09_l Archl DWGs 12of12sp.pdf

PARTITION AS SCHED CONTINUE GYP

BD TO STRUCT IF REQD.

CEILING AS SCHED, RE: RCP.

3/ 4"

PLASTIC LAMINATE AS SCHED ON ALL

EXPOSED SURFACES.

WOOD BLOCKING.

CASEWORK AS SCHED, RE: ELEVATIONS.

SEALANT

U N

O

4"

1/2"

1"

1/

2" 1/

8"

SEAMLESS ROLLED EDGE TO

BACKSPLASH

1/16" THK TYPE 304 STAINLESS STEEL, SATIN FINISH

COUNTERTOP AND BACKSPLASH, RE: SPECS REINFORCE

UNDERSIDE WITH CHANNELS OR THICKER SHEET METAL

AS

REQD TO INSURE RIGIDITY WITHOUT DEFLECTION.

ADD BLOCKING OR

CHANNELS AS REQD

SOLID WOOD STOCK

BLOCKING, TYP.

REFER TO BASE CABINET

SECTION FOR DETAILS.

FOR LOCATIONS WITHOUT A BACKSPLASH,

TERMINATE COUNTERTOP FLUSH WITH

WALL. SEAL BETWEEN COUNTERTOP AND

WALL.

1/ 2"

V A

R

IE

S R

E : E

LE

V

1"

3/ 4"

1"

UPPER CABINET AS SCHED.

1/2" THK HOMOSOTE WITH FABRIC ON

FRONT, WRAP AROUND EDGES AND SECURE

IN BACK. RE: INTERIOR FINISHES FOR SCHED

FABRIC AND DIRECTION.

PROVIDE CUTOUT AT ALL OUTLETS AND

DEVICES, CUTOUT SHALL BE 1" CLEAR EACH

SIDE OF OUTLET COVER OR DEVICE COVER.

WRAP AND SECURE FABRIC IN BACK.

CONCEALED METAL Z-CLIPS.

COUNTERTOP AS SCHED.

NOTES:

1. ALIGN VERTICAL PANEL JOINTS WITH CABINET JOINTS WHEN POSSIBLE,

SUBMIT JOINT LAYOUT FOR APPROVAL PRIOR TO FABRICATION.

2. PANELS SHALL TERMINATE 1'-0" FROM EDGE OF SINKS, VERIFY WITH ARCH

IF PANELS SHOWN BEHIND SINK.

V A

R

IE

S

PARTITION AS SCHED CONTINUE GYP

BD TO STRUCT IF REQD.

CEILING AS SCHED, RE: RCP.

INSTALL UPPER VALENCE ONLY WHERE

LIGHTS ARE INSTALLED ON CABINET TOP,

RE: ELEC WHEN PROVIDED, CONTINUE

VALENCE FOR ENTIRE LENGTH OF UPPER

CABINETS AND AT EXPOSED ENDS, UNO.

CASEWORK AS SCHED, RE: ELEVATIONS.

PLASTIC LAMINATE AS SCHED ON ALL

EXPOSED SURFACES.

2"

1/

2"

1/

2" 1/

8"

U N

O

4"

1/2" SOLID SURFACING

OR 3/4" STONE AS

SCHED, W/ EASED

EDGES.

TRANSACTION

COUNTER

SEALANT

FOR LOCATIONS WITHOUT A BACKSPLASH,

TERMINATE COUNTERTOP FLUSH WITH WALL.

SEALANT BETWEEN COUNTERTOP AND WALL.

EASED COUNTER,

TYP.

SEALANT OR CONT.

WELD.

1/2" SOLID SURFACING OR

3/4" STONE AS SCHED, APRON

AND COUNTERTOP TO BE ONE

PIECE.

SOLID WOOD STOCK

BLOCKING, TYP.

REFER TO BASE CABINET

SECTION FOR DETAILS.

1/2"

DRAWER EDGE DETAIL.

DRAWER

ISOMETRIC.

FOR 15" WIDE UNITS:

- DIMENSION "A" SHALL BE 12" CLEAR.

- DRAWER SHALL BE DESIGNED TO HOLD LETTER SIZE

HANGING FOLDER WITH TABS (SMEAD C13H OR

EQUAL).

- ALLOW 1" CLEAR ABOVE TOP OF DRAWER EDGE.

FOR 18" WIDE UNITS:

- DIMENSION "A" SHALL BE 15" CLEAR.

- DRAWER SHALL BE DESIGNED TO HOLD LEGAL SIZE

HANGING FOLDER WITH TABS (SMEAD C23H OR EQUAL).

- ALLOW 1" CLEAR ABOVE TOP OF DRAWER EDGE.

FOR OTHER UNIT WIDTHS:

- DIMENSION "A" SHALL BE 3" LESS UNIT WIDTH.

- DRAWER EDGE SHALL BE CONSTRUCTED AS

DETAILED.

- ALLOW 1 1/2" CLEAR ABOVE TOP OF DRAWER EDGE.

3/16"

1/ 2"

1/

2"

A

PLAM TOP AND SIDES TO MATCH FRONT.1' - 6"

3/

4"

. AS NOTED IN CABINET SECT.

DOOR/DRAWER PULLS AS SCHED, TYP.

DRAWER SLIDES TO SUPPORT 150 LBS.

1/ 4"

V A

R

IE

S

PARTITION AS SCHED CONTINUE GYP BD

TO STRUCT IF REQD.

CEILING AS SCHED, EXTEND TO

PARTITION, RE: RCP.

PLASTIC LAMINATE ON 3/4" PLYWD

PROVIDE MATCHING PANEL AT

EXPOSED ENDS, ALIGN WITH DOOR

FACE.

CONTINUE GYP BD AS SCHED AND

CEILING BEHIND PANEL.

CASEWORK AS SCHED, RE: ELEVATIONS.

1/8" MAX GAP BETWEEN CEILING AND

PANEL.

NOTE: WHERE LAMINATE JOINTS ARE

REQUIRED, ALIGN JOINTS WITH EDGE OF

CABINET UNITS.

1/2"

1/

2" 1/

8"

U N

O

4"

*NOTES:

1. ALL COUNTERTOPS WITH SINKS SHOULD HAVE A SPILL-PROOF EDGE.

2. WHERE COUNTERTOP CHANGES DIRECTIONS, MITER JOINT SO SPILL

PROOF EDGE IS ALWAYS AT THE EDGE.

3. IF A SPILL PROOF EDGE IS SHOWN TO BUTT WITH A STANDARD EDGE,

VERIFY WITH ARCH IF BOTH COUNTERS ARE INTENDED TO HAVE SPILL

PROOF EDGE.

SEALANT

PLASTIC LAMINATE AS SCHED.

FOR LOCATIONS WITHOUT A BACKSPLASH,

TERMINATE COUNTERTOP FLUSH WITH

WALL. SEAL BETWEEN COUNTERTOP AND

WALL.

3/4" RADIUS AT BACKSPLASH,

SIDES TO BE STRAIGHT.

SPILL PROOF EDGE, 1/8"

HIGH.

HARDWOOD EDGE, TYP.

3/4" PLYWD TYP, UNO.

SOLID WOOD STOCK

BLOCKING, TYP.

REFER TO BASE CABINET

SECTION FOR DETAILS.

SUPPORT @ COUNTER ABOVE 30".

MAX

7"

COUNTERTOP AND APRON AS SCHED.

ATTACH SUPPORT TO CONCEALED

CONTINUOUS BLOCKING IN PARTITION @ 48"

O.C.

KNEE SPACES BETWEEN SUPPORTS

SHALL BE EQUAL UNO.

COUNTERTOP ASSEMBLY SHALL

SUPPORT 300# MIN.

R E

F E

LE

V

SURFACE MOUNTED COUNTER

SUPPORT BY MANUFACTURER

2"

2"

DOOR EDGE

TYP CABINET

DOOR

PULL AS SPECIFIED

(06 41 16)

DRAWER

EDGE

PULL AS SPECIFIED

(06 41 16)

2"

TYP DRAWER FRONT

EQ EQ

0"2" 0" 2"

UNO

1' - 6"

1/ 2"

V A

R

IE

S 3"

7' -2

A

F F

PARTITION AS SCHED

3 5/8" MTL STUD FRAME AND

BRACING.

CEILING AS SCHED, RE: RCP.

5/8" GYP BD ON 3 5/8" MTL STUDS

REFER TP RCP FOR LENGTH OF

SOFFIT.

CASEWORK AS SCHED, RE: ELEVATIONS.

CONTINUE GYP BD TO STRUCT IF REQD.

1/

2"

1/ 8"

1/

2"

1/2"

U N

O

4"

PLASTIC LAMINATE ON 3/4"

PLYWD W/ HARDWOOD

EDGES.

TRANSACTION

COUNTER

SEALANT

PLASTIC LAMINATE AS SCHED.

FOR LOCATIONS WITHOUT A BACKSPLASH,

TERMINATE COUNTERTOP FLUSH WITH

ALL.

SEAL BETWEEN COUNTERTOP AND WALL.

3/4" RADIUS AT

BACKSPLASH, SIDES TO BE

STRAIGHT.

HARDWOOD EDGE,

TYP.

3/4" PLYWD TYP, UNO.

SOLID WOOD STOCK

BLOCKING, TYP.

REFER TO BASE CABINET

SECTION FOR DETAILS.

WALL PARTITION

SEAL END OF PANEL TO WALL

CABINET BACK (OMIT @ SIM)

CABINET END PANEL

PLAM EXPOSED SURFACE

CABINET END PANEL

PLAM EXPOSED SURFACE

CABINET FACE

1/16"

CABINET SIDE

CABINET FACE

ADJACENT

CABINET

1/

2"

WALL PARTITION

GROMMET

COUNTERTOP

SPLASH, IF

SPECIFIED

3/ 4"

3"3" MAX 1" MIN

WALL PARTITION

CABINET FACE

FILLER PANEL

CABINET SIDE

GYP BOARD FURRDOWN

SEE INTERIOR DETAILS

CABINET HEAD

WALL BLOCKING

CABINET BACK

WALL PARTITION

0' - 0 1/2"

CABINET BOTTOM

WALL PARTITION

CABINET BACK (OMIT AT SIM)

CABINET SIDE BEYOND

COUNTER TOP

SEAL COUNTERTOP TO WALL

3"

CABINET BACK

WALL PARTITION

DRAWER BACK

BRAWER BOTTOM

1/ 8"

DRAWER FACE

DRAWER BOTTOM (OMNIT @

SIM)

DRAWER OR DOOR STOP

CABINET DOOR OR DRAWER

2" 1/

8"

CABINET DOOR (OMIT AT SIM)

CABINET BOTTOM

GENERAL CASEWORK NOTES

1. ALL CASEWORK SHOWN ON THIS SHEET IS PLASTIC LAMINATE CLAD UNO.

2. ALL EXPOSED SURFACES AND EDGES SHALL RECEIVE PLASTIC LAMINATE AS SCHED.

ALL INTERIOR SURFACES AND EDGES SHALL RECEIVE WHITE MELAMINE UNO, TYP.

