JA ML-26-57 P171 Interior Finishes Brand Name or Equal - Redacted.pdf

DEPARTMENT OF THE NAVY

NAVAL FACILITIES ENGINEERING SYSTEMS COMMAND, MID-ATLANTIC

9324 VIRGINIA AVENUE

NORFOLK VIRGINIA 23511-3095

J&A No. ML-26-57

CON/476

JUSTIFICATION AND APPROVAL

FOR USE OF OTHER THAN FULL AND OPEN COMPETITION

1. Contracting Activity.

The contracting activity is Naval Facilities Engineering Systems Command, Mid-Atlantic (NAVFAC ML), Norfolk, Virginia.

2. Description of the Action Being Approved.

This Justification and Approval (J&A) authorizes the use of �brand name or equal� references in construction solicitations where it is necessary to effectively communicate interior color and finish selection. Specific brand name finish and descriptions are listed in Attachment 1 below and are specific to solicitation N4008526R0020 and the resulting contract.

3. Description of Supplies/Services.

The intent of solicitation N4008526R0020, Design-Bid-Build (DBB) P171 Weapons Magazines, Naval Weapons Station Yorktown, Yorktown, Virginia is to construct five (5) Containerized Long Weapons Storage Two Bay (CLWS 2B) High Explosive magazines, two segregation facilities, and one forklift charging station to support Naval Munitions Command Atlantic. Magazine construction will consist of reinforced concrete mat foundations, walls, floors, entrance and loading aprons. Segregation facilities will be constructed of pile foundations, reinforced concrete walls, floors, roof, entrance and loading aprons. Facility-related control systems include cybersecurity features.

This acquisition will solicit proposals utilizing full and open competition, as authorized by the approved DD2579 on 13 January 2026. The estimated value of the work included in this construction solicitation is approximately and the estimated value of the brand name or equal materials subject to this J&A is . The project will be funded by FY24, FY26, and FY27 Military Construction, Navy (MCON) funds for construction. The work under this contract is required to be completed within 1287 calendar days after contract award.

In order to sufficiently define the scope of work to be performed by a general construction contractor, a Basis of Design (BOD) is prepared to document the principles, assumptions, rationale, criteria, and considerations used for calculations and decisions required during design. When preparing a BOD for a construction project, it is not practicable to convey the required finishes to potential offerors using generic descriptions. For example, it is not feasible to adequately describe a particular shade of paint color which must be used to provide a cohesive appearance for an aesthetically pleasing, professional environment;

however, the intended hue can be conveyed by referencing a particular manufacturer�s proprietary product, and that color can then be replicated in any brand of paint. Therefore, the use of brand name references is necessary to convey requirements to achieve the overall coordinated desired appearance but is not intended to restrict competition. The identified brand name items are intended to solely relay the BOD for the structural interior finishes. The specification for finish materials will include the manufacturer�s name, product line, model number, and any identifiable information specific to that material/finish accompanied by salient characteristics and generic technical specifications necessary for �equal� products to meet contract performance requirements. While it is possible for many manufacturers to produce finishes that are functionally equivalent to these designated finishes, the intent of providing a BOD is to have standard stock products to be provided without having custom products manufactured specifically for this facility. During the design of the facility, the designer of record has verified the products using manufacturer brand names are not proprietary, and can be met by many established manufacturers.

4. Statutory Authority Permitting Other Than Full and Open Competition.

Per DFARS 211.104, a justification and approval is required in order to use brand name or equal descriptions. The statutory authority for this acquisition permitting other than full and open competition is 10 U.S.C. 3204(a)(1) which permits the use of limited suppliers when it is essential to the Government�s requirements, as implemented by Federal Acquisition Regulation (FAR) 6.103-1 (DEVIATION 2026-O0017), Only one responsible source and no other supplies or services will satisfy agency requirements.

This justification applies only to the brand name or equal products describing structural interior finishes, as specified in the construction contract documents for project Design-Bid-Build (DBB) P171 Weapons Magazines, Naval Weapons Station Yorktown, Yorktown, Virginia.

5. Rationale Justifying Use of Cited Statutory Authority.

The Structural Interior Design (SID) of a facility includes building-related design elements and components as part of the building construction to include but not limited to, paint, wall coverings, ceiling finishes, floor coverings (e.g. tile, carpet, etc.), primary window treatments (e.g. blinds, shades and drapery hardware, etc.), signage and built-in casework. The interior designer must determine the desired interior finish materials based on the required aesthetic, durability and maintenance qualities and characteristics applicable to each space within the facility. The SID is designed by a professional certified interior designer in accordance with Unified Facilities Criteria (UFC) 3-120-10 Interior Design, Chapter 2 paragraph �Interior Designer Qualifications.�

It is necessary for the government to include brand names or proprietary specifications for finishes to have a complete design that can be properly conveyed to the construction contractor for bidding. UFC Requirements: (reference UFC 3-120-10 with Change 1, paragraph 4-5.1).

