092423_01_00 Preblended Stucco Submittal_EGI.pdf

F.H. PASCHEN, S.N. NIELSEN & ASSOCIATES LLC

1344 La France Street, NE Suite 2, Atlanta, GA 30307

p. 404.942.1307 f. 404.228.4050 | www.fhpaschen.com

SUBMITTAL COVER SHEET

Fill out items 1 through 4 below and submit product data sheet, sample, shop drawing, or other items submitted to the

Owner/Architect/Engineer. Each submittal line item shall have its own Submittal Cover Sheet.

Project Name: KSU Clendenin Building Envelope Repairs Contractor: FH Paschen

Project Manager: Justice Hill

Address:

739 Trabert Ave NW

Atlanta, GA 30318

Phone: 770-584-4267

Architect/Engineer: RJ Wells – Epsten Group Owner: Kennesaw State University

Owner Project

Manager:

Emmanuel Bertrand - KSU

1. Date: ______7/19/24 _____

2. Submitted Item: ________Preblended Stucco

3. Manufacturer: ____Spec Mix___

4. Notes:

Contractor’s Stamp Owner/ Engineer/ Architect Stamp

No exception taken.

Revise as noted. Do not resubmit. See Notes above.

Revise as noted. Resubmit. See Notes above.

Rejected. See Notes above.

Checking of submittals is only for general conformance with the design concept of the Project and general compliance with the information given in Contract Documents. Any action shown is subject to the requirements of the Drawings and Specifications. Contractor is responsible for dimensions to be confirmed and correlated at the job site, quantities, information that pertains solely to the fabrication processes or to techniques of construction, coordination of the work of all trades, and the satisfactory performance of his work.

By: Date:

REVIEWED NO

COMMENT

REVISE &

RESUBMIT

BY

SUBMITTAL#

DATE

SPEC

RJWells 7/24/2024

092423-01-00 092423 epstengroup 101 Marietta Street NW Suite 2600 Atlanta, Georgia 30303 t 404 577 0370 epstengroup.com

Disclaimer: Review is for systems commissioning only. Submittal acceptance or rejections above are recommendations only. Final approval is the responsibility of the Design Professional.

G1.08 STUCCO ASSEMBLY-KRAK-SHIELD-STEEL FRAME

general c o HE n KRAK-SHIELD o WATERMASTER

EGI General Comments

1. This product is part of a whole stucco assembly, the acceptance of this product is contingent on the use of other compatible AWRB and stucco components. Review comments on other stucco-related submittals prior to procurement.

2. Product substitutions are not accepted unless explicitly accepted in writing by the manufacturer.

3. Contractor to verify if this product refers to the primer coat, finish coat, or other. See snapshot assembly from Parex for reference.

1-888-SPECMIX

DIVISION

MASONRY PRODUCTS09 DIVISION

STUCCO

SPEC MIX® Scratch and Brown Preblended Stucco is a dry, preblended cement based stucco basecoat to be used as the scratch and/or brown coat in a three-coat stucco application.

SPEC MIX Scratch and Brown has a custom blended sand gradation that increases the walls flexural strength while reducing cracking and crazing. SPEC MIX Scratch & Brown is computer batched for consistency and performance that is unmatched by traditional field mixed stucco.

The custom sand gradation also provides excellent workability and finishing properties for the applicator over a traditional field-mixed source.

SPEC MIX Scratch and Brown Preblended Stucco can be installed over framed wall construction that includes a solid backing such as fiberboard, gypsum sheathing and wood based sheathing.

SPEC MIX Scratch and Brown Stucco can also be applied over concrete and masonry substrates.

SPEC MIX Scratch and Brown Preblended Stucco is produced under strict manufacturing standards, and complete quality control measures are implemented with each batch. A digital printout displaying the proper proportions per batch may be kept as a permanent record.

Submittals are available upon request for certification to applicable ASTM standards.

Excellent Workability. Reduced Shrinkage.

SCRATCH & BROWN

PREBLENDED STUCCO

TYPICAL MATERIALS

PORTLAND CEMENT

HYDRATED LIME

SAND

PERFORMANCE ADMIXTURES

(SU-01)

SPEC MIX PRODUCTS ARE PRODUCED BY ITS MANUFACTURING FACILITIES THROUGHOUT THE U.S. AND CANADA. EACH MANUFACTURER ADHERES TO A STRICT QUALITY ASSURANCE PROGRAM TO ENSURE COMPLETE QUALITY CONTROL IN EVERY BATCH.

