1686626dwg11of14_ELECTRICAL.pdf

POWER PANELBOARDS & EQUIPMENT

SD

PANELBOARD, SURFACE MOUNTED AT 72" AFF TO TOP. SEE PANELBOARD

SCHEDULE.

PANELBOARD, FLUSH MOUNTED AT 72" AFF TO TOP. SEE PANELBOARD

SCHEDULE.

DISTRIBUTION PANELBOARD, SURFACE MOUNTED AT 72" AFF TO TOP. SEE

PANELBOARD SCHEDULE.

- TYPICAL LIGHTING APPLIANCE PANELBOARD NAMING SCHEME -

N21C3

FIRST EQ - EQUIPMENT BRANCH OF ESSENTIAL POWER SYSTEM

POSITION (1-2 (EMERGENCY)

CHARACTERS) LS - LIFE SAFETY BRANCH OF ESSENTIAL POWER SYSTEM

(EMERGENCY)

N - NORMAL POWER SYSTEM

SECOND POSITION 4 - 480Y/277 VOLT

(1-3 CHARACTERS) 2 - 208Y/120 VOLT

COM - COMMUNICATIONS PANEL, 208Y/120V

THIRD POSITION 1 - FIRST FLOOR

(1 CHARACTER) 2 - SECOND FLOOR

FOURTH POSITION A - ELECTRICAL ROOM 'A'

(1 CHARACTER) B - ELECTRICAL ROOM 'B'

FIFTH POSITION 1 - PANEL #1

(1 CHARACTER) 2 - PANEL #2

3 - PANEL #3

- TYPICAL DISTRIBUTION PANELBOARD NAMING SCHEME -

DP-480-EQ

FIRST

POSITION (2 DP - DISTRIBUTION PANELBOARD

CHARACTERS)

SECOND POSITION 480 - 480Y/277 VOLT

(3 CHARACTERS) 208 - 208Y/120 VOLT

THIRD POSITION EQ - EQUIPMENT BRANCH OF ESSENTIAL POWER SYSTEM

(1-3 CHARACTERS) (EMERGENCY)

LS - LIFE SAFETY BRANCH OF ESSENTIAL POWER SYSTEM

(EMERGENCY)

N - NORMAL POWER SYSTEM

1B - ELECTRIC ROOM '1B'

- MISCELLANEOUS PANELBOARD NAMING SCHEME -

4HVAC1 - 480Y/277V HVAC PANEL

2HVAC1 - 208Y/120V HVAC PANEL

4STER - 480Y/277V STERILIZATION SUITE PANEL

4DENT - 480Y/277V DENTAL EQUIPMENT PANEL

DISCONNECT SWITCH, FUSIBLE, IF DISCONNECT SIZE AND FUSING IS NOT

SHOWN ON PLAN, REFER TO POWER SINGLE LINE DIAGRAM ON SHEETS EP6xx THRU EP6xx.

FUSE SIZE (FM - FUSE PER MANUFACTURER'S RECOMMENDATION; NF - NON

FUSED)

DISCONNECT AMP RATING

# OF POLES

SAME AS ABOVE EXCEPT MOUNTED ON UNISTRUT STAND.

INTEGRAL SAFETY DISCONNECT SWITCH FURNISHED WITH EQUIPMENT. IF

EQUIPMENT IS SHOWN WITH DISCONNECT BUT MANUFACTURER DOES NOT

PROVIDE ONE, CONTRACTOR IS RESPONSIBLE FOR PROVIDING DISCONNECT

OF REQUIRED SIZE AND TYPE. COORDINATE WITH APPROPRIATE TRADE

INVOLVED.

DRY TYPE TRANSFORMER. PARAMETERS AS SHOWN ON PLANS. NAMING

SCHEME FOLLOWS PANELBOARD TYPICAL NAMING SCHEMES.

LIGHTING INVERTER. SEE SINGLE LINE DIAGRAM FOR ELECTRICAL

CHARACTERISTICS.

SURGE PROTECTIVE DEVICE. SEE SPECIFICATIONS.

ELECTRIC METER.

ENCLOSED CIRCUIT BREAKER. SURFACE MOUNTED UON.

GENERATOR SET REMOTE ALARM PANEL.

T-XXX

LI-X

T

SPD

M

B

GAP

N21A:1,3,5

BRANCH CIRCUITS

1"

10'S

INDICATES CONCEALED OVERHEAD OR IN WALLS.

INDICATES CONCEALED IN OR BELOW FLOOR SLAB OR BELOW ROOF. SEE

SPECIFICATIONS FOR RESTRICTIONS. CONDUIT BELOW SLAB ON GRADE

MUST BE PVC COATED RIGID CONDUIT.

INDICATES EXPOSED CONDUIT.

CONDUIT TERMINATION, (C) CAPPED, (B) BUSHED, (G) GROUND BUSHING.

BRANCH CIRCUIT WIRING IN CONDUIT. TICK MARKS INDICATE THE NUMBER

OF #12 AWG PHASE & NEUTRAL CONDUCTORS IN 3/4" CONDUIT UNLESS

OTHERWISE NOTED. PROVIDE A #12 AWG GROUND CONDUCTOR IN ALL

CONDUIT UON. ARROWHEADS INDICATES NUMBER OF CIRCUITS UP TO

THAT POINT (DEVICE, LUMINAIRE, ETC.). EXAMPLE SHOWN, ONE

ARROWHEAD/CIRCUIT TO RECEPTACLE.

HOMERUN TO PANELBOARD. PANELBOARD AND CIRCUIT DESIGNATIONS AS

INDICATED.

INDICATES SIZE OF CONDUIT OTHER THAN 3/4". 1" CONDUIT SHOWN HERE.

INDICATES SIZE OF ALL CIRCUIT CONDUCTORS INCLUDING GROUND IF

OTHER THAN #12 AWG. SHOWN, #10 AWG CONDUCTORS.

GENERAL RECEPTACLES

SUBSCRIPT MODIFIER LEGEND FOR BASIC RECEPTACLE TYPES:

NOTE: VERIFY WITH CONTRACTING OFFICER THE HEIGHT OF ALL COUNTER

TOPS, BACKSPLASHES, TABLE TOPS OR SINKS WHICH AFFECT THE MOUNTING

HEIGHT OF RECEPTACLES. MOUNTING HEIGHTS GIVEN ARE TO CENTER OF

DEVICE BOX UON.

CRG - TAMPER RESISTANT GFI RECEPTACLE MOUNTED 4" ABOVE COUNTER

TOP, BACKSPLASH OR SINK.

CT - RECEPTACLE MOUNTED 4" ABOVE COUNTER TOP, BACKSPLASH OR

TABLE TOP.

CTG - GFI RECEPTACLE MOUNTED 4" ABOVE COUNTER TOP, BACKSPLASH

OR SINK.

CTR - SAFETY TYPE, TAMPER RESISTANCE RECEPTACLE MOUNTED 4") ABOVE

COUNTER TOP OR BACKSPLASH.

CW - RECEPTACLE MOUNTED IN CASEWORK 4" ABOVE COUNTER TOP UON.

EWC - GFI RECEPTACLE FOR ELECTRIC WATER COOLER. COORDINATE

LOCATION AND HEIGHT WITH PLUMBING. REFER TO GENERAL NOTE 24.

GFI - GROUND FAULT INTERRUPTER TYPE RECEPTACLE.

HG - HOSPITAL GRADE RECEPTACLE.

HGC - HOSPITAL GRADE RECEPTACLE MOUNTED 4" ABOVE COUNTER TOP OR

BACKSPLASH.

HGG - GFI TYPE, HOSPITAL GRADE RECEPTACLE MOUNTED 4" ABOVE

COUNTER TOP OR BACKSPLASH.

SR - SAFETY TYPE, TAMPER RESISTANT RECEPTACLE.

SRG - SAFETY TYPE, TAMPER RESISTANT GFI.

SW - RECEPTACLE SWITCHED BY AUTOMATIC MEANS. MARK RECEPTACLE

PER NFPA 70, 406.3(E).

TVF - RECEPTACLE FOR FLAT SCREEN TV. COORDINATE MOUNTING HEIGHTS

OF RECEPTACLES AND ASSOCIATED DATA OUTLETS WITH BLOCKING IN

WALL AS WELL AS WITH TV BRACKET LOCATION. REFER TO

ARCHITECTURAL DETAILS FOR ADDITIONAL INFORMATION.

WP - WATER AND/OR WEATHER RESISTANT.

WPG - WEATHER RESISTANT GFI RECEPTACLE WITH WEATHERPROOF "IN USE"

COVER.

WTG - WEATHER RESISTANT & TAMPER RESISTANT GFI RECEPTACLE WITH

WEATHERPROOF "IN USE" COVER.

SIMPLEX RECEPTACLE, 20A, 125V, 2P-3 WIRE, NEMA 5-20R.

DUPLEX RECEPTACLE, 20A, 125V, 2P-3 WIRE, NEMA 5-20R.

DUPLEX RECEPTACLE, 20A, 125V, 2P-3 WIRE, NEMA 5-20R, SWITCHED BY

AUTOMATIC MEANS. RECEPTACLE MUST BE MARKED PER NFPA 70. SEE DETAIL

A1/EP502.

STUB-UP THRU FLOOR WITH DIE CAST FSD BOX MOUNTED 6" ABOVE FLOOR WITH

DUPLEX RECEPTACLE, 20A, 125V, 2P-3 WIRE, NEMA 5-20R.

DOUBLE DUPLEX RECEPTACLE, 20A, 125V, 2P-3 WIRE, NEMA 5-20R.

EMERGENCY DUPLEX RECEPTACLE, 20A, 125V, 2P-3 WIRE, NEMA 5-20R (RED

COLOR). SEE DETAIL A2/EP502.

EMERGENCY DOUBLE DUPLEX RECEPT, 20A, 125V, 2P-3 WIRE, NEMA 5-20R (RED

COLOR).

DUPLEX RECEPTACLE, CEILING MOUNTED, RECESSED, SUPPORT FROM CEILING

SUSPENSION SYSTEM, 20A, 125V, 2P-3 WIRE, NEMA 5-20R.

DUAL CHANNEL, SURFACE METAL RACEWAY AS SPECIFIED. TOP CHANNEL FOR

VOICE/DATA OUTLETS, AND BOTTOM CHANNEL FOR POWER RECEPTACLES.

