Attachment 16 - W3 LF 450PLUS Programming.pdf

PDF 89 KB Posted

Attached to
Veeder Root TLS 450 PLUS Upgrade Minot AFB, ND Federal contract opportunity
Solicitation number
FA4528-25-Q-SP02
Issued by
Department of the Air Force Global Strike Command

About this file

Written by GovTribe AI ·

This document contains detailed programming instructions for the W3 LF 450PLUS system, providing a comprehensive step-by-step guide for system setup and configuration. The instructions cover multiple configuration stages, including system setup, device configuration, tank settings, and security parameters. Key configuration steps include setting system language to English, configuring time and date settings, setting up tank parameters for a diesel tank (TK-101) with a 3,782-gallon capacity, configuring probes and sensors, setting relay configurations, and establishing user administration with specific security settings. The document provides granular instructions for each step, including enabling/disabling various system features, setting up tank profiles, configuring alarm and test settings, and establishing user access with specific security restrictions like disabling web access, SSH, and serial command ports.

View the file

Other files for this federal contract opportunity

Other files attached to Veeder Root TLS 450 PLUS Upgrade Minot AFB, ND, newest first.
File Type Posted
Amendment 6 18 Aug 25 Q A Veeder Root TLS 450 PLUS upgrade.pdf PDF
Amendment 5 13 Aug 25 Q A Veeder Root TLS 450 PLUS upgrade.pdf PDF
13 Aug 25 Q A Veeder Root TLS 450 PLUS upgrade.pdf PDF
Attachment 2 - Amendment 4 Statement of Work Veeder Root - 13 Aug 25.pdf PDF
Attachment 15 - W3 MAF 450 PLUS Programming.pdf PDF
Attachment 1 - Veeder Root TLS 450PLUSUpgrade Minot AFB Combo.pdf PDF
Attachment 1 - AMENDMENT Veeder Root TLS 450 PLUS Upgrade Minot AFB Combo.pdf PDF
Attachment 1 - Veeder Root TLS 450 PLUS Upgrade Minot AFB Combo.pdf PDF
Attachment 12 - LF Wire Routing with GMR 5 Alarm.pdf PDF
Attachment 7 - Junction and Conduit for Power and Relay Bay.pdf PDF
Attachment 5 - Financial Questionnaire Sheet.pdf PDF
Attachment 20 - WD 2015-6025 and WD 2015-5383.pdf PDF
Attachment 13 - LF Electrical Schematic with GMR 3 Alarm.pdf PDF
Attachment 6 - Past Performance Questionnaire.docx DOCX document
Attachment 4 - Limited Sources Justification - Veeder Root_Redacted.pdf PDF
Attachment 1 - Veeder Root TLS 450 PLUS Upgrade Minot AFB Combo.pdf PDF
Attachment 17 - Typical LF Site Layout 3 Configurations Typical MAF Site Layout Exterior.pdf PDF
Attachment 19 - Mileage to MAFS.xlsx XLSX spreadsheet
Attachment 18 -Site Security.docx DOCX document
Attachment 14 - LF Electrical Schematic with GMR 5 Alarm.pdf PDF
Attachment 10 - TLS-450 Plus Component Locations.pdf PDF
Attachment 9 - LF EMC Enclosure Layout.pdf PDF
Attachment 8 - Relay 3 for GMR 3 Wiring.pdf PDF
Attachment 2 - Statement of Work Veeder Root.pdf PDF
Attachment 16 - W3 LF TLS 450 PLUS Programming Instructions.pdf PDF
Attachment 15 - W3 MAF TLS 450 PLUS Programming Instructions.pdf PDF
Attachment 11 - LF Wire Routing with GMR 3 Alarm.pdf PDF
Attachment 3 - Quote Sheet Veeder Root TLS 450PLUS.xlsx XLSX spreadsheet
Show all 28

On GovTribe

Work with this file on GovTribe

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file
Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

W3 LF 450PLUS Programming Instructions

************************************************System Setup************************************************

1. Once the console has been installed and connected to the power panel boot the console and wait for the home screen to display.

