Appendix B5 - Pre-Product Data.pdf

C&C Contractors 209 Lyons Street Notasulga, Alabama 36866 P: +13342574307

Project: 1901 1901 Alleghenies Major 2018 1158 Morgan Rd

Bridgeville, Pennsylvania 15017

Submittal #28 20 00-3.1 - Pre - Product Data 28 20 00 - Video Surveillance

Revision 1 Submittal Manager Jim Costner (C&C Contractors, LLC)

Status Open Date Created May 6, 2024

Issue Date May 6, 2024 Spec Section 28 20 00 - Video Surveillance

Responsible Contractor

Received From

Received Date Submit By

Final Due Date May 27, 2024 Lead Time

Cost Code

Location Type

Approvers Jim Costner (C&C Contractors, LLC), Joyce Johnson (Department of Veterans Affairs), Jim Costner (C&C Contractors, LLC)

Ball in Court Jim Costner (C&C Contractors, LLC)

Distribution Bob Floyd (C&C Contractors, LLC), Daniel Davidson (C&C Contractors, LLC), Adam Reichl (Vali Cooper International (VCI), LLC), Kim Koppenberg (Koppenberg Enterprises, INC)

Description 1.4 Submittals, Product Data - Fiber, Monitors, Rack, Signs

Submittal Workflow

Name Sent Date Due Date Returned Date Response Attachments

General Information Attachments

28 20 00-3.1 Updated Video Surveillance.pdf

Shane Levdansky May 6, 2024 May 13, 2024 Jun 10, 2024 Submitted DS150i REX.pdf HES9600-630.pdf HES4500.pdf Falcon_1790_Touchbar_Rim_Panic_Device _Installation_Instructions_107910.pdf Rack.pdf HID Standard Wall and Keypad Card Reader.pdf SS24A2EM-EN.pdf HID Keypad REader.pdf UB1270.pdf T8612 Axis.pdf UPS.pdf RS2_LP1502.pdf 2505A-L Door Contact.pdf Access Control Cable.pdf Wall Mount Panel for Access Control.pdf RS2_MR52-S3.pdf Axis 507-041.pdf

Comment Hello All, I am responding to this inquiry through Procore, but do want to confirm that I did submit these last month, when requested over email. Please let me know if you have any questions.

Jim Costner Jun 10, 2024 May 13, 2024 Jun 12, 2024 Approved

C&C Contractors Page 1 of 2 Printed On: Nov 11, 2024 03:51 PM EST https://app.procore.com/743331/project/submittal_logs/document_downloader?attachment_id=4764339499&item_id=54493894&item_type=SubmittalLog&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/document_downloader?attachment_id=4764339499&item_id=54493894&item_type=SubmittalLog&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756644963&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645002&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645008&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645010&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645010&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645013&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645015&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645015&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645070&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645083&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645091&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645098&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645108&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645114&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645132&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645151&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645160&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645163&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet https://app.procore.com/743331/project/submittal_logs/54493894/submittal_log_approvers/document_downloader?attachment_id=4756645170&item_id=126933468&item_type=SubmittalLogApprover&project_id=743331&source=coversheet

Name Sent Date Due Date Returned Date Response Attachments

Joyce Johnson Jun 12, 2024 May 27, 2024 Aug 14, 2024 For Record Only

Comment Per the subcontractor:

Hello All, I am responding to this inquiry through Procore, but do want to confirm that I did submit these last month, when requested over email. Please let me know if you have any questions.

Information was provided via email and the VA's mod A00050.SA-32.

Are there additional questions?

Jim Costner Aug 14, 2024 May 27, 2024 Pending

Submittal #28 20 00-3.1 - Pre - Product Data Project: 1901 1901 Alleghenies Major 2018

C&C Contractors Page 2 of 2 Printed On: Nov 11, 2024 03:51 PM EST

SUBMITTAL TRANSMITTAL

SN: 28 20 00-3.1

Sheet:

DEPARTMENT OF

VETERANS AFFAIRS

PROJECT: National Cemetery of the Alleghenies- Phase 3 Development

CONTRACT NO: 36C10F19C0002

Obligation No. 925CM20006

Pkg.

No.

x

Date:

06-12-24

Contractor: C & C Contractors, LLC Supplier: Vantage Electric VA ACTION

Ite m

N o.

Specification Section No.:

Registered Submittal No.:

Pa ra gr ap h

Description of Item (Size, Type, Name, Manufacturer, Use, etc.) N o.

o f C op ie s Su bm itt ed o f

C op ie s

R et ur ne d

Ap pr ov

Ap pr w ith ot at io ns

D is ap pr

R es ub m it

28 20 00 Video Surveillance 1 1.4 Submittals 2 A Product data – Updated per MIS Contractor Signature:

Recommended By:

Title, Date: Project Manager 06-12-24

Title: Date:

I hereby certify that this submittal has been reviewed for accuracy, completeness, and compliance with contract requirements per the General Provisions (FAR 52.236-21) A/E/Sub:

Review Comments:

Action By:

Date:

Contracting Officer’s Representative

Approval of this submittal is subject to the provisions of the contract drawings and specifications. This action is for general concurrence only and the Government is not responsible for errors or omissions.

SUBMITTAL LOG DATES: From contractor (_________), To reviewer (_________), From reviewer (_________), To contractor (_________), DSC-1(CS) Rev.

Distribution: ( ) Contractor ( ) DSC File ( ) COR ( ) A/E ( ) DSC Interim ( ) COR Interim ( ) Contractor Interim 11/95

Product Data Sheet

2505A-L Industrial aluminium surface mount with steel armored cable

Industrial Contact

The Sentrol 2500 series are designed to be installed in commercial and industrial environments where a rugged sealed unit is required. It is ideal for metal doors, overhead doors, fences and gates. Each model features a high strength extruded aluminum housing and is completely encapsulated in Sentrol's exclusive polyurethane potting compound.

Durability and dependability

The Sentrol high performance magnetic contacts have been designed to facilitate installation and ensure durability and dependability. Most are conservatively rated at 10,000,000 cycles, guaranteeing a long life. Every reed connection is hand soldered and each magnetic contact is tested before they leave the factory, 100% of the time.

