ATT_0019_HAND_HELD_METAL_DETECTOR_Draft_TM_5-6350-312-10_-_20_Sep_2010.pdf

TM 5-6350-312-10

TECHNICAL MANUAL

OPERATOR’S MANUAL

FOR

DETECTOR, METAL: HAND HELD

NSN 6350-01-553-1624

DISTRIBUTION STATEMENT A - Approved for public release; distribution unlimited.

HEADQUARTERS, DEPARTMENT OF THE ARMY

20 SEPTEMBER 2010

DRAFT

DRAFT

WARNING SUMMARY

a

To avoid electrical shock, do not use a damaged or tampered metal detector and do not immerse the metal detector in water.

Do not use the metal detector for more than 50 minutes per hour. The operator should allow 10 minutes to rest hand and wrist.

Do not touch the detection area (sensor) against bare skin. Contact may cause a skin rash and/or damage the detection area (sen-sor).

Use caution when handling the battery. Do not puncture or mutilate the battery. Do not handle a damaged battery. Do not inhale battery fumes.

Any leaking or damaged batteries must be discarded in accordance with local Standing Operating Procedure (SOP).

This Page Intentionally Left Blank b i

HEADQUARTERS,

DEPARTMENT OF THE ARMY

WASHINGTON, DC, 20 SEPTEMBER 2010

TECHNICAL MANUAL

OPERATOR’S MANUAL

FOR

DETECTOR, METAL: HAND HELD

NSN 6350-01-553-1624

DISTRIBUTION STATEMENT A - Approved for public release; distribution unlimited.

TABLE OF CONTENTS

WP Sequence No.

How to Use This Manual

Chapter 1 - General Information, Equipment Description, and Theory of Operation General Information Equipment Description and Data Theory of Operation

Chapter 2 - Operator Instructions Description and Use of Controls and Indicators Operation Under Usual Conditions Operation Under Unusual Conditions

Chapter 3 - Troubleshooting Procedures Troubleshooting Introduction Troubleshooting Procedures

Chapter 4 - Maintenance Instructions Preventive Maintenance Checks and Services (PMCS) Introduction Preventive Maintenance Checks and Services (PMCS) Replace Battery

Chapter 5 - Supporting Information References Components of End Item (COEI) and Basic Issue Items (BII) Lists Expendable and Durable Items List Hardware Support

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter or DA Form 2028 (Recommended Changes to Publications and Blank Forms), located in the back of this manual, directly to: Logistics Research and Engineering Directorate (RDAR-EIL-LS), U.S. Army RDECOM, Armament Research, Development and Engineering Center, Picatinny Arsenal, NJ 07806-5000. You may also send in your recommended changes via electronic mail or by fax. Our e-mail address is PICAPubChanges@conus.army.mil. Our fax number is DSN 880-4633, Commercial (973) 724-4633. A reply will be furnished to you.

ii

HOW TO USE THIS MANUAL

GENERAL

This manual contains all descriptive, operational, troubleshooting and maintenance information required to operate and main-tain the Detector, Metal: Hand Held.

CONTENT OF MANUAL

This manual is divided into 5 chapters:

Chapter 1, General Information, Equipment Description, and Theory of Operation Chapter 2, Operator Instructions Chapter 3, Troubleshooting Procedures Chapter 4, Maintenance Instructions Chapter 5, Supporting Information

HOW TO ACCESS INFORMATION

The easiest way to find information is by using the Table of Contents located at the front of the manual.

The chapters are divided into work packages (WP). Each WP is assigned a four digit sequence number. The sequence num-bers run consecutively throughout the manual. WPs added after initial publication follow a point numbering scheme to create a new sequence number that logically fits between the two existing WP numbers (e.g., 0005.1 is a WP added between WPs 0005 and 0006). WP page numbers are numbered consecutively and consist of the WP sequence number followed by -1, -2, -3, etc. (e.g., 0005-1, 0005-2, etc.). Each WP begins with page number -1.

CHAPTER 1

GENERAL INFORMATION, EQUIPMENT DESCRIPTION,

AND THEORY OF OPERATION

FOR

METAL DETECTOR

TM 5-6350-312-10 0001

0001-1

OPERATOR

GENERAL INFORMATION

SCOPE

This Technical Manual (TM) contains instructions for operating and maintaining the metal detector.

Type of Manual: Operator.

Model Number(s) and Equipment Name(s): Detector, Metal: Hand Held.