MOUNT 4" ABOVE COUNTERTOP OR BACKSPLASH, UNLESS OTHERWISE NOTED.

LOCATE RECEPTACLES AT 18" ON CENTER.

X

X

SPECIAL RECEPTACLES

SPECIAL SIMPLEX RECEPTACLE - NEMA CONFIGURATION GIVEN BY SUBSCRIPT

'X', WHERE 'X' EQUALS ONE OF THE LETTERS BELOW. NEMA CONFIGURATION

SHOWN ON PLANS ARE FOR BID PURPOSES ONLY. ACTUAL NEMA

CONFIGURATION REQUIRED IN EACH CASE MAY VARY DEPENDING UPON

SPECIFIC MANUFACTURER OF EQUIPMENT BEING SUPPLIED. VERIFY NEMA

CONFIGURATION WITH CONTRACTING OFFICER AND/OR MANUFACTURER.

SPECIAL RECEPTACLE (EMERGENCY POWER).

NEMA CONFIGURATION SUBSCRIPT LEGEND:

NOTE: SUBSCRIPT MODIFIER LEGEND FOR BASIC RECEPTACLE TYPES MAY ALSO BE

APPLIED TO SPECIAL RECEPTACLES.

A - 125V, 30A, 1Ø (NEMA 5-30R)

B - 125V, 30A, 1Ø (NEMA L5-30R) LOCKING RECEPTACLE

C - 208V, 15A, 1Ø (NEMA 6-15R)

D - 208V, 20A, 3Ø (NEMA L15-20R) LOCKING RECEPTACLE

E - 208V, 20A, 1Ø (NEMA 6-20R)

F - 208V, 20A, 1Ø (NEMA L6-20R) LOCKING RECEPTACLE

G - 208V, 20A, 1Ø (NEMA 14-20R)

H - 208V, 20A, 3Ø (NEMA L21-20R) LOCKING RECEPTACLE

J - 208V, 30A, 1Ø (NEMA 6-30R)

K - 208V, 30A, 1Ø (NEMA L6-30R) LOCKING RECEPTACLE

L - 208V, 40A, 1Ø (NEMA 6-50R) ON 40A/2P CIRCUIT BREAKER

M - 208V, 50A, 1Ø (NEMA 14-50R)

N - 208V, 50A, 1Ø (NEMA L14-50R) LOCKING RECEPTACLE

P - 208V, 50A, 3Ø (NEMA 15-50R)

Q - 208V, 60A, 1Ø (NEMA L14-60R) LOCKING RECEPTACLE

S - 125V, 20A, 1Ø (NEMA L5-20R) LOCKING RECEPTACLE

J

J

J

J

WP

MF

JUNCTION BOXES

JUNCTION BOX IN OR ABOVE CEILING.

WEATHERPROOF DIE CAST BOX WITH WEATHERPROOF COVER.

JUNCTION BOX IN WALL - MOUNT AT 18" AFF UNLESS OTHERWISE NOTED.

SAME AS ABOVE EXCEPT WITH FLEXIBLE CONNECTION TO EQUIPMENT. CL =

MOUNTED ABOVE CEILING. MF = MODULAR FURNITURE, PRE-WIRED

(COORDINATE WITH MANUFACTURER SO THAT THE FURNITURE CONNECTOR

WIRING MATCHES THE NUMBER OF BRANCH CIRCUITS BEING PROVIDED AT THE

JUNCTION BOX). SEE DETAIL C4/EP502.

BLANK (NON-RECEPTACLE TYPE) GFCI MODULE, 125VAC, 20A, HEAVY DUTY FOR

PROVIDING GFCI PROTECTION FOR RECEPTACLE WHICH IS NOT READILY

ACCESSIBLE. ROUTE BRANCH CIRCUIT THRU GFCI DEVICE. MOUNT 18"AFF

UNLESS OTHERWISE NOTED. PROVIDE MICARTA LABEL WITH 1/4" HIGH BLACK

LETTERS ON WHITE BACKGROUND AND MOUNT ABOVE THE FACE PLATE.

LETTERING MUST READ 'GFCI PROTECTION FOR (EQUIPMENT NAME)". EXAMPLE -

GFCI PROTECTION FOR ELECTRIC WATER COOLER. BASIS OF DESIGN = HUBBELL

#813R516 OR APPROVED EQUAL.

J

GFCI

CONTROLS & MECHANICAL EQUIPMENT

M

VFD

COMBINATION DISCONNECT & MOTOR CONTROLLER (STARTER). WITH NO

SUBSCRIPT, PROVIDE MAGNETIC TYPE WITH THERMAL OVERLOAD PROTECTION.

"VFD" SUBSCRIPT INDICATES VARIABLE FREQUENCY DRIVE (AKA ADJUSTABLE

SPEED DRIVE) WITH INTEGRAL DISCONNECTING MEANS. COORDINATE EXACT

LOCATION WITH MECHANICAL. FOR ALL HVAC EQUIPMENT: REFER TO GENERAL

NOTES. FOR ALL OTHER EQUIPMENT: DISCONNECT AND MOTOR CONTROLLER

PROVIDED (FURNISHED AND INSTALLED) BY ELECTRICAL.

MOTOR RATED TOGGLE SWITCH, MAXIMUM 20 AMP RATING, 120/277V, 1-POLE. 'M2'

OR 'M3' SUBSCRIPT INDICATES 2-POLE OR 3-POLE MANUAL MOTOR

CONTROLLER/SWITCH, RESPECTIVELY WITH 30A RATING MAXIMUM.

FLOOR RECEPTACLES & OTHERS

MULTI SERVICE, HAND ACCESS, REACH-IN TYPE, FLUSH, FLOOR BOX WITH

ACTIVATION COVER PLATE AS DESCRIBED IN THE SPECIFICATIONS. FIRE RATED

WHERE APPLICABLE. PROVIDE WITH ONE OR 2 DUPLEX RECEPTACLES, 20A, 125V,

2P-3 WIRE, NEMA 5-20R PER THE SYMBOLOGY. SEE SUBSCRIPT MODIFIER LEGEND

UNDER GENERAL RECEPTACLES. SEE TELECOMMUNICATIONS PLANS FOR

VOICE/DATA REQUIREMENTS AND NOTES.

SW

LUMINAIRES

SURFACE MOUNTED OR SUSPENDED 4'-0" STRIP OR PENDANT TYPE LUMINAIRE.

SURFACE MOUNTED OR SUSPENDED 4'-0" STRIP OR PENDANT TYPE LUMINAIRE

(EMERGENCY POWER)

2' X 4' LUMINAIRE - MOUNTING AND TYPE SHOWN IN LUMINAIRE SCHEDULE

2' X 2' LUMINAIRE - MOUNTING AND TYPE SHOWN IN LUMINAIRE SCHEDULE

1' X 4' LUMINAIRE - MOUNTING AND TYPE SHOWN IN LUMINAIRE SCHEDULE

2' X 4' LUMINAIRE (EMERGENCY POWER) - MOUNTING AND TYPE SHOWN IN

LUMINAIRE SCHEDULE. SUBSCRIPT 'NL' INDICATES NIGHT LIGHT

2' X 2' LUMINAIRE (EMERGENCY POWER) - MOUNTING AND TYPE SHOWN IN

LUMINAIRE SCHEDULE. SUBSCRIPT 'NL' INDICATES NIGHT LIGHT

1' X 4' LUMINAIRE (EMERGENCY POWER) - MOUNTING AND TYPE SHOWN IN

LUMINAIRE SCHEDULE

WALL MOUNTED LUMINAIRE - MOUNTING AND TYPE SHOWN IN LUMINAIRE

SCHEDULE

WALL MOUNTED LUMINAIRE (EMERGENCY POWER) - MOUNTING AND TYPE

SHOWN IN LUMINAIRE SCHEDULE

RECESSED DOWN LIGHT LUMINAIRE

RECESSED DOWN LIGHT LUMINAIRE (EMERGENCY POWER). SUBSCRIPT 'NL'

INDICATES NIGHT LIGHT

EXIT SIGN, WALL MOUNTED WITH 90 MINUTE BATTERY PACK UNIT. SHADED

PORTION DENOTES FACE(S). DIRECTIONAL ARROWS AS INDICATED ON LIFE

SAFETY PLAN.

EXIT SIGN, CEILING MOUNTED WITH 90 MINUTE BATTERY PACK UNIT. SHADED

PORTION DENOTES FACE(S). DIRECTIONAL ARROWS AS INDICATED ON LIFE

SAFETY PLAN.

LUMINAIRE WITH 90 MINUTE BATTERY PACK.

LUMINAIRE WITH 90 MINUTE BATTERY PACK AND CONNECT TO EMERGENCY

POWER SYSTEM.

ANNOTATIONS ASSOCIATED WITH LUMINARIES:

UPPER CASE = LUMINAIRE MARK (REFER TO LUMINAIRE

ALPHANUMERIC (ex. F02) SCHEDULE

LOWER CASE LETTER = INDICATES WHICH CONTROL DEVICE

(SWITCH, SENSOR CONTROLLER) IS

CONTROLLING THE LUMINAIRE

NUMBER = CIRCUIT TO WHICH THE LUMINAIRE IS

CONNECTED

NL = NIGHT LIGHT

F02

12 c

NL

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:0

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

1/8" = 1'-0"

