab. Revised Section 1.a.(1) of Attachment 16 to state that the intent is to touchup anti-fouling paint on booted bow domes.

ac. Renumbered sections, tables, and figures as needed.

MS NO. 6310-081-015 REV I CHG-2 PAGE xii

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

H CHG-1 CHG-1 consists of Cover Page, Page xviii, Pages 1 through 103 of 103, and Attachments 2 through 16, Pages 3, 6, 7, 10, 11, 13 through 15, 17, 18, 20 through 22, 25 through 32, 35, 37, 38, 40, 43, 45 through 49, 52 through 54, 57 through 65, 68 through 72, 76 through 79, and 93 of 96. The MS was changed to:

1. Incorporate UACS SUBMEP-09-185 (added Table 9 for preservation of Retractable Bow Plane (RBP) recess, VLS bathtub, and universal modular mast and added AN/BQN-13 and AN/BQS-15/AN-BSY-1 recesses to Table 17 Note 6 for SSN688 Class).

Fred Puchlopek Jim Rizas 9/18/09

H CHG-2 CHG-2 consists of Cover Page, Pages xviii through xx, Pages 1 through 105 of 105, and Attachments 1 through 18, Pages 1 through 100 of 100.

The MS was changed to:

1. Incorporate TMR A067-09 (added safety note).

2. Incorporate UACSs SUBMEP-09-246; SUBMEP-10-137; SUBMEP-10- 208; PNS-10-103; NEW88MS-068; SUBMEP-11-085; and SUBMEPP comments:

a. Added Attachment 17 to the List of Attachments.

b. Corrected index of Cognizant Engineers.

c. Added paragraph a.(2)(d) for clarification of up to date painting requirements.

d. Added SSN774 Class manual to Table 1.

e. Updated Table 2 in accordance with latest change to the DDGOS.

f. Replaced NAVSEA approved ASTM F-718 with NAVSEA-reviewed ASTM F-718 throughout the document.

g. Correction to paragraph 1.d.(1) for correct paragraph reference for Chapter 631.

h. Added 1.d(1)(v) Main shaft hull insert bearing lands and clad surfaces to the list of unpainted surfaces.

i. Added TRFKB request to paragraph 1.j.(2) to identify that non critical coated areas need QA/QC requirements when SSPC-SP-10 is being accomplished.

j. Reworded paragraph 3.a.(4).

k. Updated Table 9, Table 9 notes, and Attachment 14 requirements for RBP recess and components.

l. Removed paragraph 3.b.(8)(a) (no longer needed).

m. Updated section 4 to add rafted tanks, MS No. 7650-081-091 guidelines, paragraph 4.a.(10) for chemical analysis for mercury contamination, 4.a.(11) for preservation in way of lead bins, and NFO requirements for SSN774-777.

Anita C. Adams Jim Rizas 4/27/11

MS NO. 6310-081-015 REV I CHG-2 PAGE xiii

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

n. Updated Attachment 9 to include NFO tank blast requirements for

SSN774-777.

o. Updated Attachment 12, replaced “zinc” with “sacrificial anode”.

p. Updated Attachment 14 for preservation requirements for RBP recess and components.

q. Added Attachment 17 and wording to section 3 for preservation of shaft tube hull inserts.

r. Added NAVSEA ltrs for mercury contamination for Seawolf and SSN688 Class hulls to the NAVSEA Correspondence List.

H CHG-3 CHG-3 consists of Cover Page, Page xx, Pages 3 through 6, 10, 11, 27 through 30, 48, and 49 of 105, and Attachments 1 through 18, Pages 1 through 102 of 102. The MS was changed to:

1. Incorporate UACS NAVSEA-11-005 (added MS No. 6310-081-019 to list of Reference Documents, revised interior painting requirements, and added Note 1 to Attachment 6).