4. CABINET WIDTHS ARE BASED ON MODULE INCREMENTS OF 3 INCHES FROM 12 TO 36

INCHES WIDE CABINETS AND 6 INCH INCREMENTS FOR 36 TO 48 INCHES OF WIDE

CABINETS.

5. ALL COUNTERTOPS SHALL BE PLASTIC LAMINATE UNO. PROVIDE 3/4" PLYWD

SUBSTRATE FOR ALL WET LOCATIONS. 3/4" MDF AT OTHER LOCATIONS, UNO.

6. REFER TO 83-A-711 THROUGH 83-A-15 FOR MILLWORK DETAILS.

7. REFER TO 83-A-701 FOR SOFFIT/FURR DOWN DETAILS.

8. REFER TO SHEET 83-A-702 THROUGH 83-A-705 FOR TYP CASEWORK DETAILS.

9. INSTALL 3/4" THK BACKSPLASHES AT ALL LOCATIONS UNO. INSTALL 3/4" END

SPLASHES WHEN COUNTER IS ADJACENT TO A PARTITION OR TALLER CASEWORK.

LAMINATE ALL EXPOSED EDGES TO MATCH COUNTERTOP. BACKSPLASH AND END

SPLASH TO BE 4" HIGH UNO.

10. RADIUS ALL OUTSIDE CORNERS OF COUNTERTOPS 1", UNO. DO NOT RADIUS CORNER

IF A FULL HEIGHT REFRIGERATOR IS PLANNED IMMEDIATELY NEXT TO

COUNTERTOP.

11. ADJACENT UPPER CABINETS SHALL HAVE FLUSH BOTTOM TO FORM CONTINUOUS

POCKET BEHIND FRONT VALENCE FOR LIGHT FIXTURES. BOTTOM OF EXPOSED SIDES

SHALL ALIGN WITH FRONT.

12. PROVIDE FILLER PANEL WHERE CASEWORK ABUTS WALL OR HEADER ABOVE, 1 INCH

MINIMUM TO 3 INCH MAXIMUM WIDTH. UNO.

13. PROVIDE FINISHED END PANELS AND/OR END RETURNS AT OPEN ENDED, EXPOSED

CASEWORK OR AT KNEE SPACES.

14. LOCATE GROMMETS 48 INCHES ON CENTER MAX. AT BACK OF COUNTERTOPS ABOVE

KNEE SPACE, ONE GROMMET MIN. PER COUNTERTOP RUN. COORDINATE EXACT

LOCATION WITH OWNER PRIOR TO INSTALLATION. SHOW GROMMET LOCATIONS ON

SHOP DRAWINGS.

16. FIELD VERIFY ALL DIMENSIONS PRIOR TO FABRICATION OF CASEWORK.

17. SOME DETAILS ON THIS SHEET MAY NOT BE USED.

18. PROVIDE FIRE TREATED WOOD BLOCKING WITHIN WALL FOR ALL MOUNTED

CASEWORK.

2' - 6"

2'

0"

ELEVATION PLAN

CASEWORK ELEVATION TYPE

NOMINAL HEIGHT IN INCHES

NOMINAL WIDTH IN INCHES

DESCRIPTION NOMENCLATURE

1 DWR 2DR 1SH 1 DRAWER OVER 2 DOORS W/ 1 SHELF

1PEN, 4DWR EQ 1 PENCIL DRAWER OVER

4 DRAWERS EQUAL SIZE

3OPEN 3 OPEN SPACES

ABBREVIATIONS

BLNK BLANK

CATH CATHETERIZATION

CSWK CASEWORK

CNTR COUNTER

DR DOOR

DWR DRAWER

EQ EQUAL

EQUIP EQUIPMENT

HD HEAVY DUTY

KNEE KNEE SPACE

LCKR LOCKER

OPEN OPEN SPACE(S)

PEN PENCIL DRAWER

REF REFRIGERATOR

SH SHELF OR SHELVES

STOR STORAGE

CASEWORK

TAG

BK

BK

CASEWORK LEGEND

D A

T E

ST

A

M P

Drawing Title

Approved Project Director:

Project Title

Date

Location

Checked

Building Number

Project Number

Drawing Number

Drawn

PSP 309070 Revisions Date

ARCHITECT/ENGINEERS: Office of

Construction and Facilities

Management o n e e ig h th in c h o n e fo o t 1 th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t

VA FORM 08-6231

1 2 3 4 5 6 87 9

F

E

D

C

B

A

97 8654321

FILE NAME

Project Abbreviation

F

E

D

C

B

A

F

IL

E N

A M

E

Page Southerland Page, LLP.

1800 Main Street Suite 123

Dallas, TX 75201 pagethink.com

TEL

FAX

ARCHITECTURE / ENGINEERING / INTERIORS / CONSULTING

Austin / Dallas / Denver / Houston / Washington DC /

International Affiliate Offices

214 522 3900

214 522 4380

DWG

W

R e v it

L o ca l\ b A

-S C I_

In te ri o r-

-C

E N

T R A L c ry st a lm cm .r v t

/1

/2

:0 :2

P

M

W:\@RevitLocal\309070b3A-SCI_Interior-2018-CENTRAL_crystalmcm.rvt

83-A-701

CONSTRUCTION

VA-LTSCIF-D

TEAM

549-820B

TAB

ARCHITECTURAL - CASEWORK STANDARDS

LONG TERM SPINAL CORD INJURY

VA NORTH TEXAS HEALTH CARE SYSTEM

4500 S. LANCASTER RD. DALLAS, TX 75216OFFICE OF CONSTRUCTION AND FACILITIES

MANAGEMENT DIRECTOR, CENTRAL REGION

06 MAY 2021

FULLY SPRINKLEREDBID PACKAGE B

SCALE: 1" = 1'-0"D1 SOFFIT DETAIL

SCALE: 6" = 1'-0"F2 COUNTERTOP DETAIL

SCALE: 1" = 1'-0"E4 TACKABLE SURFACE DETAIL

SCALE: 1" = 1'-0"D2 SOFFIT DETAIL

SCALE: 6" = 1'-0"F6 COUNTERTOP DETAIL

SCALE: 1" = 1'-0"E2 FILE DRAWER DETAILS

SCALE: 1" = 1'-0"E7 WRITING SURFACE DRAWER

SCALE: 1" = 1'-0"D4 SOFFIT DETAIL

SCALE: 6" = 1'-0"F4 COUNTERTOP DETAIL

SCALE: 1" = 1'-0"F1 TYPICAL COUNTER SUPPORT

SCALE: 6" = 1'-0"E6 TYPICAL PULL LOCATIONS

SCALE: 1" = 1'-0"D6 TYPICAL SOFFIT DETAIL

SCALE: 6" = 1'-0"F7 TYPICAL COUNTERTOP DETAIL

SCALE: 6" = 1'-0"A5

PLAN - CABINET

@ BACK WALL

SCALE: 6" = 1'-0"A2

PLAN - CABINET

CORNER

SCALE: 6" = 1'-0"A3

PLAN - CABINET

TO CABINET

SCALE: 6" = 1'-0"A1

PLAN - COUNTER

@ GROMMET

SCALE: 6" = 1'-0"A4

PLAN - FILLER @

SIDE WALL

SCALE: 6" = 1'-0"D7 SECT - CABINET @ WALL

SCALE: 6" = 1'-0"B7

SECT - COUNTER

@ WALL

SCALE: 6" = 1'-0"A8

SECT - DRAWER

BACK TO WALL

SCALE: 6" = 1'-0"A7

SECT - DRAWER FACE

TO DOOR

SCALE: 6" = 1'-0"A6

SECTION -

CABINET @ PULL

A T

T S

XETE FO

S A

M

LAB

1 0 9 0 0

R E G

IS

TE

RED ARCH

ITE

C T

A

I F

A

T T

AI

O N

I II

05/06/21

BASE CABINET WITHOUT

DRAWERS.

CONCEALED HINGES, TYP.

DOOR PULLS, TYP.

ADJUSTABLE SHELF.

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

4"

R E

: E

LE

V A

T

IO

N S

2'

U N

O

3"

RE: PLAN

2' - 0" TYP

TYP

1' - 9 1/2"

BC BD

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

CONCEALED HINGES,

TYP.

DOOR PULLS, TYP.

ADJUSTABLE SHELF.

BASE AS SCHED.

BLOCKING, TYP.

BASE CABINET WITHOUT DRAWERS.

4"

3"

RE: PLAN

2' - 0" TYP

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

TYP

1' - 9 1/2"

BE BF

LAMINATE ALL EXPOSED SURFACES

TO MATCH CASEWORK FRONTS.

ADJUSTABLE SHELVES.

BASE CABINET WITH

OPEN SHELVES.

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

4"

R E

: E

LE

V A

T

IO

N S

2'

U N

O

3"

RE: PLAN

2' - 0" TYP

TYP

1' - 9 1/2"

BQ

BASE UNIT WITH

PULL-OUT DRAWER.

BLOCKING, TYP.

BASE AS SCHED.

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

HEAVY-DUTY SHELF,

TOP OF SHELF TO ALIGN WITH

ADJACENT DRAWERS WHERE

NOTED.

100# HEAVY DUTY FULL EXTENSION

DRAWER SLIDES, SIDE MOUNT.

DOOR/DRAWER PULLS AS

SCHED, TYP.

4"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

RE: PLAN

2' - 0" TYP

3"

1/

4"

1'

/4

BS BT

C

LE

A R

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

ADJUSTABLE SHELVES.

BASE CABINET WITH PENCIL

DRAWER AND OPEN

SHELVES.

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

RE: PLAN

2' - 0" TYP

3"

R E

: E

LE

V A

T

IO

N S

2'

U N

O

4"

2"

TYP

1' - 9 1/2"

R E

: E

LE

V

4" U

N O

2"

BU

BASE CABINET WITH PENCIL

DRAWER

AND OPEN SHELVES.

BASE AS SCHED.

BLOCKING, TYP.

LAMINATE FOR ALL EXPOSED SURFACES

TO MATCH CASEWORK FRONTS.

ADJUSTABLE SHELF.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

R E

: E

LE

V

4" U

N O

3"

RE: PLAN

2' - 0" TYP

4"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

TYP

1' - 9 1/2"

2"

BV

CONCEALED HINGES, TYP.

