08 71 00.pdf

P-303 Marine Corps Reserve Center W.O. No. 1624797 Camp Fretterd, Reisterstown, MD AMMENDMENT 3

SECTION 08 71 00

DOOR HARDWARE

02/16

PART 1 GENERAL

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

ASTM INTERNATIONAL (ASTM)

ASTM E283 (2004; R 2012) Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen

BUILDERS HARDWARE MANUFACTURERS ASSOCIATION (BHMA)

ANSI/BHMA A156.1 (2016) Butts and Hinges

ANSI/BHMA A156.2 (2017) Bored and Preassembled Locks and Latches

ANSI/BHMA A156.3 (2014) Exit Devices

ANSI/BHMA A156.4 (2013) Door Controls - Closers

ANSI/BHMA A156.5 (2014) Cylinder and Input Devices for Locks

ANSI/BHMA A156.6 (2015) Architectural Door Trim

ANSI/BHMA A156.7 (2016) Template Hinge Dimensions

ANSI/BHMA A156.8 (2015) Door Controls - Overhead Stops and Holders

ANSI/BHMA A156.13 (2017) Mortise Locks & Latches Series 1000

ANSI/BHMA A156.16 (2018) Auxiliary Hardware

ANSI/BHMA A156.18 (2016) Materials and Finishes

ANSI/BHMA A156.21 (2014) Thresholds

ANSI/BHMA A156.22 (2017) Door Gasketing and Edge Seal Systems

ANSI/BHMA A156.23 (2010) Electromagnetic Locks

ANSI/BHMA A156.25 (2013) Electrified Locking Devices

ANSI/BHMA A156.26 (2012) Continuous Hinges

ANSI/BHMA A156.31 (2013) Electric Strikes and Frame Mounted

SECTION 08 71 00 Page 1

Actuators

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

NFPA 70 (2017; ERTA 1-2 2017; TIA 17-1; TIA 17-2;

TIA 17-3; TIA 17-4; TIA 17-5; TIA 17-6;

TIA 17-7; TIA 17-8; TIA 17-9; TIA 17-10;

TIA 17-11; TIA 17-12; TIA 17-13; TIA

17-14; TIA 17-15; TIA 17-16; TIA 17-17 )

National Electrical Code

NFPA 72 (2019; TIA 19-1; ERTA 2019) National Fire Alarm and Signaling Code

NFPA 80 (2016; TIA 16-1) Standard for Fire Doors and Other Opening Protectives

NFPA 101 (2018; TIA 18-1; TIA 18-2; TIA 18-3) Life Safety Code

NFPA 252 (2017) Standard Methods of Fire Tests of Door Assemblies

STEEL DOOR INSTITUTE (SDI/DOOR)

SDI/DOOR A250.8 (2003; R2008) Recommended Specifications for Standard Steel Doors and Frames

U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)

36 CFR 1191 Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines

UNDERWRITERS LABORATORIES (UL)

UL Bld Mat Dir (updated continuously online) Building Materials Directory

1.2 SUBMITTALS

Government approval is required for submittals with a "G" designation;

submittals not having a "G" designation are for Contractor Quality Control approval. Submittals with an "S" are for inclusion in the Sustainability eNotebook, in conformance with Section 01 33 29 SUSTAINABILITY REPORTING.

Submit the following in accordance with Section 01 33 00 SUBMITTAL

PROCEDURES:

SD-02 Shop Drawings

Manufacturer's Detail Drawings ; G

Verification of Existing Conditions ; G

Hardware Schedule ; G

Keying System ; G

SECTION 08 71 00 Page 2

SD-03 Product Data

Hardware Items ; G

SD-08 Manufacturer's Instructions

Installation

SD-10 Operation and Maintenance Data

Hardware Schedule Items, Data Package 1; G

SD-11 Closeout Submittals

Key Bitting

1.3 SHOP DRAWINGS

Submit manufacturer's detail drawings indicating all hardware assembly components and interface with adjacent construction. Indicate power components and wiring coordination for electrified hardware. Base shop drawings on verified field measurements and include verification of existing conditions .

1.4 PRODUCT DATA

Indicate fire-ratings at applicable components. Provide documentation of ABA/ADA accessibility compliance of applicable components, as required by 36 CFR 1191 Appendix D - Technical.