High quality components and materials

Reed legs are plated with rhodium or ruthenium, and hermetically sealed in dry nitrogen. This offers superior protection against sticking and provides a moisture free environment therefore preventing corrosion.

Standard Features

Mounting brackets available for gates, garage door and freezers

E

Rugged construction for a longer lifeE Convenient surface mountingE 2507AH series is polarity-sensitive with reference to magnet direction

E

2505A-L Industrial aluminium surface mount with steel armored cable

Specifications Gap distance (max) 76 mm

Connections 90 cm stainless steel armored cable

Contact NC

Supervised loop No

Dimensions (L x W x H)

Contact 76 x 13 x 25 mm

Magnet 76 x 13 x 25 mm

Color Aluminum

Remarks

Ordering Information Part No. Description

Industrial aluminium surface mount with steel armored cable2505A-L

As a company of innovation, UTC Fire & Security reserves the right to change product specifications without notice. For the latest product specifications, visit UTC Fire & Security online or contact your sales representative.

IPS-HQ-2505A-L-2012-11-16 11:01:36

All specifications referenced are nominal measurements unless otherwise noted.

T 800.379.1191 | www.smartwire.com | © Copyright 2014 Windy City Wire, Inc. | All rights reserved.

PART NUMBER 4ELEMP-YLW

UL Listed and Rated Type CMP Plenum Composite Cable

CABLE SPECIFICATIONS

DESCRIPTION Elem1:18 AWG 4 Conductor Bare Copper White Jacket with Purple Stripe;

Elem2:22 AWG 3 Pair OAS Bare Copper White Jacket with Yellow Stripe;

Elem3:22 AWG 2 Conductor Bare Copper White Jacket with Green Stripe;

Elem4:22 AWG 4 Conductor Bare Copper White Jacket with Red Stripe Plenum Composite Cable, C(UL)US CMP

CONDUCTOR Element 1: 18 AWG 7 Strand Bare Copper;

Element 2, 3, and 4: 22 AWG 7 Strand Bare Copper

INSULATION All Elements: .008" Low Smoke PVC

COLOR CODE Element 1: Black/Red/White/Green Element 2: Black/Red; White/Green; Brown/Blue Element 3: Black/Red Element 4: Black/Red/White/Green

SHIELD Element 1,3, & 4: N/A; Element 2: Overall Aluminum Mylar

DRAIN WIRE Element 1,3 & 4: N/A; Element 2: 24 AWG 7 Strand Tinned Copper

JACKET Inner Jackets: All Elements: Low-Smoke PVC .018"; Outer Jacket: Low-Smoke PVC .020"

JACKET COLOR Yellow Jacket

MARKING Elem1: LOCK POWER A B C D E 0 1 2 3 4 5 6 7 8 9; Elem2: CARD READER A B C D E 0 1 2 3 4 5 6 7 8 9; Elem3: DOOR CONTACT A B C D E 0 1 2 3 4 5 6 7 8 9; Elem4: REX/SPARE A B C D E 0 1 2 3 4 5 6 7 8 9 Outer Jacket: SMARTWIRE ACCESS CONTROL CABLE DOOR / ZONE A B C D

E 0 1 2 3 4 5 6 7 8 9 C(UL)US CMP ROHS MADE IN THE USA

OVERALL DIAMETER Elem1: .184" Nom.; Elem2: .207" Nom.; Elem3: .126" Nom.; Elem4: .145" Nom; Outer Jacket: .415" Nom.

CABLE WEIGHT 108 Lbs/Mft.

CAPACITANCE Elem 1: 27 pF/Ft. Nom.; Elem 2: 51 pF/Ft. Nom.; Elem 3: 20 pF/Ft. Nom.; Elem 4: 20 pF/Ft.

IMPEDANCE Elem 1: 70 Ohms; Elem 2: 27 Ohms; Elem 3: 94 Ohms; Elem 4 96 Ohms

DC RESISTANCE Element 1: 6.66 Ohms/Mft. maximum @ 20 C Element 2: 16.9 Ohms/Mft. maximum @ 20 C Element 3: 16.9 Ohms/Mft. maximum @ 20 C Element 4: 16.9 Ohms/Mft. maximum @ 20 C

TEMPERATURE RATING 0 C to 75 C / 300 Volt

INDUSTRY STANDARDS

FLAME RATING Approved For Plenum Use Without Conduit Per NFPA 262 Flame Test

AGENCY APPROVALS NEC Article 800; UL Listed C(UL)US CMP, RoHS Compliant, Made in the USA

AXIS T8604 Media Converter Switch Converts Ethernet to fiber 12 V DC

AXIS T8604 Media Converter Switch allows Axis video products to connect to the network using standard network or fiber optic cables that help lower the cost of installing the cameras over long distances.

Perfect for city surveillance, airports and other long dis-tance installations, AXIS T8604 Media Converter Switch is a DIN-mounted device that can convert an Ethernet signal to be used over optical fiber cable. Surveillance in-tegrators in the field can also connect installation moni-tors and laptops to AXIS T8604 for camera maintenance and control.

The media converter switch can be connected in a daisy chain network. The maximum number of cameras that can be connected in the daisy chain depends on the generated bitrate per camera. The limitations are the 100 Mbit link between camera and media converter switch, and the 1000 Mbit link between the media converter switches. AXIS T8604 does not feature IGMP Snooping.

An Axis camera/encoder connects to AXIS T8604 us-ing an Ethernet cable, and through the media converter switch and data is provided to the network video prod-uct. Two SFP slots give installers the flexibility to con-nect the cameras cost-effectively to the network over long distances. The RJ45 connectors can also be used for connection to complementary cameras or temporar-ily to a laptop to service the system locally.