1/8" REVEAL.

DOOR/DRAWER PULLS, TYP.

ADJUSTABLE SHELF.

SURFACE MOUNT CUP DISPENSER

TO DOOR, REFER TO ACCESSORY

SCHED.

BASE CABINET WITHOUT

DRAWERS DESIGN FOR CUP

DISPENSER.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

BLOCKING, TYP.

BASE AS SCHED.

4"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

3"

RE: PLAN

2' - 0" TYP

R E

: E

LE

V

4" U

N O

5"

± 1' - 4" 6"

CC

T

O P

3"

BASE UNIT WITH

FILM SLOTS.

BLOCKING, TYP.

BASE AS SCHED.

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

1/4" PLAM CLAD VERTICAL PLWD.

SPACED EQUALLY TO CREATE SLOTS 3

1/2" TO

4 1/2" WIDE.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

4"

R E

: E

LE

V A

T

IO

N S

2'

U N

O

RE: PLAN

2' - 0" TYP

3"

1/

2"

CF

1'

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

VERTICAL SUPPORT

BETWEEN DRAWERS.

BASE UNIT WITH FILM

SLOTS AND DRAWER.

BLOCKING, TYP.

BASE AS SCHED.

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

1/4" PLAM CLAD VERTICAL PLWD SPACED

EQUALLY TO CREATE SLOTS 31/2" TO

4 1/2" WIDE.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

RE: PLAN

2' - 0" TYP

3"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

4" 8"

2"

3/

4"

CG

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

CONTINUOUS HINGE, TYP.

1/16" MAX REVEAL TO MATCH

ADJACENT CASEWORK, TYP.

BASE CABINET WITH

LAUNDRY HAMPER.

PULL OPEN CABINET WITH

CONTINUOUS HINGE AT BASE.

DOOR PULL, TYP.

SIDE PANELS ON BOTH SIDES, TYP.

HINGE.

NOTE: HAMPER

UNIT SHALL BE

WEIGHTED TO

CLOSE

AUTOMATICALLY.

EDGE OF

SIDE

PANEL.

RUBBER

STOPS.

RUBBER STOP.

REMOVABLE PANEL

ON BOTH SIDES.

4"

R E

: E

LE

V A

T

IO

N S

3"

RE: PLAN

2' - 0" TYP

TYP

1' - 9"

1'-3" MAX

R E

: E

LE

V

1'

CL

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

BASE CABINET CPU &

EQPM STORAGE.

LAMINATE ALL EXPOSED SURFACES

TOMATCH CASEWORK FRONTS.

GROMMET IN SIDE WHEN ADJACENT

TO OPEN KNEE SPACE, FOR CPU

ONLY.

WHEN OUTLETS ARE LOCATED BEHIND

UNIT, FACE PLATE SHALL BE INSTALLED

ON BACK SURFACE.

BASE AS SCHED.

BLOCKING, TYP.

4"

R E

: E

LE

V A

T

IO

N S

3"

RE: PLAN

2' - 0" TYP

CP

SPACE BELOW COUNTER

FOR EQUIPMENT.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

RE: PLAN

2' - 0" TYP

R E

: E

LE

V A

T

IO

N S

CR

TRASH GROMMET CENTER IN COUNTERTOP OF UNIT.

BASE CABINET WITH

TRASH GROMMET.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

INSIDE CABINET SEAL ALL JOINTS ON

BOTTOM AND SIDES.

FINISHED END PANEL ON CSWK BEYOND.

CABINET DOOR WITH TOE SPACE

CONNECTED TO DOOR.

BASE AS SCHED.

INSTALL ON SIDES

AND BACK.

FLOOR AS SCHED.

FIXED SINK FRONT.

RE: PLAN

2' - 0" TYP

3"

R E

: E

LE

V A

T

IO

N S

4"

R E

: E

LE

V

CT

BASE CABINET

WITH OPEN TOP

PANEL.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

BASE AS SCHED INSTALL ON SIDES

AND BACK.

FLOOR AS SCHED.

5/8" DIA FLEXIBLE

BLACK RUBBER

SEAL.

DOOR FRONT ELEVATION.

OPEN TOE

SPACE FOR

FOOT PEDAL

ACCESS.

OPEN FRONT.

ADJUSTABLE REAR

PANEL RE:

ELEVATION ABOVE.

CONCEALED HINGES & MAGNETIC LATCH.

CABINET PULL, TYP

5/16" DIA HOLES AT 1" O.C.

FINISHED END PANEL ON CSWK BEYOND.

ADJUSTABLE PANEL ELEVATION.

3" BARREL

BOLT, STANLEY

#225020 ON

REAR OF

PANEL.

4" DIA HOLE FOR

ACCESS TO BOLT.

1/ 2"

1/

2" 4"

8" 4"

R E

: E

LE

V A

T

IO

N S

4"

9"

4"

1/ 2"

8"

RE: PLAN

2' - 0" TYP

CU

ADA REQUIREMENTS FOR BENCH:

- SIZE MUST BE 48"W x 24"D MIN.

- BENCH TO SUPPORT 300#.

- WATER SHALL NOT ACCUMULATE ON

SURFACE IN WET LOCATIONS.

BENCH FOR

DRESSING ROOMS.

BLOCKING, TYP.

BASE AS SCHED.

IF LOCATED IN A ROOM WITH A SHOWER

OR TUB, FABRICATE TO MEET

REQUIREMENTS FOR A WET LOCATION.

TOP TO HAVE A SLIP RESISTANT

SURFACE.

COUNTERTOP AS SPECIFIED, REF TO 83-

A-701 AND ELEVATIONS, NO BACKSPLASH.

1 1/2" BULLNOSE EDGE, TYP.

LAMINATE ALL EXPOSED SURFACES

TO MATCH CASEWORK FRONTS.

2 LAYERS OF 3/4" PLWD

ON ENDS.

RE: PLAN

2' - 0" TYP

1' - 0" 6"

1'

U N

O

4"

1/

2"

CX

BENCH TO SUPPORT MIN 300# PER 48 LINEAR INCHES.

JOIN UNITS WHEN ARRANGED BACK TO BACK.

SECURE UNIT TO FLOOR/WALL TO PREVENT ANY

MOVEMENT.

BASE AS SCHED.

ONE-SIDE ACCESS BENCH FOR

DRESSING ROOMS

W/LOCKERS.

(NON-ADA)

BLOCKING, TYP.

LOCKERS AS SCHED, RE: ACCESSORIES.

SEALANT.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS, NO BACKSPLASH.

1 1/2" BULLNOSE EDGE, TYP.

LAMINATE ALL EXPOSED

SURFACES TO MATCH CSWK

FRONTS.

2 LAYERS OF 3/4" PLWD ON ENDS.

1' - 3"

1/

2"

1'

U N

O

4"

RE: PLAN

2' - 9" TYP

3" 3/4"

CY

BASE CABINET WITH

PENCIL DRAWER.

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

CONCEALED HINGES, TYP.

DOOR/DRAWER PULLS, TYP.

ADJUSTABLE

SHELF.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

RE: PLAN

2' - 0" TYP

3"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

4"

TYP

1' - 9 1/2"

2"

R E

: E

LE

V

4" U

N O

BK BLBJ

GENERAL CASEWORK NOTES

1. ALL CASEWORK SHOWN ON THIS SHEET IS PLASTIC LAMINATE CLAD UNO.

2. ALL EXPOSED SURFACES AND EDGES SHALL RECEIVE PLASTIC LAMINATE AS SCHED.

ALL INTERIOR SURFACES AND EDGES SHALL RECEIVE WHITE MELAMINE UNO, TYP.

4. CABINET WIDTHS ARE BASED ON MODULE INCREMENTS OF 3 INCHES FROM 12 TO 36

INCHES WIDE CABINETS AND 6 INCH INCREMENTS FOR 36 TO 48 INCHES OF WIDE

CABINETS.

5. ALL COUNTERTOPS SHALL BE PLASTIC LAMINATE UNO. PROVIDE 3/4" PLYWD

SUBSTRATE FOR ALL WET LOCATIONS. 3/4" MDF AT OTHER LOCATIONS, UNO.

6. REFER TO 83-A-711 THROUGH 83-A-15 FOR MILLWORK DETAILS.

7. REFER TO 83-A-701 FOR SOFFIT/FURR DOWN DETAILS.

8. REFER TO SHEET 83-A-702 THROUGH 83-A-705 FOR TYP CASEWORK DETAILS.

9. INSTALL 3/4" THK BACKSPLASHES AT ALL LOCATIONS UNO. INSTALL 3/4" END

SPLASHES WHEN COUNTER IS ADJACENT TO A PARTITION OR TALLER CASEWORK.

LAMINATE ALL EXPOSED EDGES TO MATCH COUNTERTOP. BACKSPLASH AND END

SPLASH TO BE 4" HIGH UNO.

10. RADIUS ALL OUTSIDE CORNERS OF COUNTERTOPS 1", UNO. DO NOT RADIUS CORNER

IF A FULL HEIGHT REFRIGERATOR IS PLANNED IMMEDIATELY NEXT TO

COUNTERTOP.

11. ADJACENT UPPER CABINETS SHALL HAVE FLUSH BOTTOM TO FORM CONTINUOUS

POCKET BEHIND FRONT VALENCE FOR LIGHT FIXTURES. BOTTOM OF EXPOSED SIDES

SHALL ALIGN WITH FRONT.

12. PROVIDE FILLER PANEL WHERE CASEWORK ABUTS WALL OR HEADER ABOVE, 1 INCH

MINIMUM TO 3 INCH MAXIMUM WIDTH. UNO.

13. PROVIDE FINISHED END PANELS AND/OR END RETURNS AT OPEN ENDED, EXPOSED

CASEWORK OR AT KNEE SPACES.

14. LOCATE GROMMETS 48 INCHES ON CENTER MAX. AT BACK OF COUNTERTOPS ABOVE

KNEE SPACE, ONE GROMMET MIN. PER COUNTERTOP RUN. COORDINATE EXACT

LOCATION WITH OWNER PRIOR TO INSTALLATION. SHOW GROMMET LOCATIONS ON

SHOP DRAWINGS.

16. FIELD VERIFY ALL DIMENSIONS PRIOR TO FABRICATION OF CASEWORK.

17. SOME DETAILS ON THIS SHEET MAY NOT BE USED.

18. PROVIDE FIRE TREATED WOOD BLOCKING WITHIN WALL FOR ALL MOUNTED

CASEWORK.