1.5 HARDWARE SCHEDULE

Prepare and submit hardware schedule in the following form:

Hardware Item

Quantity Size Reference Publi-cation Type No.

Finish Mfr Name and Catalog No.

Key Control Symbols

UL

Mark (If fire-rated and listed)

BHMA

Finish Desig-nation

In addition, submit hardware schedule data package 1 in accordance with Section 01 78 23 OPERATION AND MAINTENANCE DATA.

1.6 KEY BITTING CHART REQUIREMENTS

1.6.1 Requirements

Submit key bitting charts to the Contracting Officer prior to completion of the work. Include:

a. Complete listing of all keys (e.g. AA1 and AA2).

b. Complete listing of all key cuts (AA1-123456, AA2-123458).

c. Tabulation showing which key fits which door.

SECTION 08 71 00 Page 3

d. Copy of floor plan showing doors and door numbers.

e. Listing of 20 percent more key cuts than are presently required in each master system.

1.7 QUALITY ASSURANCE

1.7.1 Hardware Manufacturers and Modifications

Provide, as far as feasible, locks, hinges, and closers of one lock, hinge, or closer manufacturer's make. Modify hardware as necessary to provide features indicated or specified.

1.7.2 Key Shop Drawings Coordination Meeting

Prior to the submission of the key shop drawing, the Contracting Officer, Contractor, Door Hardware Subcontractor, using Activity and Base Locksmith must meet to discuss and coordinate key requirements for the facility.

1.8 DELIVERY, STORAGE, AND HANDLING

Deliver hardware in original individual containers, complete with necessary appurtenances including fasteners and instructions. Mark each individual container with item number as shown on hardware schedule.

Deliver permanent keys and removable cores to the Contracting Officer, either directly or by certified mail. Deliver construction master keys with the locks.

PART 2 PRODUCTS

2.1 TEMPLATE HARDWARE

Hardware applied to metal or to prefinished doors must be manufactured using a template. Provide templates to door and frame manufacturers in accordance with ANSI/BHMA A156.7 for template hinges. Coordinate hardware items to prevent interference with other hardware.

2.2 HARDWARE FOR FIRE DOORS AND EXIT DOORS

Provide all hardware necessary to meet the requirements of NFPA 72 for door alarms, NFPA 80 for fire doors, NFPA 101 for exit doors, NFPA 252 for fire tests of door assemblies, ABA/ADA accessibility requirements, and all other requirements indicated, even if such hardware is not specifically mentioned in paragraph HARDWARE SCHEDULE. Provide Underwriters Laboratories, Inc. labels for such hardware in accordance with UL Bld Mat Dir or equivalent labels in accordance with another testing laboratory approved in writing by the Contracting Officer.

2.3 HARDWARE ITEMS

Clearly and permanently mark with the manufacturer's name or trademark, hinges, pivots, locks, latches, exit devices, bolts and closers where the identifying mark is visible after the item is installed. For closers with covers, the name or trademark may be beneath the cover. Coordinate electrified door hardware components with corresponding components specified in Division 28 ELECTRONIC SECURITY SYSTEMS (ESS).

SECTION 08 71 00 Page 4

2.3.1 Hinges

Provide in accordance with ANSI/BHMA A156.1 . Provide hinges that are 4-1/2 by 4-1/2 inch unless otherwise indicated. Construct loose pin hinges for interior doors and reverse-bevel exterior doors so that pins are non-removable when door is closed. Other anti-friction bearing hinges may be provided in lieu of ball bearing hinges.

2.3.2 Continuous Hinges

Where continuous hinges are required, provide in accordance with

ANSI/BHMA A156.26 .

2.3.3 Locks and Latches

2.3.3.1 Mortise Locks and Latches

Provide in accordance with ANSI/BHMA A156.13 , Series 1000, Operational Grade 1, Security Grade 2. Provide knobs and roses of mortise locks with screwless shanks and no exposed screws.

2.3.3.2 Bored Locks and Latches

Provide in accordance with ANSI/BHMA A156.2 , Series 4000, Grade 1.

2.3.4 Exit Devices

Provide in accordance with ANSI/BHMA A156.3 , Grade 1. Provide adjustable strikes for rim type and vertical rod devices. Provide open back strikes for pairs of doors with mortise and vertical rod devices. Provide touch bars in lieu of conventional crossbars and arms.