2. Incorporate UACS SUBMEP-11-144 (revised Figures 2 through 5 of Attachment 17).

3. Incorporate UACS PNS-11-056 (revised Attachment 15).

4. Incorporate UACS MTSSY-11-002 (revised Attachment 1).

5. Incorporate UACS SUBMEP-12-055 (added caution and revised Attachments 2, 3, 5, 7, 8, and 15).

6. Incorporate DDGOS ACN M13-11 changes.

7. Incorporate SUBMEPP action items identified in NAVSEA ltr Ser 392T127/038 dtd 18 Jan 2012.

Anita C. Adams Jim Rizas 4/24/12

H CHG-4 CHG-4 consists of Cover Page, Page xxi, Pages 1 through 106 of 106, and Attachments 2 through 15, Pages 3, 6, 7, 10, 11, 14, 15, 17, 18, 20, 21, 23, 26, 27, 30, 37, 39, 40, 42, 45, 47, 50, 51, 55, 56, 59 through 61, 66 through 68, 71 through 74, 79 through 81, and 95 of 102. The MS was changed to:

1. Incorporate UACS PNS-12-062 (added Method 7473 as an acceptable method for testing for mercury in solids).

2. Incorporate UACS SUBMEP-12-095 (added caution alerting users to MS policy and applicability limitations MS No. 7650-081-010).

Martha M. Bowman Jim Rizas 6/8/12

H CHG-5 CHG-5 consists of Cover Page, Page xxi, Page 70 of 106, and Attachment 7, Page 29 of 102. The MS was changed to:

1. Incorporate UACS SUBMEP-12-151 (updated NAVSEA address).

Martha M. Bowman Jim Rizas 8/2/12

H CHG-6 CHG-6 consists of Cover Page, Page xxi, and Attachment 12, Page 63 of

102. The MS was changed to:

Martha M. Bowman Jim Rizas 12/19/12

MS NO. 6310-081-015 REV I CHG-2 PAGE xiv

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

1. Incorporate UACS PNS-12-067 (revised preservation system of Attachment 12).

H CHG-7 CHG-7 consists of Cover Page, Page xxi, and Attachment 12, Pages 62 through 65 of 102. The MS was changed to:

1. Incorporate UACSs PNS-12-155 and NSWCCD-12-007 (revised Attachment 12).

Martha M. Bowman Jim Rizas 1/18/13

I The MS was revised to:

1. Incorporate UACS SUBMEP-12-245 (incorporated SUBMEPP and NAVSEA comments:

a. Added VHB tape lead bin rubber usage (Step 4.a).

b. Added PVC ICCP mounting hardware and components to unpainted surfaces.

c. Removed reference document NAVSEA INST 9210.36 Steam Plant Cleanliness Control.

d. Updated compliant paints in Table 2 in accordance with NSTM Chapter 631.

e. Removed receipt inspection testing requirement for characteristics provided on manufacturer’s certificate of compliance or conformance data forms.

f. Updated web address for the SMCL.

g. Removed outdated prohibition on underwater hull cleaning of SHT boats without NAVSEA approval.

h. Added specification for use of glasses with blacklights to Section 5.

i. Added visual water break test in accordance with SI 009-32.

j. Incorporated NAVSEA ltr 9110 Ser PMS 392TE/012 dtd 29 Jan 2013, clarified Mercury testing in specified tanks, Step 4.a.

k. Incorporated UHP water jetting and SSPC-SP 10 abrasive blast surface preparation for coating preservation in SSN688 Class and SSN774 Class NFO tanks.

l. Removed underwater hull cleaning reporting requirements from Attachment 1.

m. Added Attachment 18 to allow for partial abrasive blasting as a result of CWP 356 as approved by NAVSEA technical warrant holder.

n. Added item 32 to NAVSEA correspondence list in order to expand single coat usage to sanitary, bilge, and drain collecting tanks.

