Elect 035.pdf

ELECTRICAL ABBREVIATION KEY

AFF ABOVE FINISHED FLOOR

N.C. NORMALLY CLOSED

NIC NOT IN CONTRACT

N.O. NORMALLY OPEN

SV SOLENOID VALVE

ABBR: DESCRIPTION:

TYP TYPICAL

C CONDUIT

UNO UNLESS NOTED OTHERWISE

GFI GROUND FAULT INTERRUPTER

1. THE COMPLETE INSTALLATION SHALL BE IN ACCORDANCE WITH THE ADA STANDARDS FOR

ACCESSIBLE DESIGN. REFER TO THE ADA GUIDELINES FOR ALL CONFIGURATION DETAILS

ON THIS PAGE FOR ADDITIONAL INFORMATION.

2. CIRCUIT NUMBERS ARE SHOWN FOR CIRCUIT IDENTIFICATION. CIRCUITING SHALL AGREE

WITH NUMBERING ON THE PANEL PROVIDED. COMMON NEUTRALS MAY NOT BE USED FOR

BRANCH CIRCUITS. BALANCE THE LOAD ON PANEL AS EVENLY AS POSSIBLE BETWEEN

EACH PHASE.

3. LIFE SAFETY, CRITICAL, EQUIPMENT BRANCH WIRING FOR FEEDERS AND BRANCH CIRCUITS

SHALL BE ROUTED IN SEPARATE RACEWAY, JUNCTION BOXES, PULL BOXES, AND CABINETS.

WIRING FOR EACH BRANCH SHALL BE INDEPENDENT FROM OTHER BRANCHES, INCLUDING

THE NORMAL BRANCH.

4. FLUSH MOUNT ALL LIGHTING CONTROL DEVICES AT +42" FROM FLOOR (CENTERLINE

DIMENSION), EXCEPT WHERE OTHERWISE NOTED. DEVICES MAY BE SURFACE MOUNTED

WHEN CONDUIT IS SPECIFIED EXPOSED.

5. FLUSH MOUNT ALL DUPLEX RECEPTACLES AND TECHNOLOGY OUTLETS AT +18" FROM

FLOOR (CENTERLINE DIMENSION), EXCEPT WHERE OTHERWISE NOTED. RECEPTACLES AND

OUTLETS MAY BE SURFACE MOUNTED WHEN CONDUIT IS SPECIFIED EXPOSED.

6. ALL MATERIALS USED TO SEAL PENETRATIONS OF FIRE RATED WALLS AND FLOORS SHALL

BE TESTED AND CERTIFIED AS A SYSTEM PER ASTM E814 STANDARDS FOR FIRE TESTS OF

THROUGH-PENETRATION FIRESTOPS. REFER TO [27 05 03 AND 28 05 03] [DIVISION 7] [26 05 03]

FOR ADDITIONAL INFORMATION AND REQUIREMENTS SPECIFIC TO FIRESTOPPING.

7. CONNECTION FOR ELECTRIC WATER COOLERS (EWC) SHALL BE A JUNCTION BOX

CONCEALED BEHIND WATER COOLER ACCESS PLATE OR BE A GFI RECEPTACLE LOCATED

DIRECTLY BELOW AND CENTERED ON EWC. CONTRACTOR SHALL VERIFY TYPE OF EWC TO

BE INSTALLED.

8. MOUNT ALL FIRE ALARM PULL STATIONS AT +42" FROM FLOOR (CENTERLINE DIMENSION)

EXCEPT WHERE OTHERWISE NOTED.

9. INSTALL ALL WALL MOUNTED FIRE ALARM NOTIFICATION DEVICES AT 90" ABOVE FINISHED

FLOOR OR 6" BELOW THE CEILING, WHICHEVER IS LOWER, EXCEPT WHERE OTHERWISE

NOTED. HEIGHT SHALL BE MEASURED TO THE TOP OF THE DEVICE.

10. CONTRACTOR SHALL COORDINATE THE LOCATION OF ALL CEILING MOUNTED DEVICES AND

EQUIPMENT WITH LUMINAIRES, SPRINKLER, AND CEILING DIFFUSERS. CENTER ALL DEVICES

IN CEILING TILE PATTERN. SMOKE DETECTORS AND OCCUPANCY/VACANCY SENSORS

SHALL BE LOCATED NO CLOSER THAN 3 FEET TO AN AIR SUPPLY DIFFUSER OR RETURN

GRILLE.

11. CONTRACTOR SHALL VERIFY ALL FURNITURE, MODULAR FURNITURE, AND EQUIPMENT

LOCATIONS WITH ARCHITECTURAL PLANS, ELEVATIONS, AND REVIEWED SHOP DRAWINGS.

PRIOR TO MAKING THE ACTUAL ELECTRICAL INSTALLATION, THIS CONTRACTOR SHALL

ADJUST RECEPTACLES, OUTLETS, OR CONNECTION LOCATIONS TO ACCOMMODATE

FURNITURE AND/OR EQUIPMENT.

12. ELECTRICAL AND TECHNOLOGY EQUIPMENT SHALL BE MOUNTED TO AVOID IMPEDANCE OF,

OPERATION OF, AND/OR ACCESS TO ELECTRICAL AND MECHANICAL EQUIPMENT. ALL

MOUNTING OF ELECTRICAL AND TELECOMMUNICATIONS EQUIPMENT, ON EQUIPMENT

SUPPLIED BY ANOTHER CONTRACTOR, SHALL BE APPROVED IN ADVANCE BY THE OTHER

CONTRACTOR.

13. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL OPENINGS REQUIRED IN WALLS. ALL

OPENINGS SHALL BE REPAIRED TO MATCH EXISTING BY A QUALIFIED CONTRACTOR AT THE

EXPENSE OF THIS CONTRACTOR. ALL CONDUITS THROUGH WALLS SHALL BE GROUTED OR

SEALED INTO OPENINGS.