2.3.5 Exit Locks With Alarm

Provide in accordance with ANSI/BHMA A156.3 and ANSI/BHMA A156.29 , Type E0431 (with full width horizontal actuating bar) for single doors; Type E0431 (with actuating bar) or E0471 (with actuating bar and top and bottom bolts, both leaves active) for pairs of doors, unless otherwise specified.

Provide door alarms integrated with the fire alarm system in accordance with NFPA 72 .

2.3.6 Cylinders and Cores

Provide cylinders and cores for new locks, including locks provided under other sections of this specification. Provide cylinders and cores with seven pin tumblers. Provide cylinders from the products of one manufacturer, and provide cores from the products of one manufacturer.

Rim cylinders, mortise cylinders, and knobs of bored locksets have interchangeable cores which are removable by special control keys. Stamp each interchangeable core with a key control symbol in a concealed place on the core.

2.3.7 Electrified Hardware

Comply with the requirements of NFPA 70 for wiring of electrified hardware.

2.3.7.1 Electric Strikes and Frame Mounted Actuators

Provide in accordance with ANSI/BHMA A156.31 , Grade 1. Provide electric

SECTION 08 71 00 Page 5 strikes and actuators as required to meet operational requirements.

Provide electric strikes that remain secure during power failure. Provide a separate power supply for electric strikes, other locking devices and ancillary parts. Provide strikes and actuators with a minimum opening force of 2300 pounds .

Provide facility interface devices that use direct current (dc) power to energize the solenoids. Provide electric strikes and actuators that incorporate end-of-line resistors to facilitate line supervision by the system. If not incorporated into the electric strike or local controller, provide metal oxide resistors (MOVs) to protect the controller from reverse current surges.

2.3.7.1.1 Solenoid

Provide actuating solenoid for strikes and actuators that are rated for continuous duty, cannot dissipate more than 12 Watts and must operate on 12 or 24 Volts dc. Inrush current cannot exceed 1 ampere and the holding current cannot be greater than 500 milliamperes. Actuating solenoid must move from fully secure to fully open positions in less than 500 milliseconds.

2.3.7.1.2 Signal Switches

Provide strikes and actuators with signal switches to indicate to the system when the bolt is not engaged or the strike mechanism is unlocked.

Signal switches must report a forced entry to the system.

2.3.7.1.3 Tamper Resistance

Provide strike guards that prevent tampering with the latch bolt of the locking hardware or the latch bolt keeper of the electric strike. Strike guards to bolt through the door using tamper resistant screws. Provide strike guards made of 1/8 inch thick brass and that are 11-1/14 inch high by 1-5/8 inch wide , with a minimum 5/32 inch wide offset.

2.3.7.1.4 Coordination

Provide electric strikes and actuators of a size, weight and profile compatible with each specified door frame. Field verify installation clearances prior to procurement.

2.3.7.1.5 Mounting Method

Provide electric strikes and actuators suitable for use with single and double doors, with mortise or rim type hardware specified, and for right or left hand mounting as specified. In double door installations, locate the lock in the active leaf and monitor the fixed leaf.

2.3.7.2 Electrified Mortise Locks

Provide in accordance with ANSI/BHMA A156.25 , Grade 1. Provide electrified mortise locks that remain secure during power failure.

Provide facility interface devices that use dc power to energize solenoids. Provide solenoids, resisters, and signal switches in accordance with paragraph ELECTRIC STRIKES AND FRAME MOUNTED ACTUATORS.

SECTION 08 71 00 Page 6

2.3.7.2.1 Power Transfer Hinges

Provide power transfer hinges with each electrified lock that route power and monitoring signals from the lockset to the door frame. Coordinate power transfer hinges with door frames.

2.3.7.3 Card Readers and Keypad Access Control Hardware

Coordinate access control hardware with corresponding devices and systems specified in Division 28 ELECTRONIC SECURITY SYSTEMS (ESS).