2. Incorporate UACS SUBMEP-13-051 (added Houghton PR1192 fluid for tank preservation).

Martha M. Bowman Jim Rizas 7/25/13

MS NO. 6310-081-015 REV I CHG-2 PAGE xv

REVISIONS/CHANGES

REV DESCRIPTION APPROVAL & DATE

3. Incorporate UACS SUBMEP-13-072 (excluded propulsor from MS scope).

I CHG-1 The MS was changed to:

1. Incorporate UACS PSNS-13-170 (updated rubber pipe hanger preservation note to reflect new guidance in SI 009-32).

2. Incorporate UACS SUBMEP-13-470 (updated section 9 guidance to reflect when DFSs have to go to NAVSEA based on Submarine Decision Matrix; removed reference to SSPC-SP1Z and replaced with SSPC/NACE WJ2; updated NFO tank preservation guidance to specify height for SSBN/ SSGN and coating system to install; corrected allowable salt concentration from M to U; added metallic structures requiring grounding to list of items that must be left unpainted (new Step 1.d.(1)(y) and NOTE 26 of Attachment 8)).

3. Incorporate SUBMEPP comments (updated format to latest XML technology in preparation of future HTML output).

Martha M. Bowman Cynthia L. Waters

2/24/14

I CHG-2 The MS was changed to:

1. Incorporate UACS PNS-14-014 (defined time frame of tank liquid sample).

2. Incorporate SUBMEPP comments (clarified NFO tank cleaning requirements).

Martha M. Bowman Cynthia L. Waters

6/19/14

MS NO. 6310-081-015 REV I CHG-2 Page 1 of 105

MAINTENANCE STANDARD

Information to the User

The Submarine Preservation Maintenance Standard combines technical information normally found in government technical manuals and detailed maintenance processes for coatings into a single document dedicated to the proper application and maintenance of coating systems on US Navy submarines. This maintenance standard was developed in 1996 to consolidate submarine preservation requirements previously contained in many different documents (maintenance standards, IMMP MRCs, technical manuals, drawings, paint schedules, letters, and naval messages) into a single document that could be easily revised to keep pace with changing preservation requirements.

The 2 major parts to this maintenance standard are: 1) systems technical information for selecting and applying coatings and 2) attachments containing maintenance processes for repairing or replacing coatings. A table of contents, located in the front of the standard, provides a detailed breakdown of the various sections of the MS.

Technical information provided on pages 7 through 99 is similar to that typically found in a Naval Ships

Technical Manual (NSTM) chapter. Users should look in this part of the MS if they are trying to determine the type of coatings applied in various areas of the sub, required coating thickness, explanation of various cleaning and surface preparation requirements, specific quality assurance inspections, and feedback requirements. The technical information sections are arranged as follows:

• Preliminary Section a; pages 7 to 11 - General information - includes scope, purpose, explanation of document hierarchy, and list of references.

• Section 1; pages 11 to 41 - General painting for submarines - includes information on cosmetic painting, dry film thickness limits, stripe coating, relative humidity requirements, information on safety, workmanship, list of approved coatings, quality assurance requirements, types of maintenance, and types of availabilities.

• Section 2; pages 42 to 47 - Interior painting - includes interior coatings and cold weather touchup painting of bilges and tanks.

• Section 3; pages 47 to 57 - Exterior painting - includes exterior anti-corrosive and anti-fouling coatings applied to exterior hull surfaces, non-skid areas, SHT, and bow domes.

• Section 4; pages 57 to 64 - Tank painting - includes anti-fouling coatings in MBTs, coating requirements for high pressure air flasks and piping in MBTs, coatings in oil tanks, and coatings for manhole covers.

• Section 5; pages 64 to 66 - Submarine preservation maintenance processes - includes information on sponge jet blasting using the RASP system. Also provides information on the use of Attachment 1 through Attachment 16 to accomplish preservation on submarines.

• Section 6; pages 66 to 69 - Powder coating - provides table of NAVSEA-approved powder coatings and the requirements for applying them.