E-001

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

L E

G E

N D

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909482

MLB RMA MBA

JAS

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

PROFESSIONAL

E RN G I N E E

ABBREVIATIONS

A AMPERES

AC ALTERNATING CURRENT OR AIR CONDITIONING

AF AMPERE FRAME

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

AHU AIR HANDLING UNIT

AIC AMPERE INTERRUPTING CAPACITY

AT AMPERE TRIP

ATS AUTOMATIC TRANSFER SWITCH

AWG AMERICAN WIRE GAGE

BAS BUILDING AUTOMATION SYSTEM

BFG BELOW FINISHED GRADE

BPI BYPASS ISOLATION

C CONDUIT OR CONDUCTOR

CB CIRCUIT BREAKER

CCT CORRELATED COLOR TEMPERATURE

CIRC CIRCUIT

CKT CIRCUIT

CL CEILING MOUNTED

COMM COMMUNICATIONS

CRI COLOR RENDERING INDEX

DC DIRECT CURRENT

DDC DIRECT DIGITAL CONTROL

DDP DDC POWER PANEL

DIA DIAMETER

DISC DISCONNECT

DIV DIVISION

DPW DEPARTMENT OF PUBLIC WORKS

ECB ENCLOSED CIRCUIT BREAKER

EF EXHAUST FAN

EGC EQUIPMENT GROUND CONDUCTOR

ELEV ELEVATOR

EMT ELECTRIC METALLIC TUBING

EWC ELECTRIC WATER COOLER

EX EXISTING TO REMAIN

EXD EXISTING TO BE DEMOLISHED

FCU FAN COIL UNIT

FLA FULL LOAD AMPERE

FM FUSE BY MANUFACTURER

GA GAGE

GALV GALVANIZED

GEN GENERATOR

GFCI GROUND FAULT CIRCUIT INTERRUPTER

GFI GROUND FAULT INTERRUPTER

GFP GROUND FAULT PROTECTION

GND GROUND

HP HORSEPOWER RATING

IES ILLUMINATING ENGINEERING SOCIETY

IMC INTERMEDIATE METAL CONDUIT

K KILO (THOUSAND) OR DEGREES KELVIN

KAIC THOUSAND AMPERE INTERRUPTING CAPACITY

KCMIL THOUSAND CIRCULAR MILS

KV KILO-VOLT

KVA KILO-VOLT-AMPERE

KW KILO-WATT

LCP LIGHTING CONTROL PANEL

LED LIGHT EMITTING DIODE

LSI LONG, SHORT, INSTANTANEOUS (TRIPPING)

MAX MAXIMUM

MCB MAIN CIRCUIT BREAKER

MF MODULAR FURNITURE

MH MANHOLE

MIN MINIMUM

MLO MAIN LUGS ONLY

NEC NATIONAL ELECTRIC CODE, NFPA 70

NEMA NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION

NEU NEUTRAL

NF NON-FUSED

NFPA NATIONAL FIRE PROTECTION ASSOCIATION

NTR NEUTRAL

NTS NOT TO SCALE

OC ON CENTER

P POLE

PF POWER FACTOR

PH PHASE

PNL PANEL

PVC POLYVINYLCHLORIDE

RECPT RECEPTACLE

RF RETURN FAN

ROHS RESTRICTION OF HAZARDOUS SUBSTANCES

SD SAFETY DISCONNECT

SF SUPPLY FAN OR SQUARE FOOT

SLD SINGLE LINE DIAGRAM

SP SUMP PUMP

SPD SURGE PROTECTION DEVICE

SS STAINLESS STEEL

ST SHUNT TRIP

SW SWITCHED

TYP TYPICAL

UL UNDERWRITERS LABORATORIES

UON UNLESS OTHERWISE NOTED

UV ULTRA-VIOLET

V VOLT

VFD VARIABLE FREQUENCY DRIVE

W WIRE OR WATT

WP RAINTIGHT (NEMA 3R CLASSIFICATION)

XFMR TRANSFORMER

SWITCHES & LIGHTING CONTROLS

WALL SWITCHES

1-POLE, 20A, 120/277V AC ONLY, QUIET TYPE.

2-POLE, SINGLE THROW, 20A, 120/277V AC ONLY, MOTOR RATED, QUIET TYPE.

3-WAY, 20A, 120/277V AC ONLY, QUIET TYPE.

4-WAY, 20A, 120/277V AC ONLY, QUIET TYPE.

CONTROLS LUMINAIRE WITH SUBSCRIPT "a" ETC.

SOLID STATE DIMMER, FULL RANGE, LINE VOLTAGE TYPE.

SOLID STATE THREE WAY DIMMER, FULL RANGE, LINE VOLTAGE TYPE.

LOW VOLTAGE SWITCH. 'LV' DENOTES LOW VOLTAGE ON/OFF, 'LVD' (SHOWN)

DENOTES LOW VOLTAGE ON/OFF WITH 0-10V DIMMING.

LOW VOLTAGE SWITCH. NUMBER (SHOWN '2') DENOTES NUMBER OF BUTTONS.

SEE CONTROL WIRING DIAGRAM INDICATED ON PLANS FOR CONTROL

STRATEGY.

SWITCHES UNDER A COMMON COVER.

MULTI-ZONE SWITCHING. ANNOTATIONS INDICATE WHICH LUMINAIRE TO BE

CONTROLLED, OR WHICH SET OF LUMINARIES TO BE CONTROLLED. SHOWN -

SUBSET "b" IS CONTROLLED BY 3 WAY SWITCHING.

OCCUPANCY AND LIGHT LEVEL SENSORS

WALL MOUNTED, LINE VOLTAGE, DUAL TECHNOLOGY TYPE OCCUPANCY

SENSOR.

WALL MOUNTED, LOW-VOLTAGE, DUAL TECHNOLOGY OCCUPANCY SENSOR.

WALL MOUNTED INTERIOR DAYLIGHT SENSOR/PHOTOCELL.

CEILING MOUNTED, DUAL TECHNOLOGY, 360 DEGREE COVERAGE, OCCUPANCY

SENSOR. IN CORRIDORS, SUBSCRIPTS (ie. 'b') ARE PROVIDED TO INDICATE

WHICH SENSOR(S) CONTROL LUMINARIES WITH THE SAME SUBSCRIPT.

WIRING DIAGRAM WD01. REFER TO SHEETS EL612 THRU EL618.

ROOF MOUNTED PHOTOCELL.

DAYLIGHT PHOTO SENSORS

DIGITAL, CEILING MOUNTED, INTERIOR DAYLIGHT SENSOR. SUBSCRIPT

INDICATES SWITCH LEG(S) BEING CONTROLLED (WHEN PRESENT).

LOCAL AREA CONTROLLERS

SINGLE OR MULTI-RELAY LOCAL AREA CONTROLLER. MOUNT IN JUNCTION BOX

ABOVE ACCESSIBLE CEILING OR MOUNT ON DIN RAIL ENCLOSURE AS

INDICATED ON LIGHTING CONTROL WIRING DIAGRAMS ON SHEETS EL612

THROUGH EL618. IN SPACES WITH NO ACCESSIBLE CEILING, PROVIDE AN

ACCESS PANEL ADJACENT TO THE LOCAL AREA CONTROLLER. WHEN LOCATED

ABOVE ACCESSIBLE CEILING, PROVIDE LAMINATED LABEL STATING "LIGHTING

CONTROL ROOM CONTROLLER" ON CEILING GRID DIRECTLY BELOW DEVICE

LOCATION. PROVIDE SEPARATE RELAY FOR EACH SWITCH LEG. SUPERSCRIPT

'15' INDICATES CIRCUIT IN PRE-WIRED MODULAR FURNITURE TO BE

CONTROLLED.

'R' DENOTES USE FOR SWITCHED RECEPTACLES. 'L' DENOTES USE FOR

LIGHTING. NUMBER (SHOWN '1') INDICATES NUMBER OF RELAYS.

a b a

D

LVD

DT

DT

WD01

PC

a

DS

L1

LAC

- TYPICAL AUTOMATIC LIGHTING CONTROL PANELBOARD NAMING SCHEME -

FIRST LCP - LIGHTING CONTROL PANEL

POSITION

SECOND 1 - FIRST FLOOR

POSITION 2 - SECOND FLOOR

(1 CHARACTER)

THIRD POSITION A - ELECTRICAL ROOM 'A'

(1 CHARACTER) B - ELECTRICAL ROOM 'B'

LCP-1B

PS

DT

LV2

D b

SITE LEGEND

T

P

EUP

EUP

UP

EXISTING UTILITY POLE.

EXISTING SITE LIGHT.

EXISTING SITE LIGHT TO BE DEMOLISHED.

POLE LIGHT (SEE LUMINARIES SCHEDULE).

WALL MOUNTED LUMINAIRE (SEE LUMINARIES

SCHEDULE).

INDICATES CIRCUIT INSTALLED BELOW GRADE.

EXISTING PAD MOUNT TRANSFORMER.

PAD MOUNT TRANSFORMER (HEAVY LINE INDICATES

FRONT OF EQUIPMENT).

EXISTING POWER MANHOLE.

EXISTING POWER MANHOLE TO BE DEMOLISHED.

POWER MANHOLE.

EXISTING COMMUNICATIONS MANHOLE.

EXISTING COMMUNICATIONS MANHOLE TO BE

DEMOLISHED.

COMMUNICATIONS MANHOLE.

POWER OR LIGHTING HANDHOLE

EXISTING UNDERGROUND PRIMARY TO BE

DEMOLISHED. SEE DRAWING NOTES AND SINGLE LINE

DIAGRAM FOR ADDITIONAL DIRECTION.

EXISTING UNDERGROUND PRIMARY.

UNDERGROUND PRIMARY.

EXISTING UNDERGROUND SECONDARY TO BE

DEMOLISHED.

EXISTING UNDERGROUND SECONDARY.

UNDERGROUND SECONDARY.

EXISTING UNDERGROUND COMMUNICATIONS

DUCTBANK TO BE DEMOLISHED.

EXISTING UNDERGROUND COMMUNICATIONS

DUCTBANK.

UNDERGROUND COMMUNICATIONS DUCTBANK.

EXISTING OVERHEAD COMMUNICATIONS CABLES TO

BE DEMOLISHED.

EXISTING OVERHEAD COMMUNICATIONS CABLES.

T

EX

EUS

US

EUS

P

EXD

P

T

EX

T

EXD

T

EUC

UC

EUC

EX

EX

EXD

HH

EOC

EOC

SINGLE LINE DIAGRAM

EXISTING CABLING AND/OR AND CONDUIT TO REMAIN.

EXISTING UNDERGROUND PRIMARY TO BE DEMOLISHED.

EXISTING UNDERGROUND PRIMARY TO REMAIN.

UNDERGROUND PRIMARY.

UNDERGROUND SECONDARY.

WATT-HOUR DEMAND METER.

PANELBOARD.

STEP-DOWN TRANSFORMER WITH GROUNDING SHOWN. REFER TO

GROUNDING DIAGRAM ON SHEET EP701.

TRANSFORMER WINDINGS.

FUSE.

SWITCH.

METER.

CURRENT TRANSFORMER.

DIGITAL, SOLID STATE, ELECTRONIC, DRAW-OUT CIRCUIT BREAKER WITH

ADJUSTABLE LSIG TRIP SETTINGS. GFP=GROUND FAULT PROTECTION.