2. Access Workflow Wizard Setup by touching MENU>SETUP> WORKFLOW WIZARD>SETUP

WORKFLOW

3. On the SETUP>DISPLAY>LANGUAGE/UNITS page, set System Language to English

4. Set System Units to US

5. Press checkmark to save any changes and press Next

6. Set Current Date

7. Set Current Time

8. Set Time Zone to (UTC -07:00) US/Mountain

9. Set NPT to DISABLED

10. Press checkmark to save any changes and press Next

11. Set Date Format to mm_dd_yyyy

12. Set Date Separator to /

13. Set Time Format to hh:mm AP

14. Press checkmark to save any changes and press Next

15. Set Decimal Separator to .

16. Set Thousands Separator to None.

17. Press checkmark to save any changes and press Next

18. Header 1: Enter site name (e.g. Alpha – 01)

19. Set Header 2: to street address

20. Set Header 3: to City, State, and ZIP code

21. Set Header 4: to Facility ID from state (e.g. XX-XXXX)

22. Press checkmark to save any changes and press Next

23. Set Alarm Filtering to Disabled

24. Press checkmark to save any changes and press Next

25. Enter System Hostname to TLS450

26. Press checkmark to save any changes and press Next

27. Set IP Default Gateway to Disabled

28. Press checkmark to save any changes and press Next

29. On Internal Modem menu, Press Next

30. On CDIM port menu, Press Next

31. Set TDIM Port configuration to Disabled.

32. Press checkmark to save any changes and press Next

33. Set TLG IFSF to disabled

34. Press checkmark to save any changes and press Next

35. Set Serial Port Configured to DISABLED

36. Press checkmark to save any changes and press Next

37. Ensure Email Relay Enabled is not checked

38. Press checkmark to save any changes and press Next

39. Set Gateway configuration to DISABLED

40. Press checkmark to save any changes and press Next

****************************************************Probe****************************************************

41. Set Up Devices Starting with Probe 1

42. Set Configuration to Enabled

43. Assign Address as B1.S1.x (x corresponds to the slot the Magnetostrictive probe was installed in)

44. Set Label to TK-101

45. Set FLOAT TYPE [IN] to corresponding float kit installed on Magnetostrictive probe (e.g. 2)

46. Set Water Minimum to [IN] to 0

47. Press Checkmark to save any changes

*************************************************Sump Sensor*************************************************

48. Select bottom left Probe icon to open the devices submenu

49. Select Liquid Sensor and begin configuring Liquid Sensor 1

50. Set configuration to enabled

51. Set address to B1.S1.x (x corresponds to the slot the Magnetostrictive probe was installed in)

52. Set label to Sump

53. Set Model to Tri-State (Single Float)

54. Set Category to Piping Sump

55. Press checkmark to save any changes

**********************************************Interstitial Sensor**********************************************

56. Select bottom left MAG Sensor icon to open devices submenu

57. Select Liquid Sensor and begin configuring Liquid Sensor 2

58. Set Configuration to enabled

59. Set address to B1.S1. x (x corresponds to the slot the Magnetostrictive probe was installed in)

60. Set label to Interstitial

61. Set Model to Tri-State (Single Float)

62. Set Category to Annular Space

63. Press checkmark to save any changes and press Next

****************************************************Relays****************************************************

64. Press the bottom left Liquid Sensor icon to open the devices submenu

65. Select Relay

66. Set configuration of Relay 1 to ENABLED

67. Set Address to B1.S7.1 (The relay address B1:S7:1 refers to the single input Power Bay relay)

68. Set Label to Overfill Alarm

69. Set type to Standard