• Section 7; pages 70 to 71 - Preservation in way of damping and acoustic tiles - provides requirements and limitations for coatings applied to damping and acoustic tiles.

• Section 8; pages 71 to 83 - Preservation feedback - includes information on entering data into the Corrosion Control Information Management System (CCIMS), copies of blank feedback forms, and instructions for completing the forms.

• Section 9; pages 84 to 99 - Resolving Preservation Out-of-Specification Conditions - provides the Submarine Preservation Decision Matrix and requirements for submitting waivers and deviations when preservation work is out-of-specification.

MS NO. 6310-081-015 REV I CHG-2 Page 2 of 105

Attachments contained in this MS provide the user with the process to be used to repair or replace a coating system in a particular area on a submarine. Table 16 (Pages 99 to 102) summarizes the attachments in the maintenance standard. Users typically are instructed by the work package or maintenance plan to use a specific attachment to accomplish maintenance. Alternately, if the user knows the area of the sub and the type of maintenance to be performed, they can choose an attachment from Table 16. Each attachment contains all the steps involved in the repair or replacement of a coating system. This typically includes cleaning, surface preparation, inspection, coating application, quality assurance inspections, and reporting requirements. When performing the work specified in any of the attachments, the user will need to refer to the technical information located on pages 7 through 99 in order to properly clean and prepare the surface for painting, accomplish required quality assurance inspections, select the proper coating, determine coating thicknesses, and report the work accomplished using the Corrosion Control Information Management System.

MS NO. 6310-081-015 REV I CHG-2 Page 3 of 105

Table of Contents List of Attachments - Maintenance Processes 4 List of Tables 5

List of Forms 6 Index of Cognizant Engineers 6

Preliminary 7

a. General Information 7 a.(1) Purpose 7 a.(2) Scope 7 a.(3) General 7 a.(4) Reference Documents 8

1. Submarine Preservation General Painting 11

1.a. General Painting 11

1.b. Safety 22

1.c. Workmanship 23

1.d. Unpainted Surfaces 24

1.e. Types of Preservation Maintenance 25

1.e.(1) Scheduled Preservation Upkeep Coordinated Effort (SPRUCE) 25

1.e.(2) Touchup Painting 26

1.e.(3) Clean and Repair/Restore Preservation 26

1.e.(4) Prepare and Represerve 26

1.f. Maintenance Requirements During the Operating Cycle (Underway Painting) 26

1.f.(2) Rust Converters 27

1.g. Maintenance Requirements During the Operating Cycle (SPRUCE Upkeeps) 29

1.h. Maintenance During Short Availabilities (SRAs, RAVs, TAVs, ERPs, etc.) 29

1.i. Maintenance During Major Industrial Availabilities (DMPs, EOHs, RFs) 29

1.j. Preservation Quality Assurance (QA) Requirements for In Service Submarines 29