2.3.7.4 Electromagnetic Locks

Provide in accordance with ANSI/BHMA A156.23 , Grade 1. Provide electromagnetic locks that do not contain any moving parts and depend solely upon electromagnetism to secure a portal by generating at least 1200 pounds of holding force. The lock must interface with the local processors without external, internal or functional alteration of the local processor. The electromagnetic lock must incorporate an end of line resistor to facilitate line supervision by the system. Provide metal-oxide resistors (MOVs) to protect controllers from reverse current surges, if not incorporated into the electromagnetic lock or local controller.

2.3.7.4.1 Armature

Provide electromagnetic locks with internal circuitry to eliminate residual magnetism and inductive kickback. Provide atuating armature that operates on 12 or 24 Volts dc and cannot dissipate more than 12 Watts.

Holding current must be less than 500 milliamperes. Actuating armature must take less than 300 milliseconds to change the status of the lock from fully secure to fully open or fully open to fully secure.

2.3.7.4.2 Tamper Resistance

Provide lock mechanism encased in hardened guard barriers to deter forced entry.

2.3.7.4.3 Mounting Method

Provide electromagnetic lock suitable for use with single and double door with mortise or rim type hardware and compatible with right or left hand mounting.

2.3.8 Keying System

Provide an extension of the existing keying system.

2.3.9 Lock Trim

Provide cast, forged, or heavy wrought construction and commercial plain design for lock trim.

2.3.9.1 Lever Handles

Provide lever handles where indicated in the Hardware Schedule. Provide in accordance with ANSI/BHMA A156.3 for mortise locks of lever handles for

SECTION 08 71 00 Page 7 exit devices. Provide lever handle locks with a breakaway feature (such as a weakened spindle or a shear key) to prevent irreparable damage to the lock when force in excess of that specified in ANSI/BHMA A156.13 is applied to the lever handle. Provide lever handles return to within 1/2 inch of the door face.

2.3.10 Keys

Furnish one file key, one duplicate key, and one working key for each key change and for each master and grand master keying system. Furnish one additional working key for each lock of each keyed-alike group. Stamp each key with appropriate key control symbol and "U.S. property - do not duplicate." Do not place room number on keys.

2.3.11 Door Bolts

Provide in accordance with ANSI/BHMA A156.16 . Provide dustproof strikes for bottom bolts, except at doors having metal thresholds. Provide automatic latching flush bolts in accordance with ANSI/BHMA A156.3 , Type 25.

2.3.12 Closers

Provide in accordance with ANSI/BHMA A156.4 , Series C02000, Grade 1, with PT 4C. Provide with brackets, arms, mounting devices, fasteners, and other features necessary for the particular application. Size closers in accordance with manufacturer's printed recommendations, or provide multi-size closers, Sizes 1 through 6, and list sizes in the Hardware Schedule. Provide manufacturer's 10 year warranty.

2.3.12.1 Identification Marking

Engrave each closer with manufacturer's name or trademark, date of manufacture, and manufacturer's size designation in locations that will be visible after installation.

2.3.13 Overhead Holders

Provide in accordance with ANSI/BHMA A156.8 .

2.3.14 Door Protection Plates

Provide in accordance with ANSI/BHMA A156.6 .

2.3.14.1 Sizes of Armor Mop and Kick Plates

2 inch less than door width for single doors; 1 inch less than door width for pairs of doors. Provide 10 inch kick plates for flush doors .

Provide a minimum 36 inch armor plates for flush doors and completely cover lower panels of panel doors, except 16 inch high armor plates on fire doors. Provide 6 inch mop plates.

2.3.15 Door Stops and Silencers

Provide in accordance with ANSI/BHMA A156.16 . Silencers Type L03011.

Provide three silencers for each single door, two for each pair.

SECTION 08 71 00 Page 8

2.3.16 Thresholds

Provide in accordance with ANSI/BHMA A156.21 . Use J35100, with vinyl or silicone rubber insert in face of stop, for exterior doors opening out, unless specified otherwise.

2.3.17 Weatherstripping Gasketing

Provide in accordance with ANSI/BHMA A156.22 . Provide the type and function designation where specified in paragraph HARDWARE SCHEDULE.