2' - 6"

2'

0"

ELEVATION PLAN

CASEWORK ELEVATION TYPE

NOMINAL HEIGHT IN INCHES

NOMINAL WIDTH IN INCHES

DESCRIPTION NOMENCLATURE

1 DWR 2DR 1SH 1 DRAWER OVER 2 DOORS W/ 1 SHELF

1PEN, 4DWR EQ 1 PENCIL DRAWER OVER

4 DRAWERS EQUAL SIZE

3OPEN 3 OPEN SPACES

ABBREVIATIONS

BLNK BLANK

CATH CATHETERIZATION

CSWK CASEWORK

CNTR COUNTER

DR DOOR

DWR DRAWER

EQ EQUAL

EQUIP EQUIPMENT

HD HEAVY DUTY

KNEE KNEE SPACE

LCKR LOCKER

OPEN OPEN SPACE(S)

PEN PENCIL DRAWER

REF REFRIGERATOR

SH SHELF OR SHELVES

STOR STORAGE

CASEWORK

TAG

BK

BK

CASEWORK LEGEND

BASE CABINET WITH

SLIDING SHELF

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

CONCEALED HINGES, TYP.

DOOR/SLIDING SHELF PULLS,

TYP.

ADJUSTABLE

SHELF.

1/16" MAX GAP BETWEEN

DOOR/SLIDING SHELF FRONTS, TYP.

RE: PLAN

2' - 0" TYP

3"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

4"

TYP

1' - 9 1/2"

BJ

1/

2" SLIDING SHELF-USE FULL EXTENSION

SLIDER 150 LB RATED

BASE CABINET WITH

PENCIL DRAWER.

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

DOOR/DRAWER PULLS, TYP.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

RE: PLAN

2' - 0" TYP

3"

R E

: E

LE

V A

T

IO

N S

2'

0"

U N

O

4"

2"

R E

: E

LE

V

4" U

N O

BI

HEAVY DUTY DRAWER GUIDES

AS SCHED.

D A

M P

Drawing Title

Approved Project Director:

Project Title

Date

Location

Checked

Building Number

Project Number

Drawing Number

Drawn

PSP 309070 Revisions Date

ARCHITECT/ENGINEERS: Office of

Construction and Facilities

Management o n e e ig h th in c h o n e fo o t 1 th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t

VA FORM 08-6231

1 2 3 4 5 6 87 9

F

E

D

C

B

A

97 8654321

FILE NAME

Project Abbreviation

F

E

D

C

B

A

F

IL

E N

A M

E

Page Southerland Page, LLP.

1800 Main Street Suite 123

Dallas, TX 75201 pagethink.com

TEL

FAX

ARCHITECTURE / ENGINEERING / INTERIORS / CONSULTING

Austin / Dallas / Denver / Houston / Washington DC /

International Affiliate Offices

214 522 3900

214 522 4380

DWG

W

R e v it

L o ca l\ b A

-S C I_

In te ri o r-

-C

E N

T R A L c ry st a lm cm .r v t

/1

/2

:0 :3

P

M

W:\@RevitLocal\309070b3A-SCI_Interior-2018-CENTRAL_crystalmcm.rvt

83-A-702

CONSTRUCTION

VA-LTSCIF-D

TEAM

549-820B

TAB

ARCHITECTURAL - CASEWORK STANDARDS

LONG TERM SPINAL CORD INJURY

VA NORTH TEXAS HEALTH CARE SYSTEM

4500 S. LANCASTER RD. DALLAS, TX 75216OFFICE OF CONSTRUCTION AND FACILITIES

MANAGEMENT DIRECTOR, CENTRAL REGION

06 MAY 2021

FULLY SPRINKLEREDBID PACKAGE B

SCALE: 1" = 1'-0"F7 BASE CABINET - BC BD

SCALE: 1" = 1'-0"E7 BASE CABINET - BE BF

SCALE: 1" = 1'-0"E5 BASE CABINET - BQ

SCALE: 1" = 1'-0"C5 BASE CABINET - BS BT

SCALE: 1" = 1'-0"A5 BASE CABINET - BU

SCALE: 1" = 1'-0"F3 BASE CABINET - BV

SCALE: 1" = 1'-0"E3 BASE CABINET - CC

SCALE: 1" = 1'-0"C3 BASE CABINET - CF

SCALE: 1" = 1'-0"A3 BASE CABINET - CG

SCALE: 1" = 1'-0"F2 BASE CABINET - CL

SCALE: 1" = 1'-0"E2 BASE CABINET - CP

SCALE: 1" = 1'-0"C2 BASE CABINET - CR

SCALE: 1" = 1'-0"A2 BASE CABINET - CT

SCALE: 1" = 1'-0"F1 BASE CABINET - CU

SCALE: 1" = 1'-0"E1 BASE CABINET - CX

SCALE: 1" = 1'-0"C1 BASE CABINET - CY

SCALE: 1" = 1'-0"F5 BASE CABINET - BJ BK BL

SCALE: 1" = 1'-0"C7 BASE CABINET-BH

SCALE: 1" = 1'-0"A7 BASE CABINET - BI

A T

T S

XETE FO

S A

M

LAB

1 0 9 0 0

R E G

IS

TE

RED ARCH

ITE

C T

A

I F

A

T T

AI

O N

BASE UNIT WITH 2

FILE DRAWERS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

1/16" MAX GAP BETWEEN DOOR/DRAWER

FRONTS, TYP.

FILE DRAWER, RE:83-A-701 FOR DETAILS.

FILE DRAWER, RE:83-A-701 FOR DETAILS.

RE: PLAN

2' - 0" TYP

3"

M

IN

/4

M

IN

/4

2"

E Q

E Q

4"

R E

: E

LE

V A

T

IO

N S

DB

BASE UNIT WITH 3

EQUAL DRAWERS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

1/

2"

1/ 2"

1/

4"

RE: PLAN

2' - 0" TYP

3"

E Q

E Q

E Q

2"

4"

R E

: E

LE

V A

T

IO

N S

DE

BASE UNIT WITH PENCIL

DRAWER AND 2 EQUAL

FILE DRAWERS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

FILE DRAWER, RE:83-A-701 FOR DETAILS.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

FILE DRAWER, RE:83-A-701 FOR DETAILS.

4"

R E

: E

LE

V A

T

IO

N S

RE: PLAN

2' - 0" TYP

3"

E Q

E Q

4"

M

IN

/4

M

IN

/4

2"

2"

DG

BASE UNIT WITH PENCIL

DRAWER, STORAGE

DRAWER, AND FILE

DRAWER.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

BASE AS SCHED.

BLOCKING, TYP.

DOOR/DRAWER PULLS AS SCHED, TYP.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

FILE DRAWER, RE: 83-A-701 FOR DETAILS.

RE: PLAN

2' - 0" TYP

3"

M

IN

/4

1/

4" 2"

2"

4"

R E

: E

LE

V A

T

IO

N S 8 1/

4" 1'

/4

4"

DH

BASE UNIT WITH

PENCIL DRAWER AND

3 EQUAL DRAWERS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

RE: PLAN

2' - 0" TYP

3"

4"

R E

: E

LE

V A

T

IO

N S

1/

4"

1/ 4"

1/

4" 2"

2"

E Q

E Q

E Q

4"

DM

BASE UNIT WITH PENCIL

DRAWER, 2 EQUAL DRAWERS,

AND FILE DRAWER.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

FILE DRAWER, RE:83-A-701 FOR DETAILS.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

/4

1/

4"

1/ 4"

2"

2"

RE: PLAN

2' - 0" TYP

3"

4"

R E

: E

LE

V A

T

IO

N S

1'

/4

E Q

E Q

R E

: E

LE

V

DN

BASE UNIT WITH 2 EQUAL 6"

UPPER DRAWERS & 2 EQUAL

8" LOWER DRAWERS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

6" 6"

1/

4"

1/ 4"

RE: PLAN

2' - 0" TYP

3"

4"

R E

: E

LE

V A

T

IO

N S

2"

R E

: E

LE

V R

E : E

LE

V

R E

: E

LE

V R

E : E

LE

V

DP

BASE UNIT WITH

PENCIL DRAWER AND

4 EQUAL DRAWERS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DOOR/DRAWER PULLS AS SCHED, TYP.

BASE AS SCHED.

BLOCKING, TYP.

1/16" MAX GAP BETWEEN

DOOR/DRAWER FRONTS, TYP.

1/

4"

1/ 4"

1/

4"

1/ 4"

2"

2"

RE: PLAN

2' - 0" TYP

3"

E Q

E Q

E Q

E Q

R E

: E

LE

V

4"

R E

: E

LE

V A

T

IO

N S

DT

FULL HEIGHT CABINET

WITH DOOR AND

ADJUSTABLE SHELVES.

BASE AS SCHED.

BLOCKING, TYP.

ADJUSTABLE

SHELF, TYP.

BLOCKING, TYP.

DOOR PULLS AS SCHED, TYP.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

STANLEY OFFSET PIVOT HINGES #327,

TOP AND BOTTOM.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

RE: PLAN

1' - 3" TYP

3" 1"

4"

R E

: E

LE

V A

T

IO

N S

TYP

1' - 1 1/2"

2'

0"

FA FB

FULL HEIGHT CABINET

WITH TWO DOORS AND

ADJUSTABLE SHELVES.

DOOR PULLS AS SCHED, TYP.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

STANLEY OFFSET PIVOT HINGES #327,

TOP AND BOTTOM.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

BLOCKING, TYP.

BASE AS SCHED.

FIXED SHELF.

ADJUSTABLE

SHELF, TYP.

ADJUSTABLE SHELF, TYP.

BLOCKING, TYP.

RE: PLAN

1' - 3" TYP

3" 1"

4"

R E

: E

LE

V A

T

IO

N S

TYP

1' - 1 1/2"

2'

/2

2' -4

/4

2'

0"

FC FD

FULL HEIGHT CABINET WITH NORMAL

STRENGTH ADJUSTABLE SHELVES &

CABINET BELOW.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

BLOCKING, TYP.

BASE AS SCHED.

1/4" PLYWD BACK.

BLOCKING,

TYP.

DOOR PULLS AS SCHED, TYP.

FIXED SHELF.

WHERE OUTLETS ARE

SCHEDULED

WITHIN UNIT, INSTALL

FACE FLUSH

WITH REAR PANEL.

RE: ELEC FOR

LOCATIONS.

ADJUSTABLE SHELF,

TYP.

RE: PLAN

1' - 6" TYP

3"

2'

0"

TYP

1' - 3 1/2"

4"

R E

: E

LE

V A

T

IO

N S

FE FF

R E

: E

LE

V A

T

IO

N S

MICROWAVE OVEN (SEE

APPLIANCE SCHEDULE)

1/4" MELAMINE BACK ON 1/2"

CONTINUOUS BLOCKING

3/4 PLAM FACED SHELF

2'

0"

ELECTRICAL OUTLET AT 42" AFF

INSTALL FACE FLUSH WITH REAR PANEL.