DATASHEET

> Convert Ethernet to optical fiber

> Compatible with Axis network video products

> Support for 10/100 Mbps

> Two SFP slots and two RJ45 ports

Technical Specifications - AXIS T8604 Media Converter Switch Models AXIS T8604 Media Converter Switch

General Supported cameras

All Axis network video products

Casing Metal Color: White NCS S 1002-B

Power 12.0-13.2 V DC, max. 3.5 W (power supply not included)

Connectors 2x RJ45 connectors (10/100 Mbps)a 2x SFP connectors (100/1000 Mbps) for SFP fiber optic modules or SFP to copper modules 1x power

Display and indicators

Power LED indicator Network LED indicator (4x)

Compliance RoHS, REACH, WEEE, CE, EN 50022, IEC 60715, AS 2756

Mounting DIN Rail mount

Environment Indoor/Cabinet

Operating conditions

-40 °C to 75 °C (-40 °F to 167 °F) Humidity 10-85% RH (non-condensing)

Storage conditions

-40 °C to 75 °C (-40 °F to 167 °F) Humidity 10-85% RH (non-condensing)

Approvals EN 55022 Class A, EN 61000-3-2, EN 61000-3-3, EN 61000-6-1, EN 61000-6-2, EN 55024, FCC Part 15 Subpart B Class A, ICES-003 Class A, VCCI Class A, C-tick AS/NZS CISPR 22, KCC KN22 Class A, KN24, IEC/EN 60950-1

Dimensions 150 x 100 x 30 mm (5.9 x 3.9 x 1.2 in)

Weight 284 g (0.63 lb)

Included accessories

Bracket Mount DIN Clip, Installation Guide

Warranty Axis 3-year warranty, see www.axis.com/warranty

a. Use shielded cables (STP) CAT5 or higher

More information is available at www.axis.com

AXIS T8604 Media Converter Switch

1.2x RJ45

2.2x SFP slots (fiber)

3.Power connector (DC input)

Typical setup

1.Camera 1

2.Camera 2

3.Optical Fiber Switch

4.AXIS T8604

5.Fiber slots #1/#2 (SFP)

6.Midspans

7.Power

8.Fiber

9.Cat5 cable www.axis.com

©2014 Axis Communications AB. AXIS COMMUNICATIONS, AXIS, ETRAX, ARTPEC and VAPIX are registered trademarks or trademark applications of Axis AB in various jurisdictions. All other company names and products are trademarks or registered trademarks of their respective companies. We reserve the right to introduce modifications without notice.

4/

EN

/M 1.

3/

Intrusion Alarm Systems - DS150i Series Request-to-exit Detectors

DS150i Series Request-to-exit Detectors u Single or double door use u Wall or ceiling mountable u Internal vertical pointability u Wrap-around coverage pattern u Selectable relay trigger mode u Selectable fail safe/fail secure modes

The DS150i Series consists of the DS150i Detector (light gray) and the DS151i Detector (black). They are specifically designed for Request-to-exit (REX) applications. The DS150i and DS151i detect motion in their coverage area and signal an access control system or door control device.

System overview

Functions Test Features Externally visible activation LED.

Regulatory information

Region Regulatory compliance/quality marks

Europe CE

CE EMC, LVD, RoHS [DS150i DS151i]

Russia GOST ТС N RU Д-NL.МН09.В.00334 EAC

Australia RCM [DS150i]

USA UL ALVY: Access Control Systems Units (UL294) [DS150i, DS151i]

Installation/configuration notes

4.5 m 0 m 4.5 m

0 ft

15 ft

15 ft 0 ft 15 ft

0 m

4.5 m

4.5 m 0 m 4.5 m

0 ft

15 ft

15 ft 0 ft 15 ft

0 m

4.5 m +14°

3 m 0 m 3 m

0 ft

5 ft

10 ft 0 ft 10 ft

0 m

1.5 m

-14°

Front View and Top Views

Intrusion Alarm Systems - DS150i Series Request-to-exit Detectors 2 | 2

A front view of the DS150i and DS151i coverage, as well as top views of the coverage pattern on the floor. The typical coverage measurements are

2.4 m x 3 m (8 ft x 10 ft).

0 m 1.5 m

5 ft

0 m 4.5 m 0 m

4.5 m 15 ft

15 ft

-14° +14°

0 ft0 ft

0 ft

Side View A side view of the DS150i and DS151i coverage pattern.

Parts included

Technical specifications Electrical

Current Draw: 26 mA at 12 VDC

Voltage: 12 VAC or VDC; 24 VAC or VDC

Mechanical

Alarm Output: Two Form C relay contacts

Indicators: One activation LED

Relay Latch Time: Adjustable to 60 sec

Enclosure Dimen-sions:

3.8 cm x 15.9 cm x 3.8 cm (1.5 in. x 6.25 in. x 1.5 in.)

Enclosure Mater-ial:

High impact ABS plastic enclosure

Power Loss De-fault Mode:

Programmable fail-safe or fail-secure modes.

Timer Mode: Programmable reset (accumulative) or non-reset (counting) mode.

Mounting Loca-tion:

Surface mount on wall or ceiling

Environmental

Operating Temper-ature:

-29°C to +49°C (-20°F to +120°F)

Radio Frequency Interference (RFI) Immunity:

No alarm or setup on critical frequencies in the range from 26 MHz to 1000 MHz at 50 V/m.

Ordering information DS150I Request-to-exit sensor For use in Request-to-EXit (REX) applications. Provides PIR, 2.4 m x 3 m (8 ft x 10 ft) coverage.

Order number DS150I | F.01U.364.858 F.01U.405.129 DS151I Request-to-exit sensor, black Black enclosure. For use in Request-to-EXit (REX) applications. Provides PIR, 2.4 m x 3 m (8 ft x 10 ft) coverage.

Order number DS151I | 4.998.800.237 F.01U.364.867 F.01U.405.130

Accessories TP160 Trim plate for DS150 and DS160 A light gray trim plate used when mounting the detector over a standard single-gang box.

Order number TP160 | 4.998.800.318 TP161 Trim plate for DS151 and DS161, black A black trim plate used when mounting the sensor over a standard single-gang box.

Order number TP161 | 4.998.130.552

Represented by:

Europe, Middle East, Africa: Germany: North America: Asia-Pacific:

Bosch Security Systems B.V.