1.k. Quality Assurance Forms 42

2. Submarine Preservation Interior Painting 43

2.a. Painting Interior Surfaces 43

2.a.(7) Restrictions 43

2.a.(8) Interior Coatings 44

2.a.(9) Cold Weather Touchup Painting 46

MS NO. 6310-081-015 REV I CHG-2 Page 4 of 105

Table of Contents 2.a.(10) Cold Weather Touchup Paints for Tanks and Bilges 46

2.a.(11) Cold Weather Application Requirements for MIL-DTL-24441 Paint System 47

3. Submarine Preservation Exterior Painting 48

3.a. Painting Exterior Surfaces 48

3.b. Exterior Coatings 49

3.b.(2) Exterior Anti-corrosive Coatings 49

3.b.(3) Exterior Anti-fouling Coatings 51

3.b.(4) Exterior Non-Skid Coatings 52

3.b.(5) Exterior Special Hull Treatment (SHT) Coatings 52

3.b.(8) Painting of Submarine Bow Sonar Domes 59

4. Submarine Preservation Tank Painting 59

4.a. Painting in Tanks 59

4.b. Tank Coatings 62

5. Submarine Preservation Maintenance Processes 66 5.e. Sponge Jet Blasting 67

6. Submarine Preservation Powder Coating 68

7. Submarine Preservation in Way of Damping Tiles, Acoustic Tiles, and Acoustic Baffles 72

8. Submarine Preservation Feedback 73

9. Resolving Preservation Out-of-Specification Conditions 86

9.a. Preservation Departures from Specifications Process Decision Tree 86

9.b. Required Content for Departures from Specifications (DFS) 86

9.c. Major Departures from Specifications 86

9.d. URO MRC 003 Preservation Requirements 86

9.e. Unscheduled Visual Inspection Preservation Requirements 87

9.f. Requirements for Preservation in Process Deviations 87

List of Attachments - Maintenance Processes Attachment 1 Underwater Inspection and Cleaning of Anti-fouling Paint 1

Attachment 2 Inspect, Clean, and Touchup Anti-fouling Paint on Steel 2

Attachment 3 Repair or Replace Anti-fouling Paint on Steel 5

Attachment 4 Repair Anti-fouling Paint on GRP Bow Domes 9

Attachment 5 Touchup Anti-corrosive Paint on Exterior Surfaces and in Tanks 13

MS NO. 6310-081-015 REV I CHG-2 Page 5 of 105

Table of Contents Attachment 6 Touchup Anti-corrosive Paint on Interior Surfaces and Bilges Using Solvent Based Paint Systems

Attachment 7 Clean and Repair/Restore Preservation 24

Attachment 8 Prepare and Represerve 35

Attachment 9 Clean and Repair/Restore Preservation in Oil Tanks 41

Attachment 10 Replace Anti-corrosive and Anti-fouling Paints on Bow Domes 47

Attachment 11 Replace Anti-fouling and Anti-corrosive Paint on Booted Bow Domes 52

Attachment 12 Prepare/Represerve VLS Bathtub Area Preservation System 55

Attachment 13 Touchup Bilges Using High Solids Coatings 61

Attachment 14 Prepare/Represerve Retractable Bow Plane (RBP) Recess and Components within Recess

Attachment 15 Prepare/Represerve Thin Line Towed Array Components in Main Ballast Tanks, Free Flood Areas, and Horizontal Stabilizer

Attachment 16 Touchup Anti-fouling and Anti-corrosive Paint on Booted Bow Domes 82

Attachment 17 Preservation of Shaft Tube Inserts 85 Attachment 18 Partial Abrasive Blast Cleaning 89

Attachment 19 NAVSEA Correspondence List 95

List of Tables Table 1 Reference Documents 8 Table 2 Non-Compliant Paints and Their Compliant Alternatives 15

Table 3 Additional Compliant Materials Approved for Use on Submarines (Not listed in Table 2) 20

Table 4 Rust Converter Paints Approved for Underway Use 28

Table 5 Receipt Inspection Conformance Tests for MIL-DTL-24441, MIL-PRF-23236, MIL-PRF- 24647 (AC Coating only), and MIL-DTL-24631 (SHT Topcoats) Coatings

Table 6 Receipt Inspection Conformance Tests for Anti-fouling Coatings 32

Table 7 Quality Control Parameters for Preservation Process in Critical Coat Areas 34

Table 8 Cold Cure/Surface Tolerant Paint Systems 48

Table 9 SHT Maintenance Instruction Documents 50 Table 10 Exterior Coating Systems 54

Table 11 Exterior Touchup Paints 59

Table 12 Preservatives for Oil Tanks 65 Table 13 Powder Coatings Approved for Submarine Use 70

Table 14 Preservation Data Forms 75

Table 15 Submarine Preservation Departures from Specifications Process Decision Matrix 88

MS NO. 6310-081-015 REV I CHG-2 Page 6 of 105

Table of Contents Table 16 Summary of Maintenance Processes 101

Table 17 Surface Roughness, Grooming, and Paint Application Requirements Att 4, Pg 11