Purpose of Equipment: To detect metal (e.g., weapons, detonators, etc.) on personnel or in objects (e.g., containers, baggage, etc.).

MAINTENANCE FORMS, RECORDS, AND REPORTS

Department of the Army forms and procedures used for equipment maintenance will be those prescribed by (as applicable) DA PAM 750-8, The Army Maintenance Management System (TAMMS) Users Manual, or AR 700-138, Army Logistics Readiness and Sustainability.

REPORTING EQUIPMENT IMPROVEMENT RECOMMENDATIONS (EIR)

If your metal detector needs improvement, let us know. Send us an EIR. You, the user, are the only one who can tell us what you don’t like about your equipment. Let us know why you don’t like the design or performance. If you have Internet access, the easiest and fastest way to report problems or suggestions is to go to https://aeps.ria.army.mil/aepspublic.cfm (scroll down and choose the “Submit Quality Deficiency Report” bar). The Internet form lets you choose to submit an Equipment Improve-ment Recommendation (EIR), a Product Quality Deficiency Report (PQDR) or a Warranty Claim Action (WCA). You may also submit your information using an SF Form 368, Product Quality Deficiency Report. You can send your SF Form 368 via e-mail, regular mail, or facsimile using the addresses/facsimile numbers specified in DA PAM 750-8, The Army Maintenance Management System (TAMMS) Users Manual. We will send you a reply.

CORROSION PREVENTION AND CONTROL (CPC)

Corrosion Prevention and Control (CPC) of Army materiel is a continuing concern. It is important that any corrosion prob-lems with this item be reported so that the problem can be corrected and improvements can be made to prevent the problem in future items.

Corrosion specifically occurs with metals. It is an electrochemical process that causes the degradation of metals. It is com-monly caused by exposure to moisture, acids, bases, or salts. An example is the rusting of iron. Corrosion damage in metals can be seen, depending on the metal, as tarnishing, pitting, fogging, surface residue, and/or cracking.

Plastics, composites, and rubbers can also degrade. Degradation is caused by thermal (heat), oxidation (oxygen), solvation (solvents), or photolytic (light, typically UV) processes. The most common exposures are excessive heat or light. Damage from these processes will appear as cracking, softening, swelling, and/or breaking.

SF Form 368, Product Quality Deficiency Report, should be submitted to the address specified in DA PAM 750-8, The Army Maintenance Management System (TAMMS) Users Manual.

DESTRUCTION OF ARMY MATERIEL TO PREVENT ENEMY USE

Metal detector should be destroyed by any method so it can’t be used by unfriendly personnel.

TM 5-6350-312-10 0001

0001-2

WARRANTY INFORMATION

Refer to WP 0015 for warranty information.

NOMENCLATURE CROSS-REFERENCE LIST

LIST OF ABBREVIATIONS/ACRONYMS

SAFETY, CARE, AND HANDLING

ALL Warnings, Cautions and Notes must be observed throughout this manual. Their contents must be read and understood to prevent serious personnel injury and/or damage to equipment.

END OF WORK PACKAGE

Common Name Official Nomenclature

Metal Detector Detector, Metal: Hand Held

Abbreviation/Acronym Definition

BII Basic Issue Item

COEI Component of End Item

CPC Corrosion Prevention and Control ft Foot/Feet

in. Inch(es) lb Pound(s)

MAC Maintenance Allocation Chart

NSN National Stock Number

PMCS Preventive Maintenance Checks and Services

SOP Standing Operating Procedure

TM Technical Manual

WP Work Package

TM 5-6350-312-10 0002

0002-1

OPERATOR

EQUIPMENT DESCRIPTION AND DATA

EQUIPMENT CHARACTERISTICS, CAPABILITIES, AND FEATURES

The portable metal detector is designed to detect metal carried by people or objects. The shape of the scanner makes it easy to use for detecting weapons, detonators, or other pieces of metal on people or in parcels, baggage, correspondence, fabric, etc. It detects ferrous metals (containing iron), non-ferrous metals, and stainless steel. It uses a 9-volt alkaline battery with a maximum endurance of 60 hours of normal use.

LOCATION AND DESCRIPTION OF MAJOR COMPONENTS

EQUIPMENT DATA

END OF WORK PACKAGE

COMPONENT DESCRIPTION

Safety Sling Slips around wrist to prevent user from dropping metal detector.

Detection Area (Sensor) Main sensor that detects metal.

Speaker Provides audible sound when metal is detected.

Rubber Weatherproof Handle Allows user to firmly grip detector.

Battery Cover Secures battery in place.