MOLDED CASE CIRCUIT BREAKER WITH ADJUSTABLE SOLID STATE

ELECTRONIC TRIP (LSI FUNCTIONS).

MOLDED CASE CIRCUIT BREAKER (THERMAL MAGNETIC).

CIRCUIT BREAKER TAG. 3=NUMBER OF POLES/ 50AT=TRIP SETTING OF THE

BREAKER/ 100AF=FRAME SIZE OF THE BREAKER.

CIRCUIT BREAKER IN NEMA 1 ENCLOSURE - SURFACE MOUNTED, 22,000AIC

SHOWN. 'LSI' INDICATES ADJUSTABLE ELECTRONIC TRIP BREAKER WITH LSI

FUNCTIONS. SEE CIRCUIT BREAKER TAG ABOVE.

DISCONNECT SWITCH.

SURGE PROTECTION DEVICE.

FEEDER REFERENCE, SEE SHEET EP607 FOR DESCRIPTION.

AUTOMATIC TRANSFER SWITCH. REFER TO SPECIFICATIONS AND CALLOUT

IN SINGLE LINE DIAGRAM FOR MORE INFORMATION.

ENGINE/GENERATOR SET.

GENERATOR ALARM PANEL.

GENERATOR SET REMOTE ALARM PANEL.

T

XXXX

EUP

EUP

UP

US

WHD

M

B22KAIC

GFP

SPD

NE

GE

GAP

RAP

50AT

100AF

LSI

50AT

100AF

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:0

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

1/8" = 1'-0"

E-002

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

L E

G E

N D

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909483

MLB RMA MBA

JAS

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

DEMOLITION NOTES

1. IT IS STRONGLY RECOMMENDED THAT THE CONTRACTOR VISIT THE SITE PRIOR TO BIDDING TO ASCERTAIN EXISTING CONDITIONS AS HE WILL BE RESPONSIBLE FOR EXISTING CONDITIONS AS

REQUIRED IN OTHER NOTES.

2. REMOVED EQUIPMENT NOT DESIRED BY THE OWNER MUST BE DISPOSED OF OFF SITE BY THE CONTRACTOR AT NO ADDITIONAL COST. WIRE AND CONDUIT WILL BECOME PROPERTY OF THE

CONTRACTOR AND MUST BE DISPOSED OF OFF SITE.

3. CONTRACTOR IS RESPONSIBLE FOR REMOVAL OF PCB-CONTAINING FLUORESCENT BALLASTS AND MERCURY CONTAINING FLUORESCENT LAMPS FROM ALL DEMOLISHED LUMINARIES. BALLAST

MUST BE DELIVERED FOR DISPOSAL BY THE GOVERNMENT.

GENERAL NOTES

1. PROVIDE ALL ELECTRICAL WORK AND MATERIAL AS NEW UNLESS INDICATED OTHERWISE.

2. MAINTAIN NEC MINIMUM CLEARANCE IN FRONT OF ALL SWITCHGEAR, SWITCHBOARDS, SAFETY SWITCHES, PANELBOARDS, TRANSFER SWITCHES, TRANSFORMERS, AND OTHER ELECTRICAL

EQUIPMENT. DETERMINE PROPER CLEARANCE BEFORE INSTALLATION. DIMENSIONS OF EQUIPMENT SHOWN ARE BASED ON A PARTICULAR MANUFACTURER. IF DIMENSIONS OF EQUIPMENT FURNISHED DIFFER FROM THOSE ON THE DRAWINGS, ENSURE THAT ALL EQUIPMENT FITS IN THE ROOM OR SPACE ALLOCATED WITH PROPER CLEARANCE.

3. PROVIDE ALL CIRCUIT BREAKERS RATED 1200A OR LARGER WITH ARC ENERGY REDUCTION. PROVIDE ENERGY-REDUCING MAINTENANCE SWITCHING WITH LOCAL STATUS INDICATOR.

4. PRIOR TO ROUGH-IN, PROVIDE SCALED WALL ELEVATIONS WHERE ALL ALARM CABINETS, SIGNAL CABINETS, ETC. ARE INSTALLED IN OTHER THAN MECHANICAL AND ELECTRICAL ROOMS FOR

APPROVAL.

5. PROVIDE AN ARC FLASH STUDY AND COORDINATION ONCE THE ELECTRICAL (AS-BUILT SYSTEM) IS IN PLACE THAT WILL YIELD THE REQUIRED ARC FLASH WARNING LABELS, IN ACCORDANCE WITH NEC

110.16 (A) AND NFPA 72E, AS WELL AS THE FINAL ADJUSTABLE TRIP ELECTRONIC CIRCUIT BREAKER SETTINGS.

6. PROVIDE ALL SWITCHBOARDS AND PANELBOARDS WITH A PERMANENT SIGN TO WARN QUALIFIED PERSONS OF POTENTIAL ELECTRIC ARC FLASH HAZARDS AND THAT PERSONNEL PROTECTIVE

EQUIPMENT (PPE) IS REQUIRED. LOCATE THE MARKING SO THAT IT IS CLEARLY VISIBLE TO QUALIFIED PERSONS BEFORE SERVICING THE EQUIPMENT. PROVIDE LABEL IN ACCORDANCE WITH NFPA 110.16.

7. PROVIDE A LAMINATED PLASTIC LABEL ON THE SERVICE SWITCHBOARD TO INDICATE THE MAXIMUM AVAILABLE FAULT CURRENT AT THE SERVICE AND THE DATE THE FAULT CALCULATION WAS

PERFORMED IN ACCORDANCE WITH NEC 110.24. SEE SINGLE LINE DIAGRAMS FOR DATA.

8. PROVIDE SIGNAGE AT THE SERVICE SWITCHBOARD INDICATING THE LOCATION OF THE GENERATOR SET.

9. COORDINATE WITH PANELBOARD MANUFACTURER AND PROVIDE CIRCUIT BREAKERS IN THE PANELBOARD SUBMITTAL THAT WILL COORDINATE TO 0.1 SECONDS FROM THE SERVICE SWITCHBOARD TO

ALL DOWNSTREAM CIRCUIT BREAKERS (INCLUDING BRANCH PANEL CIRCUIT BREAKERS).

10. PROVIDE RECESSED MOUNTED PANELBOARDS MUST HAVE FOUR (4) 3/4" EMPTY CONDUITS STUBBED UP ABOVE THE CEILING UNLESS OTHERWISE NOTED ON THE PANELBOARD SCHEDULE.

11. PROVIDE A MINIMUM #10 INSULATED CONTINUOUS COPPER GROUNDING CONDUCTOR TO BOND THE GROUNDING BUSSES IN ALL PANELBOARDS WITH BRANCH CIRCUITS SERVING THE SAME PATIENT

CARE AREA.

12. PROVIDE ENGRAVED LAMINATED MELAMINE TYPE LABELS DESCRIBING THE LOAD SERVED FOR EACH CIRCUIT BREAKER IN MAIN SWITCHBOARD AND ALL DISTRIBUTION TYPE PANELBOARDS. ALSO

PROVIDE SAME FOR EACH DISCONNECT SWITCH.

13. PROVIDE LIQUID-TIGHT FLEXIBLE METAL CONDUITS WITH SUITABLE FITTINGS FOR FLEXIBLE CONDUITS WHICH ARE INSTALLED OUT-OF-DOORS, IN ANY MECHANICAL EQUIPMENT ROOM, OR IN

NORMALLY WET AREAS.

14. PROVIDE FLEXIBLE CONDUIT FOR ALL CONDUITS PASSING THROUGH EXPANSION JOINTS. SEE ARCHITECTURAL DRAWINGS FOR EXPANSION JOINT LOCATIONS.

15. PROVIDE MINIMUM OF AWG #12 COPPER CONDUCTOR AND 3/4" CONDUIT FOR BRANCH CIRCUITS AND HOMERUNS UNLESS OTHERWISE NOTED. PROVIDE A DEDICATED NEUTRAL FOR EACH PHASE IN

SINGLE PHASE BRANCH CIRCUITS. PROVIDE SEPARATE DEDICATED GROUNDING CONDUCTOR (#12 MINIMUM) IN EACH CONDUIT. DO NOT USE ALUMINUM CONDUCTORS.

16. DO NOT INSTALL MORE THAN THREE PHASE CONDUCTORS IN ONE CONDUIT UNLESS NOTED OTHERWISE.

17. DO NOT ROUTE CONDUIT THROUGH ELEVATOR HOIST WAY OR MACHINE ROOM UNLESS IT SPECIFICALLY SERVES EQUIPMENT IN THAT ROOM.

18. PROVIDE SEALING FOR ALL UNDERGROUND CONDUIT RUNS ENTERING THE BUILDING AND IN MANHOLES TO PREVENT THE ENTRANCE OF MOISTURE AND GASES.

19. ROUTE CONDUIT FOR RECEPTACLE CIRCUITS AND OTHER POWER BRANCH CIRCUIT WIRING AS WELL AS COMMUNICATION SYSTEMS CONDUITS OVERHEAD UNLESS NOTED OTHERWISE.

20. PROVIDE CONDUIT FOR DEVICE BOXES AS REQUIRED FOR THERMOSTATS. THERMOSTATS ARE SHOWN ON MECHANICAL DRAWINGS

21. IN ALL ROOMS WITHOUT FINISHED CEILINGS INSTALL ALL ELECTRICAL CONDUITS AS CLOSE TO THE STRUCTURAL CEILING AS POSSIBLE.

22. UNLESS NOTED OTHERWISE, THE CONDUIT SIZES SHOWN ON THE DRAWINGS FOR POWER AND LIGHTING ARE BASED ON THHN/THWN-2 CONDUCTORS. IF A DIFFERENT TYPE OF CONDUCTOR

INSULATION IS USED RATHER THAN TYPE THHN/THWN-2, NOTIFY THE CONTRACTING OFFICER, INCLUDING ANY INSTANCES WHERE AN INCREASE IN CONDUIT SIZE WILL BE REQUIRED.

23. PROVIDE ALL REQUIRED LUGS IN ELECTRICAL EQUIPMENT TO MATCH THE NUMBER OF CONDUCTORS PER PHASE, NEUTRAL AND GROUND FOR PARALLEL RUNS. PROVIDE ALL RUNS IN A PARALLEL

RUN SO THAT THEY ARE THE SAME PHYSICAL LENGTH.