Table 18 Unacceptable Blister Size and Density Att 5, Pg 15

Table 19 Unacceptable Blister Size and Density Att 7, Pg 27

Table 20 Preservation Assessment Criteria Att 7, Pg 28

Table 21 Unacceptable Blister Size and Density Att 9, Pg 42

Table 22 Preservatives for Oil Tanks Att 9, Pg 45

Table 23 Surface Roughness, Grooming, and Paint Application Requirements Att 10, Pg 50

Table 24 EURONAVY ES301K and ES301L Coating Systems for Submarine Bilges Att 13, Pg 63

List of Forms Form 1 Submarine Tanks/Voids/Free Floods, Sail, Superstructure, and Interior Miscellaneous Inspection Worksheet

Form 2 Submarine Exterior Hull Inspection Worksheet 84

Form 3 SSBN726 Class Deficiency Feedback Form 100

Index of Cognizant Engineers

Criteria for: Cognizant Engineer

Non-Pressure Hull Bow Domes Superstructure, Fairwater

Mike Durkin, Code 1873MD

(207) 438-6075 email: michael.e.durkin@navy.mil

Pressure Hull Interior and Exterior Preservation Damping and Acoustic Tiles

Martha Bowman, Code 1873MB

(207) 438-6106 email: martha.bowman@navy.mil

Tanks (Interior and Exterior) Patrick Blough, Code 1873PB

(207) 438-6391 email: patrick.blough@navy.mil

Corrosion Control Information Management System (CCIMS) Feedback and CCIMS request for validation must be submitted to Martha Bowman.

MS NO. 6310-081-015 REV I CHG-2 Page 7 of 105

Preliminary

CAUTION: Familiarity with the Maintenance Standard (MS) Program policy and applicability limitations identified in MS No. 7650-081-010 is required prior to use of this MS.

a. General Information a.(1) Purpose a.(1)(a) The purpose of this NAVSEA-approved MS is to provide guidance in complying with submarine preservation requirements mandated by NAVSEA Standard Item (SI) 009-32. SI 009-32 has been designated as the single or “universal” requirements document for general shipboard and submarine painting by contractors, intermediate level maintenance activities, and Naval Shipyards. All requirements for selecting and applying coatings on submarines, including surface preparation, environmental controls, cleanliness, coating system selection and film thicknesses, and quality assurance (QA) requirements are now provided in SI 009-32. This maintenance standard contains submarine specific process information and guidance on preserving damping tiles, applying powder coatings, feedback reporting using CCIMS, and maintaining preservation systems to support URO MRC 003 periodicities. Attachments retained in this MS provide detailed guidance on assessing coating systems and also provide detailed procedures for preserving areas and surfaces that are unique to submarines such as bow domes, VLS free flood bathtub area, retractable bow plane recesses, and thin line tow array equipment. This MS is to be used in conjunction with SI 009-32 to provide current information on preservation requirements for submarines.

a.(2) Scope a.(2)(a) This MS provides guidance for Intermediate Maintenance Activities (IMAs), Naval Shipyards, Regional Maintenance Centers (RMCs), and Navy Contractors to be used in conjunction with SI 009-32 for maintaining, repairing, and replacing preservation systems on non-nuclear, non-SOC components and spaces of U.S. Navy submarines. The intent is to use this document when performing Intermediate (I) and Depot (D) level maintenance on preservation systems of submarines in service. The guidance specified in this MS are not intended for use by ship’s force.