MICROWAVE OVEN (SEE

APPLIANCE SCHEDULE)

3/4 PLAM FACED COUNTERTOP

3/4" SOLID STOCK DRAWER

SIDES AND BACK TYPICAL

3/4" PLAM DOOR/

DRAWER FRONTS TYPICAL

ADJUSTABLE SHELF

1/4" MELAMINE BACK ON 1/2"

CONTINUOUS BLOCKING

SCHEDULED BASE

FJ

FULL HEIGHT CABINET WITH DOUBLE

MICROWAVE & CABINET BELOW.

3" GROMMET, TYP DOUG MOCKETT

XG1 OR EQUAL

2' - 0"

RE: PLAN

E Q

2"

CONCEALED HINGES, TYP.

FIXED SHELF.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

DOOR PULLS, TYP.

E Q

1'

1'

/1 6"

1'

/1 6"

ADJUSTABLE SHELF, TYP.

WHERE OUTLETS ARE

SCHEDULED

WITHIN UNIT, INSTALL

FACE FLUSH

WITH REAR PANEL. RE:

ELEC. FOR LOCATIONS.

FULL HEIGHT CABINET WITH NORMAL

STRENGTH ADJUSTABLE SHELVES.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

BLOCKING, TYP.

BASE AS SCHED.

1/4" PLYWD.

BACK.

BLOCKING, TYP.

1/4"1/4"

RE: PLAN

1' - 6" TYP

3"

4"

R E

: E

LE

V A

T

IO

N S

FO

GENERAL CASEWORK NOTES

1. ALL CASEWORK SHOWN ON THIS SHEET IS PLASTIC LAMINATE CLAD UNO.

2. ALL EXPOSED SURFACES AND EDGES SHALL RECEIVE PLASTIC LAMINATE AS SCHED.

ALL INTERIOR SURFACES AND EDGES SHALL RECEIVE WHITE MELAMINE UNO, TYP.

4. CABINET WIDTHS ARE BASED ON MODULE INCREMENTS OF 3 INCHES FROM 12 TO 36

INCHES WIDE CABINETS AND 6 INCH INCREMENTS FOR 36 TO 48 INCHES OF WIDE

CABINETS.

5. ALL COUNTERTOPS SHALL BE PLASTIC LAMINATE UNO. PROVIDE 3/4" PLYWD

SUBSTRATE FOR ALL WET LOCATIONS. 3/4" MDF AT OTHER LOCATIONS, UNO.

6. REFER TO 83-A-711 THROUGH 83-A-15 FOR MILLWORK DETAILS.

7. REFER TO 83-A-701 FOR SOFFIT/FURR DOWN DETAILS.

8. REFER TO SHEET 83-A-702 THROUGH 83-A-705 FOR TYP CASEWORK DETAILS.

9. INSTALL 3/4" THK BACKSPLASHES AT ALL LOCATIONS UNO. INSTALL 3/4" END

SPLASHES WHEN COUNTER IS ADJACENT TO A PARTITION OR TALLER CASEWORK.

LAMINATE ALL EXPOSED EDGES TO MATCH COUNTERTOP. BACKSPLASH AND END

SPLASH TO BE 4" HIGH UNO.

10. RADIUS ALL OUTSIDE CORNERS OF COUNTERTOPS 1", UNO. DO NOT RADIUS CORNER

IF A FULL HEIGHT REFRIGERATOR IS PLANNED IMMEDIATELY NEXT TO

COUNTERTOP.

11. ADJACENT UPPER CABINETS SHALL HAVE FLUSH BOTTOM TO FORM CONTINUOUS

POCKET BEHIND FRONT VALENCE FOR LIGHT FIXTURES. BOTTOM OF EXPOSED SIDES

SHALL ALIGN WITH FRONT.

12. PROVIDE FILLER PANEL WHERE CASEWORK ABUTS WALL OR HEADER ABOVE, 1 INCH

MINIMUM TO 3 INCH MAXIMUM WIDTH. UNO.

13. PROVIDE FINISHED END PANELS AND/OR END RETURNS AT OPEN ENDED, EXPOSED

CASEWORK OR AT KNEE SPACES.

14. LOCATE GROMMETS 48 INCHES ON CENTER MAX. AT BACK OF COUNTERTOPS ABOVE

KNEE SPACE, ONE GROMMET MIN. PER COUNTERTOP RUN. COORDINATE EXACT

LOCATION WITH OWNER PRIOR TO INSTALLATION. SHOW GROMMET LOCATIONS ON

SHOP DRAWINGS.

16. FIELD VERIFY ALL DIMENSIONS PRIOR TO FABRICATION OF CASEWORK.

17. SOME DETAILS ON THIS SHEET MAY NOT BE USED.

18. PROVIDE FIRE TREATED WOOD BLOCKING WITHIN WALL FOR ALL MOUNTED

CASEWORK.

2' - 6"

2'

0"

ELEVATION PLAN

CASEWORK ELEVATION TYPE

NOMINAL HEIGHT IN INCHES

NOMINAL WIDTH IN INCHES

DESCRIPTION NOMENCLATURE

1 DWR 2DR 1SH 1 DRAWER OVER 2 DOORS W/ 1 SHELF

1PEN, 4DWR EQ 1 PENCIL DRAWER OVER

4 DRAWERS EQUAL SIZE

3OPEN 3 OPEN SPACES

ABBREVIATIONS

BLNK BLANK

CATH CATHETERIZATION

CSWK CASEWORK

CNTR COUNTER

DR DOOR

DWR DRAWER

EQ EQUAL

EQUIP EQUIPMENT

HD HEAVY DUTY

KNEE KNEE SPACE

LCKR LOCKER

OPEN OPEN SPACE(S)

PEN PENCIL DRAWER

REF REFRIGERATOR

SH SHELF OR SHELVES

STOR STORAGE

CASEWORK

TAG

BK

BK

CASEWORK LEGEND

FULL HEIGHT CABINET

WITH TWO DOORS AND

ADJUSTABLE SHELVES.

DOOR PULLS AS SCHED, TYP.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

STANLEY OFFSET PIVOT HINGES #327,

TOP AND BOTTOM.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

BLOCKING, TYP.

ADJUSTABLE SHELF, TYP.

BLOCKING, TYP.

RE: PLAN

2' - 0" 1"

R E

: E

LE

V A

T

IO

N S

3'

FQ

TYP.

1' - 10"

1/ 2"

D A

M P

Drawing Title

Approved Project Director:

Project Title

Date

Location

Checked

Building Number

Project Number

Drawing Number

Drawn

PSP 309070 Revisions Date

ARCHITECT/ENGINEERS: Office of

Construction and Facilities

Management o n e e ig h th in c h o n e fo o t 1 th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t

VA FORM 08-6231

1 2 3 4 5 6 87 9

F

E

D

C

B

A

97 8654321

FILE NAME

Project Abbreviation

F

E

D

C

B

A

F

IL

E N

A M

E

Page Southerland Page, LLP.

1800 Main Street Suite 123

Dallas, TX 75201 pagethink.com

TEL

FAX

ARCHITECTURE / ENGINEERING / INTERIORS / CONSULTING

Austin / Dallas / Denver / Houston / Washington DC /

International Affiliate Offices

214 522 3900

214 522 4380

DWG

W

R e v it

L o ca l\ b A

-S C I_

In te ri o r-

-C

E N

T R A L c ry st a lm cm .r v t

/1

/2

:0 :3

P

M

W:\@RevitLocal\309070b3A-SCI_Interior-2018-CENTRAL_crystalmcm.rvt

83-A-703

CONSTRUCTION

VA-LTSCIF-D

TEAM

549-820B

TAB

ARCHITECTURAL - CASEWORK STANDARDS

LONG TERM SPINAL CORD INJURY

VA NORTH TEXAS HEALTH CARE SYSTEM

4500 S. LANCASTER RD. DALLAS, TX 75216OFFICE OF CONSTRUCTION AND FACILITIES

MANAGEMENT DIRECTOR, CENTRAL REGION

06 MAY 2021

FULLY SPRINKLEREDBID PACKAGE B

SCALE: 1" = 1'-0"F7 BASE CABINET - DB

SCALE: 1" = 1'-0"D7 BASE CABINET - DE

SCALE: 1" = 1'-0"C7 BASE CABINET - DG

SCALE: 1" = 1'-0"A7 BASE CABINET - DH

SCALE: 1" = 1'-0"F6 BASE CABINET - DM

SCALE: 1" = 1'-0"D6 BASE CABINET - DN

SCALE: 1" = 1'-0"C6 BASE CABINET - DP

SCALE: 1" = 1'-0"A6 BASE CABINET - DT

SCALE: 1" = 1'-0"F4 FULL HEIGHT CABINET - FA FB

SCALE: 1" = 1'-0"C4 FULL HEIGHT CABINET - FC FD

SCALE: 1" = 1'-0"F2 FULL HEIGHT CABINET - FE FF

SCALE: 1" = 1'-0"C2 FULL HEIGHT CABINET - FJ

SCALE: 1" = 1'-0"F1 FULL HEIGHT CABINET - FO

SCALE: 1" = 1'-0"C1 FULL HEIGHT CABINET - FQ

A T

T S

XETE FO

S A

M

LAB

1 0 9 0 0

R E G

IS

TE

RED ARCH

ITE

C T

A

I F

A

T T

AI

O N

FIXED SHELF.

DOOR PULL AS SCHED.

WHERE OUTLETS ARE

SCHEDULED

WITHIN UNIT, INSTALL

FACE FLUSH

WITH REAR PANEL. RE:

ELEC FOR LOCATIONS.

ADJUSTABLE SHELF,

TYP.

FULL HEIGHT CABINET FOR

TELEVISION

WITH SLIDE-AWAY DOORS.

BLOCKING, TYP.

BASE AS SCHED.

FINISHED PLAM TOP SURFACE.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

1/4" PLYWD BACK.

BLOCKING, TYP.

3/4" PLAM CLAD PLYWOOD DOOR.

PROVIDE HARDWARE AS REQUIRED FOR

PAIR OF DOORS TO OPEN AND SLIDE

BACK INTO UNIT. MAXIMIZE CLEAR

WIDTH BETWEEN DOORS WHEN OPEN.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

RE: PLAN

2' - 0" TYP

3"

2'

4"

R E

: E

LE

V A

T

IO

N S

1' - 9 1/2"

FT

DOOR PULL AS SCHED, TYP.

BLOCKING,

TYP.