Provide a set to include head and jamb seals, sweep strips, and, for pairs of doors, astragals. Air leakage of weatherstripped doors not to exceed

0.5 cubic feet per minute of air per square foot of door area when tested in accordance with ASTM E283. Provide weatherstripping with one of the following:

2.3.17.1 Extruded Aluminum Retainers

Extruded aluminum retainers not less than 0.050 inch wall thickness with vinyl, neoprene, silicone rubber, or polyurethane inserts. Provide clear (natural) anodized aluminum.

2.3.17.2 Interlocking Type

Zinc or bronze not less than 0.018 inch thick.

2.3.17.3 Spring Tension Type

Spring bronze or stainless steel not less than 0.008 inch thick.

2.3.18 Lightproofing and Soundproofing Gasketing

Provide in accordance with ANSI/BHMA A156.22 . Provide adjustable doorstops at heads,jambs and automatic door bottoms in accordance with the hardware set, of extruded aluminum, clear (natural) anodized, surface applied, with vinyl fin seals between plunger and housing. Provide doorstops with solid neoprene tube, silicone rubber, or closed cell sponge gasket. Provide door bottoms with adjustable operating rod and silicone rubber or closed cell sponge neoprene gasket. Provide doorstops that are mitered at corners. Provide type and function designation where specified in paragraph HARDWARE SETS.

2.3.19 Rain Drips

Provide in accordance with ANSI/BHMA A156.22 . Provide extruded aluminum rain drips, not less than 0.08 inch thick, clear anodized finish. Provide the manufacturer's full range of color choices to the Contracting Officer for color selection. Provide rain drips with a 4 inch overlap on each side of each exterior door that is not protected by an awning, roof, eave or other horizontal projection. Set drips in sealant and fasten with stainless steel screws.

2.3.19.1 Door Rain Drips

Approximately 1-1/2 inch high by 5/8 inch projection. Align bottom with bottom edge of door.

SECTION 08 71 00 Page 9

2.3.19.2 Overhead Rain Drips

Approximately 1-1/2 inch high by 2-1/2 inch projection. Align bottom with door frame rabbet.

2.3.20 Auxiliary Hardware (Other than locks)

Provide in accordance with ANSI/BHMA A156.16 , Grade 1.

2.3.21 Sliding and Folding Door Hardware

Provide in accordance with ANSI/BHMA A156.14 , Grade 1. Finishes to match other hardware specified herein.

2.3.22 Special Tools

Provide special tools, such as spanner and socket wrenches and dogging keys, as required to service and adjust hardware items.

2.4 FASTENERS

Provide fasteners of type, quality, size, and quantity appropriate to the specific application. Fastener finish to match hardware. Provide stainless steel or nonferrous metal fasteners in locations exposed to weather. Verify metals in contact with one another are compatible and will avoid galvanic corrosion when exposed to weather.

2.5 FINISHES

Provide in accordance with ANSI/BHMA A156.18 . Provide hardware in BHMA 630 finish (satin stainless steel), unless specified otherwise. Provide items not manufactured in stainless steel in BHMA 626 finish (satin chromium plated) over brass or bronze, except aluminum paint finish for surface door closers, and except BHMA 652 finish (satin chromium plated) for steel hinges. Provide hinges for exterior doors in stainless steel with BHMA 630 finish or chromium plated brass or bronze with BHMA 626 finish. Furnish exit devices in BHMA 626 finish in lieu of BHMA 630 finish except where BHMA 630 is specified under paragraph HARDWARE SETS.

Match exposed parts of concealed closers to lock and door trim. Match hardware finish for aluminum doors to the doors.

2.6 KEY CABINET AND CONTROL SYSTEM

Provide in accordance with ANSI/BHMA A156.5 , Type E8341 (125 hooks) .

PART 3 EXECUTION

3.1 INSTALLATION

Provide hardware in accordance with manufacturers' printed installation instructions. Fasten hardware to wood surfaces with full-threaded wood screws or sheet metal screws. Provide machine screws set in expansion shields for fastening hardware to solid concrete and masonry surfaces.

Provide toggle bolts where required for fastening to hollow core construction. Provide through bolts where necessary for satisfactory installation.

SECTION 08 71 00 Page 10

3.1.1 Weatherstripping Installation

Provide full contact, weathertight seals that allow operation of doors without binding the weatherstripping.

3.1.1.1 Stop Applied Weatherstripping

Fasten in place with color matched sheet metal screws not more than 9 inch on center after doors and frames have been finish painted.