P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 www.boschsecurity.com/xc/en/contact/ www.boschsecurity.com

Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Tel.: +49 (0)89 6290 0 Fax:+49 (0)89 6290 1020 de.securitysystems@bosch.com www.boschsecurity.com

Bosch Security Systems, LLC 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 onlinehelp@us.bosch.com www.boschsecurity.com

Robert Bosch (SEA) Pte Ltd, Security Systems 11 Bishan Street 21 Singapore 573943 Phone: +65 6571 2808 Fax: +65 6571 2699 www.boschsecurity.com/xc/en/contact/ www.boschsecurity.com

Data subject to change without notice | 202311161543 | V19 | November 16, 2023 © Bosch Security Systems 2023

*ININST.1001*

ININST.1001

Index:

• Before Installation

• Installation

• Touchbar Dogging

• RM170 Mullion Installation

• Field Sizing Device

• 2090 Retrofit Instructions

• Device Template

• Strike Template

• Touchbar Part Numbers

• Parts List

Rim Panic Device

1790 Touchbar Installation Instructions

Customer Service 1-877-671-7011 www.allegion.com

© Allegion 2017 Printed in U.S.A.

ININST.1001 Rev. 11/17-e

1. Check "Parts List" (see page 16).

2. Prepare door using template on page 14.

3. Prepare frame using template on page 15.

4. If door width is non-standard, cut device (see page 10).

1.1. Cut cylinder tailpiece to correct length.

BEFORE INSTALLATION

INSTALLATION

Install outside cylinder. (If no outside cylinder, go to Step 3.)1

If 5/32" spacer is used, as in Kawneer applications, cut length is 1-23/32" for a 1-3/4" thick door.

NOTE!

If necessary, change key function to hold back (HB).2

Device is set at factory for night latch (NL) function.

To convert to HB, perform Steps 2.1-2.3.

For NL function, skip Steps 2.1-2.3 and go to Step 3.

NOTE!

2.1. Remove the set screw from the drive

bushing assembly using 0.050" Allen wrench supplied in PKG.133.

2.2. Rotate internal drive bushing

counterclockwise until it stops against the internal stop.

2.3. Maintain position of drive bushing

and continue.

Set screw

Drive bushing assembly

0.050" Allen wrench

1.2. Install cylinder into door and secure

with two mounting screws. S crews must be flush with surface of door. Tailpiece cut length = door thickness D minus 3/16"

Cylinder mounting screws (2)

D

3.1. Start two hinge stile mounting screws (1/4-20 x 1/2" pan head) in channel end cap.

Leave screws loose.

Mount device.3

3.2. Slide device channel under channel end cap aligning channel slots.

3.3. If using outside cylinder, align drive bushing assembly over tailpiece maintaining drive bushing position.

Drive bushing assembly

Outside cylinder tailpiece

Bottom of device

Channel end cap

Hinge stile mounting screws

1/4-20 x 1/2" PPHMS

Lock stile mounting screws

1/4-20 x 3/4" PPHMS

3.4. Attach device to door at lock stile using two lock stile mounting screws (1/4-20 x 3/4" pan head) and tighten securely all four mounting screws.

Device channel

Channel end cap

Channel slots

4.2. Wire RX switch as shown below. For EL wiring, go to Step 4.3.

4.1. Drill 3/8" diameter hole for EL/RX wiring through channel end cap, channel, and inside face of door.

Prepare hole and wire EL/RX device. (If device is not EL/RX, go to Step 5.)4

Hole must be free of burrs.

NOTE!

3/8" drilled hole

Electric power transfer (EPT-2 part No. 012011

EPT-10 part No. 012012)

Switch shown not activated (touchbar not depressed)

Wiring must be pulled tight so cable will not interfere with touchbar and channel movement.

CAUTION!

Touchbar

NO

NC

C

Yellow

Red

Blue

RX switch (part No. WIRE.1001)

• The RX switch is activated when the touchbar is depressed.

• Use the Von Duprin EPT-10 power transfer (for three wires), EPT-2 power transfer (for two wires), electric hinge, electric pivot, or door loop to transfer the wiring from the door to the frame.

• Connect the power transfer wires and switch assembly wires with crimp connectors. Unused wires should be insulated separately.

The RX switch is available only as a factory installed item. Part No. WIRE.1001 can be used only to replace the factory installed RX switch.

NOTE!

4.3. Wire EL solenoid as shown below. All EL1790 devices are fail secure.

Voltage: 24 VDC Current: 16 A inrush (0.3 sec.)

0.25 A holding

Electrical Specifications

Solenoid must be wired to a PS914 power supply with a 900-2RS or Solenoid

Potted circuit board

12 AWG minimum, 200 feet maximum

Black Black

PS914

power supply

120-240 VAC - 2AMP

Outside control switchEL1790

Electric power transfer or pivot

NOTE!

Electric power transfer (EPT-2 part No. 012011

EPT-10 part No. 012012)

Wiring must be pulled tight so cable will not interfere with touchbar and channel movement.

CAUTION!

Potted circuit board

(part No. 050534-00)

Solenoid (part No. 971687-00)

Plunger (part No. PLUNGER.101)

The potted circuit board is a protection circuit. It disconnects power from the solenoid if the plunger does not seat within a specified time. To reset the protection circuitry, remove power from the solenoid and reapply.

900-4RL option board installed

Install covers.5

6.1. Apply strike to frame as shown. Tighten

screws marked A so strike is flush with front of blade as shown.

6.2. Drill and tap for screws marked B while

maintaining alignment of strike and blade stop.

6.3. Secure strike.

6.4. Place wear strip under front of strike and

mark two holes as shown.

6.5. Drill through two places with #10 drill for

wear strip mounting holes.

6.6. Install rivets to wear strip and frame and

secure with hammer.

6.7. Verify clearance between cover and strike

as shown.

5.1. Install center case cover with two cover screws (#8 x 5/8" FPHTC).

5.2. Install hinge stile end cap with two end cap mounting screws (#8 x 1-1/2" FPHTC).

See page 8 for mullion installation.

NOTE!

5/32" (face of strike to face of cover)

6 Install TD35 strike for non-mullion applications. (See pg. 13 for frame preparation)

Strike and blade flush

Wear strip

#10 drill 2 places

Rivets

7.1. Dog device. Latch bolt should clear strike roller when door is opened.

Perform functional check.7

Shimming may be required to maintain 5/32" dimension.

NOTE!

A

B A

B

Hinge stile end cap

End cap mounting screws

#8 x 1-1/2" FPHTC

Center case cover

Cover screws #8 x 5/8" FPHTC

Device must be undogged to install center case cover.

NOTE!