BASE AS SCHED.

PLASTIC LAMINATE

ON ALL EXPOSED

AND SEMI-XPOSED

SURFACES TO

MATCH DOORS AS

SCHED.

FULL HEIGHT WARDROBE

CABINET WITH DOOR AND

CLOTHES ROD.

BLOCKING, TYP.

FIXED SHELF.

1" DIA STAINLESS STEEL CLOTHES

ROD WITH END CAPS.

ADJUSTABLE SHELF.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

STANLEY OFFSET PIVOT HINGES #327,

TOP AND BOTTOM.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

FULL HEIGHT CABINETS.

RE: PLAN

1' - 6" TYP

3" 1"

4'

4"

R E

: E

LE

V A

T

IO

N S

1'

2'

0"

5 1/2"

TYP

1' - 1 1/2"

FW FX

4'

COUNTERTOP WITH

KNEE SPACE.

BASE AS SCHED.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

3/4" PLYWOOD SUPPORT BRACKET,

REFER TO 83-A-701.

FINISHED END PANEL ON CSWK BEYOND.

KEYBOARD TRAY OR PENCIL DRAWER AS

SCHED, RE: ELEVATIONS.

NOTE: WHEN CASEWORK IS LOCATED

BETWEEN PARTITIONS, THE AS-BUILT

WIDTH MAY VARY FROM SCHED, WIDTH

VERIFY IN FIELD BEFORE FABRICATION.

NOTE: WHEN A WIDTH OF 36" OR LESS

IS SCHED, DO NOT REDUCE WIDTH.

RE: PLAN

2' - 0" TYP

R E

: E

LE

V A

T

IO

N S

C

LR

2'

/2

KA

F O

R A

D A

2' -3

C

LR

OPEN KNEE SPACE

UNDER COUNTERTOP.

BASE AS SCHED INSTALL ON SIDES

AND BACK.

FLOOR AS SCHED.

SUPPORT WHERE REQ'D OR INDICATED ON

ELEVATIONS, RE: 83-A-701.

FINISHED END PANEL ON CSWK BEYOND.

PENCIL DRAWER WHERE INDICATED.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

RE: PLAN

2' - 0" TYP

2"

R E

: E

LE

V A

T

IO

N S

4"

KB

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

DRAWER PULLS AS SCHED, TYP.

BASE UNIT WITH

DEEP DRAWER,

OPEN UNDERNEATH.

FINISH ENDS OF ADJ CABINETS.

BASE AS SCHED.

FINISH FLOOR.

2'

R E

: E

LE

V

1/

2"

RE: PLAN

2' - 0" TYP

R E

: E

LE

V A

T

IO

N S

KC

BASE CABINET AT

SINK W/ BOTTOM.

SINK AS SCHED, RE: PLBG.

R E

: E

LE

V

R E

: E

LE

V A

T

IO

N S

3"

4"

RE: PLAN

2' - 0" TYP

SD

CONCEALED HINGES, TYP.

DOOR/DRAWER PULLS, TYP.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

BLOCKING, TYP.

BASE AS SCHED.

BASE AS SCHED INSTALL

ON SIDES AND BACK.

FLOOR AS SCHED.

BASE CABINET AT

SINK W/ DOORS.

CABINET DOOR WITH TOE

SPACE CONNECTED TO

DOOR.

INSTALL PIPE PROTECTION ON ALL

EXPOSED PIPES. THERE SHALL BE NO

SHARP OR ABRASIVE SURFACES (4.24.6).

FINISHED END PANEL ON CSWK BEYOND.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

FIXED SINK FRONT.

SINK AS SCHED, RE: PLBG.

4"

RE: PLAN

2' - 0" TYP

2'

0"

U N

O

ADA REQUIRES AT

LEAST 27" HIGH AND

30" WIDE KNEE

CLEARANCE AT SINK

(4.24.3).

SE

BASE AS SCHED INSTALL

ON SIDES AND BACK.

FLOOR AS SCHED.

OPEN KNEE

SPACE AT SINK.

ADA REQUIRES AT LEAST 27" HIGH,

8" DEEP AND 30" WIDE KNEE

CLEARANCE AT SINK (4.24.3).

REMOVABLE SLOPED FRONT PANEL,

PLAM ON 3/4" PLYWD.

FINISHED END PANEL ON CSWK BEYOND.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

FIXED SINK FRONT.

SINK AS SCHED, RE: PLBG.

4"

RE: PLAN

2' - 0" TYP

2'

0"

U N

O

6"

9" 1'

SF

M

IN

MAX MIN

8"

OFFSET P-TRAP.

BASE AS SCHED INSTALL ON

SIDES AND BACK.

FLOOR AS SCHED.

OPEN KNEE

SPACE AT

SINK.

ADA REQUIRES AT LEAST 27" HIGH AND

30" WIDE KNEE CLEARANCE AT SINK

(4.24.3).

INSTALL PIPE PROTECTION ON ALL

EXPOSED PIPES. THERE SHALL BE NO

SHARP OR ABRASIVE SURFACES (4.24.6).

FINISHED END PANEL ON CSWK BEYOND.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

FIXED SINK FRONT.

SINK AS SCHED, RE: PLBG.

4"

RE: PLAN

2' - 0" TYP

2'

0"

U N

O

SG

MOBILE FILE

STORAGE

CABINET.

2" CASTER.

2"

1/

2"

2'

U N

O

E Q

E Q

M

IN

/4

M

IN

/4

1'-10" TYP

MA

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

DRAWER PULL, TYP

MOBILE FILE SLOTS.

2" CASTER.

LAMINATE SHELF TYP.

E Q

E Q

E Q

1/

2"

1'-10" TYP

1/

2"

2'

U N

O

MB

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

LAMINATE ALL EXPOSED SURFACES TO

MATCH CASEWORK FRONTS.

GROMMET IN EACH SIDE.

MOBILE CPU

STORAGE

CABINET.

2" CASTER.

1'-10" TYP

1/

2"

2'

U N

O

MD

1 1/2" X 6" OPENING IN

BACK PANEL FOR CABLES

AND VENT, TOP AND BOTTOM

1 1/2" THK END PANEL AT ALL EXPOSED

ENDS OF TRANSACTION COUNTER, UNO.

COUNTERTOP.

1/4" REVEAL, TYP.

TRANSACTION COUNTER TERMINUS.

NURSE STATION

FRONT PROFILE.

2" DIA HOLE IN

SUPPORT RIBS

FOR WIRES &

CABLES, TYP.

SCHED LAMINATE ON 2 LAYER 3/4" PLWD.

3/4" PLWD WITH LAMINATE AS SCHED.

WHERE EXPOSED, OTHERWISE WHITE

MELAMINE.

CASEWORK AS SCHED, RE: ELEV.

JUNCTION BOX WHERE NOTED ON

ELEVATIONS OR ELEC DWGS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

TACKABLE SURFACE WHERE NOTED,

RE: 83-A-701.

TRANSACTION COUNTER

DETAIL, REF 83-A-701 AND

ELEVATIONS.

OPENING FOR CABLE ACCESS,

WIDTH OF UNIT LESS 4" TYP.

REMOVABLE PANEL.

BASE AS SCHED,

UNO.

1/4" REVEAL, TYP.

1/4" VERTICAL

REVEALS AS SHOWN

ON ELEVATION AND

AT VERTICAL PLAM

BUTT JOINTS.

5" 3"

RE: PLAN

3'-0" TYP

UNO

1' - 0"

4"

2'

U N

O 1'

1/

2"

NA

1 1/2" THK END PANEL AT ALL EXPOSED

ENDS OF TRANSACTION COUNTER, UNO.

COUNTERTOP.

1/4" REVEAL, TYP.

NURSE STATION

FRONT PROFILE.

OPENING FOR CABLE ACCESS,

WIDTH OF UNIT LESS 4" TYP.

SCHED LAMINATE ON 2 LAYER 3/4" PLWD.

3/4" PLWD. WITH LAMINATE AS SCHED

WHERE EXPOSED, OTHERWISE WHITE

MELAMINE.

CASEWORK AS SCHED, RE: ELEV.

JUNCTION BOX WHERE NOTED ON

ELEVATIONS OR ELEC DWGS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

TACKABLE SURFACE WHERE NOTED,

RE: 83-A-701.

TRANSACTION COUNTER, REF

83-A-701 AND ELEVATIONS.

2" DIA HOLE IN

SUPPORT RIBS

FOR WIRES &

CABLES, TYP.

REMOVABLE PANEL.

BASE AS SCHED,

UNO.

1/4" REVEAL, TYP.

TRANSACTION COUNTER TERMINUS.

1/4" VERTICAL

REVEALS AS

SHOWN ON

ELEVATION AND AT

VERTICAL PLAM

BUTT JOINTS.

4" 5" 3"

RE: PLAN

3'-0" TYP

4"

1/ 2"

2'

U N

O 1'

UNO

1' - 0"

NB

NURSE STATION

FRONT PROFILE.

2" DIA HOLE IN

SUPPORT RIBS

FOR WIRES &

CABLES, TYP.

SCHED LAMINATE ON 2 LAYER 3/4" PLWD.

3/4" PLWD WITH LAMINATE AS SCHED.

WHERE EXPOSED, OTHERWISE WHITE

MELAMINE.

CASEWORK AS SCHED, RE: ELEV.

JUNCTION BOX WHERE NOTED ON

ELEVATIONS OR ELEC DWGS.

COUNTERTOP AS SPECIFIED,

REF TO 83-A-701 AND

ELEVATIONS.

TACKABLE SURFACE WHERE NOTED,

RE: 83-A-701.

TRANSACTION COUNTER, REF 83-A-701.

OPENING FOR CABLE ACCESS,

WIDTH OF UNIT LESS 4" TYP.

REMOVABLE PANEL.

BASE AS SCHED

UNO.

TRANSACTION COUNTER TERMINUS.

1/4" VERTICAL

REVEALS AS SHOWN

ON ELEVATION AND

AT VERTICAL PLAM

BUTT JOINTS.

1 1/2" THK END PANEL AT ALL EXPOSED

ENDS OF TRANSACTION COUNTER, UNO.

COUNTER TOP.

1/4" REVEAL, TYP.

UNO

1' - 0"

4" 2" 4"

RE: PLAN

3'-0" TYP

4"

2'

U N

O 1'

/1

NC

1 1/2" THK END PANEL AT ALL EXPOSED

ENDS OF TRANSACTION COUNTER, UNO.

COUNTERTOP.

NURSE STATION

FRONT PROFILE.

2" DIA HOLE IN

SUPPORT RIBS

FOR WIRES &

CABLES, TYP.

SCHED LAMINATE ON 2 LAYER 3/4" PLWD.