© 2020 SPEC MIX

1230 EAGAN INDUSTRIAL RD, STE160, EAGAN, MN 55121 T 888-773-2649 F 651-454-5315 WWW.SPECMIX.COM

TECHNICAL SUPPORT

• CONTACT YOUR LOCAL SPEC MIX® MANUFACTURER

• VISIT WWW.SPECMIX.COM

• CONTACT SPEC MIX®

PHONE: 888-773-2649 FAX: 651-454-5315

INSTALLATION/APPLICATION

SPEC MIX Scratch and Brown Preblended Stucco is designed for use over galvanized, expanded metal lath or solid base surfaces such as masonry or precast concrete. The material can be hand applied or machine sprayed. Installation of stucco over these surfaces shall be in accordance with ASTM C 926, and all applicable building codes.

Dampen all surfaces to receive stucco prior to application. An expansion joint should be installed at dissimilar materials.

Stucco shall be used and placed in final position within one hour after initial mixing.

Variation of water content and retempering will affect strength, consistency and uniformity.

SPEC MIX products must be kept dry, covered and protected from weather and other damage.

SIZES AND EQUIPMENT

SPEC MIX Scratch & Brown Preblended Stucco is available in 80 lb (36.2 kg) packages for easy hand loading or in 3,000 lb (1,360.7 kg) reusable bulk bags to be used with the various SPEC MIX silo systems. When using the silo system, once the bulk bags of stucco are delivered to the project site, the portable silo is loaded with a jobsite forklift and the product is dispensed into a mechanical batch mixer.

MIXING INSTRUCTIONS

WEAR IMPERVIOUS GLOVES, such as nitrile.

1. Add approximately 1.2 to 1.5 gallons (4.5 to

5.7 liters) of clean water into the mixer for each 80 lb (36.2 kg) bag.

2. Slowly pour the contents of the bag(s) into the mixer.

3. Mix for 5 minutes until a firm, workable consistency is achieved. Avoid over mixing as this may affect the integrity of the finished product.

4. If more water is needed, add small amounts at a time and continue to mix until the desired consistency is achieved. Do not exceed a total volume of 1.75 gallons (6.6 liters) of water for each 80 lb (36.2 kg) bag.

5. Keep mixing times and procedures the same every batch. Over mixing may entrain air, which can adversely affect plastic and hardened stucco properties. Prepare only as much mix as can be applied in one hour.

CURING: Stucco must be water cured with a fine mist once it has achieved final set. Care must be exercised when moist curing to avoid erosion damage to plaster surfaces. Spray the wall periodically for 48 hours. During hot and dry conditions, additional precautions may be necessary, including more frequent spraying or the erection of barriers to deflect sunlight and wind.

LIMITATIONS

SPEC MIX Scratch & Brown Preblended Stucco should be installed in accordance with the provisions of the local building code and applicable ASTM standards. Good workmanship coupled with proper detailing and design assures durable, functional, watertight construction. Follow proper cold-weather and hot-weather application procedures at temperatures below 40 ºF (4 ºC) or above 100 ºF (38 ºC) respectively.

LIMITED WARRANTY

IN THE UNITED STATES

NOTICE: Obtain the applicable LIMITED WARRANTY at www.specmix.com/product-warranty or send a written request to SPEC MIX, LLC, Five Concourse Parkway, Atlanta, GA 30328, USA.

AVISO: Obtenga la GARANTÍA LIMITADA correspondiente en www.specmix.com/product-warranty o envíe una solicitud por escrito a SPEC MIX, LLC, Five Concourse Parkway, Atlanta, GA 30328, USA.

IN CANADA

NOTICE: Obtain the applicable LIMITED WARRANTY at www.specmix.com/product-warranty or send a written request to SPEC MIX, LLC, Five Concourse Parkway, Atlanta, GA 30328, USA.

AVIS: Obtenez la GARANTIE LIMITÉE applicable sur www.specmix.com/produit-garantie. Ou envoyez une demande écrite à SPEC MIX, LLC, Five Concourse Parkway, Atlanta, GA 30328, USA.

SCRATCH & BROWN PREBLENDED STUCCO

Note: The yields given above are approximate and depend on labor practices, site conditions and design of work. Yields include typical waste. Please contact your local representative for more specific yield information in your area.

ESTIMATED YIELDS

Package Weight Thickness Coverage

80 lb (36.2 kg) 3/8 in (9.5 mm) 20 to 24 ft2 (1.8 to 2.2 m2)

80 lb (36.2 kg) 1/2 in (13 mm) 15 to 18 ft2 (1.4 to 1.7 m2)

80 lb (36.2 kg) 3/4 in (19 mm) 10 to 12 ft2 (0.9 to 1.1 m2)

3,000 lb (1,360.7 kg) 3/8 in (9.5 mm) 750 to 900 ft2 (70 to 84 m2)

3,000 lb (1,360.7 kg) 1/2 in (13 mm) 560 to 675 ft2 (52 to 63 m2)

3,000 lb (1,360.7 kg) 3/4 in (19 mm) 375 to 450 ft2 (35 to 42 m2)