TOUCHBAR DOGGING

These instructions are for touchbar dogging of new style DOM 1790 devices. New style devices have two cover screws installed vertically into the center case cover. (Old style devices have four cover screws installed horizontally into the center case cover.)

NOTE!

EL (electric latch retraction) devices cannot be mechanically dogged using the touchbar. If mechanical hold back is required in addition to electric latch hold back, use the pull side HB key cylinder option.

NOTE!

1. Depress touchbar with hand and maintain pressure on touchbar.

2. Insert dogging key into hole on touchbar.

3. Rotate key approximately 1/8 turn clockwise.

4. Release pressure on touchbar (touchbar will remain depressed to door).

To Dog Device (hold latch retracted)

To Undog Device (panic latch locks upon closing)

1. Depress touchbar with hand and maintain pressure on touchbar.

2. Insert dogging key into hole on touchbar.

3. Rotate key approximately 1/8 turn counterclockwise.

4. Release pressure on touchbar (touchbar will extend from door).

2 4

2 4

1. Mount top and bottom fittings (see below). To install fittings, line up fittings with center of doorway and flush with doors. Cut out threshold to receive bottom fitting.

RM170 MULLION INSTALLATION

Top Fitting

1"

1/2"

1-11/16"

9/16"

1-5/8"

2-3/4"

1/2" filler by others (top fitting secured to filler)

3-1/2"

Face of mullion flush with face of stop

2-3/4"

7/8"

1-17/32"

2-1/4"

1-1/2" 11/32"

#21 drill and prep for

#10 x 1" FH

E xt er io r

Line of door stop door opening

1-1/8"

3-1/16"

View Showing Optional DOM Filler Plate

Bottom Fitting

13/16"

3/16" radius

/3

2"

1- 1/

Cut to line of door stop to receive bracket

7/8"

Prep for

#10 FH

Line of door stop door opening

View Showing Threshold Cutout

1-1/16"

Detail B

Top and bottom fittings must be used in correct position or strike center line will be incorrect.

NOTE!

Detail C

4-3/4"

1/32" clearance

42" Security clip

NOTE!

Mullion installed to floor. Do not mount to threshold

Detail A

Bottom fitting

Cut mullion 1/16" less than this dimension

3/4" reference

1/4" reference

Top fitting

2. Measure mullion and cut as required (Detail A). of strike is set at factory to match device template dimension of 42" to finished floor.

3. Slide mullion over top fitting and swing into position on bottom fitting (Detail B).

4. Slide mullion clamp over top fitting and secure with three screws.

5. Locate security clips on door (Detail C). Prepare holes with #21 drill and 10-32 tap and assemble.

A B

5. Remove two end cap screws, end cap, and touchbar.

6. Cut hinge side of touchbar to dimension B from Step 4.

7. Cover device mechanism to keep chips out and cut channel to dimension A from Step 2.

1/2" reference (when touchbar out)

A = door clear opening 2-27/32"

After removing, cut from this end

Channel

Touchbar

End cap

End cap screws

Measure to edge of extrusion

Standard Device Size Factory Dimension A Minimum Dimension A Minimum Dimension A 2' 6" 27.138" 21.138" 25.638" 3' 0" 33.138" 27.138" 31.638" 3' 6" 39.138" 33.138" 37.638" 4' 0" 45.138" 39.138" 43.638"

FIELD SIZING DEVICE

Note:These instructions assume a 1/2" blade stop on the door frame.

1. Determine door clear opening. This is the distance inside the frame.

2. Determine channel cut length A:

3. Verify that A determined in Step 2 is not less than minimum A dimension listed in table.

(Standard 1790 device sizes can be shortened by up to 6" and EL devices can be shortened by up to 1.5"). Cut channel.

4. Determine touchbar cut length B:

Standard Device EL Device

B = door clear opening 5-7/32"

9. Clean debris from touchbar and channel.

10. Slide touchbar over touchbar pins. Make sure to install both pins in lower slot in touchbar. If touchbar bracket is removed, it should be reinstalled with stop tabs turned up away from channel.

8. If hinge stile has not been prepared for channel hinge stile 1/4-20 mounting screws:

Place hinge stile end cap into hinge end of channel. Drill through the center of end cap slots using a letter "I" drill. These two holes will be used to transfer location of mounting screw holes to hinge stile when device is applied to door.

If hinge stile has been prepared for channel hinge stile 1/4-20 mounting screws:

Using end cut from channel in Step 3 as a template, place backs of channel sections against each other and align ends. Mark slot pattern on the cut-down channel. Following all safety precautions, use a drill and aluminum saw to cut slots in cut-down channel section.

Letter "I" drill through channel

2 places

Mark and cut slots

Piece cut from channel

Touchbar lower slot

Touchbar bracket (goes in lower slot)

Tabs point up as shown

Hinge stile end cap

Cut-down channel

11. Reinstall end cap and screws.

1. Remove crossbar device and door con studs from door as shown.

Note: Retrofitting double doors requires replacement of the RM70 mullion with a RM170 mullion. This is because they have different device center lines.

2090 RETROFIT INSTRUCTIONS

2-7/16"

Add #9 (0.196") drill, 1/4-20 tap, 2 holes (inside face only)

Existing door con stud hole

Existing pinion hole

Existing door con stud hole

3-13/16"

Existing door con stud holes

7/ 8"

1- 3/

4"

2. If door width is non-standard, size device using field sizing directions on page 10.

3. Using existing pinion or door con stud hole as a reference, locate the two 1/4-20 mounting holes on the lock stile. Drill and tap 1/4-20, inside face only.

Hinge stile

Lock stile

Door con studs (4)

Crossbar device

4. Mount the device to the lock stile using the supplied 1/4-20 x 3/4" pan head screws.

5. Position the device horizontally on the door (same distance from bottom of door to bottom of channel on both stiles).

6. Position channel end cap in end of channel and use to mark locations for hinge mounting holes.

7. Remove the device from the door.

8. Drill and tap through two 1/4-20 mounting holes on hinge stile, inside face only.

9. Remove the old 2090 strike and replace with TD35 strike (see Step 6 on page 6).

10. Continue on with 1790 installation instructions.

11. When installation is complete, install supplied set screw hole plugs in exposed 2090 door con stud holes (two on hinge stile and one on lock stile).

