Exhibit G Specifications Crawler Dozer w Angle Blade.docx

State of Illinois Department of Central Management Services

Specifications for Crawler Dozer w/ Angle Blade Exhibit G Specifications for Crawler Dozer w/ Angle Blade

The following specifications describe the minimum requirements for a track type dozer with angle blade of Low Ground Pressure (LGP) design for use in ditch work and slope maintenance. The equipment shall be new, of current design and manufacture, and a production model. Any additions, deletions, or variations from the following specifications must be noted or the equipment will be rejected. Any standard items appearing in the manufacturer’s regular published specifications shall be included unless otherwise noted.

Parts and service for the equipment should be readily available within the State of Illinois.

Unless otherwise specified, the equipment shall be complete in all parts and ready for immediate use upon delivery.

Make:

Model:

Manufacturer:

The State reserves the right to waive minor informalities, deficiencies, or technical variances which by their nature are restrictive to a given manufacturer, if in its’ judgement, it would be in the best interest of the State.

Dozer:

The power angle dozer shall be furnished as a Low Ground Pressure (LGP) machine with all attachments called for to be controlled by the operator from the cab. The attachments shall be “Industry standard” capable of functioning with dozer specified.

The dozer blade furnished must be heavy duty, smooth edged, minimum 120” wide with moldboard height of approximately 33” including a replaceable cutting edge. The moldboard shall be a 6-way function with variable pitch, all functions hydraulically powered and controlled by the operator. The blade shall also be equipped with a “shaker” to dislodge sticky material accumulating on the moldboard. The machine shall also include a “stable blade” feature.

The moldboard shall have an SAE rated capacity minimum of 2-cu.yd.

The machine shall be furnished with an integrated grade control and slope assist feature, when engaged shall provide the operator the ability of maintaining pre-established blade angles for the grade. The system shall store the input and return to the settings at the operator’s command.

Ground pressure shall be ±5.0 psi. equipped as specified.

Track on ground shall be 88" minimum.

The dozer shall have industry standard LGP track width of 26” Minimum.

The dozer shall have a solid mounted carriage and a minimum of 6 lower support rollers.

The machine shall include sealed lubricated track rollers and the track shall include a hydraulic adjustment feature The tracks shall include closed, single steel bar type grousers with approximately 39 shoes per side.

Ground clearance shall be 13” minimum.

The blade shall provide a ±25° angle to the left and to the right.

The blade shall also provide approximately 30” of lift height blade tilt of maximum of 15”. The blade shall also include a “blade shaker” to allow the operator to shake off material stuck to the moldboard.

Engine:

The unit shall be provided with a current production, liquid cooled, turbo-charged, diesel engine with a net horsepower measured by SAE 1349 standards at a minimum of 100hp and minimum Interim Tier 4 Emissions.

Diesel engine controls, features, instruments, or LCD screen monitors for the following:

· Tachometer

· Fuel gauge.

· DEF gauge if equipped.

· Engine-coolant temperature gauge or warning light.

· Engine oil pressure gauge or warning light.

· Hand or foot-controlled throttle

· Air filter restriction gauge or warning light.

· Back-up alarm

· Hydraulic oil temperature

· Hour meter

· Engine/hydraulic system shutdown

· Cold weather starting aid

· Coolant heater Audible alarms or warning lights shall be included for the following:

· Engine coolant temperature

· Transmission charge temperature

· Engine oil pressure

· Hydraulic oil temperature

· Seat belt reminder

· Engine air filter restriction

Fuel:

Fuel capacity 40 gallons or manufacturer recommended for engine provided.

Fuel tank or cap clearly labeled "Diesel Fuel Only" and be locking or securable.

Electrical System:

The loader shall be equipped with a 12 or 24-volt electrical system. The battery, starter, and alternator shall be rated for the engine supplied and able to handle any additional electrical accessories. If a 24-volt system is used, it must include two (2) 12-volt circuit taps to accommodate the ordering entity’s communications and electronics.

Drive System:

The transmission shall be variable tandem hydrostatic piston pumps with two (2) fully reversing hydrostatic motors. Travel speeds shall be controlled by an auto-shift feature for high/low utilizing an auto or power shift feature. These functions shall include both forward and reverse directions.

Variable speed hydrostatic forward or reverse. Steering, braking, forward and reverse movement controlled by the operation of two hand levers or joystick(s).

Top ground speed shall be approximately 5.5 mph per hour.

Hydraulics:

Dozer hydraulics shall include pump, hydraulic cooler, filtration, variable flow, and maximum flow auxiliary hydraulics, with necessary valves and controls to run accessory attachments. The dozer hydraulics shall be rated to operate the optional accessories purchased with the unit.

Operator’s Cab:

The cab shall be manufacturer’s deluxe fully enclosed cab with sound suppression and lockable door(s). The cab shall be constructed to incorporate an OSHA approved and SAE rated ROPS/FOPS protection structure.

The cab shall be fully enclosed with lockable doors and removable front window.

Operator controlled window wiper/washer system shall be provided.

The side windows shall open and may be removable.

The operator’s seat shall be fully adjustable suspension type either air or mechanical, and provide adjustment for leg room, height, reach, weight, and lumbar support. Seatbelt with warning indicator shall be included.

The cab shall include manufacturer’s standard circulated Air conditioning/heater/defroster and controls.

The operator’s cab shall include vibration dampeners and Manufacturer’s standard sound suppression treatment.

The track loader shall be provided with a rear-view camera and display for the operator to see what is to the rear of the machine.

The cab shall include a full protection package including:

· Front sweeps

· Rear A/C guard

· Rear cab window screen protector

The operator’s station shall feature the following:

· Locking security covers for the gauges and dash features (if available).

· Horn

· Radio AM/FM/AUX/USB/Bluetooth

· Power point

· Slope indicator

· Seat belt

· Operator controls adjustable front to rear

· Parking brake control

· Gauges or LCD display for engine data

· Slow moving vehicle emblem

· Backup alarm

· Storage compartment

· Cup holder Lighting:

The unit shall be equipped with front and rear high intensity lighting for nighttime operations.

The unit shall be equipped with an Amber LED warning strobe system.

Winch:

A hydraulic powered winch shall be mounted on the rear of the machine and controlled by the operator from the cab.

The winch shall have a fairlead and four (4) rollers, and a bare drum line pull rating of approximately 85,000 pounds.

The winch shall be rated for .875-inch diameter wire rope and the winch shall include 190 feet of wire rope with slip hook at the end of the cable rated to the capacity of the winch.

Finish:

All exterior surfaces normally powder coated or painted shall be manufacturer's standard color.