The interior designer must provide all finish and color selections including finish code, manufacturer�s materials, textures, patterns, color names and numbers for all interior finishes and specialties which will be exposed to view in the finished construction.

In addition, the UFC stipulates the use of the following disclaimer: (reference UFC 3-120-10 with Change 1, paragraph 4-5.1.2):

The Government prohibits the use of proprietary materials, finishes and colors. A disclaimer must be used on the drawings or in the specifications indicating materials and colors are shown for reference only. However, it is important to use specific manufacturer, finish and color information to establish a frame of reference in the development of the [Structural Interior Design] SID. Reference UFGS 09 06 00 Schedules for Finishes for the appropriate disclaimer to use that addresses this issue when developing the

SID.

UFGS 09 06 00 Schedule for Finishes, Paragraph 2.1 states:

�The color schedule information provided in the following paragraphs lists the colors, patterns and textures required for exterior and interior finishes, including both factory applied and field applied colors. Where color is shown as being specific to one manufacturer, an equivalent color by another manufacturer may be submitted for approval. Manufacturers and materials specified are not intended to limit the selection of equal colors from other manufacturers.�

For construction contracts, FAR 52.236-5, Materials and Workmanship, addresses any potential competition concerns associated with including a basis of design on the plans or in the specifications and has been well defined and an industry standard by the construction contracting community for decades. In part, this clause states: �References in the specifications to equipment, material, articles, or patented processes by trade name, make, or catalog number, shall be regarded as establishing a standard of quality and shall not be construed as limiting competition. The Contractor may, at its option, use any equipment, material, article, or process that, in the judgment of the Contracting Officer, is equal to that named in the specifications, unless otherwise specifically provided in this contract.�

The identified brand/manufacturer items or proprietary specifications are intended to be examples for the basis of the facility�s interior design to help ensure visual integrity of the building�s interior finishes.

Interior finishes will be procured and installed as part of firm-fixed-price, design-bid-build construction contracts and will be solicited in accordance with all applicable policies, procedures, guidance, and laws related to competition. Paint colors and interior finishes of a building can easily be color-matched by a variety of manufacturers and suppliers. It is common in the industry for colors and finishes to be identified by a particular brand or manufacturer and that brand�s name or identifier for the product. The government has a legitimate need in this case for specific interior paint colors and building finishes, but does not seek to limit the source of those materials to a specific brand or manufacturer.

There is no alternative method to complete the Structural Interior Design (SID) for a design-bid-build contract and ensure an aesthetically, coordinated building interior. Utilizing a basis of design is a critical component of designing complete and coordinated structural interior design under the current UFC. It is not possible to fully design a coordinated system of interior materials and colors to meet technical requirements without assumptions of specific materials using manufacturer names and product information. The only potential alternative is to convert all solicitations into a design-build procurement without complete designs and require the effort of a professional, certified interior designer to meet the requirements set forth in UFC 3-120-10 Interior Design, after award to a Contractor. This alternative does not meet the government�s interests in providing a complete design for the facility since the government has determined a design-bid-build procurement for this facility is in the best interests of the government pursuant to FAR Part 36 (DEVIATION 2026-O0019) �Construction and Architect-Engineer Contracts� and Engineer Regulations (ER)1180-1-9.

6. Description of Efforts Made to Solicit Offers from as Many Offerors as Practicable.

The government is not attempting to limit competition or the supply of these materials to one source. No efforts were made to identify multiple sources of paint or interior finishes because the solicitation will not limit the ultimate contractor to providing materials from only one or a limited number of brands or manufacturers. The Notice of Intent for the brand name or equal items was published to SAM.gov on 31 March 2026 with a closing date of 15 April 2026. The intent for interior finishes yielded no responses. A pre-solicitation notice and solicitation will both be publicized on SAM.gov, in accordance with the requirements of FAR Part 5 (DEVIATION 2026-O0003). The approved J&A will also be made publicly available as required by FAR 6.301 (DEVIATION 2026-O0017).

7. Determination of Fair and Reasonable Cost.

The Contracting Officer will determine that the price for this acquisition is fair and reasonable in accordance with FAR Part 15 (DEVIATION 2026-O0017) prior to contract award. Analysis will be performed by one or more of the following techniques: (1) Comparison of proposed prices received in response to the RFP; (2) Comparison of proposed prices with the Independent Government Cost Estimate (IGCE); (3) Comparison of proposed prices with available historical information; and/or (4) Comparison of market survey results. The fair and reasonable determination will be made based on the total price of the project. These brand name or equal items are not individual line item prices in the solicitation.

8. Actions to Remove Barriers to Future Competition.

This solicitation does not limit competition. If it comes to NAVFAC MIDLANT�s attention that the proposed language is having a limiting effect on competition or the selection of alternate sources of material within the scope of this justification, the contracting officer will seek counsel and make efforts to take remedial measures.

CERTIFICATIONS AND APPROVAL