Lock stile mounting screws (2)

Channel end cap (use to mark mounting holes)

Channel equal distance to bottom of door on both sides

Hinge stile

Lock stile

Set Screw Hole Plugs Finish Part No.

US28 SCREW.1068 (pkg. of 3) DC13/DC35 SCREW.1067 (pkg. of 3)

Set screw hole plugs

DEVICE TEMPLATE

LHR shown RHR opposite

Pull side Push sideLock stile Hinge stile

13/16"

13/32"

1/4"

7/8"

7/8"

3/4"

3/8"

3/4"

Face of strike and stop or edge of mullion

1-3/16" dia.

outside face only for cylinder only

15/64" dia. drill and countersink with

15/16" dia. tool 2 holes (see Detail A) inside face only

9/16" dia.

inside face only

#7 drill and 1/4-20 tap

2 holes in lock stile inside face only

See Note D

Frame edge of device

Face of strike and stop or edge of mullion

Frame edge

Door clear opening

42" to finished floor (standard for

DOM 1790)

#7 drill and 1/4-20 tap 2 holes in hinge stile inside face only

Detail A (for cylinder)

5/16" dia.

x 82° countersink

3/64"

1. All holes inside face only except as noted.

2. All dimensions for 1-3/4" thick, 1/8" wall doors. Consult factory for others.

NOTES!

Dimensions from face of door blade stop to mounting hole center lines 3/4" minimum.

NOTE D!

STRIKE TEMPLATE

DC13

DC35

US3

US10

US26

US26D

US28

30" Nominal Device Length (24.785" Extrusion Length)

Finish Without Dogging

Hole

With Dogging

Hole

EXT.399 EXT.609

EXT.400 EXT.631

EXT.2324 EXT.2355

EXT.2334 EXT.2356

EXT.2339 EXT.2357

EXT.2289 EXT.2358

EXT.398 EXT.608

36" Nominal Device Length (30.785" Extrusion Length)

Without Dogging

Hole

With Dogging

Hole

42" Nominal Device Length (36.785" Extrusion Length)

Without Dogging

Hole

With Dogging

Hole

EXT.439 EXT.736

EXT.441 EXT.737

EXT.2341 EXT.2359

EXT.2345 EXT.2360

EXT.2349 EXT.2361

EXT.2350 EXT.2362

EXT.438 EXT.646

48" Nominal Device Length (42.785" Extrusion Length)

Without Dogging

Hole

With Dogging

Hole

EXT.443 EXT.739

EXT.444 EXT.740

EXT.2298 EXT.2363

EXT.2303 EXT.2364

EXT.2304 EXT.2365

EXT.2294 EXT.2366

EXT.442 EXT.738

EXT.825 EXT.828

EXT.826 EXT.829

EXT.2323 EXT.2351

EXT.2333 EXT.2352

EXT.2338 EXT.2353

EXT.2340 EXT.2354

EXT.830 EXT.827

TOUCHBAR PART NUMBERS

#26 drill and 10-32 tap

5/32" radius 4 places

42" to finished floor (standard for DOM 1790)

Measured from front of blade of device

Package No. 4270107393 Item Quantity Description Part No.

1 1 Strike 4270107227 2 1 Shim SHIM.150 3 1 Wear strip 4270109590 4 2 #10 x 1" FPHSMS 4270104524 5 2 Drive rivet 4299101022

Package No. ECAP.130 Item Quantity Description Part No.

6 2 1/4-20 x 1/2" PPHMS 4299100074 7 1 Channel end cap ECAP.127 8 1 Hinge stile touchbar end cap ECAP.128 9 2 #8 x 1-1/2" FPHTC 4270104557

Package No. COVER.120 Item Quantity Description Part No.

10 1 Center case cover COVER.106 11 2 #8 x 5/8" FPHTC SCREW.1056

Package No. PKG.133 Item Quantity Description Part No.

12 2 1/4-20 x 3/4" PPHMS 964221-89 13 1 0.050" Allen wrench 4270109548 14 1 5/32" hex dogging key 4270106944

Package No. 179CA Item Quantity Description Part No.

15 1 Slider SLIDER.101 16 1 Drive bushing CAMASY.101

Note: These parts are optional and are required with a rim cylinder. When installed at the factory, these parts are oriented for NL/HB operation. To convert from EO to NL or HB operation, use this kit and a rim cylinder.

Item Quantity Description Part No.

17 1 Channel spacer SPACER.107 18 2 #10-16 x 3/8" UFPHMS SCREW.1036

(DC13 or DC35) or

2 #10-16 x 3/8" UFPHMS SCREW.1026

(US28)

19 2 #8 x 3/4" FPHTF 4270109556 20 1 Latch bolt pin 969467-89 21 1 Retaining ring 964066-89 22 2 Touchbar pin PIN.125 23 2 Touchbar anchor BRKT.128 24 1 Lock stile touchbar end cap ECAP.129 25 1 Dogging spring 971493-89 26 1 Dogging assembly KIT.1022

(DC13 or DC35) or Dogging assembly KIT.1021

(US28)

PARTS LIST

RHR

shown

9 8

6 14

17 18

RIM CYLINDER

(optional; sold separately)

Finish Part No.

DC13 4270107367

DC35 4270105986

US4 032210-10

US10 032210-06

US26/28 4270100247

1. See page 15 for touchbar part numbers.

2. Touchbar shown cut away for visibility.

NOTES!

4500C Series Electric Strike Complete Pac

The 4500C series electric strike is designed for installation in 2" UL 10C fire rated frames with 1/2" drywall penetration. The 4500C features a low profile 1-3/8" depth, heavy-duty stainless steel construction. Its strength is derived from a unique keeper pin locking design, enabling the 4500C to exceed the ratings of the frame, door and locking hardware.

Low Profile

• Maintains 1/2" drywall penetration, even in a 2" UL 10C fire-rated frame

• Strike body depth 1-3/8"

• Unique keeper locking pin design

Heavy Duty Construction

• Exceeds ratings for most frames, doors and locking hardware

• Stainless steel construction

• ANSI/BHMA A156.31, Grade 1

Convenient & Versatile

• Includes two faceplates to accommodate either cylindrical or mortise locksets up to a 3/4" throw latchbolt

• Full keeper shims for horizontal adjustment

• Field selectable fail secure/fail safe

Printed in the U.S.A. Patent pending and/or patent www.assaabloydss.com/patents

Copyright © 2022, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.