3.1.1.2 Interlocking Type Weatherstripping

Provide interlocking, self adjusting type on heads and jambs and flexible hook type at sills. Nail weatherstripping to door 1 inch on center and to heads and jambs at 4 inch on center.

3.1.1.3 Spring Tension Type Weatherstripping

Provide spring tension type on heads and jambs. Provide bronze nails with bronze. Provide stainless steel nails with stainless steel. Space nails not more than 1-1/2 inch on center.

3.1.2 Lightproofing and Soundproofing Installation

Provide as specified for stop applied weatherstripping.

3.1.3 Threshold Installation

Extend thresholds the full width of the opening and notch end for jamb stops. Set thresholds in a full bed of sealant and anchor to floor with cadmium-plated, countersunk, steel screws in expansion sleeves. For aluminum thresholds placed on top of concrete surfaces, coat the underside surfaces that are in contact with the concrete with fluid applied waterproofing as a separation measure prior to placement.

3.2 FIRE DOORS AND EXIT DOORS

Provide hardware in accordance with NFPA 72 for door alarms, NFPA 80 for fire doors, NFPA 101 for exit doors, and NFPA 252 for fire tests of door assemblies. .

3.3 HARDWARE LOCATIONS

Provide in accordance with SDI/DOOR A250.8 , unless indicated or specified otherwise.

a. Kick and Armor Plates: Push side of single-acting doors. Both sides of double-acting doors.

b. Mop Plates: Bottom flush with bottom of door.

3.4 KEY CABINET AND CONTROL SYSTEM

Locate where directed. Tag one set of file keys and one set of duplicate keys. Place other keys in appropriately marked envelopes, or tag each key. Provide complete instructions for setup and use of key control system. On tags and envelopes, indicate door and room numbers or master or grand master key.

SECTION 08 71 00 Page 11

3.5 FIELD QUALITY CONTROL

After installation, protect hardware from paint, stains, blemishes, and other damage until acceptance of work. Submit notice of testing 15 days before scheduled, so that testing can be witnessed by the Contracting Officer. Adjust hinges, locks, latches, bolts, holders, closers, and other items to operate properly. Demonstrate that permanent keys operate respective locks, and give keys to the Contracting Officer. Correct, repair, and finish, errors in cutting and fitting and damage to adjoining work.

3.6 HARDWARE SETS

SECTION 08 71 00 Page 12

Provide hardware for aluminum doors under this section. Deliver Hardware templates and hardware, except field applied hardware, to the aluminum door and frame manufacturer for use in fabricating doors and frames.

Hardware Sets

Set: 1.0 Doors: 100A, 100AA, 100B, 100C

2 Continuous Hinge (A31331G)* 2 Electric Power Transfer* 1 Removable Mullion (Type 22)* 1 Exit Device (Type 1, 03, E01, E04)* 1 Exit Device (Type 1, 02, E01, E04)* 4 Interchangeable Core (E09241)* 1 Mullion Cylinder (E09251)* 2 Door Pull (J402)* 2 Surface Closer (C02021-PT4G)* 1 Threshold (J36100)* 1 Rain Guard (R0Y976)* 2 Sweep (R3D534)* 2 Frame Harness* 2 Door Harness* 2 Position Switch (E08)* 1 Card Reader 1 Power Supply*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Perimeter/meeting stile seals by frame/door supplier.

o Electronic Operation: Valid card or key retracts latchbolt. Request to exit shows authorized egress. Free egress at all times. In case of power loss, door remains locked and latched.

Set: 2.0 Doors: 125B

1 Continuous Hinge (A31331G)* 1 Electric Power Transfer* 1 Exit Device (Type 1, 03, E01, E04)* 2 Interchangeable Core (E09241)* 1 Door Pull (J402)* 1 Surface Closer (C02021-PT4G)* 1 Kick Plate (J102)* 1 Threshold (J36100)* 1 Rain Guard (R0Y976)* 1 Gasketing (R3E164)* 1 Sweep (R3D534)* 1 Frame Harness* 1 Door Harness* 1 Position Switch (E08)* 1 Card Reader 1 Power Supply*

SECTION 08 71 00 Page 13

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Electronic Operation: Valid card or key retracts latchbolt. Request to exit shows authorized egress. Free egress at all times. In case of power loss, door remains locked and latched.