Requirements for accomplishing Scheduled Preservation Upkeep Coordinated Efforts (SPRUCE) are included for informational purposes to assist the Type Commanders, IMAs, and ship’s force personnel in preparing for and accomplishing internal preservation on operational submarines during the operating cycle.

a.(2)(b) Submarine specific items that are not addressed in SI 009-32 must be preserved in accordance with the requirements of this MS.

a.(2)(c) Items not specifically painted by this MS are to be preserved as required by the MS for that component/item. The procedures, methods, and restrictions in this MS apply only when specifically referenced or invoked by the standard that specifies the coating system and maintenance requirement for the component/item. Propulsor preservation is outside the scope of this MS and must be in accordance with NAVSEA S9245-AZ-TSM-010, Submarine Ducted Propulsor Installation, Inspection, Repair, Maintenance, and Certification.

a.(2)(d) The ship’s paint schedule may not reflect current painting requirements. This MS and NAVSEA Standard Item 009-32 Table 6 for exterior surfaces and Standard Item 009-32 Table 8 for tanks should first be consulted for the most up to date painting requirements.

a.(3) General a.(3)(a) This MS is to be used with Standard Item 009-32 to perform repairs and maintenance of existing paint and preservation systems used on submarine structures, equipment, and materials. This

PROCEDURE

MS NO. 6310-081-015 REV I CHG-2 Page 8 of 105 standard is not intended to be used during new construction or when applying original coating systems to new equipment.

a.(3)(b) This MS complies with requirements contained in Standard Item 009-32 and NSTM Chapter 631, except where deviations are specifically approved by NAVSEA. In instances where the guidance specified in this MS conflict with requirements specified in Standard Item 009-32, the criteria of Standard Item 009-32 governs. In instances where the guidance specified in this MS conflict with the requirements of other standards (including but not limited to NSTM, DDGOS, MRCs, MSs, and Individual Ship’s Paint Schedules), the criteria of this standard must govern.

a.(3)(c) The latest revision of NAVSEA Standard Item 009-32 approved at the start of planning must be used through availability completion. Use of a later revision requires NAVSEA PMS392T12 approval.

NOTE 1: This document supplements and modifies NSTM Chapter 631 and is intended to implement the requirements of Standard Item 009-32 and NSTM Chapter 631 while resolving and clarifying any conflicts. This standard will also be changed in a timely manner when directed by NAVSEA, whereas changes to NSTM chapters often involve a lengthy process.

a.(3)(d) NSTM Chapter 997 requires that paint systems applied to ships by I and D level activities be documented on docking reports. The intent is to provide a record of coatings on a ship when it leaves an availability. This information will be entered in the CCIMS per Section 8 of this MS.

The resulting historical database can be used by activities to track coatings applied over the life of the ship and to plan future maintenance. Forward a copy of all docking reports to:

Director SUBMEPPActivity PO Box 2500 Portsmouth Naval Shipyard Portsmouth, NH 03804-2500 Attention: Code 1844 a.(3)(e) All requested changes to this MS must be submitted to SUBMEPP using the User Activity Comment Sheet (UACS) located on the MSs CD distributed by SUBMEPP. NAVSEA (SEA 07T) has technical authority over and must approve any changes to this standard.

a.(4) Reference Documents a.(4)(a) Table 1 lists documents used/referred to in this standard. The documents are listed here in 1 consolidated location for the convenience of the user. Refer to NAVSEA Correspondence List of this standard for a list of NAVSEA correspondence (letters, LARs, and messages) used in this standard.

NOTE 2: References in Table 1 are listed by type of document (i.e., NSTM, SSPC, NACE, etc.).

Table 1. Reference Documents

Document Number Title NAVSEA S9086-VD-STM-010 NSTM Chapter 631, Preservation of Ships in Service -

General NAVSEA S9086-CH-STM-030/CH-074 NSTM Chapter 074 Volume 3, Gas Free Engineering

NAVSEA S9086-CQ-STM-010/CH-081 NSTM Chapter 081, Waterborne Underwater Hull Cleaning of Navy Ships

PROCEDURE (Cont’d)

MS NO. 6310-081-015 REV I CHG-2 Page 9 of 105

Table 1. Reference Documents (Cont'd)

Document Number Title NAVSEA S9086-S4-STM-010/CH-556 NSTM Chapter 556, Hydraulic Equipment, Power