All rights reserved. Reproduction in whole or in part without the express written permission of Hanchett Entry Systems, Inc. is prohibited. HES-98-0922

800 626 7590 | hesinnovations.com 10027 S. 51st Street, Ste. 102 Phoenix, AZ 85044 USA

How to Order

SERIES FINISH OPTION (S)

4500C – 630 – LBM

4500C Complete Electric Strike; includes faceplates for cylindrical and mortise locks 605 Bright Brass (blank) No Monitor 606 Satin Brass LBM Latchbolt Monitor 612 Satin Bronze LBSM Latchbolt Strike Monitor 613 Bronze Toned 629 Bright Stainless Steel 630 Satin Stainless Steel

Features

• Stainless steel construction

• Tamper resistant

• Static strength 1,500 lbs.

• Dynamic strength 100 ft-lbs.

• Endurance 1,000,000 cycles

• Field selectable fail safe/fail secure

• Two faceplates provided to accommodate a variety of locksets

• Non-handed

• Internally mounted solenoid

• Accommodates up to a 3/4" latchbolt

• Strike body depth 1-3/8"

• Plug-in connector

• Trim enhancer

• Full keeper shims for horizontal adjustment

• Dual voltage 12 or 24 VAC/VDC

Certifications

• ASTM E152 Fire Door Compliant

• ANSI/BHMA A156.31, Grade 1

• CAL FIRE, 3776-1654:0100

• NFPA-252 fire door Compliant

• California State Fire

Marshal Listed (old)

• UL 1034 Burglary-Resistant Listed

• UL 10C Fire-Rated, 3 Hour Single

Door [Fail Secure Only]

• UL 294 Listed

Specifications Frame Application

• Metal

• Wood

Electrical

• .24 Amps at 12 VDC/VAC

• .12 Amps at 24 VDC/VAC

• DC continuous duty

AC intermittent duty only

Options

• LBM - Latchbolt monitor

• LBSM - Latchbolt strike monitor

Accessories

• 157 Torx® screws

• 150 Strike Latch Guard

• HESCUT-MTK Metal Template Kit

• 2005M3 SMART Pac® III

• 4500-105 Trim Enhancer

• 4500-110 Replacement Strike Plate

• 4500-131 Filler Block

• 2001M Plug-in Bridge Rectifier

• 2004M ElectroLynx® adapter

• 2006M Plug-in Buzzer

• 4501-1/2 Lip Extension

• 4501-1 Lip Extension

Dimensions

El ec tr ic S tr ik es

The stylish windstorm resistant, surface mounted solution.

The 9600 Series Electric Strike is a windstorm resistant, surface mounted electric strike designed to accommodate rim exit devices with a 3/4" throw Pullman latchbolt. All components are completely encased within its 3/4" thick stainless steel housing, so no cutting on the frame is required for installation. Simply place the electric strike on the surface of the frame, align it with the exit latchbolt and install.

Adjustments have never been easier as the base is now separate from the cover.

It is field selectable for fail secure or fail safe operation, and for 12 or 24 VDC.

The 9600 is a surface mounted electric strike designed with the strength and durability required to exceed the severe forces of ANSI Windstorm testing.

Features Standard Features

• Installs in metal or wood frames

(wood screws not included)

• Separate base and decorative cover for easy adjustments

• Stainless steel construction

• Tamper resistant

• Static strength 2,000 lbs

• Dynamic strength 120 ft-lbs

• Endurance 1 million cycles

• Field selectable fail safe/fail secure

• Horizontal adjustment

• Non-handed

• Internally mounted solenoid

• Accommodates up to 3/4" [19mm]

Pullman latch

• SecuriCare five-year, no-fault, no questions asked warranty (Addition of SMART Pac® III extends the warranty to 10 years)

Optional Features

• LBM Latchbolt monitor

• LBSM Latchbolt strike monitor

Accessories

• 9000-116-XXX 1/16" Spacer plate

(Available in 613E, 628E, 630 & BSP finishes)

• 9000-108-XXX 1/8" Spacer plate (Available in 613E, 628E, 630 & BSP finishes)

• 9000-MTK Metal template kit

• SMB Surface mounting box

• 2001M Plug-in bridge rectifier

• 2004M ElectroLynx adapter

• 2005M3 SMART Pac III

• 2006M Plug-in buzzer

• 9000-ASB-XXX Aluminum

Spacer Bracket (availible 613E, 628E, 630 & BSP finis)

Surface Mounted Electric Strike Works with rim exit devices with a 3/4" throw Pullman latchbolt

Updated 7/31/23 Patent pending and/or patent www.assaabloydss.com/patents Copyright © 2023, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Hanchett Entry Systems, Inc. is prohibited.

US hesinnovations.com | 800 626 7590 | customerservice.hes@assaabloy.com Canada assaabloydss.ca | 800 461 3007 | sales.dss.ca@assaabloy.com

Electric Strikes

DimensionsSpecifications Certifications

• ANSI/BHMA A156.31, Grade 1

• UL 1034 burglary-resistant listed and suitable for outdoor use

• UL 294 listed

• UL 305 listed

• RoHS compliant

• ANSI/SDI A250.13 windstorm resistant

• Florida Building Code approved

TAS 201, 202, 203

• ANSI-ASTM E330

Frame Application

• Metal

• Wood

Electrical (DC Continuous Duty)

• Dual voltage 12/24 VDC

• 450 mA at 12 VDC/250 mA at 24 VDC

How to Order

SERIES FINISH OPTION (S)

9600 – 630 – LBM

9600 Surface-Mounted Electric Strike for

3/4" Pullman Rim Exit Devices, non-fire rated; no faceplates required

605 Bright Brass LBM Latchbolt Monitor 606 Satin Brass LBSM Latchbolt Strike Monitor 612 Satin Bronze 613 Bronze Toned 613E Dark Oxidized Satin Bronze Powder 629 Bright Stainless Steel 630 Satin Stainless Steel BSP Black Suede Powder

NOTE: Electric strike compatibility is determined at time of electric strike product release. ASSA ABLOY is not responsible for incompatibility of products that have changed in design or craftsmanship by their respective manufacturers. When compatibility is a concern, contact Customer Support for application assistance.