24. PROVIDE ALL INTERIOR CONDUIT CONCEALED UNLESS SPECIFICALLY SHOWN TO BE EXPOSED. PROVIDE ALL CONDUIT SERVING DEVICES AND EQUIPMENT ON THE EXTERIOR OF THE BUILDING

CONCEALED IN WALLS OR COLUMNS. NO CONDUITS ARE ALLOWED TO BE EMBEDDED HORIZONTALLY WITHIN THE THICKNESS OF CONCRETE SLABS AND CONCRETE FILL ON METAL DECK.

25. DO NOT USE METAL CLAD CABLE 'MC' OR ARMORED CABLE 'AC' ON THIS PROJECT.

26. PROVIDE ELECTRIC WATER COOLER GFI RECEPTACLES (INDICATED BY "EWC" ON PLANS ) ADJACENT TO THE WATER COOLER ASSEMBLY. COORDINATE WITH PLUMBING TRADE. IF RECEPTACLE IS

REQUIRED TO BE INSIDE THE HOUSING OF THE WATER COOLER, USE STANDARD RECEPTACLE AND PROVIDE A GROUND FAULT INTERRUPTING DEVICE ADJACENT TO WATER COOLER TO MAINTAIN

REQUIRED ACCESSIBILITY FOR THE TEST SWITCH.

27. MECHANICAL TRADE FURNISHES MOTOR CONTROL DEVICES, ELECTRICAL TRADE MAKES ELECTRICAL CONNECTIONS FOR SAME.

28. COORDINATE WITH ALL MECHANICAL AND PLUMBING TRADES FOR SPACE REQUIREMENTS IN MECHANICAL ROOMS, CORRIDORS, SHAFTS, ABOVE CEILING, ETC. THIS INCLUDES SPACE ABOVE PANELS

WHERE DUCTS AND PIPING ARE PROHIBITED. SEE MECHANICAL PLANS FOR EXACT LOCATIONS OF MECHANICAL EQUIPMENT.

29. PROVIDE ENCLOSURES LISTED FOR ENVIRONMENT (CORROSIVE ATMOSPHERES, COASTAL AREAS, ETC.) IN ACCORDANCE WITH APPLICABLE DESIGN CRITERIA.

30. WHERE WALL SWITCHES AND CONTROL DEVICES SUCH AS THERMOSTATS ARE SHOWN AT THE SAME LOCATION IN PLAN VIEW (CONTROL DEVICES SUCH AS THERMOSTATS ARE SHOWN ON THE

MECHANICAL DRAWINGS), PROVIDE THE CONTROL DEVICE DIRECTLY IN LINE ABOVE THE SWITCH.

31. THE LOCATION OF LUMINAIRES IN MECHANICAL ROOMS, ELECTRICAL ROOMS MACHINE ROOMS, ETC. ARE SHOWN FOR BID PURPOSES ONLY. PROVIDE LUMINAIRES SO AS TO COORDINATE WITH ALL

TRADES AND ARRANGED FOR MAXIMUM LIGHTING DISTRIBUTION OF THE AREA.

32. REVIEW SHOP DRAWING SUBMITTALS OF OTHER TRADES FOR DISCREPANCIES BETWEEN THE SUBMITTED ITEM(S) AND THE ELECTRICAL DESIGN INFORMATION. VERIFY AND COORDINATE ALL

CONNECTIONS TO EQUIPMENT WITH SPECIFIC EQUIPMENT FURNISHED.

33. IN MANY CASES THROUGHOUT THE PLANS, EQUIPMENT CONNECTIONS ARE IDENTIFIED ON THE PLANS WITH A LETTER AND A FOUR DIGIT NUMBER. EXAMPLE: R7000 IS A REFRIGERATOR. THE

EQUIPMENT SCHEDULE FOR THESE ITEMS IS SHOWN ON THE ARCHITECTURAL SHEET A-680.

34. THE ELECTRICAL CHARACTERISTICS (SIZE, VOLTAGE, NUMBER OF CONDUCTORS, ETC.) OF ELECTRICAL CONNECTIONS TO MECHANICAL EQUIPMENT, PLUMBING EQUIPMENT, ELEVATOR MOTORS AND

MEDICAL EQUIPMENT ARE BASED ON A PARTICULAR MANUFACTURER. IF THE REQUIRED ELECTRICAL CONNECTIONS TO EQUIPMENT DIFFER FROM THAT SHOWN ON THE DRAWINGS, PROVIDE THE CORRECT CONNECTIONS FOR THE SUBMITTED AND INSTALLED EQUIPMENT. SEE MECHANICAL AND PLUMBING EQUIPMENT SCHEDULES ON MECHANICAL AND PLUMBING DRAWINGS FOR ELECTRICAL REQUIREMENTS. COORDINATE WITH MANUFACTURER'S DATA IN OWNER APPROVED MECHANICAL AND PLUMBING SUBMITTALS SO AS TO ENSURE THAT THE BRANCH CIRCUIT AND OVERCURRENT PROTECTION ARE PROPERLY SIZED FOR THE EQUIPMENT BEING PROVIDED. PROVIDE (AT NO ADDITIONAL COST TO GOVERNMENT) PROPERLY SIZED ELECTRICAL EQUIPMENT AND CIRCUITS BASED ON THE MANUFACTURER'S DATA IN THE APPROVED EQUIPMENT SUBMITTAL. THE CONTRACTING OFFICER MUST APPROVE ANY PROPOSED CHANGES IN THE BRANCH CIRCUIT AND OVERCURRENT

PROTECTION.

35. COORDINATE WITH MANUFACTURER'S DATA IN OWNER APPROVED MEDICAL/DENTAL EQUIPMENT SUBMITTALS SO AS TO ENSURE THAT THE BRANCH CIRCUIT AND OVERCURRENT PROTECTION ARE PROPERLY SIZED. PROVIDE (AT NO ADDITIONAL COST TO THE GOVERNMENT) PROPERLY SIZED ELECTRICAL EQUIPMENT AND CIRCUITS BASED ON THE MANUFACTURER'S DATA IN THE APPROVED SUBMITTALS. THE CONTRACTING OFFICER MUST APPROVE ANY CHANGES IN THE BRANCH CIRCUIT AND OVERCURRENT PROTECTION.

36. VERIFY AND COORDINATE ALL MOUNTING HEIGHTS OF ALL DEVICES MOUNTED IN CASEWORK OR IN OR ABOVE COUNTERS WITH SPECIFIC EQUIPMENT FURNISHED.

37. PROVIDE A UL-LISTED ASSEMBLY FOR PROTECTION AROUND DEVICE BOXES (RECEPTACLES, LIGHT SWITCHES, TELEPHONE, ETC.) OVER 16 SQUARE INCHES IN SMOKE AND FIRE WALLS. WHERE

OUTLET BOXES ARE ON OPPOSITE SIDES OF A FIRE WALL, PROVIDE A 24" HORIZONTAL SEPARATION BETWEEN THEM OR PROVIDE PROTECTION AS DESCRIBED PREVIOUSLY.

38. DO NOT MOUNT DEVICES BACK-TO-BACK.

39. PROVIDE ALL NORMAL RECEPTACLES, SWITCHES, ETC WITH STAINLESS STEEL COVER PLATES. ENGRAVE THE WORD 'EMERGENCY' ON THE DEVICE COVERPLATE FOR RECEPTACLES AND LIGHT

SWITCHES ON 'EMERGENCY' POWER. USE AN APPROVED PERMANENT MEANS TO INDICATE PANELBOARD AND CIRCUIT NUMBER ON EACH RECEPTACLE COVER PLATE. SEES DETAIL ON EP502.

40. PROVIDE BARRIERS BETWEEN ALL 277V SWITCHES MOUNTED UNDER THE SAME COVER PLATE WITH OTHER 277V SWITCHES ON DIFFERENT PHASES OR 120V SWITCHES.

41. PROVIDE WALL MOUNTED DEVICES WITH THE MOUNTING HEIGHTS ABOVE FINISHED FLOOR AS INDICATED IN THE LEGEND AND IN THE FOLLOWING LIST UNLESS NOTED OTHERWISE ON THE PLANS

(MOUNTING HEIGHTS ARE TO CENTERLINE OF DEVICE):

SWITCHES (GENERAL) = 48" RECEPTACLES (GENERAL) = 18"

FOR SPECIAL MOUNTING HEIGHTS OF DEVICES. SEE ELECTRICAL PLANS AND ARCHITECTURAL ELEVATIONS.

42. WHERE AN ELECTRICAL RECEPTACLE IS ADJACENT TO A SINK, LOCATE THE RECEPTACLE LEAST 6" HORIZONTALLY AWAY FROM THE SINK'S TOWEL DISPENSER. DO NOT LOCATE THE RECEPTACLE

UNDER A TOWEL DISPENSER.

43. PROVIDE ALL COMMUNICATION CLOSET RECEPTACLES WHICH ARE CONNECTED TO LIFE SAFETY OR CRITICAL POWER LABELS WITH FACE PLATES HAVING THE WORDS 'LIFE SAFETY' OR 'CRITICAL'

(RESPECTIVELY) ENGRAVED ON THEM.

44. PROVIDE ALL DEVICE BOXES FOR POWER, LIGHTING OR COMMUNICATIONS DEVICES FLUSH MOUNTED UNLESS OTHERWISE NOTED.

45. PROVIDE LEAD LINING FOR ALL WALL MOUNTED, FLUSH ELECTRICAL BOXES AND ENCLOSURES IN RADIOGRAPHIC ROOMS WITH LEAD-LINED WALLS, SO AS TO MAINTAIN INTEGRITY OF LEAD

PROTECTION.

46. SEE ARCHITECTURAL REFLECTED CEILING PLANS FOR EXACT LOCATION OF ALL CEILING MOUNTED EQUIPMENT.

47. PROVIDE A COMPLETELY CONCEALED LIGHTNING PROTECTION SYSTEM WITH U.L. MASTER CERTIFICATE .

48. PROVIDE SEISMIC SUPPORTS FOR ALL EQUIPMENT. FOR EQUIPMENT MOUNTED ON HOUSEKEEPING PADS, SEE STRUCTURAL FOR PAD REQUIREMENTS. PROVIDE CABLE TIES TO STRUCTURE FOR ALL

LUMINARIES, AND PROVIDE EARTHQUAKE CLIPS TO TIE LUMINAIRES TO GRID CEILING.