Part number ......................................................... GMD1165185 Dimensions.......................................................... 16.5 x 3.25 x 1.62 in. (42 x 8.3 x 4.13 cm) Weight ............................................................... 17.6 oz (499 g) Temperature range............................................... -35º to 158º F (-37º to 70º C) Voltage ............................................................... 6.8 to 10 Vdc

(SENSOR)

0002-2

TM 5-6350-312-10 0002

TM 5-6350-312-10 0003

0003-1

OPERATOR

THEORY OF OPERATION

METAL DETECTOR

When the metal detector is turned on, a green light turns on indicating the detector is ready to be used. When the detection area (sensor) on the metal detector is waved within 2 inches around a person or an object, the metal detector makes a siren sound and a red light turns on. If the battery is down to 10%, an amber light turns on and the whistling sound changes to a steady tone.

END OF WORK PACKAGE

0003-2

TM 5-6350-312-10 0003

CHAPTER 2

OPERATOR INSTRUCTIONS

FOR

METAL DETECTOR

TM 5-6350-312-10 0004

0004-1

OPERATOR

DESCRIPTION AND USE OF CONTROLS AND INDICATORS

INTRODUCTION

The following table(s) and illustration(s) provide the description and use of controls and indicators pertaining to the metal detector.

METAL DETECTOR

Table 1. Metal Detector Controls and Indicators.

END OF WORK PACKAGE

Figure 1. Metal Detector Controls and Indicators.

KEY CONTROL OR INDICATOR FUNCTION

1 ON/OFF Button Turns detector on and off.

2 Ready Light (Green) Indicates detector is ready to be used.

3 Low Battery Light (Amber) Indicates battery is low.

4 Alert Light (Red) Indicates metal object is detected.

5 Interference Elimination Button Temporarily decreases sensitivity of detector to prevent interference from nearby metal objects.

1 2 3 4

0004-2

TM 5-6350-312-10 0004

TM 5-6350-312-10 0005

0005-1

OPERATOR

OPERATION UNDER USUAL CONDITIONS

INITIAL SETUP:

OPERATING PROCEDURES

WARNING

To avoid electrical shock, do not use a damaged or tampered metal detector and do not immerse the metal detec-tor in water.

Do not use the metal detector for more than 50 minutes per hour. The operator should allow 10 minutes to rest hand and wrist.

Do not touch the detection area (sensor) against bare skin. Contact may cause a skin rash and/or damage the detection area (sensor).

CAUTION

Do not attach metallic labels to the detection area (sensor) of the metal detector. The detector’s efficiency may become reduced.

1. Put hand through the safety sling and grip the handle.

2. Use the ON/OFF button to turn on the metal detector. There will be a short sound and the green ready light turns on. The green ready light remains on while the detector is turned on.

3. Wave the detector within 2 inches around the person or object being inspected. When metal is detected, the detector makes a siren sound and the red alert light turns on.

4. If necessary, press the interference elimination button on the underside of the detector to briefly eliminate detection of any nearby metal objects (e.g., metal walls).

NOTE

When the battery is down to 10%, the amber low battery light turns on and the detection (sensor) sound changes from a siren sound to a steady tone. There is approximately one hour of operational time remaining.

END OF TASK

END OF WORK PACKAGE

Not Applicable

DETECTION AREA

HANDLE

INTERFERENCE

ELIMINATION

BUTTON

RED ALERT

LIGHT

GREEN READY

LIGHT

ON/OFF

BUTTON

(SENSOR)

AMBER LOW

BATTERY LIGHT

SAFETY

SLING

0005-2

TM 5-6350-312-10 0005

TM 5-5340-101-10 0006

0006-1

OPERATOR

OPERATION UNDER UNUSUAL CONDITIONS

INITIAL SETUP:

UNUSUAL ENVIRONMENT/WEATHER

WARNING

To avoid electrical shock, do not immerse the metal detector in water.

The metal detector should not be used during wet weather.

END OF TASK

END OF WORK PACKAGE

Not Applicable

0006-2

TM 5-5340-101-10 0006

CHAPTER 3

TROUBLESHOOTING PROCEDURES

FOR

METAL DETECTOR

TM 5-6350-312-10 0007

0007-1

OPERATOR

TROUBLESHOOTING INTRODUCTION

TROUBLESHOOTING PROCEDURES

The troubleshooting work packages contain tables listing the malfunctions, tests or inspections, and corrective actions required to return the metal container to normal operation. Perform the steps in the order they appear in the tables.