Transmission and Control NAVSEA S9086-VG-STM-010/CH-634 NSTM Chapter 634, Deck Coverings

NAVSEA S9086-WK-STM-000/CH-670 NSTM Chapter 670, Stowage Handling and Disposal of Hazardous General Use Consumables

NAVSEA S9510-AB-ATM-010/(U) Submarine Atmosphere Control Manual

NAVSEA 0989-064-3000 Cleanliness Requirements for Nuclear Propulsion Plant Maintenance by Forces Afloat

NAVSEA SE 110-BK-MMO-010 Procedures for Inspection, Repair, and Painting of Fiberglass Mast Assemblies

NAVSEA SE300AY-MMA-010/SSBN726CL Trident GRP Bow Sonar Dome Handbook NAVSEA S9165-AC-HBK-010 Submarine Sonar Dome Handbook (for SSN688 Class)

NAVSEA SE300-AZ-MMA-010 SSN21 Class Sonar Bow Dome NAVSEA SE300-AE-MMA-010 SSN774 Class Bow Sonar Dome and Chin Array

NAVSEA S6360-AD-HBK-010 Special Hull Treatment (SHT) Maintenance and Repair (for SSN688 Class and earlier)

NAVSEA S6360-AN-MMA-010/SHT Submarine Mold-In-Place Special Hull Treatment Maintenance and Repair Manual (for SSN21 Class)

NAVSEA S6360-AV-MMA-010/SHT Submarine Mold-In-Place Special Hull Treatment Maintenance and Repair Manual (for SSN774 Class)

NAVSEA Drawing 690-7383660 Special Hull Treatment Installation (SSN774 Class)

URO MRC 003 Hull Structural Survey

DOD INST 6050.5 The DOD Hazardous Material Information System

(HMIS)

OPNAV INST 5100.19 Vols. I and III, Navy Occupational Safety and Health (NAVOSH) Program Manual for Forces Afloat

OPNAV INST 5100.23 Navy Occupational Safety and Health (NAVOSH) Program Manual

COMUSFLTFORCOMINST 4790.3 SPRUCE Requirements, Volume VI, Chapter 27 of the Joint Fleet Maintenance Manual

COMSUBPAC TECH NOTE 02-93 Submarine Preservation Equipment

OSHA Regulation Title 29 CFR 1910.146 Permit - Required Confined Spaces for General Industry

ASTM D 714 American Society for Testing and Materials No.

D 714, Standard Method of Evaluating Degree of Blistering of Paints

MS NO. 6310-081-015 REV I CHG-2 Page 10 of 105

Table 1. Reference Documents (Cont'd)

Document Number Title ANSI B46.1 Surface Roughness, Waviness and Lay

NSRP 0412 SSPC Surface Preparation and Coating Handbook dtd June 1994

FED STD 595 Colors Used in Government Procurement MIL-S-851D(3) Steel Grit, Shot, and Cut Wire Shot; and Iron Grit and

Shot-Blast Cleaning and Peening

MIL-STD-2138 Metal Sprayed Coatings for Corrosion Protection Aboard Naval Ships

MIL-D-16791 Detergents, General Purpose (Liquid, Nonionic)

MIL-A-22262 Abrasive Blasting Media Ship Hull Blast Cleaning

MS No. 6310-081-019 Submarine Preservation of SOC Chambers and Trunks MS No. 7650-081-091 Submarine Hull Inspection

SSPC-AB 2 Cleanliness of Recycled Ferrous Metallic Abrasives

SSPC-AB 3 New Manufactured or Remanufactured Steel Abrasives 1SSPC-SP 1 Solvent Cleaning 1SSPC-SP 2 Hand Tool Cleaning 1SSPC-SP 3 Power Tool Cleaning 2SSPC-SP 5/NACE #1 White Metal Blast Cleaning 2SSPC-SP 10/NACE #2 Near-White Blast…