14. ALL WELDING SHALL BE ACCORDING TO AMERICAN WELDING SOCIETY STANDARDS.

CONTRACTOR SHALL FURNISH TO THE ARCHITECT/ENGINEER CERTIFICATES QUALIFYING

EACH WELDER, PRIOR TO START OF WORK. THE ARCHITECT/ENGINEER RESERVES THE

RIGHT TO REQUIRE QUALIFYING DEMONSTRATION, AT THE CONTRACTOR'S EXPENSE, OF

ANY WELDERS ASSIGNED TO THE JOB.

15. CONTRACTOR SHALL REMOVE AND REINSTALL ALL CEILING TILES AS REQUIRED FOR THE

EXECUTION OF ELECTRICAL WORK. CONTRACTOR SHALL REPLACE CEILING TILES WITH

IDENTICAL MATERIAL WHERE DAMAGED BY THIS CONTRACTOR.

16. REFER TO ARCHITECTURAL REFLECTED CEILING PLAN, ELECTRICAL, TECHNOLOGY

AUDIO/VISUAL, AND OTHER ELECTRICAL PLANS FOR EXACT LOCATIONS OF ALL CEILING

MOUNTED DEVICES, OTHER THAN SPRINKLERS.

17. ELECTRICAL INDENTIFICATION. REFER TO SPECIFICATION SECTION[26 05 53] FOR

COLOR/LABEL REQUIREMENTS FOR CONDUIT, BOX, CABLE/WIRE, AND EQUIPMENT.

ELECTRICAL INSTALLATION NOTES:

SW-1P 26 09 33 SWITCH - SINGLE POLE

SW-COMB 26 09 33 COMBINATION SWITCH AND RECEPTACLE

SW-1P-EM 26 09 33 SWITCH - EMERGENCYE

SW-2P 26 09 33 SWITCH - TWO POLE2

SW-3W 26 09 33 SWITCH - THREE WAY3

SW-3W-EM 26 09 33 SWITCH - THREE WAY - EMERGENCY3E

SW-4W 26 09 33 SWITCH - FOUR WAY4

SW-4W-EM 26 09 33 SWITCH - FOUR WAY - EMERGENCY4E

SW-1P-WP 26 09 33 SWITCH - WEATHERPROOFW

SW-1P-EX 26 09 33 SWITCH - EXPLOSION PROOFX

SW-1P-PL 26 09 33 SWITCH - PILOT LIGHTP

SW-1P-LH 26 09 33 SWITCH - LIGHTED HANDLEL

SW-1P-ADJ 26 09 33 SWITCH - LOCAL TIMER - USER ADJUSTABLET

SW-1P-060 26 09 33 SWITCH - LOCAL TIMER - SPRING WOUND60

SW-A-TPCO 26 09 33 SWITCH - THREE POSITION-CENTER OFFC

SW-1P-M 26 09 33 SWITCH - MOMENTARY CONTACTM

SW-OC-P-O SWITCH - OCCUPANCY SENSOR

WALL SWITCH

O

SW-OC-P-O2 SWITCH - OCCUPANCY SENSOR AND

DUAL SWITCH

O2

OC SW-OC-P-P OCCUPANCY SENSOR - PASSIVE INFRARED

360 DEGREE COVERAGEP

OC SW-OC-P-P2 OCCUPANCY SENSOR - PASSIVE INFRARED

100 DEGREE COVERAGEP2

OC SW-OC-U OCCUPANCY SENSOR - ULTRASONIC 360

DEGREE COVERAGEU

OC SW-OC-U2 OCCUPANCY SENSOR - ULTRASONIC 35'X30'

HAND MOTION COVERAGEU2

OC SW-OC-U-A OCCUPANCY SENSOR - ULTRASONIC TWO

SIDED CORRIDOR COVERAGEA

OC SW-OC-D OCCUPANCY SENSOR - DUAL TECHNOLOGY

D

OC SW-OC-P-HB OCCUPANCY SENSOR - HIGH BAY

HB

OC SW-OC-P-HA OCCUPANCY SENSOR - HIGH BAY AISLE

COVERAGE

HA

ALCR ALCR20 AUTOMATIC LOAD CONTROL RELAY

BCELTS

BCELTS BRANCH CIRCUIT EMERGENCY LIGHTING

TRANSFER SWITCH 20A

LS SW-LS DAYLIGHT LEVEL SENSOR

LS SW-LS-3Z DAYLIGHT LEVEL SENSOR - 3 ZONE

LS SW-LS-D DAYLIGHT LEVEL SENSOR - 1 ZONE DIMMING

D

LS SW-LS-D-3Z DAYLIGHT LEVEL SENSOR - 3 ZONE DIMMING

3D

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

SW-1P-K SWITCH - SINGLE POLE - KEY LOCK 26 09 33

K

SW-2P-K SWITCH - TWO POLE - KEY LOCK

K2

SW-3W-K SWITCH - THREE WAY - KEY LOCK

K3

SW-4W-K SWITCH - FOUR WAY - KEY LOCK

K4

SW-D-6 DIMMER - 600 WATT

SW-D3-6 DIMMER - 600 WATT - 3 WAY

SW-D-10 DIMMER - 1000 WATT

SW-D3-10 DIMMER - 1000 WATT - 3 WAY

SW-D-15 DIMMER - 1500 WATT

SW-D3-15 DIMMER - 1500 WATT - 3 WAY

SW-D-20 DIMMER - 2000 WATT

SW-D3-20 DIMMER - 2000 WATT - 3 WAY

SW-D-LVM DIMMER - MAGNETIC BALLAST

L

SW-D-LVE DIMMER - ELECTRONIC BALLAST

E

SW-D-FL DIMMER - FLUORESCENT BALLAST

F

SW-LS-PC PHOTOCELL26 09 33PC

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

26 09 33

MD-SD-# 26 28 16 MOBILE DIAGNOSTICS SERVICE DISCONNECT.

REFER TO DISC/STA SCHEDULE

CB-# 26 28 16 CIRCUIT BREAKER - SURFACE MOUNTED.

REFER TO DISC/STA SCHEDULE

CB-# 26 28 16 CIRCUIT BREAKER - FLUSH MOUNTED.

