042000_04_00 Termination Bar Submittal_EGI.pdf

F.H. PASCHEN, S.N. NIELSEN & ASSOCIATES LLC

1344 La France Street, NE Suite 2, Atlanta, GA 30307

p. 404.942.1307 f. 404.228.4050 | www.fhpaschen.com

SUBMITTAL COVER SHEET

Fill out items 1 through 4 below and submit product data sheet, sample, shop drawing, or other items submitted to the Owner/Architect/Engineer. Each submittal line item shall have its own Submittal Cover Sheet.

Project Name: KSU Clendenin Building Envelope Repairs Contractor: FH Paschen

Project Manager: Justice Hill

Address:

739 Trabert Ave NW Atlanta, GA 30318

Phone: 770-584-4267

Architect/Engineer: Olu Oshinubi – Epsten Group Owner: Kennesaw State University

Owner Project Manager:

Emmanuel Bertrand - KSU

1. Date: ______9/27/24 _____

2. Submitted Item: ________Aluminum Termination Bar

3. Manufacturer: ____Hohmann & Barnard Inc.___

4. Notes: _____

Contractor’s Stamp Owner/ Engineer/ Architect Stamp

No exception taken.

Revise as noted. Do not resubmit. See Notes above.

Revise as noted. Resubmit. See Notes above.

Rejected. See Notes above.

Checking of submittals is only for general conformance with the design concept of the Project and general compliance with the information given in Contract Documents. Any action shown is subject to the requirements of the Drawings and Specifications. Contractor is responsible for dimensions to be confirmed and correlated at the job site, quantities, information that pertains solely to the fabrication processes or to techniques of construction, coordination of the work of all trades, and the satisfactory performance of his work.

By: Date: 09/26/24Olu Oshinubi, VP / Arch

APPROVED

APPROVED AS CORRECTED

REVISE AND RESUBMIT

REJECTED

Fabrication / Installation may be undertaken. Approval does not authorize changes to the Contract Sum or Contract Time.

Fabrication and/or Installation MAY NOT be undertaken. In resubmitting, limit corrections to items marked.

NO PRIOR APPROVAL STAMP

BY CONTRACTOR

NOT A REQUIRED SUBMITTAL

ACTION AS NOTED BELOW

Review / approval neither extends nor alters contractual obligations of the Architect or Contractor.

The Epsten Group, Inc.

DATE REVIEWER

X

Olu Oshinubi, VP / Arch09/30/24

SIDE VIEW

DRAWINGS FOR ILLUSTRATIVE PURPOSES ONLY

T2 - Aluminum Termination Bar AA 6063-T6 Aluminum (GRADE TB-75) termination bar for use at top of flashing to mechanically secure it to the backup.

Compatible with all H&B Surface-Mount membrane and copper-laminate flashings.

NOTE: Available with optional Foam-Tite Seal™ to aid in inhibiting moisture infiltration. A factory-installed foam strip helps to seal small voids occurring between the termination bar and irregular substrate surfaces, while offering protection against water penetration due to sealant deterioration.

T2 - Aluminum Termination Bar

Product:

T2 Aluminum OPTIONAL: T2 Aluminum-FTS (Foam-Tite Seal™)

Dimensions:

• 14 ga. x 1” x 8’ long

• Has a 1/4” flange on top for easy caulking

• 1/4” holes spaced 8” o.c.

45°

3/4”

14 ga.

Flashing and Reglets

HOHMANN & BARNARD, Inc.

30 Rasons Court | Hauppauge, NY 11788

CORPORATE HEADQUARTERS

T: 800.645.0616 F: 631.234.0683 www.h-b.com

Branch/Subsidiary Locations:

ALABAMA - ARIZONA - ILLINOIS

MARYLAND - NEW YORK

PENNSYLVANIA - TEXAS - UTAH

CANADA

© 2013-2016 MiTek®

IMPORTANT: Since each construction project is unique, the appropriate selection and use of any product contained herein must be determined by competent architects, engineers and other appropriate professionals who are familiar with the specific requirements of the project in question.

This drawing and/or data sheet is the confidential and proprietary information of Hohmann & Barnard, Inc. and is not to be reproduced, copied or disclosed, in whole or in part, without the prior written consent of H&B.

NOTE: H&B recommends termination bars be fastened 8" o.c.

(Metal term bars can be fastened 16” o.c. for metal stud backup)