Each work package is headed by an initial setup. This setup outlines what is needed as well as certain conditions which must be met before starting the task. DON’T START A TASK UNTIL:

You understand the task.

You understand what you are to do.

You understand what is needed to do the work.

You have the things you need.

This manual cannot list all malfunctions that may occur, or all tests or inspections and corrective actions. If a malfunction is not listed or is not corrected by listed corrective actions, notify your supervisor or Field maintenance.

0007-2

TM 5-6350-312-10 0007

TM 5-6350-312-10 0008

0008-1

OPERATOR

TROUBLESHOOTING PROCEDURES

INITIAL SETUP:

NOTE

If there are any hardware issues, the troubleshooting procedures in this manual should be performed to correct the problem. If the problem cannot be corrected, the Project Officer at Product Manager Improvised Explosive Device Defeat/Protect Force (PM IEDD/PF) must be contacted for hardware support. See WP 0015.

METAL DETECTOR

END OF WORK PACKAGE

References

WP 0011

WP 0015

Table 1. Troubleshooting Procedures for the Metal Detector.

MALFUNCTION TEST OR INSPECTION CORRECTIVE ACTION

METAL DETECTOR DOES NOT

OPERATE PROPERLY.

1. Slide ON/OFF button to the ON position. Look for green ready light to turn on.

If amber low battery light is lit, replace battery (see WP 0011).

2. Wave detector over metal object.

Listen for siren sound and look for red alert light to turn on.

3. Check battery polarity. If necessary, re-install battery correctly (see WP 0011).

0008-2

TM 5-6350-312-10 0008

CHAPTER 4

MAINTENANCE INSTRUCTIONS

FOR

METAL DETECTOR

TM 5-6350-312-10 0009

0009-1

OPERATOR

PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) INTRODUCTION

INITIAL SETUP:

GENERAL

The PMCS provides procedures to ensure that the metal detector components are in operating condition.

EXPLANATION OF COLUMNS IN THE PMCS TABLE

1. Item Number Column - Numbers in this column are for reference. Item numbers appear in the order in which checks and services must be performed for the intervals listed.

2. Interval Column - This column tells you when each check is to be performed in the procedure column.

3. Man-hour Column - This column gives the man-hours required to complete all prescribed lubrication services.

4. Item To Be Checked or Serviced Column - This column lists the item to be checked or serviced.

5. Procedure Column - This column gives the procedure you must do to check or service the item listed in the Item To Be Checked or Serviced column to know if the equipment is ready or available for its intended mission or for operation. You must do the procedure at the time stated in the interval column.

6. Equipment Not Ready/Available If: Column - Information in this column tells you what faults will keep your equipment from being capable of performing its primary mission. If applicable, following Equipment Not Ready/Available If: condi-tion is a suggested remedy that will correct the discovered discrepancy. Follow standard operating procedures for main-taining the equipment or reporting equipment failure. Report any malfunctions or failures on DA Form 2404 (Equipment Inspection and Maintenance Worksheet) or refer to DA PAM 750-8, The Army Maintenance Management System (TAMMS) Users Manual.

END OF WORK PACKAGE

References DA Form 2404

DA PAM 750-8

0009-2

TM 5-6350-312-10 0009

TM 5-6350-312-10 0010

0010-1

OPERATOR

PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)

INITIAL SETUP:

PMCS FOR METAL DETECTOR

END OF WORK PACKAGE

Materials/Parts Rag, wiping (item 2, WP 0014)

References

WP 0011

Table 1. PMCS for Metal Detector.

ITEM

NO. INTERVAL

MAN-

HOUR

ITEM TO BE

CHECKED OR

SERVICED PROCEDURE

EQUIPMENT

NOT READY/

AVAILABLE IF:

1 Before Metal Detector WARNING To avoid electrical shock, do not use a damaged or tampered metal detector and do not immerse the metal detector in water.

1. Inspect detector for dirt or debris.

Use damp rag to clean if needed.

Detector is too dirty to operate properly.

2. Inspect detector for broken or miss-ing parts.

Detector has broken or missing parts.

3. Turn on detector to check battery power. Replace battery if necessary (see WP 0011).

Green ready light does not turn on.

4. Ensure detector operates correctly by waving detection area (sensor) within 2 inches of various metals.

Detector does not make siren sound or red alert light does not turn on.

2 After Battery CAUTION Remove battery if detector will be stored for more than 30 days or damage to detector may occur.

If storing detector, remove battery.