REFER TO DISC/STA SCHEDULE

DS-#/FDS-#/DSS-# 26 28 16 DISCONNECT. REFER TO DISC/STA SCHEDULE

SW-OC-D-W OCCUPANCY SENSOR - DUAL

TECHNOLOGY - WALL MOUNTED

D

26 09 33OC

SW-OC-P-W OCCUPANCY SENSOR - PASSIVE INFRARED -

WALL MOUNTED

P

26 09 33OC

SW-OC-U-W OCCUPANCY SENSOR - ULTRASONIC - WALL

MOUNTED

U

26 09 33OC

26 09 33

26 09 33

26 09 33

26 09 33

SW-D-LED DIMMER - LED

D

26 09 33

SW-D3-LED DIMMER - LED - 3-WAY

D3

26 09 33

ELECTRICAL SYMBOL LIST

SYMBOL: TAG: SPEC

SECTION:

DESCRIPTION:

FA-LA 26 09 16 LAMP ANNUNCIATORLA

SW-DCS DIMMER CONTROL STATION26 09 33#B

SW-LCS DIMMER CONTROL STATION WITH FADERS26 09 33

TC-# TIME SWITCH 26 09 33TC

RI-TV 26 05 33 TV ANTENNA OUTLET ROUGH-INTV

FB-# 26 27 26 FLOOR BOX - DUAL COMPARTMENT

FB-# 26 27 26 FLOOR BOX - MULTI SERVICE

FB-# 26 27 26 FLOOR BOX - DUPLEX RECEPTACLE

JB 26 05 33 JUNCTION BOX

J

J

ECONN 26 05 33 ELECTRICAL CONNECTION

E

E

WW-# 26 05 35 ELECTRICAL WIREWAY w/ DEVICES SHOWN

WM-# 26 05 35 MULTI OUTLET SYSTEM

RI-TECH-C 26 05 33 TECHNOLOGY ROUGH-IN, CEILING

RI

RI-TECH-W 26 05 33 TECHNOLOGY ROUGH-IN, WALL PHONE

DPM 26 09 13/

26 24 13

DIGITAL POWER METERDPM

PANEL '###' 26 24 16 PANELBOARD - SURFACE MOUNT

PANEL '###' 26 24 16 PANELBOARD - RECESS MOUNT

IPC-# 26 24 22 INTEGRATED POWER CENTER

IPP-# 26 24 21 ISOLATED POWER PANEL

RIM 26 24 21 REMOTE LINE ISOLATION MONITORRIM

MG 26 24 21 MASTER GROUND STATION MODULEMG

PM 26 24 21 OPERATING ROOM POWER MODULEPM

GB 26 05 26 GROUND BUSGB

IBT 26 05 26 INTERSYSTEM BONDING TERMINATIONIBT

PB PB 26 09 16 MOMENTARY PUSHBUTTON OPERATOR

ES ES 26 09 16 EMERGENCY STOP, N.C. CONTACT

EPO 26 09 16 EMERGENCY STOP, N.O. CONTACTEPO

CPC 26 09 16 CONTROL POWER CABINETCPC

MX-#/MS-#

/CB-#/CS-#

26 24 19 MANUAL SWITCH / STARTER / COMBINATION

STARTER/ CIRCUIT BREAKER. REFER TO

DISC/STA SCHEDULE

LCS-# 26 09 33 LIGHTING CONTROL STATION

#B#F

ELECTRICAL SYMBOL LIST

SYMBOL: TAG: SPEC

SECTION:

DESCRIPTION:

MPC-# 26 24 23 PACKAGED POWER CENTER

DEM DEM ENERGY METER26 09 13

EEM EEM EXTERNAL ENERGY METER26 09 13

PQM PQM POWER QUALITY METER26 09 13

TR-#/DTR-# 26 22 00 TRANSFORMER. REFER TO

TRANSFORMER SCHEDULE

FB-# 26 27 26 FLOOR - SERVICE FITTING

SV

SW-1P-DJ 26 09 33 SWITCH - DOOR JAMBJ

SW-OD DIMMER - WALL DIMMER

OCCUPANCY SENSORO

26 09 33

SW WALL CONTROL STATION26 09 33SW

SW-LV 26 09 33 CENTRAL CONTROL - STATIONLV

LCD SW-LCD LIGHTING CONTROL LCD STATION26 09 33

BD-# 26 25 00 BUSWAYB B B B

BP-# 26 25 00 BUSS PLUG - CIRCUIT BREAKER.

REFER TO DISC/STA SCHEDULE

BFP-# 26 25 00 BUSS PLUG - FUSIBLE DISCONNECT.

REFER TO DISC/STA SCHEDULE

BCS-# 26 25 00 BUSS PLUG - COMBINATION STARTER.

REFER TO DISC/STA SCHEDULE

BD-REC-# 26 25 00 BUSSWAY RECEPTACLE UNIT.

REFER TO DISC/STA SCHEDULE

R #

NLC SW-NLC NURSE CALL LIGHTING CONTOLLER26 09 33

ITDM ITDM IMPULSE-TOTALIZING DEMAND26 24 13

RAS 26 24 21 REMOTE ANNUNCIATOR STATIONRAS

26 32 13

LINEAR LUMINAIRES

TROFFER

WALL SCONCE LUMINAIRE

DOWNLIGHT LUMINAIRE

AIMABLE OR WALL WASH LUMINAIRE

INDUSTRIAL LUMINAIRE

POLE MOUNTED LUMINAIRE

SINGLE FACE EXIT SIGN

DOUBLE FACE EXIT SIGN

EMERGENCY UNIT

WALL BRACKET LUMINAIRE

ELECTRICAL SYMBOL LIST

SYMBOL: TAG: SPEC

SECTION:

DESCRIPTION:

WALL/CEILING EMERGENCY EXIT SIGN

REC-DUP-GFI-R 26 27 26 GROUND FAULT DEVICEG

REC-TAMP 26 27 26 DUPLEX RECEPTACLE, TAMPER RESISTANT, 125V

REC-SIM-L1630R 26 27 26 RECEPTACLE, L16-30R, 480V, 3PH

REC-FB-# 26 27 26 FLOOR BOX - POKE THRU, 125V

REC-TAMP-GFI 26 27 26 GFI DUPLEX RECEPTACLE,

TAMPER RESISTANT, 125V

REC-TAMP-QUAD 26 27 26 QUAD RECEPTACLE, TAMPER RESISTANT, 125V

REC-SIM-L2120R 26 27 26 RECEPTACLE, LOCKING L21-20R, 120/208V, 3PH

REC-SIM-L2130R 26 27 26 RECEPTACLE, LOCKING L21-30R, 120/208V, 3PH

REC-ISO-

SUR-QUAD

26 27 26 ISOLATED GROUND QUAD RECEPTACLE WITH

SURGE SUPPRESSION, 125V

REC-DUP 26 27 26 DUPLEX RECEPTACLE, 125V

REC-DUP-XP 26 27 26 DUPLEX RECEPTACLE, EXPLOSION PROOF, 125V

REC-DUP-GFI 26 27 26 DUPLEX GFI RECEPTACLE, 125V

REC-DUP-WP 26 27 26 DUPLEX GFI WEATHERPROOF RECEPTACLE 125V

W

REC-ISO 26 27 26 ISOLATED GROUND RECEPTACLE, 125V

REC-ISO-SUR 26 27 26 ISOLATED GROUND RECEPTACLE WITH SURGE

SUPPRESSION, 125V

REC-QUAD 26 27 26 QUAD RECEPTACLE, 125V

REC-QUAD-GFI 26 27 26 QUAD GFI RECEPTACLE, 125V

REC-SIM-520R 26 27 26 SIMPLEX RECEPTACLE, 125V

REC-SIM-530R 26 27 26 RECEPTACLE, 125V

REC-SIM-620R 26 27 26 RECEPTACLE, 6-20R, 250V

REC-SIM-630R 26 27 26 RECEPTACLE, 6-30R, 250V

REC-SIM-650R 26 27 26 RECEPTACLE, 6-50R, 250V

REC-SIM-720R 26 27 26 RECEPTACLE, 7-20R, 277V

REC-SIM-730R 26 27 26 RECEPTACLE, 7-30R, 277V

REC-SIM-750R 26 27 26 RECEPTACLE, 7-50R, 277V

REC-SIM-1420R 26 27 26 RECEPTACLE, 14-20R, 125/250V

REC-SIM-1430R 26 27 26 RECEPTACLE, 14-30R, 125/250V

REC-SIM-1450R 26 27 26 RECEPTACLE, 14-50R, 125/250V

REC-SIM-1460R 26 27 26 RECEPTACLE, 14-60R, 125/250V

REC-SIM-1520R 26 27 26 RECEPTACLE, 15-20R, 250V, 3PH

REC-SIM-1530R 26 27 26 RECEPTACLE, 15-30R, 250V, 3PH

REC-SIM-1550R 26 27 26 RECEPTACLE, 15-50R, 250V, 3PH

REC-SIM-XP 26 27 26 RECEPTACLE, EXPLOSION PROOF, 125V

REC-SIM-L520R 26 27 26 RECEPTACLE, LOCKING TYPE, L5-20R, 125V

REC-SIM-L530R 26 27 26 RECEPTACLE, LOCKING TYPE, L5-30R, 125V

REC-SIM-L620R 26 27 26 RECEPTACLE, LOCKING L6-20R, 250V

REC-SIM-L630R 26 27 26 RECEPTACLE, LOCKING L6-30R, 250V

REC-SIM-L720R 26 27 26 RECEPTACLE, LOCKING L7-20R, 277V

REC-SIM-L730R 26 27 26 RECEPTACLE, LOCKING L7-30R, 277V

REC-SIM-L1420R 26 27 26 RECEPTACLE, LOCKING L14-20R, 125/250V

REC-SIM-L1430R 26 27 26 RECEPTACLE, LOCKING L14-30R, 125/250V

REC-SIM-L1520R 26 27 26 RECEPTACLE, LOCKING L15-20R, 250V, 3PH

REC-SIM-L1530R 26 27 26 RECEPTACLE, LOCKING L15-30R, 250V, 3PH

ELECTRICAL SYMBOL LIST

SYMBOL: TAG: SPEC

SECTION:

DESCRIPTION:

REC-USB 26 27 26 DUPLEX RECEPTACLE, USB CHARGING

X

S

S

U

X

DUPLEX RECEPTACLE CONTROLLED BY

OCCUPANCY

O REC-DUP-O 26 27 26

REC-PED-QUAD 26 05 33 RECEPTACLE - PEDESTAL STYLE

REC-DUP-PED 26 05 33 RECEPTACLE - PEDESTAL STYLE

REC-ARC 26 27 26 ARC FAULT CIRCUIT INTERRUPTER RECEPT 125V

REC-SIM-550R 26 27 26 RECEPTACLE 125V, 50A, 125V

REC-SIM-1560R 26 27 26 RECEPTACLE, 15-60R, 250V, 3PH

REC-SIM-L1620R 26 27 26 RECEPTACLE, L16-20R, 480V, 3PH

REC-QUAD-USB 26 27 26 QUAD RECEPTACLE, USB 125V

U

REC-QUAD-WP 26 27 26 QUAD GFI WEATHERPROOF RECEPTACLE, 125V

W

REC-Z# 26 27 26 IEC PIN AND SLEEVE RECEPTACLE, 600V

PP# 26 27 23 POWER POLE

QUAD RECEPTACLE CONTROLLED BY

OCCUPANCY

O REC-QUAD-O 26 27 26

REFER TO LUMINAIRE

SCHEDULE

W/RI

RI

RI-TECH 26 05 33 TECHNOLOGY OUTLET ROUGH-IN

1. EXISTING CONDITIONS ARE SHOWN BASED ON INFORMATION OBTAINED FROM FIELD

SURVEYS, EXISTING BUILDING DOCUMENTS, AND STAFF. VERIFY EXISTING CONDITIONS AND

REPORT ANY CONFLICTS BEFORE PROCEEDING.