70. Set Orientation to Normally Open

71. Press checkmark to save any changes

72. Select Relay 2 from bottom menu

73. Set configuration of Relay 2 to ENABLED

74. Set Address to B1.S2.5

75. Set Label to Alarm Output

76. Set type to Standard

77. Set Orientation to Normally Closed

78. Press checkmark to save any changes

79. Select Relay 3 from bottom menu

80. Set configuration of Relay 3 to ENABLED

81. Set Address to B1.S2.6

82. Set Label to Closed Loop

83. Set type to Standard

84. Set Orientation to Normally Open

85. Press checkmark to save any changes and press Next

****************************************************Tank 1****************************************************

86. Set up Tank 1

87. Set Tank 1 Configuration to enabled

88. Set tank label to TK – 101

89. Set product code to 1

90. Set Probe to Probe 1

91. Set Probe offset to 0.00 Inches

92. Set Full volume to 3782 GALLONS

93. Set Diameter to 72.0 Inches

94. Set tank tilt to 0.00 inches

95. Set Thermal Coefficient to 0.000450

96. Set Meter Data Present to DISABLED

97. Set Delivery Delay [min] to 1

98. Set Gross Test Fail to ENABLED

99. Set Periodic Test Fail to ENABLED

100. Set Annual test Fail to DISABLED

101. Set GOST Volume Correction to DISABLED

102. Press checkmark to save any changes and press Next

103. Setup Tank Limits for Tank 1

104. Set Max Volume (Label Vol.) [gal] to 3782

105. Set High Product (% of max. vol.) to 95%

106. Set Delivery Overfill to (% of max. vol.) 90%

107. Set Delivery Limit (% of Full vol.) to 10%

108. Set Low Product [gal] to 2600

109. Set High Water Warning [in.] to 1.0

110. Set High Water Alarm [in.] to 2.0

111. Set Water Alarm Filter Level to OFF

112. Set Water Alarm Filter Delay to 30 S

113. Set Leak Alarm Limit [gal] to 99

114. Set Sudden Loss Limit [gal] to 100

115. Set Fuel Temperature Low Limit [DEG F] to -58.0

116. Set Fuel Temperature High Limit to [DEG F] 140.0

117. Press checkmark to save any changes and press Next

118. Set Test Tank Method to CSLD

119. Set Probability of Detection to 95%.

120. Set Climate Factor to MODERATE

121. Set CSLD evaporation compensation to DIABLED

122. Set Stage II Vapor Recover to DISABLED

123. Press checkmark to save any changes and press Next

124. Set up Tank Profile for Tank 1

125. Set Tank Profile to FOUR POINTS

126. Set 54.0 INCHES [gal] to 3184

127. Set 36.0 INCHES [gal] to 2001

128. Set 18.0 INCHES [gal] to 781

129. Press checkmark to save any changes and press Next

130. Set up Tank charts

131. Press the check box next to entry 1

132. Press the actions menu

133. Select Apply chart check mark and press Next

**************************************************All Tanks***************************************************

134. On Siphon Sets page, press Next

135. Set up All Tanks

136. Set Ullage Display mode to USER ULLAGE

137. Set User Ullage % to 90

138. Set Print TC Volumes to DISABLED

139. Set Periodic Test Needed Warnings to DISABLED

140. Set Annual Test Needed Warnings to DISABLED

141. Set TC Density to DISABLED

142. Set Stick Height to DISABLED

143. Set Leak Test Report Format to STANDARD

144. Set Leak Test Region to EPA

145. Press checkmark to save any changes and press Next

**********************************************Product Mapping**********************************************

146. Check Product # 1 box

147. Press actions

148. Press edit label

149. Set product 1 label to DIESEL

150. Press checkmark to save any changes and press Next

151. Check tank # 1 box

152. Press actions

153. Press edit Tank(s) product mapping

154. Select Product 1 DIESEL

**************************************All else, Tasks, Custom Alarms**************************************

155. Press checkmark to save any changes and press Next

