Exhibit E Specifications for Compact Track Loader.docx

State of Illinois Department of Central Management Services Specification for Compact Track Loader

Exhibit E Specifications for Compact Rubber Track Loader

The following specifications describe the minimum requirements for a compact rubber track-type loader aka skid steer. The equipment shall be new, of current design and manufacture, and a production model. Any additions, deletions, or variations from the following specifications must be noted or the equipment will be rejected. Any standard items appearing in the manufacturer’s regular published specifications shall be included unless otherwise noted.

Parts and service for the equipment should be readily available within the State of Illinois.

Unless otherwise specified, the equipment shall be complete in all parts and ready for immediate use upon delivery.

Make:

Model:

Manufacturer:

The State reserves the right to waive minor informalities, deficiencies, or technical variances which by their nature are restrictive to a given manufacturer, if in its’ judgement, it would be in the best interest of the State.

Loader:

The loader shall be furnished with an attachment quick coupler controlled by the operator from the cab. The quick coupler shall be “Industry standard” capable of functioning with existing attachments and any required by the specifications.

The loader shall be furnished with a heavy duty, smooth edged, minimum 80” wide dirt bucket with a replaceable cutting edge.

The bucket shall have an SAE rated heaped capacity of approximately 21 cu. ft.

The rated operating capacity of the loader as specified shall be a minimum 3,800 lbs. at 50% of tipping load.

Ground pressure shall be approximately 4.2 to 4.5 lbs./psi.

Track on ground shall be 63" minimum.

The loader shall have industry standard track width approximately of 17.7”.

The loader shall have a solid mounted carriage and a minimum of 4 lower support rollers.

Bucket pin height at max lift shall be a minimum of 125”.

Ground clearance shall be 8.5” minimum.

The loader shall include provisions, controls, and all accessories to ensure the operation of a hydraulic hammer of a size the manufacturer rates for this machine.

Note: The heavy-duty dirt bucket shall be used to determine the specification ratings of the loader.

Engine:

The unit shall be provided with a current production, liquid cooled, turbo-charged, diesel engine with a gross horsepower minimum of 90hp.

The engine shall be compliant with all present clean air regulations and include all Tier 4 emission standards.

Diesel engine controls, features, instruments, or LCD screen monitors for the following:

· Tachometer

· Fuel gauge.

· DEF gauge if equipped.

· Engine-coolant temperature gauge or warning light.

· Engine oil pressure gauge or warning light.

· Hand or foot controlled throttle

· Air filter restriction gauge or warning light.

· Back-up alarm

· Hydraulic oil temperature

· Hour meter

· Engine/hydraulic system shutdown

· Cold weather starting aid

· Coolant heater Audible alarms or warning lights shall be included for the following:

· Engine coolant temperature

· Transmission charge temperature

· Engine oil pressure

· Hydraulic oil temperature

· Seat belt reminder

Fuel:

Minimum fuel capacity 25 gallons.

Fuel tank or cap clearly labeled "Diesel Fuel Only."

Electrical System:

The loader shall be equipped with a 12-volt electrical system. The battery, starter, and alternator shall be rated for the engine supplied and able to handle any additional electrical accessories.

Drive System:

The transmission shall be variable tandem hydrostatic piston pumps with two (2) fully reversing hydrostatic motors. Travel speeds shall be controlled by an auto-shift feature for high/low utilizing an auto or power shift feature. These functions shall include both forward and reverse directions.

Variable speed hydrostatic forward or reverse. Steering, braking, forward and reverse movement controlled by the operation of joystick(s).

Top ground speed shall be a minimum of 6.0 mph per hour.

The loader shall include a speed sensitive “ride control” feature to prevent the front to rear rocking motion while “roading” the machine.

Hydraulics:

Loader hydraulics shall include pump, hydraulic cooler, filtration, variable flow and maximum flow auxiliary hydraulics, with necessary valves and controls to run accessory attachments. The loader hydraulics supplied shall be rated to operate any optional accessories purchased with the unit.

The machine shall be equipped with standard and high flow hydraulic system. This system shall feature a minimum of 20/32 gpm at a minimum pressure of 3,050 psi. This system shall be capable of providing this level of performance without over-heating for extended lengths of time.

Note: These are the minimum requirements for the hydraulic tool circuits required with the machines to be provided. These loaders may be equipped with large rotary planers and used for long durations for planing asphalt.

All hydraulic cylinders shall be double acting type. The tilt cylinders shall have a cushioning feature on the dump and rollback.

Operator Cab:

The cab shall be manufacturer’s deluxe fully enclosed cab with sound suppression and lockable door(s). Cab shall be constructed to incorporate an OSHA approved and SAE rated ROPS support structure.

The cab shall include manufacturer’s standard circulated air conditioning/heater/defroster and controls.

The loader shall be provided with rear view camera for the operator to see what is to the rear of the machine.

The operator’s seat shall be fully adjustable air suspension type and provide adjustment for leg room, height, reach, weight, and lumbar support. Seatbelt with warning indicator shall be included (i.e. Fasten seatbelt).

Cab features shall include the following:

· Locking Safety type entry door (ballistic polycarbonate/Lexan for Forestry Mulcher option)

· Selectable joystick functions for attachments

· Horn

· Dome light

· 12-volt Power point (socket/USB)

· Seat belt

· Seat bar (if required by manufacturer)

· Parking brake control

· Sound reduction

· Washer/wiper system

· AM/FM Radio with Bluetooth connectivity

· Gauges or LCD display for engine data

· Slow moving vehicle emblem

· Backup alarm

Lighting:

The unit shall be equipped with front and rear high intensity lighting for night time operations.

The unit shall be equipped with an Amber LED warning strobe system.

Finish:

All exterior surfaces normally powder coated or painted shall be manufacturer's standard color.

Common attachments that might be purchased under accessories/factory modification:

84” Heavy Duty Bucket heavy duty dirt bucket with replaceable bolt on cutting edge.

84” Combination 4 in 1 Bucket 82” Root Grapple 78” or larger Industrial Grapple Bucket 48” Pallet forks with Heavy Duty Carriage Frame 60” Forestry/mulching cutter with application kit and safety features.

Hydraulic hammer/breaker-Impact Energy Class minimum of 700 ft.-lbs.

Auxiliary rear hydraulics Rear bumper with winch mount and roller fairlead.

Recovery Winch 12,000 lb.

Full width angle broom 84” full with +/- 30 degrees left or right-angle operation.

84” sweeper shall contain all swept material with the capability of dumping into a truck bed.

Water kit with attachments.

40” Planer high flow design.

24” Planer high flow design.

Stump Grinder