2. NOT ALL EXISTING EQUIPMENT, LUMINAIRES, AND CONDUIT ARE SHOWN. VERIFY EXISTING

CONDITIONS AND REPORT ANY CONFLICTS WITH NEW WORK BEFORE STARTING WORK.

3. FIELD VERIFY THE AVAILABLE CLEARANCES FOR CABLE TRAY, BUSWAY AND CONDUITS

BEFORE FABRICATION. RISES AND DROPS MAY BE NECESSARY BECAUSE OF EXISTING

FIELD CONDITIONS

4. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR CUTTING, REMOVAL AND PATCHING OF

ROOFS, WALLS, AND FLOORS ASSOCIATED WITH WORK BY ALL CONTRACTORS.

CONTRACTORS SHALL NOTIFY THE GC OF AFFECTED AREAS PRIOR TO BIDDING

5. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR REMOVAL AND REPLACEMENT OF

CEILINGS, CEILING TILES, AND CEILING GRIDS ASSOCIATED WITH AREAS OF WORK BY ALL

CONTRACTORS. NOTIFY THE GENERAL CONTRACTOR OF AFFECTED AREAS PRIOR TO

BIDDING.

6. WHERE EXISTING ELECTRICAL SYSTEMS ARE LOCATED IN AREAS THAT CONFLICT WITH NEW

EQUIPMENT, PIPING, OR DUCTWORK TO BE INSTALLED, EACH CONTRACTOR SHALL EITHER

ARRANGE NEW EQUIPMENT, CONDUIT, OR DUCTWORK IN SUCH A FASHION THAT IT DOES

NOT CONFLICT WITH EXISTING SYSTEMS, OR REWORK EXISTING ELECTRICAL SYSTEMS TO

ALLOW FOR INSTALLATION OF NEW EQUIPMENT, PIPING, OR DUCTWORK.

ELECTRICAL RENOVATION NOTES:

THESE NOTES APPLY TO ALL ELECTRICAL SHEETS AND TRADES, INCLUDING BUT NOT LIMITED

TO, LIGHTING, POWER, AND SYSTEMS.

ELECTRICAL PHASING NOTES:

THESE NOTES APPLY TO ALL ELECTRICAL SHEETS AND TRADES, INCLUDING BUT NOT LIMITED

TO, LIGHTING, POWER, AND SYSTEMS.

1. REFER TO [ARCHITECTURAL] DRAWINGS FOR GENERAL DESCRIPTION OF PHASES. REFER

TO [CONSTRUCTION MANAGER'S/GENERAL CONTRACTOR'S/ARCHITECT'S] INSTRUCTIONS

FOR MORE DETAILS, PHASING SCHEDULES AND FOR CONCURRENT WORK. MECHANICAL,

ELECTRICAL AND TECHNOLOGY DRAWINGS DEPICT THE INTENT OF THE FINAL DESIGN. THE

MECHANICAL, ELECTRICAL, AND TECHNOLOGY DRAWINGS DO NOT DEPICT THE MEANS AND

METHODS TO MEET THE REQUIREMENTS OF THE PHASING CRITERIA.

2. REVIEW PROJECT PHASING PLANS TO COORDINATE DEMOLITION WORK, OUTAGES, ETC.

WITH AFFECTED ADJACENT AREAS.

3. PROVIDE TEMPORARY LIGHTING, POWER, SYSTEMS, ETC. AS NEEDED TO MAINTAIN

SERVICE TO ALL AREAS DURING ALL PHASES OF PROJECT.

4. INSTALL TEMPORARY LIGHTING, CIRCUITS, ETC. AS NECESSARY TO KEEP ALL OCCUPIED

SPACES OPERATIONAL THROUGHOUT ALL PHASES OF THE PROJECT

5. PHASE DEMOLITION WORK TO MINIMIZE DOWNTIME.

PLAN OR DETAIL NUMBER

PLAN OR DETAIL NAME

PLAN OR DETAIL SCALE

DETAIL REFERRED TO BY SECTION CUT

SHEET DETAIL IS LOCATED ON

NAME

VIEW NAME

1/8" = 1'-0"

M101

T101

SIM

DETAIL REFERRED TO BY ELEVATION

SHEET DETAIL IS LOCATED ON

INDICATES SIMILAR DETAIL

REFERENCED IN MULTIPLE LOCATIONS

SIM

INDICATES SIMILAR DETAIL

REFERENCED IN MULTIPLE LOCATIONS

LEVEL NAME

10' - 0" HEIGHT ABOVE

PROJECT 0' - 0"

1 INDICATES NOTE USED TO DESCRIBE

ADDITIONAL INFORMATION ABOUT

WORK REQUIRED, SPECIFIC TO THE

SHEET AND/OR DETAIL

N O R

HT

INDICATES DIRECTION OF TRUE NORTH

VIEW KEY

NEW WORK BY THIS CONTRACTOR

(DARK SOLID LINE)

NEW WORK UNDERFLOOR OR UNDERGROUND BY THIS CONTRACTOR

(DARK LONG DASHED LINE)

NEW WORK BY OTHERS AND/OR EXISTING TO REMAIN

(LIGHT SOLID LINE)

EXISTING TO BE REMOVED BY THIS CONTRACTOR

(DARK SHORT DASHED LINE)

'TAG'-E TAGS WITH DASH 'E' INDICATES THE REFERENCED OBJECT IS EXISTING

TAG-1 UNDERLINED TEXT INDICATES ADDITIONAL INFORMATION CAN BE FOUND

ELSEWHERE IN A SCHEDULE, MATERIAL LIST, OR SYMBOL LIST

LINE TYPE AND TAG KEY:

1. ##-### INDICATES ELECTRICAL EQUIPMENT DEFINED IN ELECTRICAL SCHEDULES OR

SPECIFICATION. REFER TO DRAWINGS CONTAINING ELECTRICAL SCHEDULES. PERMANENT

NAMEPLATE SHALL MATCH FINAL EQUIPMENT NOMENCLATURE, NOT ELECTRICAL

EQUIPMENT TAG NAME, REFER TO SPECIFICATIONS.