Set: 3.0 Doors: 122, 127B, 127C

1 Continuous Hinge (A31031G)* 1 Exit Device (Type 1, 03)* 2 Interchangeable Core (E09241)* 1 Door Pull (J402)* 1 Surface Closer (C02021-PT4G)* 1 Kick Plate (J102)* 1 Threshold (J36100)* 1 Rain Guard (R0Y976)* 1 Gasketing (R3E164)* 1 Sweep (R3D534)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 4.0 Doors: 123A

2 Continuous Hinge (A31031G)* 2 Flush Bolt (L04251/L04261)* 1 Storeroom Lock (F07)* 1 Interchangeable Core (E09241)* 1 Surf Overhead Stop (C02541)* 1 Surface Closer (C02021-PT4G)* 2 Kick Plate (J102)* 1 Threshold (J36100)* 1 Rain Guard (R0Y976)* 1 Gasketing (R3E164)* 2 Sweep (R3D534)* 1 Astragal (R0Y634)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy with the manufacturer.

Set: 5.0 Doors: 120A, 126B, 163A

1 Continuous Hinge (A31031G)* 1 Classroom Lock (F05)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02021-PT4G)* 1 Kick Plate (J102)* 1 Threshold (J36100)* 1 Rain Guard (R0Y976)* 1 Gasketing (R3E164)* 1 Sweep (R3D534)*

SECTION 08 71 00 Page 14

Notes: *Waiver may be required to comply with Buy American Act. Compliancy with the manufacturer.

Set: 6.0 Doors: 100AB

2 Continuous Hinge (A31331G)* 2 Electric Power Transfer* 1 Removable Mullion (Type 22)* 1 Exit Device (Type 1, 03, E01, E04)* 1 Exit Device (Type 1, 02, E01, E04)* 3 Interchangeable Core (E09241)* 1 Mullion Cylinder (E09251)* 2 Door Pull (J402)* 2 Surface Closer (C02021-PT4G)* 2 Frame Harness* 2 Door Harness* 2 Position Switch (E08)* 1 Card Reader 1 Remote Release Push Button* 1 Power Supply*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Perimeter/meeting stile seals by frame/door supplier.

o Electronic Operation: Valid card, remote release push button or key retracts latchbolt. Request to exit shows authorized egress. Free egress at all times. In case of power loss, door remains locked and latched.

Set: 7.0 Doors: 129

6 Hinge (A8112)* 2 Flush Bolt (L04251/L04261)* 1 Dust Proof Strike (L04021)* 1 Storeroom Lock (F07)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 2 Kick Plate (J102)* 2 Door Stop (L02251 / L02121)* 2 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 8.0 Doors: 100E, 113, 119, 121A, 130, 139, 140, 142

3 Hinge (A8112)* 1 Storeroom Lock (F07)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)*

SECTION 08 71 00 Page 15

3 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 9.0 Doors: 101, 102, 105, 106, 107, 108, 110, 111, 112, 115, 116, 126AA, 136, 137, 138, 143, 144, 145, 146, 147, 148, 151, 153, 154, 155, 156, 158, 159, 160, 161

3 Hinge (A8112)* 1 Office Lock (F04)* 1 Interchangeable Core (E09241)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 10.0 Doors: 100DA, 100DB

6 Hinge (A8112)* 2 Flush Bolt (L04251/L04261)* 1 Dust Proof Strike (L04021)* 1 Storeroom Lock (F07)* 1 Interchangeable Core (E09241)* 1 Surf Overhead Stop (C02541)* 1 Surface Closer (C02021-PT4G)* 2 Kick Plate (J102)* 2 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 11.0 Doors: 134A, 134B

3 Hinge (A8111)* 1 Exit Device (Type 1, 08)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 12.0 Doors: 100CA, 118B, 135, 162

3 Hinge (A8112)* 1 Classroom Lock (F05)* 1 Interchangeable Core (E09241)*

SECTION 08 71 00 Page 16

1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 13.0 Doors: 124B

3 Hinge (A8112)* 1 Classroom Lock (F05)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)* 1 Adhesive Gasketing (R0Y154)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 14.0 Doors: 103, 104, 131, 132A, 132B

3 Hinge (A8111)* 1 Push Plate (J301)* 1 Door Pull w/ Plate (J405)* 1 Foot Pull* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Mop Plate (J103)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Mop plate at inswinging doors only.