49. PROVIDE STRUCTURAL BACKING AS REQUIRED FOR PROPER SUPPORT OF WALL MOUNTED ELECTRICAL EQUIPMENT. SEE ARCHITECTURAL SHEET A-542, DETAILS D1 AND D2 FOR ADDITIONAL

INFORMATION.

50. IN THE EVENT OF CONFLICTS IN THE DESIGN, PROVIDE A 'REQUEST FOR INFORMATION' (RFI) BEFORE THE START OF INSTALLATION TO AVOID RE-WORK AND ITS ASSOCIATED COSTS.

51. ADHERE TO NFPA 99 CONCERNING RECEPTACLES AND GROUNDING SYSTEM PERFORMANCE AND TESTING. PROVIDE DOCUMENTATION OF SUCCESSFUL TESTING AS A PRE-REQUISITE TO

GOVERNMENT ACCEPTANCE OF RECEPTACLES AND GROUNDING SYSTEMS.

52. WHERE CONDUIT PASSES THROUGH CONCRETE FLOOR AND/OR BEAMS, PROVIDE APPROPRIATE SLEEVE AND COORDINATE EXACT LOCATION WITH STRUCTURAL.

53. DO NOT ROUTE CONDUIT HORIZONTALLY ON ROOFS. ROUTE CONDUIT SERVING ROOF MOUNTED EQUIPMENT FROM ABOVE THE CEILING OF THE LEVEL BELOW THE ROOF. TURN CONDUIT UP THROUGH

THE ROOF AT THE EQUIPMENT SERVED. SEE DETAILS ON ARCHITECTURAL DRAWINGS FOR FLASHING AND/OR SEALING OF CONDUIT PENETRATIONS.

54. PROVIDE RECEPTACLE RETENTION FORCE OF GROUNDING BLADE TEST IN DENTAL TREATMENT ROOMS IN ACCORDANCE WITH NFPA 99, CHAPTER 6 'ELECTRICAL SYSTEMS'.

PHASING NOTES

1. PHASING OF THIS PROJECT WILL FOLLOW THE CONSTRUCTION SEQUENCE GIVEN ON SHEET C-003.

2. NO ELECTRICAL WORK IS ANTICIPATED UNDER PHASE 1.

3. EXISTING ELECTRICAL SERVICES TO BUILDINGS 6002 AND 6008 WILL REMAIN ENERGIZED UNDER PHASES 1, 2 AND 3.

4. EXISTING SITE LIGHTS (CALLED OUT IN CONSTRUCTION LIMITS PHASE 2 AND 3) WILL BE CIRCUIT TRACED AND DOCUMENTED BEFORE ANY POWER IS DISCONNECTED ON THE SITE.

5. EXISTING BUILDING 602 WILL BE DEMOLISHED AFTER THE EXISTING ELECTRIC SERVICE TRANSFORMER HAS BEEN DEMOLISHED.

6. PRIMARY POWER RECONFIGURATION AND SITE LIGHTING WORK ON THE EAST SIDE OF ALASKA STREET WILL BE ACCOMPLISHED DURING PHASE 2.

7. SITE LIGHTING CIRCUITS ON THE WEST SIDE OF ALASKA STREET WILL BE STUBBED OUT DURING PHASE 2.

8. EXISTING BUILDING 674 WILL BE DEMOLISHED AND PARKING LOT CONSTRUCTED DURING PHASE 3.

9. PRIMARY POWER RECONFIGURATION AND SITE LIGHTING WORK ON THE WEST SIDE OF ALASKA STREET WILL BE EXTENDED AND COMPLETED DURING PHASE 3.

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

NOT TO SCALE

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:0

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

E-003

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

N O

T E

S

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909484

MLB RMA MBA

JAS

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

W

WW

W

W

WW

SILTED

AREA

BLDG 674

2 STORY E

E

A

E

M

W

BLD

G

STO

R Y

EX. BLDG 602 TRANSFORMER

TO BE DEMOLISHED (NOTE 1)

T

P

EX

EX

E U

P

EUP

EXISTING

SECTIONALIZING

CABINET TO REMAIN.

SEE NOTE 6.

P

EUP

P

EX

EX

EUP

TEX

P EX

P EXD

EU

P

E U

P

T

T

EX

EX

EUC

EX. BLDG 674

TRANSFORMER TO

BE DEMOLISHED

EUC

NOTE 4

TEXD

NOTE 5

T

EX. BUILDING 6008

TRANSFORMER TO REMAIN

T

NOTE 3

NOTE 3

T

TEUP

EX. BLDG 6002

TRANSFORMER

TO REMAIN

EUP

NOTE 4

CONSTRUCTION

LIMITS PHASE 3

CONSTRUCTION

LIMITS PHASE 2

E U

C

EUS

MH-1

MH-2

MH-3

MH-5

MH-4

NOTE 4

EX

EX

EXD EXD

EXD

EXD

EXD

EXD

EX

EXD

EXD

EXD

EXD

EXD

EXD

EX

EX

EX

ER

EX

EXEX

NOTE 3

NOTE 1

NOTE 2

NOTE 1

NOTE 1

NOTE 1 NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 7

NOTE:

REFER TO PHASING

NOTES ON SHEET E-003

NOTE 8

NOTE 2NOTE 2

NOTE 2

NOTE 2

BOULEVARD DE FRANCE

BOULEVARD DE FRANCE

A

LA

S K

A S

T R

E E

T

NOTE 2

NOTE 5

E O

CEOC

E O

C

EX. LOAD CENTER TO BE

DEMOLISHED (NOTE 1)

E O

C

E O

C

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

SCALE: 1"=30'-0"

20' 40' 60' 877

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:0

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

1" = 30'-0"

SCALE: 1" = 30'-0"

ES101

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

S

IT

E P

L A

N

D E

M O

L

IT

IO

N

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909485

MLB RMA MBA

ELECTRICAL SITE PLAN - DEMOLITION

JAS

1. DO NOT REMOVE OR DISCONNECT FROM POWER THE EXISTING BLDG 602 TRANSFORMER OR LOAD CENTER UNTIL IT IS DETERMINED WHICH SITE LIGHT CIRCUITS NEED TO BE RE-FED. PROVIDE CIRCUIT TRACING TO DETERMINE WHICH STREET LIGHT POLES ARE AFFECTED BY THE LOAD CENTER REMOVAL. CONTRACTOR MUST IDENTIFY AND LOCATE POINTS IN THE SITE LIGHTING CIRCUITS WHICH WILL REMAIN AFTER DEMOLITION AND BE ACCESSIBLE AFTER CONSTRUCTION. PROVIDE

HANDHOLES AT THESE LOCATIONS FOR CONNECTION TO EXISTING CIRCUITS.

2. REMOVE CABLE AND DUCTBANK IN THEIR ENTIRETY.

3. REMOVE EXISTING PRIMARY LOOP CABLING FROM BLDG 602 TRANSFORMER BACK TO MANHOLE MH-3 AND REMOVE

DUCTBANK IN ITS ENTIRETY. PLUG ALL MANHOLES ENTRANCE WHERE AN OPENING IS LEFT FROM DUCTBANK DEMOLITION.

4. EXISTING DUCTBANK TO REMAIN. REMOVE EXISTING PRIMARY LOOP CABLES CALLED OUT ON SHEET ES601. BLDG 6002

TRANSFORMER WILL REMAIN ENERGIZED THRU THE 2ND LOOP FEEDER.

5. EXISTING DUCTBANK TO REMAIN. REMOVE EXISTING PRIMARY LOOP CABLES CALLED OUT ON SHEET ES601. BLDG 6008

TRANSFORMER WILL REMAIN ENERGIZED THRU THE 2ND LOOP FEEDER.

6. EXISTING SECTIONALIZING CABINET IS MOUNTED DIRECTLY ON TOP OF EXISTING MANHOLE.

7. PROVIDE CIRCUIT TRACING TO CONFIRM EXISTING LIGHT POLES ARE PART OF THE DEMOLITION CIRCUIT AND REPORT

FINDINGS TO ENGINEER OF RECORD.

8. PROVIDE CIRCUIT TRACING TO CONFIRM EXISTING LIGHT POLES ARE NOT PART OF THE DEMOLITION CIRCUIT AND REPORT

FINDINGS TO ENGINEER OF RECORD.

PLAN

NORTH

1. PROVIDE CIRCUIT TRACING TO CONFIRM EXISTING LIGHT POLES ARE PART OF THE DEMOLITION WORK AND

REPORT FINDINGS TO ENGINEER OF RECORD.

2. PROVIDE CIRCUIT TRACING TO CONFIRM EXISTING LIGHT POLES ARE NOT PART OF THE DEMOLITION WORK

AND REPORT FINDINGS TO ENGINEER OF RECORD.

3. REMOVE CABLE AND DUCTBANK IN THEIR ENTIRETY. PLUG ALL MANHOLES ENTRANCE WHERE AN OPENING IS

LEFT FROM DUCTBANK DEMOLITION.

4. SEE SHEET ES601 FOR RE-ESTABLISHMENT OF LOOP CONNECTION.

CONSTRUCTION LIMITS PHASE 3 NOTES: CONSTRUCTION LIMITS PHASE 2 NOTES:

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

PROFESSIONAL

E RN G I N E E

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

W

W

WW

W

WW

SILTED

AREA

CHILLER

CHILLER

ROOF

RECYCLE

TRAILER

T

CLINIC

FFE = 11.50

WM

12" W A

TE

R

M A

IN

12" W A

TE

R

M A

IN

F H

P I0

6" WATER

T

T

P

EX

EX

U P

EXISTING

SECTIONALIZING

CABINET

P

PEX

EX

UP

P

EX

P

EX

T

T

EX

EX

NOTE 1

NOTE 1

PUP

ES401

A1 T

EX. BUILDING 6008

TRANSFORMER TO REMAIN

T

EX

T

EX

UP T

EX. BLDG 6002

TRANSFORMER

EUP

CONSTRUCTION

LIMITS PHASE 3

CONSTRUCTION

LIMITS PHASE 2

G E

N

U S

MH-2

MH-3

MH-1

MH-4

MH-6. SEE DETAILS

ON SHEET ES502

NOTE 2

EX

EX

ER

EX

ES501

A1

ES501

A4 ES501

A2

LOAD BANK

CONNECTION

NOTE 1

UP

WIREWAY AND ECB's

IN RM 1A01A

SC-1

ES503

C3

NOTE:

REFER TO PHASING

NOTES ON SHEET E-003

ES501

A1

FRONT OF

TRANSFORMER

MSWGR IN RM 1A01B

72"

BFG

BOULEVARD DE FRANCE

BOULEVARD DE FRANCE

A

LA

S K

A S

T R

E E

T

VSS EXTENDER

PEDESTAL. SEE

SHEET TS101

GFI

SEE NOTE 1

10's, 1"C.

