Copy of 5100195_Control-Repeater Panel M 4.3_M_EN_2018_H.pdf

1(5) DATA SHEET

The specifications described herein are subject to change without notice. Data sheet no. 5100195_Control-Repeater Panel M 4.3_M_EN_2018_H www.consilium.se

Control/Repeater

Panel M 4.3 Part no. 5100195

System: Salwico Cargo, Salwico Cruise, Salwico LNG,Salwico Offshore, Salwico Ro/Pax, Salwico Workboat, Salwico Yacht, Salwico Navy, OEM Extinguish

General Description The Control/Repeater Panel M 4.3 is a control panel with a 4.3" graphical colour display used to manage and supervise a system. Control/Repeater Panel M 4.3 mounts on any flat surface independently from a fire alarm cabinet.

Control/Repeater Panel M 4.3 is equipped with communication buses for connecting to the system, and it provides the following features:

• A backlit 4.3" graphical colour display

• Alarm buzzer

• LED status indicators

• Backbone Bus Interface

• Ethernet connection

• RS-422/RS-485 interface

• RS-232/RS-485 interface

• Three USB interfaces

• Two configurable powered I/Os

• Two programmable relay outputs

Refer to the User Guide for more information on operating Control/Repeater M 4.3.

For details on assembling a system and definitions of common system terms, refer to the Installation Manual.

Part No.

Control/Repeater M 4.3 Cargo 5100195-20A

Control/Repeater M 4.3 Ro/Pax 5100195-30A

Control/Repeater M 4.3 Workboat 5100195-40A

Control/Repeater M 4.3 Yacht 5100195-50A

Control/Repeater M 4.3 Cruise 5100195-80A

Data Operating voltage range

19-30 VDC

Current consumption (at 24V)

Normal 100 mA Max. 270 mA

Ingress protection IP22

Operating temperature range

-5°C to +55°C

Weight 1250g

Display 4.3", 480×272 pixels, TFT

Ethernet 10/100 Mbit, autosense

USB Host USB 1.1 1 in front, 1 on back

USB Device USB 1.1 1 on back

Relays rating Max. 30 VDC, 500 mA

I/O 70 (as input) 24 VDC 5-70 mA

I/O 70 (as output) 24 VDC Max. 70 mA

Cable terminals 2.5 mm²

SD Memory (Optional)

Certified according to ROHS

EN 54-2 (1999/A1:2006)

EN 60945

2531/yy yy = year of production

Indicators Control/Repeater Panel M 4.3 indicators display system status. Refer to the User Guide for more information.

DATA SHEET 2(5)

The specifications described herein are subject to change without notice. Data sheet no. 5100195_Control-Repeater Panel M 4.3_M_EN_2018_H www.consilium.se

Hot-Swap Replacement of the Module Replace this module following these steps:

1. Remove all cable connections form the module.

2. Address the Module DIP-Switch settings using old module as a guide.

3. Move the Micro SD memory from the old module, if installed, to new module.

4. Plug in all cable connections back.

Address Switch This switch (see SW2 in figure Connection board) identifies modules in the system and sets the function.

Control modules can serve as Bus Masters, i.e., operate in Controller Mode or in Managed Mode, for example repeaters and protocol converters. Address 1 and 2 are dedicated for control modules in Controller Mode. One control module per central shall be set in Controller Mode. If the system shall be reduntant it is required to have a second control module, also set in Controller Mode. Modes for Managed and Controller are set with DIP switches as described in the following table:

Managed Mode Controller Mode

DIP 8 Controller Mode (off) Controller Mode (on)

DIP 7 Module Address (3-125)

Spare

DIP 6 Master (on/off)

DIP 5 Central Address (1-30)

DIP 4

DIP 3

DIP 2

DIP 1

Control Modules have two different modes of operation, as determined by their DIP settings (normally pre-set from factory):

Controller Mode

Single Central System:

Central 1 Primary (automatically module address 1)

Central 1 Secondary (optional) (automatically module address 2)

Multi Central System:

Central 1 Primary (automatically module address 1)

3(5) DATA SHEET

The specifications described herein are subject to change without notice. Data sheet no. 5100195_Control-Repeater Panel M 4.3_M_EN_2018_H www.consilium.se

Central 1 Secondary (optional) (automatically module address 2)

Central 30 Primary (automatically module address 1)

Central 30 Secondary (optional) (automatically module address 2)

Managed Mode

Module Address 3-125

Connections Control/Repeater Panel M 4.3 mounts outside of the central. Using ribbon cables, connect the Control/Repeater Panel M 4.3 to Terminal M (pre-fitted inside the Control/Repeater Panel M 4.3 casing, see Module Dimensions (mm)). All Control/Repeater Panel M 4.3 connections are made on the Connection board, located at the back of the front panel. See figure Connection board.

Figure 1. Connection board

Connector no. Function Description

P4 Connection to Terminal M 20-pol. Flat Cable *

P5 Connection to Terminal M 10-pol. Flat Cable *

P6 Door Switch

P7 Ethernet

P8 Type A/ Host USB

P9 USB Expansion Board

P10 Type B/ Device USB

P11 External Buzzer (24V)

* See illustration below for connection to Terminal M.

DATA SHEET 4(5)

The specifications described herein are subject to change without notice. Data sheet no. 5100195_Control-Repeater Panel M 4.3_M_EN_2018_H www.consilium.se

Figure 2. Terminal M

* Do not connect to this terminal!

** Terminal 23 is signal ground for channel 4, marked "GNDB" on PCB.

*** Terminal 38 is signal ground for channel 3, marked "GNDA" on PCB.

RS485 Termination of Serial Interface 3 & 4 For RS485 termination of channel 3 and channel 4 the built-in resistor (120 ohm) can be activated with the RS485 DIP switch located on the Connection board (see figure in section Connections).

For recommendations and examples on RS485 termination, refer to the Installation Manual.

Table 1. DIP switch for RS485 termination

DIP

Switch No.

Description ON OFF

1 Channel 3 Active Deactivated

2 Channel 4 Active Deactivated

5(5) DATA SHEET

The specifications described herein are subject to change without notice. Data sheet no. 5100195_Control-Repeater Panel M 4.3_M_EN_2018_H www.consilium.se

Module Dimensions (mm)

Mounting Dimensions (mm)