ELECTRICAL MOUNTING SUBSCRIPT KEY:

A MOUNT AT +6" TO CENTERLINE ABOVE COUNTER OR BACKSPLASH

C MOUNT AT CEILING

H MOUNT ORIENTED HORIZONTALLY

L MOUNT IN CASEWORK

M MOUNT IN MODULAR FURNITURE

R MOUNT IN SURFACE RACEWAY

EWC ELECTRIC WATER COOLER

ELECTRICAL GENERAL NOTES:

LUMINAIRE

F1 = FIXTURE TAG

1 = CIRCUIT NUMBER

a = SWITCH DESIGNATION

NL = SUBSCRIPT (IF APPLICABLE)

Z = ZONE DESIGNATION

*IF LABEL IS ORIENTED HORIZONTALLY A SLASH WILL SEPARATE THIS

INFORMATION. EX: F1 / 1 / a / NL

DEVICE

A = MOUNTING (IF APPLICABLE)

1 = CIRCUIT NUMBER

*IF LABEL IS ORIENTED HORIZONTALLY A SLASH WILL SEPARATE THIS

INFORMATION. EX: A / 1

LUMINAIRE KEY:

DEVICE KEY:

ELECTRICAL SHEET INDEX

11-E-100 FIRST FLOOR PLAN ELECTRICAL - BUILDINGS 11, 16, & 19

11-ED-100 FIRST FLOOR PLAN ELECTRICAL - DEMOLITION - BUILDINGS 11, 16, & 19

E-100 ELECTRICAL COVERSHEET

E-300 ELECTRICAL DETAILS

GRAND TOTAL: 4

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMP

321 4 5 6 7 8 9 10

Calvin rchitects, P.C.L 3705 North 200th Street

Elkhorn, Nebraska 68022

Phone: 402.291.6941 Fax: 402.291.9193

AH. INZ

Shaffer & Stevens 9910 North 48th Street

Omaha, Nebraska68152

Phone: 402.455.7698 Fax: 402.455.7597

504-18-119

AMI Environmental Inc

8802 S 135th Street

Omaha, NE 68138

Phone:(402) 397-5001

IMEG Corp.

14755 Preston Rd., Suite 845

Dallas, TX 75254

Phone:(972) 239-6100

15% Design Submission 07/14/2020

20% Design Submission

30% Design Submission

35%/SD1 Schematic Design Submission

09/08/2020

08/14/2020

11/17/2020

C R e v it L o c a l F ile s \M

E

.0

A m a ri llo

B o ile r

R e p la c e m e n t_ C

S c o tt .R

.K o c ia n .r v t

/1 /2

:4

:0

P M

E-100

ELECTRICAL COVERSHEET

November 17, 2020

Replace Boilers and PipingSD-1 35% SUBMITTAL -

REQUEST FOR PROPOSAL

Thomas E. Creek VAMC-Amarillo, TX

REFERENCE SCALE IN INCHES

0 1 2 3

PROJECT #

IMEG CORP RESERVES PROPRIETARY RIGHTS, INCLUDING COPYRIGHTS, TO THIS

DRAWING AND THE DATA SHOWN THEREON. SAID DRAWING AND/OR DATA ARE

THE EXCLUSIVE PROPERTY OF IMEG CORP AND SHALL NOT BE USED OR

REPRODUCED FOR ANY OTHER PROJECT WITHOUT THE EXPRESS WRITTEN

APPROVAL AND PARTICIPATION OF IMEG CORP. © 2020 IMEG CORP.

14755 PRESTON ROAD, SUITE 845

DALLAS, TX 75254

972.239.6100 FAX: 972.239.6102

www.imegcorp.com

TBPE# F-18632

20001967.00

Revisions: Date:

FOR REFERENCE

ONLY NOT FOR

CONSTRUCTION

B-2 B-3B-1

1 1 1

2.2

C K M N

4A

A

2.7

B

GD E F

3.5

L

2.2

H

1A

JC1

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMP

321 4 5 6 7 8 9 10

Calvin rchitects, P.C.L 3705 North 200th Street

Elkhorn, Nebraska 68022

Phone: 402.291.6941 Fax: 402.291.9193

AH. INZ

Shaffer & Stevens 9910 North 48th Street

Omaha, Nebraska68152

Phone: 402.455.7698 Fax: 402.455.7597

504-18-119

AMI Environmental Inc

8802 S 135th Street

Omaha, NE 68138

Phone:(402) 397-5001

IMEG Corp.

14755 Preston Rd., Suite 845

Dallas, TX 75254

Phone:(972) 239-6100

15% Design Submission 07/14/2020

20% Design Submission

30% Design Submission

35%/SD1 Schematic Design Submission

09/08/2020

08/14/2020

11/17/2020

C R e v it L o c a l F ile s \M

E

.0

A m a ri llo

B o ile r

R e p la c e m e n t_ C

S c o tt .R

.K o c ia n .r v t

/1 /2

:4

:0

P M

11-ED-100

FIRST FLOOR PLAN ELECTRICAL -

DEMOLITION - BUILDINGS 11, 16, & 19

November 17, 2020

Replace Boilers and PipingSD-1 35% SUBMITTAL -

REQUEST FOR PROPOSAL

Thomas E. Creek VAMC-Amarillo, TX

N O R

HT

1/8" = 1'-0"

FIRST FLOOR DEMOLITION - ELECTRICAL

REFERENCE SCALE IN INCHES

0 1 2 3

PROJECT #

IMEG CORP RESERVES PROPRIETARY RIGHTS, INCLUDING COPYRIGHTS, TO THIS

DRAWING AND THE DATA SHOWN THEREON. SAID DRAWING AND/OR DATA ARE

THE EXCLUSIVE PROPERTY OF IMEG CORP AND SHALL NOT BE USED OR

REPRODUCED FOR ANY OTHER PROJECT WITHOUT THE EXPRESS WRITTEN

APPROVAL AND PARTICIPATION OF IMEG CORP. © 2020 IMEG CORP.