156. Set Pumps and Lines > Pumps, Configured to disabled

157. Press checkmark to save any changes and press Next

158. Set Pumps and Lines > Line, Configured to disabled

159. Press checkmark to save any changes and press Next

160. On PLLD, Press Next

161. Set Pumps and Lines > All Lines, Restart on Alarm Clear to DISABLED

162. Set Line Lockout Schedule to disabled

163. Press checkmark to save any changes and press Next

164. Set Pumps and Lines > All PLLD, set Line Re-Enable method to Pass Line Test

165. Set Periodic Test Warnings to DISABLED

166. Set Annual Test Warnings to DISABLED

167. Press checkmark to save any changes and press Next

168. On Inventory > Report Times, Set Reporting Interval to DISABLED

169. Press checkmark to save any changes and press Next

170. Set shift close method to TIMED

171. Press checkmark to save any changes and press Next

172. Set delivery method to Standard Automatic

173. Set Tank Idle Delivery to DISABLED

174. Press checkmark to save any changes and press Next

175. On Address Book menu select next

176. On Automatic Events > AutoXmit, set delay time (Secs) to 5

177. Set repeat time (mins) to 60

178. Set Leak Alarm to DISABLED

179. Set High Water Alarm to DISABLED

180. Set Overfill Alarm to DISABLED

181. Set Low Limit Alarm to DISABLED

182. Set Theft Alarm to DISABLED

183. Set Delivery Start to DISABLED

184. Set Delivery Stop to DISABLED

185. Set External Input On to DISABLED

186. Set External Input Off to DISABLED

187. Set Sensor Fuel Alarm to DISABLED

188. Set Sensor Water Alarm to DISABLED

189. Set Sensor Out Alarm to DISABLED

190. Press checkmark to save any changes and press Next

191. On Autoconnect Tasks menu select next

192. On Device tasks menu select Actions

193. Press Add Task

194. Set Device as RELAY 1: Overfill Alarm

195. In Event submenu, select TANK drop down

196. Check the following boxes

• OVERFILL ALARM

197. Press checkmark to save any changes.

198. On Device tasks menu select Actions

199. Press Add Task

200. Set Device as RELAY 2: Alarm Output

201. In Event submenu, select LIQUID SENSOR drop down

202. Check the following boxes

• FUEL ALARM

• SENSOR OUT ALARM

• SHORT ALARM

• WATER ALARM

• LIQUID WARNING

203. In Event submenu, select MAG SENSOR drop down

204. Check the following boxes

• COMMUNICATION ALARM

• SENSOR FAULT ALARM

• FUEL WARNING

• FUEL ALARM

• WATER WARNING

• WATER ALARM

• HIGH LIQUID WARNING

• HIGH LIQUID ALARM

• INSTALL FAULT

205. In Event submenu, select TANK drop down

206. Check the following boxes

• SETUP DATA WARNING

• LEAK ALARM

• HIGH WATER ALARM

• LOW PRODUCT ALARM

• SUDDEN LOSS ALARM

• PROBE OUT

• HIGH WATER WARNING

• DELIVER NEEDED

• GROSS TEST FAIL

• PERIODIC TEST FAIL

• CSLD IDLE TIME

• CSLD RATE INCR WARNING

207. Press checkmark to save any changes and press Next

208. On Print Tasks menu, Press next

209. On All Tasks menu, Press Next

210. On Roles Admin menu, Press Next

211. On Users Admin, select Actions

212. Press Add User

213. Set Username to WFSM

214. Set Fullname to Fuels

215. Set Role to Administrator

216. Set Email to Wing ORG email

217. Set Password to 450plus

218. Press checkmark to save any changes and press Next

219. On Security menu Set front panel security to DISABLED

220. Set Serial Command Port to DISABLED

221. Set SSH Port to DISABLED

222. Set serial command over SSH to DISABLED

223. Set HTTPS Port (WEB ACESS) to DISABLED

224. Set User admin via web to DISABLED

225. Press checkmark to save any changes and press Next

226. Exit Set up Wizard

227. Ensure printer has paper

File details come from the government source that posted it. Updated .