SEE NOTE 3

ES501

A1

HH

10's, 1"C.

SEE NOTE 4

HH EQ21A:9

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

SCALE: 1"=30'-0"

20' 40' 60' 877

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:1

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

1" = 30'-0"

SCALE: 1" = 30'-0"

ES102

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

S

IT

E P

LA

N

P

O W

E R

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909486

MLB RMA MBA

ELECTRICAL SITE PLAN - POWER

JAS

1. PROVIDE NEW CONDUCTORS IN EXISTING DUCTBANK AS SHOWN ON ES602.

2. EXISTING SECTIONALIZING CABINET IS MOUNTED DIRECTLY ON TOP OF MANHOLE.

3. ROUTE CONDUIT, VIA DIRECTIONAL BORE, IN SAME VICINITY AS SECURITY CAMERA AND

LIGHTING CIRCUIT CONDUITS WHEN CROSSING ALASKA STREET. REFER TO SHEET CU102

FOR ADDITIONAL INFORMATION.

4. SET HANDHOLE IN PLACE UNDER PHASE 2. PROVIDE 30'-0" OF EXTRA CABLE LENGTH FOR

EXTENSION TO VSS EXTENDER PEDESTAL IN PHASE 3.

PLAN

NORTH

1. SURFACE MOUNT RECEPTACLE INSIDE NEMA 4X ENCLOSURE. COORDINATE WITH SECURITY CAMERA

ENCLOSURE MANUFACTURER FOR FINAL LOCATION.

CONSTRUCTION LIMITS PHASE 3 NOTES: CONSTRUCTION LIMITS PHASE 2 NOTES:

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

WW

W

WW

T

CHILLER

CHILLER

G E

N

ROOF

RECYCLE

TRAILER

T

P

CLINIC

FFE = 11.50

M A

T C

H

LI

N E

M A

T C

H

LI

N E

A L

A S

K A

S T

BOULEVARD DE FRANCE

BOULEVARD DE FRANCE

CONSTRUCTION

LIMITS PHASE 3

CONSTRUCTION

LIMITS PHASE 2

EX

EX

EX

EX

EX

EX

EX

EXEX

L4

L4

L4

L3 L4

L4

L4

L4

L4

L4

L3

L1

L1

L2

L1

L1

L1

L1

L1

L1

L2

L1

L1

L2

L4

L3 L4

L1

L1

L2

L1

L1

L2

L2

L1

L1

N41C:13

ELECTRICAL

ROOM 1C

N41C:12,14

THRU LCP-1C

THRU LCP-1C

THRU LCP-1C

THRU LCP-1C

HH

N41C:16,18

THRU LCP-1C

20 22

N41C:20,22

THRU LCP-1C

21 23

HH

THRU LCP-1C

HH

N41C:21,23

THRU LCP-1C

W06

N41C:15

W07

W06

N41C:11

W05 W05 W05

NOTE 5

NOTE 3

HH

HH

HH

HH

1"C, 10's

NOTE 2

1"C, 10's

NOTE 2

1"C, 10's

NOTE 2

HH

1"C, 10's

NOTE 2

HH

1"C, 10's

NOTE 2

NOTE:

REFER TO PHASING

NOTES ON SHEET E-003

1"C, 10's

NOTE 2

EX

W05

N41C:17,19

NOTE 4

NOTE 4

NOTE 2 (TYP)

NOTE 2 (TYP)

W0713

NOTE 1 (TYP)

NOTE 1 (TYP)

NOTE 1 (TYP)

NOTE 1 (TYP)

NOTE 1 (TYP)

NOTE 1 (TYP)

NOTE 1 (TYP)

NOTE 1 (TYP)

10's 10's

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

SCALE: 1"=30'-0"

20' 40' 60' 877

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:1

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

1" = 30'-0"

SCALE: 1" = 30'-0"

ES103

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

S

IT

E P

L A

N

L

IG

H T

IN

G

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909487

MLB AL MBA

ELECTRICAL SITE PLAN - LIGHTING

JAS

1. REFER TO DETAIL A1/ES502 FOR POLE FOUNDATION DETAILS.

2. DIRECT BURY SITE LIGHTING BRANCH CIRCUITING A MINIMUM OF 24" BELOW FINISHED GRADE.

3. ROUTE CONDUIT, VIA DIRECTIONAL BORE, IN SAME VICINITY AS SECURITY CAMERA AND POWER CONDUITS WHEN

CROSSING ALASKA STREET. REFER TO SHEET CU102 FOR ADDITIONAL INFORMATION.

4. SET HANDHOLE IN PLACE UNDER PHASE 2. PROVIDE 5'-0" OF EXTRA CABLE LENGTH AND MAKE SAFE FOR

EXTENSION TO LIGHT POLES IN PHASE 3.

5. ROUTE CONDUIT, VIA DIRECTIONAL BORE, ACROSS ALASKA STREET. REFER TO SHEET CU102 FOR ADDITIONAL

INFORMATION.

PLAN

NORTH

1. REFER TO DETAIL A1/ES502 FOR POLE FOUNDATION DETAILS.

2. DIRECT BURY SITE LIGHTING BRANCH CIRCUITING A MINIMUM OF 24" BELOW FINISHED GRADE.

CONSTRUCTION LIMITS PHASE 3 NOTES: CONSTRUCTION LIMITS PHASE 2 NOTES:

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

J J

EMERGENCY SHUT-

DOWN BUTTON, 48"AFG

CHILLER CH-1

480V, 3PF, 264FLA

CHILLER CH-2

480V, 3PH, 264FLA

RADIATOR END

TRANSFORMER T-1.

SEE DETAIL A3/ES503

GENERATOR SET

AND ENCLOSURE.

SEE DETAIL A1/ES503

U S

CRU-1

480V, 3PH, 9.6FLA

LOAD BANK QUICK CONNECT. SEE

EP601 FOR ADDITIONAL INFORMATION

4HVAC:

14,16,18

NF

NF

LOAD BANK FAN. NEMA 4X,

STAINLESS STEEL

ENCLOSURE. SEE NOTE 3.

(2) 1"C TO ATS's

(CONTROLS). DIRECT

BURY 40" BFG.

(2) 1"C TO REMOTE ANNUNCIATOR

PANEL (RAP) IN RM 1C03. DIRECT

BURY 40" BFG

WP,SS

NOTE 4

T

4HVAC:

19,21,23

WPG

WPG

WPG

WPG

NOTE 5

JACKET HEATER

208V,1PH,22.8A

BATTERY CHARGER

120V,12.5A

1,3

REFER TO SINGLE LINE

DIAGRAM (SHEET

EP601) FOR CONDUIT

AND WIRE SIZE. DIRECT

BURY 40" BFG.

NOTES 1 & 2

LS21A1:

1,3

NOTES 1 & 2

NOTES 1 & 2

LS21A1:6

SLD

WP

U S

U S

U S

LS21A1

LS21A1:510's

SLD.

40" BFG

NEMA 4X, STAINLESS

STEEL ENCLOSURE.

NOTE 6

N21A1:

25,29

8's

NOTE 6

WP,SS

NF

SLD. NOTE 7

MSWGR:3

NF

WP,SS

SLD. NOTE 7

MSWGR:2

SLD

T-1

G E

N E

R A

T O

R S

E T

W08

W08

W08

W08

W08

W08

DP-480-LS:24

WP

NOTE 8 (TYP)

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

4' 8' 16'

SCALE: 1/8"=1'-0"

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:1

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

As indicated

ES401

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E N

LA

R

G E

D S

IT

E

P L A

N S

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909488

MLB RMA MBA

JAS

SCALE: 1/4" = 1'-0"

ENLARGED SITE PLAN - MECH YARD POWER

A1 SCALE: 1/8" = 1'-0"

ENLARGED SITE PLAN - MECH YARD LIGHTING

A4

NOTES:

1. SEE ES102 FOR DUCTBANK CALLOUT.

2. SEE SHEET ES102 FOR CONTINUATION.

3. PROVIDE A 2" DIA IMC NIPPLE, 6" LONG, WITH THREADED CAP ON UNDERSIDE

OF SWITCH FOR CABLE ACCESS DURING LOAD BANK TESTING.

4. PROVIDE CONTROL WIRING AND CONDUIT FOR GENERATOR EMERGENCY

SHUT-OFF SIZED IN ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS.

5. POWER CONNECTION POINTS FOR BATTERY CHARGER AND JACKET HEATER.

COORDINATE ACTUAL LOCATION WITH MANUFACTURER AND CONCRETE PAD

INSTALLER.

6. 20A-1P, 10KAIC RATED ENCLOSED CIRCUIT BREAKER IN NEMA 4X ENCLOSURE,

MOUNTED 60"AFG AND CONNECTED TO HEAT TRACING CIRCUIT ASSOCIATED

WITH CHILLER UNIT. SEE SHEET M-412 FOR ADDITIONAL INFORMATION.

7. ROUTING OF CHILLER FEEDER IS SHOWN ON SHEET ES102.

8. COORDINATE INSTALLATION OF LUMINAIRE WITH WALL CONSTRUCTION

SHOWN IN DETAIL A1/A-173.

0 2' 4' 8'

SCALE: 1/4"=1'-0"

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

DUCTBANK SCHEDULE

4 - 5" CONDUITS

#1

#2

A1 3 - 1/C #2/0 (15kV) - LOOP IN

SPARE

A2 12 - 4" CONDUITS

#1

#2

#3

#4

#5

#6

#7

#8

#9

#10

4 - 500 KCMIL

4 - 500 KCMIL

4 - 500 KCMIL

4 - 500 KCMIL

4 - 500 KCMIL

4 - 500 KCMIL

4 - 500 KCMIL

4 - 500 KCMIL

#11

#12 SPARE

4 - 500 KCMIL

SPARE

SPARE

#3

#4

3 - 1/C #2/0 (15kV) - LOOP OUT

SPARE

A4 4 - 4" CONDUITS

#1

#2

#3

#4 SPARE

SPARE

4 - 500 KCMIL

4 - 500 KCMIL

NOTES:

1. PROVIDE MINIMUM COVER OF 42" UNLESS OTHERWISE NOTED ON THE

SITE PLANS.