14755 PRESTON ROAD, SUITE 845

DALLAS, TX 75254

972.239.6100 FAX: 972.239.6102

www.imegcorp.com

TBPE# F-18632

20001967.00

GENERAL NOTES:

1. THE INFORMATION ON THE DEMOLITION

DRAWINGS ARE FROM DOCUMENTS PROVIDED

TO THE ENGINEER. CONTRACTOR WILL BE

RESPONSIBLE FOR VISITING THE SITE PRIOR

TO SUBMITTING A BID TO DETERMINE THE

AMOUNT OF DEMOLITION THAT WILL BE

REQUIRED. CONTRACTOR SHALL EXAMINE THE

EXISTING BUILDING AND GENERALLY VERIFY

THE LOCATION OF ALL EXISTING WORK AND

BECOME INFORMED AS TO THE RELATION TO

AND EFFECT ON, THE WORK REQUIRED

BEFORE SUBMITTING A BID. SUBMISSION OF A

BID WILL CONSTITUTE EVIDENCE THAT THE

CONTRACTOR HAS INSPECTED THE SITE OF

THE PROPOSED WORK. DEVICES ON EXISTING

WALLS TO REMAIN OR TO BE REMOVED MAY

NOT APPEAR ON DRAWINGS DUE TO EXISTING

FURNITURE, BOOKCASES, EQUIPMENT, ETC.

BLOCKING VIEW DURING SITE VISIT.

2. CONTRACTOR SHALL STUDY ALL PLANS AND

UNDERSTAND THE FULL SCOPE OF

CONSTRUCTION PRIOR TO BIDS AND

BEGINNING ANY WORK. CONTRACTOR SHALL

UNDERSTAND THAT THE BUILDING WILL BE

RENOVATED IN PHASES AND THAT

ELECTRICAL EQUIPMENT SERVING THOSE

ARES THAT WILL BE RENOVATED IN LATER

PHASES SHALL BE RECONNECTED AND RE-

ENERGIZED TO MAINTAIN POWER TO THOSE

AREAS IF DISRUPTED DURING PHASED

CONSTRUCTION. CONTRACTOR SHALL

UNDERSTAND THAT THE ELECTRICAL

EQUIPMENT SERVING PORTIONS OF THE

BUILDING THAT ARE OUTSIDE OF THIS

PROJECT’S SCOPE SHALL REMAIN AND BE

RECONNECTED AND RE-ENERGIZED TO

MAINTAIN POWER TO HOSE AREAS IF

DISRUPTED DURING PHASED CONSTRUCTION.

3. COORDINATE DEMOLITION WORK WITH THE

BUILDING MAINTENANCE PERSONNEL AND

OTHER TRADES PERFORMING WORK IN THE

BUILDING PRIOR TO THE REMOVAL OF ANY

ITEMS OF EQUIPMENT OR SYSTEMS THAT WILL

AFFECT OTHER SYSTEMS WITHIN THE LIMIT OF

NEW CONSTRUCTION OR OTHER AREAS OF

THE BUILDING. CONTRACTOR SHALL VERIFY

WITH THE OWNER IF THE BUILDING WILL BE

OCCUPIED DURING CONSTRUCTION, AND

THEREFORE UTILITIES MUST REMAIN IN

OPERATION AT ALL TIMES. ANY REQUIRED

OUTAGES MUST BE COORDINATED WITH THE

OWNER.

4. PRIOR TO THE REMOVAL OF ANY EQUIPMENT,

CONTRACTOR MUST VERIFY THE ORIGIN AND

TERMINATION OF THOSE SYSTEMS AND

CONFIRM THAT THE ITEMS BEING REMOVED

DO NOT SERVE ANY ITEMS THAT ARE TO

REMAIN DOWN/UP STREAM (INCLUDING THOSE

IN AREAS OUTSIDE THE CONTRACTOR LIMITS).

IF REMOVAL OF ANY ITEMS DOES DISRUPT

OTHER SYSTEMS DOWN/UP STREAM,

CONTRACTOR SHALL EXTEND, RECONNECT TO

NEW OR RELOCATED EQUIPMENT, AND

MAINTAIN FULL FUNCTIONALITY OF SYSTEM.

5. REFER TO HVAC & PLUMBING DRAWINGS FOR

OTHER DEMOLITION INFORMATION.

DISCONNECT AND REMOVE ALL WIRE,

CONDUIT, AND DISCONNECT SWITCHES

SERVING EQUIPMENT TO BE REMOVED AND

LABEL CIRCUIT BREAKER ‘SPARE’

KEYNOTES:

1. EXISTING BOILER AND BOILER CONTROLS TO

BE DEMOLISHED. DISCONNECT AND REMOVE

ALL ASSOCIATED WIRE AND CONDUIT BACK TO

MOTOR CONTROL PANEL.

2. ADD ALTERNATE : EXISTING 155KW

GENERATOR, ASSOCIATED WIRE AND CONDUIT

TO BE DISCONNECTED AND REMOVED.

3. ADD ALTERNATE : EXISTING GENERATOR

ANNUNCIATOR PANEL, ALL ASSOCIATED

WIRING AND CONDUIT TO BE DISCONNECTED

AND REMOVED.

4. ADD ALTERNATE : EXISTING GENERATOR

CIRCUIT BREAKER TO BE DISCONNECTED AND

REMOVED.

Revisions: Date:

FOR REFERENCE

B-02 B-01B-03

1 1 1

BOILER HOUSE MCC

EXISTING ATS

2 2 2

2.2

C K M N

4A

A

2.7

B

GD E F

3.5

L

2.2

H

1A

JC1

NO SCALE2

EXISTING BOILER HOUSE MCC

NO SCALE3

PANEL 'L12' SPARE BREAKERS

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMP

321 4 5 6 7 8 9 10

Calvin rchitects, P.C.L 3705 North 200th Street

Elkhorn, Nebraska 68022

Phone: 402.291.6941 Fax: 402.291.9193

AH. INZ

Shaffer & Stevens 9910 North 48th Street

Omaha, Nebraska68152

Phone: 402.455.7698 Fax: 402.455.7597

504-18-119

AMI Environmental Inc

8802 S 135th Street

Omaha, NE 68138

Phone:(402) 397-5001

IMEG Corp.