Set: 15.0 Doors: 120B, 125C, 127D, 128, 163B

0 All Hardware

Notes:

Set: 16.0 Doors: 100BA, 109, 114, 118A, 124A, 126A, 141, 149, 152, 157

3 Hinge (A8111)* 1 Electric Power Transfer* 1 Fail Secure Lock (E01, E06)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)*

SECTION 08 71 00 Page 17

3 Silencer (L03011)* 1 Frame Harness* 1 Door Harness* 1 Position Switch (E08)* 1 Card Reader 1 Power Supply*

Notes:

*Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Electronic Operation: Valid card unlocks outside lever or key retracts latchbolt. Request to exit shows authorized egress. Free egress at all times. In case of power loss, door remains locked and latched.

Set: 17.0 Doors: 127A, 133B, 133D

6 Hinge (A8111)* 2 Exit Device (Type 2, 08)* 2 Interchangeable Core (E09241)* 2 Surface Closer (C02011 / C02021)* 2 Kick Plate (J102)* 2 Door Stop (L02251 / L02121)* 2 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 18.0 Doors: 125A

3 Hinge (A8111)* 1 Electric Power Transfer* 1 Fail Secure Lock (E01, E06)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)* 1 Adhesive Gasketing (R0Y154)* 1 Frame Harness* 1 Door Harness* 1 Position Switch (E08)* 1 Card Reader 1 Power Supply*

Notes:

*Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Electronic Operation: Valid card unlocks outside lever or key retracts

Set: 19.0 Doors: 121

SECTION 08 71 00 Page 18

3 Hinge (A8111)* 1 Electric Power Transfer* 1 Fail Secure Lock (E01, E06)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)* 1 Frame Harness* 1 Door Harness* 1 Position Switch (E08)* 1 Card Reader 1 Power Supply*

Notes:

*Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o STC seals by door supplier.

o Electronic Operation: Valid card unlocks outside lever or key retracts

Set: 20.0 Doors: 123B

3 Hinge (A8111)* 1 Exit Device (Type 1, 01, E0431)* 1 Interchangeable Core (E09241)* 1 Surface Closer (C02021-PT4G)* 1 Kick Plate (J102)* 1 Adhesive Gasketing (R0Y154)*

Notes:

*Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Alarmed exit. Key arms/disarms alarm function. Free egress at all times.

Set: 21.0 Doors: 133C

2 Continuous Hinge (A31331G)* 2 Electric Power Transfer* 1 Removable Mullion (Type 22)* 1 Exit Device (Type 1, 03, E01, E04)* 1 Exit Device (Type 1, 02, E01, E04)* 3 Interchangeable Core (E09241)* 1 Mullion Cylinder (E09251)* 2 Door Pull (J402)* 2 Surface Closer (C02021-PT4G)* 1 Threshold (J36100)* 1 Rain Guard (R0Y976)* 1 Gasketing (R3E164)* 2 Sweep (R3D534)* 1 Astragal (R3E734)*

SECTION 08 71 00 Page 19

2 Frame Harness* 2 Door Harness* 2 Position Switch (E08)* 1 Card Reader 1 Power Supply*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

o Electronic Operation: Valid card or key retracts latchbolt. Request to exit shows authorized egress. Free egress at all times. In case of power loss, door remains locked and latched.

Set: 22.0 Doors: 133A

3 Hinge (A8111)* 1 Exit Device (Type 1, 01)* 1 Surface Closer (C02011 / C02021)* 1 Kick Plate (J102)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)*

Notes:

*Waiver may be required to comply with Buy American Act. Compliancy of this product to current Buy American-type regulations must be validated with the manufacturer.

Set: 23.0 Doors: 147A

3 Hinge (A8112)* 1 Storeroom Lock (F07)* 1 Interchangeable Core (E09241)* 1 Door Stop (L02251 / L02121)* 3 Silencer (L03011)*

Notes: *Waiver may be required to comply with Buy American Act. Compliancy with the manufacturer.

-- End of Section --

SECTION 08 71 00 Page 20