0010-2

TM 5-6350-312-10 0010

TM 5-6350-312-10 0011

0011-1

OPERATOR

REPLACE BATTERY

INITIAL SETUP:

REPLACING BATTERY

WARNING

Use caution when handling the battery. Do not puncture or mutilate the battery. Do not handle a damaged bat-tery. Do not inhale battery fumes.

Any leaking or damaged batteries must be discarded in accordance with local SOP.

1. Ensure the metal detector is turned off.

CAUTION

The battery cover is designed to slide off the handle. To avoid damage to the battery cover or handle, do not try to yank off the battery cover.

2. Slide the battery cover off the bottom of the handle.

3. If necessary, remove the old 9-volt battery.

NOTE

The battery cover will not be able to be re-attached if the battery is incorrectly installed.

4. Install a new 9-volt battery, ensuring correct polarity.

5. Slide the battery cover onto the handle until it clicks it place.

END OF TASK

END OF WORK PACKAGE

Materials/Parts Battery, 9-volt (item 1, WP 0014)

BATTERY COVER

HANDLE

9-VOLT BATTERY

0011-2

TM 5-6350-312-10 0011

CHAPTER 5

SUPPORTING INFORMATION

FOR

METAL DETECTOR

TM 5-6350-312-10 0012

0012-1

OPERATOR

REFERENCES

SCOPE

This work package lists all Army regulations, forms, pamphlets, and miscellaneous publications referenced in this manual.

END OF WORK PACKAGE

ARMY REGULATIONS

AR 75-1 Malfunctions Involving Ammunition and Explosives

AR 385-10 The Army Safety Program

AR 700-138 Army Logistics Readiness and Sustainability

FORMS

DA Form 285 Technical Report of U.S. Army Ground Accident

DA Form 2028 Recommended Changes to Publications and Blank Forms

DA Form 2404 Equipment Inspection and Maintenance Worksheet

SF Form 368 Product Quality Deficiency Report

PAMPHLETS

DA PAM 750-8 The Army Maintenance Management System (TAMMS) Users Manual

MISCELLANEOUS PUBLICATIONS

CTA 8-100 Army Medical Department Expendable/Durable Items

CTA 50-909 Field and Garrison Furnishings and Equipment

CTA 50-970 Expendable/Durable Items (Except Medical, Class V, Repair Parts, and Heraldic Items)DRAFT

0012-2

TM 5-6350-312-10 0012

TM 5-6350-312-10 0013

0013-1

OPERATOR

COMPONENTS OF END ITEM (COEI) AND BASIC ISSUE ITEMS (BII) LISTS

INTRODUCTION

Scope

This work package lists COEI and BII for the metal detector to help you inventory items for safe and efficient operation of the equipment.

General

The COEI and BII information is divided into the following lists:

Components of End Item (COEI). This list is for information purposes only and is not authority to requisition replacements.

These items are part of the metal detector. As part of the end item, these items must be with the end item whenever it is issued or transferred between property accounts. Items of COEI are removed and separately packaged for transportation or shipment only when necessary. Illustrations are furnished to help you find and identify the items.

Basic Issue Items (BII). These essential items are required to place the metal detector in operation, operate it, and to do emer-gency repairs. Although shipped separately packaged, BII must be with the metal detector during operation and when it is transferred between property accounts. Listing these items is your authority to request/requisition them for replacement based on authorization of the end item by the TOE/MTOE. Illustrations are furnished to help you find and identify the items.

Explanation of Columns in the COEI List and BII List

Column (1) Illus Number. Gives you the number of the item illustrated.

Column (2) National Stock Number (NSN). Identifies the stock number of the item to be used for requisitioning purposes.

Column (3) Description, Part Number/(CAGEC). Identifies the Federal item name (in all capital letters) followed by a mini-mum description when needed. The stowage location of COEI and BII is also included in this column. The last line below the description is the part number and the Commercial and Government Entity Code (CAGEC) (in parentheses).

Column (4) Usable On Code. When applicable, gives you a code if the item you need is not the same for different models of equipment.

Column (5) U/I. Unit of Issue (U/I) indicates the physical measurement or count of the item as issued per the National Stock Number shown in column (2).

Column (6) Qty Rqr. Indicates the quantity required.

TM 5-6350-312-10 0013

0013-2

BASIC ISSUE ITEMS (BII) LIST

Table 1. Components of End Item List.

