099113_01_00 Acrylic Finish Submittal_EGI.pdf

F.H. PASCHEN, S.N. NIELSEN & ASSOCIATES LLC

1344 La France Street, NE Suite 2, Atlanta, GA 30307

p. 404.942.1307 f. 404.228.4050 | www.fhpaschen.com

SUBMITTAL COVER SHEET

Fill out items 1 through 4 below and submit product data sheet, sample, shop drawing, or other items submitted to the

Owner/Architect/Engineer. Each submittal line item shall have its own Submittal Cover Sheet.

Project Name: KSU Clendenin Building Envelope Repairs Contractor: FH Paschen

Project Manager: Justice Hill

Address:

739 Trabert Ave NW

Atlanta, GA 30318

Phone: 770-584-4267

Architect/Engineer: RJ Wells – Epsten Group Owner: Kennesaw State University

Owner Project

Manager:

Emmanuel Bertrand - KSU

1. Date: ______7/19/24 _____

2. Submitted Item: ________DPR Standard Acrylic Finish Submittal

3. Manufacturer: ____Parex___

4. Notes:

Contractor’s Stamp Owner/ Engineer/ Architect Stamp

No exception taken.

Revise as noted. Do not resubmit. See Notes above.

Revise as noted. Resubmit. See Notes above.

Rejected. See Notes above.

Checking of submittals is only for general conformance with the design concept of the Project and general compliance with the information given in Contract Documents. Any action shown is subject to the requirements of the Drawings and Specifications. Contractor is responsible for dimensions to be confirmed and correlated at the job site, quantities, information that pertains solely to the fabrication processes or to techniques of construction, coordination of the work of all trades, and the satisfactory performance of his work.

By: Date:

EGI General Comments

1. This product is part of a whole stucco assembly, the acceptance of this product is contingent on the use of other compatible AWRB and stucco components. Review comments on other stucco-related submittals prior to procurement.

2. Product substitutions are not accepted unless explicitly accepted in writing by the manufacturer.

3. Finish texture and color to be selected by the Owner

REVIEWED NO

COMMENT

REVISE &

RESUBMIT

BY

SUBMITTAL#

DATE

SPEC

RJWells 7/24/2024

099113-01-00 099113 epstengroup 101 Marietta Street NW Suite 2600 Atlanta, Georgia 30303 t 404 577 0370 epstengroup.com

Disclaimer: Review is for systems commissioning only. Submittal acceptance or rejections above are recommendations only. Final approval is the responsibility of the Design Professional.

530 Swirl Fine 531 Swirl Coarse 532 Multi-texture

533 Sand Smooth 534 Sand Fine 535 Sand Coarse

DESCRIPTION

n 100% Acrylic-based textured finish n DPR (Dirt Pick-up Resistance) chemistry n Integrally colored with high-quality pigments n Exceeds ASTM and ICC

Acceptance Criteria

USES

Exterior or interior finish coat over:

n Parex CI Systems n Properly prepared masonry, stucco, and concrete surfaces n Interior application over drywall, plaster, or properly prepared masonry or concrete

COMPOSITION

n Binder base: 100% acrylic polymer with surface-hardening property.

n Aggregate: Pure crushed marble, rust-free.

n Water-based: VOC–compliant n Pigment base: Titanium dioxide.

n Color: ParexUSA standard colors or tinted to desired custom color. Meets SCAQMD Rule 1113 when using ParexUSA Non-VOC Colorants

CONTAINER

65 lb (29.5 kg) net weight in plastic pails.

n Storage: Protect from direct sunlight and freezing at all times.

n Do not stack pails more than 3 pails high.

n Shelf life: Reference ParexUSA Expiration Date of Products Technical Bulletin

*Tested with Parex Base Coat

DPR Standard Acrylic Finishes

532 MULTI TEXTURE

535 SAND COARSE

530 SWIRL FINE

533 SAND SMOOTH

531 SWIRL COARSE

534 SAND FINE

Test Method Criteria Results

Abrasion Resistance* ASTM D968 No cracking or loss of film integrity at 528 quarts (500 L) of sand

Pass @ 1000 Liters

Accelerated Weathering

ASTM G153

(Formerly

ASTM G 23)

No deleterious effects at 2000 hours when viewed under 5x magnification

Pass

Flexibility (Mandrel Bend)

ASTM D522,

Method B

No Requirement 1” diameter @ -4ºF

Freeze/Thaw Resistance * ASTM E 2485 No deleterious effects at 10 cycles when viewed under 5x magnification

Pass @ 60 cycles

Mildew Resistance* ASTM D 3273 No growth supported during 28 day exposure period

Pass @ 35 days

Mildew Resistance* MIL 810 B 508 No growth 28 days

Moisture Resistance* ASTM D2247 No deleterious effects at 14 day exposure Pass 28 days

Salt Fog Resistance* ASTM B117 No deleterious effects at 300 hours Pass @ 900 hrs

Scrub Resistance ASTM D2486 No Requirement Pass 10,000 Cycles

Surface Burning Characteristics

ASTM E84

Individual components shall each have a flame spread <25, and smoke developed < 450

Flame Spread: 0 to 15 Smoke Developed: 0 to 15

Water Vapor Transmission

ASTM E 96

Procedure B

Vapor Permeable Permeable

VOC

EPA Reference Test Method 24

US EPA, South Coast AQMD and Greenseal Standard

8 g/L

1st Pass

2nd Pass n ParexUSA recommends the use of primers to enhance the appearance and uniformity of the finish, improved coverage, and decrease the chance of efflorescence. This is especially true when using dark colors or finishes with a large aggregate. If specified, prime with ParexUSA Primer or Variance VariPrime Sanded, refer to Product Data Sheet.

n For additional options, contact ParexUSA Technical Services Department.