M

IN

4"

3" M

IN

(T Y

P

SEE DUCTBANK SCHEDULE THIS

SHEET

5" 3" MIN.

(TYP.)

21" MIN.

#1 #2

#3 #4

PROVIDE DUCT MARKER MAGNETIC

TAPE AT 12" BELOW GRADE WITH

"ELECTRIC" LOGO

GRADE

SELECT BACKFILL PLACED AND

COMPACTED TO AT LEAST 90% OF

MAXIMUM DENSITY

CONCRETE ENCASEMENT

ANCHORING RODS

@ 60" O.C.

#18 GA. GALV. WIRE (WIRE

FROM TOP TO BOTTOM)

BASE SPACERS @ 60"

O.C.

4"

PROVIDE DUCT MARKER MAGNETIC

TAPE AT 1' BELOW GRADE WITH

"ELECTRIC" LOGO

SELECT BACKFILL PLACED AND

COMPACTED TO AT LEAST 90%

OF MAXIMUM DENSITY

CONCRETE ENCASEMENT

ANCHORING RODS @ 10'

O.C.

#18 GA. GALV. WIRE (WIRE

FROM TOP TO BOTTOM)

BASE SPACERS

@ 60" O.C.

5" 3" MIN.

(TYP.)

4"

3" MIN.

(TYP.)

4"

M

IN

SEE DUCTBANK SCHEDULE FOR

CONDUIT SIZE AND CABLE

GRADE

#1 #2 #3 #4

#5 #6 #7 #8

#9 #12

3" MIN.

(TYP.)

#10 #11

35" MIN.

V A

R

IE

S . S

E E

N O

T E

4"

3" M

IN

(T Y

P

SEE DUCTBANK SCHEDULE THIS

SHEET

5" 3" MIN.

(TYP.)

21" MIN.

#1 #2

#3 #4

PROVIDE DUCT MARKER MAGNETIC

TAPE AT 12" BELOW GRADE WITH

"ELECTRIC" LOGO

GRADE

SELECT BACKFILL PLACED AND

COMPACTED TO AT LEAST 90% OF

MAXIMUM DENSITY

CONCRETE ENCASEMENT

ANCHORING RODS

@ 60" O.C.

#18 GA. GALV. WIRE (WIRE

FROM TOP TO BOTTOM)

BASE SPACERS @ 60"

O.C.

4"

4/0 BARE GROUND. CONNECT TO

GROUND RODS IN MANHOLES

AND AT TRANSFORMER PAD

NOTE: WHERE DUCTBANK ROUTES UNDER PAVED SURFACES, REFER TO CIVIL DETAILS.

A

B

C

D

1 2 3 4

1 2 3 4

A

B

C

D

SCALE:

PROJECT NO:

CONSTR CONTR NO:

NAVFAC DRAWING NO:

SHEET: OF

FIRE PROTECTION

CHIEF ENG/ARCH

BRANCH MGR

PM/DM

DES DRW CHK

SATISFACTORY TO DATE

ACTIVITY

FOR COMMANDER NAVFAC

APPROVED

A/E INFO

SEAL

S Y

M D

E S

C R

IP

T

IO

N

D A

T E

A P

P R

08/19/2024

P A

R R

IS

I S

L A

N D

S

C M

C R

D

P A

R R

IS

I S

L A

N D

N A

V A

L S

T A

T

IO

N

N O

R F

O L

K V

A

D E

P A

R T

M E

N T

O F

T H

E N

A V

Y N

A V

A L

F A

C

IL

IT

IE

S E

N G

IN

E

E R

IN

G

S Y

S T

E M

S C

O M

M A

N D

M

ID

L A

N T

D C

C O

R E

MT / SVR

EJA

DSN

Approved by Jason J. Root, NAVFAC / MFPO VIA SAT-TO Memo Dated 08/08/2024 Tracey Bond, Defense Health Agency VIA SAT-TO Memo Dated 08/19/2024

/2

/2

:1

:2

P

M

C

U s e rs \r ic k .a n a s ta s io

\D o c u m e n ts

\2

-E ri c k .a n a s ta s io

.r v t

As indicated

ES501

2021-003

D E

N T

A L

C L

IN

IC

R E

P L

A C

E M

E N

T

E

LE

C T

R

IC

A L

S

IT

E D

E T A

IL

S

N A

V A

L F

A C

IL

IT

IE

S

E N

G

IN

E E

R

IN

G C

O M

M A

N D

M

ID

-A T

L A

N T

IC

12909489

MLB RMA MBA

JAS

SCALE: NOT TO SCALE

GENERATOR FEEDER (2X2) DUCT BANK

A4SCALE: NTS

SECONDARY POWER (3X4) DUCT BANK

A2SCALE: NOT TO SCALE

PRIMARY POWER (2X2) DUCT BANK

A1

M S

O R

G

A N L E E BAR

N E

A AL A B A M

L DI C E N S E

NO. 22474

STYLE

DUCT ENTRANCE

12" x 12" x 10" DEEP

SUMP

6"

A

6"

A

6"

B

6"

PLAN

7/8" ∅ PULLING-IN IRON

FOR MANHOLE FRAME & COVER, SEE FED. SPEC.

A-A-60005 FIG. 4, SIZE 28 AND FIG. 12, SIZE 28

RESPECTIVELY

BRICK COLLAR LINED UP WITH

CEMENT MORTAR

DUCT ENTRANCE

LAP REINF. 24" (TYP.)

WATERSTOP AT ALL

CONSTR. JTS. (TYP.)

7/8" ∅ PULLING-IN IRON

#5 REINF. AT 6" EW TOP,

SIDES & BOTTOM

SLOPE 1:40 TO

SUMP

GROUND ROD & CLAMP

SECTION A-A

NOTES:

1. FOR DETAILS OF CABLE RACKS, DUCT

ENTRANCE AND PULLING-IN IRONS, SEE

PLATE UG-7.

2. MINIMUM CONCRETE COMPRESSIVE

STRENGTH MUST BE 3000 PSI. C (AT HIGH PT.)

6'-6" 6'-6"8'-0"

6'-0"

B

MANHOLE DIMENSIONS

A

6'-0" 6'-0"2

TYPE

STANDARD ELECTRICAL MANHOLE (NONTRAFFIC) TYPES 1 & 2

JUNE 2002SKETCH DATE UG-1

A

1'-0"6"

6"B

C

6"

10"

8"

12" x 12" x 10" DEEP SUMP

8"

A

AA

7/8"∅ PULLING-IN IRON 8"

DUCT ENTRANCE. LOCATION TO BE AS

INDICATED

8"B

8"

PLAN

CONCRETE OR BLACK TOP

ROADWAY

#5 @ 6" EW, T&B

#4 @ 6" EW EF

7/8"∅ PULLING-IN IRON

8"

SLOPE 1:40 TO SUMP

C

B

WATERSTOP AT ALL

CONSTR. JTS. (TYP.)

#4 @ 6" T&B 10"

FOR MANHOLE FRAME & COVER, SEE FED. SPEC.

A-A-60005, FIG. 1, SIZE 30A AND FIG. 8, SIZE 30A,

RESPECTIVELY

BRICK COLLAR LINED UP WITH CEMENT

MORTAR

6" MIN.

DUCT ENTRANCE

LAP REINF. 24" (TYP.)

GROUND ROD & CLAMP

NOTES:

1. MANHOLE AND COVERS ARE DESIGNED FOR

MAXIMUM WHEEL LOAD IN ACCORDANCE WITH

AASHTO HS20-44.

2. FOR DETAILS OF CABLE RACKS, DUCT ENTRANCE

AND PULLING-IN IRONS, SEE PLATE UG-7.

3. MINIMUM CONCRETE COMPRESSIVE STRENGTH

MUST BE 3000 PSI.

SECTION A-A

MANHOLE DIMENSIONS

C (AT HIGH PT.)BATYPE

6'-0" 6'-0" 8'-0"

6'-0" 6'-6" 6'-6"

STANDARD ELECTRICAL MANHOLE (TRAFFIC) TYPES 3 & 4

STYLE UG-2JUNE 2002SKETCH DATE

STAINLESS STEEL

HEX BOLT AND

WASHER

PULL SLOT

SKID

RESISTANT

SURFACE

CONCRETE RING

AROUND BOX

10"

BOX AND

COVER6"

6"

COMPACTED

EARTH

6"

CRUSHED ROCK

SECTIONAL

BOX WHEN

REQUIRED HANDHOLE SIZINGTYPE

12" X 12" X 24" DEEP

12" X 18" X 24" DEEP

12" X 24" X 24" DEEP

24" X 36" X 24" DEEP

30" X 48" X 24" DEEP

HANDHOLE REQUIREMENTS

1. PROVIDE A POLYMER CONCRETE REINFORCED HOUSING WITH A HEAVY WEAVE FIBERGLASS REINFORCING WITH

COMPRESSIVE STRENGTH OF NO LESS THAN 10,000 PSI.

2. COVER AND BOX MUST WITHSTAND A SERVICE LOAD OF NO LESS THAN 15,000 LBS OVER A 10" x 10" AREA.

3. PROVIDE STAINLESS STEEL BOLTS AND INSERTS.

4. PROVIDE WITH (2) 2 1/2" MOUSEHOLES.

5. PROVIDE LABEL "ELECTRICAL" FOR POWER HANDHOLES OR "TELEPHONE" FOR TELEPHONE HANDHOLES, OR AS INDICATED.

STANDARD ELECTRICAL HANDHOLE (NONTRAFFIC)

(COMPOSITE/FIBERGLASS) TYPES 5, 6, 7, 8 & 9

JUNE 2002SKETCH DATE STYLE UG-6

LABEL

ALTERNATE METHOD

L

1"∅ NUT

3" CONCRETE WALL

13/16"

1 1/2" (MIN)

1 1/4"∅ SLEEVE LOCKWASHER

2 1/2"∅ WASHER

6 1/2" X 2 1/2" X 3/16" PLATE

8 3/8"

7/8"∅

9" 3/16"

FILLET WELD

2 1/2" RAD

1"∅ U-BOLT

C

4"

CAST IN PLACE

NOTE

ALL METAL…