9600 Surface Mounted Electric Strike

9" [228.6mm]

1-3/4" [44.5mm]

3/4" [19mm] iCLASS®

INSTALLATION GUIDE

instalación installation instalação installation installazione

安装 取り付け

설치

УСТАНОВКА

RK40

RWK400

RPK40

13.56 MHz Contactless Smart Card Readers with Keypad

6404-901 A.3 iCLASS RK40, RWK400, RPK40

INSTALLATION GUIDE2 ©2009 HID Global Corporation. All rights reserved.

6404-901 A.3

Parts List componentes pièces peças

Komponenten componenti

部件列表 部品 부품

КОМПЛЕКТАЦИЯ

PARTS

Recommended

LiSTA de comPonenTeS

Recomendado:

LiSTe deS PièceS

Recommandés

PeçAS

Recomendado

komPonenTen

Nr. 6-32 x 0,375 Zoll

eLenco PARTi

Consigliati

部件列表

• 1 - iCLASS 读卡机

• 1 – 安装手册

• 2 - 3.5 mm x .6 螺距 x 12 mm Phillips 机制螺钉

• 3 - #6-32 x .375” Phillips 自攻 (mv) 机制螺钉

• 2 - #6 x 1.5” Phillips 小螺钉

• 1 - #6 x .375” 扳手安全螺钉，防撬

• 2 - 终端读卡机的终端接头

• 1 - 安装垫片

• 1 - 底板

推荐

• 最多 9 个接线头（绞编）

• 电缆，5-9 导线（Wiegand 或 RS232），22 或 24 AWG

[65 mm 或 51 mm] （绞编）

• 线性直流电源

• 金属或塑料接线盒

• 安全工具（用于防撬螺钉）HID 04-0001-03

部品リスト

• 1 - iCLASSリーダー

• 1 - 取り付けマニュアル

• 2 - 3.5 mm x .6 ピッチ x 12 mm プラス小ねじ

• 3 - #6-32 x .375” セルフ タッピング(mv）プラス小ねじ

• 2 - #6 x 1.5” 板金プラスねじ

• 1 - #6 x .375” スパナ用セキュリ ティねじ、不正開封防止

• 2 - ターミナル リーダ用ターミナル コネクタ

• 1 - 取り付けガスケット

• 1 - ベースプレート

推奨

• 最大 9 のワイヤスプライス（ピグテール）

• ケーブル、5～9芯(Wiegandまたは RS232)、22または24 AWG

[65 mmまたは51 mm] (ピグテール)

• リニア DC 電源

• 金属製またはプラスチック製接続 ボックス

• セキュリティツール（不正開封 防止ねじ用）HID 04-0001-03

부품

• 1 - 설치 개스킷

• 1 - 베이스 플레이트

권장 사항

22 또는 24 AWG[65 mm 또는 51 mm] (Pigtail)

Комплектация

шлицем

Рекомендуется:

коробка

• Спецключ (для защитного винта) HID 04-0001-03

INSTALLATION GUIDE 3©2009 HID Global Corporation. All rights reserved.

6404-901 A.3 RK40, RWK400, RPK40 iCLASS

PRODUCT

PRODUCTO

PRODUIT

PRODUTO

PRODUKT

PRODOTTO

製品

产品

제품

ИЗДЕЛИЕ

BASE PART NUMBER

NÚMERO DE COMPONENTE BASE

RÉFÉRENCE DE BASE

NÚMERO DAS PEÇAS BÁSICAS

HAUPTTEILENUMMER

NUMERO PARTE DI BASE

基本部品番号

基本部件编号

기본부품 번호

БАЗОВЫЙ НОМЕР ИЗДЕЛИЯ

INPUT VOLTAGE (VDC)

TENSIÓN DE ENTRADA (VCC)

TENSION D’ALIMENTATION (Vcc)

VOLTAGEM DE ENTRADA (VCC)

EINGANGSSPANNUNG (VDC)

TENSIONE IN INGRESSO (V c.c.)

入力電圧(VDC)

输入电压 (VDC)

입력 전압(VDC)

НАПРЯЖЕНИЕ ПИТАНИЯ

(В постоянного тока)

CURRENT

CORRIENTE

COURANT

CORRENTE

STROMSTÄRKE

CORRENTE

電流

电流

전류

ТОК

OPERATING TEMPERATURE

TEMPERATURA DE FUNCIONAMIENTO

TEMPÉRATURE DE FONCTIONNEMENT

TEMPERATURA OPERACIONAL

BETRIEBSTEMPERATUR

TEMPERATURA D’ESERCIZIO

稼動温度

操作温度

작동 온도

РАБОЧАЯ ТЕМПЕРАТУРА

CABLE LENGTH

LONG. DE CABLE

LONGUEUR DE CÂBLE

COMPRIMENTO DO CABO

COMPRIMENTO DO CABO

LUNGHEZZA CAVO

ケーブル長

电缆长度

케이블 길이

ДЛИНА КАБЕЛЯ

UL REF NUMBER

NÚMERO DE REFERENCIA UL

RÉF. UL

NÚMERO DE REFERÊNCIA UL

UL-REFERENZNUMMER

NUMERO DI RIFERIMENTO UL

UL参照番号

UL 参考编号

UL 참조 번호

Справочный номер в UL

NSC PEAK

RK40

5-16 VDC

75 mA 120 mA

RK40Cx1x2N

RWK400 6131 ** 104 mA 153 mA RWK400Cx1x3N

RPK40 6136 ** / 6133 / 6134 * 120 mA 145 mA RPK40Cx1x4N

不包括接线盒。 接続ボックスは含まれていません。 연결 박스는 제품에 포함되지 않습니다.

Соединительная коробка не прилагается

Specifications

Mounting1 especificaciones spécifications especificações spezifiKationen specifiche

仕様 规格

사양 ХАрАКТЕрИсТИКИ montaje montage montagem montage montaggio

取り付け 安装 설치 КрЕПЛЕнИЕ

* Prox modules - HID Prox: 16 mA less.

** UL listed.

Note: Cable length over 200 feet…