MIXING

n Use clean equipment for mixing and preparation.

n Stir to obtain a homogeneous consistency using a heavy-duty 1/2-in.

(13mm) drill with a rust free paddle at 400–500 rpm. Avoid air entrainment.

n Add the amount of water needed to achieve finish texture. To avoid color variations, add the same amount of water to each pail of finish as up to 16 oz (0.5 L).

APPLICATION

n Read the entire label before using this product n Always maintain a wet edge and work to corners or joints. For best color consistency, use finish with the same batch number within a wall section.

For more information, see Technical Bulletin: “Boxing Acrylic Finishes”.

n Keep container closed when not in use.

n Use a clean stainless steel trowel and apply a uniform coat the thickness of the largest aggregate size of the finish.

n Texturing 532 Multi-Texture Finish:

Use a clean stainless steel trowel and apply a uniform coat the thickness of the largest aggregate size of the finish and allow to completely dry before applying the second coat. Proper drying in between coats is crucial. If the second coat is applied over a wet first coat, the material will dry as a one thick coat and be more prone to cracking. After the first pass has dried (typically 3-4 hours in 75ºF, 50% RH) apply a second coat of 532 Multi- Texture, using tools and techniques necessary to obtain the desired texture.

The maximum thickness within the applied texture must not exceed 3/16

in. (5mm) with average thickness not more than 1/8 in. (3mm).

n Texturing 530 Swirl, 531 Swirl Coarse, 534 Sand Fine, and 535 Sand Coarse Finishes: Use a clean plastic float or stainless steel trowel.

A plastic float will roll the large aggregates more than a stainless steel trowel , and may cause swirling. Continuously dry clean the plastic float or steel trowel while texturing.

Use consistent pressure and motion to achieve the desired texture.

n Texturing 533 Sand Smooth Finish

- Optional: Level stucco brown coats with any Parex 121 Base Coat & Adhesive and let dry prior to finish application.

- 533 Sand Smooth Finish cannot generally be floated. Texture will be “as trowelled.”

- 533 Sand Smooth Finish can be trowelled smooth to simulate the texture of limestone.

- For smoothest application, apply in two tight coats. Allow first coat to dry enough that it will not be disturbed during application of the second coat.

When second coat is partially dry, trowel to desired smoothness. Light, consistent misting with water during smoothing will increase smoothness. Variations in color tint and smoothness should be expected.

n Spray application: To achieve consistent texture, spray application must use consistent motion, pressure, distance and spray angle. A job-site mock up for spray application is advised.

LIMITATIONS

n Ambient and surface temperature must be

40ºF (4ºC) or higher during application and drying time. Provide supplemental heat and protection from precipitation as needed.

n Use only on surfaces that are sound, clean, dry, unpainted, and free from any residue that might affect the ability of the finish to bond to the surface.

n Application in direct sunlight in hot weather may adversely affect aesthetics.

n ParexUSA is not responsible for color correctness after finish has been applied.

WARNING

n Read complete Warning information printed on product container prior to use. For medical emergency information, call 1-800-424-9300.

n For more information on handling this product refer to its Safety Data Sheet (SDS). The most current SDS and Product Data Sheet (PDS) can be found on our website.

n This Product Data Sheet has been prepared in good faith on the basis of information available at the time of publication. It is intended to provide users with information about the guidelines for the proper use and application of the covered product(s) under normal environmental and working conditions. Because each project is different, ParexUSA, Inc. cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions.

COVERAGE

Depending on the condition of the substrate and method of application, approximate coverages per pail are:

530 Parex Swirl Fine Aggregate size: 1.5mm 120–135 ft2 (11–12.5 m2)

531 Parex Swirl Coarse Aggregate size: 3.0mm 70–95 ft2 (6.5–9 m2)

532 Parex Multi-Texture 60–150 ft2 (6–14 m2) Coverage varies due to texture.

533 Parex Sand Smooth Aggregate size: 0.5mm 280–300 ft2 (26–28 m2)

534 Parex Sand Fine Aggregate size: 1.0mm 150–165 ft2 (14–15 m2)

535 Parex Sand Coarse Aggregate size: 1.5mm 90–110 ft2 (8.4-10.2 m2)

DRYING TIME

24-48 hours under normal conditions.

High humidity and low temperatures extend drying time.

CLEAN UP

Water soluble prior to drying. Clean tools and containers with water prior to drying.

SURFACE PREPARATION:

n Remove surface contaminants such as dust or dirt without damaging the substrate.

n For previously painted surfaces, all loose and chalking paint must be removed, and glossy surfaces dulled.

n Portland Cement Plaster must be clean and cured a minimum of 7 days or in accordance with Parex Armourwall Specifications.

n New concrete, stucco and masonry must be clean and cured a minimum of 28 days.

n Check concrete surfaces for alkalinity and treat. Any form-release agents or bond breakers must be removed.

n Uneven concrete or masonry can be leveled with a Parex 121 Base Coat & Adhesive or other suitable, compatible product.

n For interior drywall, prepare as for painting.

Parex USA, Inc., a California Corporation 4125 E. La Palma Ave., Suite 250 Anaheim, CA 92807 www.parexusa.com 866-516-0061 Tech Support: 800-226-2424

© Parex USA, Inc. August 2018 • PX DPRF DS 0818