14755 Preston Rd., Suite 845

Dallas, TX 75254

Phone:(972) 239-6100

15% Design Submission 07/14/2020

20% Design Submission

30% Design Submission

35%/SD1 Schematic Design Submission

09/08/2020

08/14/2020

11/17/2020

C R e v it L o c a l F ile s \M

E

.0

A m a ri llo

B o ile r

R e p la c e m e n t_ C

S c o tt .R

.K o c ia n .r v t

/1 /2

:3

:1

P M

11-E-100

FIRST FLOOR PLAN ELECTRICAL -

BUILDINGS 11, 16, & 19

November 17, 2020

Replace Boilers and PipingSD-1 35% SUBMITTAL -

REQUEST FOR PROPOSAL

Thomas E. Creek VAMC-Amarillo, TX

N O R

HT

1/8" = 1'-0"

FIRST FLOOR PLAN - ELECTRICAL

REFERENCE SCALE IN INCHES

0 1 2 3

PROJECT #

IMEG CORP RESERVES PROPRIETARY RIGHTS, INCLUDING COPYRIGHTS, TO THIS

DRAWING AND THE DATA SHOWN THEREON. SAID DRAWING AND/OR DATA ARE

THE EXCLUSIVE PROPERTY OF IMEG CORP AND SHALL NOT BE USED OR

REPRODUCED FOR ANY OTHER PROJECT WITHOUT THE EXPRESS WRITTEN

APPROVAL AND PARTICIPATION OF IMEG CORP. © 2020 IMEG CORP.

14755 PRESTON ROAD, SUITE 845

DALLAS, TX 75254

972.239.6100 FAX: 972.239.6102

www.imegcorp.com

TBPE# F-18632

20001967.00

KEYNOTES:

1. NEW 250BHP BOILER. CONNECT NEW BOILER

TO NEW OVERCURRENT PROTECTION DEVICE

(MATCH EXISTING) IN EXISTING BOILER HOUSE

MOTOR CONTROL CENTER IN SPACE MADE

AVAILABLE THROUGH DEMOLITION OF

EXISTING BOILER.

2. NEW BOILER CONTROLS. CONNECT EACH

BOILER CONTROL PANEL TO DEDICATED

SPARE 20A/1P CIRCUIT BREAKER IN PANEL

'LIGHTING PANELBOARD L12' LOCATED INSIDE

BOILER HOUSE MCC. VERIFY EXACT LOCATION

PRIOR TO ROUGH IN. REFER TO DETAIL 1/E300

FOR MOUNTING INFORMATION.

3. ADD ALTERNATE : NEW 155KW GENERATOR.

CONNECT TO EXISTING AUTOMATIC TRANSFER

SWITCH.

4. ADD ALTERNATE : NEW GENERATOR

ANNUNCIATOR PANEL.

Revisions: Date:

FOR REFERENCE

ONLY NOT FOR

CONTROL PANEL

UNI STRUT SUPPORT

EMBEDDED

CONCRETE BASE

4" CONCRETE BASE

FINISHED FLOOR

TO BUILDING 4 SWITCHBOARD

EXISTING 400A MLO PANEL 'M'

100 300

TO PANEL 'H-19'

BOILER HOUSE METER

M

EXISTING ATS

EXISTING BOILER HOUSE MCC

EXISTING 250A GENERATOR

CIRCUIT BREAKER

EXISTING 155KW GENERATOR

MAIN BREAKER

BOILER 1

BOILER 3

BOILER 2

PANELBOARD L11

PANELBOARD L12

PANELBOARD H11

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMP

321 4 5 6 7 8 9 10

Calvin rchitects, P.C.L 3705 North 200th Street

Elkhorn, Nebraska 68022

Phone: 402.291.6941 Fax: 402.291.9193

AH. INZ

Shaffer & Stevens 9910 North 48th Street

Omaha, Nebraska68152

Phone: 402.455.7698 Fax: 402.455.7597

504-18-119

AMI Environmental Inc

8802 S 135th Street

Omaha, NE 68138

Phone:(402) 397-5001

IMEG Corp.

14755 Preston Rd., Suite 845

Dallas, TX 75254

Phone:(972) 239-6100

15% Design Submission 07/14/2020

20% Design Submission

30% Design Submission

35%/SD1 Schematic Design Submission

09/08/2020

08/14/2020

11/17/2020

C R e v it L o c a l F ile s \M

E

.0

A m a ri llo

B o ile r

R e p la c e m e n t_ C

S c o tt .R

.K o c ia n .r v t

/1 /2

:4

:0

P M

E-300

ELECTRICAL DETAILS

November 17, 2020

Replace Boilers and PipingSD-1 35% SUBMITTAL -

REQUEST FOR PROPOSAL

Thomas E. Creek VAMC-Amarillo, TX

REFERENCE SCALE IN INCHES

0 1 2 3

PROJECT #

IMEG CORP RESERVES PROPRIETARY RIGHTS, INCLUDING COPYRIGHTS, TO THIS

DRAWING AND THE DATA SHOWN THEREON. SAID DRAWING AND/OR DATA ARE

THE EXCLUSIVE PROPERTY OF IMEG CORP AND SHALL NOT BE USED OR

REPRODUCED FOR ANY OTHER PROJECT WITHOUT THE EXPRESS WRITTEN

APPROVAL AND PARTICIPATION OF IMEG CORP. © 2020 IMEG CORP.

14755 PRESTON ROAD, SUITE 845

DALLAS, TX 75254

972.239.6100 FAX: 972.239.6102

www.imegcorp.com

TBPE# F-18632

20001967.00

NO SCALE

CONTROL PANEL MOUNTING DETAIL

NO SCALE

PARTIAL EXISTING ELECTRICAL ONE LINE DIAGRAM

Revisions: Date:

FOR REFERENCE