3/4" PLWD. WITH LAMINATE AS SCHED

WHERE EXPOSED, OTHERWISE WHITE

MELAMINE.

CASEWORK AS SCHED, RE: ELEV.

JUNCTION BOX WHERE NOTED ON

ELEVATIONS OR ELEC DWGS.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

TACKABLE SURFACE WHERE NOTED,

RE: 83-A-701.

TRANSACTION COUNTER, REF 83-A-701.

OPENING FOR CABLE ACCESS.

WIDTH OF UNIT LESS 4" TYP.

REMOVABLE PANEL.

BASE AS SCHED,

UNO.

1/4" REVEAL, TYP.

TRANSACTION COUNTER TERMINUS.

1/4" VERTICAL

REVEALS AS SHOWN

ON ELEVATION AND

AT VERTICAL PLAM

BUTT JOINTS.

LIGHT FIXTURE, RE: ELECTRICAL.

WHITE PLAM ALL SURFACES INSIDE BOX.

0' - 6"

UNO

0' - 6"

4" 2" 4"

RE: PLAN

3'-0" TYP

4"

2'

U N

O 1'

/1

/1

ND

BASE AS SCHED

INSTALL ON SIDES.

FLOOR AS SCHED.

OPEN KNEE SPACE AT

SINK WITH TOE KICK

PANEL.

ADA REQUIRES AT LEAST 27" HIGH,

8" DEEP AND 30" WIDE KNEE

CLEARANCE AT SINK (4.24.3).

REMOVABLE SLOPED FRONT PANEL,

PLAM ON 3/4" PLYWD.

FINISHED END PANEL ON CSWK BEYOND.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

FIXED SINK FRONT.

SINK AS SCHED, RE: PLBG.

4"

RE: PLAN

2' - 0" TYP

2'

0"

U N

O

9" 1'

SH

10" 8"

OFFSET P-TRAP.

1' - 7"

REMOVEABLE PANEL,

MATCH CABINET FINISH.

GENERAL CASEWORK NOTES

1. ALL CASEWORK SHOWN ON THIS SHEET IS PLASTIC LAMINATE CLAD UNO.

2. ALL EXPOSED SURFACES AND EDGES SHALL RECEIVE PLASTIC LAMINATE AS SCHED.

ALL INTERIOR SURFACES AND EDGES SHALL RECEIVE WHITE MELAMINE UNO, TYP.

4. CABINET WIDTHS ARE BASED ON MODULE INCREMENTS OF 3 INCHES FROM 12 TO 36

INCHES WIDE CABINETS AND 6 INCH INCREMENTS FOR 36 TO 48 INCHES OF WIDE

CABINETS.

5. ALL COUNTERTOPS SHALL BE PLASTIC LAMINATE UNO. PROVIDE 3/4" PLYWD

SUBSTRATE FOR ALL WET LOCATIONS. 3/4" MDF AT OTHER LOCATIONS, UNO.

6. REFER TO 83-A-711 THROUGH 83-A-15 FOR MILLWORK DETAILS.

7. REFER TO 83-A-701 FOR SOFFIT/FURR DOWN DETAILS.

8. REFER TO SHEET 83-A-702 THROUGH 83-A-705 FOR TYP CASEWORK DETAILS.

9. INSTALL 3/4" THK BACKSPLASHES AT ALL LOCATIONS UNO. INSTALL 3/4" END

SPLASHES WHEN COUNTER IS ADJACENT TO A PARTITION OR TALLER CASEWORK.

LAMINATE ALL EXPOSED EDGES TO MATCH COUNTERTOP. BACKSPLASH AND END

SPLASH TO BE 4" HIGH UNO.

10. RADIUS ALL OUTSIDE CORNERS OF COUNTERTOPS 1", UNO. DO NOT RADIUS CORNER

IF A FULL HEIGHT REFRIGERATOR IS PLANNED IMMEDIATELY NEXT TO

COUNTERTOP.

11. ADJACENT UPPER CABINETS SHALL HAVE FLUSH BOTTOM TO FORM CONTINUOUS

POCKET BEHIND FRONT VALENCE FOR LIGHT FIXTURES. BOTTOM OF EXPOSED SIDES

SHALL ALIGN WITH FRONT.

12. PROVIDE FILLER PANEL WHERE CASEWORK ABUTS WALL OR HEADER ABOVE, 1 INCH

MINIMUM TO 3 INCH MAXIMUM WIDTH. UNO.

13. PROVIDE FINISHED END PANELS AND/OR END RETURNS AT OPEN ENDED, EXPOSED

CASEWORK OR AT KNEE SPACES.

14. LOCATE GROMMETS 48 INCHES ON CENTER MAX. AT BACK OF COUNTERTOPS ABOVE

KNEE SPACE, ONE GROMMET MIN. PER COUNTERTOP RUN. COORDINATE EXACT

LOCATION WITH OWNER PRIOR TO INSTALLATION. SHOW GROMMET LOCATIONS ON

SHOP DRAWINGS.

16. FIELD VERIFY ALL DIMENSIONS PRIOR TO FABRICATION OF CASEWORK.

17. SOME DETAILS ON THIS SHEET MAY NOT BE USED.

18. PROVIDE FIRE TREATED WOOD BLOCKING WITHIN WALL FOR ALL MOUNTED

CASEWORK.

2' - 6"

2'

0"

ELEVATION PLAN

CASEWORK ELEVATION TYPE

NOMINAL HEIGHT IN INCHES

NOMINAL WIDTH IN INCHES

DESCRIPTION NOMENCLATURE

1 DWR 2DR 1SH 1 DRAWER OVER 2 DOORS W/ 1 SHELF

1PEN, 4DWR EQ 1 PENCIL DRAWER OVER

4 DRAWERS EQUAL SIZE

3OPEN 3 OPEN SPACES

ABBREVIATIONS

BLNK BLANK

CATH CATHETERIZATION

CSWK CASEWORK

CNTR COUNTER

DR DOOR

DWR DRAWER

EQ EQUAL

EQUIP EQUIPMENT

HD HEAVY DUTY

KNEE KNEE SPACE

LCKR LOCKER

OPEN OPEN SPACE(S)

PEN PENCIL DRAWER

REF REFRIGERATOR

SH SHELF OR SHELVES

STOR STORAGE

CASEWORK

TAG

BK

BK

CASEWORK LEGEND

BASE AS SCHED INSTALL

ON SIDES AND BACK.

FLOOR AS SCHED.

OPEN KNEE

SPACE AT SINK.

ADA REQUIRES AT LEAST 27" HIGH,

8" DEEP AND 30" WIDE KNEE

CLEARANCE AT SINK (4.24.3).

REMOVABLE SLOPED FRONT PANEL,

PLAM ON 3/4" PLYWD.

FINISHED END PANEL ON CSWK BEYOND.

COUNTERTOP AS SPECIFIED, REF

TO 83-A-701 AND ELEVATIONS.

SINK AS SCHED, RE: PLBG.

RE: PLAN

2' - 0" TYP

2'

0"

U N

O

6"

9" 1'

SI

M

IN

MAX MIN

8"

OFFSET P-TRAP.

D A

M P

Drawing Title

Approved Project Director:

Project Title

Date

Location

Checked

Building Number

Project Number

Drawing Number

Drawn

PSP 309070 Revisions Date

ARCHITECT/ENGINEERS: Office of

Construction and Facilities

Management o n e e ig h th in c h o n e fo o t 1 th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t

VA FORM 08-6231

1 2 3 4 5 6 87 9

F

E

D

C

B

A

97 8654321

FILE NAME

Project Abbreviation

F

E

D

C

B

A

F

IL

E N

A M

E

Page Southerland Page, LLP.

1800 Main Street Suite 123

Dallas, TX 75201 pagethink.com

TEL

FAX

ARCHITECTURE / ENGINEERING / INTERIORS / CONSULTING

Austin / Dallas / Denver / Houston / Washington DC /

International Affiliate Offices

214 522 3900

214 522 4380

DWG

W

R e v it

L o ca l\ b A

-S C I_

In te ri o r-

-C

E N

T R A L c ry st a lm cm .r v t

/1

/2

:0 :4

P

M

W:\@RevitLocal\309070b3A-SCI_Interior-2018-CENTRAL_crystalmcm.rvt

83-A-704

CONSTRUCTION

VA-LTSCIF-D

TEAM

549-820B

TAB

ARCHITECTURAL - CASEWORK STANDARDS

LONG TERM SPINAL CORD INJURY

VA NORTH TEXAS HEALTH CARE SYSTEM

4500 S. LANCASTER RD. DALLAS, TX 75216OFFICE OF CONSTRUCTION AND FACILITIES

MANAGEMENT DIRECTOR, CENTRAL REGION

06 MAY 2021

FULLY SPRINKLEREDBID PACKAGE B

SCALE: 1" = 1'-0"F4 FULL HEIGHT CABINET - FT

SCALE: 1" = 1'-0"F2 FULL HEIGHT CABINET - FW FX

SCALE: 1" = 1'-0"F7 BASE CABINET - KA

SCALE: 1" = 1'-0"D7 BASE CABINET - KB

SCALE: 1" = 1'-0"C7 BASE CABINET - KC

SCALE: 1" = 1'-0"A7 BASE CABINET - SD

SCALE: 1" = 1'-0"F6 BASE CABINET - SE

SCALE: 1" = 1'-0"D6 BASE CABINET - SF

SCALE: 1" = 1'-0"C6 BASE CABINET - SG

SCALE: 1" = 1'-0"F1 MOBILE BASE CABINET - MA

SCALE: 1" = 1'-0"E1 MOBILE BASE CABINET - MB

SCALE: 1" = 1'-0"D1 MOBILE BASE CABINET - MD

SCALE: 1" = 1'-0"D4 NURSE STATION - NA

SCALE: 1" = 1'-0"B4 NURSE STATION - NB

SCALE: 1" = 1'-0"D2 NURSE STATION - NC

SCALE: 1" = 1'-0"B2 NURSE STATION - ND

SCALE: 1" = 1'-0"A6 BASE CABINET - SH

SCALE: 1" = 1'-0"B1 BASE CABINET - SF

A T

T S

XETE FO

S A

M

LAB

1 0 9 0 0

R E G

IS

TE

RED ARCH

ITE

C T

A

I F

A

T T

AI

O N

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

UPPER CABINET

DOOR PULLS, TYP.

CONCEALED HINGES, TYP.

BLOCKING, TYP.

1/ 2"

1'

/2

RE: PLAN

1' - 3" UNO

6' -0

A

F F

U N

O

UA UB

ONLY AT FURR DOWNS

U N

O

5' -0

A

F F

U N

O

UPPER CABINET W/

ADJUSTABLE SHELF.