(1) (2) (3) (4) (5) (6)

ILLUS

NUMBER

NATIONAL STOCK

NUMBER (NSN) DESCRIPTION, PART NUMBER/(CAGEC)

USABLE

ON

CODE U/I

QTY

RQR

1 6350-01-553-1624 DETECTOR, METAL: HAND HELD EA 1

Table 2. Basic Issue Items List.

(1) (2) (3) (4) (5) (6)

ILLUS

NUMBER

NATIONAL STOCK

NUMBER (NSN) DESCRIPTION, PART NUMBER/(CAGEC)

USABLE

ON

CODE U/I

QTY

RQR

N/A TM 5-6350-312-10, Operator’s Manual EA 1

COMPONENTS OF END ITEM (COEI) LIST

TM 5-6350-312-10 0014

0014-1

OPERATOR

EXPENDABLE AND DURABLE ITEMS LIST

INTRODUCTION

Scope

This work package lists expendable and durable items that you will need to operate and maintain the metal detector. This list is for information only and is not authority to requisition the listed items. These items are authorized to you by CTA 50-970, Expendable/Durable Items (Except Medical, Class V, Repair Parts, and Heraldic Items), CTA 50-909, Field and Garrison Fur-nishings and Equipment, or CTA 8-100, Army Medical Department Expendable/Durable Items.

Explanation of Columns in the Expendable/Durable Items List

Column (1) Item No. This number is assigned to the entry in the list and is referenced in the narrative instructions to identify the item (e.g., Use brake fluid (WP 0098, Item 5).).

Column (2) Level. This column identifies the lowest level of maintenance that requires the listed item (C = Crew).

Column (3) National Stock Number (NSN). This is the NSN assigned to the item which you can use to requisition it.

Column (4) Item Name, Description, Part Number/(CAGEC). This column provides the other information you need to iden-tify the item. The last line below the description is the part number and the Commercial and Government Entity Code (CAGEC) (in parentheses).

Column (5) U/I. Unit of Issue (U/I) code shows the physical measurement or count of an item, such as gallon, dozen, gross, etc.

EXPENDABLE AND DURABLE ITEMS LIST

END OF WORK PACKAGE

Table 1. Expendable and Durable Items List.

(1) (2) (3) (4) (5)

ITEM

NO. LEVEL

NATIONAL STOCK

NUMBER (NSN) ITEM NAME, DESCRIPTION, PART NUMBER/(CAGEC) U/I

1 C 6135-00-900-2139 Battery, Nonrechargeable: 9-volt

ANSI C18.1M (80204

PG

2 C 7920-00-205-1711 Rag, Wiping: Unbleached, mixed colors (80244) 7920-00-205-1711

BE

0014-2

TM 5-6350-312-10 0014

TM 5-6350-312-10 0015

0015-1

OPERATOR

HARDWARE SUPPORT

INITIAL SETUP:

GENERAL

If there is a hardware issue(s) that cannot be corrected by performing the troubleshooting procedures, contact the Project Offi-cer (PO) and Logistics Managers (LMs) at Product Manager Improvised Explosive Device Defeat/Protect Force (PM IEDD/ PF) for support. Details of the hardware issue(s) need to be provided. The PO and LMs will coordinate the solution to the hardware issue(s).

PM IEDD/PF Project Officer and Logistics Managers’ contact information:

NOTE

Contact all three of the following personnel to ensure the hardware issue(s) is quickly acknowledged.

PO: Frank Altamura Email: frank.altamura@us.army.mil

LM: Jamie Kiessling Email: jamie.kiessling@conus.army.mil

LM: Joan Welch Email: joan.welch@us.army.mil

NOTE

The PO and LMs should be contacted with hardware issues only. If there are errors in the Technical Manual (TM), a DA Form 2028, located at the back of this manual, should be submitted.

END OF WORK PACKAGE

Not Applicable

0015-2

TM 5-6350-312-10 0015

TM 9-1375-225-13 18 Jun 99 SOF Demo Kit, M303

Page 0012-5. Add callout “2” to the shaft slinger

Reason: Callout missing from illustration.

Page 0001-2. Change “Rock Island, IL 61201” to read “Aberdeen Proving Ground, MD 21010”.

Reason: Wrong Address.

SAM

PLE

2 5 .in the illustration.

LRED (RDAR-EIL-LS)

Picatinny Arsenal, NJ 07806-5000 U.S. Army RDECOM, ARDEC

20 Sep 10Draft TM 5-6350-312-10 Detector, Metal: Hand Held

U.S. Army RDECOM, ARDEC

U.S. Army RDECOM, ARDEC

U.S. Army RDECOM, ARDEC