ADJUSTABLE SHELF, TYP.

CONCEALED HINGES, TYP.

DOOR PULLS, TYP.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

VALANCE TERMINATES

INTO OUTER END PANELS.

CONTINUOUS POCKET AT UPPER

BOTTOM WITH SCHED LAMINATE

ON ALL EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

BLOCKING, TYP.

2"

2'

/2

" TYP

1' - 1 1/2"

RE: PLAN

1' - 3" UNO

UC UD

1/ 2"

U N

O

ONLY AT FURR DOWNS

4' -6

A

F F

U N

O

VALANCE TERMINATES

INTO OUTER END PANELS.

CONTINUOUS POCKET AT UPPER

BOTTOM WITH SCHED LAMINATE ON

ALL EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

UPPER CABINET W/

ADJUSTABLE SHELVES.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL

BLOCKING BEHIND GYP BD

ENTIRE LENGTH OF UPPER

CABINETS.

CONCEALED HINGES, TYP.

DOOR PULLS, TYP.

ADJUSTABLE SHELVES, TYP.

BLOCKING, TYP.

RE: PLAN

1' - 3" UNO

2"

R E

: E

LE

V A

T

IO

N S

TYP

1' - 1 1/2"

UE UF

ONLY AT FURR DOWNS

1/ 2"

UPPER CABINET -

OPEN SHELF.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

BLOCKING, TYP.

1/

2"

RE: PLAN

1' - 3" UNO

1' -0

U

N O

6' -0

A

F F

U N

O

UG

5' -0

A

F F

U N

O 2"

VALANCE TERMINATES INTO

OUTER END PANELS.

CONTINUOUS POCKET AT

UPPER BOTTOM WITH

SCHED LAMINATE ON ALL

EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

ADJUSTABLE SHELF, TYP.

UPPER CABINET W/

ADJUSTABLE SHELF.

BLOCKING, TYP.

2"

2'

U N

O

RE: PLAN

1' - 3" UNO

UH

4' -6

A

F F

U N

O

UPPER CABINET W/

ADJUSTABLE

SHELF.

ADJUSTABLE HEAVY DUTY SHELF.

VALANCE TERMINATES

INTO OUTER END

PANELS.

CONTINUOUS POCKET

AT UPPER BOTTOM

WITH SCHED LAMINATE

ON ALL EXPOSED

SURFACES.

LIGHT FIXTURE

WHERE SCHED, RE:

ELEC.

BLOCKING, TYP.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

R E

:E

LE

V A

T

IO

N S

2"

RE: PLAN

1' - 3" UNO

UJ

UPPER CABINET W/

ADJUSTABLE SHELVES.

VALANCE TERMINATES INTO

OUTER END PANELS.

CONTINUOUS POCKET AT

UPPER BOTTOM WITH

SCHED LAMINATE ON ALL

EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

ADJUSTABLE SHELF, TYP.

BLOCKING, TYP.

RE: PLAN

1' - 3" UNO

2"

R E

: E

LE

V A

T

IO

N S

4' -6

A

F F

U N

O

UK

SEE ABV

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

CONCEALED HINGES, TYP.

FIXED SHELF.

BLOCKING, TYP.

UPPER OPEN

SHELF/ CABINET.

VALANCE TERMINATES INTO

OUTER END PANELS, RADIUS

TO MATCH PLAN.

CONTINUOUS POCKET

AT UPPER BOTTOM

WITH SCHED LAMINATE

ON ALL EXPOSED

SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

PLAN DETAIL.

EDGE OF SHELF.

EDGE OF CABINET ABOVE.

R

RE: PLAN

1' - 3" UNO 4"

2" 1'

1/ 2"

R E

: E

LE

V A

T

IO

N S

4' -6

A

F F

U N

O

UM

DOOR PULLS, TYP.

4' -6

A

F F

U N

O

INSTALL MIN 6" WIDE METAL

BLOCKING BEHIND GYP BD ENTIRE

LENGTH OF UPPER CABINETS.

CONCEALED HINGES, TYP.

FIXED SHELF.

BLOCKING, TYP.

UPPER OPEN

SHELF/ CABINET.

CONTINUOUS POCKET AT UPPER

BOTTOM WITH SCHED LAMINATE

ON ALL EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

RE: PLAN

1' - 3" UNO

1/

2" 1'

2"

V N

'-6

U N

O

U N

'-6

U N

O

UN U0

DOOR PULLS, TYP.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

5' -0

A

F F

U N

O

SEE ABV

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

BLOCKING, TYP.

UPPER OPEN

SHELF/ CABINET.

VALANCE TERMINATES INTO OUTER END

PANELS, RADIUS TO MATCH PLAN.

CONTINUOUS POCKET AT UPPER BOTTOM

WITH SCHED LAMINATE ON ALL

EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

PLAN DETAIL.

EDGE OF SHELF.

EDGE OF CABINET ABOVE.

WHEN OUTLETS ARE LOCATED BEHIND

UNIT, FACE PLATE SHALL BE

INSTALLED ON BACK SURFACE.

R 3"

2" 1'

C

LR

2'

U N

O

RE: PLAN

1' - 3" UNO 4"

UQ

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

CONCEALED HINGES, TYP.

FIXED SHELF.

BLOCKING, TYP.

UPPER OPEN

SHELF/ CABINET.

CONTINUOUS POCKET AT UPPER

BOTTOM WITH SCHED LAMINATE

ON ALL EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

1/

2" 1'

2"

V N

'-6

U N

O

U N

U

N O

RE: PLAN

1' - 3" UNO

4' -6

A

F F

U N

O

UR US

REFER TO ELEVATION FOR SOFFIT

CONDITION.

DOOR PULLS, TYP.

ACCESSORIES AS SCHED

RE: INTERIOR ELEVATIONS OR

EQUIP PLANS.

UPPER CABINET W/

ACCESSORY PANEL.

VALANCE TERMINATES INTO

OUTER END PANELS.

CONTINUOUS POCKET

AT UPPER BOTTOM WITH

SCHED LAMINATE ON

ALL

EXPOSED SURFACES.

LIGHT FIXTURE WHERE

SCHED, RE: ELEC.

CONCEALED HINGES, TYP.

DOOR PULLS, TYP.

BLOCKING, TYP.

3/4" FIXED PLYWOOD SHELF AND

CASE

CONSTRUCTION, TYPICAL SHELF AT

SOAP DISP SIDE ONLY. RE: INTERIOR

ELEVATIONS.

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD LENGTH OF UPPER

CABINETS AT SOAP DISP SIDE.

7"

RE: PLAN

1' - 3" UNO

2" 1'

2' -0

U

N O

5' -0

A

F F

U N

O

UT

4' -6

A

F F

U N

O

REFER TO ELEVATION FOR SOFFIT

CONDITION.

INSTALL MIN 6" WIDE METAL BLOCKING

BEHIND GYP BD ENTIRE LENGTH OF

UPPER CABINETS.

CONCEALED HINGES, TYP.

DOOR PULLS, TYP.

DOORS SWING UP AND SLIDE BACK

INTO POCKET, TYP.

UPPER CABINET W/

FIXED SHELVES AND

SWING & SLIDE

DOORS.

RE: PLAN

1' - 3" UNO

1' -0

M

IN

C

LR

2"

R E

: E

LE

V A

T

IO

N S

1' -1

M

IN

C

LR

UU

2' - 6"

2'

0"

ELEVATION PLAN

CASEWORK ELEVATION TYPE

NOMINAL HEIGHT IN INCHES

NOMINAL WIDTH IN INCHES

DESCRIPTION NOMENCLATURE

1 DWR 2DR 1SH 1 DRAWER OVER 2 DOORS W/ 1 SHELF

1PEN, 4DWR EQ 1 PENCIL DRAWER OVER

4 DRAWERS EQUAL SIZE

3OPEN 3 OPEN SPACES

ABBREVIATIONS

BLNK BLANK

CATH CATHETERIZATION

CSWK CASEWORK

CNTR COUNTER

DR DOOR

DWR DRAWER

EQ EQUAL

EQUIP EQUIPMENT

HD HEAVY DUTY

KNEE KNEE SPACE

LCKR LOCKER

OPEN OPEN SPACE(S)

PEN PENCIL DRAWER

REF REFRIGERATOR

SH SHELF OR SHELVES

STOR STORAGE

CASEWORK

TAG

BK

BK

CASEWORK LEGEND

GENERAL CASEWORK NOTES

1. ALL CASEWORK SHOWN ON THIS SHEET IS PLASTIC LAMINATE CLAD UNO.

2. ALL EXPOSED SURFACES AND EDGES SHALL RECEIVE PLASTIC LAMINATE AS SCHED.

ALL INTERIOR SURFACES AND EDGES SHALL RECEIVE WHITE MELAMINE UNO, TYP.

4. CABINET WIDTHS ARE BASED ON MODULE INCREMENTS OF 3 INCHES FROM 12 TO 36

INCHES WIDE CABINETS AND 6 INCH INCREMENTS FOR 36 TO 48 INCHES OF WIDE

CABINETS.

5. ALL COUNTERTOPS SHALL BE PLASTIC LAMINATE UNO. PROVIDE 3/4" PLYWD

SUBSTRATE FOR ALL WET LOCATIONS. 3/4" MDF AT OTHER LOCATIONS, UNO.

6. REFER TO 83-A-711 THROUGH 83-A-15 FOR MILLWORK DETAILS.

7. REFER TO 83-A-701 FOR SOFFIT/FURR DOWN DETAILS.

8. REFER TO SHEET 83-A-702 THROUGH 83-A-705 FOR TYP CASEWORK DETAILS.

9. INSTALL 3/4" THK BACKSPLASHES AT ALL LOCATIONS UNO. INSTALL 3/4" END

SPLASHES WHEN COUNTER IS ADJACENT TO A PARTITION OR TALLER CASEWORK.

LAMINATE ALL EXPOSED EDGES TO MATCH COUNTERTOP. BACKSPLASH AND END

SPLASH TO BE 4" HIGH UNO.

10. RADIUS ALL OUTSIDE CORNERS OF COUNTERTOPS 1", UNO. DO NOT RADIUS CORNER

IF A FULL HEIGHT REFRIGERATOR IS PLANNED IMMEDIATELY NEXT TO

COUNTERTOP.

11. ADJACENT UPPER CABINETS SHALL HAVE FLUSH BOTTOM TO FORM CONTINUOUS

POCKET BEHIND FRONT VALENCE FOR LIGHT FIXTURES. BOTTOM OF EXPOSED SIDES

SHALL ALIGN WITH FRONT.

12…